MOBILE VIDEO RECORDER
Quick Manual
English
Package Contents
MM`` The appearance of the components may differ from the image shown. `` Accessory category and quantity may differ depending on sales region.
TRM-1610S/1610M
NVR |
Power cable |
User Manual CD |
User Manual or Quick Manual |
Wi-Fi antenna |
Mounting bracket |
Screw for bracket assembly |
Mounting screws |
HDD fixing screws |
HDD lock key |
M12 to USB cable |
GPS antenna |
Control box / Control box connection |
Alarm cable |
|
cable |
||
|
TRM-410S/810S/810M
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
NVR |
Power cable |
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Wi-Fi antenna |
Mounting bracket |
HDD fixing screws |
HDD lock key |
User Manual CD
Screw for bracket assembly |
GPS Module |
User Manual or Quick Manual
Mounting screws |
Control box |
How to install the product
MM`` The images below are based on the TRM-1610S model.
1 Remove the mounting bracket and side brackets. 2 Tighten the side brackets to the body.
Screw for bracket assembly
|
Screw for bracket |
assembly |
3 Install the mounting bracket at the installation site.
4 Install the main body with the side brackets in the bracket installed in Step 3.
Mounting
screws
|
HDD handle |
JJ`` Be sure to observe the work procedure (1 - 4) when installing the product, and pay attention to potential accidents caused by the product falling.
`` When moving the set, do not move it while holding the HDD handle.
How to install the control box
MM`` The images below are based on the TRM-1610S model.
Assemble mounting screws and install the camera on a wall/floor/ceiling as shown in the figure. Connect to the main unit via the control box connection cable.
|
|
CONTROL BOX |
|
Control box |
Mounting |
|
|
|
|
screws |
|
|
|
|
|
CONSOLE |
RS-232C |
DC 9V~36V |
|
|
ALARM BLOCK |
|
|
|
|
WIFI ANT2 |
|
|
WIFI ANT1 |
|
VIEWER |
CAMERA |
PoE2 PoE3 PoE4 |
|
|
|
PoE1 |
|
1
Installing the HDD
MM`` The images below are based on the TRM-1610S model.
TRM-1610S/TRM-1610M
1 Unscrew the HDD bracket fixing screws on the front of the set and pull it to the front to separate the HDD.
`` If the lock on the front is locked, open the lock using the key that was provided when you purchased the product.
|
|
ER |
|
2 Loosen the screws on the front/rear of the bracket and separate the bracket.
3 After replacing/installing the HDD, fix the HDD and bracket with screws.
TRM-810S/TRM-810M/TRM-410S
MM`` The images below are based on the TRM-810S model.
1 Unscrew the HDD bracket fixing screws on the front of the set and pull it to the front to separate the HDD.
`` If the lock on the front is locked, open the lock using the key that was provided when you purchased the product.
|
|
2 Remove the screws from the bracket to separate the bracket.
|
|
3 After replacing/installing the HDD, fix the HDD and bracket with screws.
4 Slide the bracket with the HDD into the main body, and tighten the screws to fix it.
GPS ANT
JJ`` If you are adding a new or previously used HDD to this product in addition to the HDD(s) originally installed, format the new HDD manually in the set before use.
`` For replacement or installation of an additional HDD you must contact your dealer or our customer center.
4 Slide the bracket with the HDD into the main body, and tighten the screws to fix it.
JJ`` Make sure to properly place the fan connector when installing HDD.
2