Samsung TRM-810S, TRM-410S User Manual
MOBILE VIDEO RECORDER
Quick Manual
USB 2.0
USB 3.0
AUDIO
POWER
REC
ALARM
VGA
GPS ANT
HDD1
HDD2
HDMI
CONTROL BOX
RS-232C
CONSOLE
DC 12V-36V
English
Package Contents
` The appearance of the components may differ from the image shown.
M
` Accessory category and quantity may differ depending on sales region.
TRM-1610S/1610M
AUDIO
POWER REC ALARM
GPS ANT
USB 3.0
HDMI
VGA
HDD 1
NVR Power cable
USB 2.0
USB 2.0
HDD 2
User Manual CD User Manual or Quick Manual
Wi-Fi antenna Mounting bracket Screw for bracket assembly Mounting screws
HDD fixing screws HDD lock key M12 to USB cable GPS antenna
How to install the product
` The images below are based on the TRM-1610S model.
M
1 Remove the mounting bracket and side brackets.
2 Tighten the side brackets to the body.
Screw for b racket
assembly
HDMI
AUDIO
ALARM
REC
VGA
POWER
GPS ANT
HDD1
3 Install the mounting bracket at the installation site.
4 Install the main body with the side brackets in the bracket installed in Step 3.
Mounting
screws
Screw for b racket
USB 2.0
USB 2.0
USB 3.0
HDD2
assembly
HDD handle
Control box / Control box connection
cable
Alarm cable
TRM-410S/810S/810M
HDD 1
HDD 2
POWER REC ALARM
CONSOLE
USB 2.0 USB 2.0
NVR Power cable
Wi-Fi antenna Mounting bracket Screw for bracket assembly Mounting screws
HDD fixing screws HDD lock key GPS Module Control box
VGA
HDMI
AUDIO
User Manual CD User Manual or Quick Manual
` Be sure to observe the work procedure (1 - 4) when installing the product, and pay attention to potential accidents caused by the
J
product falling.
` When moving the set, do not move it while holding the HDD handle.
How to install the control box
` The images below are based on the TRM-1610S model.
M
Assemble mounting screws and install the camera on a wall/floor/ceiling as shown in the figure.
Connect to the main unit via the control box connection cable.
Mounting
screws
1
CONSOLE
CONTROL BOX
ALARM BLOCK
WIFI ANT2 WIFI ANT1
VIEWER CAMERA
PoE1 PoE2 PoE3 PoE4
Control b ox
DC 9V~36V
RS-232C
Installing the HDD
AUDIO
REC
ALARM
` The images below are based on the TRM-1610S model.
M
TRM-1610S/TRM-1610M
1 Unscrew the HDD bracket fixing screws on the front of the set and pull it to the front to separate the HDD.
` If the lock on the front is locked, open the lock using the key that was provided when you purchased the product.
ALARM
REC
VGA
POWER
GPS ANT
HDD1
USB 2.0
USB 3.0
HDMI
HDD2
AUDIO
2 Loosen the screws on the front/rear of the bracket
and separate the bracket.
3 After replacing/installing the HDD, fix the HDD and
bracket with screws.
AUDIO
ALARM
REC
POWER
GPS ANT
HDD1
USB 2.0
USB 3.0
HDMI
HDD2
VGA
HDMI
AUDIO
ALARM
REC
VGA
POWER
GPS ANT
HDD1
TRM-810S/TRM-810M/TRM-410S
` The images below are based on the TRM-810S model.
M
1 Unscrew the HDD bracket fixing screws on the front of the set and pull it to the front to separate the HDD.
` If the lock on the front is locked, open the lock using the key that was provided when you purchased the product.
HDD 1
HDD 2
ALARM
REC
POWER
CONSOLE
USB 2.0
USB 3.0
HDD2
USB 2.0 USB 2.0
HDMI
AUDIO
VGA
HDD 1
HDD 2
ALARM
USB 2.0 USB 2.0
REC
POWER
CONSOLE
VGA
HDMI
AUDIO
2 Remove the screws from the bracket to separate the bracket.
HDD 1
HDD 2
ALARM
USB 2.0 USB 2.0
REC
POWER
CONSOLE
VGA
HDMI
AUDIO
3 After replacing/installing the HDD, fix the HDD and
bracket with screws.
4 Slide the bracket with the HDD into the main body,
and tighten the screws to fix it.
USB 2.0
USB 3.0
HDMI
HDD2
AUDIO
ALARM
REC
VGA
POWER
GPS ANT
HDD1
` If you are adding a new or previously used HDD to this product in addition to the HDD(s) originally installed, format the new HDD
J
manually in the set before use.
` For replacement or installation of an additional HDD you must contact your dealer or our customer center.
4 Slide the bracket with the HDD into the main body, and
tighten the screws to fix it.
` Make sure to properly place the fan connector when installing HDD.
J
2
HDD 1
HDD 2
ALARM
USB 2.0 USB 2.0
REC
POWER
CONSOLE
VGA
HDMI
AUDIO
Loading...