Samsung WF407, WF409 User Manual

Washer
user manual
imagine the possibilities
Thank you for purchasing this Samsung product. To receive more complete service, please register your product at
www.samsung.com/register
WF409ANW-02657D_EN.indd 1 2009-08-11 ø¿»ƒ 3:10:07
2_ features of your new VRT™ STEAM washer
features of your new VRT™ STEAM washer
1. VRT™ (Vibration Reduction Technology)
This Samsung washer performs smoothly at top spin speeds, minimizing noise and vibration.
2. Super capacity
Samsung’s extra-large capacity laundry machine can wash a full set of your bedding, a king­size comforter, or up to 26 bath towels in a single load. Since you don’t have to do as many loads, you save time, money, water and energy.
3. Diamond drum™
Take gentle care of your fabrics. With inside holes 36% smaller than those of conventional drums, the diamond drum prevents fabrics from sticking out and consequently being damaged.
4. Stylish design
The stylish design of this washer blends well with your environment.
5. Digital display & Center jog dial
The jog dial enables you to select cycles in both directions with ease, and the display is easy to use and understand.
6. DD(Direct-drive) Motor
The power to handle anything! Our direct-drive inverter motor delivers power right to the washer drum from a variable speed, reversible motor. A beltless direct-drive motor generates a higher spin speed of 1,200 rpm for more effective, quiet operation. The washer also has fewer moving parts, meaning fewer repairs.
7. Sanitize
When selecting this cycle, the water heats to an extra high temperature to remove 99.9% of certain bacteria typically found on clothing, bedding, or towels. This certification is conducted by NSF International, an independent third-party testing and certification organization. Please check garment care label to avoid garment damage. Only Sanitize cycles have been designed to meet the requirements of this protocol for sanitization efficacy.
NSF Protocol P172 Sanitization Performance of Residential and Commercial, Family-Sized Clothes Washers
WF409ANW-02657D_EN.indd 2 2009-08-11 ø¿»ƒ 3:10:07
features of your new VRT™ STEAM washer _3
8. Pedestal with storage drawer (Model No: WE357A7P/E/W/R)
An optional 15in.(38.1cm) pedestal is available to raise the washer for easier loading and unloading. It also offers a built-in storage drawer that can hold a 100oz.(6.25 lb) bottle of detergent.
9. Stacking (Model No: SK-3A1/XAA, SK-4A/XAA, SK-5A/XAA)
Samsung washer and dryer can be stacked to maximize usable space. An optional stacking kit is available for purchase from your Samsung retailer.
10. Deep steam (WF407 Series only)
The deep steam feature boosts cleaning performance and loosens grime and dirt, thus providing superior cleaning results.
<Pedestal with Storage Drawer> <Stacking>
WF409ANW-02657D_EN.indd 3 2009-08-11 ø¿»ƒ 3:10:08
4_ safety information
safety information
Congratulations on your new Samsung ActivFresh™ washer. This manual contains important information on the installation, use and care of your appliance. Please take time to read this manual to take full advantage of your washer’s many benefits and features.
WHAT YOU NEED TO KNOW ABOUT SAFETY INSTRUCTIONS
Warnings and Important Safety Instructions in this manual do not cover all possible conditions and situations that may occur. It is your responsibility to use common sense, caution, and care when installing, maintaining, and operating your washer.
IMPORTANT SAFETY SYMBOLS AND PRECAUTIONS
What the icons and signs in this user manual mean:
WARNING
Hazards or unsafe practices that may result in severe personal injury or death.
CAUTION
Hazards or unsafe practices that may result in minor personal injury or property damage
.
CAUTION
To reduce the risk of fire, explosion, electric shock, or personal injury when using your washer, follow these basic safety precautions:
Do NOT attempt.
Do NOT disassemble.
Do NOT touch.
Follow directions explicitly.
Unplug the power plug from the wall socket.
Make sure the machine is grounded to prevent electric shock.
Call the service center for help.
Note
These warning signs are here to prevent injury to you and others. Please follow them explicitly. After reading this section, keep it in a safe place for future reference.
Read all instructions before using the appliance.
SAVE THESE INSTRUCTIONS
WF409ANW-02657D_EN.indd 4 2009-08-11 ø¿»ƒ 3:10:10
safety information _5
WARNING: To reduce the risk of fire, electric shock, or injury to persons when using your
appliance, follow basic precautions, including the following:
1. Read all instructions before using the appliance.
2. Do not wash or dry articles that have been previously cleaned in, washed in, soaked in, or spotted with gasoline, dry-cleaning solvents, other flammable or explosive substances as they give off vapors that could ignite or explode.
3. Do not allow children to play on or in the appliance. Close supervision of children is necessary when the appliance is used near children.
4. Before the appliance is removed from service or discarded, remove the door to the washing or drying compartment.
5. Do not reach into the appliance if the drum is moving.
6. Do not install or store this appliance where it will be exposed to the weather.
7. Do not tamper with controls.
8. Do not repair or replace any part of the appliance or attempt any servicing unless specifically recommended in the user-maintenance instructions or in published user­repair instructions that you understand and have the skills to carry out.
9. Do not add gasoline, dry-cleaning solvents, or other flammable or explosive substances to the wash water. These substances give off vapors that could ignite or explode.
10.Under certain conditions, hydrogen gas may be produced in a hot water system that has not been used for 2 weeks or more. HYDROGEN GAS IS EXPLOSIVE. If the hot water system has not been used for such a period, before using a washer or combination washer-dryer, turn on all hot water faucets and let the water flow from each for several minutes. This will release any accumulated hydrogen gas. As the gas is flammable, do not smoke or use an open flame during this time.
SAVE THESE INSTRUCTIONS
WARNING
WF409ANW-02657D_EN.indd 5 2009-08-11 ø¿»ƒ 3:10:10
6_ safety information
SEVERE WARNING SIGNS FOR INSTALLATION
Plug the power cord into an AC 120V/60Hz/15A wall socket or higher and use the socket for this appliance only. In addition, do not use an extension cord.
- Sharing a wall socket with other appliances using a power strip or extending the power cord may result in electric shock or fire.
- Do not use an electric transformer. It may result in electric shock or fire.
- Ensure that the power voltage, frequency and current are the same as those of the product specifications. Failing to do so may result in electric shock or fire.
The installation of this appliance must be performed by a qualified technician or service company.
- Failing to do so may result in electric shock, fire, an explosion, problems with the product, or injury.
Remove all foreign substances such as dust or water from the power plug terminals and contact points using a dry cloth on a regular basis.
- Unplug the power plug and clean it with a dry cloth.
- Failing to do so may result in electric shock or fire.
Plug the power plug into the wall socket in the right direction so that the cord runs towards the floor.
- If you plug the power plug into the socket in the opposite direction, the electric wires within the cable may be damaged and this may result in electric shock or fire.
This appliance must be properly grounded. Do not ground the appliance to a gas pipe, plastic water pipe, or telephone line.
- This may result in electric shock, fire, an explosion, or problems with the product
- Never plug the power cord into a socket that is not grounded correctly and make sure that it is in accordance with local and national codes.
Do not install this appliance near a heater, inflammable material. Do not install this appliance in a humid, oily or dusty location, in a location exposed to direct sunlight and water (rain drops). Do not install this appliance in a location where gas may leak.
- This may result in electric shock or fire.
Plug the power plug into the wall socket firmly. Do not use a damaged power plug, damaged power cord or loose wall socket.
- This may result in electric shock or fire.
Do not pull or excessively bend the power cord. Do not twist or tie the power cord. Do not hook the power cord over a metal object, place a heavy object on the power cord, insert the power cord between objects, or push the power cord into the space behind the appliance.
- This may result in electric shock or fire.
Do not pull the power cord, when unplugging the power plug.
- Unplug the power plug by holding the plug.
- Failing to do so may result in electric shock or fire.
When the power plug or power cord is damaged, contact your nearest service center.
safety information
WARNING
WF409ANW-02657D_EN.indd 6 2009-08-11 ø¿»ƒ 3:10:11
safety information _7
CAUTION SIGNS FOR INSTALLATION
This appliance should be positioned in such a way that it is accessible to the power plug.
- Failing to do so may result in electric shock or fire due to electric leakage. Install your appliance on a level and hard floor that can support its weight.
- Failing to do so may result in abnormal vibrations, noise, or problems with the product.
Unplug the power plug when the appliance is not being used for long periods of time or during a thunder/lightning storm.
- Failing to do so may result in electric shock or fire.
SEVERE WARNING SIGNS FOR USING
If the appliance is flooded, cut the power immediately and contact your nearest service center. If the appliance generates a strange noise, a burning smell or smoke, unplug the power plug immediately and contact your nearest service center.
- Failing to do so may result in electric shock or fire. In the event of a gas leak (such as propane gas, LP gas, etc.), ventilate immediately without
touching the power plug. Do not touch the appliance or power cord.
- Do not use a ventilating fan.
- A spark may result in an explosion or fire. Do not wash items contaminated with gasoline, kerosene, benzene, paint thinner, alcohol or
other flammable or explosive substances.
- This may result in electric shock, fire or an explosion. Do not open the washer door by force while it is operating (high-temperature washing/
drying/spinning).
- Water flowing out of the washer may result in burns or cause the floor to be slippery. This may result in injury.
- Opening the door by force may result in damage to the product or injury.
Make sure to remove the packaging (sponge, styrofoam) attached to the bottom of the washer before using it.
Do not insert your hand under the washer.
- This may result in injury.
WARNING
CAUTION
WF409ANW-02657D_EN.indd 7 2009-08-11 ø¿»ƒ 3:10:11
8_ safety information
safety information
Do not touch the power plug with wet hands.
- This may result in electric shock. Do not turn the appliance off by unplugging the power plug while an operation is in
progress.
- Plugging the power plug into the wall socket again may cause a spark and result in electric shock or fire.
Keep all packaging materials well out of the reach of children, as packaging materials can be dangerous to children.
- If a child places a bag over its head, it may result in suffocation.
Do not let children or infirm persons use this washer unsupervised.
- Failing to do so may result in electric shock, burns or injury.
Do not insert your hand or a metal object under the washer while it is operating.
- This may result in injury.
Do not attempt to repair, disassemble, or modify the appliance yourself.
- Do not use any fuse(such as cooper, steel wire, etc.) other than the standard fuse.
- When repairing or reinstalling the appliance is required, contact your nearest service center.
- Failing to do so may result in electric shock, fire, problems with the product, or injury.
If any foreign substance such as water has entered the appliance, unplug the power plug and contact your nearest service center.
- Failing to do so may result in electric shock or fire.
When the water supply hose comes loose from the faucet and floods the appliance, unplug the power plug.
- Failing to do so may result in electric shock or fire.
CAUTION SIGNS FOR USING
When the washer is contaminated by a foreign substance such as detergent, dirt, food waste, etc., unplug the power plug and clean the washer using a damp and soft cloth.
- Failing to do so may result in discoloration, deformation, damage or rust.
The front glass may be broken by a strong impact. Take care when using the washer.
- When the glass is broken, it may result in injury.
After a water supply failure or when reconnecting the water supply hose, open the faucet slowly. Open the faucet slowly after a long period of non-use.
- The air pressure in the water supply hose or the water pipe may result in damage to a part or in water leakage.
If a drain error occurs during an operation, check if there is a draining problem.
- If the washer is used when it is flooded because of a draining problem, it may result in electric shock or fire due to electric leakage.
CAUTION
WF409ANW-02657D_EN.indd 8 2009-08-11 ø¿»ƒ 3:10:11
safety information _9
Insert the laundry into the washer completely so that laundry does not get caught in the door.
- If laundry gets caught in the door, it may result in damage to the laundry or the washer, or result in water leakage.
Ensure that the faucet is turned off when the washer is not being used.
- Ensure that the screw on the water supply hose connector is properly tightened.
- Failing to do so may result in property damage or injury.
Check if the rubber seal is not contaminated by foreign substances (waste, thread, etc).
- If the door is not closed completely, it may result in water leakage.
Open the faucet and check if the water supply hose connector is firmly tightened and that there is no water leaking before using the product.
- If the screws or the water supply hose connector are loose, it may result in water leakage.
Do not stand on top of the appliance or place objects (such as laundry, lighted candles, lighted cigarettes, dishes, chemicals, metal objects, etc.) on the appliance.
- This may result in electric shock, fire, problems with the product, or injury.
Do not operate the appliance with wet hands.
- This may result in electric shock.
Do not spray volatile material such as insecticide onto the surface of the appliance.
- As well as being harmful to humans, it may also result in electric shock, fire or problems with the product.
Do not place an object that generates a electromagnetic field near the washer.
- This may result in injury due to a malfunction.
Since the water drained during a high-temperature wash or drying cycle is hot, do not touch the water.
- This may result in burns or injury.
Do not wash, spin or dry water-proof seats, mats or clothing (*).
- Do not wash thick, hard mats even if the washer mark is on the care label.
- This may result in injury or damage to the washer, walls, floor or clothing due to abnormal vibrations.
* Woolen bedding, rain covers, fishing vests, ski pants, sleeping bags, diaper covers,
sweat suits, and bicycle, motor cycle, car covers, etc.
Do not operate the washer when the detergent box is removed.
- This may result in electric shock or injury due to water leakage.
Do not touch the inside of the tub during or just after drying as it is hot.
- This may result in burns.
Do not insert your hand into the detergent box after opening it.
- This may result in injury as your hand may be caught by the detergent input device.
WF409ANW-02657D_EN.indd 9 2009-08-11 ø¿»ƒ 3:10:11
10_ safety information
Do not place any objects (such as shoes, food waste, animals) other than laundry into the washer.
- This may result in damage to the washer, or injury and death in the case of pets due to the abnormal vibrations.
Do not press the buttons using sharp objects such as pins, knifes, fingernails, etc.
- This may result in electric shock or injury.
Do not wash laundry contaminated by oils, creams or lotions usually found in skincare shops or massage clinics.
- This may result in the rubber seal becoming deformed and water leakage.
Do not leave metal objects such as a safety pin or hair pin, or bleach in the tub for long periods of time.
- This may cause the tub to rust.
- If rust starts appearing on the surface of the tub, apply a cleansing agent (neutral) to the surface and use a sponge to clean it. Never use a metal brush.
Do not use dry cleaning detergent directly and do not wash, rinse, or spin laundry contaminated by dry cleaning detergent.
- This may result in spontaneous combustion or ignition due to the heat of the oxidation of the oil.
Do not use hot water from water cooling/heating devices.
- This may result in problems with the washer.
Do not use natural hand-washing soap for the washer.
- If it hardens and accumulates inside the washer, it may result in problems with the product, discoloration, rust or bad odors.
Do not wash large laundry items such as bedding in the washing net.
- Place socks and brassieres into the washing net and wash them with the other laundry.
- Failing to do so may result in injury due to abnormal vibrations.
Do not use hardened detergent.
- If it accumulates inside the washer, it may result in water leakage.
SEVERE WARNING SIGNS FOR CLEANING
Do not clean the appliance by spraying water directly onto it. Do not use benzene, thinner or alcohol to clean the appliance.
- This may result in discoloration, deformation, damage, electric shock or fire.
Before cleaning or performing maintenance, unplug the appliance from the wall socket.
- Failing to do so may result in electric shock or fire.
safety information
WARNING
WF409ANW-02657D_EN.indd 10 2009-08-11 ø¿»ƒ 3:10:11
contents _11
contents
SETTING UP YOUR WASHER
12
12 Checking the parts 13 Meeting installation requirements
13 Electrical supply 13 Grounding 13 Water 14 Drain facility 14 Flooring 14 Location consideration 14 Alcove or closet installation
14 Installing your washer
WASHING A LOAD OF LAUNDRY
17
17 Loading your washer 17 Getting started 18 Overview of the control panel
20 Child lock 20 Garment+
20 My cycle 21 Steam 21 Washing clothes using the cycle selector
22 Detergent use 22 Features
CLEANING AND MAINTAINING YOUR
WASHER
24
24 Cleaning the exterior 24 Cleaning the interior 24 Cleaning the dispensers 25 Storing your washer 25 Cleaning the debris filter 26 Preserving the top cover and the front frame
TROUBLESHOOTING AND
INFORMATION CODES
27
27 Check these points if your washer… 29 Information codes
APPENDIX
31
31 Fabric care chart 32 Cycle chart 34 Helping the environment 34 Declaration of conformity 34 Specification
WARRANTY
35
35 Warranty
WF409ANW-02657D_EN.indd 11 2009-08-11 ø¿»ƒ 3:10:12
12_ setting up your new washing machine
setting up your washer
CHECKING THE PARTS
Unpack your washer and inspect it for shipping damage. Make sure you have received all of the items shown below. If your washer was damaged during shipping, or you do not have all of the items, contact 1-800-SAMSUNG(726-7864). To prevent personal injury or strain, wear protective gloves whenever lifting or carrying the unit.
Keep all packaging materials well out of the reach of children, as packaging materials can be dangerous to children.
- If a child places a bag over its head, it may result in suffocation.
Parts supplied
( use for the Upper Bolt Hole )
Wrench
Bolt hole covers Water supply hoses
Hose guide Plastic zip hose tie Manual book
Tools needed
Pliers Flat screwdriver
WARNING
Adjustable legs
Cold water supply hose
Hot water supply hose
Drain hose
Detergent drawer
Control panel
Door
Tub
Debris filter
Drain tube
Filter cover
Power cord
WF409ANW-02657D_EN.indd 12 2009-08-11 ø¿»ƒ 3:10:14
setting up your new washing machine _13
01 SETTING UP
MEETING INSTALLATION REQUIREMENTS
Electrical supply
120 Volt 60 Hz 15 AMP fuse or circuit breaker
Individual branch circuit serving only your washer is recommended.
Your washer is equipped with a power cord.
Never use an extension cord.
Grounding
ELECTRICAL GROUNDING IS REQUIRED ON THIS APPLIANCE.
This appliance must be grounded. In the event of malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current. This appliance is equipped with a power cord having a three-prong grounding plug for use in a properly installed and grounded outlet.
Improper connection of the equipment-grounding conductor can result in a risk of electrical shock. Check with a qualified electrician or serviceman if you are in doubt as to whether the appliance is properly grounded. Do not modify the plug provided with the appliance – if it does not fit the outlet, have a proper outlet installed by a qualified electrician.
IMPORTANT SAFETY PRECAUTIONS
To prevent unnecessary risk of fire, electrical shock or personal injury, all wiring and grounding must be done in accordance with the National Electrical Code ANSI/FNPA, No. 70 Latest Revision and local codes and ordinances. It is the personal responsibility of the appliance owner to provide adequate electrical service for this appliance.
Never connect ground wire to plastic plumbing lines, gas lines, or hot water pipes.
Water
To correctly fill your washer in the proper amount of time, water pressure of 20-116psi(137­800kPa) is required. Water pressure less than 20 psi(137kPa) may cause water valve failure, or may not allow the water valve to shut off completely. Or, it may extend the fill time beyond what your washer controls allow, resulting in your washer turning off. A time limit is built into the controls in the event of an internal hose becoming loose and flooding your home. The water faucets must be within 4 ft.(122cm) of the back of your washer for the inlet hoses provided with your washer.
Accessory inlet hoses are available in various lengths up to 10 ft.(305cm) for faucets that are further away from the back of your washer.
To avoid the possibility of water damage:
• Have water faucets easily accessible.
• Turn off faucets when the washer is not in use.
• Periodically check that there is no leakage from the water inlet hose fittings. Check all connections at the water valve and faucet for leaks.
WARNING
WARNING
WARNING
WARNING
WF409ANW-02657D_EN.indd 13 2009-08-11 ø¿»ƒ 3:10:14
14_ setting up your new washing machine
Drain facility
The recommended height of the standpipe is 18 in (46 cm). The drain hose must be routed through the drain hose clip to the standpipe. The standpipe must be large enough to accept the outside diameter of the drain hose. The drain hose is attached at the factory.
Flooring
For best performance, your washer must be installed on a solidly constructed floor. Wood floor may need to be reinforced to minimize vibration and/or unbalanced load situations. Carpeting and soft tile surfaces are contributing factors in vibration and may cause your washer to move slightly during the spin cycle.
Never install your washer on a platform or weakly supported structure.
Location consideration
Do not install your washer in areas where water may freeze, since your washer will always maintain some water in its water valve, pump, and hose areas. This can cause damage the pump, hoses and other components.
Alcove or closet installation
MINIMUM CLEARANCES FOR CLOSET AND ALCOVE INSTALLATIONS:
Sides – 1 In.(2.5 cm) Rear – 4 In.(10.2 cm)
Top – 17 In.(43.2 cm) Closet Front – 2 In.(5.1 cm)
If the washer and dryer are installed together, the closet front must have at least 72 in²(465 cm²) of an unobstructed air opening. Your washer alone does not require a specific air opening.
INSTALLING YOUR WASHER
STEP 1
Selecting a location
Before you install the washer, make sure the location:
• Has a hard, level surface without carpeting or flooring that may obstruct ventilation.
• Is away from direct sunlight.
• Has adequate ventilation.
• Will not be freezing (below 32 ˚F or 0 ˚C).
• Is away from heat sources such as oil or gas.
• Has enough space so that the washer doesn’t stand on its power cord.
setting up your washer
CAUTION
WF409ANW-02657D_EN.indd 14 2009-08-11 ø¿»ƒ 3:10:14
setting up your new washing machine _15
01 SETTING UP
STEP 2
Removing the shipping bolts
Before using your washer, you must remove the four shipping bolts from the back of the unit.
1. Loosen all the bolts with the supplied wrench.
2. Slide the bolt and spacer up and remove the bolt with
the spacer through the hole in the rear wall of your washer. Repeat for each bolt.
3. Fill the holes with the supplied bolt hole covers.
4. Keep the shipping bolts and spacers for future use.
STEP 3
Installing your washer
1.
Place the drain hose in the drain facility. Be sure an airtight connection is NOT made between the drain hose and the standpipe. The standpipe must be at least 18in.(46 cm) high.
Caution must always be exercised to avoid collapsing or damaging the drain hose. For best results, the drain hose should not be restricted in any way – by elbows, couplings, or excessive lengths. For situations where the drain hose cannot be conveniently elevated to at least 18in.(46 cm), the drain hose must be supported.
2. Before connect the inlet hoses to water faucets, check to ensure a washer is inside coupling.
96” Max
18” Min
96” Max
18” Min
Hose
retainer
Tie
strap
Laundry tub Stand pipe
Hose Guide
Rubber Washer
Coupling
WF409ANW-02657D_EN.indd 15 2009-08-11 ø¿»ƒ 3:10:16
16_ setting up your new washing machine
3. Check the inlet hose to ensure a washer is inside each fill hose.
Thread the inlet hoses to the HOT and COLD faucet connections. On the other end of the hose, check for one rubber washer per hose and install each fill hose to the water valve. Make sure the hose with the Hot printed line is attached to the HOT faucet. Tighten by hand until snug, then two-thirds of a turn with pliers.
For correct water use, connect both HOT and COLD water valves. If either or both are not connected, an “nF” (no fill) error can occur.
4. Turn on the HOT and COLD water supply and check all connections at the water valve and the faucet for leaks.
5. Plug the power cord into a 3-prong, well grounded 120 volt 60 Hz approved electrical outlet protected by a 15-amp fuse or comparable circuit breaker. Your washer is grounded through the third prong of the power cord when plugged into a three-prong grounded receptacle.
6. Slide your washer into position.
7. Level your washer by turning the leveling legs in or out as
necessary by hand or by using the wrench included with your washer. When your washer is level, tighten the locking nuts using the wrench or (-) flathead screwdriver.
Your washer must be leveled on all four sides. A carpenter’s level should be used on all four corners of your washer. It’s the best to recheck after the first dozen washes.
Avoid damage to the legs. Do not move the washer unless the locking-nuts are fastened to the bottom of the washer.
setting up your washer
Cold Hot
Cold printed Hot printed
Levelling Leg
Locking
Nut
WF409ANW-02657D_EN.indd 16 2009-08-11 ø¿»ƒ 3:10:18
washing a load of laundry _17
02 WASHING A LOAD OF LAUNDRY
washing a load of laundry
LOADING YOUR WASHER
You can fill the tub with dry, unfolded clothes; but DO NOT OVERLOAD the tub.
Overloading may reduce washing efficiency, cause excess wear, and possibly cause creasing or
wrinkling of the load.
Wash delicate items such as bras, hosiery, and other lingerie in the delicates cycle with similar lightweight items.
When washing big bulky items or a few smaller items that don’t fill the tub completely – a rug, a pillow, stuffed toys, or one or two sweaters, for example – add a few towels to improve tumbling and spin performance.
During the spin cycle, the washer may add additional water to redistribute the excessive imbalance inside the tub.
When washing heavily soiled loads, do not overload your washer in order to assure good cleaning results.
To add a forgotten item:
1. Press the Power button.
2. Press the Start/Pause button.
3. Wait for the door lock light to go out (Immediately).
4. Add the item, close the door, and press the Start/Pause button.
The door safety state continues for 15 seconds and the cycle is restarted.
To ensure thorough cleaning, add items within five minutes of starting the wash cycle.
Try washing bedding, towels, undergarments, and other articles that usually have close body contact using the ActivFresh™ Option, which sanitizes using cold water.
GETTING STARTED
1. Load your washer.
2. Close the door.
Push the laundry into the tub completely to prevent the laundry from being caught in the door or from falling out of the tub.
3. Press the Power button.
4. Add detergent and additives to the dispenser (See page 22~24).
5. Select the appropriate cycle and options for the load (See page 18~20).
6. Press the Start/Pause button.
7. The Wash Indicator will illuminate.
8. The estimated cycle time will appear in the display.
The time may fluctuate to better indicate the time remaining in the cycle.
The actual time required for a cycle may differ from the estimated time in the display depending on the water pressure, water temperature, detergent, and laundry.
9. Before your washer starts to fill, it will make a series of clicking noises to check the door lock and do a quick drain.
• When the cycle is complete, the door lock light will go out and “End” will appear in the display.
• DO NOT attempt to open the door until the door lock light is off. To add a forgotten item, see “Loading your washer” section (See page 17).
• When your washer is restarted after a pause, expect a delay of up to 15 seconds before the cycle continues.
• Pressing
Power button cancels the cycle and stops your washer.
The Wash, Rinse and Spin indicators will illuminate during those portions of the cycle.
CAUTION
WF409ANW-02657D_EN.indd 17 2009-08-11 ø¿»ƒ 3:10:19
18_ washing a load of laundry
OVERVIEW OF THE CONTROL PANEL
[ WF409 ]
[ WF407 ]
Cycle Selector
Select the appropriate cycle for the type of load. This will determine the tumble pattern and spin speed for the cycle.
To minimize wrinkling of your laundry, select the Perm Press cycle.
Normal - For most fabrics including cottons, linens, and normally soiled garments. Heavy Duty - For sturdy, colorfast fabrics and heavily soiled garments. Whites - For white fabrics with or without bleach.
Perm Press - For wash-and-wear, synthetic fabrics, and lightly to normally
soiled garments. Sanitize - For heavily soiled, colorfast garments. This cycle heats the water to 150°F(65.6°C) to eliminate bacteria.
If Pause is selected during the heating portion of the Sanitize cycle, your washer door will remain locked for your safety.
Bedding - For heavily soiled, colorfast garments, this cycle provides high washing temperature and steam and is efficient in cleaning stains. Deep steam - For bulky items such as blankets and sheets. When you are washing comforters, use liquid detergent. Delicates - For sheer fabrics, bras, lingerie silk, and other handwash-only fabrics. For best results, use liquid detergent.
Hand Wash - For handwashable, special care garments. Wool - For machine-washable wool. Loads should be under 8 pounds.
The Wool cycle washes laundry by moving the wash drum horizontally to maintain the characteristics of the wool fibers and to prevent damaging the cloth. It then stops for a while to allow the laundry to soak in the water. This stop operation is not a problem.
washing a load of laundry
3
1
2
6
5
4
7
8
9
1
3
1
2
6
5
4
7
8
9
WF409ANW-02657D_EN.indd 18 2009-08-11 ø¿»ƒ 3:10:20
washing a load of laundry _19
02 WASHING A LOAD OF LAUNDRY
It is recommended using a neutral detergent to prevent damage to the cloth and to improve the washing results.
The Wool cycle of this machine has been approved by Woolmark for the washing of machine washable Woolmark products provided that the products are washed according to the instructions on the garment label and those issued by the manufacturer of this washer, M0904.
Quick Wash
- For lightly soiled garments needed quickly.
Rinse + Spin - Use for loads that need rinsing only or to add rinse-added fabric softener to a load. Spin Only - Provides a spin to remove more water.
Digital graphic display
Displays the remaining cycle time, all cycle information, and error messages.
Wash
Option selection buttons
Press these buttons to select different cycle options. Pre Wash - To use this feature add detergent to the pre wash section of the detergent compartment. When turned on, the washer fills with cold water and detergent, tumbles, then drains and advances to the selected wash cycle. Some cycles cannot be selected with with this option (See page 32~33).
You cannot select the prewash option in the
Delicate, Wool, Quick
Wash, Hand Wash, Rinse+Spin, and Spin Only cycles.
Extra Rinse - Add an additional rinse at the end of the cycle to more thoroughly remove laundry additives and perfumes.
Extended Spin - Add additional time to remove more water from loads. Delay Start - Any cycle can be delayed for 1 to 24 hours in one-hour
i
ncrements. Displayed hour indicates the time at which the wash will be started.
My Cycle - Choose your favorite cycle including temperature, spin, soil level, option, etc. Steam - Press this button to use the Steam Wash function. Steam Wash is available
with Heavy Duty, Normal, Perm Press, Sanitize, Bedding cycles. For heavily soiled, colorfast garments, Steam Wash improves stain treatment and use less water of each cycle (See page 33).
Temperature selection button
Press the button repeatedly to cycle through the different water temperature options.
Extra Hot/Cold - Heavily soiled, colorfast items. Only available with the Sanitize cycle. Hot/Cold - Whites and heavily soiled, colorfast items. Warm/Warm - Colorfast items. When warm rinse is selected, only the final rinse will
be warm. The other rinses will be cold to conserve energy.
Warm/Cold - Moderately soiled, colorfast items; most wrinkle-free items. Cold/Cold - Brightly colored, very lightly soiled items.
Spin selection button
Press the button repeatedly to cycle through the different spin speed options. Extra High - Removes more water from loads during spin.
To minimize wrinkling of wrinkle-free and no-iron fabrics, DO NOT use the Extra High spin option for these loads, nor overload your washer.
High - Use for underwear, t-shirts, jeans and sturdy cottons. Medium - Use for jeans, wrinkle-free or wash-and-wear items and synthetics. Low - Use for delicate items needing a slow spin speed. No Spin - Drains your washer without spinning. Use for extremely delicate
items that cannot tolerate any spin.
Soil Level selection button
Press the button to select the soil level/washing time. (Heavy Normal Light) Heavy - For heavily soiled loads.
Normal - For moderately soiled loads. This setting is best for most loads.
Light - For lightly soiled loads.
2
4
5
3
6
WF409ANW-02657D_EN.indd 19 2009-08-11 ø¿»ƒ 3:10:20
20_ washing a load of laundry
washing a load of laundry
Signal selection button
Press the button to increase or decrease the end of cycle signal volume or turn off the signal. (Off Softer Louder)
Start/Pause selection button
Press to pause and restart programs.
Power button
Press once to turn your washer on, press again to turn your washer off. If the washer is left on for more than 10 minutes without any buttons being touched, the power automatically turns off.
Child lock
A function that prevents children from playing with your washer. Once the Child Lock function is activated, the control panel cannot be activated, preventing children from playing with the washer.
ACTIVATING/DEACTIVATING
If you want to activate/deactivate the Child Lock function, press the Soil Level and Signal buttons at the same time for 3 seconds.
How It works:
1. To activate or deactivate the Child Lock function, press and hold both the Soil level and Signal buttons for 3 seconds. Activation/Deactivating the Child Lock function is only available when the power is on.
2. When the Child Lock function is activated, and any button except for the Power button is pressed, the buzzer will sound for a short period and the “Child Lock” indicator will turn off for 10 seconds.
3. The Child Lock function stays on even after the power has been turned on and off or the power cord has been disconnected and reconnected.
When buttons, other than the Power button, do not respond, please check if the Child Lock function is on.
Garment+
You can add or take out laundry items even after the wash has started, as long as the “Garment+ ” light is turned on. Pressing the Start/Pause button unlocks the door, unless the water is too hot or if there is too much water in your washer. If you are able to unlock the door and wish to continue the wash cycle, close the door and press the Start/Pause button.
My cycle
Allows you to activate your custom wash (temperature, spin, soil level, etc.) with one–button convenience. By pushing the My Cycle button, you activate the settings used during the My Cycle mode. The “My Cycle” light will indicate activation. You can select all options as follows in the My Cycle mode.
1. Select cycle using the Cycle Selector.
2. After cycle selection, set each option.
See page 32 for available option settings with each cycle.
3. Then, you can store the cycle and options you select by pressing the Start/Pause button in the My Cycle mode. The cycle and options you select will be displayed the next time you choose the My Cycle function.
You can change the My Cycle settings by repeating the same process above. The last used setting will be displayed the next time you choose the My Cycle function.
7
8
9
WF409ANW-02657D_EN.indd 20 2009-08-11 ø¿»ƒ 3:10:21
washing a load of laundry _21
02 WASHING A LOAD OF LAUNDRY
Steam
The Steam Wash function injects steam directly into the laundry in the wash tub to increase the wash temperature and enhance the soak effect, thus improving the wash performance.
1. Load the washer.
2. Press the Power button.
3. Turn the Cycle Selector and select a steam cycle. (The Deep Steam cycle automatically
selects the Steam Wash function.)
4. Press the Steam button.
5. Add detergent into the dispenser tray for a wash, and add fabric softener up to the marked
line.
6. Press the Start/Pause button. : The washer automatically selects the optimal wash conditions by sensing the weight of the laundry.
If steam wash is selected, steam is injected at the most effective time for the detected amount of laundry in order to maximize the effect of the steam.
Washing clothes using the cycle selector
Your new washer makes washing clothes easy, using Samsung’s “Fuzzy Control” automatic control system. When you select a wash program, the machine will set the correct temperature, washing time, and washing speed.
1. Almost no customers will have the washer hooked up via the sink’s tap.
2. Press the Power button.
3. Open the door.
4. Load the articles of clothing one at a time loosely into the tub, without overfilling it.
5. Close the door.
6. Add detergent, softener, and pre-wash detergent (if necessary) into the appropriate
compartments.
Pre-wash is only available when selecting the
Normal, Perm Press, Sanitize, Bedding,
Whites(WF409*), Deep Steam(WF407*) and Heavy Duty cycles. It is only necessary if your
clothing is heavily soiled(WF409* See page 32, WF407* See page 33).
7. Use the Cycle Selector to select the appropriate cycle according to the type of material: The relevant indicators will illuminate on the control panel.
8. At this time, you can control the wash temperature, the number of rinse cycles, the spinning speed, and the delay time by pressing the appropriate
Option button.
9. Press the Start/Pause button on the Cycle Selector and the wash will begin. The process
indicator will light up and the remaining time for the cycle will appear in the display.
Pause Option
To unlock the door when the “Garment+” light is turned on, press the Start/Pause button.
1. Within 5 minutes of starting a wash, you can still add/remove laundry items to the wash.
2. Press the Start/Pause button to unlock the door.
3. The door cannot be opened when the water is too HOT or the water level is too HIGH.
4. After closing the door, press the Start/Pause button to restart the wash.
When the cycle is finished:
When the cycle is complete, “End” is displayed and the power remains on. The power is turned off in the following two cases.
1. When the Power button is pressed.
2. If the door is opened when “End” is displayed.
WF409ANW-02657D_EN.indd 21 2009-08-11 ø¿»ƒ 3:10:21
22_ washing a load of laundry
washing a load of laundry
DETERGENT USE
Your washer is designed to use high efficiency (HE) detergents.
For best cleaning results, use a high efficiency detergents such as Tide HE, Wisk HE, Cheer HE or Gain HE*. High efficiency detergents contain suds suppressors that reduce or eliminate suds. When fewer suds are produced, the load tumbles more efficiently and cleaning is maximized.
Regular detergent is not recommended. Please use HE detergents only.
Reducing the amount of detergent may reduce the cleaning quality. It is important to pre–treat stains, sort carefully by color and soil level, and avoid overloading.
* Brand names are trademarks of their respective manufacturers.
FEATURES
Automatic dispenser
Your Washer has separate compartments for dispensing detergent and color-safe bleach, chlorine bleach, and fabric softener. All laundry additives are added to their respective compartments before starting your Washer. The automatic dispenser MUST ALWAYS be in place before starting your Washer. DO NOT open the automatic dispenser when your washer is running. To use:
1. Never exceed the manufacturer’s recommendations when adding detergent.
2. This compartment holds liquid detergent for the main wash cycle, which is added to the load at beginning of cycle.
When using powdered detergent, remove the detergent liquid from the compartment. Powdered detergent will not dispense with detergent liquid.
Detergent compartment
1. Pour the recommended amount of laundry detergent directly into the detergent compartment before starting your washer.
2. If color-safe bleach is to be used, it should be added with detergent to the detergent compartment.
When adding color-safe bleach with detergent, it is best if both laundry products are in the same form – granular or liquid.
Pre wash compartment
Detergent Liquid
CAUTION
WF409ANW-02657D_EN.indd 22 2009-08-11 ø¿»ƒ 3:10:22
washing a load of laundry _23
02 WASHING A LOAD OF LAUNDRY
Pre Wash compartment
When using the Pre Wash option, detergent should be added to both the Pre Wash compartment and the detergent compartment. The detergent will automatically be dispensed during Pre Wash.
If high efficiency (HE) detergent is used, add 1/3 of the recommended amount to the Pre Wash compartment and 2/3 of the recommended amount to the detergent compartment.
Bleach compartment
(Liquid chlorine bleach only)
1. Add chlorine bleach to the bleach compartment. DO NOT exceed the MAX FILL line.
2. Avoid splashing or over–filling the compartment.
3. Your washer automatically dispenses bleach into the tub at
the appropriate time.
4. The dispenser automatically dilutes liquid chlorine bleach before it reaches the wash load.
• Never pour undiluted liquid chlorine bleach directly onto the load or into the tub. It is a powerful chemical and can cause fabric damage, such as weakening of the fibers or color loss, if not used properly.
• If you prefer to use color–safe, non–chlorine bleach, add it to the appropriate detergent compartment. DO NOT pour color–safe bleach into the Bleach compartment.
Fabric softener compartment
1. Pour the recommended amount of liquid fabric softener into the softener compartment. For smaller loads, use less than one capful.
2. Fabric softener should be diluted with water until it reaches MAX FILL in the compartment.
3. The dispenser automatically releases liquid fabric softener at the proper time during the rinse
cycle.
• Use the softener compartment ONLY for liquid fabric softeners.
• DO NOT use a Downy Ball* in the Fabric softener compartment of this washer. It will not add fabric softener at the appropriate time. Use the detergent compartment.
* Brand names are trademarks of their respective manufacturers.
Fabric Softener
compartment
Bleach
compartment
WF409ANW-02657D_EN.indd 23 2009-08-11 ø¿»ƒ 3:10:22
Loading...
+ 53 hidden pages