SSM-D1000 Manual
ITEM Bluetooth Module
MODEL NAME SSM-D1000
DESCRIPTION Bluetooth V3.0
SOLUTION CSR: BC57E687C-GITB-E4
SAMSUNG P/N 4709-002101
GoerTek P/N
Green Procurement
Vendor Code
Registration Date
DRAWING CHECK AGREEMENT APPROVAL
A TERM OF VALIDITY OVER AT LEAST 15-YEARS FROM ISSUED DATE
Indemnification
Goertek will indemnify, hold harmless, and at Sa msung's request, defend Samsun g and Samsung' s
directors, officers, employees, agents and independent contractors from and against any loss, cost,
liability or expense ( including court cos ts and reasonable fees of attorneys and other
professionals) arising out of or resulting from any third party claim that any Products and/or
Components provided by Goe r te k infringes patent, copyright, trade secret right or other
intellectual property right. If Goertek receives notice of an alleged patent, copyright, trade secret
or other intellectual property ri g ht infringement or if Samsung's use of the Products and/or the
Components provided by Goer te k shall be prevented by permanent injunction for reasons of
patent, copyright or trade secret infringement, Goertek may, at its sole option and expense,
procure for Samsung the rig ht to continued use of th e Products and/or the Com ponents as provided
hereunder, or modify the allegedly infringing item such that it is no longer infringing, or replace
the allegedly infringing item.
MAKER Goertek TEL
ADDRESS
Dongfang North Road, New&High-tech Industrial
development Zone, Weifang, Shandong, China
Part _ Specification
1. Introduction
SSM-D1000 is a BT module compliant with Bluetooth 3.0 standard. The core chipset is from CSR,
part number is BC57E687C-GITB-E4.
2. Features
Chipset: CSR BC05;
Interface: 8Pin connect with Audio Dock main board
Power supplier: Smart phone Audio Dock Board (3.3 V)
Weight: 4g
Capsule Dimensions: 50mm (L) * 24mm(W) * 7mm(T)
Available distance: 10m
3. Hardware Architecture:
3.1 Main Chipset Information
Item Vender Part number
Bluetooth T rans ceive r/PA CSR BC57E687C-GITB-E4
Figure 1-1 BC57E687C-GITB-E4 Chip Block Diagram
3.2 Circuit Block Diagram
The major internal components and ext ernal interfaces of SSM-D1000 are illustrated in Figure 1-2.
Figure 1-2 SSM-A1000 Major Component and System Interface
4. Interface definition
5. Specifications:
5.1 Supply Voltage:
3.3V±5% DC
5.2 Current Consumttion
Status Current consumption
Power on with no pair 4.1 mA
When pairing 20 mA
When playing music 23.4 mA
Current Consumption of DUT
.
6. Environmental Spec.
Operating Temperature Range: -10degree C~ 60degree C
Storage Temperature Range: T emperature: -20～80℃ Humidity: 95％(MAX)
Operating Humidity Range: 10%～90％ (No dew condensation)
7. Notice
FCC :
This device complies with Part 15 of FCC Rules. Operation is Subject to following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received including interference that cause undesired
operation.
This equipment has been teste d a nd found to comply within the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, i f not inst alled and used in
accordance with the instructions, m ay caus e ha rmful interference to radio communica ti ons. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determ ined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a different circuit from that to which the receiver is connected
• Consult the dealer or an experienced radio/TV technician f or h elp.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure li mits set forth for an uncontrolled environment.
IMPORTANT NOTE:
This module is intended for OEM integrator. The OEM integrator is still responsi ble for the FCC
compliance requirement of the end pr od uct, which in te grates this module.
Any changes or modifications not expressly approved by the manufacturer could void the user's authority
to operate this equipment.
LABEL OF THE END PRODUCT
The final end product must be labeled in a visible area with the following " Contains FCC ID:
A3LSSMD1000".
If the size of the end product is larger than 8x10cm, then the following FCC part 15.19 statement has to
also be available on the label: This device com plies with Part 15 of FCC rules. O peration is subject to the
following two conditions: (1) this device may not cause harmful interference and (2) this device must
accept any interference received, including interference that may cause undesired ope ration.
IC Statement
This Class B digital apparatus complies with Canadian ICES-003.
Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired operation of
the device.
Cet appareil numérique de la classe B est conforme á la norme NMB-003 du Canada.
This device and its antenna(s) must n ot be co-located or operation in conjunction with any other antenna
or transmitter.
LABEL OF THE END PRODUCT
The final end product must be labeled in a visible area with the following "Contains IC :
649E-SSMD1000".
Loading...