Our product complies with
“The Restriction Of the use of
certain Hazardous Substances
equipment”, and we do not use the 6
hazardous materials- Cadmium(Cd), Lead
(Pb), Mercury (Hg), Hexavalent Chromium
(Cr
Poly Brominated Diphenyl Ethers(PBDEs)in our products.
Owner’s Instruction Book
Before operating the unit, please read this Instruction
Book thoroughly, and retain it for future reference.
Use only approved battery packs.
Otherwise, there is a danger of overheating, fire or explosion.
Samsung is not responsible for problems occurring due to
using unapproved batteries.
in electrical and electronic
+6
), Poly Brominated Biphenyls (PBBs),
This product meets the intent of
Directive 89/ 336 CEE, 73/ 23 CEE, 93/ 68 CEE.
VP - D361(i)/D361W(i)/
D362(i)/D363(i)/
D364W(i)/D365W(i)
AF
CCD
LCD
AD68-00970T
ENGLISH
Contents
Notes and Safety Instructions ...............................................5
Getting to Know Your Camcorder ........................................7
Features .....................................................................................................................................7
Accessories Supplied with Camcorder......................................................................................8
Front & Left View .......................................................................................................................9
Left Side View ..........................................................................................................................10
Right & Top View ......................................................................................................................11
Please rotate the LCD Screen carefully as
illustrated.
Over rotation may cause damage to the inside
of the hinge that connects the LCD Screen to
the Camcorder.
1. Open the LCD Screen 90 degrees to the
Camcorder with your finger.
2. Rotate it to the best angle to record or play.
■
If you rotate the LCD Screen 180
degrees to the lens side, you can close
the LCD Screen with it facing out.
■
This is convenient during playback operations.
[Note]
Refer to page 29 to adjust brightness and colour of the LCD Screen.
Notes regarding the LCD Screen, Viewfinder, Lens
1. Direct sunlight can damage the LCD
Screen, the inside of the Viewfinder or
the Lens.
Take pictures of the sun only in low light
conditions, such as at dusk.
2. The LCD Screen has been manufactured
using high precision technology.
However, there may be tiny dots (red,
blue or green in colour) that appear on the LCD Screen. These dots
are normal and do not affect the recorded picture in any way.
3. Do not pick up the Camcorder by holding the Viewfinder, LCD Screen
or Battery Pack.
4. Applying excessive force to the Viewfinder may damage it.
Notes regarding the Video Head Cleaning
■
To ensure normal recording and a clear picture, clean the video
heads regularly.
If a square block-shape distorts playback, or only a blue screen is
displayed, the video heads may be dirty.
If this happens, clean the video heads with a dry type cleaning
cassette.
■
Do not use a wet-type cleaning cassette. It may damage the video
heads.
180 degrees (max.)
LCD Open Knob
90 degrees
to the Camcorder
90 degrees (max.)
■
■
1. 90
2. .
[]
■
■
■
LCD 180
LCD
29
1.
2.
3.
4.
55
ENGLISH
Notes and Safety Instructions
Notes regarding Camcorder
■
Do not leave the Camcorder exposed to high temperatures (above 60 °C or 140 °F).
For example, in a parked car in the sun or exposed to direct sunlight.
■
Do not let the Camcorder get wet. Keep the Camcorder away from rain, sea
water, and any other form of moisture.
If the Camcorder gets wet, it may get damaged. Sometimes a malfunction due to
exposure to liquids cannot be repaired.
■
A sudden rise in atmospheric temperature may cause condensation to form
inside the Camcorder.
- When you move the Camcorder from a cold location to a warm location (e.g.
from outside to inside during the winter.)
- When you move the Camcorder from a cool location to a hot location (e.g.
from inside to outside during the summer.)
■
If the (DEW) protection feature is activated, leave the Camcorder for at least
two hours in a dry, warm room with the cassette compartment opened and the
Battery Pack removed.
Notices regarding Copyright
Television programmes, video tapes, DVD titles, films, and other programme
materials may be copyrighted.
Unauthorized copying of copyrighted material may be against the law.
All the trade names and registered trademarks mentioned in this manual or other
documentation provided with your Samsung product are trademarks or registered
trademarks of their respective holders.
Servicing & Replacement Parts
■
Do not attempt to service this Camcorder yourself.
■
Opening or removing covers may expose you to dangerous voltage or other hazards.
■
Refer all servicing to qualified service personnel.
■
When replacement parts are required, be sure the service technician has used
replacement parts specified by the manufacturer and having the same
characteristics as the original part.
■
Unauthorized substitutions may result in fire, electric shock or other hazards.
■
■
■
- (
)
■
(DEW)
(60 C 140 F)
DVD
■
■
■
■
■
.
66
ENGLISH
Getting to Know Your Camcorder
Features
■
Digital Data Transfer Function with IEEE1394
By incorporating the IEEE 1394 (i.LINK™: i.LINK is a serial data transfer protocol
and interconnectivity system, used to transmit DV data) high speed data
transport port, both moving and photo images can be transferred to a PC,
making it possible to produce or edit various images.
■
USB Interface for Digital Image Data Transfer
(VP-D362(i)/D363(i)/D364W(i)/D365W(i) only)
You can transfer images to a PC using the USB interface without an add-on card.
■
PHOTO
The PHOTO function lets you capture an object as a still, while in <Camera
mode>.
■
1200x Digital Zoom
Allows you to magnify an image up to 1200 times its original size.
■
Audio Enhancement
Provides more powerful sound by added Real Stereo and Audio Effect functionalities.
■
Colour TFT LCD
A high-resolution colour TFT LCD gives you clean, sharp images as well as the
ability to review your recordings immediately. A high-resolution colour TFT LCD
of 230K pixels supports 16:9 aspect ratio of VP-D361W(i)/D364W(i)/D365W(i).
■
Digital Image Stabilizer (DIS)
The DIS compensates for any handshake, reducing unstable images particularly
at high magnification.
■
Various Visual Effects
The Visual Effects allows you to give your films a special look by adding various
special effects.
■
Back Light Compensation (BLC)
The BLC function compensates for the bright background behind a subject you're
recording.
■
Program AE
The Program AE enables you to alter the shutter speed and aperture to suit the
type of scene/action to be filmed.
■
High Power Zoom Lens
Power Zoom lens allows users to magnify the subject clearly up to x33.
■
Digital Still Camera Function (VP-D363(i)/D364W(i)/D365W(i) only)
- Using Memory Card, you can easily record and playback standard photo
images.
- You can transfer standard photo images on the Memory Card to your PC
using the USB interface.
Moving image recording makes it possible to record video onto a Memory Card.
■
Multi Memory Card Slot (VP-D364W(i)/D365W(i) only)
Multi Memory Card slot is able to use Memory Stick (Duo), Memory Stick PRO,
MMC and SD.
■
Built-in Memory (VP-D365W(i) only)
You can use digital still camera functions without a separate external Memory
Card, using the built-in memory installed in your Camcorder.
(VP-D365W(i): 32MB)
■
IEEE1394
IEEE 1394 (i.LINKTM: i.LINK
■
USB (VP-D362(i)/D363(i)/D364W(i)/D365W(i))
■
) ,
PC ,
USB PC
<Camera mode> ().
■
1200x
■
■
TFT LCD
■
■
■
■
■
■
■
■
■
VP-D361W(i)/D364W(i)/D365W(i)
BLC
-
- USB PC
, /
(VP-D363(i)/D364W(i)/D365W(i))
(VP-D364W(i)/D365W(i))
Stick PRO, MMC
(VP-D365W(i))
1200
TFT LCD -
2316:9
()
(VP-D363(i)/D364W(i)/D365W(i))
and SD
33
Memory Stick (Duo), Memory
(VP-D365W(i):32MB)
77
ENGLISH
Getting to Know Your Camcorder
Accessories Supplied with Camcorder
Make sure that the following basic accessories are supplied with your
digital video camera.
Basic Accessories
1. Lithium Ion Battery Pack
2. AC Power Adapter
(AA-E8 TYPE)
3. AC Cord
4. Multi Cable
5. Instruction Book
6. Lithium Battery for Remote
Control
(VP-D363(i)/D364W(i)/
D365W(i) only) or Clock.
(TYPE: CR2025)
7. Remote Control
(VP-D363(i)/D364W(i)
/D365W(i) only)
8. USB Cable
(VP-D362(i)/D363(i)/
D364W(i)/D365W(i) only)
9. Software CD
(VP-D362(i)/D363(i)/
D364W(i)/D365W(i) only)
10.Lens Cover
11.Lens Cover Strap
1. Lithium Ion Battery Pack
7. Remote Control (VPD363(i)/D364W(i)/
D365W(i) only)
10. Lens Cover
2. AC Power Adapter
(AA-E8 TYPE)
5. Instruction Book
8. USB Cable (VPD362(i)/D363(i)/D364W(i)
/D365W(i) only)
11. Lens Cover Strap
3. AC Cord
1.
2.(AA-E8
6. Lithium Battery (CR2025)4. Multi Cable
3.
4.
5.
6.
(VP-
9. Software CD (VPD362(i)/D363(i)/D364W(i)/
D365W(i) only)
Remote Control (VP-D363(i)/D364W(i)/D365W(i) only)
1. PHOTO
2. START/STOP
3. SELF TIMER
4. ZERO MEMORY
5. PHOTO SEARCH
œœ
10.
1. PHOTO Button ➥page 57
2. START/STOP Button
3. SELF TIMER Button
➥page 38
4. ZERO MEMORY Button
➥page 37
5. PHOTO SEARCH Button
6. A.DUB Button ➥page 62
√√√√
7.
(FF) Button
œœœœ
8.
(REW) Button
√√
(PLAY) Button
9.
❙❙ / ❙❙
6. A.DUB
√√√√
7.
œœœœ
8.
(REW)
√√
(PLAY)
9.
√√
(Direction)
(FF)
√√
œœ
❙❙/ ❙❙
10.
11. F. ADV Button ➥page 60
12. ■ (STOP) Button
13.
14. SLOW (
15. DATE/TIME Button
16. X2 Button ➥page 60
17. W/T (Zoom) Button
18. DISPLAY Button
(Direction)
Button ➥page 59
❙❙
(STILL) Button
√√
❙
) Button
1.
2.
3.
4.
5.
6.
7.
8.
9.√√(PLAY)
10.
(VP-D363(i)/D364W(i)/D365W(i))
18. DISPLAY
17. W/T (Zoom)
16. X2
√√√√
œœœœ
œœ
(FF)
(REW)
❙❙ ❙❙
➥
➥
➥
√√
57
➥
15. DATE/TIME
14. SLOW(
13.
12. ■ (STOP)
11. F. ADV
38
37
62
➥
59
❙
❙❙
(STILL)
11.
12.
■ (STOP)
13.❙❙(STILL)
SLOW (
14.
15.
16. 2
17.
18.
√√
)
➥
60
√√
❙
)
➥
60
1313
ENGLISH
Preparation
Using the Hand Strap & Lens Cover
It is very important to ensure that the Hand Strap has been correctly
adjusted before you begin your recording.
The Hand Strap enables you to:
- Hold the Camcorder in a stable, comfortable position.
- Press the [Zoom] and [Start/Stop] button without having to change
the position of your hand.
Hand Strap
Adjusting the Hand
Strap
1. Insert the Hand Strap into the
Hand Strap Hook on the front
side of the Camcorder and pull its end through
the hook.
2. Insert your hand into the Hand Strap and
adjust its length for your convenience.
3. Close the Hand Strap.
Lens Cover
Attaching the Lens Cover
1. Hook up the Lens Cover with the Lens Cover
Strap as illustrated.
2. Hook up the Lens Cover Strap to the Hand
Strap, and adjust it following
the steps as described for the Hand Strap.
3. Close the Hand Strap.
Installing the Lens Cover after Operation
Press buttons on both sides of the Lens Cover, then
insert it to the Camcorder Lens.
123
12
23
1.
2.
3.
1.
2.
3.
1414
ENGLISH
MENU
CHG
QUICK
MENU
Preparation
Lithium Battery Installation
Lithium Battery Installation for the
Internal Clock
1. Remove the Battery Pack from the rear of
the Camcorder.
2. Open the Lithium Battery Cover on the rear
of the Camcorder.
3. Position the Lithium Battery in the Lithium
Battery Holder, with the positive ()
terminal face up.
Be careful not to reverse the polarity of the Battery.
4. Close the Lithium Battery Cover.
Lithium Battery Installation for the
Remote Control (VP-D363(i)/
D364W(i)/D365W(i) only)
1. Pull out the Lithium Battery Holder toward
the direction of the arrow
using instruments such as a pair of tweezers.
2. Position the Lithium Battery in the Lithium
Battery Holder, with the positive () terminal face up.
3. Reinsert the Lithium Battery Holder.
Precaution regarding the Lithium Battery
1. The Lithium Battery maintains the clock function and preset contents
of the memory; even if the Battery Pack or AC Power adapter is
removed.
2. The Lithium Battery for the Camcorder lasts about 6 months under
normal operation from time of installation.
3. When the Lithium Battery becomes weak or dead, the date/time
indicator will display <00:00 1.JAN.2006> when you set the
<Date/Time> to <on>. When this occurs, replace the Lithium Battery
with a new one (type CR2025).
4. There is a danger of explosion if Battery is incorrectly replaced.
Replace only with the same or equivalent type.
Warning: Keep the Lithium Battery out of reach of children. Should
a battery be swallowed, consult a doctor immediately.
1.
2.
3.
4.
VP-
D363(i)/D364W(i)/D365W(i)
1.
2.
3.
1.
2.6
3.
00:00 1. 1,2006
4.
1515
ENGLISH
Using the Lithium Ion Battery Pack
✤ Use SB-LSM80 or SB-LSM160 Battery Pack only.
✤ The Battery Pack may be charged a little at the time of purchase.
Charging the Lithium Ion Battery Pack
1. Turn the [Power] switch
to [Off].
2. Attach the Battery Pack to
the Camcorder.
3. Connect the AC Power
Adapter to an AC Cord
and connect the AC Cord
to a wall socket.
4. Connect the DC cable to the DC jack on the Camcorder. The charging
indicator will start to blink, showing that the Battery is charging.
5. Press and hold the DISPLAY button while charging and the
charging status will be displayed on the LCD for 7
seconds.
■
As indicated the battery level is given as reference
data for the user, it is the approximate estimation. It
may differ from Battery capacity and temperature.
6. When the Battery is fully charged, disconnect the Battery
Pack and the AC Power Adapter from the Camcorder.
Even with the Power switched Off, the Battery Pack will
still discharge.
Charging, Recording Times based on Model and Battery
Type.
✤ If you close the LCD
Screen, it switches off
and the Viewfinder
switches on
automatically.
✤ The continuous
recording times given
in the table
to the right are approximations.
Actual recording time depends on usage.
✤ The continuous recording times in the operating instructions are measured
using a fully charged Battery Pack at 77 °F (25 °C).
✤ Even when the Power switched Off, the Battery Pack will still discharge if it
is left attached to the device.
Blinking timeCharging rate
Once per secondLess than 50%
Twice per second50% ~ 75%
Three times per second75% ~ 90%
Blinking stops and stays on 90% ~ 100%
On for a second and Error - Reset the Battery
off for a secondPack and the DC Cable
BBaatttteerr yy cchhaarrggeedd
0%50%100%
Battery
SB-LSM80
SB-LSM160
(Option)
Time
Charging
time
Approx.
1hr 20min
Approx.
3hr
Recording time
LCD On
Approx.
1hr 20min
Approx.
2hr 40min
Viewfinder On
1hr 30min
Approx.
Approx.
1616
✤SB-LSM80SB-LSM160
✤
1.[Power]
2.
3.
Battery info
✤
✤
3hr
✤
✤
[Off]
F (25 C)
4.
5.
LCD LCD
77
SB-LSM80
SB-LSM160
120
50%
50% ~ 75%
75% ~ 90%
90% ~ 100%
LCD
120
3
240
130
3
ENGLISH
Preparation
The amount of continuous recording time available depends on;
- The type and capacity of the Battery Pack you are using.
- Ambient temperature.
- How often the Zoom function is used.
- Type of use (Camcorder/Camera/With LCD Screen etc.).
It is recommended that you have several batteries available.
Battery Level Display
The battery level display indicates the amount of power
remaining in the Battery Pack.
a. Fully chargedb. 20~40% used
c. 40~80% usedd. 80~95% used
e. Completely used (Blinking)
(The Camcorder will turn off soon, change the
battery as soon as possible.)
Battery Pack Management
■
The Battery Pack should be recharged in an environment between
32 °F (0 °C) and 104 °F (40 °C).
■
The life and capacity of the Battery Pack will be reduced if it is used
in temperatures below 32 °F (0 °C) or left in temperatures above 104
°F (40 °C) for a long period of time, even when it is fully recharged.
■
Do not put the Battery Pack near any heat source (i.e. fire or a
heater).
■
Do not disassemble, apply pressure to or heat the Battery Pack.
■
Do not allow the + and – terminals of the Battery Pack to be shortcircuited. It may cause leakage, heat generation, induce overheating
or fire.
(Blinking)
■
F (40 C)
■
■
■
■
LCD
a.b.20~40%
c.
40~80% d.80~95%
e.
32 F (0 C) 104
32 F (0 C)
32 F (0 C)104 F (40 C)
1717
ENGLISH
Preparation
Notes regarding the Battery Pack
■
Please refer to the Table on page 16 for approximate continuous
recording time.
■
The recording time is affected by temperature and environmental
conditions.
■
The recording time shortens dramatically in a cold environment. As
the environmental temperature and conditions vary.
■
The continuous recording times in the operating instructions are
measured using a fully charged Battery Pack at 77 °F (25 °C). The
remaining battery time may differ from the approximate continuous
recording times given in the instructions.
■
It is recommended to use original Battery Pack that is available at
SAMSUNG service centre.
When the Battery reaches the end of its life, please contact your local
dealer.
The batteries have to be dealt with as chemical waste.
■
Make sure that the Battery Pack is fully charged before starting to
record.
■
A brand new Battery Pack is not charged. Before using the Battery
Pack, you need to charge it completely.
■
Fully discharging a Lithium Ion Battery damages the internal cells.
The Battery Pack may be prone to leakage when fully discharged.
■
To preserve battery power, keep your Camcorder turned off when you
are not operating it.
■
If your Camcorder is in <Camera> mode, and it is left in <STBY>
mode without being operated for more than 5 minutes with a tape
inserted, it will automatically turn itself off to protect against
unnecessary battery discharge.
■
Make sure that the Battery Pack is fitted firmly into place.
Do not drop the Battery Pack. Dropping the Battery Pack may
damage it.
■
■
■
■
■
■
■
■
■
■
<Camera><STBY>
■
1818
ENGLISH
Q
U
I
C
K
M
E
N
U
P
L
A
Y
E
R
C
A
M
E
R
A
C
A
M
E
R
A
P
L
A
Y
E
R
C
A
M
E
R
A
P
L
A
Y
E
R
C
A
M
E
R
A
P
L
A
Y
E
R
C
A
M
E
R
A
P
L
A
Y
E
R
C
A
M
E
R
A
P
L
A
Y
E
R
C
A
M
E
R
A
P
L
A
Y
E
R
C
A
M
E
R
A
P
L
A
Y
E
R
C
A
M
E
R
A
P
L
A
Y
E
R
Preparation
Connecting a Power Source
✤ There are two types of power source that can be connected to your
Camcorder.
- The AC Power adapter and AC Cord: used for indoor recording.
- The Battery Pack: used for outdoor recording.
Using a Household Power Source
Connect to a house hold power source to use
the Camcorder without worrying about the
battery power. You can keep the Battery Pack
attached; the battery power will not be
consumed.
1. Turn the [Power] switch to [OFF].
2. Connect the AC Power adapter (AA-E8
Type) to the AC Cord.
3. Connect the AC Cord to a wall socket.
The plug and wall socket type may differ
according to your resident country.
4. Connect the DC cable to the DC jack of the Camcorder.
5. Set the Camcorder to each mode by holding down the tab on the
[Power] switch and turning it to the [CAMERA] or [PLAYER] mode.
About the Operating Modes
✤ The operating modes are determined by the position of the [Power]
switch and the [Mode] switch.
✤ Set the Operation Mode by adjusting [Power] switch and [Mode]
switch before operating any functions.
Mode Name
[Power] Switch
[Mode] Switch
(VP-D363(i)/D364W(i)
/D365W(i) only)
[Note]
■
The <M.Cam> and the <M.Player> Modes are only enabled on VPD363(i)/ D364W(i)/ D365W(i).
<Camera
Mode>
<Player
Mode>
<M.Cam
Mode>
Power Switch
<M.Player
Mode>
✤
1. [Power][OFF]
2.
3.
4.
5.[Power]
[CAMERA][PLAYER]
✤
✤
[Power]
[Mode]
VP-
D363(i)/D364W(i)
/D365W(i)
■
<M.Cam><M.Player>
[Power][Mode]
<Camera Mode>
<Player Mode>
[Power][Mode]
VP-D363(i)/ D364W(i)/ D365W(i)
AA-E8
<M.Cam Mode>
<M.Player Mode>
1919
ENGLISH
Preparation
Using the QUICK MENU
✤ QUICK MENU is used to access Camcorder functions by using the
[QUICK MENU] button.
✤ QUICK MENU provides easier access to frequently used menus without
using the [MENU] button.
✤ Functions available using the QUICK MENU are as below:
Camera Mode
■
Setting the Digital Image Stabilizer (DIS) ➥page 55
■
Programmed Automatic Exposure Modes (Program AE)
➥page 49
■
Setting the 16:9 Wide ➥page 54
■
Setting the White Balance (White Balance) ➥page 51
■
Setting the Shutter Speed (Shutter)- Only can be
operated by using the QUICK MENU ➥page 47
■
Setting the Exposure (Exposure)- Only can be operated
by using the QUICK MENU ➥page 47
■
Setting the Back Light Compensation (BLC) ➥page 41
M.Cam Mode
■
Setting the Memory Type (Memory Type) ➥page 70
■
Setting the White Balance (White Balance) ➥page 51
■
Setting the Photo Quality (Photo Quality) ➥page 71
■
Setting the Exposure (Exposure)- Only can be operated
by using the QUICK MENU ➥page 47
■
Setting the Back Light Compensation (BLC) ➥page 41
M.Player Mode
■
Setting the Memory Type (Memory Type) ➥page 70
■
Playing Moving Images (MPEG) on the Memory Card (M.
Play Select) ➥page 80
■
Deleting Photo Images and Moving Images (Delete)
➥page 76
■
Protection from accidental Erasure (Protect) ➥page 75
■
Marking Images for Printing (Print Mark) ➥page 84
For example: Setting the White Balance
1. Press the [QUICK MENU] button.
The quick menu list will appear.
2. Move the [Zoom] lever up or down to select <White Balance>, then press the [OK] button.
3. Move the [Zoom] lever up or down to select desired
mode (Auto, Indoor, Outdoor or Custom WB), then
press the [OK] button.
4. To exit, press the [QUICK MENU] button.
2020
1
2
4
DIS
Program AE
16:9 Wide
White Balance
Shutter
Exposure
BLC
OSD (On Screen Display) in M.Cam/M.Player Modes
(VP-D363(i)/D364W(i)/D365W(i) only)
1. Photo Quality
➥page 71
2. CARD (Memory
Card) Indicator
3. Image Counter (Total
number of
recordable photo
images)
4. Image Recording
and Loading
Indicator
5. Erase Protection
Indicator ➥page 75
6. Print Mark ➥page 84
7. Folder Number-File
Number ➥page 72
8. JPEG Image Size
9. Slide Show ➥page 74
OSD in M.Cam ModeOSD in M.Player Mode
34
46
2
3 min
No Memory Card !
1
[29]
00:00 1.JAN.2006
WT
[29]
…
†
Turning the OSD (On Screen Display) On/Off
urning OSD On/Off
T
Press the [DISPLAY] button on the left side control panel.
■
Each press of the button toggles the OSD function on and off.
■
When you turn the OSD off,
- In <Camera Mode>: The STBY, REC modes are always
displayed on the screen, even when the OSD is turned off.
- In <Player Mode>: When you press any Function Button, it is
displayed on the OSD for 3 seconds before it turns off.
Turning the Date/Time On/Off
To turn the Date/Time on or off, access the menu and change the
<Date/Time> mode. ➥page 30
2222
(
VP-D363(i)/D364W(i)/D365W(i) )
9
Slide
No Memory Card !
5
001
6
00:00 1.JAN.2006100-0002
2/46
800X600
OSD ()
OSD
/OSD ()
■
■
<Camera Mode>
<Player Mode>
[DISPLAY]
OSD
OSD
<Date/Time>
➥
30
8
7
1.
2.
3.
4.
5.
75
6.
7.
➥
8. JPEG
9.
➥
71
➥
➥
84
72
➥
74
ENGLISH
Initial Setting : System Menu Setting
Setting the Clock (Clock Set)
✤ Clock setup works in <Camera>/<Player>/<M.Cam>/<M.Player>
modes. ➥page 19
✤ The Date/Time is automatically recorded onto a tape. Before
recording, please set the <Date/Time>. ➥page 30
1. Set the [Power] switch to [CAMERA] or[PLAYER].
2. Set the [Mode] switch to [TAPE] or [MEMORY].
(VP-D363(i)/D364W(i)/D365W(i) only)
3. Press the [MENU] button.
■
The menu list will appear.
4. Move the [Zoom] lever up or down to select
4
Camera Mode
√System
Clock Set
Remote
Beep Sound
Language
Demonstration
<System>, then press the [OK] button.
5. Move the [Zoom] lever up or down to select
<Clock Set>, then press the [OK] button.
■
The year will highlight first.
6. Move the [Zoom] lever up or down to set
current <Year>, then press the [OK] button.
■
The month will be highlighted.
7. You can set the month, day, hour and minute
following the same procedure after setting the year.
8. Press the [OK] button after setting the minutes.
■
A message <Complete !> is displayed.
■
To adjust the clock, select the Year, Month,
Day, Hour or Min by pressing the [OK]
button, then move the [Zoom] lever to the up
or down to set respective values.
9. To exit, press the [MENU] button.
[ Notes ]
■
After the Lithium Battery loses its charge (after
5
8
Camera Mode
Clock Set
Remote
Beep Sound
Language
Demonstration
Camera Mode
Clock Set
Remote
Beep Sound
Language
Demonstration
about 6 months), the date/time appears on the
screen as <00:00 1.JAN.2006>.
■
You can set the year up to 2037.
■
If the Lithium Battery is not installed, any input data will not be
backed up.
✤
✤
√On
√On
√English
√On
Move SelectExit
Back
Adjust Select Exit
Back
Complete !
Move SelectExit
■
<Camera>/<Player>/<M.Cam>/<M.Player>
/ / )
➥
19
<Date/Time> </>➥ 30
1. [Power][CAMERA]
[PLAYER]
2.[Mode][TAPE] [MEMORY]
VP-D363(i)/D364W(i)/D365W(i)
3.[MENU]
MENUOKZOOM
■
4.[Zoom]<System> ()
[OK]
5.[Zoom]<Clock Set> (
1 JAN 2006
00 : 00
MENUOKZOOM
1 JAN 2006
00 : 00
…
†
6.[Zoom]
7.
8.[OK]
)[OK]
■
■
■
■
[Zoom]
[OK]
<Complete !> (!)
9.[MENU]
MENUOKZOOM
■
1. JAN,2006> (00:00 1. 1,2006)
■
2037
(
/
6<00:00
2323
ENGLISH
P
L
A
Y
E
R
C
A
M
E
R
A
C
A
M
E
R
A
P
L
A
Y
E
R
Initial Setting : System Menu Setting
Setting the Wireless Remote Control Acceptance
(Remote) (VP-D363(i)/D364W(i)/D365W(i) only)
✤ The Remote function allows you to enable or disable the remote
control for use with the Camcorder.
1. Set the [Power] switch to [CAMERA] or [PLAYER].
2. Set the [Mode] switch to [TAPE] or [MEMORY].
3. Press the [MENU] button.
■
The menu list will appear.
4. Move the [Zoom] lever up or down to select
<System>, then press the [OK] button.
5. Move the [Zoom] lever up or down to select
<Remote>, then press the [OK] button.
6. Move the [Zoom] lever up or down to select <On>
or <Off>, then press the [OK] button.
7. To exit, press the [MENU] button.
[ Note ]
If you set the <Remote> to <Off> in the menu and try
to use it, the remote control icon () will blink for 3
seconds on the LCD Screen and then disappear.
2424
1
4
Camera Mode
√System
Clock Set
Remote
Beep Sound
Language
Demonstration
✤ You can turn the Beep Sound on or off, when on, each press of a
button sounds a beep.
1. Set the [Power] switch to [CAMERA] or [PLAYER].
2. Set the [Mode] switch to [TAPE] or [MEMORY].
(VP-D363(i)/D364W(i)/D365W(i) only)
3. Press the [MENU] button.
■
The menu list will appear.
4. Move the [Zoom] lever up or down to select
<System>, then press the [OK] button.
5. Move the [Zoom] lever up or down to select
<Beep Sound>, then press the [OK] button.
6. Move the [Zoom] lever up or down to select <On>
or <Off>, then press the [OK] button.
7. To exit, press the [MENU] button.
1
4
6
Camera Mode
√System
Clock Set
Remote
Beep Sound
Language
Demonstration
Move SelectExit
Camera Mode
Back
Clock Set
Remote
Beep Sound
Language
Demonstration
Move SelectExit
()
<Camera>/<Player>/<M.Cam>/<M.Player>
✤
✤
/ / )
➥
19
[PLAYER]
3.[MENU]
■
4.[Zoom] <System> ()
√On
√On
√English
√On
MENUOKZOOM
5.[Zoom] <Beep Sound>
(
6.[Zoom]<On> <>
<Off> ()[OK]
7.[MENU]
Off
On
MENUOKZOOM
[Power][CAMERA]
[Mode][TAPE] [MEMORY]
VP-D363(i)/D364W(i)/D365W(i)
[OK]
)[OK]
(
/
2525
ENGLISH
C
A
M
E
R
A
C
A
M
E
R
A
P
L
A
Y
E
R
P
L
A
Y
E
R
Initial Setting : System Menu Setting
Setting the Shutter Sound (Shutter Sound)
(VP-D363(i)/D364W(i)/D365W(i) only)
✤ The Shutter Sound function works in both <Player> and <M.Cam>
modes. ➥page 19
✤ You can turn the Shutter Sound on or off, when on, with each press
of the [PHOTO] button the Shutter will sound.
1. Set the [Power] switch to [CAMERA] or [PLAYER].
2. If the [Power] switch is set to [CAMERA], set the[Mode] switch to [MEMORY].
If the [Power] switch is set to [PLAYER], set the
[Mode] switch to [TAPE].
3. Press the [MENU] button.
■
The menu list will appear.
4. Move the [Zoom] lever up or down to select
<System>, then press the [OK] button.
5. Move the [Zoom] lever up or down to select
<Shutter Sound>, then press the [OK] button.
6. Move the [Zoom] lever up or down to select <On>
or <Off>, then press the [OK] button.
7. To exit, press the [MENU] button.
2626
1
4
6
Player Mode
√System
Clock Set
Remote
Beep Sound
Shutter Sound
Language
✤ You can select the desired language to display the menu screen and
the messages.
1. Set the [Power] switch to [CAMERA] or [PLAYER].
1
2. Set the [Mode] switch to [TAPE] or [MEMORY].
(VP-D363(i)/D364W(i)/D365W(i) only)
3. Press the [MENU] button.
■
The menu list will appear.
4. Move the [Zoom] lever up or down to select
<System>, then press the [OK] button.
5. Move the [Zoom] lever up or down to select
<Language>, then press the [OK] button.
■
The available language options are listed.
6. Move the [Zoom] lever up or down to select desired
OSD language, then press the [OK] button.
■
The OSD language is refreshed in selected
4
Camera Mode
√System
Clock Set
Remote
Beep Sound
Language
Demonstration
language.
7. To exit, press the [MENU] button.
[ Note ]
The word <Language> in the menu is always indicated in English.
✤
✤
Move SelectExit
7.[MENU]
■
OSD (Language)
<Camera>/<Player>/<M.Cam>/<M.Player>
/ / )
➥
19
1.[Power][CAMERA]
[PLAYER]
2.[Mode][TAPE]
[MEMORY]
(VP-D363(i)/D364W(i)/D365W(i))
3.
[MENU]
■
√On
√On
√English
√On
MENUOKZOOM
4.[Zoom]<System> (),
5. [Zoom]<Language>
■
6.[Zoom]OSD
■
<Language>
[OK]
[OK]
[OK]
OSD
(
/
2727
ENGLISH
P
L
A
Y
E
R
C
A
M
E
R
A
C
A
M
E
R
A
P
L
A
Y
E
R
Initial Setting : System Menu Setting
Viewing the Demonstration (Demonstration)
✤ The Demonstration function may only be used in the
<Camera> mode without a tape inserted in the
Camcorder. ➥page 19
✤ Before you begin: Make Sure that there is no tape
inserted in the Camcorder. ➥page 32
✤ Demonstration automatically shows you the major
functions that are included with your Camcorder so
that you may use them more easily.
✤ The Demonstration operates repeatedly until the
Demonstration mode switched Off.
1. Set the [Power] switch to [CAMERA].
2. Set the [Mode] switch to [TAPE].
(VP-D363(i)/D364W(i)/D365W(i) only)
3. Press the [MENU] button.
■
The menu list will appear.
4. Move the [Zoom] lever up or down to select
<System>, then press the [OK] button.
5. Move the [Zoom] lever up or down to select
<Demonstration>, then press the [OK] button.
6. Move the [Zoom] lever up or down to select
<On>, then press the [OK] button.
7. Press the [MENU] button.
■
The Demonstration will begin.
8. To quit the Demonstration, press the [MENU] button.
[ Notes ]
■
The Demonstration function is automatically
activated when the Camcorder is left idle for
more than 10 minutes after switching to the
<Camera> mode (no tape is inserted in the
Camcorder).
■
2828
If you press other buttons (FADE, MF/AF, PHOTO,
EASY.Q) during the Demonstration mode, the
demonstration stops temporarily and resumes 10
minutes later if you do not operate any other
functions.
(VP-D361(i)/D362(i)/D363(i)) / 2.7 inch wide (VP-D361W(i)/D364W(i)
/D365W(i)) colour Liquid Crystal Display (LCD) Screen, which
enables you to view what you are recording or playing back directly.
✤ Depending on the conditions under which you are using the
Camcorder (indoors or outdoors for example), you can adjust;
- <LCD Bright>
- <LCD Colour>
1. Set the [Power] switch to [CAMERA] or [PLAYER].
2. Set the [Mode] switch to [TAPE] or [MEMORY].
(VP-D363(i)/D364W(i)/D365W(i) only)
3. Press the [MENU] button.
■
The menu list will appear.
4. Move the [Zoom] lever up or down to select
<Display>, then press the [OK] button.
5. Move the [Zoom] lever up or down to select the item
you want to adjust (LCD Bright or LCD Colour),
then press the [OK] button.
6. Move the [Zoom] lever up or down to adjust the
value of the selected item (LCD Bright or LCDColour), then press the [OK] button.
■
You can set values for <LCD Bright> and
<LCD Colour> between <0> ~ <35>.
7. To exit, press the [MENU] button.
■
Adjusting the LCD Screen does not affect the
brightness and colour of the image to be recorded.