Samsung TXL 2791F, TXM 2790F, TXM3292F User Manual

TXL2791F TXM2790F TXM3292F

..........................................................................................................................

COLOR TELEVISION

AA68-01698B-00(ENG)

.............

Owner’s Instructions

Warning! Important

Safety Instructions

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

This symbol indicates high voltage is present inside. It is dangerous to make any kind of contact with any inside part of this product.

This symbol alerts you that important literature concerning operation and maintenance has been included with this product.

Note to CATV system installer: This reminder is provided to call CATV system installer’s attention to Article 820-40 of the National Electrical Code (Section 54 of Canadian Electrical Code, Part I), that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building as close to the point of cable entry as practical.

Caution: FCC/CSA regulations state that any unauthorized changes or modifications to this equipment may void the user’s authority to operate it.

Caution: To prevent electric shock, match the wide blade of plug to the wide slot, and fully insert the plug.

Attention: pour eviter les chocs electriques, introduire la lame le plus large de la fiche dans la borne correspondante de la prise et pousser jusqu’au fond.

Important: One Federal Court has held that unauthorized recording of

copyrighted TV programs is an infringement of U.S. copyright laws. Certain Canadian programs may also be copyrighted and any unauthorized

recording in whole or in part may be in violation of these rights.

To prevent damage which may result in fire or electric shock hazard, do not expose this appliance to rain or moisture.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

As an ENERGY ST AR Partner , Samsung Electronics America, Inc. has determined that this product or product model meets the ENERGY ST AR guidelines for energy efficiency.

AFETY

Thank You for Choosing Samsung

Thank you for choosing Samsung! Your new Samsung TV represents the latest in television technology. We designed it with easy-to-use on-screen menus and closed captioning capabilities, making it one of the best products in its class. We are proud to offer you a product that will provide convenient, dependable service and enjoyment for years to come.

Important Safety Information

Always be careful when using your TV receiver. To reduce the risk of fire, electrical shock, and other injuries, keep these safety precautions in mind when installing, using, and maintaining your machine.

• Read all safety and operating instructions before operating your TV.

• Keep the safety and operating instructions for future reference.

• Heed all warnings on the TV receiver and in the operating instructions.

• Follow all operating and use instructions.

• Unplug the TV receiver from the wall outlet before cleaning. Use a damp cloth; do not use liquid or aerosol cleaners.

• Never add any attachments and/or equipment without approval of the manufacturer. Such additions can increase the risk of fire, electric shock, or other personal injury.

• Do not use the TV receiver where contact with or immersion in water is a possibility, such as near bath tubs, sinks, washing machines, swimming pools, etc.

• Do not place the TV on an unstable cart, stand, tripod, bracket, or table where it can fall. A falling TV can cause serious injury to a child or adult, and serious damage to the appliance. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer or sold with the TV. Follow the manufacturer’s instructions when mounting the unit, and use a mounting accessory recommended by the manufacturer. Move the TV and cart with care. Quick stops, excessive force, and uneven surfaces can make the unit and cart unsteady and likely to overturn.

• Provide ventilation for the TV receiver. The unit is designed with slots in the cabinet for ventilation to protect it from overheating. Do not block these openings with any object, and do not place the TV receiver on a bed, sofa, rug, or other similar surface. Do not place it near a radiator or heat register. If you place the TV receiver on a rack or bookcase, ensure that there is adequate ventilation and that you’ve followed the manufacturer’s instructions for mounting.

• Operate your TV receiver only from the type of power source indicated on the marking label. If you are not sure of the type of power supplied to your home, consult your appliance dealer or local power company.

• Use only a grounded or polarized outlet. For your safety, this TV is equipped with a polarized alternating current line plug having one blade wider than the other. This plug will fit into the power outlet only one way. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug still does not fit, contact your electrician to replace your outlet.

• Protect the power cord. Power supply cords should be routed so that they won’t be walked on or pinched by objects placed on or against them. Pay particular attention to cords at plugs, convenience receptacles, and the point where they exit from the unit.

• Unplug the TV from the wall outlet and disconnect the antenna or cable system during a lightning storm or when left unattended and unused for long periods of time. This will prevent damage to the unit due to lightning and power-line surges.

• Avoid overhead power lines. An outside antenna system should not be placed in the vicinity of overhead power lines or other electric light or power circuits or where it can fall into such power lines or circuits. When installing an outside antenna system, be extremely careful to keep from touching the power lines or circuits. Contact with such lines can be fatal.

• Do not overload the wall outlet or extension cords. Overloading can result in fire or electric shock.

• Do not insert anything through the openings in the unit, where they can touch dangerous voltage points or damage parts. Never spill liquid of any kind on the TV.

• Ground outdoor antennas. If an outside antenna or cable system is connected to the TV, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Section 810 of the National Electrical Code, ANSI/NFPA No.70-1984, provides information about proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.

• Do not attempt to service the TV yourself. Refer all servicing to qualified service personnel. Unplug the unit from the wall outlet and refer servicing to qualified service personnel under the following conditions:

- when the power-supply cord or plug is damaged

- if liquid has been spilled on the unit or if objects have fallen into the unit

- if the TV has been exposed to rain or water

- if the TV does not operate normally by following the operating instructions

- if the TV has been dropped or the cabinet has been damaged

- when the TV exhibits a distinct change in performance

• If you make adjustments yourself, adjust only those controls that are covered by the operating instructions. Adjusting other controls may result in damage and will often require extensive work by a qualified technician to restore the TV to normal.

• When replacement parts are required, be sure the service technician uses replacement parts specified by the manufacturer or those that have the same characteristics as the original part. Unauthorized substitutions may result in additional damage to the unit.

• Upon completion of any service or repairs to this TV, ask the service technician to perform safety checks to determine that the TV is in a safe operating condition.

AFETY

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference that may cause undesired operation.

This television receiver provides display of television closed captioning in accordance with

§15.119 of the FCC rules.

EXAMPLE OF ANTENNA GROUNDING

GROUND CLAMP

ELECTRIC SERVICE EQUIPMENT

NEC — NATIONAL ELECTRICAL CODE

GROUND CLAMPS

POWER SERVICE GROUNDING ELECTRODE SYSTEM (NEC ART 250, PART H)

ANTENNA LEAD IN WIRE

ANTENNA DISCHARGE UNIT (NEC SECTION 810-20)

GROUNDING CONDUCTORS (NEC SECTION 810-21)

CONTENTS

ONTENTS

Chapter 1: Your New TV . . . . . . . . . . . . . . .1.1

List of Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.1

Familiarizing Yourself with The TV. . . . . . . . . . . . . . . . . . . . . . . . . . 1.2

Front Panel Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.2

Front/Side Panel Jacks . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.3

Rear Panel Jacks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.4

Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.5

Chapter 2: Installation . . . . . . . . . . . . . . . . 2.1

Connecting VHF and UHF Antennas . . . . . . . . . . . . . . . . . . . . . . . . 2.1

Antennas with 300-ohm Flat Twin Leads . . . . . . . . . . . . . . 2.1

Antennas with 75-ohm Round Leads . . . . . . . . . . . . . . . . . 2.2

Separate VHF and UHF Antennas. . . . . . . . . . . . . . . . . . . . 2.2

Connecting Cable TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.2

Cable without a Cable Box. . . . . . . . . . . . . . . . . . . . . . . . . 2.2

Connecting to a Cable Box that Descrambles

All Channels. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.3

Connecting to a Cable Box that Descrambles

some Channels. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.3

Connecting a VCR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.4

Connecting an S-VHS VCR. . . . . . . . . . . . . . . . . . . . . . . . . 2.6

Connecting a Second VCR to Record from the TV . . . . . . . 2.7

Connecting a DVD Player. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.7

Connecting a Camcorder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.8

Installing Batteries in the Remote Control. . . . . . . . . . . . . . . . . . . . . 2.9

Chapter 3: Operation. . . . . . . . . . . . . . . . . . 3.1

Turning the TV On and Off. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.1

Plug & Play Feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.1

Viewing the Menus and On-Screen Displays. . . . . . . . . . . . . . . . . . . 3.3

Viewing the Menus. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.3

Viewing the Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.3

Selecting a Menu Language. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.4

Memorizing the Channels. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.5

Selecting the Video Signal-source. . . . . . . . . . . . . . . . . . . . 3.5

Storing Channels in Memory (Automatic Method). . . . . . . 3.6

Adding and Erasing Channels (Manual Method) . . . . . . . . 3.7

Changing Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.8

Using the Channel Buttons. . . . . . . . . . . . . . . . . . . . . . . . . 3.8

Directly Accessing Channels. . . . . . . . . . . . . . . . . . . . . . . . 3.8

Using the PRE-CH Button to select the Previous Channel. . 3.8

Adjusting the Volume. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.8

Using Mute. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.8

Labeling the Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.9

Setting the Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.10

Option 1: Setting the Clock Manually . . . . . . . . . . . . . . . . 3.10

Option 2: Using the Local PBS Channel to

Automatically Set the TV Clock . . . . . . . . . . . . . . . . . . . . . 3.11

Customizing the Picture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.13

Using Automatic Picture Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.14

Customizing the Sound . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.15

Using Automatic Sound Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.16

Setting The On/Off Melody. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.17

Viewing a VCR or Camcorder Tape. . . . . . . . . . . . . . . . . . . . . . . . . . 3.18

CONTENTS

Chapter 4: Special Features . . . . . . . . . . . . 4.1

Customizing Your Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . 4.1

Setting Up Your Remote Control to Operate Your VCR. . . . 4.1

Setting Up Your Remote Control to

Operate Your Cable Box . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.3

Fine Tuning Channels. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.4

Digital Noise Reduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.5

Title . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.6

Changing the Screen Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.7

Using the R.Surf Feature. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.8

Setting the On/Off Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.9

Setting the Sleep Timer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.10

Sound Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.11

Choosing a Multi-Channel Sound (MTS) Soundtrack. . . . . 4.11

Extra sound settings

(Turbo Sound, Surround, or Auto Volume) . . . . . . . . . . . . 4.12

Viewing Closed Captions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.13

Using the V-Chip (Only USA). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.14

Setting Up Your Personal ID Number (PIN) . . . . . . . . . . . . 4.14

How to Enable/Disable the V-Chip. . . . . . . . . . . . . . . . . . . 4.15

How to Set up Restrictions Using the “TV guidelines” . . . . 4.15

How to Set up Restrictions using the MPAA Ratings:

G, PG, PG-13, R, NC-17, X . . . . . . . . . . . . . . . . . . . . . . . . 4.17

How to Reset the TV after the V-Chip Blocks

a Channel (“Emergency Escape”) . . . . . . . . . . . . . . . . . . . . 4.18

Chapter 5: Troubleshooting . . . . . . . . . . . . 5.1

Identifying Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.1

Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . A.1

Cleaning and Maintaining Your TV. . . . . . . . . . . . . . . . . . . . . . . . . . A.1

Using Your TV in Another Country . . . . . . . . . . . . . . . . . . . . . . . . . A.1

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A.1

CHAPTER ONE: YOUR NEW TV 1.1

List of Features

Your TV was designed with the latest technology. This TV is a high-performance unit that includes the following special features:

• Easy-to-use remote control

• Easy-to-use on-screen menu system

• Automatic timer to turn the TV on and off

• Adjustable picture and sound settings that can be stored in the TV’s memory

• Automatic channel tuning for up to 181 channels

• A special filter to reduce or eliminate reception problems

• Fine tuning control for the sharpest picture possible

• A built-in multi-channel sound decoder for stereo and bilingual listening

• Built-in, dual channel speakers

• A special sleep timer

• Headphone jack for private listening

• 16:9 letter box format available depending upon source

Chapter One

YOUR NEW TV

1.2 CHAPTER ONE: YOUR NEW TV

Familiarizing Yourself with The TV

Front Panel Buttons

The buttons on the front panel control your TV’s basic features, including the on-screen menu. To use the more advanced features, you must use the remote control.

YOUR NEW TV

TV/VIDEO (TXM3292F)

Press to change between viewing TV programs and signals from other components.

Press to see an on-screen menu of your TV's features.

VOL – , + (Volume)

Press to increase or decrease the volume. Also used to select items on the onscreen menu.

CH ▼ and CH ▲ (Channel)

Press to change channels. Also press to highlight various items on the on-screen menu.

Remote Control Sensor

Aim the remote control towards this spot on the TV.

POWER & TIMER indicator

When the TV is turned on, the POWER & TIMER indicator blinks ten times. This indicator illuminates when the TIMER mode is set to the “On” position after setting the clock and either the On timer or Off timer, with the remote control. Even if the power is turned off, this indicator stays lit. (Clock must be set before using this function.)

∏

POWER

Press to turn the TV on and off.

For model TXL2791F

For model TXM2790F

For model TXM3292F

CHAPTER ONE: YOUR NEW TV 1.3

YOUR NEW TV

Front/Side Panel Jacks

You can use the front/Side panel jacks to connect an A/V component that is used only occasionally, such as a camcorder or video game. (For information on connecting equipment, see pages 2.1 – 2.8.)

AUDIO INPUTS

Used to connect the audio signals from a camcorder or video game.

VIDEO INPUT

Used to connect a video signal from a camcorder or a video game.

S-VIDEO INPUT jack (TXM3292F)

Used to connect an S-Video signal from a camcorder or a video game.

HEADPHONE JACK

Connect a set of external headphones to this jack for private listening.

For model TXL2791F For model TXM3292F

For model TXM2790F

1.4 CHAPTER ONE: YOUR NEW TV

YOUR NEW TV

Rear Panel Jacks

Use the rear panel jacks to connect an A/V component that will be connected continuously, such as a VCR or a laserdisc player. Because there are two sets of input jacks, you can connect two different A/V components (i.e., a VCR and a laserdisc, 2 VCRs, etc.)

For more information on connecting equipment, see pages 2.1 – 2.8.

VIDEO INPUT jack

Video signals from VCRs, DVD players and similar devices.

AUDIO INPUTS(INPUT1 and 2)/ DVD AUDIO INPUTS

(INPUT 2)

Audio signals from VCRs, DVD players and similar devices.

Use these jacks to connect the audio signals from a DVD player when using the DVD video input jacks. When not using the DVD jacks, these audio jacks function as audio for Video 2 or SVIDEO).

AUDIO-VIDEO MONITOR OUTPUT jacks

These audio-video signals are identical to A/V signals being displayed on the big screen. (Typically used as the input signals for a recording VCR.)

SUPER VIDEO INPUT jack (For models TXL2791F/ TXM3292F)

S-Video signal from an S-VHS VCR or DVD player.

DVD VIDEO INPUT jacks

Connect video from a DVD player. Note: Only black and white signals are output from a monitor in DVD mode.

VHF/UHF

Connect to an antenna or to a cable TV system.

CHAPTER ONE: YOUR NEW TV 1.5

Remote Control

You can use the remote control up to about 23 feet from the TV. When using the remote, always point it directly at the TV.

You can also use your remote control to operate your VCR and cable box. See page 4.1 for details. Note: The buttons that are not described below do not function.

POWER

Turns the TV on and off.

Number buttons

Press to select channels directly on the TV.

+100

Press to select channels over 100. For example, to select channel 121, press “+100,” then press “2” and “1.”

P.SIZE

Press to change the screen size.

R.SURF

Press the R.SURF button to automatically return to a preferred channel after a user-preset time delay.

SLEEP

Press to select a preset time interval for automatic shutoff.

TURBO

Press to turn the TURBO sound On or Off.

∏

MUTE

Press to temporarily cut off the sound.

”

CH▲ and CH▼ (Channel Up/Down)

Press CH▲ or CH▼to change channels. (Also used to highlight selections on the on-screen menus.)

’

P.STD

Adjust the TV picture by selecting one of the preset factory settings (or select your personal, customized picture settings).

˝ TV

Press to use your remote control to operate your TV.

VCR

Press to use your remote control to operate your VCR.

CABLE

Press to use your remote control to operate a cable box.

SET

Use this button when you are setting up your remote control to operate your VCR or cable box.

PRE-CH

Tunes to the previous channel.



MTS (Multichannel Television Stereo)

Press to choose stereo, mono or Separate Audio Program (SAP broadcast).

DISPLAY

Press to see the time, channel, etc., on-screen. Also press to exit (quit) the menu system.

VOL -, VOL +

Press to increase or decrease the volume. (Also used to make selections on the on-screen menus.)

Displays the main on-screen menu.

TV/VIDEO

Press to display all of the available video sources (i.e., Antenna/cable, VCR).

YOUR NEW TV

For models TXL2791F/TXM3292F

1.6 CHAPTER ONE: YOUR NEW TV

YOUR NEW TV

Remote Control

VCR Controls

•

REW (Rewind)

Press to rewind a tape in your VCR.

•

STOP

Press this button to stop a tape during play, record, rewind or fast forward. If the button is pressed during Full-Automatic play, the function will be cancelled.

•

PLAY

Press the PLAY button to play back prerecorded tapes.

•

F. F

Press to fast forward the tape in your VCR.

•

PAUSE

Press to pause your VCR’s tape.

For models TXL2791F/TXM3292F

CHAPTER ONE: YOUR NEW TV 1.7

Remote Control

YOUR NEW TV

For model TXM2790F

POWER

Turns the TV on and off.

Number buttons

Press to select channels directly on the TV.

+100

Press to select channels over 100. For example, to select channel 121, press “+100,” then press “2” and “1.”

MUTE

Press to temporarily cut off the sound.

CH▲ and CH▼ (Channel Up/Down)

Press CH▲ or CH▼to change channels. (Also used to highlight selections on the on-screen menus.)

TV/VIDEO

Press to display all of the available video sources (i.e., Antenna/cable, VCR).

∏

R.SURF

Press the R.SURF button to automatically return to a preferred channel after a user-preset time delay.

”

SLEEP

Press to select a preset time interval for automatic shutoff.

’

MTS (Multichannel Television Stereo)

Press to choose stereo, mono or Separate Audio Program (SAP broadcast).

V.CHIP(Only USA)

Press to set up and activate the parental locks.

PRE-CH

Tunes to the previous channel.



DISPLAY

Press to see the time, channel, etc., on-screen. Also press to exit (quit) the menu system.

VOL -, VOL +

Press increase or decrease the volume. (Also used to make selections on the on-screen menus.)

Displays the main on-screen menu.

2.1 CHAPTER TWO: INSTALLATION

Connecting VHF and UHF Antennas

If your antenna has a set of leads that look like this, see “Antennas with 300-ohm Flat Twin Leads,” below.

If your antenna has one lead that looks like this, see “Antennas with 75-ohm Round Leads,” on page 2.2.

If you have two antennas, see “Separate VHF and UHF Antennas,” on page 2.2.

Antennas with 300-ohm Flat Twin Leads

If you are using an off-air antenna (such as a roof antenna or “rabbit ears”) that has 300-ohm twin flat leads, follow the directions below.

Chapter Two

INSTALLATION

Place the wires from the twin leads under the screws on the 300-75 ohm adaptor (not supplied). Use a screwdriver to tighten the screws.

Plug the adaptor into the VHF/UHF terminal on the bottom of the back panel.

CHAPTER TWO: INSTALLATION 2.2

Connecting Cable TV

To connect to a cable TV system, follow the instructions below.

Cable without a Cable Box

▼

Plug the incoming cable into the VHF/UHF antenna terminal on back of the TV.

Because this TV is cable-ready, you do not need a cable box to view unscrambled cable channels.

Plug the combiner into the VHF/UHF terminal on the bottom of the rear panel.

INSTALLATION

Separate VHF and UHF Antennas

If you have two separate antennas for your TV (one VHF and one UHF), you must combine the two antenna signals before connecting the antennas to the TV. This procedure requires an optional combiner-adaptor (available at most electronics shops).

Connect both antenna leads to the combiner.

Antennas with 75-ohm Round Leads

Plug the antenna lead into the VHF/UHF terminal on the bottom of the back panel.

2.3 CHAPTER TWO: INSTALLATION

INSTALLATION

Connecting to a Cable Box that Descrambles All Channels

▼

Find the cable that is connected to the ANTENNA OUT terminal on your cable box.

This terminal might be labeled “ANT OUT,” “VHF OUT,” or simply, “OUT.”

Connect the other end of this cable to the VHF/UHF antenna terminal on the back of the TV.

Connecting to a Cable Box that Descrambles Some Channels

If your cable box descrambles only some channels (such as premium channels), follow the instructions below. You will need a two-way splitter, an RF (A/B) switch, and four lengths of coaxial cable. (These items are available at most electronics stores.)

▼

Find and disconnect the cable that is connected to the ANTENNA IN terminal on your cable box.

This terminal might be labeled

“ANT IN,” “VHF IN,” or simply, “IN.”

Connect this cable to a two-way splitter.

Connect a coaxial cable between an OUTPUT terminal on the splitter and the IN terminal on the cable box.

CHAPTER TWO: INSTALLATION 2.4

Connect a coaxial cable between the ANTENNA OUT terminal on the cable box and the B–IN terminal on the A/B switch.

Connect another cable between the other OUT terminal on the splitter and the A–IN terminal on the RF (A/B) switch.

Connect the last coaxial cable between the OUT terminal on the RF (A/B) switch and the VHF/UHF terminal on the rear of the TV.

INSTALLATION

Connecting a VCR

These instructions assume that you have already connected your TV to an antenna or a cable TV system (according to the instructions on pages 2.1-2.3). Skip step 1 if you have not yet connected to an antenna or a cable system.

After you’ve made this connection, set the A/B switch to the “A” position for normal viewing. Set the A/B switch to the “B” position to view scrambled channels. (When you set the A/B switch to “B,” you will need to tune your TV to the cable box’s output channel, which is usually channel 3 or 4.)

Unplug the cable or antenna from the back of the TV.

Connect the cable or antenna to the ANTENNA INterminal on the back of the VCR.

2.5 CHAPTER TWO: INSTALLATION

INSTALLATION

Connect a coaxial cable between the ANTENNA OUT terminal on the VCR and the antenna terminal on the TV.

Connect a set of audio cables between the AUDIO OUTjacks on the VCR and the AUDIOjacks on the TV.

Connect a video cable between the VIDEO OUT jack on the VCR and the VIDEO jack on the TV.

Follow the instructions in “Viewing a VCR or Camcorder Tape” to view your VCR tape.

Note: This figure shows the Standard Connector-jack panel. The actual configuration on your TV may be different, depending on the model.

A coaxial cable is usually included with a VCR. (If not, check your local electronics store).

If you have a “mono” (non-stereo) VCR, use the Y-connector (not supplied) to hook up to the left and right audio input jacks of the TV. If your VCR is stereo, you must connect two cables.

+ 42 hidden pages