User manual
WA4837700A*/WA4837770A*
_"]"_J SEC
....................................................n
Contents
Safety information
What you need to know about the safety instructions
Important safety symbols
Important safety precautions
Installation
Unpacking your washer
Overview of your washer
Basic location requirements
Important note to installer
Step-bpstep installation
Operating instructions
Loading your washer
Getting started
Washing a load of laundry
Control panel
Cycle overview
Options
Washing clothes using the cycle selector
ATC (Auto Temperature Control)
The basics
Detergent use
Features
4
4
4
5
13
!3
!4
!6
20
20
28
28
29
3O
30
32
33
36
38
39
4!
42
Maintaining your washer
Cleaning the exterior
Cleaning the interior
Storing your washer
Preserving the top cover and the front frame
Cleaning the dispensers
Self Clean
Troubleshooting
Checkpoints
Information codes
2 English
WA7700] WA48J7700AW 03520D 01 ENindd 2 2015/4/16 9:38:29
46
46
46
46
47
47
49
5O
SO
54
Specifications 57
Fabric care chart
Helping the environment
Declaration of conformity
Specification sheet
Cycle chart
57
59
59
6O
6!
English 3
WA7700] WA48J7700AW 03520D 01 ENindd 3 2015/4/16 9:38:29
Safety information
Congratulations on your new Samsung washer. This manual contains important information
on the installation, use and care of your appliance. Please take some time to read this manual
to take full advantage of your washer's many benefits and features.
What you need to know about the safety instructions
Please read this manual thoroughly to ensure that you Know how to safely and efficiently
operate the extensive features and functions of your new appliance. Please store the manual
in a safe location close to the appliance for future reference. Use this appliance only for its
intended purpose as described in this instruction manual.
Warnings and Important Safety Instructions in this manual do not cover all possible
conditions and situations that may occur. It is your responsibility to use common sense,
caution and care when installing, maintaining and operating your washer.
Because the following operating instructions cover various models, the characteristics of your
washer may differ slightly from those described in this manual and not all warning signs
may be applicable. If you have any questions or concerns, contact your nearest service center
or find help and information online at www.samsung.com.
Important safety symbols
What the icons and signs in this user manual mean:
/_ WARNING
Hazards or unsafe practices that may result
damage.
/_ CAUTION
Hazards or unsafe practices that may result
NOTE
Indicates that a risk of personal injury or material damage exists.
n severe personal injury, death and/or property
n personal injury and/or property damage.
SAVE THESE INSTRUCTIONS
4 English
\VA771)0] WA481771)0A_' 03520D 01 ENindd 4 2(115/4/16 9:38:29
These warning signs are here to prevent injury to yourself and others.
Please follow them explicitly.
After reading this manual, store it in a safe place for future reference.
Read all instructions before using the appliance.
As with any equipment that uses electricity and moving parts, potential hazards exist. To
safely operate this appliance, familiarize yourself with its operation and exercise care when
using it.
Important safety precautions
/!'x, WARNING
To reduce the risk of fire, electric shock, or injury to persons when using your appliance,
follow basic precautions, including the following:
1. Read all instructions before using this appliance.
2. Do not wash or dry articles that have been previously cleaned in, washed in, soaked in, or
spotted with gasoline, dry-cleaning solvents, other flammable or explosive substances as
they give off vapors that could ignite or explode.
3, Do not allow children to play on or in the appliance. Close supervision of children is
necessary when the appliance is used near children.
4, Before the appliance is removed from service or discarded, remove the lid of the washing
or drying compartment.
5, Do not reach into the appliance if the drum is moving.
6, Do not install or store this appliance where it will be exposed to the weather.
7, Do not tamper with the controls.
8, Do not repair or replace any part of the appliance or attempt any servicing unless it is
specifically recommended in the user-maintenance instructions or in published user-
repair instructions that you understand and have the skills to carry out.
9, Do not add gasoline, dry-cleaning solvents, or other flammable or explosive substances to
the wash water. These substances give off vapors that could ignite or explode.
SAVE THESE iNSTRUCTiONS
English
\\rA771)()] \\rA481771)(/A_ _ ()3520D 01 ENindd 5 2(115/4/16 9:38:29
Safety information
10, Under certain conditions, hydrogen gas may be produced in a hot water system that
has not been used for 2 weeks or more. HYDROGEN GAS IS EXPLOSIVE. If the hot water
system has not been used for 2 weeks or more, before using a washer or combination
washer-dryer, turn on all hot water faucets and let the water flow from each for several
minutes. This will release any accumulated hydrogen gas. As the gas is flammable, do not
smoke or use an open flame during this time.
,/iX WARNING - State of California Proposition 65 Warnings:
This product contains chemicals known to the State of California to cause cancer and
reproductive toxicity.
Critical installation warnings
/_ WARNING
Plug the power cord into an AC !20 V/60 Hz/wall socket rated at 15 amps or higher. Use
the socket for this appliance only. In addition, do not use an extension cord.
• Sharing a wall socket with other appliances, using a power strip, or extending the power
cord may result in electric shock or fire.
• Do not use an electric transformer. It may result in electric shock or fire.
• Ensure that the power voltage, frequency, and current match the product's specifications.
Failing to do so may result in electric shock or fire.
Have this appliance installed by a qualified technician or service company.
• Failing to do so may result in electric shock, fire, an explosion, problems with the product,
or injury.
Remove all foreign substances such as dust or water from the power plug terminals and
contact points using a dry cloth on a regular basis.
• Unplug the power plug and clean it with a dry cloth.
• Failing to do so may result in electric shock or fire.
Plug the power plug into the wall socket in the right direction so that the cord runs towards
the floor.
• If you plug the power plug into the socket in the opposite direction, the electric wires
within the cable may be damaged and this may result in electric shock or fire.
SAVE THESE INSTRUCTIONS
6 English
WA771)0] WA481771)0A_ _ 03520D 01 ENindd 6 2(115/4/16 9:38:29
This appliance must be properly grounded.
Do not ground the appliance to a gas pipe, plastic water pipe, or telephone line.
• Improper grounding may result in electric shock, fire, an explosion, or problems with the
product.
• Never plug the power cord into a socket that is not grounded correctly. Make sure the
socket you use is grounded in accordance with local and national codes.
Do not install this appliance near a heater or flammable material.
Do not install this appliance in a humid, oily, or dusty location, or in a location exposed to
direct sunlight or water (rain drops).
Do not install this appliance in a location where gas may leak.
• This may result in electric shock or fire.
Plug the power plug into the wall socket firmly. Do not use a damaged power plug, damaged
power cord, or loose wall socket.
• This may result in electric shock or fire.
Do not pull or excessively bend the power cord.
Do not twist or tie the power cord.
Do not hook the power cord over a metal object, place a heavy object on the power cord,
insert the power cord between objects, or push the power cord into the space behind the
appliance.
• This may result in electric shock or fire.
Do not pull the power cord when unplugging the power plug.
• Unplug the power plug by holding the plug.
• Failing to do so may result in electric shock or fire.
If the power plug or power cord are damaged, contact your nearest service center.
Installation cautions
/'_ CAUTION
Position the appliance so that the power plug is easily accessible.
• Failing to do so may result in electric shock or fire due to electric leakage.
Install your appliance on a level and hard floor that can support its weight.
• Failing to do so may result in abnormal vibrations, noise, or problems with the product.
SAVE THESE iNSTRUCTiONS
English
WA7700J WA48J7700AW 03520D 01 ENindd 7 2015/4/16 9:38:30
Safety information
Unplug the power plug when the appliance is not being used for long periods of time or
during a thunder/lightning storm.
• Failing to do so may result in electric shock or fire.
Critical usage warnings
/_ WARNING
If the appliance is flooded, cut the Dower immediately and contact your nearest service
center.
If the appliance emits a strange noise, a burning smell, or smoke, unplug the power plug
immediately and contact your nearest service center.
• Failing to do so may result in electric shock or fire.
In the event of a gas leak (such as propane gas, LP gas, etc.), ventilate the area immediately.
Do not turn any appliance or light on or off.
• Do not use a ventilating fan.
• A spark may result in an explosion or fire.
Do not wash items contaminated with gasoline, kerosene, benzene, paint thinner, alcohol or
other flammable or explosive substances.
• This may result in electric shock, fire, or an explosion.
Do not force the washer lid open while the washer is operating (high-temperature washing/
drying/spinning).
• Water flowing out of the washer may cause burns or cause the floor to be slippery.
This may result in injury.
• Forcing the lid open can damage the product or cause injury.
Make sure to remove the packaging (sponge, styrofoam) attached to the bottom of the
washer before using it.
Do not insert your hand under the washer.
• This may result in injury.
Do not touch the power plug with wet hands.
• This may result in electric shock.
Do not turn the appliance off by unplugging the power plug while the washer is in operation.
SAVE THESE INSTRUCTIONS
8 English
\\TA7700] \\TA4817700A_S ' 03520D 01 ENindd 8 2015/4/16 9:38:30
• Plugging the power plug into the wall socket again may cause a spark and result in
electric shock or fire.
Keep all packaging materials well out of the reach of children, as packaging materials can be
dangerous to children.
o
If a child places a bag over their head, the child may suffocate.
Do
not let children or infirm persons use this washer unsupervised.
o
Failing to do so may result in electric shock, burns or injury.
Do
not insert your hand or a metal object under the washer while it is operating.
o
This may result in injury.
Do
not attempt to repair, disassemble, or modify the appliance yourself.
o
Do not use any fuse (such as copper, steel wire, etc.) other than the standard fuse.
o
If you need to repair or reinstall the appliance, contact your nearest service center.
o
Failing to do so may result in electric shock, fire, problems with the product, or injury.
If any foreign substance such as water enters the appliance in any area other than the tub,
unplug the power plug and contact your nearest service center.
• Failing to do so may result in electric shock or fire,
If the water supply hose comes loose from the faucet and floods the appliance, unplug the
power plug.
• Failing to do so may result in electric shock or fire.
Usage cautions
/_ CAUTION
If the washer is contaminated by a foreign substance such as detergent, dirt, food waste, etc.,
unplug the power plug and clean the washer using a damp, soft cloth.
• Failing to do so may result in discoloration, deformation, damage or rust.
The clear portion of the lid can be broken by a strong impact. Take care when using the
washer.
• If the clear portion is cracked or broken, it may result in injury.
After a water supply failure or when reconnecting the water supply hose, open the faucet
slowly.
SAVE THESE INSTRUCTIONS
English
\\TA771)0] \\TA48177I)0A_S ' 03520D 01 ENindd 9 2015/4/16 9:38:30
Safety information
Open the faucet slowly after a long period of non-use.
• The air pressure in the water supply hose or the water pipe may result in damage to a
part or in water leakage.
If a drain information occurs during an operation, check if there is a draining problem.
• If the washer is used when it is flooded because of a draining problem, it may result in
electric shock or fire due to electric leakage.
Do not insert your hand under the washer.
• This may result in injury.
Insert the laundry into the washer completely so that laundry does not get caught in the lid.
• If laundry gets caught in the lid, it may result in damage to the laundry or the washer, or
result in water leakage.
Ensure that the faucet is turned off when the washer is not being used.
• Ensure that the water supply hose connectors are properly tightened.
• Failing to do so may result in property damage or injury.
Open the faucet and check if the water supply hose connector is firmly tightened and that
there is no water leaking before using the product.
• If the water supply hose connectors are loose, it may result in water leakage.
Do not stand on top of the appliance or place objects (such as laundry, lighted candles,
lighted cigarettes, dishes, chemicals, metal objects, etc.) on the appliance.
• This may result in electric shock, fire, problems with the product, or injury.
Do not operate the appliance with wet hands.
• This may result in electric shocK.
Do not spray volatile material such as insecticide onto the surface of the appliance.
• As well as being harmful to humans, it may also result in electric shock, fire, or problems
with the product.
Do not place an object that generates a electromagnetic field near the washer.
• This may result in injury due to a malfunction.
Since the water drained during a high-temperature wash or drying cycle is hot, do not touch
the water.
• This may result in burns or injury.
For waterproof fabrics, only use the WATERPROOF cycle.
SAVE THESE INSTRUCTIONS
10 English
WA7700] WA48J7700AW 03520D 01 ENindd 10 2015/4/16 9:38:30
Do not use other cycles for waterproof fabrics.
This may result in injury or damage to the washer, walls, floor, or clothing due to
abnormal vibrations.
o
Set the temperature and spin according to the attached care label.
Do
not operate the washer when the detergent dispenser is removed.
o
This may result in electric shock or injury due to water leakage.
Do
not insert your hand into the detergent dispenser after opening it.
o
This may result in injury as your hand may be caught.
Do
not place any non-laundry objects, such as shoes, food waste, or animals into the washer.
o
This can cause abnormal vibrations that can damage the washer, and, in the case of pets,
cause severe injury or death.
Do not press the buttons using sharp objects such as pins, IKnifes, fingernails, etc.
• This may result in electric shock or injury.
Do not wash laundry contaminated by oils, creams, or lotions usually found in slKincare shops
or massage clinics.
• This may result in the rubber seal becoming deformed and water leakage,
Do not leave metal objects (safety pins, hair pins, etc.) or bleach in the tub for long periods of
time.
• This may cause the tub to rust.
• If rust appears on the surface of the tub, apply a neutral cleansing agent to the surface
and use a sponge to clean it. Never use a metal brush.
Do not use dry cleaning detergent directly in the tub and do not wash, rinse, or spin laundry
contaminated by dry cleaning detergent.
• This may result in spontaneous combustion or ignition due to heat from the oxidation of
the oil.
Do
not use hot water from water cooling/heating devices.
o
This may result in problems with the washer.
Do
not use natural hand-washing soap in the washer.
o
If it hardens and accumulates inside the washer, it may cause problems with the product,
discoloration, rust, or bad odors.
Do not wash large laundry items such as bedding in the washing net.
• Failing to do so may result in injury due to abnormal vibrations.
SAVE THESE iNSTRUCTiONS
English
11
\\TA771)0] \\TA481771)0A_S ' 03520D 01 ENindd 11 2015/4/16 9:38:30
Safety information
• Place smaller items, such as lace socks and lingerie in the washing net.
Do not use hardened detergent.
• If it accumulates inside the washer, it may result in water leakage.
Do not wash throw rugs or doormats.
• If you wash throw rugs or doormats, the sand will accumulate inside the washer. It may
result in information such as no draining.
CrRical cleaning warnings
/_ WARNING
Do not clean the appliance by spraying water directly onto it.
Do not use the strong acid cleaning agent.
Do not use benzene, paint thinner, or alcohol to clean the appliance.
• This may result in discoloration, deformation, damage, electric shock, or fire.
Before cleaning or performing maintenance, unplug the appliance from the wall socket.
• Failing to do so may result in electric shock or fire.
SAVE THESE INSTRUCTIONS
12 English
\\TA7700] \\TA4817700A_S ' 03520D 01 ENindd 12 2015/4/16 9:38:30
Installation
Follow these instructions carefully to ensure proper installation of the washer and to prevent
accidents when using it.
Unpacking your washer
Unpack your washer and inspect it for shipping damage. Make sure you have received all the
items shown below. If your washer was damaged during shipping, or you do not have all of
the items, contact !-800-SAMSUNG (!-800-726-7864).
To prevent personal injury or strain, wear protective gloves whenever lifting or carrying the
unit.
//_ WARNING
Packing materials can be dangerous to children; Keep all packing material (plastic bags,
polystyrene, etc.) well out of children's reach.
/'iX, CAUTION
When unpacking the washer, 2 person
collaboration is needed. To remove the
cushion bottom of the packing materials,
forward dumping is strictly prohibited.
X
English 13
\\TA7700] \\TA4817700A_S ' 03520D 01 ENindd 13 2015/4/16 9:38:30
Installation
Overview of your washer
Make sure all the parts are included in the product package. If you have a problem with
the washer or the parts, contact a local Samsung customer center or the retailer.
14 English
o_
WA7700J_WA48J7700AW-03520D-01_EN.indd 14 2015/4/16 9:38:31
01 Drain hose
02 Hose guide
03 Lid
04 Built-in sink
07 Leveling feet
10 Control panel
Parts supplied
Hose guide
Parts not supplied
05 Tub
08 Water hose (Cold)
11 Detergent drawer
User manual
06 Water Jet
09 Water hose (Hot)
12 Power cord
Plastic zip hose tie Water intake cap
Water supply hoses
Tools needed for installation
Wrench Flat screwdriver Leveller
NOTE
• If you lose an accessory and want to purchase a replacement, contact the Samsung
service center (!-800-SAMSUNG (!-800-726-7864)).
• The design of the parts and accessories may differ from the pictures above.
Their design is subject to change without notice for product improvement.
• Do not reuse old hoses. Only use new water supply hoses when you install the washer.
Old water supply hoses can leak or burst causing flooding and property damage.
• Confirm that there are rubber washers inside each coupling of the water supply hoses.
English 15
WA7700J WA48J7700AW 03520D 0] ENindd 15 2(}15/4/16 9:38:32
Installation
Basic location requirements
Electrical
• !20 Volt 60 Hz !5 AMP fuse or circuit
breaker.
• Individual branch circuit serving only
your Washer is recommended.
• Your washer is equipped with a power
cord.
/!X, CAUTION
Never use an extension cord.
Grounding
Electrical grounding is required for this
appliance.
This appliance must be grounded. In
the event of malfunction or breakdown,
grounding will reduce the risk of electric
shock by providing a path of least resistance
for electric current.
This appliance is equipped with a power
cord having a three-prong grounding plug
for use in a properly installed and grounded
outlet.
The plug must be plugged into an
appropriate outlet that is properly installed
and grounded in accordance with all local
codes and ordinances.
z_ WARNING
An improperly connected equipment-
grounding conductor can increase the risk
of electrical shock. Check with a qualified
electrician or serviceman if you are not sure
whether the appliance is properly grounded.
Do not modify the plug provided with the
appliance- if it does not fit the outlet, have
a proper outlet installed by a qualified
electrician.
Important safety precautions
To prevent unnecessary risk of fire,
electrical shock or personal injury, all wiring
and grounding must be done in accordance
with the National Electrical Code ANSI/
FNPA, No.70 Latest Revision and local
codes and ordinances. It is the personal
responsibility of the appliance owner to
provide adequate electrical service for this
appliance.
//iX CAUTION
Never connect the ground wire to plastic
plumbing lines, gas lines, or hot water pipes.
Water
To correctly fill your Washer in the proper
amount of time, water pressure of 20 to
!16psi (!37 to 800kPa) is required.
Water pressure less than 20 psi may cause
water valve failure, or may not allow the
water valve to shut off completely, or may
extend the fill time beyond what your
Washer controls allow, causing your Washer
to turn off. A time limit is built into the
controls to prevent flooding in your home if
a hose becomes loose.
16 English
WA7700J WA48J7700AW 03520D 0] ENindd 16 2(}15/4/16 9:38:32
The water faucets must be within 4 feet
(!22 cm) to the back of your Washer to
match the inlet hoses provided with your
Washer.
NOTE
Accessory inlet hoses are available in
various lengths up to !0 feet (275 cm) for
faucets that are further away from the back
of your washer.
To avoid the possibility of water damage:
• Have water faucets easily accessible.
• Turn off faucets when the washer is not
in use.
• Periodically check that there is no
leakage from the water inlet hose
fittings.
WARNING
Check all connections at the water valve and
faucet for leaks
Drain facility
The recommended height of the standpipe
is 39 in (99 cm). The drain hose must be
routed through the drain hose clip to the
standpipe. The standpipe must be large
enough to accept the outside diameter of
the drain hose. The drain hose is attached to
the washer at the factory.
Never install your washer on a platform or
weakly supported structure.
Location considerations
Do not install your washer in areas where
water may freeze, since your washer will
always retain some water in its water valve,
pump, and hose areas. Frozen water can
damage the belts, the pump, hoses, and
other components.
Alcove or closet installation
Minimum clearances for closet and alcove
installations:
Sides
.... 25mm front 5! mm
,,.,_,.., 6 in / 21_in /
If the washer and dryer are installed
together, the closet front must have at least
a 72 in2(465 cm2)unobstructed air opening.
Your washer alone does not require a
specific air opening.
1 in / CloSet 2 in /
1_52mm 533 mm
Flooring
For best performance, you must install
your washer on a solidly constructed floor.
Wood floors may need to be reinforced to
minimize vibration and/or unbalanced load
situations. Carpeting and soft tile surfaces
are contributing factors to vibration which
can cause your washer to move slightly
during the spin cycle.
English 17
\\TA771)0] \\TA481771)0A_S' 03520D 01 ENindd 17 2015/4/16 9:38:32
Installation
Recessed area Side view - closet or confined area
_7¸¸¸ :::::::::::: <::::::::::::::::: :=:5:5:5:5:5:5:5:5:5:5:5:5 :F¸
7
A ! in (2.5 cm)
B 27.0 in (68.6 cm)
2! in (53.3 cm)
B 2 in (5.! cm)
C 29.3 in (74.4 cm)
D 6 in (!5.2 cm)
Gap between end of water
valve and the wall
• Case !. Assemble supply
i _I i i
ii i i i
i i iii i_i
i i i
hose after installing : Over
3.9 in (!0 cm).
• Case 2. Assemble supply
hose before installing :
Over 2.8 in (7 cm).
18 English
\\TA771)0] \\TA481771)0A_V 03520D 01 ENindd 18 2015/4/16 9:38:32
Required dimensions for Installation
r
...................... l
_ J
27.0 in (68.6 cm)
39.2 in (99.5 cm)
44.2 in (!!2.3 cm)
58.! in (!47.6 cm)
48.0 in2 (3!0.0 cm2)
24.0 in2 (!55.0 cm2)
3.0 in (7.6 cm)
29.3 in (74.4 cm)
NOTE
44.2 in (!!2.3 cm)
" Required spacing
English 19
\VA7700] \VA4817700A_' 03520D 01 ENindd 19 2015/4/16 9:38:33
Installation
Important note to installer
Please read the following instructions carefully before installing your washer.
These instructions should be retained for future reference.
We recommend you hire a professional to install this washer.
Installation flow chart
Removing the
Selecting a
location
Running a test cycle
RunRinse±SpinWi_h
Smallamount Of -_ Running
laundry (aboUt 85 Calibration Mode
towels) as a test Cycle
shipping bolts
(Front loading
washers only)
Connecting the
water anddrain
p,
Adjusting the
leveling feet
Powering your
washing machine
Finishing the
installation
YES y
Check again before steps.
Step-by-step installation
STEP 1 Selecting a location
NOTE
Before you install the washer, make sure the location:
• Has a hard, level surface without carpeting or flooring that may obstruct ventilation.
• Is away from direct sunlight.
• Has adequate ventilation.
• Is not exposed to freezing temperatures (temperatures under 32 °F or 0 oC).
• Is away from heat sources such as oil or gas.
• Has enough space so that the washer doesn't rest on its power cord.
20 English
\\TA771)0] \\TA481771)0A_S' 03520D 01 ENindd 20 2015/4/16 9:38:33
STEP 2 Connecting the water supply hose
/_ CAUTION
Before installing the water supply hoses,
make sure there are rubber gaskets (B)
inside the couplings (A) at both ends of each
new water hose. Installing the water supply
hoses without rubber gaskets can cause
water leakage.
/_ CAUTION
When you initially install the washer, be
sure to use new hoses. Failing to do so may
result in a water leakage or overflow and
may damage your property.
/'_ CAUTION
Do not connect multiple water supply hoses
together to increase the length of the supply
hose. Hoses connected this way can leak
and the leakage can cause electrical shock. If
a hose is too short, replace the hose with a
longer, high pressure hose.
English 21
WA7700] WA4817700A_ ' 03520D 01 ENindd 21 2015/4/16 9:38:33
Installation
Connect the ends of the water supply
hoses to the hot (B) and cold (A) faucets.
2.
Tighten the fittings by hand until they
are snug, and then tighten them an
additional two-thirds of a turn with a
wrench.
/!_ CAUTION
When you fasten the fittings, do not fasten
them too tightly or apply tape or sealant to
the faucets or water supply intakes. This can
damage the fittings.
NOTE
After you have connected the water supply
hoses to the faucets, ensure that they are
connected correctly by pulling the water
supply hoses downwards.
3_ Place the unconnected ends of the hoses
into a bucket and open the faucets
connected to the two water supply hoses
for 10 or !5 seconds to remove any
foreign substances from the hoses. Close
the faucets before continuing.
22 English
\\TA771)0] \\TA481771)0A_S' 03520D 01 ENindd 22 2015/4/16 9:38:34
& Connect the ends of the water supply
hoses to the water supply intake
connections at the back of the washer.
Z_ CAUTION
The water supply hose connected to the hot
faucet must be connected to the hot water
supply intake and the water hose connected
to the cold faucet must be connected to the
cold water supply intake.
5,
Tighten the fittings by hand until they
are snug, and then tighten them an
additional two-thirds of a turn with a
wrench.
NOTE
To ensure the correct water usage, connect
both the hot and cold water faucets. If either
or both are not connected, an "4C" (no fill)
code can be displayed.
NOTE
If you do not want to use the hot water
supply hose, insert the water intake cap
into the hot water supply intake hole. In
this case, you must select the Tap Cold
for the water temperature. If you select
the Tap Cold, all the lamps for the water
temperature options are turned off.
//_ CAUTION
Confirm that the water supply hoses are not
twisted or bent. If the hoses are twisted or
bent, the hoses can leak and cause electric
shock due to the water leakage.
6, Turn on the hot and cold water supplies
and check all the water supply intake
connections and the faucets for water
leaks.
English 23
\\TA7700] \\TA4817700A_S ' 03520D 01 ENindd 23 2015/4/16 9:38:34
Installation
STEP 3
Connecting the drain hose
The end of the drain hose can be positioned
in three ways:
Over the edge of a wash basin
Secure the hose guide (A) to the side of the
basin wall with a hook or to the tap with
a piece of string to prevent the drain hose
from moving.
In a standpipe or laundry tub
The standpipe (B) and laundry tub (C) must
be no shorter than 39 in (99 cm)* and no
longer than 96 in (245 cm)*.
_ NOTE
• Make sure that the connection between
the drain hose and the standpipe is not
airtight.
• D: Hose retainer, E:Tie strap
24 English
\\TA771)I)] \\TA481771)0A_S ' I)3520D 01 ENindd 24 2015/4/16 9:38:35
NOTE
Connect the hose guide (A) within 4 in (!0
cm) _from the end of the drain hose. If the
drain hose is extended more than 4 in (!0
cm) beyond the end of the hose guide, mold
or microorganisms could spread to the
inside of the washer.
NOTE
The drain hose can be installed to a 95
in (245 cm) maximum, but the draining
capability can be reduced at this height.
It can cause the washer to have an odor
because of remaining water in the drain
system.
NOTE
If the drain hose is installed below 39 in (99
cm), water can be drained in cycles due to a
siphon phenomenon. It causes the washer to
display "4C".
STEP4
Leveling your washer
See if the washer is level by checking the
position of the tub:
1, Slide the washer into position.
2, Open the lid of the washer, and pour
the water into the tub to just below the
pulsator level.
NOTE
J
WA48J _models have the Built-in sink over
the pulsator level. That's why the level is not
revealed. Open the Built-in sink and check
the level with eyes.
English 25
\\TA771)()] \\TA481771)0A_S' 1)3520D 01 ENindd 25 2015/4/16 9:38:35
Installation
3, If the washer is level, the pulsator (A) is
positioned at the center of the water as
shown in the figure.
If not, level your washer by turning
the front leveling feet clockwise or
counterclockwise as necessary.
NOTE
Turn the front leveling feet clockwise (B) to
lower the washer, and counterclockwise (C)
to raise the washer.
STEP 5
26 English
\\TA7700] \\TA4817700A_S ' 03520D 01 ENindd 26 2015/4/16 9:38:35
Powering your washer
Plug the power cord into a 3-prong,
well grounded !20 volt 60 Hz approved
electrical outlet protected by a !5-amp fuse
or comparable circuit breaker.
Your washer is grounded through the third
prong of the power cord when plugged into
a three-prong grounded electrical outlet.
Test run
Make sure that you install your washer
correctly by running the Rinse+Spin after
the installation is complete.
STEP 6 Running a test cycle
Run a test cycle as follows to check if your washer is properly installed.
1. Load about 6 pounds of laundry into the tub.
2, Press Power to turn on your washer.
3. Select Rinse+Spin by turning the Cycle Selector.
4. Press Start/Pause to start the test cycle.
5. The washer should not rock or vibrate excessively when water is supplied or when
washing or spinning, and should drain well during the spin cycle.
NOTE
If water leaks while water is being supplied or drained, check the water connections. Refer to
the "STEP 2 Connecting the water supply hose" section on page 2! for instructions.
NOTE
If the washer rocks and vibrates excessively, level your washer again. Refer to the "STEP
4 Leveling your washer" section on page 25 for instructions.
STEP7 Calibration Mode
Your Samsung washer detects the laundry weight automatically.
For more accurate weight detection, please run Calibration Mode after the installation.
To run Calibration Mode, follow these steps:
1. Remove laundry or any contents in the machine.
2, Press and hold Temp. and Delay End simultaneously for at least 3 seconds when the
power is turned on.
3. Press Start/Pause to activate Calibration Mode.
4. The pulsator rotates clockwise and counterclockwise approximately 1 minute.
5. When Calibration Mode is finished, "End" appears on the display, and the washer
automatically turns off. The washer is now ready for use.
English 27
WA7700] WA48J7700AW 03520D 01 ENindd 27 2015/4/16 9:38:36
Operating instructions
z_ WARNING
To reduce the risk of fire, electric shock, or injury to persons when using your appliance,
follow basic precautions, including the following:
Loading your washer
• You can fill the tub with dry, unfolded
clothes, but DO NOT OVERLOAD the tub
any more than 3/4 full.
• Overloading may reduce washing
efficiency, cause excess wear, and
possibly cause creasing or wrinkling of
the load.
• Wash delicate items such as bras,
hosiery, and other lingerie in the
Delicates cycle with similar lightweight
items.
• When washing big bulky items or a
few smaller items that don't fill the tub
completely - a rug, a pillow, stuffed toys,
or one or two sweaters, for example
- add a few towels to improve spin
performance.
• Do not insert bulky items except for
Bedding in this cycle.
NOTE
During the spin cycle, the washer may add
additional water to redistribute the clothes
and correct an imbalance inside the drum.
• When washing heavily soiled loads, do
not overload your washer to ensure
good cleaning results.
To add a forgotten item:
1, Press Start/Pause to pause the washer.
2, Wait for the door to unlock automatically, and then open the door.
3, Add the item, close the door, and then press Start/Pause. The cycle will resume.
28 English
\\rA771)()] \\rA481771)(/A_' ()3520D 01 ENindd 28 2(115/4/16 9:38:36
Getting started
1. Load your washer.
2. Add liquid (or powder) detergent and additives to the dispenser (see the "Detergent use"
section on page 41).
3. Select the appropriate cycle and options for the load (see the "Washing a load of laundry"
section page 30).
4. Close the lid.
5. Press Start/Pause.
6. The Wash Indicator illuminates.
7. The estimated cycle time will appear in the display.
The time may fluctuate to indicate the time remaining in the cycle.
NOTE
The actual time required for a cycle may differ from the estimated time in the display
depending on the water pressure, water temperature, detergent, and laundry.
8. Before your washer starts to fill, it will make a series of clicking noises to check the door
lock and do a quick drain.
NOTE
• When the cycle is complete, the_ Door Lock indicator will go out and "End" will appear
in the display.
• Pressing Power cancels the cycle and stops your washer.
• The Wash, Rinse, and Spin indicators will illuminate during those portions of the cycle.
English 29
\\rA771)()] \\rA481771)(/A_' ()3520D 01 ENindd 29 2(115/4/16 9:38:36
Washing a load of laundry
z_ WARNING
To reduce the risk of fire, electric shock, or injury to persons, read the IMPORTANT SAFETY
INSTRUCTIONS before operating this appliance.
Control panel
r
HEAVY DUTY_
NORMAL
PRESS
*(Hold 3 sec)
COLORS/DARKS
HEAVY
SUPER SPEED
NORMAL
_PERM PRESS
:::::_ QUICK WASH
: ] _ - SPIN
VE WEAR
UICK WASH
RINSE+SPIN
AquaJet"
/
::¢; .... L/___. RINSE+SPIN
AquaJet, _
Turn the Cycle Selector to select the desired cycle. The indicator by
CYcle Selector the cycle name lights up.
WEAR
I Hot I High _!
1 Eco Warm 1 Low 1 Normal
1 Warm 1 Medium 1 Heavy
I Cold I NO Spin I Light
o TapCold
%m'_....... "
*(Hold 3 sec)
I Hot I High
I Warm I Medium I Heavy
I Eco Warm I Low I Normal
I Cold 1 No Spin 1 Light
o TapCold
*Sound _*Child Lock ,.J *Smart Care
I POWERI
I [>11I
I gTART I
I_1
Provides instructions and diagnostics while keeping you updated on
the cycle status and time remaining.
30 English
\VAT700] \VA481770gAl_' 0352gD g] ENindd 30 2(115/4/16 9:38:36