Page 1
User Manual (WCT730M)
1. Introduction
WCT730M is a Wi-Fi / Bluetooth Combo module compliant with IEEE802.11 a.b.g.n.ac MAC/baseband/radio and
Bluetooth 5.0 optimized for low-power applications.
WCT730M is the 802.11a/b/g/n /ac +Bluetooth 5.0 Combo Module that acts as a communication controller for users
of a wireless device to connect to SMART TV.
- Features
>IEEE 802.11ac Draft compliant.
>Dual-band 2.4GHz /5 GHz
>Dual-stream spatial multiplexing up to 600Mbps data rate
>Support 20, 40, 80MHz channel
>On-chip power amplifiers and low –noise amplifiers for both bands
>Complies with Bluetooth Core Specification Version 5.0
>Supports BT/Wi-Fi coexistence.
>Adaptive frequency hopping (AFH) for reducing radio frequency interference
- Wi-Fi Transmission
Baseband data is modulated and up converted to the 2.4GHz ISM and 5-GHz U-NII bands, respectively.
IC has DSSS (BPSK/QPSK/CCK) and OFDM (BPSK/QPSK/16QAM/64QAM/25QAM) modulation function, it
provides transmission data rate are 1, 2, 5.5, 11Mbps on DSSS and 6, 12, 18, 24, 36, 48, 54 Mbps on OFDM.
- Wi-Fi Receiver
The WCT730M has a wide dynamic range, direct conversion receiver that employs high-order on-chip channel
filtering to ensure reliable operation in the noisy 2.4GHz ISM band or the entire 5GHz U-NII band .
-Bluetooth Low Energy
The WCT730M support the Bluetooth 4.2 LE and 5.0 BLE 2Mbps
- Adaptive Frequency Hopping
The WCT730M link quality statistics on a channel by basis to facilitate channel assessment and
Channel map selection. The link quality is determined using both RF and baseband signal processing to Provide a
more accurate frequency-hop map.
Version 1.0 page 1 of 5
Page 2
4. Product Details
-Frequency Range
2400-2497MHz
5150-5350MHz
5470-5725MHz
5725-5825MHz
5850-5925MHz
- IEEE 802.11n HT20
- IEEE 802.11n HT40
Version 1.0 page 2 of 5
Page 3
-IEEE 802.11ac
-Recommended Operating conditions
Operating voltage 4.5
Operating temperature(ambient) -20 25 50 °C
-AS Information
Company Name:
Tel:
Min Typ. Max Unit
5
5.5 V
Version 1.0 page 3 of 5
Page 4
Approval Statement
CE approval
-This device is restricted to indoor use only within the 5.15 ~ 5.35GHz Band. (Europe)
Frequency Range and Maximum Output Power (EIRP)
2400 MHz to 2483.5 MHz : Below 20 dBm for Bluetooth
2400 MHz to 2483.5 MHz : Below 20 dBm for 802.11b/g/n
5150MHz to 5250 MHz : Below 23 dBm for 802.11a,n,ac
5350MHz to 5725 MHz : Below 20 dBm for 802.11a,n,ac
5725MHz to 5875 MHz : Below 14 dBm for 802.11a,n,ac
FCC approval
This device complies with Part 15 of the FCC`s Rules. Operation is subject to the following two Conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesirable operation.
To satisfy FCC exterior labeling requirements, the following text must be placed on the exterior of the end product.
Contains Transmitter module FCC ID: A3LWCT730M
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/ TV technician for help.
-The OEM integrator is responsible for ensuring the end-user has no manual instruction to remove or install module.
-The module is limited to installation in mobile or fixed applications.
IC approval
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic
Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause undesired operation of the
device.
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation,
Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation
est autorisée aux deux conditions suivantes :
(1) L’appareil ne doit pas produire de brouillage;
(2) L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en
compromettre le fonctionnement.
Version 1.0 page 4 of 5
Page 5
The host device must be labeled to display the Industry Canada certification number of the module.
Contains transmitter module IC:649E-WCT730M
Le dispositif d'accueil doivent être étiquetés pour afficher le numéro de certification d'Industrie Canada du module.
Contient module émetteur IC :649E-WCT730M
IMPORTANT NOTE
This device complies with FCC & IC radiation exposure limits set forth for an uncontrolled environment. This device
should be installed and must not be co-located or operating in conjunction with any other antenna or transmitter.
This device is intended only for OEM integrators under the following conditions:
1) This module may not be co-located with any other transmitters or antennas.
2) The antenna must be installed such that 20cm is maintained between the antenna and users.
As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is
still responsible for testing their end-product for any additional compliance requirements with this module installed.
In the event that these conditions cannot be met, then the FCC & IC authorizations are no longer considered valid
and the FCC ID cannot be used on the final product. In these circumstances, the OEM integrator will be responsible
for re-evaluating the end product including this module and obtaining separate FCC & IC authorizations.
Cet appareil est conforme aux limites de la FCC et IC exposition aux radiations dans un environnement non contrôlé.
Cet appareil doit être installé et ne doit pas être co-localisées ou opérant en conjonction avec une autre antenne ou
un autre émetteur.
Cet appareil est conçu uniquement pour les intégrateurs OEM dans les conditions suivantes :
1 ) L' antenne doit être installée de telle sorte que 20 cm est maintenue entre l'antenne et les utilisateurs .
2 ) Ce module ne peut pas être co-localisé avec d'autres émetteurs ou des antennes .
Aussi longtemps que deux conditions précitées sont remplies, le test du transmetteur supplémentaires ne seront
pas tenus. Toutefois, l'intégrateur OEM est toujours responsable de tester leurs produits finis pour toutes les
exigences de conformité supplémentaires avec ce module installé.
Dans le cas où ces conditions ne peuvent pas être remplies, alors la FCC et IC autorisations ne sont plus considérés
comme valides et l'ID de la FCC ne peut pas être utilisé sur le produit final. Dans ces circonstances, l'intégrateur
OEM sera responsable de réévaluer le produit final, y compris l'obtention de ce module et séparée de la FCC et IC
Autorisations
User Information
Caution: Any changed or modifications not expressly approved by the party responsible for compliance could
void the user`s authority to operate this equipment.
Attention: Toute changé ou modifications non expressément approuvés par la partie responsable de la conformité
pourraient annuler l'utilisateur `autorité de faire fonctionner cet équipement.
-This device is restricted to indoor use only within the 5.15 ~ 5.25GHz Band. (Canada)
-User should also be advised that high-power radars are allocated as primary users (i.e. priority users) of the bands
5250-5350 MHz and 5650-5850 MHz and that these radars could cause interference and/or damage to LE-LAN
devices.
-Cet appareil est restreint à l'utilisation à l'intérieur seulement dans la bande 5.15 ~ 5.25GHz.
Version 1.0 page 5 of 5
Loading...