Samsung WF405ATPAWR/AA, WF405ATPASU/AA, WF405ATPASU/A2, WF398ATPAWR/A2 User Manual

Washing Machine

user manual

WF405ATPA** WF398ATPA**

WF397UTPA**

This manual is made with 100% recycled paper.

Imagine the possibilities

Thank you for purchasing this Samsung product.

WF405ATPA-03145A-09_EN.indd 1 2014-2-24 11:32:51

key features of your new PowerFoam™ washer

1. Extra Large Capacity

Samsung’s extra-large capacity laundry machine can wash a full set of your bedding, a kingsize comforter, or up to 28 bath towels in a single load. Since you don’t have to do as many loads, you save time, money, water, and energy.

2. PowerFoam™

Samsung’s eective PowerForm delivers improved cleanliness with advanced fabric care. PowerFoam allows detergent to disperse evenly and penetrate fabrics faster and deeper.

3. SpeedSpray™

Samsung’s new SpeedSpray technology saves you time by shortening wash times while still keeping all portions of the washing process and getting your clothes clean.

SpeedSpray performs in Normal, Bedding PLUS, Deep Steam, Stain Away and Eco Cold cycle and the saving time may vary by cycles and various load and option compositions.

4. Smart Care

Samsung’s Smart Care, an automatic error-monitoring system, detects and diagnoses problems at an early stage and provides quick and easy solutions.

5. VRT™ (Vibration Reduction Technology)

This Samsung washer performs smoothly at top spin speeds, minimizing noise and vibration.

6. Pure Cycle™ (Tub Cleaning cycle)

Clean your drum with one button! Pure Cycle is specially designed to remove detergent residue and dirt buildup in the tub, diaphragm, and on the door glass without the need for special chemical detergents.

7. Deep steam

The Deep Steam feature boosts cleaning performance and loosens grime and dirt, providing superior cleaning results.

8. Diamond drum™

Takes gentle care of your fabrics. With inside holes 36 % smaller than those of conventional drums,the diamond drum prevents fabrics from sticking out through the holes and consequently being damaged.

9. Woolmark Certiﬁed

The machine wash wool cycle on Samsung machines has been tested and has passed the required Woolmark Company speciﬁcation for machine washable wool products. Fabrics should be washed according to the instructions on the garment label as speciﬁed by Woolmark and Samsung.

10. Digital display & Center jog dial

The jog dial enables you to select cycles in both directions with ease, and the display is easy to use and understand.

11. DD Motor

The power to handle anything! Our direct-drive inverter motor delivers power right to the washer tub from a variable speed, reversible motor. A beltless direct-drive motor generates a higher spin speed of 1200 rpm for more eective, quiet operation. The washer also has fewer moving parts, meaning fewer repairs.

2_ key features of your new PowerFoam™ washer

WF405ATPA-03145A-09_EN.indd 2 2014-2-24 11:32:52

12. Sanitize

When you select the NSF certiﬁed Sanitize cycle, the water heats to an extra high temperature and removes 99.9 % of certain bacteria typically found on clothing, bedding, or towels. This certiﬁcation is awarded by NSF International, an independent third-party testing and certiﬁcation organization.

Please check the garment care label to avoid garment damage. Only sanitizing cycles have been designed to meet the requirements of this protocol for sanitization ecacy.

Sanitization Performance of Residential and Commercial, Family-Sized Clothes Washers

NSF Protocol P172

13. Pedestal with Storage Drawers (Model No : WE357*)

An optional 15” pedestal is available to raise the washer for easier loading and unloading. It also oers a built-in storage drawer that can hold a 100 oz. bottle of detergent

14. Stacking (Model No : SK-3A1/XAA, SK-4A/XAA, SK-5A/XAA)

Samsung washers and dryers can be stacked to maximize usable space. An optional stacking kit is available for purchase from your Samsung retailer.

key features of your new PowerFoam™ washer _3

WF405ATPA-03145A-09_EN.indd 3 2014-2-24 11:32:53

safety information

Congratulations on your new Samsung washer. This manual contains important information on the installation, use, and care of your appliance. Please take time to read this manual to take full advantage of your washer’s many beneﬁts and features.

WHAT YOU NEED TO KNOW ABOUT SAFETY INSTRUCTIONS

Warnings and Important Safety Instructions in this manual do not cover all possible conditions and situations that may occur. It is your responsibility to use common sense, caution, and care when installing, maintaining, and operating your washer.

IMPORTANT SAFETY SYMBOLS AND PRECAUTIONS

What the icons and signs in this user manual mean:

Hazards or unsafe practices that may result in severe personal injury or death.

WARNING

CAUTION

To reduce the risk of ﬁre, explosion, electric shock, or personal injury when using your washer, follow these basic safety precautions:

Hazards or unsafe practices that may result in minor personal injury or property damage.

Do NOT attempt.

Do NOT disassemble.

Do NOT touch.

Follow directions explicitly.

Unplug the power plug from the wall socket.

Make sure the machine is grounded to prevent electric shock.

Call the service center for help.

Note

These warning signs are here to prevent injury to you and others. Please follow them explicitly. After reading this section, keep it in a safe place for future reference.

Read all instructions before using the appliance.

SAVE THESE INSTRUCTIONS

4_ Safety information

WF405ATPA-03145A-09_EN.indd 4 2014-2-24 11:32:53

WARNING: To reduce the risk of ﬁre, electric shock, or injury to persons when using your appliance, follow basic precautions, including the following:

WARNING

1. Read all instructions before using the appliance.

2. Do not wash or dry articles that have been previously cleaned in, washed in, soaked in, or spotted with gasoline, dry-cleaning solvents, other ﬂammable or explosive substances as they give o vapors that could ignite or explode.

3. Do not allow children to play on or in the appliance. Close supervision of children is necessary when the appliance is used near children.

4. Before the appliance is removed from service or discarded, remove the door to the washing or drying compartment.

5. Do not reach into the appliance if the drum is moving.

6. Do not install or store this appliance where it will be exposed to the weather.

7. Do not tamper with controls.

8. Do not repair or replace any part of the appliance or attempt any servicing unless speciﬁcally recommended in the user-maintenance instructions or in published userrepair instructions that you understand and have the skills to carry out.

9. Do not add gasoline, dry-cleaning solvents, or other ﬂammable or explosive substances to the wash water. These substances give o vapors that could ignite or explode.

10.Under certain conditions, hydrogen gas may be produced in a hot water system that has not been used for 2 weeks or more. HYDROGEN GAS IS EXPLOSIVE. If the hot water system has not been used for such a period, before using a washer or combination washer-dryer, turn on all hot water faucets and let the water ﬂow from each for several minutes. This will release any accumulated hydrogen gas. As the gas is ﬂammable, do not smoke or use an open ﬂame during this time.

State of California Proposition 65 Warnings:

WARNING

WARNING:This product contains chemicals known to the State of California to cause cancer and reproductive toxicity.

SAVE THESE INSTRUCTIONS

Safety information _5

WF405ATPA-03145A-09_EN.indd 5 2014-2-24 11:32:54

safety information

SEVERE WARNING SIGNS FOR INSTALLATION

WARNING

Plug the power cord into an AC 120 V / 60 Hz / 15 A wall socket or higher and use the socket for this appliance only. In addition, do not use an extension cord.

- Sharing a wall socket with other appliances using a power strip or extending the power cord may result in electric shock or ﬁre.

- Do not use an electric transformer. It may result in electric shock or ﬁre.

- Ensure that the power voltage, frequency and current are the same as those of the product speciﬁcations. Failing to do so may result in electric shock or ﬁre.

The installation of this appliance must be performed by a qualiﬁed technician or service company.

- Failing to do so may result in electric shock, ﬁre, an explosion, problems with the product, or injury.

Remove all foreign substances such as dust or water from the power plug terminals and contact points using a dry cloth on a regular basis.

- Unplug the power plug and clean it with a dry cloth.

- Failing to do so may result in electric shock or ﬁre.

Plug the power plug into the wall socket in the right direction so that the cord runs towards the ﬂoor.

- If you plug the power plug into the socket in the opposite direction, the electric wires within the cable may be damaged and this may result in electric shock or ﬁre.

This appliance must be properly grounded. Do not ground the appliance to a gas pipe, plastic water pipe, or telephone line.

- This may result in electric shock, ﬁre, an explosion, or problems with the product

- Never plug the power cord into a socket that is not grounded correctly and make sure that it is in accordance with local and national codes.

Do not install this appliance near a heater or inﬂammable material. Do not install this appliance in a humid, oily or dusty location, in a location exposed to direct sunlight and water (rain drops). Do not install this appliance in a location where gas may leak.

- This may result in electric shock or ﬁre.

Plug the power plug into the wall socket ﬁrmly. Do not use a damaged power plug, damaged power cord or loose wall socket.

- This may result in electric shock or ﬁre.

Do not pull or excessively bend the power cord. Do not twist or tie the power cord. Do not hook the power cord over a metal object, place a heavy object on the power cord, insert the power cord between objects, or push the power cord into the space behind the appliance.

- This may result in electric shock or ﬁre.

Do not pull the power cord when unplugging the power plug.

- Unplug the power plug by holding the plug.

- Failing to do so may result in electric shock or ﬁre.

SAVE THESE INSTRUCTIONS

6_ Safety information

WF405ATPA-03145A-09_EN.indd 6 2014-2-24 11:32:54

When the power plug or power cord is damaged, contact your nearest service center.

CAUTION SIGNS FOR INSTALLATION

CAUTION

This appliance should be positioned in such a way that it is accessible to the power plug.

- Failing to do so may result in electric shock or ﬁre due to electric leakage. Install your appliance on a level and hard ﬂoor that can support its weight.

- Failing to do so may result in abnormal vibrations, noise, or problems with the product.

Unplug the power plug when the appliance is not being used for long periods of time or during a thunder/lightning storm.

- Failing to do so may result in electric shock or ﬁre.

SEVERE WARNING SIGNS FOR USING

WARNING

If the appliance is ﬂooded, cut the power immediately and contact your nearest service center. If the appliance generates a strange noise, a burning smell or smoke, unplug the power plug immediately and contact your nearest service center.

- Failing to do so may result in electric shock or ﬁre. In the event of a gas leak (such as propane gas, LP gas, etc.), ventilate immediately without

touching the power plug. Do not touch the appliance or power cord.

- Do not use a ventilating fan.

- A spark may result in an explosion or ﬁre. Do not wash items contaminated with gasoline, kerosene, benzene, paint thinner, alcohol or

other ﬂammable or explosive substances.

- This may result in electric shock, ﬁre or an explosion. Do not open the washer door by force while it is operating (high-temperature washing/

drying/spinning).

- Water ﬂowing out of the washer may result in burns or cause the ﬂoor to be slippery. This may result in injury.

- Opening the door by force may result in damage to the product or injury.

Make sure to remove the packaging (sponge, styrofoam) attached to the bottom of the washer before using it.

Do not insert your hand under the washer.

- This may result in injury.

SAVE THESE INSTRUCTIONS

Safety information _7

WF405ATPA-03145A-09_EN.indd 7 2014-2-24 11:32:54

safety information

Do not touch the power plug with wet hands.

- This may result in electric shock. Do not turn the appliance o by unplugging the power plug while an operation is in

progress.

- Plugging the power plug into the wall socket again may cause a spark and result in electric shock or ﬁre.

Keep all packaging materials well out of the reach of children, as packaging materials can be dangerous to children.

- If a child places a bag over its head, it may result in suocation.

Do not let children or inﬁrm persons use this washer unsupervised.

- Failing to do so may result in electric shock, burns or injury.

Do not insert your hand or a metal object under the washer while it is operating.

- This may result in injury.

Make sure the detergent drawer is closed before you put laundry into the washer or remove laundry from the washer.

- If the detergent drawer is open, you could strike the drawer with your head and injure yourself.

Do not attempt to repair, disassemble, or modify the appliance yourself.

- Do not use any fuse(such as cooper, steel wire, etc.) other than the standard fuse.

- When repairing or reinstalling the appliance is required, contact your nearest service center.

- Failing to do so may result in electric shock, ﬁre, problems with the product, or injury.

If any foreign substance such as water has entered the appliance, unplug the power plug and contact your nearest service center.

- Failing to do so may result in electric shock or ﬁre.

When the water supply hose comes loose from the faucet and ﬂoods the appliance, unplug the power plug.

- Failing to do so may result in electric shock or ﬁre.

If any foreign substance enters the appliance, unplug the power plug and contact you nearest service center.

- Failing to do so my result in electric shock or ﬁre.

SAVE THESE INSTRUCTIONS

8_ Safety information

WF405ATPA-03145A-09_EN.indd 8 2014-2-24 11:32:54

CAUTION SIGNS FOR USING

CAUTION

When the washer is contaminated by a foreign substance such as detergent, dirt, food waste, etc., unplug the power plug and clean the washer using a damp and soft cloth.

- Failing to do so may result in discoloration, deformation, damage or rust. The front glass may be broken by a strong impact. Take care when using the washer.

- When the glass is broken, it may result in injury. After a water supply failure or when reconnecting the water supply hose, open the faucet

slowly. Open the faucet slowly after a long period of non-use.

- The air pressure in the water supply hose or the water pipe may result in damage to a part or in water leakage.

If a drain error occurs during an operation, check if there is a draining problem.

- If the washer is used when it is ﬂooded because of a draining problem, it may result in electric shock or ﬁre due to electric leakage.

Insert the laundry into the washer completely so that laundry does not get caught in the door.

- If laundry gets caught in the door, it may result in damage to the laundry or the washer, or result in water leakage.

Ensure that the faucet is turned o when the washer is not being used.

- Ensure that the screw on the water supply hose connector is properly tightened.

- Failing to do so may result in property damage or injury.

Take care that the Rubber Seal and the Front Door Glass are not contaminated by a foreign substance (e.g. waste, thread, hair, etc.)

- If a foreign substance is caught in the door or the door is not completely closed, it may cause a water leakage.

Open the faucet and check if the water supply hose connector is ﬁrmly tightened and that there is no water leaking before using the product.

- If the screws or the water supply hose connector are loose, it may result in water leakage.

The product you have purchased is designed for domestic use only. The use for business purposes qualiﬁ es as product misuse. In this case, the product will not be covered by the standard warranty provided by Samsung and no responsibility can be attributed to Samsung for malfunctions or damages resulting from such misuse.

If the wash is not started and the laundry is left for a period of time after you have added detergent or applied stain remover or pre-treatment onto the laundry, the laundry may be discolored.

Select the recommended cycle and temperature on the basis of the laundry items, sort the laundry by color on the basis of its colorfastness and select the appropriate cycle.

Make sure that foreign objects such as pins, buttons and coins are removed from clothing items when adding laundry to the washer. Wash dirty laundry separately from relatively clean items and wash fragile items separately from tougher textiles.

If an item is stained, wash it as soon as possible. Use stain remover or detergent only after testing the colorfastness of the item by applying a small quantity to an inside seam.

SAVE THESE INSTRUCTIONS

Safety information _9

WF405ATPA-03145A-09_EN.indd 9 2014-2-24 11:32:54

safety information

Do not stand on top of the appliance or place objects (such as laundry, lighted candles, lighted cigarettes, dishes, chemicals, metal objects, etc.) on the appliance.

- This may result in electric shock, ﬁre, problems with the product, or injury. Do not operate the appliance with wet hands.

- This may result in electric shock. Do not spray volatile material such as insecticide onto the surface of the appliance.

- As well as being harmful to humans, it may also result in electric shock, ﬁre or problems with the product.

Do not place an object that generates a electromagnetic ﬁeld near the washer.

- This may result in injury due to a malfunction.

Since the water drained during a high-temperature wash or drying cycle is hot, do not touch the water.

- This may result in burns or injury.

Do not wash, spin or dry water-proof seats, mats or clothing (*).

- Do not wash thick, hard mats even if the washer mark is on the care label.

- This may result in injury or damage to the washer, walls, ﬂoor or clothing due to abnormal vibrations.

* Woolen Bedding PLUS, rain covers, ﬁshing vests, ski pants, sleeping bags, diaper

covers, sweat suits, and bicycle, motor cycle, car covers, etc.

Do not operate the washer when the detergent box is removed.

- This may result in electric shock or injury due to water leakage.

Do not touch the inside of the tub during or just after drying as it is hot.

- This may result in burns.

Do not insert your hand into the detergent dispenser after opening it.

- This may result in injury as your hand may be caught.

Do not place any objects (such as shoes, food waste, animals) other than laundry into the washer.

- This may result in damage to the washer, or injury and death in the case of pets due to the abnormal vibrations.

Do not press the buttons using sharp objects such as pins, knifes, ﬁngernails, etc.

- This may result in electric shock or injury.

Do not wash laundry contaminated by oils, creams or lotions usually found in skincare shops or massage clinics.

- This may result in the rubber seal becoming deformed and water leakage.

Do not leave metal objects such as a safety pin or hair pin, or bleach in the tub for long periods of time.

- This may cause the tub to rust.

- If rust starts appearing on the surface of the tub, apply a cleansing agent (neutral) to the surface and use a sponge to clean it. Never use a metal brush.

SAVE THESE INSTRUCTIONS

10_ Safety information

WF405ATPA-03145A-09_EN.indd 10 2014-2-24 11:32:54

Do not use dry cleaning detergent directly and do not wash, rinse, or spin laundry contaminated by dry cleaning detergent.

- This may result in spontaneous combustion or ignition due to the heat of the oxidation of the oil.

Do not use hot water from water cooling/heating devices.

- This may result in problems with the washer.

Do not use natural hand-washing soap for the washer.

- If it hardens and accumulates inside the washer, it may result in problems with the product, discoloration, rust or bad odors.

Do not wash large laundry items such as Bedding PLUS in the washing net.

- Failing to do so may result in injury due to abnormal vibrations.

- Place smaller items, such as lace socks and lingerie in the washing net.

Do not use hardened detergent.

- If it accumulates inside the washer, it may result in water leakage.

Do not wash throw rugs or doormats.

- If you wash throw rugs or doormats, the sand will accumulate inside the washer. It may result in error such as no draining.

Take care that children’s ﬁngers are not caught in the door when closing it. This may result in injury.

SEVERE WARNING SIGNS FOR CLEANING

WARNING

Do not clean the appliance by spraying water directly onto it. Do not use the strong acid cleaning agent. Do not use benzene, thinner or alcohol to clean the appliance.

- This may result in discoloration, deformation, damage, electric shock or ﬁre.

Before cleaning or performing maintenance, unplug the appliance from the wall socket.

- Failing to do so may result in electric shock or ﬁre.

SAVE THESE INSTRUCTIONS

Safety information _11

WF405ATPA-03145A-09_EN.indd 11 2014-2-24 11:32:55

contents

INSTALLING YOUR WASHER

OPERATING INSTRUCTIONS

WASHING A LOAD OF LAUNDRY

MAINTAINING YOUR WASHER

TROUBLESHOOTING

13 Unpacking your washer 13 Overview of your washer

14 Electrical 14 Grounding 14 Water 15 Drain facility 15 Flooring 15 Location considerations 15 Alcove or closet installation 15 Undercounter installation (washer only) 16 With optional pedestal base or stacking kit

17 Important note to installer

17 Installation ﬂow chart

20 Loading your washer 20 Washing clothes: Basic Instructions

21 Overview of the control panel

23 Child Lock 24 Spin Only 24 Garment+ 24 Delay Start 25 My Cycle 25 Smart Care 26 DEEP STEAM 26 Washing clothes using the cycle selector

27 Using steam wash 27 ATC (Auto Temperature Control) 28 Detergent use 28 Features

30 Cleaning the exterior 30 Cleaning the interior 30 Cleaning the dispensers 30 Storing your washer 31 Cleaning the debris ﬁlter 32 Cleaning the door seal/bellow 32 Preserving the top cover and the front frame 33 Pure Cycle™

34 Check these solutions if your washer… 36 Information codes

APPENDIX

12_ Contents

WF405ATPA-03145A-09_EN.indd 12 2014-2-24 11:32:56

38 Fabric care chart 39 Cycle chart 41 Helping the environment 41 Declaration of conformity 41 Speciﬁcation

installing your washer

UNPACKING YOUR WASHER

Unpack your washer and inspect it for shipping damage. Make sure you have received all the items shown below. If your washer was damaged during shipping, or you do not have all of the items, contact 1-800-SAMSUNG (726-7864).

To prevent personal injury or strain, wear protective gloves whenever lifting or carrying the unit.

Packing materials can be dangerous to children. Keep all packing material (plastic bags, polystyrene, etc.) well out of the reach of children.

WARNING

OVERVIEW OF YOUR WASHER

01 Installing your washer

Detergent drawer

Control panel

Door

Tub

Debris ﬁlter

Drain tube

Filter cover

Hot water supply

hose

Cold water supply hose

Drain Hose

Adjustable legs

Wrench Bolt Hole Covers Water Supply Hoses Hose Guide

Plastic Zip Hose Tie

* Bolt hole covers : The number of bolt hole covers depends on the model (3~6 covers).

Installing your washer _13

WF405ATPA-03145A-09_EN.indd 13 2014-2-24 11:32:58

installing your washer

BASIC LOCATION REQUIREMENTS

Electrical

• 120 Volt 60 Hz 15 AMP fuse or circuit breaker

• Individual branch circuit serving only your washer is recommended.

• Your washer is equipped with a power cord.

NEVER USE AN EXTENSION CORD.

CAUTION

Grounding

ELECTRICAL GROUNDING IS REQUIRED FOR THIS APPLIANCE.

This appliance must be grounded. In the event of malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current.

This appliance is equipped with a power cord having a three-prong grounding plug for use in a properly installed and grounded three-prong outlet.

The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.

An improperly connected equipment-grounding conductor can increase the risk of electrical shock. Check with a qualiﬁed electrician or serviceman if you are not sure whether the

WARNING

appliance is properly grounded. Do not modify the plug provided with the appliance – if it does not ﬁt the outlet, have a proper outlet installed by a qualiﬁed electrician.

IMPORTANT SAFETY PRECAUTIONS

• To prevent unnecessary risk of ﬁre, electrical shock or personal injury, all wiring and grounding must be done in accordance with the National Electrical Code ANSI/FNPA, No. 70 Latest Revision and local codes and ordinances. It is the personal responsibility of the appliance owner to provide adequate electrical service for this appliance.

NEVER CONNECT THE GROUND WIRE TO PLASTIC PLUMBING LINES, GAS LINES, OR HOT WATER PIPES.

CAUTION

Water

Using bad quality water may cause the water supply valve to operate abnormally. To correctly ﬁll your washer in the proper amount of time, water pressure of 20-116 psi (137-

800kPa) is required. Water pressure less than 20 psi may cause water valve failure, may not allow the water valve to

shut o completely, or may extend the ﬁll time beyond what your washer controls allow, causing your washer to turn o. A time limit is built into the controls to prevent extensive ﬂooding in your home if an internal hose becomes loose.

The water faucets must be within 4 feet / 122 cm of the back of your washer to match the inlet hoses provided with your washer.

Accessory inlet hoses are available in various lengths up to 10 feet/305 cm for faucets that are further away from the back of your washer.

To avoid the possibility of water damage:

• Have water faucets easily accessible

• Turn o faucets when the washer is not in use.

• Periodically check that there is no leakage from the water inlet hose ﬁttings.

CHECK ALL CONNECTIONS AT THE WATER VALVE AND FAUCET FOR LEAKS.

WARNING

14_ Installing your washer

WF405ATPA-03145A-09_EN.indd 14 2014-2-24 11:32:59

Drain facility

The recommended height of the standpipe is 18 in/46 cm. The drain hose must be routed through the drain hose clip to the standpipe. The standpipe must be large enough to accept the outside diameter of the drain hose. The drain hose is attached at the factory.

Flooring

For best performance, you must install your washer on a solidly constructed ﬂoor. Wood ﬂoors may need to be reinforced to minimize vibration and/or unbalanced load situations. Carpeting and soft tile surfaces are contributing factors to vibration which can cause your washer to move slightly during the spin cycle.

Never install your washer on a platform or weakly supported structure.

Location considerations

Do not install your washer in areas where water may freeze, since your washer will always retain some water in its water valve, pump, and hose areas. Freezing water can damage the belts,the pump, hoses and other components.

Alcove or closet installation

MINIMUM CLEARANCES FOR CLOSET AND ALCOVE INSTALLATIONS:

Sides – 1 in / 25 mm Rear – 5.9 in / 150 mm If the washer and dryer are installed together, the closet front must have at least a 72 in² (465

cm²) unobstructed air opening. Your washer alone does not require a speciﬁc air opening. A. Recessed area

Top – 17 in / 432 mm Closet Front – 2 in / 51 mm

01 Installing your washer

1 in.

(2.5 cm)

1 in.

(2.5 cm)

B. Side view - closet or conﬁned area

Undercounter installation (washer only)

27 in.

(68.6 cm)

40 in.

(101.6 cm)

27 in.

(68.6 cm)

1 in.

(2.5 cm)

(5 cm)

2 in.

17 in.

(43.2 cm)

32.3 in. (82 cm)

5.9 in.

(15 cm)

1 in.

(2.5 cm)

27 in.

(68.6 cm)

1 in.

(2.5 cm)

Installing your washer _15

WF405ATPA-03145A-09_EN.indd 15 2014-2-24 11:33:00

installing your washer

With optional pedestal base or stacking kit

Required Dimensions for Installation With Pedestal

51.7 in. (131.4 cm) to clear open door

3 in.

(7.6 cm)

5.9 in.

(15 cm)

27 in.

(68.6 cm)

48 in.² *

(310 cm²)

341.1 in.

(86.5 cm)

38.7in.

(98.4cm)

53.3 in.

(135.5 cm)

5 in.

(12.7 cm)

24 in.² *

(155 cm²)

Closet or Door

3 in.

(7.6 cm)

1 in.

(2.5 cm)

(82 cm)

Required Dimensions for Installation With Stacking Kit

6 in. *

(15.2 cm)

77.5 in.

(196.8 cm)

* Required spacing

1 in.

(2.5 cm)

27 in.

(68.6 cm)

** External exhaust elbow requires

additional space.

32.3 in.

5.9 in.** (15 cm)

16_ Installing your washer

WF405ATPA-03145A-09_EN.indd 16 2014-2-24 11:33:02

IMPORTANT NOTE TO INSTALLER

Please read the following instructions carefully before installing the washer. These instructions should be retained for future reference. We recommend you hire a professional to install this washer.

Installation ﬂow chart

01 Installing your washer

Selecting a

location

Please

check again

before

steps.

Yes

Adjusting the

levelling feet

have excess vibration

Removing the shipping

bolts (*Drum only)

Does

your washer

or noise?

Connecting the water

Powering your washing

machine

Running a Calibration mode

(Refer to the following

description)

and the drain

[Running a test cycle]

Run a test cycle (Rinse+Spin) with

small amount of laundary

STEP 1

Removing the Shipping Bolts

Before using your washer, you must remove all shipping bolts from the back of the unit.

1. Loosen all the bolts with the supplied wrench.

2. Slide the bolt and spacer up and remove the bolt with the spacer

through the hole in the rear wall of your washer. Repeat for each bolt.

3. Cover the holes with the supplied Bolt Hole Covers (See page 13).

4. Keep the shipping bolts and spacers for future use.

(about 4~5 Towels)

Finish the

installation

STEP 2 Selecting a Location

Before you install your washer, make sure the location:

• Has a hard, level surface

• Is away from direct sunlight

• Has adequate ventilation

• Will not freeze (tempuratures are never below 32 °F or 0 °C).

• Is away from heat sources such as oil or gas

• Has enough room for the power cord.

• Doesn’t have any carpeting that will obstruct ventilation openings.

Installing your washer _17

WF405ATPA-03145A-09_EN.indd 17 2014-2-24 11:33:03

installing your washer

1RPRUHWKDQ

ರFP

+RVH*XLGH

STEP 3

Installing your Washer

1. If you use a stand pipe, make sure the connection between the drain hose and the standpipe is NOT airtight. The standpipe must be at least 18 in or 46 cm high.

You must always exercise caution to avoid collapsing or damaging the drain hose. For best results, the drain hose should not be restricted in any way – by elbows, couplings, or excessive length. For situations where the drain hose cannot be conveniently elevated to at least 18 in or 46 cm, the drain hose must be supported. If drain hose is installed below 18”(46cm), water can be drained in cycle working cause of siphon phenomenon. It causes the washer to “nF” error.

Drain Hose can be installed until 96”(245cm) maximum. But drain capability can be reduced at this height. It causes the washer to have odor, because of remained water in the drain system.

Connection the hose guide within 6”(15cm) from the end of the drain hose. If the drain hose is extended more than 6”(15cm) beyond the end of the hose guide, mold or microorganisms could spread to the inside of the washer.

96” Max 18” Min

Laundry tub

Stand pipe

Hose

retainer

Tie strap

Cold Hot

96” Max 18” Min

2. Check the inlet hose to ensure a washer is inside each ﬁll hose.

Thread the inlet hoses to the HOT and COLD faucet connections. On the other end of the hose, check for one rubber washer per hose and attach each ﬁll hose to the water valve. Make sure the hose with Hot printed on it is attached to the HOT faucet. Tighten by hand until snug, then two-thirds of a turn with pliers.

For correct water use, connect both HOT and COLD water valves. If either or both are not connected, an “nF” (no ﬁll) error can occur.

3. Turn on the “HOT” and “COLD “water supply and check the water valve and the water supply connections for leaks.

Rubber Washer

Cold printed Hot printed

18_ Installing your washer

WF405ATPA-03145A-09_EN.indd 18 2014-2-24 11:33:06

4. Slide your washer into position.

5. Level your washer by turning the leveling legs in or out as

necessary by hand or by using the wrench included with your washer. When your washer is level, tighten the locking nuts using the wrench or (-) ﬂathead screwdriver.

6. Plug the power cord into a 3-Prong, well grounded 120 volt

60Hz approved electrical outlet protected by a 15-amp fuse or comparable circuit breaker. Your washer is grounded through the third prong of the

Locking Nut

power cord when plugged into a three-prong grounded receptacle.

Your washer must be leveled on all four sides. A carpenter’s level should be used on all four corners of your washer. We recommend you recheck your washer after a dozen or so washes to make sure it’s sitll level.

Avoid damage to the legs. Do not move the washer unless the Locking-nuts are fastened to the bottom of the washer.

Test run Make sure that you install your washing machine correctly by running the Rinse+Spin cycle after the installation is complete.

01 Installing your washer

Levelling Leg

STEP 4

Calibration mode

Your Samsung washing machine automatically detects the weight of the laundry. For more accurate weight detection, please run Calibration Mode after the installation. To run Calibration Mode, follow these steps:

1. Turn on the washer.

2. Press the Temp button and Delay Start button simultaneously for at least 3 seconds.

3. Remove any contents in the tub and close the door.

4. Press the Start/Pause button.

5. The drum rotates clockwise and counterclockwise for approximately 3 minutes.

6. When Calibration Mode is ﬁnished, the “En/End” appears on the display and the washing

machine turns o automatically. The washing machine is now ready for use.

Installing your washer _19

WF405ATPA-03145A-09_EN.indd 19 2014-2-24 11:33:08

operating instructions

To reduce the risk of ﬁre, electric shock, or injury to persons, read the IMPORTANT SAFETY INSTRUCTIONS before operating this appliance.

WARNING

LOADING YOUR WASHER

• You can ﬁll the tub with dry, unfolded clothes, but DO NOT OVERLOAD the tub. No more than 3/4 full.

• Overloading may reduce washing eciency, cause excess wear, and possibly cause creasing or

wrinkling of the load.

• Wash delicate items such as bras, hosiery, and other lingerie in the Delicates cycle with similar lightweight items.

• When washing big bulky items or a few smaller items that don’t ﬁll the tub completely – a rug, a pillow, stued toys, or one or two sweaters, for example – add a few towels to improve tumbling and spin performance.

During the spin cycle, the washer may add additional water to redistribute the clothes and correct an inbalance inside the drum.

• To ensure good cleaning result when washing heavily soiled loads, do not overload your washer.

• When the “Garment+

1. Press the Start/Pause Button.

2. Wait for the Door Lock light to go out (5 seconds).

3. Add the item, close the door, and press the Start/Pause Button.

After a 10-second pause, the cycle will resume.

To ensure thorough cleaning, add items within ﬁve minutes of starting the wash cycle.

” light is ON (see page 24), you can add or remove laundry items during a wash.

WASHING CLOTHES: BASIC INSTRUCTIONS

1. Press the Power button, open the door, and then load the washer.

2. Close the door.

Push the laundry into the drum completely to prevent the laundry from being caught in the door or

CAUTION

from falling out of the drum.

3. Add detergent and additives to the dispenser (see pages 28~29).

4. Select the appropriate cycle and options for the load (see pages 21~23 and 26).

5. Press the Start/Pause Button.

The drum automatically rotates and measures the weight of the laundry without supplying water in order to adjust the wash time. (The rotating display on the display panel indicates that the weight of the laundry is being measured.)

6. The Wash Indicator light will illuminate.

7. The estimated cycle time will appear in the display.

The time may ﬂuctuate to indicate the time remaining in the cycle better.

The actual time required for a cycle may dier from the estimated time in the display depending on the water pressure, water temperature, detergent, and laundry.

8. Before your washer starts to ﬁll, it will make a series of clicking noises to check the door lock and do a quick drain.

• When the cycle is complete, the Door Lock light will go out and “End” will appear in the display.

• DO NOT attempt to open the door until the Door Lock light is o. To add a forgotten item, see the

“Loading your Washer” section above.

• When your washer is restarted after a pause, expect a delay of up to 15 seconds before the cycle continues.

• Pressing the Power button cancels the cycle and stops your washer. The Pre Wash, Wash, Rinse, and Spin indicator lights will illuminate during those portions of the

•

cycle.

Do not place anything on top of your washer while it is running.

WARNING

20_ operating instructions

WF405ATPA-03145A-09_EN.indd 20 2014-2-24 11:33:08

washing a load of laundry

OVERVIEW OF THE CONTROL PANEL

03 washing a load of laundry

Cycle Selector

1 654

Select the appropriate cycle for the type of load. This will determine the tumble pattern and spin speed for the cycle.

To minimize wrinkling of laundry, select the Perm Press cycle.

Eco Cold - Provides useful, gentle, and energy saving daily care for normally and lightly soiled laundry using only cold water.

This cylce cleans as eectively as the warm wash setting on the Conventional Normal* cycle under Normal and Light Soil level options. (Cleaning performance of Eco Cold cycle may not be equal to conventional Normal cycle under the heavy soil level option) For best result, we recommend using for loads of 8 pounds or less.

* Conventional Normal cycle - Normal cycle on previous and existing Samsung front loading washers released until 2009 without PowerFoam.

Normal - For most fabrics including cottons, linens, and normally soiled garments.

Heavy Duty - For sturdy, colorfast fabrics and heavily soiled garments. Bedding PLUS - For bulky items such as blankets, comforters and sheets.

When you are washing bulky items, use liquid detergent Sanitize - For heavily soiled, colorfast garments. This cycle heats the water to

150 °F to eliminate bacteria.

If you select pause during the heating portion of the Sanitize Cycle, your Washer door will remain locked for your safety.

Stain Away - For stained clothes. The Stain Away cycle provides outstanding stain removal performance, with the utmost gentle care, avoiding the need for pre-treatment of stains. For best stain removal performance, we recommend using the hot temperature option in this cycle, in which the wash temperature is increased using the internal heater, for overall cleaning of a wide variety of stains. Deep Steam - For heavily soiled, colorfast garments, this cycle provides a high washing temperature and steam and is eective for cleaning stains.

7 9

82 3

washing a load of laundry _21

WF405ATPA-03145A-09_EN.indd 21 2014-2-24 11:33:09

washing a load of laundry

Perm Press - For wash-and-wear, synthetic fabrics, and lightly to normally soiled garments.

Active Wear - Use this cycle to wash exercise wear such as sports jerseys, training pants, shirts/tops and other performance clothing. This cycle provides eective soil removal with gentle action for special fabric care. Delicates/Hand Wash - For sheer fabrics, bras, lingerie silk, and other handwash-only fabrics. For best results, use liquid detergent. Wool - For machine-washable wool. Loads should be under 8 pounds. For best results, we recommend a load of 4.4 pounds or less.

• The Wool cycle washes laundry by moving the wash drum horizontally to maintain the characteristics of the wool ﬁbers and to prevent damage to the cloth. It then stops for a while to allow the laundry to soak in the water. This pause in the operation of the Wool cycle is normal.

• We recommend you use a neutral detergent to prevent damage to the cloth and to improve the washing results.

Quick Wash - For lightly soiled garments needed quickly. Rinse + Spin - Use for loads that need rinsing only or to add rinse-added

fabric softener to a load. The large Digital Display is easy to use. It provides instructions and

Digital display

Select Cycle

Option

Temperature

selection button

diagnostics while keeping you updated on the cycle status and time remaining.

Press these buttons to select dierent cycle options.

Pure Cycle

(after every 40 washes) is recommended. No detergent or bleach is needed (see page 33). Steam - Press this button to use the Steam Wash function. Steam Wash is available with the Normal, Heavy Duty, Bedding PLUS, Sanitize, Stain Away and Deep Steam cycles. For heavily soiled, colorfast garments, Steam Wash improves stain treatment and uses less water (See page 27). The steam may not be visible during the Steam cycle, and may also not always be visible while the total steam cycle is being performed. Delay Start - Any cycle can be delayed for up to 24 hours in one-hour increments. Displayed hour indicates the time at which the wash will be started. (See page 25). Pre Wash - To use this feature, add detergent to the pre wash section of the detergent compartment. When turned on, the washer ﬁlls with cold water and detergent, tumbles, then drains and advances to the selected wash cycle. Some cycles cannot be selected with this option (See page 28~29).

Extra Rinse - Add an additional rinse at the end of the cycle to remove laundry additives and perfumes more thoroughly.

Extra Spin - Add additional time to remove more water from loads. My Cycle - Choose your favorite cycle including temperature, spin, soil level,

options, etc. (see page 25) Press the button repeatedly to cycle through the dierent water temperature options.

Extra Hot - Heavily soiled, colorfast items. Hot - Whites and heavily soiled, colorfast items. Warm - Colorfast items. When you select warm rinse, only the ﬁnal rinse will

be warm. The other rinses will be cold to conserve energy.

Eco Warm - Moderately soiled, colorfast items, most wrinkle-free items. Cold - Brightly colored, very lightly soiled items.

- Use to clean dirt and bacteria from the drum. Regular use

You cannot select the prewash option in the Wool, Quick Wash, Delicates/Handwash and Rinse+Spin cycles.

22_ washing a load of laundry

WF405ATPA-03145A-09_EN.indd 22 2014-2-24 11:33:09

Spin selection

button

Soil selection

button

Signal selection

button Start/Pause

selection button

Power button

Child Lock

Child Lock prevents children from playing with your washer. Once you have activated the Child Lock function, the control panel cannot be activated,

preventing children from playing with the washer.

Press the button repeatedly to cycle through the dierent spin speed options. Extra High - Removes more water from loads during spin.

To minimize wrinkling of wrinkle-free and no-iron fabrics, DO NOT use the Extra High spin option for these loads, nor overload your washer.

High - Use for underwear, t-shirts, jeans, and sturdy cottons. Medium - Use for jeans, wrinkle-free, or wash-and-wear items and

synthetics.

Low - Use for delicate items needing a slow spin speed. No Spin - Drains your washer without spinning. Use for extremely delicate

items that cannot tolerate any spin. Press the button to select the soil level/washing time. (Light 

 Normal

  Heavy)

Heavy - For heavily soiled loads.

Normal - For moderately soiled loads. This setting is best for most loads.

Light - For lightly soiled loads.

Press the button to select the signal level. (O 

 Softer   Louder)

Press to pause and restart programs.

Press once to turn your washer on, press again to turn your washer o. If the washer is left on for more than 10 minutes without any buttons being touched, the power automatically turns o.

03 washing a load of laundry

Activating the Child Lock function

Press and hold both the Soil Level and Signal buttons simultaneously for approximately 3seconds.

• When you activate the Child Lock function, the door locks and the “Child Lock

” lamp

illuminates.

• If you press the Start/Pause button after you have activated the Child Lock function , none of the buttons will work except for the Power button.

• If you press a button when the buttons are locked, the “Child Lock

” lamp blinks.

Pausing the Child Lock function

When the door is locked or the buttons are locked by the Child Lock function, you can pause the Child Lock operation for 1 minute by pressing and holding both the Soil Level and Signal buttons simultaneously for approximately 3 seconds.

• If you pause the Child Lock mode temporarily, the door lock is released for 1 minute for user convenience. During this period, the “Child Lock

• If you open the door after the minute is over, an alarm sounds for up to 2 minutes.

• If you close the door within the 2 minutes, the door is locked and the Child Lock function is

reactivated. If you close the door after the 2 minutes, the door is not locked automatically and no alarm sounds.

” lamp blinks.

washing a load of laundry _23

WF405ATPA-03145A-09_EN.indd 23 2014-2-24 11:33:11

washing a load of laundry

Deactivating the Child Lock function

Press and hold both the Soil Level and Signal buttons simultaneously for approximately 6seconds.

• When you deactivate the Child Lock function, the door is unlocked and the “Child Lock

• TheChildLockfunctionpreventschildrenortheinrmfromaccidentlyoperatingthewasherand

WARNING

CAUTION

Spin Only

If you press the Power button and then press and hold the Spin button for 2 seconds, the spin time will be displayed on the display panel.

Then, press the Spin button repeatedly until the required spin level is selected, and then press the Start/Pause button.

injuring themselves.

• Ifachildentersthewashingmachine,thechildmaybecometrappedandsuocate.

• OnceyouhaveactivatedtheChildLockfunction,itcontinuesworkingevenifthepoweristurned

o.

• Openingthedoorbyforcecanresultininjuryduetodamagetotheproduct.

To add laundry after you have activated the Child Lock function, you must ﬁrst pause or deactivate the Child Lock function.

If you want to open the door of the washing machine when the Child Lock function is activated:

• PauseordeactivatetheChildLockfunction.

• Turnthewashingmachineoandthenonagain.

Before pressing the Spin Only button to use the Spin Only function, you can select a cycle with the Cycle Selector. If you have selected a cycle, you can only select the spin level corresponding to the selected cycle.

” is turned o.

Garment+

You can add or take out laundry items even after the wash has started, as long as the “Garment+ ” light is on. Pushing the Start/Pause button unlocks the door, unless the water is too hot or if there is too much water in your washer. If you are able to unlock the door and wish to continue the wash cycle, close the door, and then press the Start/Pause button.

Delay Start

You can set the washing machine to start your wash automatically at a later time, choosing a delay time. The hour displayed indicates the time at which the wash will be started.

1. Set your wash course.

2. Press the Delay Start button repeatedly until the delay time is set.

3. Press the Start/Pause button. The “Delay Start

counting down until it reaches the set time.

4. To cancel a Delay Start function, press the Power button and then turn the washing machine on again.

” indicator will be lit, and the clock will begin

24_ washing a load of laundry

WF405ATPA-03145A-09_EN.indd 24 2014-2-24 11:33:13

My Cycle

Allows you to activate your custom wash (temperature, spin, soil level, etc.) with one–button convenience. By pushing the My Cycle button, you activate the settings used during the My Cycle mode. The “My Cycle” light goes on, indicating activation. You can select all options as follows in “My Cycle” mode.

1. Press the My Cycle button on the Control Panel.

2. Select the cycle using the Cycle Selector dial.

3. After cycle selection, set each option.

See page 39 for available option settings with each cycle.

4. Start “My Cycle” by pushing the Start/Pause button in “My Cycle” mode. The washer will display the cycle and options you selected the next time you choose “My Cycle”.

You can change the “My Cycle” settings by repeating the process above. The washer displays the last settings used the next time you choose “My Cycle”.

To program “My Cycle” settings into your washer, the washer needs to complete an entire wash cycle. If for any reason the wash cycle is interrupted and the washer does not ﬁnish the cycle, it will not program in the settings for later use.

Smart Care

This function enables you to check the status of the washing machine using a smartphone.

1. Press and hold the Smart Care button for 3 seconds to use the Smart Care function when an error occurs or if you do not press any buttons since you turn on the washer.

• Theerrorcodehistoryisdeletedafterusingthefunction.

2. If the Smart Care function is activated, the LED on the window display rotates for 2 or 3 seconds and then the Smart Care indicator is lit on the display.

3. Run the Smart Care app on your smart phone.

• TheSmartCarefunctionisoptimizedwithGalaxyS,GalaxyS2,iPhone4andiPhone4S.

4. Focus your smart phone’s camera on the display panel of the washing machine.

5. If the smart phone’s camera is focused on the display panel of the washing machine,

the panel and error message is automatically recognized and the error type and countermeasures are displayed on the smart phone.

6. If the smartphone fails to recognize the error code more than twice, please enter the error code displayed on the display panel of the washer manually into the Smart Care app.

Downloading the Smart Care app

• DownloadtheSamsungLaundryAppintoyourmobilephone

from the Android market or Apple App store. (Search word : Samsung Smart Washer/Dryer)

Precautions when using Smart Care

• Iflightfromalightbulb,uorescentbulb,orlampisreectedon

the display panel of the washing machine, the smartphone may not be able to recognize the panel or error mesage easily.

• Ifyouholdthesmartphoneattoolargeananglerelativetothe

front of the display panel, it may not be able to recognize the error code. For best results, hold the smartphone so that the front of the panel and the smartphone are parallel or nearly parallel.

03 washing a load of laundry

washing a load of laundry _25

WF405ATPA-03145A-09_EN.indd 25 2014-2-24 11:33:15

washing a load of laundry

DEEP STEAM

DEEP STEAM (Magic Steam) The Deep Steam feature boosts cleaning performance and loosens grime and dirt, providing superior

cleaning results. For heavily soiled, colorfast garments, this cycle provides a high washing temperature and steam and is

eective for cleaning stains.

How DEEP STEAM works If you select steam, the steam acts at the most eective times for the detected amount of laundry,

maximizing the eect of the steam, increasing the wash temperature, enhancing the Soak eect, and improving wash performance.

Press Steam button to use the Steam Wash function. Steam Wash is available with the Normal, Heavy Duty, Bedding PLUS, Sanitize, Stain Away and Deep Steam cycles. For heavily soiled, colorfast garments, Steam Wash improves stain treatment and uses less water.

Washer takes small amounts of water in tub and Heater heats water into evaporation.

To use the Steam function, perform the following steps:

1. Load the washer.

2. Press the Power button.

3. Turn the Cycle Selector and select a Steam Cycle. (The Deep Steam course automatically selects Steam.)

4. Press the Steam button.

5. Add detergent to the dispenser tray and add fabric softener up to the marked line.

6. Press the Start/Pause button. The washer automatically selects the optimal wash conditions by sensing the weight of the laundry.

The steam may not be visible during the Steam cycle, and may also not always be visible while the total steam cycle is being performed. This is normal.

•

Too much steam could damage clothing. Do not use steam with delicate fabrics such as wool, silk

CAUTION

or easily discolored fabrics.

•

Steam may not be present during entire steam wash cycle.

•

Do not touch the door. The door surface can become very hot.

Washing clothes using the cycle selector

Your new washing machine makes washing clothes easy, using Samsung’s “Fuzzy Control” automatic control system. When you select a wash program, the machine will set the correct temperature, washing time, and washing speed.

1. Turn on your sink’s water tap.

2. Press the Power button.

3. Open the door.

4. Load the articles of clothing one at a time loosely into the drum, without overﬁlling it.

5. Close the door.

6. Add detergent, softener, and pre-wash detergent (if necessary) into the appropriate

compartments.

Pre-wash is only available when selecting the Eco Cold, Normal, Heavy Duty, Perm Press, Sanitize, Stain Away, Deep Steam, Active Wear and Bedding PLUS cycles. It is only necessary if your clothing is heavily soiled.

26_ washing a load of laundry

WF405ATPA-03145A-09_EN.indd 26 2014-2-24 11:33:16

7. Use the Cycle Selector to select the appropriate cycle according to the type of material:

Normal, Heavy Duty, Perm Press, Sanitize, Bedding PLUS, Deep Steam, Stain Away, Active Wear, Delicates/Hand Wash, Wool, Quick Wash, Rinse+Spin, Eco Cold. The relevant indicators will illuminate on the control panel.

8. At this time, you can control the wash temperature, the number of rinse cycles, the spinning

speed, and the delay time by pressing the appropriate option button.

9. Press the Start/Pause button on the Cycle Selector and the wash will begin. The process

indicator will light up and the remaining time for the cycle will appear in the display.

Pause Option

1. When the “Garment+ ” light is ON, you can add or remove laundry items.

2. Press the Start/Pause button to unlock the door.

You cannot open the door when the water is too HOT or the water level is too HIGH.

3. After closing the door, press the Start/Pause button to restart the wash.

USING STEAM WASH

If you select steam, the steam acts at the most eective times for the detected amount of laundry, maximizing the eect of the steam, increasing the wash temperature, enhancing the Soak eect, and improving wash performance.

1. Load the washer.

2. Press the Power button.

3. Turn the Cycle Selector and select a Steam Cycle. (The Deep Steam course automatically selects

Steam.)

4. Press the Steam button.

5. Add detergent to the dispenser tray and add fabric softener up to the marked line.

6. Press the Start/Pause button.

: The washer automatically selects the optimal wash conditions by sensing the weight of the laundry.

03 washing a load of laundry

Steam may not necessarily be visible during the steam cycles. Steam may not be present during the entire steam wash cycle.

ATC (AUTO TEMPERATURE CONTROL)

ATC is the control function that the washer controls water temperature with temperature sensor (thermistor).

Because there are numerous water temperatures depending on the customer’s environments(cold areas, warm areas, various water temperature, settings of heater temperature, etcs), ATC function in our washer maintains the certain level of wash temperature to output the best washing performance at each cycle.

If you select normal & heavy duty course, those courses are the regulation and UL course. Since new washer must reduce the amount of energy usage at ﬁrst priority, customer will notice more cold water entering the washer. But This is Normal, not a problem.

In those regulation course, Hot temperature is similar to acceptable adult bath-water temperature and warm temperature is similar to comfortable swimming-pool water temperature. If customer want to wash clothes in speciﬁc water temperature, customer should choose a dierent course at each temperature(Hot/Warm/Eco Warm)

washing a load of laundry _27

WF405ATPA-03145A-09_EN.indd 27 2014-2-24 11:33:16

washing a load of laundry

DETERGENT USE

Your Washer is designed to use high eciency (HE) detergents.

• For best cleaning results, use a high eciency detergents such as Tide HE, Wisk HE, Cheer HE, or Gain HE*. High eciency detergents contain suds suppressors that reduce or eliminate suds. When fewer suds are produced, the load tumbles more eciently and cleaning is maximized.

Regular detergent is NOT recommended. Please use HE detergents only.

WARNING

Reducing the amount of detergent may reduce the quality of cleaning. It is important to pre–treat stains, sort carefully by color and soil level, and avoid overloading. * Brand names are trademarks of their respective manufacturers.

FEATURES

Automatic dispenser

Your washer has separate compartments for dispensing detergent and color-safe bleach, chlorine bleach, and fabric softener. Add all laundry additives to their respective compartments before starting your washer.

The automatic dispenser MUST ALWAYS be in place before you start your washer.

DO NOT open the automatic dispenser when your washer is running.

Usage Pointers:

• Never exceed the manufacturer’s recommendations when adding detergent.

• This compartment holds liquid detergent for the main wash cycle, which the washer adds to the load at the beginning of the cycle.

Before using powdered detergent, remove the Liquid Detergent holder from the compartment. Powdered detergent will not dispense from the Liquid Detergent holder.

Liquid Detergent

Pre wash compartment

Detergent compartment

• Pour the recommended amount of laundry detergent directly into the detergent compartment before starting your washer.

28_ washing a load of laundry

WF405ATPA-03145A-09_EN.indd 28 2014-2-24 11:33:17

Pre wash compartment

When using the Pre Wash option, add detergent to both the Pre Wash compartment and the detergent compartment. The washer will automatically dispense the detergent during Pre Wash.

• If you use a high eciency (HE) detergent, add 1/3 of the recommended amount to the Pre Wash compartment and 2/3 of the recommended amount to the detergent compartment.

03 washing a load of laundry

Bleach compartment

(Liquid chlorine bleach only)

1. Add chlorine bleach to the bleach compartment. DO NOT exceed the MAX FILL line.

2. Avoid splashing or over–ﬁlling the compartment.

3. Your washer automatically dispenses bleach into the tub at

the appropriate time.

4. The dispenser automatically dilutes liquid chlorine bleach before it reaches the wash load.

• Never pour undiluted liquid chlorine bleach directly onto the load or into the tub. It is a powerful chemical and can cause fabric damage, such as weakening of the ﬁbers or color loss, if not used properly.

• Oxi-type boosters or color-safe bleach can be added to the drum prior to adding laundry.

• Put the laundry into the drum only after conﬁrming that the oxi-type boosters or color-safe bleach has completely entered the hole of the drum.

• Tousepowdereddetergentandpowderoxi-type

boosters or powdered color-safe bleach at the same time, it is more eective to put them in the drum together before adding the laundry. When you use powdered detergent, remember to remove the Liquid Detergent holder from the detergent compartment.

Fabric Softener

compartment

Bleach

compartment

Fabric softener compartment

1. Pour the recommended amount of liquid fabric softener into the softener compartment.

For smaller loads, use less than one capful.

2. Dilute the fabric softener with water until it reaches MAX FILL in the compartment.

3. The dispenser automatically releases liquid fabric softener at the proper time during the rinse

cycle.

• Use the softener compartment ONLY for liquid fabric softeners.

• DO NOT use a Downy Ball* in the Fabric softener compartment of this washer. It will not

be added at the appropriate time. Use the detergent compartment.

* Brand names are trademarks of their respective manufacturers. If you overﬁll the detergent, bleach, or softener compartments, the contents of the

compartment will automatically be released into the washer. This could damage any garments that are in the drum.

washing a load of laundry _29

WF405ATPA-03145A-09_EN.indd 29 2014-2-24 11:33:18

maintaining your washer

CLEANING THE EXTERIOR

Turn o the water faucets after ﬁnishing the day’s washing. This will shut o the water supply to your washer and prevent the unlikely possibility of damage from

escaping water. Leave the door open to allow the inside of your washer to dry out. Use a soft cloth to wipe up all detergent, bleach or other spills as they occur. Clean the following as recommended below: Control Panel – Clean with a soft, damp cloth. Do not use abrasive powders or cleaning pads. Do not spray

cleaners directly on the panel. Cabinet – Clean with soap and water.

CLEANING THE INTERIOR

Clean the interior of your washer periodically to remove any dirt, soil, odor, mold, mildew, or bacterial residue that may remain in your washer as a result of washing clothes.

Failure to follow these instructions may result in unpleasant conditions, including odors and/or permanent stains on your washer or laundry.

Hard water deposits may be removed, if needed. Use a cleaner labeled “Washer safe”.

CLEANING THE DISPENSERS

You may need to clean the automatic dispenser periodically to remove laundry additive buildup.

1. Pull out the Liquid Detergent holder from the detergent compartment.

2. Remove the siphon cap from the fabric softener and bleach

compartments.

3. Wash all of the parts under running water.

4. Clean the dispenser recess with a soft brush.

5. Reinsert the siphon cap and push it ﬁrmly into place.

6. Push the Liquid Detergent holder back into place.

7. Run a Rinse+Spin cycle without any load in your washer.

Siphon cap

STORING YOUR WASHER

Washers can be damaged if water is not removed from hoses and internal components before storage. Prepare your washer for storage as follows:

• Select the Quick Wash cycle and add bleach to the automatic dispenser. Run your washer through the cycle without a load.

• Turn the water faucets o and disconnect the inlet hoses.

• Unplug your washer from the electrical outlet and leave your washer door open to let air circulate inside

the tumbler.

• If you store your washer in below–freezing temperatures, make sure you allow time for any leftover water in your washer to thaw before use.

30_ maintaining your washer

WF405ATPA-03145A-09_EN.indd 30 2014-2-24 11:33:19

+ 114 hidden pages