SAMSUNG TDA8374B, TDA8374, TDA8374A, TDA8373, TDA8375 DATA SHEET

...
INTEGRATED CIRCUITS
DATA SH EET
TDA837x family
2
I
Preliminary specification File under Integrated Circuits, IC02
1997 Jul 01
Philips Semiconductors Preliminary specification
I2C-bus controlled economy PAL/NTSC and NTSC TV-processors
FEATURES
Available in all ICs:
Vision IF amplifier with high sensitivity and good figures for differential phase and gain
PLL demodulator for the IF signal
Alignment-free sound demodulator
Flexible source selection with a CVBS input for the
internal signal and Y/C or CVBS input for the external signal
Audio switch
The output signal of the CVBS (Y/C) switch is externally
available
Integrated chrominance trap and band-pass filters (auto-calibrated)
Luminance delay line integrated
A symmetrical peaking circuit in the luminance channel
Black stretching of non-standard CVBS or luminance
signals
RGB control circuit with black current stabilization and white point adjustment
Linear RGB inputs and fast blanking
Horizontal synchronization with two control loops and
alignment-free horizontal oscillator
Slow start and slow stop of the horizontal drive pulses
Vertical count-down circuit
Vertical driver optimized for DC-coupled vertical output
stages
2
C-bus control of various functions
I
Low dissipation
Small amount of peripheral components compared with
competition ICs.
TDA837x family
GENERAL DESCRIPTION
The various versions of the TDA837x series are I controlled single-chip TV processors which are intended to be applied in PAL/NTSC (TDA8374 and TDA8375) and NTSC (TDA8373 and TDA8377) television receivers. All ICs are available in an SDIP56 package and some versions are also available in a QFP64 package. The ICs are pin compatible so that with one application board NTSC and PAL/NTSC (or multistandard together with the SECAM decoder TDA8395) receivers can be built.
Functionally this IC series is split in to 2 categories:
Versions intended to be used in economy TV receivers with all basic functions
Versions with additional functions such as E-W geometry control, horizontal and vertical zoom function and YUV interface which are intended for TV receivers with 110° picture tubes.
The various type numbers are given in Table 1. The detailed differences between the various ICs are
given in Table 2.
2
C-bus
Table 1 TV receiver versions
TV RECEIVERS
ECONOMY MID/HIGH END ECONOMY MID/HIGH END
PAL only TDA8374B TDA8374BH PAL/NTSC (SECAM) TDA8374 and TDA8374A TDA8375 and TDA8375A TDA8374AH TDA8375AH NTSC TDA8373 TDA8377 and TDA8377A −−
1997 Jul 01 2
SDIP56 PACKAGE QFP64 PACKAGE
Philips Semiconductors Preliminary specification
I2C-bus controlled economy PAL/NTSC
TDA837x family
and NTSC TV-processors
Table 2 Differences between the various ICs
CIRCUITS
8373 8374 8374A(H) 8374B(H) 8375 8375A(H) 8377 8377A
Multistandard IF X −−XX −− Automatic Volume Levelling
XX − −−− −−
(AVL) PAL decoder X X XXX −− SECAM interface X X XXX −− NTSC decoder X X X X X X X X Colour matrix PAL/NTSC (Japan) X X XXX −− Colour matrix NTSC (USA/Japan) X − − −−−XX YUV interface −− − − XXXX Horizontal geometry −− − − XXXX Horizontal and vertical zoom −− − −XX XX
QUICK REFERENCE DATA
IC VERSION (TDA)
SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT
Supplies
V
P
I
P
supply voltage 8.0 V supply current 110 mA
Input voltages
V
48,49(rms)
video IF amplifiers sensitivity
70 −µV
(RMS value)
V
1(rms)
sound IF amplifiers sensitivity
1.0 mV
(RMS value)
V
2(rms)
external audio input voltage
500 mV
(RMS value)
V
11(p-p)
external CVBS/Y input voltage
1.0 V
(peak-to-peak value)
V
10(p-p)
external chrominance input voltage
0.3 V
(burst amplitude) (peak-to-peak value)
V
23-25(p-p)
RGB input voltage
0.7 V
(peak-to-peak value)
Output signals
V
6(p-p)
IF video output voltage
2.5 V
(peak-to-peak value)
I
54
V
oVSW
tuner AGC output current range 0 5mA output signal level of video switch
1.0 V
(peak-to-peak value)
V
30(p-p)
(R Y) output voltage
525 mV
(peak-to-peak value)
1997 Jul 01 3
Philips Semiconductors Preliminary specification
I2C-bus controlled economy PAL/NTSC
TDA837x family
and NTSC TV-processors
SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT
V
29(p-p)
V
28(p-p)
V
19-21(p-p)
I
40
I
46,47(p-p)
I
45(peak)
ORDERING INFORMATION
TYPE
NUMBER
TDA837xA SDIP56 plastic shrink dual in-line package; 56 leads (600 mil) SOT400-1 TDA837xH QFP64 plastic quad flat package; 64 leads (lead length 1.95 mm);
(B Y) output voltage (peak-to-peak value)
luminance output voltage (peak-to-peak value)
RGB output signal amplitudes (peak-to-peak value)
horizontal output current 10 mA vertical output current
(peak-to-peak value) E-W output current (peak value) TDA8375A,
TDA8377A, TDA8375 and TDA8377
PACKAGE
NAME DESCRIPTION VERSION
body 14 × 20 × 2.7 mm; high stand-off height
675 mV
1.4 V
2.0 V
1 mA
1.2 mA
SOT319-1
1997 Jul 01 4
Philips Semiconductors Preliminary specification
I2C-bus controlled economy PAL/NTSC and NTSC TV-processors
BLOCK DIAGRAM
18
52
51
46
50
40
OUTPUT
HORIZONTAL
2nd LOOP AND
+8 V
9 42 4154
44 12 37
AND
VCO
CONTROL
REF
47
VERTICAL
GEOMETRY
DIVIDER
VERTICAL
HORIZONTAL/
SYNC
SEPARATOR
AND 1st LOOP
TDA8373
BLACK
CURRENT
STABILIZER
BLACK
STRETCHER
SYNC
VERTICAL
SEPARATOR
22
CONTR
BRI
point
white
REF
20
19
21
AND
OUTPUT
RGB CONTROL
AND
DELAY
PEAKING
FILTER
TUNING
TDA837x family
MGK286
RGB INPUT
RGB MATRIX
AND SWITCH
3
AND
G - Y MATRIX
SAT CONTROL
BY
RY
NTSC
DECODER
24 25 26
2331
39
322930
3436336161110381713
3.6
MHz
3
SAT
ok, full pagewidth
VOL SW
SW
56
HUE
CVBS
SWITCH
PLL
DEMODULATOR
LIMITER
1
TRAP
SOUND
SOUND
BAND-PASS
Fig.1 Block diagram of bus-controlled economy NTSC TV-processor TDA8373.
43 14
8753
5
MUTE
BAND-PASS
TRAP
VIDEO
AND MUTE
AMPLIFIER
AFC
SW
MUTE
AFC
55245
15
SWITCH
CVBS Y/C
AND MUTE
PRE-AMPLIFIER
AVL AND
SWITCH AND
VOLUME CONTROL
C-BUS
2
I
TRANSCEIVER
point
tuner
take-over
AGC FOR IF
AND TUNER
ADJ
VCO
ADJUSTMENT
1 × 8 BITS
1 × 4 BITS
14 × 6 BITS
CONTROL DACs
IDENT
VIDEO
IDENTIFICATION
AND PLL
VIF AMPLIFIER
DEMODULATOR
49
48
4
3
1997 Jul 01 5
The TDA8373 is only supplied in an SDIP package.
Philips Semiconductors Preliminary specification
I2C-bus controlled economy PAL/NTSC and NTSC TV-processors
18
52
51
46
50
+8 V
40
OUTPUT
HORIZONTAL
2nd LOOP AND
9 42 41
44 12 37
AND
VCO
CONTROL
REF
47
VERTICAL
GEOMETRY
DIVIDER
VERTICAL
HORIZONTAL/
SYNC
SEPARATOR
AND 1st LOOP
TDA8374
BLACK
CURRENT
STABILIZER
BLACK
STRETCHER
SYNC
VERTICAL
SEPARATOR
CONTR
white
22
BRI
point
REF
20
19
21
AND
OUTPUT
RGB CONTROL
AND
DELAY
PEAKING
FILTER
TUNING
TDA837x family
MGK287
RGB INPUT
RGB MATRIX
AND SWITCH
3
AND
G - Y MATRIX
SAT CONTROL
BY
RY
PAL/NTSC
DECODER
(51)
24 25 26
23
39
31 322930
TDA4665
34
3.6
MHz
35
4.4
MHz
36336161110381713
3
SAT
k, full pagewidth
43 14
87
53
54
C-BUS
2
I
TRANSCEIVER
point
tuner
take-over
AGC FOR IF
AND TUNER
ADJ
VCO
ADJUSTMENT
HUE
BAND-PASS
1 × 8 BITS
1 × 4 BITS
POL
CONTROL DACs
IDENT
14 × 6 BITS
VIDEO
IDENTIFICATION
MUTE
POL
VIDEO
TRAP
AND MUTE
AMPLIFIER
SW
MUTE
SWITCH
CVBS Y/C
SW
AND MUTE
PRE-AMPLIFIER
CVBS
SWITCH
PLL
DEMODULATOR
TRAP
SOUND
Fig.2 Block diagram of bus-controlled economy PAL/NTSC TV processor TDA8374.
AFC
AND PLL
VIF AMPLIFIER
DEMODULATOR
49
48
4
3
AFC
5
15
AVL AND
55245
VOL SW
SWITCH AND
VOLUME CONTROL
56
LIMITER
1
SOUND
BAND-PASS
1997 Jul 01 6
For most pins the QFP64 pinning is not indicated.
Philips Semiconductors Preliminary specification
I2C-bus controlled economy PAL/NTSC and NTSC TV-processors
(5) 52
(63) 46
HORIZONTAL/
SYNC
1 × 8 BITS
CONTROL DACs
IDENT
VERTICAL
VIDEO
(4) 51
(64) 47
GEOMETRY
DIVIDER
VERTICAL
SEPARATOR
AND 1st LOOP
1 × 4 BITS
18 × 6 BITS
IDENTIFICATION
TDA8375
MUTE
POL
(30) 18
BLACK
BLACK
VERTICAL
VIDEO
CURRENT
STRETCHER
SYNC
BAND-PASS
TRAP
AMPLIFIER
ok, full pagewidth
(3) 50
(62) 45
E-W
GEOMETRY
40
(56)
41
(57)
42
(58)
OUTPUT
HORIZONTAL
2nd LOOP AND
37
(53)
12
+8 V
9
44
14
43
8
7
53
54
(22,23)
(19)
(60,61)
(25,26)
(59)
(18)
(17)
(6)
(7)
AND
VCO
CONTROL
C-BUS
2
I
TRANSCEIVER
point
tuner
take-over
AGC FOR IF
AND TUNER
ADJ
REF
POL
(34) 22
CONTR
STABILIZER
BRI
point
white
SEPARATOR
AND MUTE
AFC
(33) 21
REF
SW
MUTE
(32) 20
(31) 19
AND
OUTPUT
RGB CONTROL
CORING
DELAY PLUS
PEAKING PLUS
FILTER
TUNING
SWITCH
CVBS Y/C
AND MUTE
PRE-AMPLIFIER
TDA837x family
MGK288
(38)
26
(37)
25
(36)
RGB INPUT
AND SWITCH
3
AND
SAT CONTROL
RY
PAL/NTSC
DECODER
CVBS
SWITCH
PLL
DEMODULATOR
(35)
(55) (39) (40)
(47)
(48)
(45)
(46)
(50)
(51)
(52)
(49) (28) (21) (20)
(54)
(29)
(24)
(16)
24
23
39 27 28
31
32
29
30
34
35
36
33 16 11 10
38
17
13
6
TDA4665
3.6
MHz
4.4
MHz
TRAP
SOUND
Fig.3 Block diagram of bus-controlled economy PAL/NTSC TV processor TDA8375.
3
RGB MATRIX
SAT
G - Y MATRIX
BY
HUE
SW
5 (15)
AFC
15 (27)
VCO
ADJUSTMENT
3 (13)
4 (14)
48 (1)
AND PLL
VIF AMPLIFIER
DEMODULATOR
49 (2)
1997 Jul 01 7
55 (8)
VOL SW
SWITCH AND
VOLUME CONTROL
2 (11)
56 (9)
LIMITER
1 (10)
SOUND
BAND-PASS
Philips Semiconductors Preliminary specification
I2C-bus controlled economy PAL/NTSC and NTSC TV-processors
18
52
51
46
50
45
E-W
GEOMETRY
47
VERTICAL
GEOMETRY
BLACK
TDA8377
OUTPUT
HORIZONTAL
2nd LOOP AND
+8 V
9 42 41 40
44 12 37
AND
VCO
CONTROL
REF
DIVIDER
VERTICAL
HORIZONTAL/
SYNC
SEPARATOR
AND 1st LOOP
CURRENT
STABILIZER
BLACK
STRETCHER
SYNC
VERTICAL
SEPARATOR
22
CONTR
BRI
point
white
21
20
RGB CONTROL
DELAY PLUS
REF
19
AND
OUTPUT
CORING
PEAKING PLUS
FILTER
TUNING
TDA837x family
MGK289
RGB INPUT
RGB MATRIX
AND SWITCH
3
AND
G - Y MATRIX
SAT CONTROL
BY
RY
NTSC
DECODER
24 25 26
23
39
28 27
31 322930
3436336161110381713
3.6
MHz
3
SAT
ull pagewidth
43 14
87
53
54
C-BUS
2
I
TRANSCEIVER
point
tuner
take-over
AGC FOR IF
AND TUNER
ADJ
VCO
ADJUSTMENT
HUE
MUTE
BAND-PASS
TRAP
VIDEO
AND MUTE
AMPLIFIER
SW
MUTE
SWITCH
CVBS Y/C
SW
AND MUTE
PRE-AMPLIFIER
CVBS
PLL
SWITCH
DEMODULATOR
TRAP
SOUND
1 × 8 BITS
CONTROL DACs
IDENT
18 × 6 BITS
VIDEO
IDENTIFICATION
1 × 4 BITS
Fig.4 Block diagram of bus-controlled economy NTSC TV processor TDA8377.
AFC
AND PLL
VIF AMPLIFIER
DEMODULATOR
49
48
4
3
AFC
5
55215
VOL SW
SWITCH AND
VOLUME CONTROL
56
LIMITER
1
SOUND
BAND-PASS
1997 Jul 01 8
The TDA8377 is only supplied in an SDIP package.
Philips Semiconductors Preliminary specification
I2C-bus controlled economy PAL/NTSC and NTSC TV-processors
PINNING
(2)
(1)
(1)
PIN
DESCRIPTION
2
C-bus)
2
C-bus)
39 luminance input
49 SECAM reference output
51 4.43 MHz crystal connection
SYMBOL
SDIP56 QFP64
SIF 1 10 sound IF input AUDI 2 11 external audio input VCO1 3 13 IF VCO 1 tuned circuit VCO2 4 14 IF VCO 2 tuned circuit PLL 5 15 PLL loop filter IFVO 6 16 IF video output SCL 7 17 serial clock input (I SDA 8 18 serial data input/output (I DEC
BG
9 19 band gap decoupling CHROMA 10 20 chrominance input CVBS/Y 11 21 CVBS/Y input V
P1
CVBS
int
12 22 and 23 main supply voltage (+8 V)
13 24 internal CVBS input GND1 14 25 and 26 ground AUDO 15 27 audio output DEC CVBS
FT
ext
16 28 decoupling filter tuning
17 29 external CVBS input BLKIN 18 30 black current input BO 19 31 blue output GO 20 32 green output RO 21 33 red output BCLIN 22 34 beam current input RI 23 35 red input GI 24 36 green input BI 25 37 blue input RGBIN 26 38 RGB insertion input YIN 27 YOUT 28 40 luminance output BYO 29 45 (B Y) output RYO 30 46 (R Y) output RYI 31 47 (R Y) input BYI 32 48 (B Y) input SEC
ref
33 XTAL1 34 50 3.58 MHz crystal connection XTAL2 35 LFBP 36 52 loop filter burst phase detector V
P2
37 53 horizontal oscillator supply voltage (+8 V)
CVBSO 38 54 CVBS output
TDA837x family
1997 Jul 01 9
Philips Semiconductors Preliminary specification
I2C-bus controlled economy PAL/NTSC and NTSC TV-processors
(2)
PIN
DESCRIPTION
62 east-west drive output
SYMBOL
BLPH 39 55 black peak hold capacitor HOUT 40 56 horizontal drive output FBI/SCO 41 57 flyback input and sandcastle output PH2 42 58 phase 2 filter/protection PH1 43 59 phase 1 filter GND2 44 60 and 61 ground 2 EWD 45 VDOB 46 63 vertical drive output B VDOA 47 64 vertical drive output A IFIN1 48 1 IF input 1 IFIN2 49 2 IF input 2 EHT/PRO 50 3 EHT/overvoltage protection input VSAW 51 4 vertical sawtooth capacitor I
ref
DEC
AGC
AGCOUT 54 7 tuner AGC output AUDEEM 55 8 audio deemphasis DEC 56 9 decoupling sound demodulator i.c. 12 internally connected i.c. 41 internally connected i.c. 42 internally connected i.c. 43 internally connected i.c. 44 internally connected
SDIP56 QFP64
52 5 reference current input 53 6 AGC decoupling capacitor
TDA837x family
Notes
1. In the TDA8373 and TDA8377 pin 35 (4.43 MHz crystal) is internally connected and pin 33 is just a subcarrier output which can be used as a reference signal for comb filter ICs.
2. In the TDA8373 and TDA8374 the following pins are different (SDIP56): Pin 27: not connected; Pin 45: AVL capacitor.
1997 Jul 01 10
Philips Semiconductors Preliminary specification
I2C-bus controlled economy PAL/NTSC and NTSC TV-processors
handbook, halfpage
SIF
AUDI VCO1 VCO2
PLL
IFVO
SCL SDA
DEC
BG
CHROMA
CVBS/Y
V
P1
CVBS
GND1
AUDO
DEC
FT
CVBS
ext
BLKIN
BO GO RO
BCLIN
RGBIN
YIN
YOUT
1 2 3 4 5 6 7 8
9 10 11 12 13
int
14
TDA837x
15 16 17 18 19 20 21 22
RI
23
GI
24
BI
25 26 27 28
MGK284
56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29
DEC AUDEEM AGCOUT DEC
AGC
I
ref
VSAW EHT/PRO IFIN2 IFIN1 VDOA VDOB EWD GND2 PH1 PH2 FBI/SCO HOUT BLPH CVBSO V
P2
LFBP XTAL2 XTAL1 SEC
ref
BYI RYI RYO BYO
TDA837x family
Fig.5 Pin configuration (SDIP56).
1997 Jul 01 11
Philips Semiconductors Preliminary specification
I2C-bus controlled economy PAL/NTSC and NTSC TV-processors
handbook, full pagewidth
VDOA
VDOB
EWD
GND2
GND2
PH1
PH2
64
63
62
61
60
59
58
1
IFIN1
2
IFIN2
EHT/PRO
DEC AGCOUT AUDEEM
3 4
VSAW
5
I
ref
6
AGC
7 8
DEC
9
SIF
10
AUDI
11
i.c.
12
VCO1
13
VCO2
14
PLL
15
IFVO 33
16
TDA837xH
FBI/SCO
HOUT
57
56
BLPH 55
CVBSO
VP2LFBP
54
53
TDA837x family
ref
XTAL2
XTAL1
SEC
52
51
50
48
BYI RYI
47
RYO
46
BYO
45
i.c.
44
i.c.
43
i.c.
42
i.c.
41
YOUT
40
YIN
39
RGBIN
38
BI
37
GI
36
RI
35
BCLIN
34
RO
17
SCL
18
SDA
19
BG
DEC
20
CHROMA
22
VP1V
CVBS/Y
23
24
int
P1
CVBS
21
Fig.6 Pin configuration (QFP64).
1997 Jul 01 12
25
GND1
26
GND1
27
AUDO
28
FT
DEC
29
ext
CVBS
30
BLKIN
31 BO
32
MGK285
GO 49
Philips Semiconductors Preliminary specification
I2C-bus controlled economy PAL/NTSC and NTSC TV-processors
FUNCTIONAL DESCRIPTION Vision IF amplifier
The IF amplifier contains 3 AC-coupled control stages with a total gain control range which is higher than 66 dB. The sensitivity of the circuit is comparable with that of modern IF-ICs.
The video signal is demodulated by a PLL carrier regenerator. This circuit contains a frequency detector and a phase detector. During acquisition the frequency detector will tune the VCO to the correct frequency. The initial adjustment of the oscillator is realized via the
2
I
C-bus.
The switching, between SECAM L and L’, can also be realized via the I2C-bus. After lock-in the phase detector controls the VCO so that a stable phase relationship between the VCO and the input signal is achieved. The VCO operates at twice the IF frequency. The reference signal for the demodulator is obtained by using a frequency divider circuit.
The AFC output is obtained by using the VCO control voltage of the PLL and can be read via the I2C-bus. For fast search tuning systems the window of the AFC can be increased by a factor of 3. The setting is realized with the AFW bit.
Depending on the device type the AGC detector operates on top-sync level (single standard versions) or on top-sync and top-white level (multistandard versions). The demodulation polarity is switched via the I2C-bus. The AGC detector time constant capacitor is connected externally. This is mainly because of the flexibility of the application. The time constant of the AGC system during positive modulation is rather long, this is to avoid visible variations of the signal amplitude. To improve the speed of the AGC system, a circuit has been included which detects whether the AGC detector is activated every frame period. When, during 3 frame periods, no action is detected the speed of the system is increased. For signals without peak-white information the system switches automatically
TDA837x family
to a gated black level AGC. Because a black level clamp pulse is required for this method of operation the circuit will only switch to black level AGC in the internal mode.
The circuits contain a second fast video identification circuit which is independent of the synchronization identification circuit. Consequently, search tuning is also possible when the display section of the receiver is used as a monitor. However, this identification circuit cannot be made as sensitive as the slower sync identification circuit (SL) and it is recommended to use both identification outputs to obtain a reliable search system. The identification output is applied to the tuning system via
2
the I
C-bus.
The input of the identification circuit is connected to pin 13, the internal CVBS input (see Fig.1). This has the advantage that the identification circuit can also be made operative when a scrambled signal is received [descrambler connected between the IF video output (pin 6) and pin 13]. A second advantage is that the identification circuit can be used when the IF amplifier is not used (e.g. with built-in satellite tuners).
The video identification circuit can also be used to identify the selected CBVS or Y/C signal. The switching between the two modes can be realized with bit VIM.
Video switches
The circuit has two CVBS inputs (CVBS and a Y/C input. When the Y/C input is not required pin 11 can be used as the third CVBS input. The switch configuration is illustrated in Fig.7. The selection of the various sources is made via the I2C-bus.
The output signal of the CVBS switch is externally available and can be used to drive the teletext decoder, the SECAM add-on decoder and a comb filter. In applications with comb filters a Y/C input is only possible when additional switches are added. In applications without comb filters the Y/C input signal can be switched to the CVBS output.
and CVBS
int
ext
)
1997 Jul 01 13
Philips Semiconductors Preliminary specification
I2C-bus controlled economy PAL/NTSC and NTSC TV-processors
handbook, full pagewidth
IDENT
VIM
VIDEO
IDENTIFICATION
S0
S0 S5
TDA837x
13
CVBS
int
CVBS
S1
S1 S6 S2
17
ext
11
CVBS/Y
S3 S7 S4
CHROMA CVBSO
TDA837x family
to luminance/ sync processing
to chrominance processing
+
S8
10 38
MGK301
Fig.7 Configuration CVBS switch and interfacing of video identification.
Sound circuit
The sound band-pass and trap filters have to be connected externally. The filtered intercarrier signal is fed to a limiter circuit and is demodulated by a PLL demodulator. This PLL circuit automatically tunes to the incoming carrier signal, hence no adjustment is required.
The volume is controlled via the I2C-bus. The de-emphasis capacitor has to be connected externally. The non-controlled audio signal can be obtained from this pin (pin 55) (via a buffer stage).
2
The FM demodulator can be muted via the I
C-bus. This function can be used to switch-off the sound during a channel change so that high output peaks are prevented (also on the de-emphasis output).
The TDA8373 and TDA8374 contain an Automatic Volume Levelling (AVL) circuit which automatically stabilizes the audio output signal to a certain level which can be set by the user via the volume control. This function prevents big audio output fluctuations due to variations of the modulation depth of the transmitter. The AVL function can be activated via the I2C-bus.
Synchronization circuit
The sync separator is preceded by a controlled amplifier which adjusts the sync pulse amplitude to a fixed level. These pulses are fed to the slicing stage which operates at 50% of the amplitude.
The separated sync pulses are fed to the first phase detector and to the coincidence detector. The coincidence detector is used to detect whether the line oscillator is synchronized and can also be used for transmitter identification. The circuit can be made less sensitive by using the STM bit. This mode can be used during search tuning to ensure that the tuning system will not stop at very weak input signals. The first PLL has a very high static steepness so that the phase of the picture is independent of the line frequency.
The line oscillator operates at twice the line frequency. The oscillator capacitor is internal. Because of the spread of internal components an automatic calibration circuit has been added to the IC. The circuit compares the oscillator frequency with that of the crystal oscillator in the colour decoder.
1997 Jul 01 14
Philips Semiconductors Preliminary specification
I2C-bus controlled economy PAL/NTSC and NTSC TV-processors
This results in a free-running frequency which deviates less than 2% from the typical value. When the IC is switched on the horizontal output signal is suppressed and the oscillator is calibrated as soon as all subaddress bytes have been sent. When the frequency of the oscillator is correct the horizontal drive signal is switched on. To obtain a smooth switching on and switching off behaviour of the horizontal output stage the horizontal output frequency is doubled during switch-on and switch-off (slow start/stop). During that time the duty cycle of the output pulse has such a value that maximum safety is obtained for the output stage.
To protect the horizontal output transistor, the horizontal drive is immediately switched off (via the slow stop procedure) when a power-on reset is detected. The drive signal is switched on again when the normal switch-on procedure is followed, i.e. all subaddress bytes must be sent and, after calibration, the horizontal drive signal will be released again via the slow start procedure.
When the coincidence detector indicates an out-of-lock situation the calibration procedure is repeated.
TDA837x family
For this reason this protection input can be used as ‘flash protection’.
The drive pulses for the vertical sawtooth generator are obtained from a vertical countdown circuit. This countdown circuit has various windows depending on the incoming signal (50 or 60 Hz and standard or non-standard). The countdown circuit can be forced in various modes via the I2C-bus. To obtain short switching times of the countdown circuit during a channel change the divider can be forced in the search window using the NCIN bit.
The vertical deflection can be set in the de-interlace mode via the I2C-bus.
To avoid damage of the picture tube when the vertical deflection fails, the guard output current of the TDA8350 and TDA8351 can be supplied to the beam current limiting input. When a failure is detected the RGB outputs are blanked and a bit is set (NDF) in the status byte of the I2C-bus. When no vertical deflection output stage is connected this guard circuit will also blank the output signals. This can be overruled using the EVG bit.
The circuit has a second control loop to generate the drive pulses for the horizontal driver stage. The horizontal output is gated with the flyback pulse so that the horizontal output transistor cannot be switched on during the flyback time.
Adjustments can be made to the horizontal shift, vertical shift, vertical slope, vertical amplitude and the S-correction via the I2C-bus. In the TDA8375A, TDA8377A, TDA8375 and TDA8377 the E-W drive can also be adjusted via the I2C-bus. The TDA8375 and TDA8377 have a flexible zoom adjustment possibility for the vertical and horizontal deflection. When the horizontal scan is reduced to display 4 : 3 pictures on a 16 : 9 picture tube an accurate video blanking can be switched on to obtain well defined edges on the screen. The geometry processor has a differential output for the vertical drive signal and a single-ended output for the E-W drive (TDA8375A, TDA8377A, TDA8375 and TDA8377). Overvoltage conditions (X-ray protection) can be detected via the EHT tracking pin. When an overvoltage condition is detected the horizontal output drive signal will be switched off via the slow stop procedure. However, it is also possible that the drive is not switched off and that just a protection indication is given in the I2C-bus output byte. The choice is made via the input bit PRD. The ICs have a second protection input on the phase-2 filter capacitor pin. When this input is activated the drive signal is switched off immediately (without slow stop) and switched on again via the slow start procedure.
Chrominance and luminance processing
The circuit contains a chrominance band-pass and trap circuit. The filters are realized by using gyrator circuits. They are automatically calibrated by comparing the tuning frequency with the crystal frequency of the decoder. The luminance delay line and the delay for the peaking circuit are also realized by using gyrator circuits. The centre frequency of the chrominance band-pass filter is 10% higher than the subcarrier frequency. This compensates for the high frequency attenuation of the IF saw filter. During SECAM reception the centre frequency of the chrominance trap is reduced to obtain a better suppression of the SECAM carrier frequencies. All ICs have a black stretcher circuit which corrects the black level for incoming video signals which have a deviation between the black level and the blanking level (back porch).
The TDA8375A, TDA8377A, TDA8375 and TDA8377 have a defeatable coring function in the peaking circuit.
Some of the ICs have a YUV interface so that picture improvement ICs such as the TDA9170 (contrast improvement), TDA9177 (sharpness improvement) and TDA4556 and TDA4566 (CTI) can be applied. When the TDA4556 or TDA4566 is applied it is possible to increase the gain of the luminance channel by using the GAI bit in subaddress 03 so that the resulting RGB output signals will not be affected.
1997 Jul 01 15
Philips Semiconductors Preliminary specification
I2C-bus controlled economy PAL/NTSC and NTSC TV-processors
Colour decoder
Depending on the IC type the colour decoder can decode NTSC signals (TDA8373 and TDA8377) or PAL/NTSC signals (TDA8374 and TDA8375). The circuit contains an alignment-free crystal oscillator, a killer circuit and two colour difference demodulators. The 90° phase shift for the reference signal is made internally.
The TDA8373 and TDA8377 contain an Automatic Colour Limiting (ACL) circuit which prevents over saturation occurring when signals with a high chroma-to-burst ratio are received. This ACL function is also available in the TDA8374 and TDA8375, however, it is only active during the reception of NTSC signals.
The TDA8373 and TDA8377 have a switchable colour difference matrix (via the I reproduction can be adapted to the market requirements.
In the TDA8374 and TDA8375 the colour difference matrix switches automatically between PAL and NTSC, however, it is also possible to fix the matrix in the PAL standard.
The TDA8374 and TDA8375 can operate in conjunction with the SECAM decoder TDA8395 so that an automatic multistandard decoder can be realized. The subcarrier reference output for the SECAM decoder can also be used as a reference signal for a comb filter. Consequently, the reference signal is continuously available when PAL or NTSC signals are detected and only present during the vertical retrace period when a SECAM signal is detected.
Which standard the TDA8374 and TDA8375 can decode depends on the external crystals. The crystal to be connected to pin 34 must have a frequency of 3.5 MHz (NTSC-M, PAL-M or PAL-N). Pin 35 can handle crystals with a frequency of 4.4 and 3.5 MHz. Because the crystal frequency is used to tune the line oscillator, the value of the crystal frequency must be communicated to the IC via the I2C-bus. It is also possible to use the IC in the so called ‘3-norma’ mode for South America. In that event one crystal must be connected to pin 35 and the other two to pin 34. Switching between the 2 latter crystals must be performed externally. Consequently, the search loop of the decoder must be controlled by the microcontroller. To prevent calibration problems of the horizontal oscillator the external switching between the two crystals should be performed when the oscillator is forced to pin 35.
2
C-bus) so that the colour
TDA837x family
For a reliable calibration of the horizontal oscillator it is very important that the crystal indication bits (XA and XB) are not corrupted. For this reason the crystal bits can be read in the output bytes so that the software can check the
2
C-bus transmission.
I
RGB output circuit and black current stabilization
The colour difference signals are matrixed with the luminance signal to obtain the RGB signals. Linear amplifiers have been chosen for the RGB inputs so that the circuit is suited for signals that are input from the SCART connector. The insertion blanking can be switched on or off using the IE1 bit. To ascertain whether the insertion pin has a (continuous) HIGH level or not can be read via the IN1 bit. The contrast and brightness control operate on internal and external signals.
The output signal has an amplitude of approximately 2 V (black-to-white) at nominal input signals and nominal settings of the controls. To increase the flexibility of the IC it is possible to add OSD and/or teletext signals directly at the RGB outputs. This insertion mode is controlled via the insertion input. The action to switch the RGB outputs to black has some delay which must be compensated for externally.
The black current stabilization is realized by using a feedback from the video output amplifiers to the RGB control circuit. The black current of the 3 guns of the picture tube is internally measured and stabilized. The black level control is active during 4 lines at the end of the vertical blanking. The vertical blanking is adapted to the incoming CVBS signal (50 or 60 Hz). When the flyback time of the vertical output stage is longer than the 60 Hz blanking time, or when additional lines need to be blanked (e.g. for close captioning lines) the blanking can be increased to the same value as that of the 50 Hz blanking. This can be set using the LBM bit. The leakage current is measured during the first line and, during the following 3 lines, the 3 guns are adjusted to the required level. The maximum acceptable leakage current is ±100 µA. The nominal value of the black current is 10 µA. The ratio of the currents for the various guns automatically tracks with the white point adjustment so that the background colour is the same as the adjusted white point.
1997 Jul 01 16
Philips Semiconductors Preliminary specification
I2C-bus controlled economy PAL/NTSC
TDA837x family
and NTSC TV-processors
The input impedance of the black current measuring pin is 14 k. To prevent the voltage on this pin exceeding the supply voltage during scan an internal protection diode has been included.
When the TV receiver is switched on the black current stabilization circuit is not active, the RGB outputs are blanked and the beam current limiting input pin is short-circuited. Only during the measuring lines will the outputs supply a voltage of 4.2 V to the video output stage
2
C-bus specification
I Table 3 Slave address (8A)
A6 A5 A4 A3 A2 A1 A0 R/W
1000101I/O
The slave address is identical for all types. The subaddresses of the various types are slightly different. The list of subaddresses for each type is given in Tables 4, 6, 8 and 10.
TART-UP PROCEDURE
S
to ascertain whether the picture tube is warming up. As soon as the current supplied to the measuring input exceeds a value of 190 µA the stabilization circuit will be activated. After a waiting time of approximately 0.8 s the blanking and beam current limiting input pins are released. The remaining switch-on behaviour of the picture is determined by the external time constant of the beam current limiting network.
on when the oscillator is calibrated. Each time before the data in the IC is refreshed, the status bytes must be read. If POR = 1, then the procedure given above must be carried out to restart the IC. When this procedure is not followed the horizontal frequency in the TDA8374 and TDA8375 may be incorrect after power-up or a power dip.
Read the status bytes until POR = 0 and send all subaddress bytes. The horizontal output signal is switched
1997 Jul 01 17
Philips Semiconductors Preliminary specification
I2C-bus controlled economy PAL/NTSC
TDA837x family
and NTSC TV-processors
TDA8373
Valid subaddresses: 00 to 16 (subaddresses 04 to 07 are not used), subaddress FE is reserved for test purposes. Auto-increment mode available for subaddresses.
Table 4 Inputs
FUNCTION
Control 0 00 INA INB INC 0 FOA FOB 0 0 Control 1 01 0 0 DL STB POC 0 1 1 Hue 02 AVL AKB A5 A4 A3 A2 A1 A0 Horizontal Shift (HS) 03 VIM GAI A5 A4 A3 A2 A1 A0 Vertical Slope (VS) 08 NCIN STM A5 A4 A3 A2 A1 A0 Vertical Amplitude (VA) 09 VID LBM A5 A4 A3 A2 A1 A0 S-Correction (SC) 0A 0 EVG A5 A4 A3 A2 A1 A0 Vertical shift (VSH) 0B SBL PRD A5 A4 A3 A2 A1 A0 White point R 0C 0 0 A5 A4 A3 A2 A1 A0 White point G 0D 0 0 A5 A4 A3 A2 A1 A0 White point B 0E MAT 0 A5 A4 A3 A2 A1 A0 Peaking 0F 0000A3A2A1A0 Brightness 10 RBL 0 A5 A4 A3 A2 A1 A0 Saturation 11 IE1 0 A5 A4 A3 A2 A1 A0 Contrast 12 AFW IFS A5 A4 A3 A2 A1 A0 AGC takeover 13 0 VSW A5 A4 A3 A2 A1 A0 Volume control 14 SM FAV A5 A4 A3 A2 A1 A0 Adjustment IF-PLL 15 L’FA A6 A5 A4 A3 A2 A1 A0 Spare 16 00000000
SUB
ADDRESS
D7 D6 D5 D4 D3 D2 D1 D0
DATA BYTE
Table 5 Output status bytes (note 1)
OUTPUT ADDRESS D7 D6 D5 D4 D3 D2 D1 D0
00 POR X X SL XPR CD2 CD1 CD0 01 NDF IN1 X IFI AFA AFB SXA SXB 02 X X X IVW X ID2 ID1 ID0
Note
1. X = don’t care.
1997 Jul 01 18
Philips Semiconductors Preliminary specification
I2C-bus controlled economy PAL/NTSC
TDA837x family
and NTSC TV-processors
TDA8374, TDA8374AH and TDA8374BH
Valid subaddresses: 00 to 16 (subaddresses 04 to 07 are not used), subaddress FE is reserved for test purposes. Auto-increment mode available for subaddresses.
Table 6 Inputs (notes 1 and 2)
FUNCTION
Control 0 00 INA INB INC 0 FOA FOB XA XB Control 1 01 FORF FORS DL STB POC CM2 CM1 CM0 Hue 02 AVL AKB A5 A4 A3 A2 A1 A0 Horizontal Shift (HS) 03 VIM GAI A5 A4 A3 A2 A1 A0 Vertical Slope (VS) 08 NCIN STM A5 A4 A3 A2 A1 A0 Vertical Amplitude (VA) 09 VID LBM A5 A4 A3 A2 A1 A0 S-Correction (SC) 0A 0 EVG A5 A4 A3 A2 A1 A0 Vertical shift (VSH) 0B SBL PRD A5 A4 A3 A2 A1 A0 White point R 0C 0 0 A5 A4 A3 A2 A1 A0 White point G 0D 0 0 A5 A4 A3 A2 A1 A0 White point B 0E MAT 0 A5 A4 A3 A2 A1 A0 Peaking 0F 0000A3A2A1A0 Brightness 10 RBL 0 A5 A4 A3 A2 A1 A0 Saturation 11 IE1 0 A5 A4 A3 A2 A1 A0 Contrast 12 AFW IFS A5 A4 A3 A2 A1 A0 AGC takeover 13 MOD VSW A5 A4 A3 A2 A1 A0 Volume control 14 SM FAV A5 A4 A3 A2 A1 A0 Adjustment IF-PLL 15 L’FA A6 A5 A4 A3 A2 A1 A0 Spare 16 00000000
SUB
ADDRESS
D7 D6 D5 D4 D3 D2 D1 D0
DATA BYTE
Notes
1. The AVL and MOD bit are not available in the TDA8374A.
2. In the TDA8374B the AVL and MOD bit is also missing and the CM0 to CM2 and CD0 to CD2 bits have less
possibilities because this IC can only decode PAL or PAL/SECAM signals (when the TDA8395 is applied).
Table 7 Output status bytes (note 1)
OUTPUT ADDRESS D7 D6 D5 D4 D3 D2 D1 D0
00 POR FSI X SL XPR CD2 CD1 CD0 01 NDF IN1 X IFI AFA AFB SXA SXB 02 X X X IVW X ID2 ID1 ID0
Note
1. X = don’t care.
1997 Jul 01 19
Philips Semiconductors Preliminary specification
I2C-bus controlled economy PAL/NTSC
TDA837x family
and NTSC TV-processors
TDA8375 and TDA8375AH
Valid subaddresses: 00 to 16, subaddress FE is reserved for test purposes. Auto-increment mode available for subaddresses.
Table 8 Inputs
FUNCTION
Control 0 00 INA INB INC 0 FOA FOB XA XB Control 1 01 FORF FORS DL STB POC CM2 CM1 CM0 Hue 02 HBL AKB A5 A4 A3 A2 A1 A0 Horizontal Shift (HS) 03 VIM GAI A5 A4 A3 A2 A1 A0 E-W width (EW) 04 0 0 A5 A4 A3 A2 A1 A0 E-W Parabola/Width (PW) 05 0 0 A5 A4 A3 A2 A1 A0 E-W Corner Parabola (CP) 06 0 0 A5 A4 A3 A2 A1 A0 E-W trapezium (TC) 07 0 0 A5 A4 A3 A2 A1 A0 Vertical Slope (VS) 08 NCIN STM A5 A4 A3 A2 A1 A0 Vertical Amplitude (VA) 09 VID LBM A5 A4 A3 A2 A1 A0 S-Correction (SC) 0A HCO EVG A5 A4 A3 A2 A1 A0 Vertical shift (VSH) 0B SBL PRD A5 A4 A3 A2 A1 A0 White point R 0C 0 0 A5 A4 A3 A2 A1 A0 White point G 0D 0 0 A5 A4 A3 A2 A1 A0 White point B 0E MAT 0 A5 A4 A3 A2 A1 A0 Peaking 0F 0000A3A2A1A0 Brightness 10 RBL COR A5 A4 A3 A2 A1 A0 Saturation 11 IE1 0 A5 A4 A3 A2 A1 A0 Contrast 12 AFW IFS A5 A4 A3 A2 A1 A0 AGC takeover 13 MOD VSW A5 A4 A3 A2 A1 A0 Volume control 14 SM FAV A5 A4 A3 A2 A1 A0 Adjustment IF-PLL 15 L’FA A6 A5 A4 A3 A2 A1 A0 Vertical zoom (VX)
(1)
SUB
ADDRESS
16 0 0 A5 A4 A3 A2 A1 A0
D7 D6 D5 D4 D3 D2 D1 D0
DATA BYTE
Note
1. The vertical zoom byte and the HBL bit are active only in the TDA8375.
Table 9 Output status bytes (note 1)
OUTPUT ADDRESS D7 D6 D5 D4 D3 D2 D1 D0
00 POR FSI X SL XPR CD2 CD1 CD0 01 NDF IN1 X IFI AFA AFB SXA SXB 02 X X X IVW X ID2 ID1 ID0
Note
1. X = don’t care.
1997 Jul 01 20
Philips Semiconductors Preliminary specification
I2C-bus controlled economy PAL/NTSC
TDA837x family
and NTSC TV-processors
TDA8377 and TDA8377A
Valid subaddresses: 00 to 16, subaddress FE is reserved for test purposes. Auto-increment mode available for subaddresses.
Table 10 Inputs
FUNCTION
Control 0 00 INA INB INC 0 FOA FOB 0 1 Control 1 01 0 0 DL STB POC 0 1 1 Hue 02 HBL AKB A5 A4 A3 A2 A1 A0 Horizontal Shift (HS) 03 VIM GAI A5 A4 A3 A2 A1 A0 E-W width (EW) 04 0 0 A5 A4 A3 A2 A1 A0 E-W Parabola/Width (PW) 05 0 0 A5 A4 A3 A2 A1 A0 E-W Corner Parabola (CP) 06 0 0 A5 A4 A3 A2 A1 A0 E-W trapezium (TC) 07 0 0 A5 A4 A3 A2 A1 A0 Vertical Slope (VS) 08 NCIN STM A5 A4 A3 A2 A1 A0 Vertical Amplitude (VA) 09 VID 0 A5 A4 A3 A2 A1 A0 S-Correction (SC) 0A HCO EVG A5 A4 A3 A2 A1 A0 Vertical shift (VSH) 0B SBL PRD A5 A4 A3 A2 A1 A0 White point R 0C 0 0 A5 A4 A3 A2 A1 A0 White point G 0D 0 0 A5 A4 A3 A2 A1 A0 White point B 0E MAT 0 A5 A4 A3 A2 A1 A0 Peaking 0F 0000A3A2A1A0 Brightness 10 RBL COR A5 A4 A3 A2 A1 A0 Saturation 11 IE1 0 A5 A4 A3 A2 A1 A0 Contrast 12 AFW IFS A5 A4 A3 A2 A1 A0 AGC takeover 13 0 VSW A5 A4 A3 A2 A1 A0 Volume control 14 SM FAV A5 A4 A3 A2 A1 A0 Adjustment IF-PLL 15 L’FA A6 A5 A4 A3 A2 A1 A0 Vertical zoom (VX)
(1)
SUB
ADDRESS
16 0 0 A5 A4 A3 A2 A1 A0
D7 D6 D5 D4 D3 D2 D1 D0
DATA BYTE
Note
1. The vertical zoom byte and the HBL bit are active only in the TDA8377.
Table 11 Output status bytes (note 1)
OUTPUT ADDRESS D7 D6 D5 D4 D3 D2 D1 D0
00 POR X X SL XPR CD2 CD1 CD0 01 NDF IN1 X IFI AFA AFB SXA SXB 02 X X X IVW X ID2 ID1 ID0
Note
1. X = don’t care.
1997 Jul 01 21
Philips Semiconductors Preliminary specification
I2C-bus controlled economy PAL/NTSC
TDA837x family
and NTSC TV-processors
INPUT CONTROL BITS
Table 12 Source select
INA INB INC
0 0 0 internal CVBS plus audio internal CVBS 0 0 1 external CVBS plus audio external CVBS 0 1 0 Y/C plus external audio Y/C (Y plus C) 0 1 1 CVBS3 plus external audio CVBS3 1 0 0 Y/C plus internal audio internal CVBS 1 1 0 Y/C plus external audio external CVBS
Table 13 Phase 1 (ϕ-1) time constant
FOA FOB MODE
0 0 normal 0 1 slow and gated 1 0 slow/fast and gated 1 1 fast
SELECTED SIGNALS
(DECODER AND AUDIO)
SWITCH OUTPUT
Table 14 Crystal indication
XA XB CRYSTAL
0 0 two 3.6 MHz crystals 0 1 one 3.6 MHz crystal (pin 34) 1 0 one 4.4 MHz crystal (pin 35) 1 1 3.6 MHz and 4.4 MHz crystals (pins 34 and 35)
Table 15 Forced field frequency TDA8374 and TDA8375
FORF FORS FIELD FREQUENCY
0 0 auto (60 Hz when line not synchronized) 0 1 60 Hz; note 1 1 0 keep last detected field frequency 1 1 auto (50 Hz when line not synchronized)
Note
1. When switched to this mode while locked to a 50 Hz signal, the divider will only switch to forced 60 Hz when an
out-of-sync is detected in the horizontal PLL.
1997 Jul 01 22
Loading...
+ 51 hidden pages