The product color and shape may vary depending on the
➢
model.
Rear JackSide Jack
Owner’s Instructions
Before operating, please read this manual thoroughly,
Register your product at www.samsung.com/global/register.
and retain it for future reference.
Record your Model and Serial number.
▪ Model __________ ▪ Serial No. __________
Control Panel(depending on the model)
The product color and shape may vary depending on the
➢
model.
Front Panel
1 On-screen menu display
2 Volume adjustment
3 Channel selection
4 Remote control sensor
5 Indicator (Standby or Timer)
6 Power on/off
The 2 and 3 buttons also have the same function as the
◄/►/▲/▼ buttons on the remote control.
If the remote control no longer works or you have
misplaced it, you can use the controls on the panel of the
television.
1
2
Whenever you connect an audio or video system to your
➢
television, ensure that all elements are switched off.
Please be sure to match the color coded input terminals
and cable jacks.
1 Audio/Video Output Jacks
Connect to the audio/video input jacks of a recording VCR.
2 Audio/Video Input Jacks
Connect to the audio/video output jacks of VCRs, DVD players
and similar devices.
3 Component Video Input Jacks (Y, PB, PR)
Connect to the Component video outputs of a DVD or DTV
set-top box. 480i video signal input is available.
When using the Component Video input, connect audio jacks
to “AV IN 2 (AUDIO-L/R)”.
4 VHF/UHF
Connect to an antenna or to a cable TV system.
3
3
4
1 Audio input
2 Video input
3 Headphone jack
Please be sure to match the color coded input terminals
➢
and cable jacks.
When both the side and rear jacks (AV IN 2) are
connected to external equipment, the side receives
priority.
1 Audio Input Jacks
Connect audio signals from a camcorder or video game.
2 Video Input Jack
Connect a video signal from a camcorder or video game.
3 Headphone Jack
Connect a set of external headphones to this jack for private
listening.
English - 1
AA68-03905M-00
Remote Control (depending on the model)
Turning the TV On and Off
Operation of remote control may be affected by bright
➢
artificial light near to the TV.
This is a special remote control for the visually impaired,
➢
and has Braille points on the POWER, Channel and
Volume buttons.
1POWER
Turns the TV on and off.
2Number buttons
Press to select channels
directly on the TV.
3 –
Press to select channels
over 100. For example,
for channel 122, press
“-”, then “2”, then “2”.
4VOL +, VOL -
Press to increase or
decrease the volume.
5MENU
Displays the main
on-screen menu.
6 ▲/▼/◄/►
Controls the cursor in
the menu.
7ENTER
While using the
onscreen menus, press
ENTER to activate (or
change) a particular
item.
8MTS
(Multi-channel Television
Sound)
Press to choose
“Stereo”, “Mono”, or
“SAP” (Secondary Audio
Program).
9R.SURF
Press to automatically
return to a preferred
channel after a
userpreset time delay.
0SOURCE
Press to display all
of the available video
sources.
! INFO
Press to display
information on the TV
screen.
@PRE-CH
Tunes to the previous
channel.
#CH , CH
Press to change
channels.
$EXIT
Press to exit the menu.
%MUTE
Press to temporarily cut
off the sound.
^SLEEP
Press to select a
preset time interval for
automatic shut off.
Press the POWER button on the remote control.
You can also use the POWER button on the TV.
Viewing the Menus
1 Press the MENU button.
The main menu is displayed on the screen. Its left side
has five icons: “Input”, “Picture”, “Sound”, “Channel”, and
“Setup”.
2 Press the ▲ or ▼ button to select one of the icons.
Press the ENTER button to access the icon’s sub-menu.
3 Press the ▲ or ▼ button to move to items in the menu.
Press the ENTER button to enter items in the menu.
4 Press the ▲/▼/◄/► button to change the selected items.
Press the MENU button to return to the previous menu.
5 Press the EXIT button to exit from the menu.
Installing Batteries
Remove the cover. Install two AAA size
batteries, then replace the cover.
When the remote control does not operate
normally, check that the “+” and “–” ends of
the batteries are inserted correctly or the
batteries are drained.
Do not mix battery types, i.e. alkaline and manganese.
➢
English - 2
English - 3
Setup - Plug & Play
Channel - Memorizing the Channels
When the TV is initially powered on, several basic customer
settings proceed automatically and subsequently.
The following settings are available.
1 Press the POWER button on
the remote control.
The “Start Plug & Play” is
displayed. Press the ENTER
button, then the “Language”
is displayed.
2 Press the ▲ or ▼ button to
select the desired language,
then press the ENTER
button. The “Check antenna
input.” is displayed.
Plug & Play
Start Plug & Play
OK
Enter Return
Plug & Play
Language
English
Español
Português
Français
Move Enter Skip
3 Make sure that the antenna
is connected to the TV.
Press the ENTER button,
then the “Auto Program” is
displayed.
4 Press the ENTER button
to start. The TV begins
memorizing all available
channels. Press the ENTER
button to stop.
Plug & Play
Check antenna input.
OK
Enter Skip
Plug & Play
Auto Program
Air 3
Stop
Enter Skip
3%
5 After all available channels
are stored, the “Clock Set” is
displayed.
Press the ◄ or ► button to
move to the hour or minute.
Set the clock by pressing the
Plug & Play
Clock Set -- : -- am
Move Enter
Skip
▲ or ▼ button.
6 When you have finished,
press the MENU button.
The “Enjoy your watching.” is
displayed.
Plug & Play feature
➢
doesn’t work in the AV
Enjoy your watching.
mode.
Re-setting the Plug & Play
Method:
MENU ▲/▼ (Setup)
ENTER ▲/▼ (Plug & Play)
ENTER
Plug & Play ►
Language : English ►
Time ►
Caption ►
V-Chip ►
Blue Screen : Off ►
Melody : On ►
Demonstration ►
Move Enter Return
Input - Source List / Edit Name
Source List
You can switch between
viewing signal from
connected equipment, such
as a VCR, DVD, set-top
box, and the TV source
(broadcast or cable).
Press the SOURCE button on the remote control
➢
repeatedly to select the desired signal source.
Edit Name
You can give a name to the
external source.
TV
AV1
AV2
Component
Move Enter Return
AV1 : -- --
AV2 : ----
Component : ----
Move Enter Return
OK
Setup
Source List
-- --
-- --
-- --
Edit Name
-- --
VCR
DVD
Cable STB
Sat. STB
AV Receiver
DVD Receiver
▼
Your TV can memorize and store all of the available channels
for both air and cable channels. After the available channels
are memorized, use the CH and CH buttons to scan
through the channels.
This eliminates the need to change channels by entering the
channel digits. There are three steps for memorizing channels:
“Air/Cable”, “Auto Program” and “Add/Delete”.
Air/Cable
Before your TV can begin
memorizing the available
channels, you must specify
the type of signal source
that is connected to the TV
(i.e., an antenna or a cable
Air/Cable :Air
Auto Program
Add/Delete
Fine Tune
Name
Move Enter Return
Air
STD
HRC
IRC
Channel
system).
Select “Air”, “STD”, “HRC”, or “IRC” by pressing the ▲ or
▼ button.
Auto Program
All available channels are
automatically stored in
memory when channels are
selected by the direct tuning
function.
Press the ENTER button
Air 3
Search
Stop
Enter Return
3%
at any time to interrupt the
memorization process.
Deleted
Added
Add/Delete
Add/Delete
You can add or delete
a channel to display the
channels you want only.
To use the “Add/Delete”
function, first run Auto
Program.
▲ More
2 : Deleted
3 :Deleted
4 : Deleted
5 : Deleted
6 : Deleted
▼ More
Move Enter Return
Select “Deleted” or “Added”
by pressing the ▲ or ▼
button.
continued...
Loading...
+ 5 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.