Samsung TX-S3079WH, TX S2783, TX S3080WH User Manual
TX-S3079WH
TX-S3080WH
COLOR TELEVISION
Owner’s
Instructions
Register your product at www.samsung.com/global/register
Important Warranty Information Regarding Television Format Viewing
Standard screen format televisions (4:3, the aspect ratio of the screen width to height) are primarily designed to
view standard format full-motion video. The images displayed on them should primarily be in the standard 4:3
ratio format and constantly moving. Displaying stationary graphics and images on screen, such as the dark top
and bottom letterbox bars (wide screen pictures), should be limited to no more than 15% of the total television
viewing per week.
Wide screen format televisions (16:9, the aspect ratio of the screen width to height) are primarily designed to
view wide screen format full-motion video. The images displayed on them should primarily be in the wide
screen 16:9 ratio format, or expanded to fill the screen if your model offers this feature, and constantly moving.
Displaying stationary graphics and images on screen, such as the dark side-bars on non-expanded standard
format television video and programming, should be limited to no more than 15% of the total television
viewing per week.
Additionally, viewing other stationary images and text such as stock market reports, video game displays,
station logos, web sites or computer graphics and patterns, should be limited as described above for all
televisions.
picture tubes (CRTs) that leave subtle, but permanent burned-in ghost images in the television picture. To
avoid this, vary the programming and images, and primarily display full screen moving images, not
stationary patterns or dark bars. On television models that offer picture sizing features, use these controls to
view the different formats as a full screen picture.
Displaying any stationary images that exceed the above guidelines can cause uneven aging of
Be careful in the selection and duration of television formats used for viewing. Uneven CRT aging as a result
of format selection and use, as well as other burned-in images, is not covered by your Samsung limited
warranty.
English-2
Contents
GENERAL INFORMATION
List of Features .................................................................................. 4
Accessories........................................................................................ 4
Viewing the Control Panel.................................................................. 5
Viewing the Connection Panel........................................................... 6
Remote Control.................................................................................. 7
Installing Batteries in the Remote Control ......................................... 8
CONNECTIONS
Connecting VHF and UHF Antennas................................................. 8
Connecting Cable TV......................................................................... 9
Connecting a VCR ............................................................................. 10
Connecting an S-VHS VCR ............................................................... 10
Connecting a Second VCR to Record from the TV ........................... 11
Connecting a Camcorder ................................................................... 11
Connecting a DVD Player/Set-Top Box............................................. 11
Connecting a DVD Player/Set-Top Box via HDMI
Connecting a Digital Audio System.................................................... 12
Connecting an Amplifier/DVD Home Theater .................................... 13
OPERATION
Turning the TV On and Off................................................................. 13
Plug & Play Feature........................................................................... 13
Changing Channels ........................................................................... 15
Adjusting the Volume ......................................................................... 16
Viewing the Display............................................................................ 16
Viewing the Menus............................................................................. 16
Memorizing the Channels .................................................................. 17
Setting Up Your Remote Control........................................................ 18
To Select the Source.......................................................................... 23
To Edit the Input Source Name ......................................................... 23
......................................... 12
CHANNEL CONTROL
Selecting the Antenna................................................................... 30
Adding and Erasing Channels...................................................... 30
To set-up Your Favorite Channels ................................................ 31
Viewing the Channel Lists ............................................................ 32
Setting the Default Channel List Mode......................................... 32
Labeling Channels........................................................................ 33
Fine Tuning Analog Channels....................................................... 33
Checking the Digital-Signal Strength............................................ 34
Using the R.Surf Feature.............................................................. 34
TIME SETTING
Setting the Time............................................................................ 35
FUNCTION DESCRIPTION
Selecting a Menu Language......................................................... 38
Using the V-Chip........................................................................... 38
Viewing Closed Captions(On-Screen Text Messages) - Digital ... 45
Viewing Closed Captions(On-Screen Text Messages) - Analog .. 46
Menu Transparency Level ............................................................ 47
Setting the Blue Screen Mode...................................................... 47
Setting the Function Help ............................................................. 47
APPENDIX
Identifying Problems .................................................................... 48
Specifications................................................................................ 48
PICTURE CONTROL
Using Automatic Picture Settings....................................................... 24
Changing the Screen Size ................................................................. 25
Tilt....................................................................................................... 26
Setting the Film Mode........................................................................ 26
SOUND CONTROL
Using Automatic Sound Settings.................................................. 26
Customizing the Sound ................................................................ 27
Setting the SRS TruSurround XT ................................................. 27
Automatic Volume Control............................................................ 28
Choosing a Multi-Channel Sound (MTS) track - Digital ............... 28
Choosing a Multi-Channel Sound (MTS) track - Analog .............. 29
Setting the On/Off Melody ............................................................ 29
Symbol Press Important Note One-Touch
☛
➢
Button
English-3
General Information
List of Features
s
Adjustable picture settings that can be stored in the TV’s memory.
s
Automatic timer to turn the TV on and off.
s
A special sleep timer.
s
V-Chip function.
s
Excellent Digital Interface & Networking:
With a built-in HD digital tuner, non-subscription HD broadcasts can be viewed with no Set-Top Box needed.
s
Remote Control
The supplied remote can be used to operate the TV as well as most DVD players, Set-top boxes, Cable Boxes and VCRs.
s
Excellent Picture Quality
- DNIe technology provides life-like clear images.
s
SRS TruSurround XT
- SRS TruSurround XT provides a virtual Dolby surround system.
Accessories
Please make sure the following items are included with your TV.
If any items are missing, contact your dealer.
Remote Control (AA59-00381A)/
AAA Batteries
The following parts are sold separately and are available at most electronics stores.
S-VIDEO Cable Video Cable Audio Cable Component Cable
Optical Cable Antenna Cable HDMI Cable HDMI/DVI Cable
Owner’s Instructions/
Safety Guide Manual
English-4
Warranty Cards/Registration Card
(Not available in all locations)
Viewing the Control Panel
Buttons on the Lower-Right Part of the Panel
The buttons on the lower-right panel control your TV’s basic features, including the on-screen menu.
To use the more advanced features, you must use the remote control. The product color and shape may very depending on the model.
TX-S3079WH
TX-S3080WH
1 SOURCE
Toggles between all the available input sources
(TV, AV1, AV2, S-Video, Component1, Component2,
HDMI or HDMI1,2(depending on the model)).
In the on-screen menu, use this button as you would
use the ENTER button on the remote control.
2 MENU
Press to see an on-screen menu of your TV’s
features.
3 + VOL –
Press to increase or decrease the volume.
In the on-screen menu, use the + VOL – buttons as
you would use the ˇ and ˆ buttons on the remote
control.
4 CH
Press to change channels.
In the on-screen menu, use the CH buttons as
you would use the and buttons on the remote
control.
5 Power Indicator
Blinks and turns off when the power is on and lights
up in stand-by mode.
6 Remote Control Sensor
Aim the remote control towards this spot on the TV.
7 POWER
Press to turn the TV on and off
English-5
Viewing the Connection Panel
Rear Panel Jacks
Use the rear panel jacks to connect A/V components that will be connected continuously, such as VCR or DVD players.
For more information on connecting equipment, see pages 8~13. The product color and shape may very depending on the model.
TX-S3079WH
1 AV IN 1
Video and audio inputs for external devices, such as
a camcorder or VCR.
2 AV OUT
Connect to the audio/video input jacks of a recording
VCR.
3 COMPONENT IN 1,2
Connect Component video/audio.
4 UPGRADE PORT (USB)
For service only.
TX-S3080WH
5 DIGITAL AUDIO OUT (OPTICAL)
Connect to a Digital Audio component.
6 HDMI IN(TX-S3079WH)
HDMI 1, 2 IN(
Connect to the HDMI jack of a device with an HDMI
output.
7 ANT 1 IN(AIR) / ANT 2 IN(CABLE)
Connect to an antenna (air) or cable TV system.
TX-S3080WH
)
Side Panel Jacks
Use the left side panel jacks to connect a component that is used only occasionally, such as a camcorder or video game. (See page 11)
The product color and shape may very depending on the model.
1 S-VIDEO IN
S-Video input for external devices with an S-Video output.
2 AV IN 2
Video and audio inputs for external devices, such as a camcorder or
VCR.
English-6
Remote Control
You can use the remote control up to a distance of about 23 feet from the TV. When using the remote control, always point it directly at
the TV. You can also use your remote control to operate your VCR, Cable box, DVD player, or Set-Top Box.
1 POWER
Turns the TV on and off.
2 NUMERIC BUTTONS
Press to change the channel.
3 –
Press to select additional
channels (digital and analog)
being broadcast by the same
station. For example, to select
channel “54-3”, press “54”, then
press “–” and “3”.
4 CH MGR
Used to display Channel Lists on
the screen.
5 ANTENNA
Press to select “AIR” or “CABLE”.
6 VCR/DVD Functions
- Rewind
- Stop
- Play/Pause
- Fast/Forward
7 MUTE
Press to temporarily cut off the
sound.
8 + VOL –
Press to increase or decrease the
volume.
9 MENU
Displays the main on-screen
menu.
0 UP/DOWN/LEFTˇ/
RIGHTˆ/ENTER
Use to select on-screen menu
items and change menu values.
! CAPTION
Controls the caption decoder.
@ P.MODE
Press to select the picture mode.
# S.MODE
Press to select the sound mode.
$ AUTO PROG.
Press to automatically store
selected Air/Cable channels.
% ADD/DEL
Use to store and delete channels
to/from memory.
^ SET
Sets the remote to control your
TV, VCR, Cable, DVD, or Set-Top
Box.
& TV, DVD, STB, CABLE, VCR
Press to operate your TV, DVD,
STB, CABLE (box), or VCR.
* SOURCE
Press to display all of the
available video sources.
( PRE-CH
Tunes to the previous channel.
) FAV.CH
Press to switch to your favorite
channels.
a SLEEP
Press to select a preset time
interval for automatic shut off.
b CH
Press to change channels.
c EXIT
Press to exit the menu.
d INFO
Press to display information on
the TV screen.
e R.SURF
Press to automatically return to a
preferred channel after a userpreset time delay.
f Color buttons
Press to add or delete channels
and to store channels to the
favorite channel list in the
“Channel Manager” menu.
g S.STRENGTH
Press to check the digital signal
strength.
h P.SIZE
Press to change the screen size.
i SRS
Selects SRS TruSurround XT
mode.
j MTS
Press to choose stereo, mono or
Separate Audio Program(SAP
broadcast).
k RESET
When your remote control does
not work, change the batteries
and press the RESET button for
2-3 seconds before use.
➢
This is a special remote control for the visually impaired, and has Braille points on the
Power, Channel and Volume buttons.
English-7
Installing Batteries in the Remote Control
1.
Lift the cover at the back of the remote control upward as shown in the figure.
2.
Install two AAA size batteries.
➢
Make sure to match the “+” and “–” ends of the batteries with the diagram inside the compartment.
3.
Replace the cover.
➢
Remove the batteries and store them in a cool, dry place if you won’t be using the remote control for a long time.
The remote control can be used up to about 23 feet from the TV.
(Assuming typical TV usage, the batteries last for about one year.)
➢
If the remote control doesn’t work, check the following:
1. Is the TV power on?
2. Are the plus and minus ends of the batteries reversed?
3. Are the batteries drained?
4. Is there a power outage, or is the power cord unplugged?
5. Is there a special fluorescent light or neon sign nearby?
Connections
Connecting VHF and UHF Antennas
If your antenna has a set of leads that look like this, see “Antennas with 300 Ω Flat Twin Leads”
below.
If your antenna has one lead that looks like this, see “Antennas with 75 Ω Round Leads”.
If you have two antennas, see “Separate VHF and UHF Antennas”.
Antennas with 300
Ω Flat T
win Leads
If you are using an off-air antenna (such as a roof antenna or “rabbit ears”) that has 300 Ω twin flat leads, follow the directions below.
1.
Place the wires from the twin leads under the screws on a 300-75 Ω adapter (not
supplied).
Use a screwdriver to tighten the screws.
2.
Plug the adaptor into the ANT 1 IN (AIR) terminal on the back of the TV.
Antennas with 75 Ω Round Leads
1.
Plug the antenna lead into the ANT 1 IN (AIR) terminal on the back of the TV.
Separate VHF and UHF Antennas
If you have two separate antennas for your TV (one VHF and one UHF), you must combine the two antenna signals before connecting
the antennas to the TV. This procedure requires an optional combiner-adaptor (available at most electronics shops).
1.
Connect both antenna leads to the combiner.
UHF
VHF
2.
Plug the combiner into the ANT 1 IN (AIR) terminal on the back of the TV.
UHF
VHF
English-8
Connecting Cable TV
To connect to a cable TV system, follow the instructions below.
Cable without a Cable Box
1.
Plug the incoming cable into the ANT 2 IN (CABLE) terminal on the back of the TV.
➢
Because this TV is cable-ready, you do not need a cable box to view unscrambled cable channels.
Connecting to a Cable Box that Descrambles All Channels
1.
Find the cable that is connected to the ANT OUT terminal on your cable box.
➢
ANT IN
ANT OUT
Connecting to a Cable Box that Descrambles Some Channels
If your cable box descrambles only some channels (such as premium channels), follow the instructions below. You will need a two-way
splitter, an RF (A/B) switch, and four lengths of Antenna cable. (These items are available at most electronics stores.)
This terminal might be labeled “ANT OUT”, “VHF OUT” or simply, “OUT”.
2.
Connect the other end of this cable to the ANT 2 IN (CABLE) terminal on the back of the
TV.
1.
Find and disconnect the cable that is
ANT IN
connected to the ANT IN terminal on your
cable box.
➢
This terminal might be labeled “ANT IN”, “VHF
IN” or simply, “IN”.
2.
Connect this cable to a two-way splitter.
Incoming
cable
Splitter
3.
Connect an Antenna cable between an
OUTPUT terminal on the splitter and the IN
Incoming
cable
Splitter
Cable Box
terminal on the cable box.
4.
Connect an Antenna cable between the
ANT OUT terminal on the cable box and the
Incoming
cable
Splitter
Cable Box
RF (A/B)
Switch
B-IN terminal on the RF(A/B) switch.
5.
Connect another cable between the other
OUT terminal on the splitter and the A-IN
Incoming
cable
Incoming
cable
Splitter
Splitter
Cable Box
Cable Box
RF (A/B)
Switch
RF (A/B)
Switch
TV Rear
ANT 2 IN
(CABLE)
After you have made this connection, set the A/B switch to the “A” position for normal viewing. Set the A/B switch to the “B” position to view
scrambled channels. (When you set the A/B switch to “B”, you will need to tune your TV to the cable box’s output channel, which is usually
channel 3 or 4.)
terminal on the RF (A/B) switch.
6.
Connect the last Antenna cable between the
OUT terminal on the RF (A/B) switch and
the ANT 2 IN (CABLE) terminal on the back
of the TV.
English-9
Connecting a VCR
These instructions assume that you have already connected your TV to an antenna or a cable TV system (according to the instructions
on pages 8~9). Skip step 1 if you have not yet connected to an antenna or a cable system.
1.
Unplug the cable or
antenna from the back of
the TV.
2.
Connect the cable or
antenna to the ANT IN
terminal on the back of the
TV Rear Panel
VCR Rear Panel
5
2
➢
Each external input source device has a different back panel configuration.
➢
When connecting an external device, match the color of the connection terminal to the cable.
➢
Also, you can connect to “AV IN 2” on the side panel of TV.
Audio Cable (Not supplied)
4
Video Cable (Not supplied)
3
Antenna cable (Not supplied)
VCR.
3.
Connect an Antenna cable
between the ANT OUT
terminal on the VCR and
the ANT 1 IN (AIR) or ANT
2 IN (CABLE) terminal on
the TV.
4.
Connect a Video Cable
between the VIDEO OUT
jack on the VCR and the
AV IN 1 [VIDEO] jack on
the TV.
5.
Connect Audio Cables
between the AUDIO OUT
jacks on the VCR and the
AV IN 1 [L-AUDIO-R]
jacks on the TV.
➢
If you have a “mono”
(non-stereo) VCR, use a
Y-connector (not supplied)
to hook up to the right and
left audio input jacks of
the TV. If your VCR is
stereo, you must connect
two cables.
Connecting an S-VHS VCR
Your Samsung TV can be connected to an S-Video signal from an S-VHS VCR.
(This connection delivers a better picture as compared to a standard VHS VCR.)
TV Rear PanelTV Side Panel
VCR Rear Panel
3
Audio Cable (Not supplied)
S-Video Cable (Not supplied)
2
1
Antenna cable (Not supplied)
An S-Video cable is usually included with an S-VHS VCR. (If not, check your local electronics store.)
➢
Each external input source device has a different back panel configuration.
➢
When connecting an external device, match the color of the connection terminal to the cable.
➢
Some games may be displayed with a cut off picture when the TV is connected to a game player.
English-10
1.
To begin, follow steps 1–3
in the previous section to
connect the antenna or
cable to your VCR and
your TV.
2.
Connect an S-Video Cable
between the S-VIDEO
OUT jack on the VCR and
the AV IN2 [S-VIDEO] jack
on the TV.
3.
Connect Audio Cables
between the AUDIO OUT
jacks on the VCR and the
AV IN2 [L-AUDIO-R] jacks
on the TV.
Connecting a Second VCR to Record from the TV
Your TV can send out signals of its picture and sound to be recorded by a second VCR. To do this, connect your second VCR as
follows:
1.
TV Rear Panel
VCR Rear Panel
Connect a video cable
between the AV OUT
[VIDEO] jack on the TV
and the VIDEO IN jack on
the VCR. Refer to your
VCR’s instructions for
more information about
how to record using this
kind of connection.
2.
2
Audio Cable (Not supplied)
1
Video Cable (Not supplied)
Connect a set of audio
cables between the AV
OUT [L-AUDIO-R] jacks
on the TV and the AUDIO
IN jacks on the VCR. (The
➢
When connecting an external device, match the color of the connection terminal to the cable.
VCR input jacks might be
either on the front or on
back of the VCR.)
Connecting a Camcorder
The side panel jacks on your TV make it easy to connect a camcorder to your TV.
They allow you to view the camcorder tapes without using a VCR.
1.
TV Side Panel
1
S-Video Cable (Not supplied)
or
Video Cable (Not supplied)
Camcorder
➢
Each external input source device has a different back panel configuration.
➢
When connecting an external device, match the color of the connection terminal to the cable.
1
2
Audio Cable (Not supplied)
Connect a Video Cable (or
S-Video Cable) between
the AV IN2 [VIDEO] (or SVIDEO) jack on the TV
and the VIDEO OUT jack
on the camcorder.
2.
Connect Audio Cables
between the AV IN2 [LAUDIO-R] jacks on the TV
and the AUDIO OUT jacks
on the camcorder.
Connecting a DVD Player/Set-Top Box
The rear panel jacks on your TV make it easy to connect a DVD player/Set-Top Box to your TV.
DVD Player/Set-Top Box
2
Audio Cable (Not supplied)
Component Cable (Not supplied)
1
➢
Component video separates the video into Y (Luminance (brightness)), Pb (Blue) and Pr (Red) for
enhanced video quality. Be sure to match the component video and audio connections.
For example, if connecting the video cable to COMPONENT IN, connect the audio cable to
COMPONENT IN also.
➢
Each external input source device has a different back panel configuration.
➢
When connecting an external device, match the color of the connection terminal to the cable.
TV Rear Panel
English-11
1.
Connect a Component
Cable between the
COMPONENT IN 1 [Y, PB,
PR](or COMPONENT IN 2
[Y, PB, PR]) jacks on the TV
and the COMPONENT Y,
PB, PR jacks on the DVD
Player/Set-Top Box.
2.
Connect Audio Cables
between the COMPONENT
IN 1 [L-AUDIO-R](or
COMPONENT IN 2 [LAUDIO-R]) jacks on the TV
and the AUDIO OUT jacks
on the DVD Player/Set-Top
Box.
Connecting a DVD Player/Set-Top Box via HDMI
This connection can only be made if there is an HDMI/DVI Output jack on the external device.
TV Rear Panel
1
HDMI Cable (Not supplied)
DVD Player/Set-Top Box
or
Audio Cable (Not supplied)
DVI to HDMI Cable (Not supplied)
TV Rear Panel
What is HDMI?
• HDMI, or high-definition multimedia interface, is a next-generation interface that enables the
transmission of digital audio and video signals using a single cable without compression.
• “Multimedia interface” is a more accurate name for it especially because it allows multiple
channels of digital audio (5.1 channels).
The difference between HDMI and DVI is that the HDMI device is smaller in size, has the
HDCP (High Bandwidth Digital Copy Protection) coding feature installed, and supports
multi-channel digital audio.
➢
Each external input source device has a different back panel configuration.
➢
When connecting an external device, match the color of the connection terminal to the cable.
➢
When connecting via HDMI, you do not need to connect Audio Cables. You only need to connect Audio
cables when connecting via HDMI/DVI.
1.
Connect an HDMI Cable
between the [HDMI IN] or
[HDMI IN 1,2] on the TV
and the HDMI OUT on the
DVD player/Set-Top Box
or connect a DVI to HDMI
Cable or DVI-HDMI
Adapter between the
[HDMI IN] or [HDMI IN
1,2] jack on the TV and
the DVI jack on the DVD
player/Set-Top Box.
If connecting via
HDMI/DVI, you must also
connect audio cables.
Connect Audio Cables
between the AV IN 1
[L -AUDIO-R] jack on the
TV and the AUDIO OUT
jacks on the DVD
player/Set-Top Box.
Connecting a Digital Audio System
The rear panel jacks on your TV make it easy to connect a Digital Audio System to your TV.
Digital Audio System
TV Rear Panel
Optical Cable (Not supplied)
What is OPTICAL:?
• Converts the electric signal into an optical light signal, and transmits it through glass
fibers. S/PDIF is a transmission system of digital audio in the form of a light wave that
uses a glass conductor.
➢
5.1CH audio is possible when the TV is connected to an external device supporting 5.1CH.
➢
Each external input source device has a different back panel configuration.
AV OUT L-AUDIO-R
RF
Digital Analog HDMI
Sound Output Sound Output Sound Output
AV, S-Video
Component,
Mute
Sound Output Sound Output Sound Output
DIGITAL AUDIO OUT(OPTICAL)
RF
Digital Analog HDMI
AV, S-Video
1.
Connect an Optical Cable
between the [DIGITAL
AUDIO OUT (OPTICAL)]
jacks on the TV and the
Digital Audio Input jacks
on the Digital Audio
System.
When a Digital Audio
System is connected to
the [DIGITAL AUDIO
OUT (OPTICAL)]
terminal: Decrease the
gain (volume) of the TV,
and adjust the volume
level with the system’s
volume control.
Component,
Mute
➢
If you want to play movies by connecting DVD player or Set-Top Box with the COMPONENT or HDMI IN jacks on the TV,
connect the AUDIO OUT jacks on DVD player or Set-Top Box to an Amplifier or DVD Home Theater.
English-12
Connecting an Amplifier/DVD Home Theater
Amplifier/DVD Home Theater
Audio Cable (Not supplied)
➢
Each external input source device has a different back panel configuration.
➢
When connecting an external device, match the color of the connection terminal to the cable.
TV Rear Panel
Operation
Turning the TV On and Off
Press the POWER button on the remote control.
You can also use the POWER button on the TV.
1.
Connect Audio Cables
between the AV OUT [LAUDIO-R] on the TV and
AUDIO IN on the
Amplifier/DVD Home
Theater.
When an audio amplifier
is connected to the
“AUDIO OUT [L-AUDIOR]” terminals: Decrease
the gain (volume) of the
TV, and adjust the
volume level with the
Amplifier’s volume
control.
Plug & Play Feature
When the TV is initially powered on, basic customer settings proceed automatically and subsequently:
1.
Menu language, Channels
and Time will be set .
Start
Plug & Play
Select the language of the OSD.
Language
Move Enter Skip
Select the antennas to memorize.
Air
Cable
Air + Cable
Move Enter Skip
English
Español
Français
Plug & Play
Start
Start
Start
Press the
The message “Menu language, Channels and Time will be set.” is displayed.
Press the
automatically displayed.
2.
Press the
Press the or button to select language, then press the
“Select the antennas to memorize.” menu is automatically displayed.
3.
Press the or button to memorize the channels of the selected connection.
Press the
➢
➢
➢
POWER
ENTER
ENTER
ENTER
If the antenna is connected to ANT 1(AIR), select “Air” and if it is connected to ANT 2
(CABLE), select “Cable”.
If both ANT 1 (AIR) and ANT 2 (CABLE) are connected, select the “Air + Cable”.
In Cable mode, you can select the correct signal source among “STD”, “HRC”, and
“IRC” by pressing the
Press the
Contact your local cable company to identify the type of cable system that exists in your
particular area.
button on the remote control.
button, then “Select the language of the OSD.” menu is
button to enter the language.
button to select “Start”.
ˇ
ˆ
button to select “Start”, then press the
button, then press the or button.
ENTER
English-13
ENTER
button.
button.
Continued...
Auto Program in progress.
Auto Program is completed.
39 channels are memorized.
Air : 9, Cable : 30
Sets the current time manually or
automatically.
Clock Mode
Move Enter Skip
Enter the current date and time.
Auto Program
Stop
Enter Skip
Auto Program
OK
Enter Skip
Plug & Play
Manual
Auto
Plug & Play
Month Day Year
--
--
Hour Minute am/pm
--
----
-- --
Air 16
15%
4.
The TV will begin memorizing all of the available channels.
After all the available channels are stored, the Auto program menu reappears.
Press the
ENTER
button when channel memorization is complete.
“Clock Mode.” menu is automatically displayed.
➢
To stop the search before it has finished, press the
5.
Press the
ENTER
button.
ENTER
button with stop selected.
Press the or button to select “Manual” for setting the current time manually,
then press the
➢
If you select “Auto”, “Set to daylight savings time.” is displayed, then go to step
6.
Press the ˇor ˆbutton to move to “Month”, “Day”, “Year”, “Hour”, “Minute”, or
ENTER
button. “Enter the current date and time.” is displayed.
“am/pm”. Set the date and time you want by pressing the or button, then
press the
➢
MENU
You can set the Month, Day, Year, Hour, and Minute directly by pressing the number
buttons on the remote control.
button.
8
.
Move Adjust Skip
Enjoy your watching.
OK
Setting the Clock
Set to daylight savings time.
DST
Move Enter Skip
Select the time zone where you are
located.
Newfoundland
Atlantic
Eastern
Central
Mountain
Pacific
Alaska
Hawaii
Move Enter Skip
Automatically
Plug & Play
On
Off
Plug & Play
Enjoy your watching.
OK
7.
The message “Enjoy your watching.” is displayed.
When you have finished,press the
➢
Even if the
after several seconds.
8.
Press the
ENTER
ENTER
button is not pressed, the message will automatically disappear
button.
Press the or button to select “On” or “Off”, then the
ENTER
button.
ENTER
button.
“Select the time zone where you are located.” menu is automatically displayed.
9.
Press the or button to highlight the time zone for your local area (and to
move the highlight to the appropriate time zone on the map of the United
States). Press the
ENTER
button.
If not, see pages 35~36 to set the clock.
10.
The message “Enjoy your watching.” is displayed.
When you have finished,press the
➢
Even if the
after several seconds.
ENTER
button is not pressed, the message will automatically disappear
ENTER
button.
English-14
Continued...
If you want to reset this feature...
Setup
Plug & Play
Language : English
Time
V-Chip
Caption
Menu Transparency: Medium
Blue Screen : Off
Function Help : On
Move Enter Return
Menu language, Channels
and Time will be set .
Start
1. Press the MENU button to display the menu.
ˆ
ˆ
ˆ
ˆ
ˆ
ˆ
ˆ
ˆ
Press the or
2. Press the ENTER button to select “Plug & Play”.
For further details on setting up options, refer to the pages 13~14.
➢
Plug & Play can only be accessed in the TV mode.
Changing Channels
Using the Channel Buttons
1.
Press the
➢
When you press the CHor
You will see all the channels that the TV has memorized. (The TV must have
memorized at least three channels). You will not see channels that were either erased
or not memorized. See page 17 to memorize channels.
Using the Number
Use the number buttons to quickly tune to any channel.
Buttons
1.
Press the number buttons to go directly to a channel.
For example, to select channel 27, press “2,” then “7.”
The TV will change channels when you press the second number.
button to select “Setup”, then press the ENTER button.
CH
or
CH
button to change channels.
CH
button, the TV changes channels in sequence.
Using the “-” Button
The “-” button is used to select channels that broadcast a digital signal.
1.
For example, for channel 7 (digital), press “7”, then “-”, then “1”.
HD indicates the TV is receiving a digital High Definition signal. SD indicates the
TV is receiving an analog Standard Definition signal.
Using the PRE-CH Button to select the Pr
evious Channel
1.
Press the
PRE-CH
The TV will switch to the last channel viewed.
➢
To quickly switch between two channels that are far apart, tune to one channel, then
use the number button to select the second channel. Then use the
quickly alternate between them.
English-15
button.
PRE-CH
button to
Adjusting the Volume
1.
Press the
VOL +
or
VOL –
button to increase or decrease the volume.
Using Mute Button
At any time, you can cut off the sound using the MUTE button.
1.
Press
MUTE
and the sound cuts off.
The word “MUTE” will appear in the lower-left corner of the screen.
2.
To turn mute off, press the
VOL –
button.
MUTE
button again, or simply press the
Viewing the Display
The display identifies the current channel and the status of certain audio-video settings.
1.
Air 13
Mono
Picture Mode : Dynamic
Sound Mode : Custom
MTS : Stereo
Caption : Off
V-Chip : Off
No Time Information
Press the
The TV will display the channel, the type of sound, and the status of certain
picture and sound settings.
INFO
button on the remote control.
VOL +
or
Viewing the Menus
Input
Source List : TV
Edit Name
Move Enter Return
Press the INFO button once more or wait approximately 10 seconds and it disappears
automatically.
1.
With the power on, press the
ˆ
ˆ
The main menu appears on the screen. Its left side has five icons:
“Input”, “Picture”, “Sound”, “Channel”, “Setup”.
2.
Use the or button to select one of the five icons.
MENU
button.
Then press the ENTER button to access the icon’s sub-menu.
3.
Press the
➢
The on-screen menus disappear from the screen after a few seconds.
EXIT
button to exit.
English-16
Loading...