Samsung VC-U364B, VC-U366, VC-U364 User Manual

Vacuum

Cleaner

For Household

use Only

Operating

Instructions

Read these instructions before operating the vacuum cleaner

※The design and specification may be different depending on the models.

Safety Instructions

Thank you for purchasing a Samsung vacuum cleaner. When using an electrical appliance, basic precautions should always be followed, including the following:

PLEASE READ ALL WARNINGS AND INSTRUCTIONS BEFORE USING THIS APPLIANCE

Warning:

To reduce the risk of fire, electric shock, or injury:

·Do not leave appliance unattended when plugged in. Unplug the vacuum from the outlet

when it is not in use, or when it is being cleaned.

·Do not use outdoors or on wet surfaces.

·Do not allow to be used as a toy. Close attention is necessary when used by or near

children.

·Use only as described in this manual. Use only manufacturer’s recommended

attachments.

·Do not use with damaged cord or plug. If appliance is not working as it should, or has

been dropped, damaged, left outdoors or dropped in water, take it to a service center.

·Do not pull or carry the vacuum by the cord, or use the cord as a handle. Do not close a

door on cord, or pull the cord around sharp edges or corners. Do not run the appliance over its cord. Keep the cord away from heated surfaces.

·Do not unplug the vacuum by pulling on the cord. To unplug, grasp the plug, not the

cord.

·Do not handle plug or appliance with wet hands.

·Do not put any object into vacuum openings. Do not operate with any opening blocked:

Keep free of dust, lint, hair and anything that may reduce air flow.

·Keep hair, loose clothing, fingers and all parts of body away from openings and moving

parts.

·Do not use to pick up anything that is burning or smoking, such as cigarettes, matches

or hot ashes.

·Do not use without dust bag and filters in place.

·Turn off all controls before unplugging.

·Use extra care when cleaning on stairs.

·Do not use to clean up flammable or combustible liquids such as gasoline. Do not use

the vacuum in areas where such liquids may be present.

·Store your cleaner indoors in a cool, dry area.

·Do not use extension cords or plug into an electrical outlet with inadequate current

carrying capacity.

·Avoid vacuuming up sharp objects.

·Always turn this appliance off before connecting or disconnecting the hose, replacing

bags, or removing the bottom plate for maintenance.

·Unplug electrical appliances before vacuuming them.

Save these instructions!

To reduce the risk of electrical shock, this appliance has a polarized plug with one blade wider than the other. This plug will fit in a polarized outlet only one way. If the plug does not fit in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to replace the outlet. Do not change the plug in any way.

Assembling Parts

Assembled Vacuum Cleaner Parts

The assembled cleaner will look like the illustration to the left.

Hose Clip

Stretch Hose

Handle

Power Switch

Upper Tank Frame and Filter(Inside Louvers)

Upper Tank Post-Motor Filter

Hepa Media Filter (Optional Item)

Lock ’n Seal™ Lever

Handle Release Pedal

Furniture Protection Guard

Crevice Tool

Upper Tank Knob

Extension Wand

Quick Release Cord Wrap

Carrying Handle

Quick Reach Handle

Hose WandDusting Brush

Hose Wand Base

Louvers

Power Cord

Dirt Container

Pre-Motor Filter

Height

Adjustment

Knob

Powerfoot

WARNING!

OPERATE THE VACUUM CLEANER ONLY AT THE VOLTAGE SPECIFIED ON THE NAMEPLATE.

1. How to put it together.

Step 1. Attaching the Handle

1-1

Locate the vacuum Handle and remove the screw packet taped to the base of the Handle.

Stand the vacuum upright and slide the base of the handle firmly into the grooves at the top of the vacuum body.

1-2

Check to be sure the Handle is fitted to the vacuum body. If there is a gap in front, continue to push firmly until the Handle is flush. Insert one screw provided from the screw packet into the existing hole. Tighten securely with a Philliphs head screwdriver.

Step 2. Attaching the Hose and Tools

1-3

Position the Hose Assembly on the back of the vacuum as shown.

Attach the Hose with the remaining two screws from the packet. Tighten securely with a screwdriver.

1-4

Grasping the Quick Reach Handle, slide the end of the Hose Wand onto the Hose Wand Base. Snap the Hose into the Hose Clip.

NOTE: The Powerfoot will not operate effectively unless the Hose Wand is firmly attached.

1-5

Slide the Dusting Brush Tool into the storage clip as shown.

Slide the Extension Wand and the Crevice Tool together into the storage clip as shown.

+ 5 hidden pages