Samsung WBW880A Users Manual

Installation Procedure

① Tighten the screw.

② Assembly the main antenna.

③ Assembly the aux antenna.

④ Insert the cable.

③

①

②

④

FCC Statement

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy and, if not installed and

used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one of the following measures:

● Reorient or relocate the receiving antenna.

● Increase the separation between the equipment and receiver.

● Connect the equipment into an outlet on a circuit different from that to which the receiver

is connected.

● Consult the dealer or an experienced radio/TV technician for help.

page 1 / 9

Version 1.0

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) This device may not cause harmful interference, and (2) this device must

accept any interference received, including interference that may cause undesired operation.

FCC Caution: Any changes or modifications not expressly approved by the party responsible

for compliance could void the user’s authority to operate this equipment.

This device and its antenna(s) must not be co-located or operation in conjunction with any

other antenna or transmitter.

IMPORTANT NOTE:

FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled

environment.

This equipment should be installed and operated with minimum distance 20cm between the

radiator & your body.

This module is intended for OEM integrator. The OEM integrator is still responsible for the

FCC compliance requirement of the end product, which integrates this module.

USERS MANUAL OF THE END PRODUCT:

In the users manual of the end product, the end user has to be informed to keep at least

20cm separation with the antenna while this end product is installed and operated. The end

user has to be informed that the FCC radio-frequency exposure guidelines for an

uncontrolled environment can be satisfied. The devices must be installed and used in strict

accordance with the manufacturer's instructions as described in the user documentation that

comes with the product.The end user has to also be informed that any changes or

modifications not expressly approved by the manufacturer could void the user's authority to

operate this equipment. If the device is small or for such use that it is not practicable to place

the statement on the product, then additional FCC part 15.19 statement is required to be

available in the users manual: This device complies with Part 15 of FCC rules. Operation is

subject to the following two conditions: (1) this device may not cause harmful interference

page 2 / 9

Version 1.0

and (2) this device must accept any interference received, including interference that may

cause undesired operation.

LABEL OF THE END PRODUCT:

The final end product must be labeled in a visible area with the following " Contains FCC ID:

A3LWBW880A". If the device is small or for such use that it is not practicable to place the

statement on the product, then the following FCC part 15.19 statement has to also be

available on the label: This device complies with Part 15 of FCC rules. Operation is subject

to the following two conditions: (1) this device may not cause harmful interference and (2)

this device must accept any interference received, including interference that may cause

undesired operation.

IC Statement

This Class B digital apparatus complies with Canadian ICES-003.

This device complies with Industry Canada license-exempt RSS standard(s).

Operation is subject to the following two conditions: (1) this device may not cause

interference, and (2) this device must accept any interference, including interference that

may cause undesired operation of the device.

Cet appareil numérique de la classe B est conforme á la norme NMB-003 du Canada.

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils

radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1)

l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout

brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le

fonctionnement.

Any changes or modifications not expressly approved by the manufacturer could void the

user's authority to operate this equipment.

This device and its antenna(s) must not be co-located or operation in conjunction with any

other antenna or transmitter.

This radio transmitter (identify the device by certification number or model number if

Category II) has been approved by Industry Canada to operate with the antenna types listed

page 3 / 9

Version 1.0