Samsung SW80W1P, SW80W1, SW80W2P, SW80W2 Service Manual

WASHING MACHINE

SW80W1(P)
SW80W2(P)

WASHING MACHINE CONTENTS

F

U

L

L

Y

A

UT

O

MA

TI

C

WA

SH

IN

G

MA

CH

IN

E

WASH

RINSE

SPIN

FUZZY

SOAK

WOOL

SPEEDY

HIGH

HOT

COLD

WATER SUPPLY

WATER LEVEL

COURSE

FUNCTION

MEDIUM

LOW

EXTRA LOW

START/HOLD

POWER

1. Precautions

2. Specifications

3. Features

4. Operating Instructions

5. Schematic and Wiring Diagrams

6. Disassembly and Reassembly

7. Troubleshooting

8. Exploded Views

9. Power Cord

1. Precautions

When performing trouble - shooting and part replacement during servicing note the following safety precautions.

1-1 Safety Precautions

1-1-1 Use Genuine Parts

The components of the washing machine have safety ­features such as non - combustibility and voltage
withstanding. Therefore, always use the same part as
used when replacing parts. In particular, be sure to use
only designated parts in case of major safety parts
identified by the making.

1-1-2 Grounding

Connect the grounding wire to the shell plate, and bury
it under at least 25cm of earth ; alternatively, connect
the ground wire to the appropriate pin on a properly
grounded power receptacle.

✵ Never ground it to the telephone line, lightning rod,

or gas pipe.

1-2 Servicing Precautions

1-2-1 Observe warnings

Be sure to follow special warnings and precautions that
are described on part labels and in the owner's manual.

1-2-2 Special Precautions for Parts Assembly

and wiring

When assembling parts that use safety - insulation
material (such as tube and tape), or when installing
internal wiring, be sure to restore all parts and wiring to
their original positions.
Take special care to avoid contact with sharp edges.

1-2-3 Safety Checks after Servicing

After servicing, check to see that the screws, parts, and
wiring are restored to their original positions, and
check the insulation between the external metals and
the socket plug. In addition, place the washing machine
in a level position (less than 1û of grade) to prevent
vibration and noise during operations.

1-2-4 Insulation Check

Pull out the plug from the power receptacle, pour water
into the spin tub, and then set the timer. Check to see
that the insulation resistance between the terminals of
the plug and the exposed metal is greater, than 1 M½.

Note : When it is impossible to perform the insulation

check with a 500V insulation resistance tester,
use other testers for inspection.

SAMSUNG ELECTRONICS CO., LTD 1-1

©Samsung Electronics Co., LTD.
All right reserved.
The information in this manual is subject to change without notice.

Copyright

2. Specifications

Classifications Specifications

Washing and Dehydrating Capacity 6.0 kg
Washing Method Heavy duty rotation type (centripetal current)
Standard Volume of Water High Level 57 l

Medium Level 46 l
Low Level 38 l

Extra low level 32 l
Applicable Volume of Water 160 l (high level of water)
Rotation of the Pulsator 128rpm
Rotation of the Spin Tub 770rpm
Power Consumption Washing 330 W

Spinning 270 W
Dehydration Method Centrifugal dehydration type
Drain Control Motor driven
Applicable Water Pressure 0.5 kg f / cm2 ~ 8.0 kg f / cm

2

Weight Gross 38kg

Net 35kg
Dimension Gross W 580mm X D 620mm X H 890mm

Net W 560mm X D 580mm X H 915mm
Accessories Water supply hose, drain hose, owner's manual

2-1 WASHING MACHINE

560

350

915

30

1260

1085

915

3. Features

3-1 Dimensions

3-2 Installation

3-2-1 Level Specifications and Wall - Clearance

Distances

1. Install the washing machine on a solid and level
floor.

2. Place the machine at least 40cm away from the wall.

3. Placement on an inclined, weak or rough floor may
cause abnormal trembling.

3-2-2 Balance

1. Adjust horizontally : First ①, Then ②.

2. If the thread is not within
the limit, adjust the height
of the legs.

3-2-3 Controlling the Front Adjustable Leg

To control the height, turn the adjustable leg.

3-2-4 Connecting the Drain Hose

1. After pressing the joint ring(a), insert the drain hose
(b) in the drain direction. (Same as pump model.)

2. Install the drain hose about 70~80cm
above the ground (for pump model).

SAMSUNG ELECTRONICS CO., LTD 3-1

F

U

LL

Y

AU

TO

MA

TIC

WA

SH
I

NG

MA

CH

I

NE

W

ASH
RINSE
SPIN

FUZZY
SOAK
WOOL
SPEEDY

HIGH

HOT

COLD

WATER SUPPLY

WATER LEVEL

COURSE

FUNCTION

MEDIUM

LOW
EXTRA LOW

START/HOLD

POWER

(a)

(b)

F

UL

LY

AU
T

OM

A

TIC

WA

S

HIN
G

MA
C

HIN

E

WASH
RINSE

SPIN

F
U
Z

Z

Y
SO
AK

WOOL
S
P
E
E
D

Y

HIGH

HOT

COLD

W
A
T
E
R
S

U
P
P
L
Y

WATER LEVEL

C

O
URSE

FU

NCTIO

N

MEDIUM

LOW
EXTRA LOW

START/HOLD

POWER

2

1

3-2-6 Positioning the Drain Hose

1. When there is no threshold, the length of
the drain hose should not exceed 3m.

2. When it is necessary to connect the drain
hose with the drain outlet located far
away, connect the extension hose and
applicable parts (available from dealers
or service centers).

3. Do not install the drain hose where it
must extend over a threshold of 5cm or
more ; do not install where there is a
threshold and the hose must extend for
more than 2m.

3-2-5 Connecting the water supply hose

4. Other precautions

3-2 WASHING MACHINE

3. Features

1. Romove the adaptor from the
water supply hose.

2. First, using a "+" type screwdriver,
loosen the three screws on the
adaptor.
Next, take the adaptor and hold
parts (a) and (b) with a gap about
5mm between them.

a

b

3. Connect adaptor to the water tap
by firmly tightening the screws.
Then turn part (b), following the
arrow, and put (a) and (b) toge­ther.

a
b

4. Connect the water supply hose
to the adaptor. Pull down part (c)
of the water supply hose. When
part (c) is released, the hose is
automatically connected to the
adaptor, and makes a 'click'
sound.

c

5. Connect the other end of the
water supply hose to the inlet
water valve at the back of the
washer.
Screw the hose clockwise, all the
way in.

If the water tap is a screw type,
connect a water supply hose that
fits to the tap as shown.

Do not put the end of the drain
hose into the water.

Do not place the hose below the
floor level of the drain outlet.

Do not make the mid part of the
hose than the ends positioned
higher.

If the drain hose must be
positioned at a high angle, install
the washing machine so that it is
in an even higher position.

3m

2m

5cm

DRAIN HOSE
(Pump)

WATER SUPPLY HOSE
(COLD)

LID

DETERGENT BOX

GROUND LEAD

WATER DRAIN HOSE

WIDE FALL

GUIDE

POWER CORD

SOUND ABSORPTION
PANEL

WATER SUPPLY HOSE
(HOT )

FRONT

CONTROL PANEL

BLEACH INLET

SPIN BASKET

ADJUSTABLE LEGS

MAGIC HAND

PULSATOR

F

U

L

L

Y

A

U

T

O

M

AT

IC

W

AS

HI

NG

M

AC

HI

NE

WASH

RINSE

SPIN

FUZZY

SOAK

WOOL

SPEEDY

HIGH

HOT

COLD

WATER SUPPLY

WATER LEVEL

COURSE

FUNCTION

MEDIUM

LOW

EXTRA LOW

START/HOLD

POWER

4. Operating Instructions

4-1 Component Identification

SAMSUNG ELECTRONICS CO., LTD 4-1

4-2 Control Panel

4-2-1 Function Indicator Light

1. In use indicated by a flashing symbol.

2. The light goes out at the end of the function.

4-2-2 Start/Hold

1. Press this button to alternately 'start' or 'hold'.

2. This button is a convenient way to change washing
courses or a commands.

4-2-3 Power

1. Press this button for power ON/OFF.

2. When the washing operation is completed, the
power automatically turns off and the buzzer
sounds off 5 times.

3. Allow at least a 3-second interval before turning the
washing machine again .

4-2-4 Water Supply (option)

1. Press this button to select water temperature.

2. The selection order is :

Cold →Cold+Hot → Hot →Cold

3. Selecting the Wool Course automatically selects
cold water (to protect the wool fabric)

4-2-5 Water Level

1. Press this button to select the water height.

2. The selection order is :

High → Medium → Low → Extra low

3. Selecting the Wool Course limits the water levels to
high or medium.

4-2-6 Course

1. Press this button to select the type of washing cycle.

4-2-7 Function

1. The selection order is :

Fuzzy → Soak → Wool → Speedy

4-2 WASHING MACHINE

4. Operating Instructions

WASH

RINSE
SPIN

FUZZY
SOAK
WOOL

SPEEDY

HIGH

HOT

COLD

MEDIUM

LOW

EXTRA LOW

F

U

L

L

Y

A

U

T

O

M

A

T

I

C

W

A

S

H

I

N

G

M

A

C

H

I

N

E

WATER SUPPLY

WATER LEVEL

COURSE

FUNCTION

START/HOLD

POWER

4-3-1 Water Supply

1. In all the cases of prior to the first press of START/HOLD
key, during operating or hold state, they follow the below
sequences.

2. When wool course is selected, water supply is selected
automatically to cold water without key input.

3. Once water supply is changed by key input, this water
supply keeps on the changed course.
In case of wool course, cold water is selected automatically,
but if the user'd like to change it to other course, the course
will return to the previous course.

4. While water supplying, the lamp selected is flashing(one
second ON/OFF)

4-3-2 Water Level

1. In all the cases of prior to the first press of START/HOLD
key, during operating or hold state, they follow the below
sequences.

2. When WOOL is selected, only HIGH & MEDIUM water
level is possible.

3. If you change the course to WOOL, in case previous water
level is low or medium, the water level is automatically
selected High level and in case previous water level is over
Low, the water level is not changed.

4. While water is supplying, if the water level is changed, the
remaining time is changed.

4-3-3 Course

1. If this key is pressed before the first press of START/HOLD
key or during HOLD state, the selection order is as follow.
Even if manual washing is selected already, the selected
course is cancelled, and the course is selected as follow.

2. During operating, all keys except for COURSE SELECTION
key are valid.
But, only START/HOLD is vaild during spin operation.

3. During operating, If anykey is pressed after pressing the
START/HOLD key, new Selection course is performed, not
related to previous course.

4. This key is invalid during operation.

4-3-4 Function Button

1. This key is valid except for weight sensing operation.

2. After START/HOLD during operation or under reset
condition, as pressing this key display is changing as
follows.

3. The beginning conditions are as follows when function key
is selected.

4. This key is used as adjusting function.

①Rinsing times are added by one time when function

key is pressed under general course operation
(FUZZY, SOAK, WOOL and SPEEDY) and
function operation (RINSE, WASH+RINSE,
RINSE+SPIN, WASH+RINSE+SPIN) as pressing
this key.
Display is changing as follows.

➁Washing time is adjusted by press of function

key during washing only operation.

③Spinning time is adjusted by press of function key

during spinning only operation.

4-3-6 Start/Hold

1. Available only after selecting a course.

2. Sequence :

3. The display shows the remaining time, including the current
function, when in 'start' status.

The time decreases 1-min at a time.
When in 'Hold' status, the time stays as it is.

4-3-7 Power

1) This key is always available when the power cord is
connected.

2) sequence :

3) After finishing operation, this key is automatically turned
off.

4-3 Function Descriptions

SAMSUNG ELECTRONICS CO., LTD 4-3

4. Operating Instructions

→ FUZZY → SOAK → WOOL → SPEEDY

→ COLD → COLD +HOT → HOT

→

HIGH →MEDIUM →LOW →EXTRA LOW

FUNCTION

WASH

RINSE

SPIN

WASH+RINSE

RINSE+SPIN

WASH+RINSE+SPIN

TIME

23 min
15 min

9 min
43 min
24 min
52 min

→ 2 (times) → 3 → 4 → 5 →1

→ START → HOLD → START

→ ON → OFF → ON

→ WASH → RINSE → SPIN → WASH+RINSE →

RINSE+SPIN → WASH+RINSE+SPIN

→

20 (min) → 21 → 23 → 25 → 3 → 5 → 7 → 9

•••

→ 17 → 19

→ 7 (min) → 1 → 2 → ••• → 6

4-4 Description of Technical Points

4-4-1 Weight Recognizing Function

1. Weight recognizing function works first washing
operating before water is supplied, not in WOOL
course and Manual function operation (Wash,

Rinse, Spin, ..... )

2. Weight recognizing function is cancelled when
water level key is pressed prior to the completion of
weight recognizing function.

3. If the current water level is above lowest at the
beginning of weight sensing, it is automatically
decided as a high level.

4. If you change courses after sensing weight, the high
water level is automatically selected irrespective of
the water level decided by the sensing of weight.

4-4-2 Water Supplying Function

1. Relations between water level, frequency & water
supply capacity.

2. Relations between Hot/Cold selection & cycle.

3. If the water level does not reach to the water level
selected for 60minutes after starting water
supplying, the water supplying Error is displaying
on the display.

4. Supplementary water supplying is performed
every Washing or Rinsing operating. The steps are
as follows.

●supply water to the water level selected,

●perform the washing or Rinsing operation for 1.5

minutes.

●sense the present water level after stopping

Motor.

●compare the present water level to the water

level selected.

●if present water level < the water level selected,

supply water to the water level selected.

if present water level ≥the water level selected,

continue the washing or Rinsing operation.

●But total time of supplementary water

supplying is not over 30 seconds.

4-4-3 Soak Function

1. This course works only when Soak washing is
selected by course select key.

2. It works repeatedly during set time by every 5
minutes(operation for 1 minute and pause for 4
minutes) for 30 minutes after water is filled to
selected water level.

3. If water level is set higher during the Soak
procedure, Soak procedure stops and water is
refilled, and then, keeps on going the Soak
procedure.

4. Washing cycle of 20 minutes begins after Soak
function completion.
Rinsing times can be adjusted according to Soak
washing procedure.

4-4-4 Fuzzy Function

This function recognizes the quantity of laundry
load and selects the water level by itself and keep
on going washing operation automatically.

4-4 WASHING MACHINE

4. Operating Instructions

unit :l fre :

KHz

RESET

MIN

LOW

MEDIUM

HIGH

0 24.8

32 l 23.8
38 l 23.4
46 l 23.0

57 l 22.6

amount of water

fre

supplied

Hot/Cold

Wash Rinse

Supplementary

Pre

Remarks

selection

Water supply

spinning

Cold Cold Cold Cold Cold

Hot / Cold Hot / Cold Hot / Cold Hot / Cold Hot / Cold

Hot Hot

Hot / Cold Hot / Cold Hot / Cold

50Hz FUZZY HIGH

/

MEDIUM

60Hz

LOW

EXTRA LOW

SOAK HIGH

MEDIUM

LOW

EXTRA LOW

WOOL HIGH

MEDIUM

SPEEDY HIGH

MEDIUM

LOW

EXTRA LOW

3' 20' 1'30" 1' 1'30" 1' 3' 2' 1'30" 1' 1'30" 1' 3' 2' 1'30" 1' 5' 1'

51'30"

2'30" 20' 1'15" 1' 1'30" 1' 2'30" 2' 1'15" 1' 1'30" 1' 2'30" 2' 1'15" 1' 5' 1'

49'15"

2' 20' 1' 1' 1'30" 1' 2' 2' 1' 1' 1'30" 1' 2' 2' 1' 1' 4' 1'

46'

1'30" 20' 45" 1' 1'30" 1' 1'30" 2' 45" 1' 1'30" 1' 1'30" 2' 45" 1' 4' 1'

43'45"

3' 30' 20' 1'30" 1' 1'30" 1' 3' 2' 1'30" 1' 1'30" 1' 3' 2' 1'30" 1' 5' 1'

81'30"

2'30" 30' 20' 1'15" 1' 1'30" 1' 2'30" 2' 1'15" 1' 1'30" 1' 2'30" 2' 1'15" 1' 5' 1'

79'15"

2' 30' 20' 1' 1' 1'30" 1' 2' 2' 1' 1' 1'30" 1' 2' 2' 1' 1' 4' 1'

76'

1'30" 30' 20' 45" 1' 1'30" 1' 1'30" 2' 45" 1' 1'30" 1' 1'30" 2' 45" 1' 4' 1'

73'45"

3' 10' 1'30" 1' 1' 1' 3' 2' 1'30" 1' 1' 1' 3' 2' 1'30" 1' 1' 1'

36'30"

2'30"

10'30''

1'15" 1' 1' 1' 2'30" 2' 1'15" 1' 1' 1' 2'30" 2' 1'15" 1' 1' 1'

34'15"

3' 8' 1'30" 1' 1' 1' 3' 2' 1'30" 1' 1' 1' 3' 2' 1'30" 1' 5' 1'

38'30"

2'30" 8' 1'15" 1' 1' 1' 2'30" 2' 1'15" 1' 1' 1' 2'30" 2' 1'15" 1' 5' 1'

36'15"

2' 8' 1' 1' 1' 1' 2' 2' 1' 1' 1' 1' 2' 2' 1' 1' 4' 1'

33'00"

1'30" 8' 45" 1' 1' 1' 1'30" 2' 45" 1' 1' 1' 1'30" 2' 45" 1' 4' 1'

30'45"

4-5 Program Chart

SAMSUNG ELECTRONICS CO., LTD 4-5

4. Operating Instructions

WASH RINSE 2 RINSE 1 SPIN

TOTAL

WATER

SOAK WASH DRAIN

INTER-

SPIN STOP

WATER

RINSE DRAIN

INTER-

SPIN STOP

WATER

RINSE DRAIN

INTER-

SPIN STOP MIN

SUPPLY MITTENT SUPPLY MITTENT SUPPLY MITTENT

FREQUENCY

COURSE

WATER

LEVEL

TIME

4-6 WASHING MACHINE

4. Operating Instructions

50Hz WASH HIGH

/

MEDIUM

60Hz

LOW

EXTRA LOW

RINSE HIGH

MEDIUM

LOW

EXTRA LOW

SPIN HIGH

MEDIUM

LOW

EXTRA LOW
WASH HIGH
RINSE MEDIUM

LOW

EXTRA LOW
RINSE HIGH

SPIN MEDIUM

LOW

EXTRA LOW
WASH HIGH
RINSE MEDIUM

SPIN LOW

EXTRA LOW

3' 20'

23'00"

2'30" 20'

22'30"

2' 20'

22'

1'30" 20'

21'30"

3' 2' 1'30" 1' 1'30" 1' 3' 2'

15'

2'30" 2' 1'15" 1' 1'30" 1' 2'30" 2'

13'45"

2' 2' 1' 1' 1'30" 1' 2' 2'

12'

30"

1'30" 2' 45" 1' 1'30" 1' 1'30" 2'

11'15"

1'30" 1' 5' 1'

8'30"

1'15" 1' 5' 1'

8'15"

1' 1' 4' 1'

7'

45" 1' 4' 1'

6'45"

3' 20' 1'30" 1' 1'30" 1' 3' 2' 1'30" 1' 1'30" 1' 3' 2'

43'

2'30" 20' 1'15" 1' 1'30" 1' 2'30" 2' 1'15" 1' 1'30" 1' 2'30" 2'

41'

2'00" 20' 1" 1' 1'30" 1' 2' 2' 1' 1' 1'30" 1' 2' 2'

39'

1'30" 20' 45" 1' 1'30" 1' 1'30" 2' 45" 1' 1'30" 1' 1'30" 2'

37'

3' 2' 1'30" 1' 1'30" 1' 3' 2' 1'30" 1' 5' 1'

23'30"

2'30" 2' 1'15" 1' 1'30" 1' 2'30" 2' 1'15" 1' 5' 1'

22'

2' 2' 1' 1' 1'30" 1' 2' 2' 1' 1' 4' 1'

19'30"

1'30" 2' 45" 1' 1'30" 1' 1'30" 2' 45" 1' 4' 1'

18'

3'00" 20' 1'30" 1' 1'30" 1' 3' 2' 1'30" 1' 1'30" 1' 3' 2' 1'30" 1' 5' 1'

51'30"

2'30" 20' 1'15" 1' 1'30" 1' 2'30" 2' 1'15" 1' 1'30" 1' 2'30" 2' 1'15" 1' 5' 1'

49'15"

2' 20' 1' 1' 1'30" 1' 2' 2' 1' 1' 1'30" 1' 2' 2' 1' 1' 4' 1'

46'

1'30" 20' 45" 1' 1'30" 1' 1'30" 2' 45" 1' 1'30" 1' 1'30" 2' 45" 1' 4' 1'

43'45"

WASH RINSE 2 RINSE 1 SPIN

TOTAL

WATER

WASH DRAIN

INTER-

SPIN STOP

WATER

RINSE DRAIN

INTER-

SPIN STOP

WATER

RINSE DRAIN

INTER-

SPIN STOP MIN

SUPPLY MITTENT SUPPLY MITTENT SUPPLY MITTENT

FREQUENCY

COURSE

WATER

LEVEL

TIME