Samsung WCM730Q User Manual

Version 1.0

Samsung Electronics

page 1 of 5

Approval statement

FCC Statement

To satisfy FCC exterior labeling requirements, the following text must be placed on the exterior of the end product.
Contains Transmitter module FCC ID: A3LWCM730Q
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/ TV technician for help.
This device complies with Part 15 of the FCC`s Rules. Operation is subject to the following two Conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including interference that may cause undesirable operation.

IC Information

This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two
conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired operation of the device.

Cet appareil est conforme avec Industrie Canada exempts de licence standard RSS (s). L'opération est soumise aux deux
conditions suivantes:
(1) cet appareil ne peut causer d'interférences, et
(2) cet appareil doit accepter toute interférence, y compris les interférences qui peuvent causer un mauvais fonctionnement
de l'appareil.

The end product must be labeled to display the Industry Canada certification number of the module.
Contains transmitter module IC: 649E-WCM730Q

Le dispositif d'accueil doivent être étiquetés pour afficher le numéro de certification d'Industrie Canada du module.
Contient module émetteur IC : 649E-WCM730Q

User Information

This device complies with FCC & IC radiation exposure limits set forth for an uncontrolled environment. This device should
be installed and must not be co-located or operating in conjunction with any other antenna or transmitter.

Version 1.0

Samsung Electronics

page 2 of 5

This device is intended only for OEM integrators under the following conditions:

1) The antenna must be installed such that 20cm is maintained between the antenna and users.

2) This module may not be co-located with any other transmitters or antennas.
As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still
responsible for testing their end-product for any additional compliance requirements with this module installed. In the event
that these conditions cannot be met, then the FCC & IC authorizations are no longer considered valid and the FCC ID
cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end
product including this module and obtaining separate FCC & IC authorizations.

Cet appareil est conforme aux limites d'exposition rayonnement de la FCC et IC définies pour un environnement non
contrôlé . Cet appareil doit être installé et ne doit pas être co- localisées ou opérant en conjonction avec une autre antenne
ou émetteur .
Cet appareil est conçu uniquement pour les intégrateurs OEM dans les conditions suivantes :
1 ) L' antenne doit être installée de telle sorte que 20 cm est maintenue entre l'antenne et les utilisateurs .
2 ) Ce module ne peut pas être co-localisé avec d'autres émetteurs ou des antennes .
Tant que deux conditions ci-dessus sont remplies , nouvel essai de l'émetteur ne sera pas tenu . Cependant , l'intégrateur
OEM est toujours responsable de tester leur produit final pour les exigences de conformité supplémentaires avec ce module
installé .Dans le cas où ces conditions ne peuvent être remplies, les autorisations de la FCC et IC ne sont plus considérés
comme valides et l'ID FCC ne peuvent pas être utilisés sur le produit final . Dans ces circonstances , l'intégrateur OEM sera
chargé de réévaluer le produit final incluant ce module et l'obtention des autorisations de la FCC et IC distincts .

Any changed or modifications not expressly approved by the party responsible for compliance could void the user`s
authority to operate this equipment.

Toute changé ou modifications non expressément approuvés par la partie responsable de la conformité pourraient annuler
l'utilisateur `autorité de faire fonctionner cet équipement.

This device is restricted to indoor use only within the 5.15 ~ 5.25GHz Band.

Channels 120-128 are used only if permitted by a master device.
The device’s processor constantly monitors each data session and automatically discontinues transmission in the absence
of information to transmit within 4 ms or when operational failure is detected by the CPU watchdog timers.
The device shall automatically discontinue transmission in case of either absence of information to transmit or operational
failure. These provisions are not intended to preclude the transmission of control or signalling information or the use of
repetitive codes used by certain digital technologies to complete frame or burst intervals. Applicants shall include in their
application for equipment authorization a description of how this requirement is met.

FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment
should be installed and operated with minimum distance 20cm between the radiator & your body.

IC Radiation Exposure Statement:

This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with minimum distance 20cm between the radiator & your body.