Samsung SRD-880D, SRD-1680D User Manual

8 CHANNEL/ 16 CHANNEL DVR

User Manual

SRD-1680D/880D

8 Channel/ 16 Channel DVR

User Manual

Trademark

The name of this product is the registered trademark of Samsung Techwin Co., Ltd. Other trademarks mentioned in this manual are the registered trademark of their respective company.

Restriction

Samsung Techwin Co., Ltd shall reserve the copyright of this document. Under no circumstances, this document shall be reproduced, distributed or changed, partially or wholly, without formal authorization of Samsung Techwin.

Disclaimer

Samsung Techwin makes the best to verify the integrity and correctness of the contents in this document, but no formal guarantee shall be provided. Use of this document and the subsequent results shall be entirely on the user's own responsibility. Samsung Techwin reserves the right to change the contents of this document without prior notice.

Design and specifications are subject to change without prior notice.

The default administrator ID is “admin”, and the password must be set when the user log in at the first time.

Set password for your wireless net work if you use the pr oduct with a wireless router. Being not protected with password or using the

fault wireless router password may expose your video data to potential threat .

de To prevent from your per sonal information being exposed, please change your password every 3 months . Note that the security and

her related issues caused by careless management of password shall be be in the charg e of the user.

is the registered logo of S amsung Techwin Co., Ltd.

● overview

overview

IMPORTANT SAFETY INSTRUCTIONS

Read these operating instructions carefully before using the unit. Follow all the safety instructions listed below. Keep these operating instructions handy for future reference.

Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings, Install in accordance with the manufacturer’s instructions.

8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9) Do not defeat the safety purpose of the polarized or grounding- type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. if the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11) Only use attachments/accessories specified by the manufacturer.

12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13) Unplug this apparatus during lightning storms or when unused for long periods of time.

14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

English _3

overview

BEFORE START

This manual provides operational information necessary for using the product and contains a description about each component part and its function as well as menu or network settings. You have to keep in mind the following notices :

• SAMSUNG retains the copyright on this manual.

• This manual cannot be copied without SAMSUNG’s prior written approval.

• We are not liable for any or all losses to the product incurred by your use of non-standard product or violation of

instructions mentioned in this manual.

• Prior to opening the case, please consult a qualified technician first. Whenever this is needed power must be removed from the unit.

• Before installing additional HDD or connecting the SATA device to this product, check if it is compatible with the product.

Warning

Battery

It is essential that when changing the battery in the unit, the replacement battery must be of the same type otherwise there may be a possibility of an explosion. The following are the specifications of the battery you are using now.

• Normal voltage : 3V

• Normal capacity : 220mAh

• Discharge Current : 0.2mA

• Operating temperature : -20°C ~ +85°C

(-4°F ~ +185°F)

CALIFORNIA USA ONLY

This Perchlorate warning applies only to primary CR (Manganese Dioxide) Lithium coin cells in the product sold or distributed ONLY in California USA.

“Perchlorate Material - special handling may apply, See www.dtsc.ca.gov/hazardouswaste/perchlorate.”

Caution

• Connect the power cord into a grounded outlet.

• The Mains plug is used as a disconnect device and shall stay readily operable at any time.

• Batteries shall not be exposed to excessive heat such as sunshine, fire or the like.

• Risk of Explosion if Battery is replaced by an Incorrect Type. Dispose of Used Batteries According to the

Instructions.

System Shutdown

Turning off the power while the product is in operation, or undertaking improper actions may cause damage or malfunction to the hard drive or the product. To safely cut off power, press the front Power button on the product to display the confirmation message. Click <OK> and then unplug the power cable. You may want to install a UPS system for safe operation in order to prevent damage caused by an unexpected power stoppage. (Any questions concerning UPS, consult your UPS retailer.)

4_ overview

● overview

Operating Temperature

The guaranteed operating temperature range of this product is 0°C ~ 40°C (32°F ~ 104°F). This product may not work properly if you run right after a long period of storage at a temperature below the guaranteed one. Prior to using a device that has been stored for a long period in low temperatures, allow the product to stand at room temperatur Especially for the built-in HDD in the product, its guaranteed temperature range is 5°C ~ 55°C (41°F ~ 131°F). Likewise, the hard drive may not work at a temperatur

e for a period.

e below the guaranteed one.

Ethernet Port

This equipment is in door use and all the communication wirings are limited to inside of the building.

Security Precautions

The default administrator ID is “admin”, and the password must be set when the user log in at the first time. Set password for your wireless network if you use the product with a wireless router. Being not protected with pa

ssword or using the default wireless router password may expose your video data to potential threat. To prevent from your personal information being exposed, please change your password every 3 months. Note that the security and other related issues caused by careless management of password shall be be in the charge of the user.

English _5

overview

CONTENTS

OVERVIEW

INSTALLATION

CONNECTING WITH OTHER DEVICE

3 Important Safety Instructions 4 Before Start 6 Contents 8 Features 10 Part Names and Functions (Front) 12 Part Names and Functions (Rear) 14 Remote Control

16 Checking the installation environment 17 Rack Installation 17 Installing The HDD

20 Connecting External Devices 23 Connecting the Network

6_ overview

LIVE

MAIN MENU

25 Getting Started 28 Live Screen Configuration 33 Live Mode 35 Spot Out 36 Zoom 36 Audio ON/OFF 36 Freeze 37 Event Monitoring

38 System Setup 48 Setting the Device 58 Setting the Recording 61 Setting the Event 64 Backup 66 Network Configuration 79 Controlling a PTZ device

● overview

SEARCH & PLAY

82 Search 85 Playback

WEB VIEWER

BACKUP VIEWER

117

APPENDIX

119

87 Introducing Web Viewer 88 Connecting Web Viewer (Windows) 90 Using Live Viewer (Windows) 95 Controlling a Connected PTZ Camera 98 Using Search Viewer 101 Viewer Setup 112 About 113 Connecting Web Viewer (Mac) 114 Using Live Viewer (Mac) 116 Mobile Viewer

117 SEC Backup Viewer

119 Product Specification 122 Product Overview 124 Default Setting 127 Troubleshooting 130 Open Source Announcement

English _7

overview

FEATURES

This product can compress 8-channel or 16-channel camera input into a H.264 video clip, or compress 8-channel

HD-SDI input or 8-channel composite input, and record in HDD and replay the video at the same time.

These DVRs also supports network connectivity, providing remote monitoring from a remote PC transferring video

and audio data.

• Provides a convenient User Interface

• 8/16 CH Composite Input Connectors

• HD(CH1~8): Supports CIF/2CIF/4CIF/WD1/HD recording

• SD(CH1~8/9~16): Supports CIF/2CIF/4CIF/WD1 recording

` You can only choose either HD or SD for CH1-8.

• With the network specific codec, network transfer enabled regardless of the recording conditions

• Display of HDD information and status by using HDD SMART

• HD CODEC performance: 8CH Full HD 240IPS(NTSC)/200IPS(PAL)

• SD CODEC performance: 8CH SD: 240IPS(NTSC)/200IPS(PAL)

16CH SD: 480IPS(NTSC)/400IPS(PAL)

• HDD overwrite function

• Mass storage HDD backup through high-speed USB 2.0

• Simultaneous Record and Playback of 8/16-channel video data

• Various Search Modes (Time, Event, Backup, POS, Motion Detection)

• Various Recording Modes (Manual, Event, Scheduled Recording)

• Alarm Interface

• Remote Monitoring function by Network Viewer, Smart Viewer and Mobile Viewer

• Supports coaxial protocols(SD Channel only)

• Tampering Detection

8_ overview

Standards Approvals

` This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the

FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Package Contents

Please unwrap the product, and place the product on a flat place or in the place to be installed. Please check the following contents are included in addition to the main unit.

USB

DVR Power Cable

● OVERVIEW

Mouse User Manual or Quick Manual

Network Viewer Software /

User Manual CD

Bracket Fixing Screw Bracket Rack HDD Fixing Screw

Terminal Block (15 pin) Terminal Block (20 pin)

Remote Control /

Remote Control Battery (AAA)

English _9

overview

PART NAMES AND FUNCTIONS (FRONT)

SRD-880D

SRD-1680D

Part Names Functions

Channel Used to select channel numbers directly in the Live Mode, or numbers in the numeric input mode.

cb d e

USB

cb d e

USB

REC Starts or ends the recording.

&/(

+/# Play/Pause : Used to pause or resume the screen.

)/*

LED Indicator

Direction / Select Button

Jog shuttle

10_ overview

Step Rewind (& Fast Rewind (() : Used for quick backward search while in Play. (2x-64x)

Stop : Used to stop the playback.

Fast Forward ()) : Used for quick forward playback. (2x-64x) Step Forward (

REC : Lights on when recording is in progress.

HDD : Displays the normal access to HDD.

Upon access to HDD, LED repeats on and off.

ALARM :

NETWORK : Displays both network connection and data transfer status.

POWER : Displays the power ON/OFF status.

Used to change a value or move the cursor up/down/left/right (▲▼_ +). Selects a menu item or executes the selected menu.

When a scroll bar appears in each menu, acts as a scrolling. In Play mode, - Jog : Pauses the playback and steps backward or forward.

) : Used for backward frame-by-frame search while in PAUSE.

*) : Used for forward frame-by-frame search while in PAUSE.

Lights on when an event occurs.

- Shuttle : Fast playback forward or backward.

● overview

Part Names Functions

Power

USB Port 1 / 2 Connects the USB devices.

Used to turn the DVR ON/OFF.

` Functions only if the button was held for 2 seconds.

MODE

AUDIO Sets Audio ON/OFF.

ALARM Cancels the ALARM LED and the audible alarm when the alarm is going off, and to remove the icon.

MENU/' Either goes to the system menu screen or moves to the upper menu from the lower menu.

ENTER Runs selected menu function.

Camera Control

OPEN/CLOSE Used to open and close the DVR-RW disc tray.

Using the jog shuttle

` Jog starts from the right point and shuttle starts from the left point.

< Jog >

Each time you press the button in Live mode, the screen mode will be switched in sequence. Each time you press the button in play mode, the screen mode will be switched in sequence.

ZOOM : Sets the screen to the x2 digital zoom.

FREEZE : Runs the FREEZE function in the Live Mode.

BACKUP : Runs the BACKUP function.

SEARCH : Goes to the search screen.

In play mode, DVR playback steps forward video by 1 frame. In play mode, DVR playback steps backward video by 1 frame.

< Shuttle >

In play mode, DVR plays fast forward. In play mode, DVR plays fast reverse.

English _11

overview

PART NAMES AND FUNCTIONS (REAR)

CH1 CH2

CH3 CH4

AUDIO OUT

VGA OUT

CONSOLE

HDMI

eSATA

NETWORK

SPOT 2

SPOT 1

COM COM COM COM

NCNO NO NO

2 3 4

SERIAL

1 2 3 4 5 6 7 8 9

10 11 1213 14 15 16

SRD-880D

SRD-1680D

SPOT 1

eSATA

10 11 1213 14 15 16

eSATA

VGA OUT

SERIAL

NETWORK

VGA OUT

SERIAL

NETWORK

CH1 CH2

CH3 CH4

SPOT 2

CH1 CH2

CH3 CH4

SPOT 2

AUDIO OUT

NCNO NO NO

COM COM COM COM

NCNO NO NO

COM COM COM COM

2 3 4

CONSOLE

HDMI

i h g

1 2 3 4 5 6 7 8 9

CONSOLE

HDMI

i h g

Part Names Functions

SPOT1/2 BNC type of output port for the Spot signal.

AUDIO IN Audio input signal port (RCA jack) and port for optional audio extension cable.

AUDIO OUT Audio Signal Output Port (RCA jack).

VGA OUT Composite Video Signal Output Port (VGA type connector).

Power Power connection port.

SERIAL Serial port for connecting to a POS device.

NETWORK NETWORK connector port.

eSATA Ports used for external storage device connections.

HDMI HDMI connector port.

12_ overview

● overview

Part Names Functions

- ALARM IN : Alarm Input port. SRD-880D: 1~

ALARM

VIDEO IN Video Signal Input Port (BNC type connector).

` [CONSOLE] is designed for the service repair purpose only.

SRD-1680D : 1~16 CH

- ALARM RESET : Alarm Reset port.

- ALARM OUT 1~4 : Alarm Output port.

8 C H

English _13

overview

REMOTE CONTROL

Displays the search menu.

Changes the screen mode.

Displays the Exit pop up screen.

Used as the numeric input keys, or displays a single

Skip Backward (by unit time),

Slow Rewind, Slow Forward,

Skip Forward (by unit time)

Goes to the system menu screen.

Up/Down/Left/Right(

Moves the cursor up/down/left/right, and runs the Select

Freezes the screen temporarily.

Runs the digital zoom (x2) function.

Starts or ends the live recording.

Runs the View function in the PTZ mode.

MODE

POWER

NUMBER [0~+10]

channel.

T/W

Zooms in or out.

▲▼_ +

)/ENTER

Menu.

FREEZE

ZOOM

REC

VIEW

BACKUP

Displays the Backup Menu.

OPEN/CLOSE

Opens or closes the DVD tray.

DVR

Activates the DVR function.

Sets the ID of the system. Select 2 digits from 0 ~ 9 while pressing the ID Key.

Move Frame

While paused, moves to the previous/next frame.

FR, STOP, PLAY/PAUSE, FF

PTZ

Displays or ends PTZ.

SCROLL

Moves the menu scroll.

RETURN

Returns to the previous screen.

AUDIO

Turns Audio on/off.

ALARM

Cancels the Alarm.

REC LOCK

Selects the recording lock function.

PRESET

Displays the Preset Setup.

14_ overview

● overview

Using the Numeric buttons

CHANNEL 1–9 Press each button between 1 to 9.

CHANNEL 10 Press the [+10] button first, then press the 0 button again within 3 seconds.

CHANNEL 11–16 Press the [+10] button first, then press any number between 1 to 6 within 3 seconds.

Changing the Remote Control ID

Remote control’s ID and DVR’s ID should be matched for proper operation.

1. Press the [ID] button of the remote control and check the ID displayed on the DVR screen.

The factory default ID of the remote control is 00.

Enter 2 digits of your selection in order, while pressing the [ID] button of the remote control.

3. When ID input is done, press the [ID] button of the remote control again to check the setting.

` If you want to change the remote control ID to 08: Press 0 and 8 in order while the [ID] button of the remote control is

pressed. For changing the ID of remote device, refer to “Remote Devices”. (Page 54)

English _15

installation

USB

DVD RECORDER

USB

DVD RECORDER

Please take note of the followings before using this product.

• Do not use the product outdoor.

• Do not spill water or liquid in the connection part of the product.

• Do not impose the system to excessive shock or force.

• Do not pull out the power plug forcefully.

• Do not disassemble the product on your own.

• Do not exceed the rated input/output range.

• Use a certified power cord only.

• For the product with an input ground, use a grounded power plug.

CHECKING THE INSTALLATION ENVIRONMENT

This product is a top-notch security device that is equipped with a high-capacity HDD and other key circuit boards.

Temperature Unit: ºC

One Year: 24HR X 365 DAY =8,760 HR

When the temperature rises inside the product, the product may breakdown and the product life be shortened. Please pay attention to the following recommendations before installation.

Life (Unit: HOURS)

[Figure 1]

When mounting the product on a rack, comply with the following instructions.

1. Please ensure that the rack inside is not sealed.

2. Please ensure the air is circulated through the inlet/outlet as shown in the picture.

3. If you pile up the prudcts or other rack-mount devices as shown in figure 2, secure

room for ventilation or install a vent. For natural air convection, place the inlet at the bottom of the rack and the outlet on top.

5. It is strongly recommended that a fan motor is installed at the inlet and the outlet for

air circulation. (Please fit a filter at the inlet to screen dust or foreign substances.)

6. Please maintain the temperature inside the rack or surrounding areas between 0°C

~ 40°C (32°F ~ 104°F) as shown in the figure 1.

Rack Mount Instructions - The following or similar rack-mount instructions are included with the installation instructions :

A) Elevated Operating Ambient - If installed in a closed or multi-unit rack assembly, the

operating ambient temperature of the rack environment may be greater than room

DVD RECORDER

USB

ambient. Therefore, consideration should be given to installing the equipment in an environment compatible with the maximum ambient temperature (Tma) specified by the manufacturer.

B) Reduced Air Flow - Installation of the equipment in a rack should be such that

the amount of air flow required for safe operation of the equipment is not compromised.

C) Mechanical Loading - Mounting of the equipment in the rack should be such

that a hazardous condition is not achieved due to uneven mechanical loading.

D) Circuit Overloading - Consideration should be given to the connection of the

equipment to the supply circuit and the effect that overloading of the circuits might have on overcurrent protection and supply wiring. Appropriate

[Figure 2]

consideration of equipment nameplate ratings should be used when addressing this concern.

E) Reliable Earthing - Reliable earthing of rack-mounted equipment should be maintained. Particular attention should

be given to supply connections other than direct connections to the branch circuit (e.g. use of power strips).

16_ installation

● installation

RACK INSTALLATION

Install the Bracket-Rack as shown in the figure, and then fasten the screws on both sides (2 screws on each side).

` Remove the screws on the left and right side of the DVR before installation.

` Fix the screws not to be loosened by vibrations.

Cautions when Installing in the Rack

To install multiple DVRs in the rack, make sure to separate the FOOT at the bottom of each DVR.

1. There are four FOOTs at the bottom of a DVR.

Press the projected parts at both-ends of each “ and turn it counterclockwise.

2. “FOOT” is separated from the main body when it is turned

to the end of fastening groove.

FOOT”

INSTALLING THE HDD

Make sure to unplug the power cord from the wall outlet to prevent possible electric shock, injury or product damage. Please consult your provider for further information on HDD installation since improper installation or settings may damage the product.

` Make sure to unplug the power cord from the wall outlet before proceeding with the installation.

` Cautions for data loss (HDD care)

Please pay attention so that the data inside the HDD is not damaged. Before adding a HDD, please check the compatibility with this product. HDD is vulnerable to malfunction due to its sensitive nature especially against shock when operating. Please ensure that the HDD is free from such shock. We are not liable for any damage to the HDD incurred by user’s carelessness or miss use.

` Cases might cause damage to HDD or recorded data

To minimize the risk of data loss from a damaged HDD, please backup data as often as possible. If exposed to shock when disassembling or installing, data stored in the hard disk may be damaged. A sudden power failure or turning off the product while in HDD operation may damage the hard disk drive. HDD or files stored inside may be damaged if the main body is moved or impacted during the HDD operation.

English _17

installation

Cautions on HDD installation

1. When adding a new HDD, make sure to fasten screws tightly and use appropriate parts if required to fix

the HDD. Otherwise, the product may be damaged or does not operate properly.

2. Please check the HDD compatibility before adding a HDD.

` Please contact your nearest dealer to obtain the list of compatible devices.

Installing the HDD

` If the installed HDD had been used with other devices, it will be automatically formatted.

• Installing HDD by opening the cover

1. Pulling the front cover from the unit.

2. Remove the screws from the bracket safety.

3. Separate the HDD bracket by pushing the lock on the left.

` Be careful not to scratch the hand while separating the HDD

bracket.

Bracket safety

18_ installation

● installation

4. Attach the HDD onto the bracket, and fasten the screws

on both sides to fix it.

5. Align the bracket with installed HDD to the guide of the

case, push it toward the board.

6. You can check the HDD map directly on the DVR. Refer to “Storage

Device > HDD Map”. (Page 51)

7. Attach the bracket safety and fasten the screws.

Bracket safety

English _19

connecting with other device

CONNECTING EXTERNAL DEVICES

` The following figures are based on Model SRD-1680D.

AUDIO OUT

AC 100-240V~IN

VIDEO IN

AUDIO IN AUDIO IN

CH1 CH2

CH3 CH4

SPOT2

AUDIO OUT

NCNO NO NO

COM COM COM COM

2 3 4

HDMI

SPOT 1

SPOT 2

SPOT1

CONSOLE

VIDEO OUT

1 2 3 4 5 6 7 8 9

HDMI

(VGA)

10 11 1213 14 1516

eSATA

VGA OUT

SERIAL

NETWORK

eSATA HDD

HD-SDI Video Cable

The cable connecting the DVR’s HD-SDI video input and a camera is a BNC coaxial cable as shown below.

If the distance between the DVR and the camera exceeds the recommended maximum,

please us an auxiliary video amp.

Maximum video transfer distance Recommended cable specification

100~140m 5C2V(75ohm)

200m

L-6CHD(75ohm)

(SDI-specific Cable)

Connecting the USB

1. By factory default, a USB port is provided for external connection.

2. You can connect a USB HDD, USB CD/DVD player, USB memory or mouse to the USB port.

If a USB HDD is connected to the system, recognition and settings are available in “Main Menu >

Storage Device”. (Page 51)

4. The product supports hot plugging function that enables connecting/disconnecting USB devices while in

operating the system.

` If the USB storage media for backup is not formatted by the product, format it as FAT32 file system with a PC.

` To prevent from USB ports being damaged, please unplug USB devices before openning the front cover.

20_ connecting with other device

Device

● connecting with other device

Connecting External SATA HDD (eSATA)

External SATA port is provided on the rear panel. If connected to the system, the external SATA HDD (eSATA) can be recognized and configured in “Main Menu > Device > Storage Device”.

` Use a cable shorter than 1 m for the external external SATA HDD (eSATA) connections.

` Unexpected disconnection to a device in use which is connected via eSATA may restart the system. Check whether the

device is in use before disconnecting it.

Connecting POS Device

You can connect a POS device to the RS-232C port on the product’s rear side when you connect it directly with a RS-232C cable. Connection setup for the RS-232C port is available in “ <

POS Device Setup> button and set <Baudrate, Parity, Data, Stop bit>. (Page 55)

Main Menu > Device > POS Devices”, press the

Connecting the Alarm Input/Output

The Alarm In/Out port at the back is composed of the following.

SRD-880D

• ALARM IN 1 ~ 8 : Alarm Input Port

• ALARM RESET : On receiving an Alarm Reset signal, the system cancels the current Alarm Input and

resumes sensing.

• ALARM OUT 1 ~ 4 : Alarm Output Port

ALARM OUT

(30VDC 2A,

125VAC 0.5A MAX)

VGA OUT

Sensors

Alarm

ALARM IN (5mA sink)

English _21

connecting with other device

SRD-1680D

VGA OUT

Sensors

Alarm

• ALARM IN 1 ~ 16 : Alarm Input Port

• ALARM RESET : On receiving an Alarm Reset signal, the system cancels the current Alarm Input and

resumes sensing.

• ALARM OUT 1 ~ 4 : Alarm Output Port

ALARM OUT

VDC 2A,

(30

125VAC 0.5A MAX)

ALARM IN (5mA sink)

22_ connecting with other device

Connecting the RS-485 Device

Connect the [TX/RX +, –] device through the back port.

` You can connect and control the PTZ camera which supports the RS-485 communication.

` Check if the RS-485 device is compatible with the product first.

` Pay attention not to change the polarity (+/-) of the RS-485 device when connecting it.

` Depending on camera’s type, connection polarity can be different.

For further information, refer to the respective PTZ Camera’s documentation.

CONNECTING THE NETWORK

VGA OUT

● CONNECTING WITH OTHER DEVICE

system keyboard

PTZ camera

Connecting to Network through Ethernet (10/100/1000BaseT)

Back Bone

RJ-45 Ethernet Cable (Direct Cable)

Network Viewer

Hub/Switcher

Windows

VGA OUT

NETWORK

Hub/Switcher

English _23

connecting with other device

Connecting to the Network using the router

VGA OUT

Broadband Router

xDSL or Cable Modem

NETWORK

Connecting to Network through PPPoE

VGA OUT

Phone(PPPoE) Line

NETWORK

xDSL or Cable Modem

RJ-45 Ethernet Cable (Dir

ect Cable)

Network Viewer

External Remote PC

DDNS Server (Data Center)

PPPoE MODEM

Windows

her

Hub/Switc

24_ connecting with other device

● live

live

2013-01-01 01:10:25

GETTING STARTED

Starting the system

1. Connect power cable to the product’s rear.

2. Touch and hold the front power button for over 3 seconds.

` It takes about 10 seconds to display the start screen after

booting.

3. The boot up screen appears. Booting up may take about 3 minute, as indicates

ogress with icons.

pr If a new HDD is installed, the initialization process may take longer.

REC

4. The live screen appears with a beep.

English _25

live

Shutting Down the System

2013-01-01 01:10:25

You can shut down the system only if you have logged in to the DVR. You require permission to shut down the system if you are not logged in as admin.

1. Hold the [POWER] button on the front or the remote

control for over 3 seconds, or right click and click <Shutdown>.

2. The “Shutdown” confirmation window appears.

Shutdown

3. Use the arrow keys on the remote control or the front panel to move to <OK> and press the [ENTER] button or click <OK>. The system will shut down.

` For the permission management, refer to “Permission

Management > Setting Permissions”. (Page 43)

To access a DVR or restricted menu, you should have logged in to the DVR.

1. In live mode, right-click any area of the screen. You will see the context sensitive menu as in the right figure.

Are you sure to shutdown?

OK Cancel

Scene Mode

Spot Out 1

Spot Out 2

Audio Off

Freeze

Stop Alarm

Record

Play

Backup

Main Menu

Shutdown

Hide Launcher



26_ live

Click <Login>.

The login dialog appears. You can also see the login dialog to access a desired menu by pressing the [ control or the front panel.

` The login dialog will also appear if you press a menu button on the

MENU] button on the remote

ID admin



Password



remote control or the front panel of the DVR when the corresponding menu requires logging in.

` After logged in, press [RETURN] on the remote control to display the

logout dialog.

` For the restricted permission, refer to “Permission Management > Setting Permissions”. (Page 43)

OK Cancel

● live

` The default administrator ID is “admin”, and the password must be set when the user log in at the first time.

2013-01-01 01:10:25

` Set password for your wireless network if you use the product with a wireless router. Being not protected with password or

using the default wireless router password may expose your video data to potential threat.

` To prevent from your personal information being exposed, please change your password every 3 months.

` Note that the security and other related issues caused by careless management of password shall be be in the charge of the

user.

Locking All Buttons

This will restrict access to all buttons available in the DVR.

1. In Live mode, press buttons in the order of [STOP (@)] FREEZE][STOP (@)][FREEZE][MENU].

[ <All Key Lock> confirmation window appears.

2. Select <OK>.

All keys are locked.

In the lock condition, press any button to display a dialog

where you are prompted to enter the password for unlocking the buttons. The button lock will be released if you enter the admin password.

All Key Lock

Are you sure to all key lock?

OK Cancel

English _27

live

LIVE SCREEN CONFIGURATION

Icons on the Live Screen

You can check the status or operation of the DVR with the icons on the live screen.

a b

CAM 01

Part Names Functions

Current Date, Time Displays the current time and date.

Displayed if the recording is in process.

` To cancel the recording, enter the password.

Displayed if the zoom function is activated.

Screen Mode

Displayed if you press the Pause button.

a b c

2013-01-01 01:10:25

28_ live

System

Operation

Displayed in Auto Sequence mode where all channels are switched at the specific time interval.

Displayed if there is a problem with the cooling fan.

Displayed if the HDD is full and the DVR has an insufficient space to record.

Displayed if no HDD is installed or the existing HDD should be replaced.

Displayed if the HDD needs a technical examination.

Displayed while the backup is in process or if the backup data is played.

Displayed if a new firmware is found from the network.

● live

Part Names Functions

2013-01-01 01:10:25

Video Input

Status

Camera Name/ Channel Displays the camera name and the changed channel, if any.

Displayed if no input is entered in the condition that the camera is set to <ON>.

Nothing will be displayed on the screen if the camera is set to <OFF>.

Displayed in PTZ setting, and highlighted yellow if PTZ is in operation.

Displays AUDIO ON/MUTE. Not displayed in video mode if deactivated.

If the sensor is set to <ON>, the input signal will be displayed on the screen of the

Camera

Operation

connected channel.

Displayed if a motion detected in the condition that the motion detection is set to <ON>.

Appears when the Tampering Detection is set to <ON> and a tampering attempt is detected.

Displays the current record mode from Record/Event/Schedule.

Error Information

• If the internal HDD is not connected, the “NO HDD”( ) message will appear; if there occurs a problem,

you will see the “HDD FAIL”( service center for assistance as this may cause a failure of recording, playback or backup.

• If the cooling fan does not work properly or has a problem, the <Fan Information> window will appear and

the fan error icon (

) will be displayed on the top left corner. In this case, check to see if the internal fan works. As a fan error can shorten the product life, make sure you contact the service center for assistance.

) message in the top left corner. In this case, make sure you contact the

` If you see the fan error icon or No HDD, HDD FAIL icons on the screen, contact the service center for more details.

Live Screen Menu

In addition to the buttons on the front panel or the remote control, you can access a desired menu by rightclicking the mouse any area in live mode. Right click opens the context menu which shows different menu items according to the situation, such as logged in/out state, split screen mode, and various operational conditions.

` Menu items of Search, Record, Backup, Shutdown and PTZ can be deactivated, depending on the user permission.

Scene Mode

Spot Out 1

Spot Out 2

Audio Off

Freeze

Stop Alarm

Record

Play

Backup

Main Menu

Shutdown

Hide Launcher

Logout

< Split Mode Menu >



< Single Mode Menu >

Scene Mode

Spot Out 1

Spot Out 2

PTZ Control

Zoom In

Audio

Freeze

Stop Alarm

Record

Play

Backup

Main Menu

Shutdown

Hide Launcher

Logout



English _29

live

Split Mode Menu

2013-01-01 01:10:25

The context sensitive menu in split mode differs, depending on the login/logout status.

Scene Mode

Spot Out 1

Spot Out 2

Audio Off

Freeze

Stop Alarm

Record

Play

Backup

Main Menu

Shutdown

Hide Launcher

Logout



Menu Functions

Scene Mode Refer to “Live Mode”. (Page 33)

Spot Out1/2 Refer to “Spot Out”. (Page 35)

Audio On/Off Refer to “Audio ON/OFF”. (Page 36)

Freeze Refer to “Freeze”. (Page 36)

Stop Alarm Stops the alarm output and the event monitoring. Refer to “Event Monitoring”. (Page 37)

Record/Stop Starts/stops the standard recording.

Play Plays the search result (data). Refer to “Search & Play > Play”. (Page 85)

Search Refer to “Search & Play > Search”. (Page 82)

Backup Refer to “Main Menu > Setting the Backup”. (Page 64)

Main Menu Accesses the main menu. Refer to the Using the DVR section. (Page 38)

Shutdown Turns down the DVR.

Show/Hide Launcher Shows or hides the launcher. Refer to “Show / Hide the Launcher Menu”. (Page 32)

30_ live

+ 117 hidden pages