Samsung UW-28J10VD User Manual

3WAY COMBINATION TELEVISION
Owner’s Instructions
Before operating the unit,
please read this manual thoroughly,
and retain it for future reference.
REMOTE CONTROL
ON-SCREEN MENUS
TELETEXT FUNCTION
(depending on the model)
ENG

Safety Instructions

Do not expose the television to extreme temperature conditions or to extreme humidity conditions.
Do not expose the television to direct sunlight and other sources of heat.
Do not expose the television to any liquids.
Never put objects of any kind into the television, and do not place a water-containing vessel on the
television.
During a storm conditions (especially when there is lightning) unplug the television from the mains socket and aerial.
Do not step on or twist the power cord.
Do not overload wall outlets or extension cords as this can result in a risk of fire or electric shock.
Please use a soft and dry cloth (not containing volatile matter) when you clean the TV.
If the television is broken, do not try to repair it yourself. Contact qualified service personnel.
If the remote control is not used for a long period of time, remove the batteries and store it in a
cool, dry place.
Do not drop the remote control.
Displaying any stationary images that exceed the long time, it can cause uneven aging of
picture tubes (CRTs) that leave subtle, but permanent burned-in ghost images in the television picture. To avoid this, vary the programming and images, and primarily display full screen moving images, not stationary patterns or dark bars.
This device is not for use in industrial environments.
The product unit accompanying this user manual is licensed under certain intellectual property rights of certain third parties. This license is limited to private non-commercial use by end-user consumers for licensed contents. No rights are granted for commercial use. The license does not cover any product unit other than this product unit and the license does not extend to any unlicensed product unit or process conforming to ISO/IEC 11172-3 or ISO/IEC 13818-3 used or sold in combination with this product unit. The license only covers the use of this product unit to encode and/or decode audio files conforming to the ISO/IEC 11172-3 or ISO/IEC 13818-3. No rights are granted under this license for product features or functions that do not conform to the ISO/IEC 11172-3 or ISO/IEC 13818-3.
2

Caution

RISK OF ELECTRIC SHOCK
CAUTION
DO NOT OPEN
ENG
The lightning flash and arrow head within the triangle is a warning sign alerting you of “dangerous voltage” inside the product.
CAUTION: TO PREVENT ELECTRICAL SHOCK,
DO NOT REMOVE REAR COVER, NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
WARNING: TO PREVENT DAMAGE WHICH MAY RESULT
IN FIRE OR SHOCK HAZARD. DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
The exclamation point within the triangle is a warning sign alerting you of important instructions accompanying the product.
The main voltage is indicated on the
rear of the TV set and the frequency is 50 or 60Hz.
3
ENG

Contents (continued)

FOREWORD
Safety Instructions ......................................................................................... 2
Caution .......................................................................................................... 3
CONNECTING AND
View of Your Television ................................................................................. 6~7
Infrared Remote Control (Television and Teletext Functions) ....................... 8
Infrared Remote Control (VCR and DVD Functions)..................................... 9
Inserting the Batteries in the Remote Control................................................ 10
Connecting to an Aerial or Cable Television Network ................................... 10
Switching Your Television On and Off........................................................... 11
Placing Your Television in Standby Mode..................................................... 11
Automatic Degaussing to Remove Colour Patches....................................... 12
Becoming Familiar with the Remote Control ................................................. 13
Plug and Play Feature................................................................................... 14~15
Choosing Your Language.............................................................................. 15
PREPARING YOUR TELEVISION
SETTING THE CHANNELS
Storing Channels Automatically..................................................................... 16
Storing Channels Manually............................................................................ 17~18
Assigning Names to Channels ...................................................................... 19
Skipping Unwanted Channels ....................................................................... 20
Fine Tuning Channel Reception.................................................................... 21
Sorting the Stored Channels ......................................................................... 22
Activating the Child Lock ............................................................................... 23
Displaying Information ................................................................................... 24
USING
YOUR TELEVISION
Changing the Picture Standard ..................................................................... 24
Adjusting the Picture Settings........................................................................ 25
Selecting the Picture Size (depending on the model).................................... 26
Activating/Deactivating the Digital Noise Reduction Feature ........................ 27
Using the Tilt Control Feature........................................................................ 27
Viewing Pictures From External Sources ...................................................... 28
Setting the Blue Screen................................................................................. 28
Changing the Sound Standard ...................................................................... 29
Adjusting the Sound Settings ........................................................................ 29
Extra Sound Settings..................................................................................... 30
-
Auto Volume
-
Melody
-
Pseudo Stereo / Virtual Surround
-
Turbo Sound
Selecting the Sound Mode (depending on the model) .................................. 31
Setting the Current Date and Time................................................................ 32
Switching the Television On and Off Automatically ....................................... 33
Setting the Sleep Timer ................................................................................. 34
Locking the Front Panel................................................................................. 34
USING THE VCR FUNCTION (continued)
Cassette Types and Recording Speeds (Option).......................................... 35
Protecting a Recorded Cassette.................................................................... 35
Repeating Playback of a Sequence or Cassette........................................... 36
Symbols
Press Important Note
4

Contents

TM
USING THE VCR FUNCTION
Adjusting the Picture Contours ...................................................................... 37
Selecting the Type of Cassette Tape ............................................................ 37
Selecting the Video System (depending on the model)................................. 38
Selecting the HiFi Mode (depending on the model) ...................................... 39
Playing a Cassette......................................................................................... 40
Using the Tape Counter to Search for a Sequence....................................... 41
Using the Crystal PlayBack ........................................................................... 42
Adjusting the Picture Quality during Playback............................................... 42
Rewinding and Fast-forwarding a Cassette................................................... 43
Playing a Cassette in Slow Motion ................................................................ 44
Recording a Programme Directly (Option) .................................................... 45
Recording a Programme with Automatic Stop............................................... 46
Using the Feature (depending on the model) ............................... 47~48
Using the Feature (UK Only) ......................................................... 49~50
Setting the VCR Unit to Record a Programme Automatically........................ 51~52
USING THE DVD FUNCTION
Playing a Disc................................................................................................ 53~56
Using the Search and Skip Functions ........................................................... 57
Using the Disc Menu ..................................................................................... 58
Using the Title Menu...................................................................................... 58
Displaying the Disc Information ..................................................................... 59
Using the Zoom Function (DVD/VCD)........................................................... 60
Using the Bookmark Function (DVD/VCD).................................................... 61
Repeat Play................................................................................................... 62
Using the EZ View ......................................................................................... 63
Program Play................................................................................................. 64
Changing the Camera Angle ......................................................................... 64
Setting up the Language Features ................................................................ 65
Setting up the Audio Options......................................................................... 66
Setting up the TV Aspect............................................................................... 67
Setting up the Display Options ...................................................................... 68
Setting up the Parental Control ..................................................................... 69
ENG
USING THE
Teletext Feature ............................................................................................ 70
Displaying the Teletext Information ............................................................... 71
Selecting Display Options.............................................................................. 72
Selecting a Teletext Page.............................................................................. 73
Storing Teletext Pages .................................................................................. 74
TELETEXT FUNCTION
ADDITIONAL INFORMATION ON CONNECTIONS
Connecting to the External Input/Output ....................................................... 75
Connecting to the Digital Audio Outputs........................................................ 75
Connecting to the Audio/Video Input............................................................. 76
Connecting Headphones............................................................................... 76
RECOMMENDATIONS FOR USE
SCART Connector Wiring.............................................................................. 77
Cleaning the Video Heads............................................................................. 77
Disc Type and Characteristics....................................................................... 78
Technical Specifications ................................................................................ 79
Troubleshooting: Before Contacting Service Personnel................................ 80~81
Wiring the Mains Power Supply Plug (UK Only)............................................ 82
5
ENG

View of Your Television

Control Panels
The actual configuration on your TV may be different, depending on your model.
UW21J10VD UW28J10VD
Disc Tray
Load the disc here.
VCR Deck
Insert a standard VHS video tape.
Power
Press to turn the TV on and off.
UW17J11
Disc Tray
Load the disc here.
VCR Deck
Insert a standard VHS video tape.
Power
Press to turn the TV on and off.
6

View of Your Television (continued)

1
2
3
1
2
3
The actual configuration on your TV may be different, depending on
your model.
ENG
Control Panels (
Œ SKIP/SEARCH
Press to skip or search the title, chapter or track.
´ PLAY/PAUSE
Press to play or pause the disc
ˇ STOP
¨ OPEN/CLOSE
ˆ STAND BY
Ø TIMER
REC
Remote Control Sensor
(DVD)
Press to stop the disc.
Press to open and close the disc tray.
(indicator)
Lit when TV power is Off.
(indicator)
Lit when the program times are stored.
(indicator)
Lit when the VCR is recording.
Aim the remote control towards this spot on the TV.
continued)
(DVD)
(DVD)
(DVD)
Connection Panels
Side of the TV
REC
˝ STOP/EJECT
Ô REW / FF
PLAY/PAUSE
Ò – +
Ú C/P.
Æ MENU
(VCR)
Press to begin recording.
(VCR) Press to stop a video tape during play, record, rewind, or fast forward. Press to eject a video tape if the tape is stopped.
(VCR)
Press to rewind/fast forward a videotape.
(VCR)
Press to play or pause a video tape.
Press to increase or decrease the volume.
Press to change channels.
Press to display the on-screen menu.
Rear of the TV
UW21J10VD/UW28J10VD
Œ Digital Audio Outs
Audio Inputs (R, L)
Video Input
Headphone Connector
For further details about connection, refer to pages 75~76.
Whenever you connect an audio or video system to your television, ensure that all
elements are switched off.
Refer to the documentation supplied with your equipment for detailed connection instructions and associated safety precautions.
UW17J11
´ SCART Audio/
Video Input/Outputs
ˇ 75Ω Coaxial
Connector for Aerial/ Cable Network
7
ENG

Infrared Remote Control (Television and Teletext Functions)

POWER
DIRECT CHANNEL SELECTION
ONE/TWO-DIGIT CHANNEL
SOUND MODE SELECTION
TEMPORARY SOUND SWITCH-
VOLUME ADJUSTMENT
SOUND MODE SELECTION
SELECTION
OFF
TELETEXT INDEX
MENU DISPLAY
SWITCH BETWEEN THE TV/VCR AND DVD MODE
SWITCH REPEATEDLY BETWEEN THE LAST TWO CHANNELS DISPLAYED
TELETEXT DISPLAY
EXTERNAL INPUT SELECTION
CHANNEL SELECTION
TELETEXT NEXT PAGE
TELETEXT PREVIOUS PAGE
MIX BOTH TELETEXT INFORMATION AND THE NORMAL BROADCAST
PICTURE MODE SELECTION
ON-SCREEN DISPLAY
PICTURE SIZE SELECTION
MOVE TO THE REQUIRED
ADJUST AN OPTION VALUE
AUTOMATIC SWITCH-OFF
MENU OPTION/
RESPECTIVELY
TELETEXT STORE
TELETEXT SUB-PAGE
TELETEXT SIZE
TELETEXT REVEAL
Operation of remote control may be affected by bright artificial light near to the TV set.
8
CHANGE CONFIRMATION/ HIGHLIGHTED OPTION SELECTION
TELETEXT CANCEL
TELETEXT MODE SELECTION (LIST/FLOF)
TELETEXT HOLD

Infrared Remote Control (VCR and DVD Functions)

ENG
TAPE ALIGNMENT ADJUSTMENT
SEARCH BACKWARD
STOP
BACK SKIP THE TITLE, CHAPTER,
DVD MENU DISPLAY
OPEN/CLOSE THE DISC TRAY
ADVANCES PLAY ON FRAME AT
ACCESS VARIOUS CAMERA
VIDEOPLUS PRESET RECORDING
(The VIDEOPLUS printed in
SHOWVIEW on the Remote
Control Unit except UK
OR TRACK
A TIME
ANGLES ON A DVD
ZOOM
REPEAT PLAY
model.)
PLAY IN SLOW MOTION
SEARCH FORWARD
PLAY/PAUSE
NEXT SKIP THE TITLE, CHAPTER, OR TRACK
VCR: COUNTER, REMAIN DVD : DISPLAY
VCR RECORD/ RETURN TO PREVIOUS MENU
TO CANCEL OR CLEAR EACH SELECTED FUNCTION
CRYSTAL PLAYBACK (IPC)
DISPLAY SUBTITLES
VCR SPEED SELECTION (STANDARD PLAY/LONG PLAY)
9
ENG

Inserting the Batteries in the Remote Control

You must insert or replace the batteries in the remote control when you:
Purchase the television
Find that the remote control is no longer operating
correctly
1 Remove the cover on the rear of the remote control by pressing
the symbol ( ) downwards and then pulling firmly to remove it.
2 Insert two R03, UM4, “AAA” 1.5V or equivalent batteries taking
care to respect the polarities:
+
on the battery against +on the remote control
-
on the battery against -on the remote control
3 Replace the cover by aligning it with the base of the remote
control and pressing it back into place.
Rear of the TV

Connecting to an Aerial or Cable Television Network

To view television channels correctly, a signal must be received by the set from one of the following sources:
An outdoor aerial
A cable television network
A satellite network
1 In the first three cases, connect the aerial or network input cable to
the 75coaxial socket on the rear of the television.
or
Cable Television
Network
10
2 If you are using an indoor aerial, you may need to turn it when
tuning your television until you obtain a picture that is both sharp and clear. For further details, refer to:
“Storing Channels Automatically” on page 16
“Storing Channels Manually” on page 17

Switching Your Television On and Off

The mains lead is attached to the rear of your television.
If you have purchased this television in the United
Kingdom, refer to page 82 for further instructions on plug wiring.
1 Plug the mains lead into an appropriate socket.
The main voltage is indicated on the rear of the television
and the frequency is 50 or 60Hz.
2 Press the “ I ” button (On/Off) on the front of the television.
Result
: The Standby indicator on the front of the television
lights up.
3 Press the POWER () button on the remote control to switch the
television on.
Result
: The programme that you were watching last is re-
selected automatically.
If you have not yet stored any channels, No clear picture
appears. Refer to “Storing Channels Automatically” on page 16 or “Storing Channels Manually” on page 17.
ENG
Front of the TV
4 To switch your television off, press again the POWER () button
on the front of the television.

Placing Your Television in Standby Mode

Your television can be placed in Standby mode, in order to reduce the power consumption.
The Standby mode can be useful when you wish to interrupt viewing temporarily (during a meal, for example).
1 Press the POWER () button on the remote control.
Result
: The screen is turned off and the Standby indicator on
the front of the television lights up.
2 To switch the television back on, simply press again the POWER
() button on the remote control.
Do not leave your television in Standby mode for long
periods of time (when you are away on holiday, for example). Turn your television off by pressing the “ l ” button (On/Off) on the front of the television. It is best to unplug the set from the mains and aerial.
11
ENG

Automatic Degaussing to Remove Colour Patches

A degaussing coil is mounted around the picture tube so that external degaussing after moving the receiver is normally unnecessary. If the receiver is moved or placed in a different direction, or, a coloured patch appears on the screen, the main power switch must be switched to the off position for 120minutes or the power cord must be unplugged for the same interval to allow the automatic degauss circuits to operate properly.
For safety, the receiver should be switched off from the main power switch when it is unattended.
Magnetic fields can cause your television to malfunction. Degaussing is a process that
neutralises magnetic fields.
12

Becoming Familiar with the Remote Control

The remote control is used mainly to:
Change channels and adjust the volume
Set up the television using the on-screen menu system
The following table presents the most frequently used buttons and their functions.
Button Viewing Function Menu Function
ENG
Used to display the next stored channel.
Used to display the previous stored channel.
to Used to display the corresponding channels.
-/--
PRE-CH Used to switch repeatedly between the last two channels
MUTE Used to switch the sound off temporarily.
MENU Used to display the Used to return to the
Used to select a channel numbered ten or over. Press this button, and the “P Enter the two-digit channel number.
displayed.
Used to increase the volume.
Used to decrease the volume.
To turn the sound back on, press this button again,
or or button.
on-screen menu system. previous menu or normal
--
” symbol is displayed.
viewing.
-
-
-
-
-
-
Used to...
Display a submenu containing selections for the current menu option.
Increase/reduce a menu option value.
Used to confirm your choice.
13
ENG

Plug and Play Feature

Plug & Play
Language
English Español
Deutsch Português Français Italiano Nederland Sverige
Adjust Select
Ant. Input : Check
When the television is initially powered on, several basic customer settings proceed automatically and subsequently. The following settings are available.
1 If the television is in Standby mode, press the POWER () button
on the remote control.
Result
: The Plug & Play is displayed.
2 To start the Plug & Play, press the ENTER button.
Result
: The Language menu is displayed.
3 Select the appropriate language by pressing the or button.
Press the MENU () button to confirm your choice.
Result
: The message Antenna input check is displayed.
Exit
Channel
Auto Store
Country : Belgie
Search : 435.250MHz
Select Adjust Exit
Channel
Auto Store
Country : Belgie
Search : 435.250MHz
Select Adjust Exit
P 1 C
-- -----
67.250 MHz 78 3 %
4 Make sure that the antenna is connected to the TV.
Result
: After a little while, the Country menu is displayed.
5 Select your country by pressing the or button. Press the
MENU () button to confirm your choice.
Result
: The Auto Store menu is displayed.
6 To start the channel store, press the ENTER button.
Result
: The search will end automatically. Channels are sorted
and stored in an order which reflects their position in the frequency range (with lowest first and hialghest last).
To stop the search before it has finished or return to normal
viewing, select the Exit and press the ENTER button
.
7 When searching and storing is complete, the Time menu is
displayed.
8 Press the œ or button to move to the hour or minute. Set the
hour or minute by pressing the ▲ or ▼ button (refer to “Setting the Current Date and Time” on page 32).
9 When the setting has finished all, the message Enjoy viewing
your new TV is displayed, and then the channel which has been
stored will be activated.
Exit
Time
Clock - - : - -
Move Exit
ENJOY YOUR WATCHING
14

Plug and Play Feature (continued)

If you want to reset this feature...
1 Press the MENU button.
Result
: The main menu is displayed.
2 Press the or button to select Function.
Result
: The options available in the Function group are
displayed.
3 Press the œ or button.
4 Press the or button to select Plug & Play.
5 Press the œ or button.
Result
: This feature starts with the message Plug & Play is
displayed.
Function
TV/AV : TV Language : English Time
Plug & Play
Blue Screen : Off Panel Lock : Off
Select Enter Exit
ENG

Choosing Your Language

When you start using your television for the first time, you must select the language which will be used for displaying menus and indications.
1 Press the MENU button.
Result
: The main menu is displayed.
2 Press the or button to select Function.
Result
: The options available in the Function group are
displayed.
3 Press the œ or button.
Result
: The Language is selected.
4 Select the appropriate language by pressing the œ or button
repeatedly.
Function
TV/AV : TV
Language : English
Time Plug & Play Blue Screen : Off Panel Lock : Off
Select Adjust Exit
15
ENG

Storing Channels Automatically

Channel
Auto Store
Manual Store Name Add/Erase Fine Tune Sort Child Lock
Select Enter Exit
Channel
Auto Store
Country : Belgie
Search : 435.250MHz
Select Adjust Exit
Channel
Auto Store
Country : Belgie
Search : 435.250MHz
You can scan for the frequency ranges available to you (and availability depends on your country). Automatically allocated programme numbers may not correspond to actual or desired programme numbers. However you can sort numbers manually and clear any channels you do not wish to watch.
1 Press the MENU button.
: The main menu is displayed.
Result
2 Press the or button to select Channel.
: The options available in the Channel group are
Result
displayed.
3 Press the œ or button.
: The Auto Store is selected.
Result
4 Press the œ or button again.
: The Auto Store menu is displayed with the
Result
Country is selected.
5 Select your country by pressing the œ or button.
The countries are displayed in the following order:
Belgie
-
Deutschland-España-France-Italia
-
Nederland-Sverige-Schweiz-UK-Others.
If you have selected the Others option but do not wish to
scan the PAL frequency range, store the channels manually (see page 17).
Select Adjust Exit
P 1 C
-- -----
67.250 MHz 78 3 %
Exit
6 Press the or button to select Search.
7 Press the œ or button to start the search.
: The channels are stored in an order which reflects
Result
their positions in the frequency range. Finally, the search will end automatically.
To stop the search before it has finished or return to normal
viewing, press the MENU button.
8 When the channels have been stored, you can:
Assign a name to the stored channels (refer to page 19)
Clear a channel (refer to page 20)
Fine tune channel reception if necessary (refer to page 21)
Sort them in the order required (refer to page 22)
16

Storing Channels Manually

You can store the television channels, including those received via cable networks.
When storing channels manually, you can choose:
Whether or not to store each of the channels found
The programme number of each stored channel which
you wish to identify
1 Press the MENU button.
Result
: The main menu is displayed.
2 Press the or button to select Channel.
Result
: The options available in the Channel group are
displayed.
3 Press the œ or button.
Channel
Auto Store
Manual Store
Name Add/Erase Fine Tune Sort Child Lock
Select Enter Exit
Channel
Manual Store Color System : AUTO
Sound System : B/G Search : 435.250MHz Channel : C 2 Prog. No. : P 1 Store : ?
-----
ENG
4 Press the or button to select Manual Store. Press the œ or
button.
Result
: The Manual Store menu is displayed with the Color
System is selected.
5 If necessary, select the broadcasting standard required by
pressing the œ or button repeatedly.
Result
: The color standards are displayed in the following
order (depending on the model).
AUTO
-
PAL-SECAM
AUTO-PAL-SECAM-NTSC4.43-NTSC3.58
-
NTSC4.43
6 Press the † or button to select Sound System. Press the œ or
button repeatedly.
Result
: The sound standards are displayed in the following
order (depending on the model).
B/G-I -D/K-L/L’
B/G-I -D/K-M
Select Adjust Exit
Channel
Manual Store
Color System : AUTO
Sound System : B/G
Search : 435.250MHz Channel : C 2 Prog. No. : P 1 Store : ?
Select Adjust Exit
-----
17
ENG

Storing Channels Manually (continued)

Channel
Manual Store
Color System : AUTO Sound System : B/G Search : 435.250MHz
Channel : C 2
Prog. No. : P 1 Store : ?
Adjust Move Exit
Manual Store
Color System : AUTO Sound System : B/G
Search : 435.250MHz
Channel : C 2 Prog. No. : P 1 Store : ?
Select Adjust Exit
Manual Store
Color System : AUTO Sound System : B/G Search : 435.250MHz Channel : C 2
Prog. No. : P 1
Store : ?
Select Adjust Exit
-----
Channel
-----
Channel
-----
7 If you know the number of the channel to be stored, see the
following steps.
Press the or button to select Channel.
Press the button.
Press the or button to select C (Air channel) or S (Cable channel).
Press the button.
Press the or button to select the required number.
If no sound or abnormal sound, re-select the sound
standard required.
8 If you do not know the channel numbers, select Search by
pressing the or button. Press the œ or button to start the search.
Result
: The tuner scans the frequency range until the first
channel or the channel that you selected is received on your screen.
9 To assign a programme number to a channel, select Prog.No. by
pressing the or button. Press the œ or button to find the correct number.
10 To store the channel and associated programme number, select
Store by pressing the † or button. Set to OK by pressing the œ or button.
11 Repeat Steps 7 to 10 for each channel to be stored.
Channel
Manual Store
Color System : AUTO Sound System : B/G Search : 435.250MHz Channel : C 2 Prog. No. : P 1
Store : OK
Select Adjust Exit
18
-----
Channel mode
P (Programme mode):
broadcasting stations in your area have been assigned to position numbers from P00 to max P99. You can select a channel by entering the position number in this mode.
C (Real channel mode):
entering the assigned number to each air broadcasting station in this mode.
S (Cable channel mode):
entering the assigned number for each cable channel in this mode.
When completing tuning, the
You can select a channel by
You can select a channel by

Assigning Names to Channels

Channel names will be assigned automatically when channel information is broadcast. These names can be changed, allowing you to assign new names.
1 Press the MENU button.
Result
: The main menu is displayed.
2 Press the or button to select Channel.
Result
: The options available in the Channel group are
displayed.
Channel
Auto Store Manual Store
Name
Add/Erase Fine Tune Sort Child Lock
Select Enter Exit
ENG
3 Press the œ or button.
4 Press the or button to select Name. Press the œ or button.
Result
: The current channels are displayed.
5 If necessary, select the channel to be assigned to a new name by
pressing the or button.
6 Move on the previous or next letter by pressing the œ or button.
Press the or button to select a letter (A~Z), a number (0~9) or a symbol (
-, _
, space).
7 Repeat Steps 5 to 6 for each channel to be assigned to a new
name.
Channel
Name
P 1 :
-----
P 2 :
-----
P 3 :
-----
P 4 :
-----
Select Adjust Exit
Channel
Name
P 1 :
-----
P 2 :
-----
P 3 :
-----
P 4 :
-----
Adjust Move Exit
19
ENG

Skipping Unwanted Channels

Channel
Auto Store Manual Store Name
Add/Erase
Fine Tune Sort Child Lock
Select Enter Exit
Channel
Add/Erase
P 1 : Added
P 2 : Added P 3 : Added P 4 : Added
Select Adjust Exit
Channel
Add/Erase
P 1 : Erased
P 2 : Added P 3 : Added P 4 : Added
You can exclude the channels of your choice from the channel scan operation. When you scan through the stored channels, those that you have chosen to skip are thus not displayed. All channels that you do not specifically choose to skip are displayed during scanning.
1 Press the MENU button.
Result
: The main menu is displayed.
2 Press the or button to select Channel.
Result
: The options available in the Channel group are
displayed.
3 Press the œ or button.
4 Press the or button to select Add/Erase. Press the œ or
button.
Result
: The current channels are displayed.
5 Press the or button to select the channel to add or erase.
Select Erased or Added by pressing the œ or button.
6 Repeat Step 5 for each channel to be added or erased.
Select Adjust Exit
20

Fine Tuning Channel Reception

If the reception is clear, you do not have to fine tune the channel, as this is done automatically during the search and store operation. If the signal is weak or distorted, you may have to fine tune the channel manually.
1 Press the MENU button.
Result
: The main menu is displayed.
Channel
Auto Store Manual Store Name Add/Erase
Fine Tune
Sort Child Lock
ENG
2 Press the or button to select Channel.
Result
: The options available in the Channel group are
displayed.
3 Press the œ or button.
4 Press the or button to select Fine Tune. Press the œ or
button.
Result
: The Fine Tune menu is displayed with the Tune is
selected.
5 To obtain a sharp and clear picture and good sound quality, press
the œ or button.
Result
: The horizontal bar is displayed. Move the horizontal
bar’s cursor left or right by pressing the œ or button.
6 To memorise adjusted picture or sound, select Store by pressing
the or button. Press the œ or button.
Result
: OK is displayed.
7 To erase adjusted picture or sound, select Erase by pressing the
or button. Press the œ or button.
Result
: OK is displayed.
Select Enter Exit
Channel
Fine Tune
Tune : 99.315MHz
Store : ? Erase : ?
Select Adjust Exit
Fine Tune 99.315MHz
Channel
Fine Tune
Tune : 99.315MHz
Store : OK
Erase : ?
Select Adjust Exit
Channel
Fine Tune
Tune : 99.315MHz Store : ?
Erase : OK
Select Adjust Exit
21
ENG

Sorting the Stored Channels

Channel
Auto Store Manual Store Name Add/Erase Fine Tune
Sort
Child Lock
Select Enter Exit
This operation allows you to change the programme numbers of stored channels. This operation may be necessary after using auto store. You can delete the channels you do not want to keep.
1 Press the MENU button.
Result
: The main menu is displayed.
2 Press the or button to select Channel.
Result
: The options available in the Channel group are
displayed.
Channel
Sort
From : P 1
To : P Store : ?
Select Adjust Exit
Sort
From : P 1
To : P 3
Store : ?
Select Adjust Exit
Sort
From : P 3 To : P 1
Store : OK
-----
-- -----
Channel
-----
-----
Channel
-----
-----
3 Press the œ or button.
4 Press the or button to select Sort. Press the œ or button.
Result
: The Sort menu is displayed with the From is
selected.
5 Select the channel number that you wish to change by pressing
the œ or button repeatedly.
6 Press the or button to select To. Select the new channel
number which you wish to identify by pressing the œ or button repeatedly.
7 Press the or button to select Store. Select OK to confirm the
exchange of channel numbers by pressing the œ or button.
:
Result
The selected channel is exchanged with the one previously stored to the chosen number.
8 For all the channels to move to the required channel numbers,
repeat steps 5 to 7 after selecting the From by pressing the orbutton.
Select Adjust Exit
22

Activating the Child Lock

This feature allows you to lock individual channals so that they cannot be selected from the front panel or the remote. It can, however, still be switched on via the remote control. Thus, by keeping the remote control away from unauthorised users, such as children, you can prevent them from watching unsuitable programme.
1 Press the MENU button.
Result
: The main menu is displayed.
2 Press the or button to select Channel.
Result
: The options available in the Channel group are
displayed.
3 Press the œ or button.
4 Press the or button to select Child Lock. Press the œ or
button.
5 To activate this feature, select On by pressing the œ or button.
Channel
Auto Store Manual Store Name Add/Erase Fine Tune Sort
Child Lock
Select Enter Exit
Channel
Child Lock
Child Lock : On
Prog. No. : 1 Lock : ?
Select Adjust Exit
ENG
6 Press the or button to select Prog.No.. Select the number of
the programme to which the channel is to be locked by pressing the œ or button.
7 Press the or button to select Lock. Select Locked by
pressing the œ or button.
Channel
Child Lock
Child Lock : On
Prog. No. : 1
Lock : ?
Select Adjust Exit
Channel
Child Lock
Child Lock : On Prog. No. : 1
Lock : Locked
Select Adjust Exit
P 1
Child Lock : Locked
23
ENG

Displaying Information

You can display various types of information on the screen to help you use your television.
Press the INFO button to display the information. To remove the information from the screen, press the INFO button again.
When a cassette is present in the VCR or DVD, even if it is
stopped, the same information is displayed in television mode as in the VCR or DVD mode.

Changing the Picture Standard

Picture
Mode
Adjust Color Tone : Normal Size : Wide Digital NR : Off
Select Adjust Exit
œœ
Dynamic
You can select the type of picture which best corresponds to your viewing requirements.
1 Press the MENU button.
Result
:
The options available in the displayed.
Picture
group are
2 Press the œ or button.
Result
:
The
Mode
is selected.
3 Select the required picture effect by pressing the œ or button
repeatedly.
Result
: The following picture effects are available:
Dynamic
You can also set these options simply by pressing the
P.MODE (Picture Mode) button.
-
Standard-Movie-Custom.
24

Adjusting the Picture Settings

Your television has several settings which allow you to control picture quality.
1 Press the MENU button.
:
Result
The options available in the displayed.
2 Press the œ or button.
3 Press the or button to select Adjust. Press the œ or
button.
Result
: The Adjust menu is displayed.
4 Press the or button to select the option to be adjusted
(Contrast, Brightness, Sharpness, Color , or Tint-NTSC only). Press the œ or button.
Result
: The horizontal bar is displayed. Move the horizontal
bar’s cursor left or right by pressing the œ or button.
5 Press the MENU button.
:
Result
The options available in the displayed again.
Picture
Picture
group are
group are
Picture
Mode
Adjust
Color Tone : Normal Size : Wide Digital NR : Off
Select Enter Exit
Adjust
Contrast 100
Brightness 50 Sharpness 60 Color 50
Select Adjust Exit
Contrast 100
œœ
Dynamic
Picture
ENG
6 Press the or button to select Color Tone. Press the œ or
button repeatedly.
Result
: The color tones are displayed in the following order.
Normal
-
Warm 1-Warm 2
If you make any changes to these settings, the picture
mode is automatically switched to Custom.
-
Cool 2-Cool 1
Picture
Mode Adjust
Color Tone : Normal
Size : Wide Digital NR : Off
Select Adjust Exit
œœ
Dynamic
25
ENG

Selecting the Picture Size (depending on the model)

Picture
Mode Adjust Color Tone : Normal
Size : Wide
Digital NR : Off
Select Adjust Exit
œœ
Dynamic
You can select the picture size which best corresponds to your viewing requirements.
1 Press the MENU button.
Result
: The options available in the Picture group are
displayed.
2 Press the œ or button.
3 Press the or button to select Size. Press the œ or button
repeatedly.
Result
: The picture sizes are displayed in the following order
(depending on the model).
Wide-Panorama-Zoom1-Zoom2-4:3
Normal-Zoom
You can select these options by simply pressing the P.SIZE
button on the remote control.
26
Loading...
+ 58 hidden pages