Samsung SWA-8500S User Manual

USER MANUAL

SWA-8500S

Safety Information

Thank you for purchasing this product (SWA-8500S).

CAUTION

RISK OF ELECTRIC SHOCK.

DO NOT OP EN

This symbol indicates that

high voltage is present inside.

It is dangerous to make any

kind of contact with any

internal part of this product.

Class II product : This symbol indicates that it does not require a safety connection to
electrical ear th (ground).

AC voltage : This symbol indicates that the rated voltage marked with the symbol is AC
voltage.

DC voltage : This symbol indicates that the rated voltage marked with the symbol is DC
voltage.

Caution, Consult ins tructions for use : This symbol instruct s the user to consult the user
manual for further safety related information.

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE THE
COVER (OR BACK ). THERE ARE NO USER
SERVICEABLE PARTS INSIDE. REFER ALL

SERVICING TO QUALIFIED PERSONNEL.

• The slots and openings in the cabinet and
in the back or bottom are provided for
necessary ventilation. To ensure reliable
operation of this apparatus, and to protect it
from overheating, these slots and openings
must never be blocked or covered.

– Do not place this apparatus in a conned

space, such as a bookcase, or built-in
cabinet, unless proper ventilation is
provided.

– Do not place this apparatus near or over

a radiator or heat register, or where it is
exposed to direct sunlight.

This symbol indicates

that important literature

concerning operation and

maintenance has been

included with this product.

– Do not place vessels (vases etc.)

containing water on this apparatus.

A water spill can cause a re or electric

shock.

• Do not expose this apparatus to rain
or place it near water (near a bathtub,
washbowl, kitchen sink, or laundry tub, in
a wet basement, or near a swimming pool,
etc.). If this apparatus accidentally gets wet,
unplug it and contact an authorized dealer
immediately.

• Do not overload wall outlets, extension cords
or adaptors beyond their capacity, since this

can result in re or electric shock.

ENG - 2 ENG - 3

• Route power-supply cords so that they are
not likely to be walked on or pinched by items
placed on or against them. Pay particular
attention to cords at the plug end, at wall
outlets, and the point where they exit from
the apparatus.

• To protect this apparatus from a lightning
storm, or when it is left unattended and
unused for long periods of time, unplug it from
the wall outlet and disconnect the antenna or
cable system. This will prevent damage to the
set due to lightning and power line surges.

• Before connecting the AC power cord to the
DC adaptor outlet, make sure the voltage
designation of the DC adaptor corresponds to
the local electrical supply.

• Never insert anything metallic into the open
parts of this apparatus. Doing so may create a
danger of electric shock.

• To avoid electric shock, never touch the inside

of this apparatus. Only a qualied technician

should open this apparatus.

• Make sure to plug the power cord in until it is

rmly seated. When unplugging the power

cord from a wall outlet, always pull on the
power cord’s plug. Never unplug by pulling on
the power cord. Do not touch the power cord
with wet hands.

• If this apparatus does not operate normally

- in particular, if there are any unusual
sounds or smells coming from it - unplug it
immediately and contact an authorized dealer
or service centre.

• Maintenance of Cabinet.
– Before connecting other components to

this product, be sure to turn them off.

• Be sure to pull the power plug out of the

outlet if the product is to remain unused or
if you are leaving the house for an extended
period of time (especially when children,
elderly, or disabled people will be left alone in
the house).

– Accumulated dust can cause an electric

shock, an electric leakage, or a re by

causing the power cord to generate sparks
and heat or the insulation to deteriorate.

• Contact an authorized service centre for

information if you intend to install your
product in a location with heavy dust, high or
low temperatures, high humidity, chemical
substances, or where it will operate 24 hours
a day such as in an airpor t, a train station, etc.
Failing to do so may cause serious damage to
your product.

• Use only a properly grounded plug and wall

outlet.

– An improper ground may cause electric

shock or equipment damage. (Class l
Equipment only.)

• To turn this apparatus of f completely, you

must disconnect it from the wall outlet.
Consequently, the wall outlet and power plug
must be readily accessible at all times.

• Do not allow children to hang on the product.

• Store the accessories (battery, etc.) in a

location safely out of the reach of children.

• Do not install the product in an unstable

location such as a shaky self, a slanted oor,

or a location exposed to vibration.

• Do not drop or strike the product. If the
product is damaged, disconnect the power
cord and contact a service centre.

• To clean this apparatus, unplug the power
cord from the wall outlet, and then wipe
the product using a soft, dry cloth. Do not
use any chemicals such as wax, benzene,
alcohol, thinners, insecticide, air fresheners,
lubricants, or detergent. These chemicals can
damage the appearance of the product or
erase the printing on the product.

• Do not expose this apparatus to dripping

or splashing. Do not put objects lled with

liquids, such as vases, on the apparatus.

• Do not plug multiple electric devices into the
same wall socket. Overloading a socket can

cause it to overheat, resulting in a re.

WARNING :

• TO PREVENT THE SPREAD OF
FIRE, KEEP CANDLES AND

OTHER ITEMS WITH OPEN
FLAMES AWAY FROM THIS

PRODUCT AT ALL TIMES.

• To reduce the risk of re or electric shock, do
not expose this appliance to rain or moisture.

Precautions

1. Ensure that the AC or DC power supply

in your house complies with the power

requirements listed on the identication

sticker located on the back of your product.
Install your product horizontally, on a
suitable base (furniture), with enough space
around it for ventilation (7~10 cm).
Make sure the ventilation slots are not

covered. Do not place the unit on ampliers

or other equipment which may become hot.
This unit is designed for continuous use.
To fully turn off the unit, disconnect the AC
plug from the wall outlet.

2. Do not expose the unit to direct sunlight

or other heat sources. This could lead
to overheating and cause the unit to
malfunction.

3. Unplug the Power cord from the AC wall

socket if the unit malfunctions. Your product

is not intended for industrial use. It is for
personal use only. Condensation may occur
if your product has been stored in cold
temperatures. If transporting the unit during
the winter, wait approximately 2 hours until
the unit has reached room temperature
before using it.

4. If the electricity supplied to your home is

rated at 240V AC, use a suitable plug adapter
to connect this unit to your electrical outlets.

ENG - 4 ENG - 5

Important Safety Instructions

Read these operating instructions carefully
before using the unit. Follow all the safety
instructions listed below. Keep these operating
instructions handy for future reference.

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with a dry cloth.

7. Do not block any ventilation openings. Install

in accordance with the manufacturer’s
instructions.

8. Do not install near any heat sources such

as radiators, heat registers, stoves, or other
apparatus (including AV receivers) that
produce heat.

9. Do not defeat the safety purpose of the

polarized or grounding-type plug.
A polarized plug has two blades with one
wider than the other. A grounding type
plug has two blades and a third grounding
prong. The wide blade or the third prong
are provided for your safety. If the provided

plug does not t into your outlet, consult an

electrician for replacement of the obsolete
outlet.

10. Protect the power cord from being walked

on or pinched particularly at plugs,
convenience receptacles, and the point
where it exits the apparatus.

11. Only use attachments/accessories specied

by the manufacturer.

12. Use only with the cart,

stand, tripod, bracket,

or table specied by the

manufacturer, or sold with

the apparatus. When a cart

is used, use caution when moving the cart/
apparatus combination to avoid injury from
tip-over.

13. Unplug this apparatus during lightning

storms or when you intend to leave it unused
for long periods of time.

14. Refer all servicing to qualied service

personnel. Servicing is required when the
apparatus has been damaged in any way,
such as when the power-supply cord or plug
is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus
has been exposed to rain or moisture, does
not operate normally, or has been dropped.

Accessories

SURROUND-LEFT

ID SET

L

R

SURROUND SPEAKERS OUT
SPEAKER IMPEDANCE : 3Ω

POWER

L

R

SURROUND-RIGHT

SURROUND-LEFT SURROUND-RIGHT

STANDBY

LINK

Surround Speaker (2EA) Power Cord

Wireless Receiver Module Speaker Cable (2EA)

Specications

Weight

Wireless Receiver Module 0.7 kg

Surround Speaker 0.5 kg

Wireless Receiver Module 50.0 X 201.3 X 132.0 mm

Dimensions (W x H x D)

Surround Speaker 76.2 X 126.9 X 76.2 mm

Operating Temperature Range +5°C to +35°C

Operating Humidity Range 10% ~ 75%

Output Refer to the Owner’s Manual.

Frequency range 20Hz~20KHz

NOTES

– Samsung Electronics Co., Ltd reserves the right to change the specications without notice.
– Weight and dimensions are approximate.
– For more information about the power supply and power consumption, refer to the label attached

to the product.

– Design and specications are subject to change without prior notice.

Open Source Licence Notice

• To send inquiries and requests regarding open sources, contact Samsung via Email
([e-mail]).

ENG - 6 ENG - 7

Connecting the SWA-8500S to a Soundbar

L

R

1. Connect the Wireless Receiver Module to 2 Surround Speakers

Use the speaker cables to connect the two surround sound speakers to the Wireless Receiver

Module.

• The speaker cables are colour coded.

L

R

SURROUND SPEAKERS OUT

SURROUND-LEFT SURROUND-RIGHT

SPEAKER IMPEDANCE : 3Ω

ID SET

SURROUND-LEFT

POWER

SURROUND-RIGHT

• When connecting the speaker cables to the Wireless Receiver Module, follow these steps:

1. Insert the grey plug into the grey jack on the Wireless Receiver.

2. Insert the blue plug into the blue jack on the Wireless Receiver.

• When connecting the speaker cables to the surround speakers, follow these s teps:

1. Match the speaker cable connected to the grey jack to the speaker with the grey label.

2. Match the speaker cable connected to the blue jack to the speaker with the blue label.

3. Insert the red and black coloured ends of each speaker cable into the red and black jacks of

the appropriate speaker.

• The labels are on the backs of the speakers.

2. Check the standby status after plugging into an electrical outlet

POWER

LINK

VOL

SOUNDBAR

5 Sec

STANDBY

LINK

LINK

Plug the Wireless Receiver Module power cord into an electrical outlet and into the Wireless
Receiver Module to turn on the Wireless Receiver Module. The LINK LED indicator (blue LED) on the
Wireless Receiver Module blinks. If the LED does not blink, refer to step 7 on page 10.

L

SURROUND SPEAKERS OUT
SPEAKER IMPEDANCE : 3Ω

ID SET

R

POWER

STANDBY

LINK

Blue blinking

3. Turn off the Soundbar

Turn off the Soundbar using the Soundbar’s remote control or by pressing the (Power) button
on the main Soundbar unit.

OFF

• The image of the Soundbar may differ from your Soundbar, depending on the model.

ENG - 8 ENG - 9

4. Congure “ID SET” using the Soundbar’s remote control

SOUNDBAR

LINK

Press the VOL button on your remote control for 5~6 seconds until the “ID SET” message appears
on your Soundbar ’s display.

5 Sec

VOL

ID SET

• The image of the Soundbar may differ from your Soundbar, depending on the model.

5. Turn on the Soundbar

Turn on the Soundbar using the Soundbar’s remote control or by pressing the (Power) button on
the main Soundbar unit.

ON

• The image of the Soundbar may differ from your Soundbar, depending on the model.

6. Check if the LINK LED is solid blue (connection complete)

The LINK LED indicator stops blinking

STANDBY

LINK

Blue is On

and glows a solid blue when a
connection is established between the

Soundbar and the Wireless Receiver

Module.

7. If the SWA-8500S does not connect, take the necessary steps

according to the LED Indicator’s status

LED status Action

On

LINK (Blue)

Blinking

STANDBY (Red) On Connection failure

Others - Errors Contact a Samsung Service Centre.

Connected with
the Soundbar

Connection
standby status

-

Check if the Soundbar is turned on

Repeat steps 3 through 6.

Check if the Soundbar is turned on

1. Press the ID SET button on the back

of the Wireless Receiver Module with

a pen tip for 5~6 seconds until the
LINK LED indicator blinks (in Blue).

L

R

SURROUND SPEAKERS OUT
SPEAKER IMPEDANCE : 3Ω

ID SET

2. Repeat steps 3 through 6.

Compatible Models

5 Sec

ID SET

HW-M360 HW-M369 HW-M450 HW-M460

HW-M4500 HW-M4501 HW-M4510 HW-M4511

HW-M550 HW-M560

• The model list is subject to change without further notice.

ENG - 10

© 2017 Sam sung Electronics Co., Ltd. All rights res erved.

Contact SAMSUNG WORLD WIDE

If you have any quest ions or comment s relating to Samsung product s, please cont act the SAMS UNG customer

care Centre.

Area Contact Centre

`

Asia Paci c

CHINA 400-810-5858 www.samsung.com/cn/support

HONG KONG 3698 4698

MACAU 0800 333 www.samsung.com/support

SINGAPORE 1800-SAMSUNG(726-7864) www.samsung.com/sg/support

AUSTRALIA 1 300 362 603 www.samsung.com/au/support

NEW ZEALAND 0800 7 26 786 www.samsung.com/nz/support

VIETNAM 18 00 588 88 9 w ww.samsung.com/vn/support

THAILAND 0-2689-3232, 1800-29-3232

MYANMAR [phone]

MALAYSIA

INDONESIA

PHILIPPINES

TAIWAN 0800-329999 www.samsung.com/tw/support

JAPAN 0120-363-905 www.samsung.com/jp/support

INDIA

BANGLADESH

SRI LA NKA

1800-88-9999
603-7 7137477 (Ov erseas con tact)

021-56997777
08001128888

1-80 0-10-726 -7864 [ PLDT Toll Fr ee ]
1-80 0-8-726 -7864 [ Glo be Landlin e and Mobile ]
02-42 2-2111 [ Standar d Landline ]

1800 30 00 8282 - Toll Free
1800 26 6 8282 - Toll Free

0961-2300300
0800-0300300 (Toll free)

0117540540
0115900000



Web Site

www.samsung .com/hk/support (Chinese)
www.samsung.com/hk_en/support (English)

www.samsung.com/th/support

www.samsung.com/my/support

www.samsung.com/id/support

www.samsung.com/ph/support

www.samsung .com/in/support

www.samsung.com/support

AH68-02989W-00

AH68-02989W-00