Samsung SV-232B User Manual

VIDEO

CASSETTE RECORDER

SV-633B

SV-630B

SV-6303B

SV-233B

SV-231B

SV-230B

Instruction Manual

www.samsungvcr.com

PAL

Safety Precautions

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION. TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE REAR COVER. NO USER SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL.

IMPORTANT NOTE

The mains lead on this equipment is supplied with a moulded plug incorporating a fuse. The value of the fuse is indicated on the pin face of the plug. If it requires replacing, a fuse approved to BS1362 of the same rating must be used.

Never use the plug with the fuse cover omitted if the cover is detachable. If a replacement fuse cover is required, it must be of the same colour as the pin face of the plug. Replacement covers are available from your dealer.

If the fitted plug is not suitable for the power points in your house or the cable is not long enough to reach a power point, you should obtain a suitable safety approved extension lead or consult your dealer for assistance.

However, if there is no alternative to cutting off the plug, remove the fuse and then safely dispose of the plug. Do not connect the plug to a mains socket, as there is a risk of shock hazard from the bared flexible cord.

IMPORTANT

The wires in the mains lead are coloured in accordance with the following code: -

BLUE = NEUTRAL

BROWN = LIVE

As these colours may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: -

The wire coloured BLUE must be connected to the terminal marked with the letter N or coloured BLUE or BLACK. The wire coloured BROWN must be connected to the terminal marked with the letter L or coloured BROWN or RED.

WARNING: DO NOT CONNECT EITHER WIRE TO THE EARTH TERMINAL WHICH IS MARKED WITH THE LETTER E OR BY THE EARTH SYMBOL , OR COLOURED GREEN OR GREEN AND YELLOW.

DANGER

This symbol is intended to alert you to the presence of dangerous voltage within the product.

CAUTION

This symbol is intended to alert you to the presence of important instructions accompanying the product.

2

About this manual

GB

Thank you for purchasing a Samsung Video Cassette Recorder (VCR).

Your Owner’s Instructions contain much valuable information on setting up and using your VCR. Please take the time to read them as they will help you take full advantage of your VCR’s features.

The instructions in this manual are for models, SV-633B, SV-630B, SV-6303B, SV-233B, SV-231B and SV-230B.

Before you start reading this manual please check your model number. It is displayed on the rear of the VCR.

-(SV-633B): Exceptions only for a certain model, for example SV-633B.

-Gray shaded areas marked with a star indicate instructions that are only relevant to one model.

Features Chart

Model

SV-633B

SV-630B

SV-233B

SV-231B

SV-230B

Feature

SV-6303B

 

 

 

 

 

 

 

 

 

 

 

VIDEOPLUS+ Recording

 

 

AV2 IN socket

 

 

 

Format 16:9

 

 

 

Child Door Lock

IPC (Intelligent Picture Control)

Quick Programming

Auto Clock Setting

 

 

PDC (Programme Delivery Control)

 

 

Changing recording speed (SP/LP)

Hi-Fi

 

 

 

NICAM

 

 

 

 

 

 

 

 

 

3

 

Contents

 

B

 

 

FOREWORD

 

Safety Instructions .........................................................................................

6

VCR OVERVIEWS

 

Front View of the VCR...................................................................................

7

Rear View of the VCR ...................................................................................

7

Infrared Remote Control ................................................................................

8

Display Indicators ..........................................................................................

9

Accessories ...................................................................................................

9

CONNECTING YOUR VIDEO CASSETTE RECORDER

 

Deciding How to Connect Your VCR.............................................................

10

Connecting Your VCR to the TV using the Coaxial Cable.............................

11

Connecting Your VCR to the TV using the SCART Cable ............................

11

Connecting Your VCR to the Satellite receiver or Other Equipment .............

12

Connecting the Audio Output Cable (SV-633B/SV-630B/SV-6303B Only) ...

13

Plug & Auto Set Up........................................................................................

13

Tuning Your Television for the VCR ..............................................................

14

SETTING UP YOUR VIDEO CASSETTE RECORDER

 

Inserting Batteries in the Remote Control......................................................

15

Setting the Date and Time.............................................................................

15

Displaying/Hiding On-Screen Information .....................................................

16

Setting the VCR Output Channel...................................................................

16

Presetting the Stations Automatically ............................................................

17

Presetting the Stations Manually ...................................................................

18

Clearing a Preset Station...............................................................................

19

Changing the Preset Station Table................................................................

20

RECORDING TELEVISION BROADCASTS

 

Selecting the Cassette Type..........................................................................

21

Selecting the Recording Speed .....................................................................

21

NICAM (SV-633B/SV-630B/SV-6303B Only) ................................................

22

Protecting a Recorded Cassette....................................................................

23

Recording a Programme Immediately ...........................................................

23

Recording a Programme with Automatic Stop...............................................

24

Using the VIDEOPLUS+ Feature (SV-633B/SV-233B/SV-231B Only) .........

25

Modifying VIDEOPLUS+ Programming (SV-633B/SV-233B/SV-231B Only)

26

Using the Quick Programming Feature .........................................................

27

Checking a Preset Recording........................................................................

28

Cancelling a Preset Recording ......................................................................

28

PLAYING BACK

 

Playing a Cassette.........................................................................................

29

Adjusting Picture Alignment Manually ...........................................................

29

Intelligent Picture Control ..............................................................................

30

Format 16:9 (Wide Screen) (SV-633B/SV-630B/SV-6303B Only) ................

30

Selecting the Colour Mode ............................................................................

31

Selecting the Audio Output Mode (SV-633B/SV-630B/SV-6303B) ...............

32

Selecting the Audio Mute Mode (SV-233B/SV-231B/SV-230B) ....................

32

4

Contents (cont.)

GB

SEARCHING FOR A SEQUENCE

 

Playing a Cassette in Slow Motion (SV-633B/SV-630B/SV-6303B Only) .....

33

Playing a Sequence Frame by Frame ...........................................................

34

Playing a Sequence at Variable Speeds .......................................................

34

Searching for a Specific Sequence ...............................................................

35

Auto Repeat Play...........................................................................................

36

Interval Repeat Play ......................................................................................

36

Using the Tape Counter ................................................................................

37

ADVANCED RECORDING FEATURES

 

Using the Assemble Edit Function.................................................................

38

Recording from Another VCR or Camcorder.................................................

38

OTHER FUNCTIONS AND USEFUL RECOMMENDATIONS

 

Auto Power Off ..............................................................................................

39

Child Door Lock System ................................................................................

39

Technical Specifications ................................................................................

40

SOLVING PROBLEMS

 

Problems and Solutions.................................................................................

41

Service Centers List ......................................................................................

42

Symbols

1

1

 

 

 

Press/push

Hold down

Important

Note

Option

1 = Step number

 

 

 

5

Samsung SV-232B User Manual

Safety Instructions

B

The following illustrations represent precautions.

The lightning bolt is a warning sign alerting you to dangerous voltage inside the product.

DO NOT OPEN THE VCR. Refer to service personnel.

10%

75%

 

40°C

H

H

 

5°C

Do NOT expose the VCR to extreme temperature conditions (below 5°C and above 40°C) or to extreme humidity conditions (less than 10% and more than 75%).

Do NOT expose the VCR to direct sunlight.

Do NOT expose the VCR to any liquids.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Do NOT place any objects on

 

During a storm and/or light-

 

If the remote control is not

the VCR or remote control.

 

ning, unplug the VCR from the

 

used for a long period of time,

 

 

 

 

 

 

 

 

 

 

 

 

 

 

mains socket and aerial.

 

remove the batteries and store

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

it in a cool, dry place.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

THIS DEVICE IS NOT FOR USE IN INDUSTRIAL

ENVIRONMENTS

6

Front View of the VCR

 

 

 

(SV-633B/SV-630B/SV-6303B)

 

 

GB

 

 

 

STANDBY/ON

VIDEO CASSETTE

RECORD

REW

F.F

BUTTON

 

 

COMPARTMENT

BUTTON

BUTTON

BUTTON

EJECT

 

 

 

 

 

BUTTON

 

 

 

 

 

EJECT

STANDBY/ON

 

 

 

 

 

 

 

 

 

REW PLAY F.F

 

 

PROG

REC STOP

 

 

 

 

PROGRAMME

STOP

 

PLAY

 

 

SELECTION

BUTTON

BUTTON

 

 

BUTTONS

 

 

 

(SV-233B/SV-231B/SV-230B)

STANDBY/ON

VIDEO CASSETTE

RECORD

PLAY BUTTON

COMPARTMENT

BUTTON

BUTTON

 

 

 

 

EJECT

BUTTON

STANDBY/ON

EJECT

REW PLAY F.F

PROG

REC

STOP

 

 

PROGRAM

 

STOP

REW

F.F

SELECTION

BUTTON

BUTTON

BUTTON

BUTTONS

 

 

 

 

Rear View of the VCR

AV2 IN SCART

 

RCA AUDIO L, R

 

(EURO-21) SOCKET

 

OUTPUT SOCKETS

AERIAL IN

(SV-633B/SV-630B/SV-6303B ONLY)

 

(SV-633B/SV-630B/SV-6303B ONLY)

 

CONNECTOR

 

 

 

 

OUT

 

R

AV2 IN

AUDIO

 

L

 

TV

AV1(EURO AV)

 

AV1(EURO AV) IN/OUT

OUT TO TV

SCART (EURO-21) SOCKET

CONNECTOR

7

Infrared Remote Control

B

STANDBY/ON

EJECT

STANDBY/ON BUTTON

SLOW BUTTON (SV-633B/SV-630B/

SV-6303B ONLY)

SHUTTLE BUTTON

V-LOCK BUTTON

CLEAR AND RESET BUTTON

INDEX BUTTON

TUNER, AV1, AV2 (SV-633B/SV-630B/

SV-6303B ONLY) SELECTION BUTTON /

REPEAT SELECTION BUTTON

MENU BUTTON

RECORD BUTTON

RECORDING SPEED SELECTION BUTTON

PLAY/PAUSE/STILL BUTTON (MENU SELECTION UP BUTTON)

REWIND/REVERSE PICTURE SEARCH BUTTON (MENU SELECTION BUTTON)

STOP BUTTON (MENU SELECTION DOWN BUTTON)

8

SLOW

Q-PRO

 

SHUTTLE

IPC

 

V-LOCK

DISPLAY

 

 

CLR/RST

F.ADV

 

INPUT

TRK

PROG

INDEX

 

REPEAT

MENU

 

C

 

AU

E

 

DI

R

 

O

D

 

 

E

 

 

E

 

 

P

 

 

S

 

 

 

OK

 

EJECT BUTTON

QUICK PROGRAMME BUTTON

IPC BUTTON

DISPLAY BUTTON

FRAME ADVANCE BUTTON

PROGRAMME SELECTION BUTTONS

TRACKING BUTTONS

AUDIO MODE SELECTION BUTTON (SV-633B/SV-630B/SV-6303B) / AUDIO MUTE BUTTON (SV-233B/SV-231B/SV-230B)

VIDEOPLUS+ BUTTON(SV-633B/SV-233B/SV-231B ONLY)

FAST-FORWARD/FORWARD SEARCH BUTTON

(MENU SELECTION BUTTON)

OK BUTTON

Display Indicators

GB

 

1

2

3

 

 

V

 

IPC+

 

 

 

 

NICAM

 

4

5

 

6

7

1

Cassette loaded indicator

5

Record indicator

2

Multi-function display

6

NICAM indicator (SV-633B/SV-630B/SV-6303B Only)

3

IPC (Intelligent Picture Control) indicator

7

Hi-Fi indicator (SV-633B/SV-630B/SV-6303B Only)

4

Timer indicator

 

 

 

 

Accessories

You have just purchased a SAMSUNG Video Cassette Recorder (VCR).

Together with your VCR, you will find the following accessories in the box.

REMOTE CONTROL

AUDIO CABLE

OWNER’S

COAXIAL CABLE

(SV-633B/SV-630B/ INSTRUCTIONS

SV-6303B Only)

9

Deciding How to Connect Your VCR

 

Connecting Your VCR to the TV using the Coaxial Cable

 

 

 

B

You must take into account various factors when connecting audio or video systems:

Types of connectors available on your systems

Systems connected permanently to the VCR (satellite receiver for example) or temporarily (camcorder for example)

Your VCR is equipped with the following connectors.

Connector

Location

Type

Direction

Recommended Use

AV1(EURO AV)

Rear

SCART

In/Out

Television

 

 

 

 

Satellite receiver

 

AV1(EURO AV)

 

 

Other VCR

OUT TO TV

Rear

75 Ω

Out

Television

 

TV

coaxial

 

 

 

 

 

 

To receive television programmes a signal must be received from one of the following sources:

1Remove the aerial or network input cable from the television.

2Connect this cable to the 75Ω coaxial socket marked on the rear of your VCR.

3

Plug the coaxial cable supplied into the

TV

socket on your VCR.

 

4Plug the other end of the coaxial cable into the connector previously used for the aerial on the television.

5To obtain better quality pictures and sound on your television, you can also connect your VCR to the television via the SCART cable (see section below) if your television is equipped with this type of connection.

GB

ORTIE

D

AUDIO

G

TV

2

TV

D

AUDIO

G

3

4

IN FROM ANT. Rear

75 Ω

In

Aerial

 

coaxial

 

 

Cable television network

 

 

 

 

Satellite receiver

Connecting Your VCR to the TV using the SCART Cable

AV2 IN

Rear

SCART

In

Satellite receiver

 

 

 

 

 

 

 

 

 

Other VCR

 

 

Aerial

 

 

 

AV2 IN

 

 

 

 

 

 

(SV-633B/SV-630B/SV-6303B Only)

 

 

 

 

 

 

Audio output

Rear

Audio RCA

Out

Audio Hi-Fi system

 

 

 

TV

 

 

OUT

 

 

 

 

 

 

 

 

 

R

 

 

 

 

 

 

 

 

 

AUDIO

 

 

 

 

 

 

 

 

 

L

 

 

 

 

 

 

 

 

 

 

 

 

 

 

OUT

 

 

 

(SV-633B/SV-630B/SV-6303B Only)

 

 

 

R

 

 

 

 

AV2 IN

L

 

 

 

 

 

 

 

AUDIO

 

RF coaxial cable

 

 

 

 

 

 

 

 

TV

 

 

 

 

 

 

AV1(EURO AV)

 

 

3

 

 

 

 

 

 

 

 

 

 

Whenever you connect an audio or video system to your VCR, ensure that all elements are

2

 

 

 

 

 

 

 

 

 

switched off.

 

 

 

 

 

 

 

Refer to the documentation supplied with your equipment for detailed connection instructions and associated safety precautions.

You can connect your VCR to the television using the SCART cable if the appropriate input is available on the television. You thus:

Obtain better quality sound and pictures

Simplify the setting up procedure of your VCR

Regardless of the type of connection chosen, you must always connect the coaxial cable supplied. Otherwise, no picture will be visible on the screen when the VCR is switched off.

Make sure that both the television and the VCR are switched off before connecting the cables.

1Connect the coaxial cable as indicated in the above section.

2Connect one end of the SCART cable to the AV1(EURO AV) socket on the rear of the VCR.

3Plug the other end into the appropriate connector on the television.

10

11

Connecting Your VCR to a Satellite Receiver or Other Equipment

B

You can connect your VCR to a Satellite receiver or other VCR using the SCART cable if the appropriate outputs are available on the equipment chosen. The following illustrations give a few examples of the connection possibilities.

1. AV1(EURO AV): By means of 21-pin Scart Cable

Plug the SCART Cable with satellite receiver or other equipment into the AV1(EURO AV) socket on the rear of the VCR.

After making this connection, select the source by pressing the INPUT button for the AV1 input sources.

2. By means of RF Coaxial Cable

After making this connection, you must preset the station received through the satellite tuner.

RF output channel of the satellite receiver should be adjusted away from channel 60, which is used by the VCR, e.g. re-adjust to channel 65.

Aerial

Satellite Receiver or other Equipment

 

2

TV

 

AV2 IN

1

AV1(EURO AV)

 

 

SCART Cable

1. AV2 IN: By means of 21-pin Scart Cable (SV-633B/SV-630B/SV-6303B Only)

Plug the SCART Cable with satellite receiver or other equipment into the AV2 IN socket on the rear of the VCR. After making this connection, select the source by pressing the INPUT button for the AV2 input sources.

2. By means of RF Coaxial Cable

After making this connection, you must preset the station received through the satellite tuner.

RF output channel of the satellite receiver should be adjusted away from channel 60, which is used by the VCR, e.g. re-adjust to channel 65.

Aerial

Satellite Receiver or other

 

 

Aerial Connector

2

TV

SCART Cable

1

OUT

R

AV2 IN

AUDIO

L

TV

AV1(EURO AV)

SCART Cable

12

Connecting the Audio Output Cable (SV-633B/SV-630B/SV-6303B Only)

You can connect your VCR to a Hi-Fi system.

Example: You wish to take advantage of the quality of your Hi-Fi

 

stereo system when watching a programme or recording

 

via your VCR.

Regardless of the type of connection chosen, you

 

must always connect the coaxial cable supplied.

 

Otherwise, no picture will be visible on the screen

 

when the VCR is switched off.

Make sure that both the television and the VCR are switched off before connecting the cables.

1Connect the coaxial cable or SCART as

2Plug the audio output cable into the of your VCR.

Respect the colour coding of the

3Plug the other end of the audio cable connectors on your Hi-Fi stereo system.

GB

OUT

R

AUDIO

L

1

 

2

 

OUT

 

R

AV2 IN

AUDIO

 

L

TV

1(EURO AV)

2

Plug & Auto Set Up

Your VCR will automatically set itself up when it is plugged into the mains for the first time. TV stations will be stored in memory. The process takes a few minutes. Your VCR will then be ready for use.

1Connect the coaxial cable as indicated (Connecting Your VCR to the TV Using

2Plug the VCR into the mains. It will store TV stations in the memory.

3The process will finish after a few minutes. Then the VCR automatically switches itself off.

Now, you only have to switch the VCR on and it is ready for use.

Function for “Plug & Auto Set Up” is fixed already.

So if you want to change this fixed one, you can change it by Presetting the Stations Automatically in OSD “ Auto Set Up” menu. (see page 17)

TV

OUT

R

AUDIO

L

2

13

Tuning Your Television for the VCR

B

STANDBY/ON

EJECT

2

Q-PRO

IPC

4

OK

You must tune your television for the VCR only if you are not using a Scart cable

To view pictures from your VCR when a Scart cable is used, the television must be set to the audio/video mode (AV).

1Switch on the television.

2Switch on the VCR by pressing STANDBY/ON on the front of the VCR or STANDBY/ON on the remote control.

3Select a programme position on the television to be reserved for use with your VCR.

4Insert the video cassette in the VCR. Check that the VCR starts reading the cassette; if not, press II button.

5Start a scan on your television or set the television to UHF channel 60.

6Fine tune the television until the pictures and sound are obtained clearly.

7If you cannot find the pictures and sound, or there is interference from nearby channels, it may be necessary to change the setting of the VCR output channel (see Setting the VCR Output Channel on page 16 and Problems and Solutions on page 41).

8When the picture and sound are perfectly clear, store this channel at the desired programme position on the television.

Result: That programme is now reserved for use with your VCR.

14

Loading...
+ 16 hidden pages