Samsung TX-R2735G User Manual

TX-R2728G TX-R2734G TX-R2735G

COLOR TELEVISION

Owner’s Instructions

Important Warranty Information Regarding Television Format Viewing

Standard screen format televisions (4:3, the aspect ratio of the screen width to height) are primarily designed to view standard format full-motion video. The images displayed on them should primarily be in the standard 4:3 ratio format and constantly moving. Displaying stationary graphics and images on screen, such as the dark top and bottom letterbox bars (wide screen pictures), should be limited to no more than 15% of the total television viewing per week.

Wide screen format televisions (16:9, the aspect ratio of the screen width to height) are primarily designed to view wide screen format full-motion video. The images displayed on them should primarily be in the wide screen 16:9 ratio format, or expanded to fill the screen if your model offers this feature, and constantly moving. Displaying stationary graphics and images on screen, such as the dark side-bars on non-expanded standard format television video and programming, should be limited to no more than 15% of the total television viewing per week.

Additionally, viewing other stationary images and text such as stock market reports, video game displays, station logos, web sites or computer graphics and patterns, should be limited as described above for all televisions. Displaying any stationary images that exceed the above guidelines can cause uneven aging of picture tubes (CRTs) that leave subtle, but permanent burned-in ghost images in the television picture. To avoid this, vary the programming and images, and primarily display full screen moving images, not stationary patterns or dark bars. On television models that offer picture sizing features, use these controls to view the different formats as a full screen picture.

Be careful in the selection and duration of television formats used for viewing. Uneven CRT aging as a result of format selection and use, as well as other burned-in images, is not covered by your Samsung limited warranty.

English - 2

CONTENTS

Chapter 1: Your New TV . . . . . . . . . . . . . . . . 5

List of Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Familiarizing Yourself with The TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Front Panel Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Side Panel Jacks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Rear Panel Jacks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Remote Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Chapter 2: Installation . . . . . . . . . . . . . . . . . 10

Connecting VHF and UHF Antennas . . . . . . . . . . . . . . . . . . . . . . . . . 10

Antennas with 300-ohm Flat Twin Leads . . . . . . . . . . . . . . . 10

Antennas with 75-ohm Round Leads . . . . . . . . . . . . . . . . . . 11

Separate VHF and UHF Antennas . . . . . . . . . . . . . . . . . . . . . 11

Connecting Cable TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Cable without a Cable Box . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Connecting to a Cable Box that Descrambles All Channels . . 12 Connecting to a Cable Box that Descrambles Some Channels 12

Connecting a VCR. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Connecting an S-VHS VCR . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Connecting a Second VCR to Record from the TV. . . . . . . . . 16

Connecting a DVD Player . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Connecting a Camcorder. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Installing Batteries in the Remote Control . . . . . . . . . . . . . . . . . . . . . . 19

Chapter 3: Operation . . . . . . . . . . . . . . . . . . 20

Tu r ning the TV On and Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Plug & Play Feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Viewing the Menus and On-Screen Displays . . . . . . . . . . . . . . . . . . . . 22

Viewing the Menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Viewing the Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Selecting a Menu Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Memorizing the Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Selecting the Video Signal-source . . . . . . . . . . . . . . . . . . . . . 24

Storing Channels in Memory (Automatic Method) . . . . . . . . 25

Adding and Erasing Channels (Manual Method). . . . . . . . . . 26

Changing Channels. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Using the Channel Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Directly Accessing Channels . . . . . . . . . . . . . . . . . . . . . . . . . 27

Using the PRE-CH Button to Select the Previous Channel. . . 27

Labeling the Channels. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Setting the Clock. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Customizing the Picture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Using Automatic Picture Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Adjusting the Volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Using the Mute Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Customizing the Sound. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Using Automatic Sound Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Viewing an External Signal Source . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Setting the Signal Source. . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Assigning Names to External input mode . . . . . . . . . . . . . . . 38

English - 3

CONTENTS

Chapter 4: Special Features. . . . . . . . . . . . . 39

Changing the Color Tone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Changing the Screen Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Digital Noise Reduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Using the R.Surf Feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Choosing a Multi-Channel Sound (MTS) Soundtrack . . . . . . . . . . . . . 43

Extra sound settings (Auto Volume, Turbo Sound or Pseudo Stereo) . . 44

Setting the On/Off Timer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Setting the Sleep Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Setting the Preferred Volume Level . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Using the V-Chip. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Viewing Closed Captions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

Setting the Blue Screen Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

Setting The On/Off Melody . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

Viewing the Demonstration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

Chapter 5: Troubleshooting . . . . . . . . . . . . . 60

Identifying Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

Cleaning and Maintaining Your TV . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

Using Your TV in Another Country . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

English - 4

Chapter One

YOUR NEW TV

List of Features

Your TV is designed with the latest technology. This TV is a high-performance unit that includes the following special features:

• Full Flat Screen

• Easy-to-use remote control

• Easy-to-use on-screen menu system

•Automatic timer to turn the TV on and off

• Adjustable picture and sound settings that can be stored in the TV’s memory

• Automatic channel tuning for up to 181 channels

•A special filter to reduce or eliminate reception problems

•A built-in multi-channel sound decoder for stereo and bilingual listening

• Built-in, dual channel speakers

•A special sleep timer

•V-Chip function

Accessories

Once you have unpacked your TV, check to make sure that you have all the parts shown here. If any piece is missing or broken, call your dealer.

Remote Control(AA59-00316B)/

AAA Batteries

Owner’s Instructions

Safety Guide Manual

Warranty Card/

Registration Card

English - 5

YOUR NEW TV

Familiarizing Yourself with The TV

Front Panel Buttons

The buttons on the front panel control your TV’s basic features, including the on-screen menu. To use the more advanced features, you must use the remote control.

TX-R2728G

TX-R2734G

TX-R2735G

Press to see an on-screen menu of your TV's features.

VOL – and +

Press to increase or decrease the volume. Also used to select items on the on-screen menu.

CH (▼) and CH (▲)

Press to change channels. Also press to highlight various items on the on-screen menu.

Remote Control Sensor

Aim the remote control towards this spot on the TV.

English - 6

TIMER indicator

When the TV is turned on, the TIMER indicator blinks five times. This indicator illuminates when the TIMER mode is set to the “On” position after setting the clock and either the On timer or Off timer, with the remote control. Even if the power is turned off, this indicator stays lit. (Clock must be set before using this function.)

POWER

Press to turn the TV on and off.

YOUR NEW TV

Connection Jacks (Side)

You can connect an A/V component that is used only occasionally, such as a camcorder or video game. (For information on connecting equipment, see page 18.)

TX-R2728G

AUDIO INPUT jacks

Used to connect the audio signals from a camcorder or video game.

VIDEO INPUT jack

Used to connect a video signal from a camcorder or video game.

TX-R2734G / TX-R2735G

SUPER VIDEO INPUT jack

S-Video signal from an S-VHS VCR or DVD player. Note: In S-Video mode, Audio Output depends what kind of audio input source is connected to the side audio input jacks (AV2).

• Please be sure to match the color coded input terminals and cable jacks.

English - 7

YOUR NEW TV

Connection Jacks (Rear)

Use the rear panel jacks to connect an A/V component that will be connected continuously, such as a VCR or a DVD player. Because there are two sets of input jacks, you can connect two different A/V components (i.e., a VCR and a DVD, 2 VCRs, etc.)

For more information on connecting equipment, see pages 10 – 17.

VIDEO Input

Video signals from VCRs, DVD players and similar devices.

AUDIO Input (INPUT1 and 2) / COMPONENT AUDIO Input

(INPUT 2)

Audio signals from VCRs, DVD players and similar devices. Use these jacks to connect the audio signals from a DVD player when using the DVD video input jacks. When not using the DVD jacks, these audio jacks function as audio for Video 2 or S-VIDEO.

S-VIDEO Input

S-Video signal from an S-VHS VCR or DVD player. Note: In S-Video mode, Audio Output depends what kind of audio input source is connected to the side audio input jacks (AV2).

COMPONENT VIDEO Input

Connect video from a DVD player. Note: Only black and white signals are output from a monitor in DVD mode.

VHF/UHF

Connect to an antenna or to a cable TV system.

AUDIO-VIDEO MONITOR Output

These audio-video signals are identical to A/V signals being displayed on the big screen. (Typically used as the input signals for a recording VCR.)

English - 8

YOUR NEW TV

Remote Control

You can use the remote control up to about 23 feet from the TV. When using the remote, always point it directly at the TV.

POWER

Turns the TV on and off.

Number buttons

Press to select channels directly on the TV.

+100

Press to select channels over 100. For example, to select channel 121, press “+100,” then press “2” and “1.”

MUTE

Press to temporarily cut off the sound.

VOL -, VOL +

Press to increase or decrease the volume.

’

PRE-CH

Tunes to the previous channel.

TV/VIDEO

Press to display all of the available video sources (i.e., Antenna/Cable, VCR).

CH and CH (Channel Up/Down)

Press CH or CH to change channels.



INFO

Press to see the time, channel, etc., on-screen. Also press to exit (quit) the menu system.

EXIT

Press the menu to exit.

SLEEP

Press to select a preset time interval for automatic shutoff.

∏

Displays the main on-screen menu.

”

MTS (Multichannel Television Stereo)

Press to choose stereo, mono or Separate Audio Program (SAP broadcast).

▲,▼,œ,√ / ENTER

Press to select highlight up, down, left, or right. While using the onscreen menus, press ENTER to activate (or change) a particular item.

R.SURF

Press the R.SURF button to automatically return to a preferred channel after a user-preset time delay.

CH SCAN

Not available.

TURBO

Press to turn the TURBO sound On or Off.

English - 9

Chapter Two

INSTALLATION

Connecting VHF and UHF Antennas

If your antenna has a set of leads that look like this, see “Antennas with 300-ohm Flat Twin Leads” below.

If your antenna has one lead that looks like this, see “Antennas with 75-ohm Round Leads” on next page.

If you have two antennas, see “Separate VHF and UHF Antennas” on next page.

Antennas with 300-ohm Flat Twin Leads

If you are using an off-air antenna (such as a roof antenna or “rabbit ears”) that has 300-ohm twin flat leads, follow the directions below.

Place the wires from the twin leads under the screws on the 300-75 ohm adaptor (not supplied). Use a screwdriver to tighten the screws.

Plug the adaptor into the VHF/UHF terminal on the bottom of the back panel.

English - 10

INSTALLATION

Antennas with 75-ohm Round Leads

Plug the antenna lead into the VHF/UHF terminal on the bottom of the back panel.

Separate VHF and UHF Antennas

If you have two separate antennas for your TV (one VHF and one UHF), you must combine the two antenna signals before connecting the antennas to the TV. This procedure requires an optional combiner-adaptor (available at most electronics shops).

Connect both antenna leads to the combiner.

Plug the combiner into the VHF/UHF terminal on the bottom of the rear panel.

Connecting Cable TV

To connect to a cable TV system, follow the instructions below.

Cable without a Cable Box

▼

Plug the incoming cable into the VHF/UHF antenna terminal on back of the TV.

Because this TV is cable-ready, you do not need a cable box to view unscrambled cable channels.

English - 11

INSTALLATION

Connecting to a Cable Box that Descrambles All Channels

▼

Find the cable that is connected to the ANTENNA OUT terminal on your cable box.

This terminal might be labeled “ANT OUT”, “VHF OUT” or simply, “OUT”.

Connect the other end of this cable to the VHF/UHF antenna terminal on the back of the TV.

Connecting to a Cable Box that Descrambles Some Channels

If your cable box descrambles only some channels (such as premium channels), follow the instructions below. You will need a two-way splitter, an RF (A/B) switch, and four lengths of coaxial cable. (These items are available at most electronics stores.)

Find and disconnect the cable that is connected to the ANTENNA IN terminal on your cable box.

Connect this cable to a two-way splitter.

Connect a coaxial cable between an OUTPUT terminal on the splitter and the IN terminal on the cable box.

Incoming Cable

Splitter

▼

This terminal might be labeled “ANT IN”, “VHF IN” or simply, “IN”.

Splitter

Cable Box

English - 12

INSTALLATION

Connect a coaxial cable between the ANTENNA OUT terminal on the cable box and the B–IN terminal on the RF (A/B) switch.

Connect another cable between the other OUT terminal on the splitter and the A–IN terminal on the RF (A/B) switch.

Connect the last coaxial cable between the OUT terminal on the RF (A/B) switch and the VHF/UHF terminal on the rear of the TV.

Incomin g Cable

Splitter

Cable Box

RF (A/B)

Switch

RF (A/B)

Switch

RF (A/B)

Switch

TV Rear

After you’ve made this connection, set the A/B switch to the “A” position for normal viewing. Set the A/B switch to the “B” position to view scrambled channels. (When you set the A/B switch to “B”, you will need to tune your TV to the cable box’s output channel, which is usually channel 3 or 4.)

English - 13

INSTALLATION

Connecting a VCR

These instructions assume that you have already connected your TV to an antenna or a cable TV system (according to the instructions on pages 10-13). Skip step 1 if you have not yet connected to an antenna or a cable system.

Unplug the cable or antenna from the back of the TV.

Connect the cable or antenna to the ANTENNA IN terminal on the back of the VCR.

Connect a coaxial cable between the ANTENNA OUT terminal on the VCR and the antenna terminal on the TV.

Incoming Cable or Antenna

VCR Rear Panel

TV Rear Panel

Coaxial Cable

A coaxial cable is usually included with a VCR. (If not, check your local electronics store).

Connect a set of audio cables between the AUDIO OUT jacks on the VCR and the AUDIO jacks on the TV.

VCR Rear Panel

Audio Cable

TV Rear Panel

Connect a video cable between the VIDEO OUT jack on the VCR and the VIDEO jack on the TV.

VCR Rear Panel

Video Cable

Follow the instructions in “Viewing an External Signal Source” to view your VCR tape.

English - 14

TV Rear Panel

INSTALLATION

Connecting an S-VHS VCR

Your Samsung TV can be connected to an S-Video signal from an S-VHS VCR. (This connection delivers a better picture as compared to a standard VHS VCR.)

To begin, follow steps 1–3 in the previous section to connect the antenna or cable to your VCR and your TV.

Connect a set of audio cables between the AUDIO OUT jacks on the VCR and the 2 AUDIO INPUT jacks on the TV.

VCR Rear Panel

TV Rear Panel

Coaxial Cable

TV Rear Panel

Audio Cable

Make sure the jacks you are using are underneath the number “2.”

Connect an S-video cable between the S-VIDEO OUT jack on the VCR and the S-VIDEO INPUT jack on the TV.

VCR Rear Panel

Video Cable

TV Rear Panel

An S-video cable is usually included with an S-VHS VCR. (If not, check your local electronics store.)

English - 15

INSTALLATION

Connecting a Second VCR to Record from the TV

Your TV can send out signals of its picture and sound to be recorded by a second VCR. To do this, connect your second VCR as follows:

Connect a set of audio cables between the AUDIO OUT jacks on the TV and the AUDIO IN jacks on the VCR.

TV Rear Panel

VCR Input Panel

Audio Cable

(The VCR input jacks might be either on the front or on back of the VCR.)

Connect a video cable between the VIDEO OUT jack on the TV and the VIDEO IN jack on the VCR.

TV Rear Panel

Video Cable

Refer to your VCR’s instructions for more information about how to record using this kind of connection.

VCR Input Panel

English - 16

INSTALLATION

Connecting a DVD Player

The rear panel jacks on your TV make it easy to connect a DVD player to your TV.

Connect a set of audio cables between the AUDIO INPUT 2 jacks on the TV and the AUDIO OUT jacks on the DVD player.

Connect a video cable between the COMPONENT INPUT (Y, Pb, Pr) jacks on the TV and the COMPONENT VIDEO OUT (Y, P jacks on the DVD player.

, PR)

DVD Player Rear Panel

Audio Cable

DVD Player Rear Panel

Video Cable

TV Rear Panel

Note: For an explanation of Component video, see your DVD player's owner's manual.

English - 17

INSTALLATION

Connecting a Camcorder

The side panel jacks on your TV make it easy to connect a camcorder to your TV. They allow you to view the camcorder tapes without using a VCR. (Also see “Viewing an External Signal Source” on page 37)

Locate the A/V output jacks on the camcorder. They are usually found on the side or back of the camcorder.

Camcorder

Output Jacks

Connect an audio cable between the AUDIO OUTPUT jack on the camcorder and the AUDIO terminals on the side of the TV.

Connect a video cable between the VIDEO OUTPUT jack on the camcorder and the VIDEO terminal on the side of the TV.

Camcorder

Output Jacks

Camcorder

Output Jacks

Audio Cable

Y-Connector

Video Cable

TV Side Panel

The audio-video cables shown here are usually included with a Camcorder. (If not, check your local electronics store.) If your camcorder is stereo, you need to connect a set of two cables.

Note: This figure shows the Standard connector-jack panel. The actual configuration for your TV may be different.

English - 18

INSTALLATION

Installing Batteries in the Remote Control

Slide the cover out completely.

▼

Install two AAA size batteries.

Make sure to match the “+” and

“

–” ends of the batteries with the

diagram inside the compartment.

Replace the cover.

▼

Remove the batteries and store them in a cool, dry place if you won’t be using the remote control for a long time.

The remote control can be used up to about 23 feet from the TV.

(Assuming typical TV usage, the batteries last for about one year.)

English - 19

OPERATION

Chapter Three

OPERATION

Turning the TV On and Off

Press the POWER button on the remote control.

Yo u can also use the POWER button on the front panel.

Plug & Play Feature

When the TV is initially powered On, five basic customer settings proceed automatically and subsequently: Setting the language, Video signal source, Ant. input check, Auto program and Clock.

Press the POWER button on the remote control.

The message “Plug & Play” is displayed. It flickers for a little while and then the “Language” menu is automatically displayed.

Press the to select the desired language.

œœ

or √√button

Press the MENU button then the “Ant Input check” is automatically displayed. Make sure that the antenna is connected to the TV. Press the ENTER button and then the “Channel” menu is automatically displayed.

Plug & Play

▲

Language : English

Blue Screen : On

Melody : On Demonstration

Adjust Skip

Ant Input check

Auto Program Skip

Setup

√√ √√ √√

Press the select signal source (Air, STD, HRC, IRC).

œœ or√√

button to

Channel

Auto Program

Add/Delete : Deleted

Air/CATV : Air

Name :

----

Adjust Skip

English - 20

√√ √√

+ 44 hidden pages