Samsung SRD-876D-1TB, SRD-1676D-1TB User Manual

8 CHANNEL/ 16 CHANNEL DVR

User Manual

SRD-876D/1656D/1676D

8 Channel/ 16 Channel DVR

User Manual

Tra de mar k

The name of this product is the registered trademark of Samsung Techwin Co., Ltd. Other trademarks mentioned in this manual are the registered trademark of their respective company.

Restriction

Samsung Techwin Co., Ltd shall reserve the copyright of this document. Under no circumstances, this document shall be reproduced, distributed or changed, partially or wholly, without formal authorization of Samsung Techwin.

Disclaimer

Samsung Techwin makes the best to verify the integrity and correctness of the contents in this document, but no formal guarantee shall be provided. Use of this document and the subsequent results shall be entirely on the user's own responsibility. Samsung Techwin reserves the right to change the contents of this document without prior notice.

Design and specifications are subject to change without prior notice.

The default administrator ID is “admin”, and the password must be set when the user log in at the first time.

Set password for your wireless network if you use the product with a wireless router. Being not protected with password or using the default wireless router password may expose your video data to potential threat. To prevent from your per sonal information being exposed, please change your password every 3 months. Note that the securit y and other related issues caused by careless management of password shall be be in the charge of the user.

is the registered logo of S amsung Techwin Co., Ltd.

overview

IMPORTANT SAFETY INSTRUCTIONS

Read these operating instructions carefully before using the unit. Follow all the safety instructions listed below. Keep these operating instructions handy for future reference.

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings, Install in accordance with the manufacturer’s instructions.

8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9) Do not defeat the safety purpose of the polarized or grounding- type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. if the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11) Only use attachments/accessories specified by the manufacturer.

12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13) Unplug this apparatus during lightning storms or when unused for long periods of time.

14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

● OVERVIEW

English _3

overview

BEFORE START

This manual provides operational information necessary for using the product and contains a description about each component part and its function as well as menu or network settings. You have to keep in mind the following notices :

• SAMSUNG retains the copyright on this manual.

• This manual cannot be copied without SAMSUNG’s prior written approval.

• We are not liable for any or all losses to the product incurred by your use of non-standard product or violation of

instructions mentioned in this manual.

• Prior to opening the case, please consult a qualified technician first. Whenever this is needed power must be removed from the unit.

• Before installing additional HDD or connecting the SATA device to this product, check if it is compatible with the product.

Warning

Battery

It is essential that when changing the battery in the unit, the replacement battery must be of the same type otherwise there may be a possibility of an explosion. The following are the specifications of the battery you are using now.

• Normal voltage : 3V

• Normal capacity : 220mAh

• Discharge Current : 0.2mA

• Operating temperature : -20°C ~ +85°C

(-4°F ~ +185°F)

CALIFORNIA USA ONLY

This Perchlorate warning applies only to primary CR (Manganese Dioxide) Lithium coin cells in the product sold or distributed ONLY in California USA.

“Perchlorate Material - special handling may apply, See www.dtsc.ca.gov/hazardouswaste/perchlorate.”

Caution

• Connect the power cord into a grounded outlet.

• The Mains plug is used as a disconnect device and shall stay readily operable at any time.

• Batteries shall not be exposed to excessive heat such as sunshine, fire or the like.

• Risk of Explosion if Battery is replaced by an Incorrect Type. Dispose of Used Batteries According to the

Instructions.

System Shutdown

Turning off the power while the product is in operation, or undertaking improper actions may cause damage or malfunction to the hard drive or the product. To safely cut off power, press the front Power button on the product to display the confirmation message. Click <OK> and then unplug the power cable. You may want to install a UPS system for safe operation in order to prevent damage caused by an unexpected power stoppage. (Any questions concerning UPS, consult your UPS retailer.)

4_ overview

Operating Temperature

The guaranteed operating temperature range of this product is 0°C ~ 40°C (32°F ~ 104°F). This product may not work properly if you run right after a long period of storage at a temperature below the guaranteed one. Prior to using a device that has been stored for a long period in low temperatures, allow the product to stand at room temperature for a period. Especially for the built-in HDD in the product, its guaranteed temperature range is 5°C ~ 55°C (41°F ~ 131°F). Likewise, the hard drive may not work at a temperature below the guaranteed one.

Ethernet Port

This equipment is in door use and all the communication wirings are limited to inside of the building.

Security Precautions

The default administrator ID is “admin”, and the password must be set when the user log in at the first time. Set password for your wireless network if you use the product with a wireless router. Being not protected with password or using the default wireless router password may expose your video data to potential threat. To prevent from your personal information being exposed, please change your password every 3 months. Note that the security and other related issues caused by careless management of password shall be be in the charge of the user.

● OVERVIEW

English _5

overview

CONTENTS

OVERVIEW

INSTALLATION

CONNECTING WITH OTHER DEVICE

LIVE

3 Important Safety Instructions 4 Before Start 6 Contents 8 Features 10 Part Names and Functions (Front) 12 Part Names and Functions (Rear) 14 Remote Control

16 Checking the installation environment 17 Rack Installation 17 Installing The HDD

20 Connecting External Devices 23 Connecting the Network

25 Getting Started 28 Live Screen Configuration 33 Live Mode 35 Spot Out 36 Zoom 36 Audio ON/OFF 36 Freeze 37 Event Monitoring

6_ overview

MAIN MENU

38 System Setup 48 Setting the Device 58 Setting the Recording 61 Setting the Event 64 Backup 66 Network Configuration 79 Controlling a PTZ device

SEARCH & PLAY

82 Search 85 Playback

WEB VIEWER

BACKUP VIEWER

118

APPENDIX

120

87 Introducing Web Viewer 88 Connecting Web Viewer (Windows) 90 Using Live Viewer (Windows) 95 Controlling a Connected PTZ Camera 98 Using Search Viewer 101 Viewer Setup 113 About 114 Connecting Web Viewer (Mac) 116 Using Live Viewer (Mac) 117 Mobile Viewer

118 SEC Backup Viewer

120 Product Specification 123 Product Overview 125 Default Setting 129 Troubleshooting 132 Open Source Announcement

● OVERVIEW

English _7

overview

FEATURES

The product compresses camera inputs from 8/16 channels with H.264 video codec, and supports simultaneous recording and playback of 8/16-channel audio input to/from HDD.

These DVRs also supports network connectivity, providing remote monitoring from a remote PC transferring video and audio data.

• Provides a convenient User Interface

• 8/16 CH Composite Input Connectors

• Supports CIF(S)/2CIF(M)/4CIF(L)/WD1/1280H recording formats

• With the network specific codec, network transfer enabled regardless of the recording conditions

• Display of HDD information and status by using HDD SMART

• CODEC performance : 8CH : 240FPS(NTSC)/200FPS(PAL)

16CH : 480FPS(NTSC)/400FPS(PAL)

• HDD overwrite function

• Mass storage HDD backup through high-speed USB 2.0

• Simultaneous Record and Playback of 8/16-channel video data

• Various Search Modes (Time, Event, Backup, POS, Motion Detection)

• Various Recording Modes (Manual, Event, Scheduled Recording)

• Alarm Interface

• Remote Monitoring function by Network Viewer, Smart Viewer and Mobile Viewer

• Supports coaxial protocols

• Tampering Detection

8_ overview

Standards Approvals

 This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the

FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Package Contents

Please unwrap the product, and place the product on a flat place or in the place to be installed. Please check the following contents are included in addition to the main unit.

USB

DVR Power Cable

● OVERVIEW

Mouse User Manual or Quick Manual

Network Viewer Software /

User Manual CD

Bracket Fixing Screw Bracket Rack

Terminal Block (15 pin) Terminal Block (20 pin)

Remote Control /

Remote Control Battery (AAA)

English _9

overview

PART NAMES AND FUNCTIONS (FRONT)

SRD-876D

 c 

b 

USB

 

SRD-1656D/1676D

 c 

b 

 

Part Names Functions

Channel Used to select channel numbers directly in the Live Mode, or numbers in the numeric input mode.



REC Starts or ends the recording.

) : Used for backward frame-by-frame search while in PAUSE.

) : Used for forward frame-by-frame search while in PAUSE.

/



►/

/

LED Indicator

Step Rewind ( Fast Rewind () : Used for quick backward search while in Play. (2x-64x)

Stop : Used to stop the playback.

Play/Pause : Used to pause or resume the screen.

Fast Forward () : Used for quick forward playback. (2x-64x) Step Forward (

REC : Lights on when recording is in progress.

HDD : Displays the normal access to HDD.

Upon access to HDD, LED repeats on and off.

ALARM : Lights on when an event occurs.

NETWORK : Displays both network connection and data transfer status.

POWER : Displays the power ON/OFF status.



USB



10_ overview

Part Names Functions

Direction / Select Button



Jog shuttle

Power



USB Port Connects the USB devices.



Used to change a value or move the cursor up/down/left/right (◄ ►). Selects a menu item or executes the selected menu.

When a scroll bar appears in each menu, acts as a scrolling. In Play mode, - Jog : Pauses the playback and steps backward or forward.

- Shuttle : Fast playback forward or backward.

Used to turn the DVR ON/OFF.

 Functions only if the button was held for 3 seconds.

● OVERVIEW

MODE

AUDIO Sets Audio ON/OFF.



ALARM Cancels the ALARM LED and the audible alarm when the alarm is going off, and to remove the icon.

MENU/' Either goes to the system menu screen or moves to the upper menu from the lower menu.

ENTER Runs selected menu function.

Camera Control



OPEN/CLOSE Used to open and close the DVR-RW disc tray.



Using the jog shuttle

Each time you press the button in Live mode, the screen mode will be switched in sequence. Each time you press the button in play mode, the screen mode will be switched in sequence.

ZOOM : Sets the screen to the x2 digital zoom.

FREEZE : Runs the FREEZE function in the Live Mode.

BACKUP : Runs the BACKUP function.

SEARCH : Goes to the search screen.

 Jog starts from the right point and shuttle starts from the left point.

< Jog >

In play mode, DVR playback steps forward video by 1 frame. In play mode, DVR playback steps backward video by 1 frame.

< Shuttle >

In play mode, DVR plays fast forward. In play mode, DVR plays fast reverse.

English _11

overview

PART NAMES AND FUNCTIONS (REAR)

SRD-876D

b c 

 

12345678

CH2

VIDEO IN

CH4

LOOP OUT

AUDIO OUT

SERIAL

NCNO NO NO

COM COMCOM COM

G G

12345678

234

+-TX+-

ALARM RESET

ALARM OUT

ALARM IN

NO CONNECTION

AUDIO IN CH5 ~ CH8

NETWORK

CONSOLE HDMIeSATA VGA OUT USB

AUDIO IN

CH1

CH3

SRD-1656D/1676D

b c 

 

16151413121110912345678

NETWORK

AUDIO IN

CH1

CH2

VIDEO IN

CH3

CH4

LOOP OUTAUDIO OUT

SERIAL

+-TX+-

NCNO NO NO

COM COM COM COM

234

ALARM OUT

G GG G

12345678 9

ALARM RESET

ALARM IN

10 11 12 13 14 15 16

AUDIO IN CH5 ~ CH16

CONSOLE HDMIeSATA VGA OUT USB

Part Names Functions

AUDIO IN Audio input signal port (RCA jack) and port for optional audio extension cable.



 m  

b c      

12_ overview

AUDIO OUT Audio Signal Output Port (RCA jack).

VIDEO IN Video Signal Input Port (BNC type connector).

SPOT1/2

BNC type of output port for the Spot signal.

Power Power connection port.

NETWORK NETWORK connector port.

USB Connects the USB devices.

VGA OUT Composite Video Signal Output Port (VGA type connector).

HDMI HDMI connector port.

Part Names Functions

eS ATA Ports used for external storage device connections.



LOOP OUT Terminal used to send the video signal to another device.



- ALARM IN : Alarm Input port. SRD-876D : 1~8 CH SRD-

ALARM



RS-485 Used to establish RS485 communications. (TX+, TX-, RX+, RX-)

SERIAL Serial port for connecting to a POS device.

 [CONSOLE] is designed for the service repair purpose only.

1656D/1676D : 1~16 CH

- ALARM RESET : Alarm Reset port.

- ALARM OUT 1~4 : Alarm Output port.

● OVERVIEW

English _13

overview

REMOTE CONTROL

Displays the Exit pop up screen.

Used as the numeric input keys, or displays a single

Goes to the system menu screen.

Runs the digital zoom (x2) function.

Skip Backward (by unit time),

Slow Rewind, Slow Forward,

Skip Forward (by unit time)

NUMBER [0~+10]

Displays or ends PTZ.

Displays the search menu.

Changes the screen mode.

Displays the Preset Setup.

Freezes the screen temporarily.

POWER

channel.

PTZ

T/W

Zooms in or out.

MODE

PRESET

FREEZE

ZOOM

REC

Starts or ends the live recording.

Sets the ID of the system. Select 2 digits from 0 ~ 9 while pressing the ID Key.

SCROLL ,.

Moves the menu scroll.

VIEW

Runs the View function in the PTZ mode.

BACKUP

Displays the Backup Menu.

RETURN

Returns to the previous screen.

Up/Down/Left/Right(▲▼◄ ►)/ENTER

Moves the cursor up/down/left/right, and runs the Select Menu.

REC LOCK

Selects the recording lock function.

AUDIO

Turns Audio on/off.

ALARM

Cancels the Alarm.

Move Frame

While paused, moves to the previous/next frame.

14_ overview

FR, STOP, PLAY/PAUSE, FF

Using the Numeric buttons

CHANNEL 1–9 Press each button between 1 to 9.

CHANNEL 10 Press the [+10] button first, then press the 0 button again within 3 seconds.

CHANNEL 11–16 Press the [+10] button first, then press any number between 1 to 6 within 3 seconds.

Changing the Remote Control ID

Remote control’s ID and DVR’s ID should be matched for proper operation.

1. Press the [ID] button of the remote control and check the ID displayed on the DVR screen.

The factory default ID of the remote control is 00.

2. Enter 2 digits of your selection in order, while pressing the [ID] button of the remote control.

3. When ID input is done, press the [ID] button of the remote control again to check the setting.



If you want to change the remote control ID to 08: Press 0 and 8 in order while the [ID] button of the remote control is pressed.

For changing the ID of remote device, refer to “Remote Devices”. (Page 54)

● OVERVIEW

English _15

installation

DVD RECO

RDER

DVD RECO

RDER

Please take note of the followings before using this product.

• Do not use the product outdoor.

• Do not spill water or liquid in the connection part of the product.

• Do not impose the system to excessive shock or force.

• Do not pull out the power plug forcefully.

• Do not disassemble the product on your own.

• Do not exceed the rated input/output range.

• Use a certified power cord only.

• For the product with an input ground, use a grounded power plug.

CHECKING THE INSTALLATION ENVIRONMENT

This product is a top-notch security device that is equipped with a high-capacity HDD and other key circuit boards.

Temperature Unit: ºC

One Year: 24HR X 365 DAY =8,760 HR

When the temperature rises inside the product, the product may breakdown and the product life be shortened. Please pay attention to the following recommendations before installation.

Life (Unit: HOURS)

[Figure 1]

When mounting the product on a rack, comply with the following instructions.

1. Please ensure that the rack inside is not sealed.

2. Please ensure the air is circulated through the inlet/outlet as shown in the picture.

3. If you pile up the prudcts or other rack-mount devices as shown in figure 2, secure

room for ventilation or install a vent.

DVD RE

CO RDE

For natural air convection, place the inlet at the bottom of the rack and the outlet on top.

5. It is strongly recommended that a fan motor is installed at the inlet and the outlet for

air circulation. (Please fit a filter at the inlet to screen dust or foreign substances.)

6. Please maintain the temperature inside the rack or surrounding areas between 0°C

~ 40°C (32°F ~ 104°F) as shown in the figure 1.

Rack Mount Instructions - The following or similar rack-mount instructions are included with the installation instructions :

A) Elevated Operating Ambient - If installed in a closed or multi-unit rack assembly, the

operating ambient temperature of the rack environment may be greater than room

D V D R

ECO R DE

DVD R

ECO RDE

D V D R

E CO RDER

D V D RECO

RDE

D V D RE

C O R DE

DVD R

EC O R DE

USB

U S B

USB

U SB

USB

US B

U S B

ambient. Therefore, consideration should be given to installing the equipment in an environment compatible with the maximum ambient temperature (Tma) specified by the manufacturer.

B) Reduced Air Flow - Installation of the equipment in a rack should be such that

the amount of air flow required for safe operation of the equipment is not compromised.

C) Mechanical Loading - Mounting of the equipment in the rack should be such

that a hazardous condition is not achieved due to uneven mechanical loading.

D) Circuit Overloading - Consideration should be given to the connection of the

equipment to the supply circuit and the effect that overloading of the circuits might have on overcurrent protection and supply wiring. Appropriate

[Figure 2]

consideration of equipment nameplate ratings should be used when addressing this concern.

E) Reliable Earthing - Reliable earthing of rack-mounted equipment should be maintained. Particular attention should

be given to supply connections other than direct connections to the branch circuit (e.g. use of power strips).

16_ installation

RACK INSTALLATION

Install the Bracket-Rack as shown in the figure, and then fasten the screws on both sides (2 screws on each side).

 Remove the screws on the left and right side of the DVR before installation.

 Fix the screws not to be loosened by vibrations.

Cautions when Installing in the Rack

To install multiple DVRs in the rack, make sure to separate the FOOT at the bottom of each DVR.

1. There are four FOOTs at the bottom of a DVR. Press the projected parts at both-ends of each “FOOT” and turn it counterclockwise.

2. “FOOT” is separated from the main body when it is turned to the end of fastening groove.

● INSTALLATION

INSTALLING THE HDD

Make sure to unplug the power cord from the wall outlet to prevent possible electric shock, injury or product damage. Please consult your provider for further information on HDD installation since improper installation or settings may damage the product.

 Make sure to unplug the power cord from the wall outlet before proceeding with the installation.

 Cautions for data loss (HDD care)

Please pay attention so that the data inside the HDD is not damaged. Before adding a HDD, please check the compatibility with this product. HDD is vulnerable to malfunction due to its sensitive nature especially against shock when operating. Please ensure that the HDD is free from such shock. We are not liable for any damage to the HDD incurred by user’s carelessness or miss use.

 Cases might cause damage to HDD or recorded data

To minimize the risk of data loss from a damaged HDD, please backup data as often as possible. If exposed to shock when disassembling or installing, data stored in the hard disk may be damaged. A sudden power failure or turning off the product while in HDD operation may damage the hard disk drive. HDD or files stored inside may be damaged if the main body is moved or impacted during the HDD operation.

English _17

installation

Cautions on HDD installation

1. When adding a new HDD, make sure to fasten screws tightly and use appropriate parts if required to fix

the HDD. Otherwise, the product may be damaged or does not operate properly.

2. Please check the HDD compatibility before adding a HDD.

 Please contact your nearest dealer to obtain the list of compatible devices.

Installing the HDD

 If the installed HDD had been used with other devices, it will be automatically formatted.

• Installing HDD by opening the cover

1. Pull the front cover to open.

2. Open the front cover and check the HDD mounting

bracket.

 To prevent from USB ports being damaged, please unplug USB

devices before openning the front cover.

3. Separate the HDD bracket by pushing the lock on the left.

 Be careful not to scratch the hand while separating the HDD

bracket.

18_ installation

4. Insert the HDD into the bracket groove. Insert one side first

and gently lift up the other side.

5. Align the bracket with installed HDD to the guide of the case, push it toward the board.

 Push it firmly until you hear the clicking sound.

IF it is not fully mounted, HDD detection may fail.

6. You can check the HDD map directly on the DVR. Refer to “Storage Device > HDD Map”. (Page 51)

● INSTALLATION

7. Press it upward so that the front cover is closed.

• Replacing the mounted HDD

1. Open the bracket in the direction of arrow to separate the holder from the HDD.

2. Open other parts of the bracket wide to separate it from the holder.

 Remaining instructions after replacing the HDD is same as in

“Installing the HDD”.









English _19

connecting with other device

USB

CONNECTING EXTERNAL DEVICES

 The following figures are based on Model SRD-1656D.

AC 100-240V~IN

SPOT1, 2

HDMI

AUDIO OUT

AUDIO IN

Connecting the USB

VIDEO IN

AUDIO IN

VIDEO OUT (VGA)

eSATA HDD

1. By factory default, a USB port is provided for external connection.

2. You can connect a USB HDD, USB CD/DVD player, USB memory or mouse to the USB port.

If a USB HDD is connected to the system, recognition and settings are available in “Main Menu >

Storage Device”. (Page 51)

4. The product supports hot plugging function that enables connecting/disconnecting USB devices while in

operating the system.

 If the USB storage media for backup is not formatted by the product, format it as FAT32 file system with a PC.

Device

 To prevent from USB ports being damaged, please unplug USB devices before openning the front cover.

20_ connecting with other device

Connecting External SATA HDD (eSATA)

USB

ALARM IN

NO CONNECTION

AUDIO IN CH

5 ~ CH8

USB

ALARM IN

NO CONNECTION

AUDIO IN CH5 ~ CH

External SATA port is provided on the rear panel. If connected to the system, the external SATA HDD (eSATA) can be recognized and configured in “Main Menu > Device > Storage Device”.

 Use a cable shorter than 1 m for the external external SATA HDD (eSATA) connections.

 Unexpected disconnection to a device in use which is connected via eSATA may restart the system. Check whether the

device is in use before disconnecting it.

Connecting POS Device

You can connect a POS device to the RS-232C port on the product’s rear side when you connect it directly with a RS-232C cable. Connection setup for the RS-232C port is available in “Main Menu > Device > POS Devices”, press the <POS Device Setup> button and set <Baudrate, Parity, Data, Stop bit>. (Page 55)

Connecting the Alarm Input/Output

The Alarm In/Out port at the back is composed of the following.

SRD-

876D

● CONNECTING WITH OTHER DEVICE

Sensors

Alarm

• ALARM IN 1 ~ 8 : Alarm Input Port

• ALARM RESET : On receiving an Alarm Reset signal, the system cancels the current Alarm Input and

resumes sensing.

• ALARM OUT 1 ~ 4 : Alarm Output Port

125VAC 0.5A MAX)

ALARM OUT

(30VDC 2A,

ALARM IN (5mA sink)

English _21

connecting with other device

USB

SRD-1656D/1676D

Sensors

Alarm

• ALARM IN 1 ~ 16 : Alarm Input Port

• ALARM RESET : On receiving an Alarm Reset signal, the system cancels the current Alarm Input and

resumes sensing.

• ALARM OUT 1 ~ 4 : Alarm Output Port

ALARM OUT

(30VDC 2A,

125VAC 0.5A MAX)

ALARM IN (5mA sink)

22_ connecting with other device

Connecting the RS-485 Device

USB

Connect the [TX/RX +, –] device through the back port.

PTZ camera

 You can connect and control the PTZ camera which supports the RS-485 communication.

 Check if the RS-485 device is compatible with the product first.

 Pay attention not to change the polarity (+/-) of the RS-485 device when connecting it.

 Depending on camera’s type, connection polarity can be different.

For further information, refer to the respective PTZ Camera’s documentation.

● CONNECTING WITH OTHER DEVICE

system keyboard

CONNECTING THE NETWORK

Connecting to Network through Ethernet (10/100/1000BaseT)

RJ-45 Ethernet Cable (Direct Cable)

NETWORK

Hub/Switcher

Back Bone

Windows

Network Viewer

Hub/Switcher

English _23

connecting with other device

USB

Connecting to the Network using the router

Broadband Router

xDSL or Cable Modem

NETWORK

Connecting to Network through PPPoE

NETWORK

Phone(PPPoE) Line

xDSL or Cable Modem

RJ-45 Ethernet Cable (Direct Cable)

Network Viewer

External Remote PC

DDNS Server (Data Center)

PPPoE MODEM

Windows

24_ connecting with other device

Hub/Switcher

live

GETTING STARTED

Starting the system

1. Connect power cable to the product’s rear.

2. Touch and hold the front power button for over 3 seconds.

 It takes about 10 seconds to display the start screen after

booting.

3. The boot up screen appears. Booting up may take about 3 minute, as indicates progress with icons. If a new HDD is installed, the initialization process may take longer.

4. The live screen appears with a beep.

● LIVE

REC

2014-01-01 01:10:25

English _25

live

Shutting Down the System

You can shut down the system only if you have logged in to the DVR. You require permission to shut down the system if you are not logged in as admin.

1. Hold the [POWER] button on the front or the remote

control for over 3 seconds, or right click and click <Shutdown>.

2. The “Shutdown” confirmation window appears.

3. Use the arrow keys on the remote control or the front

panel to move to <OK> and press the [ENTER] button or click <OK>. The system will shut down.

 For the permission management, refer to “Permission

Management > Setting Permissions”. (Page 43)

To access a DVR or restricted menu, you should have logged in to the DVR.

1. In live mode, right-click any area of the screen.

You will see the context sensitive menu as in the right figure.

2014-01-01 01:10:25

Shutdown

Are you sure to shutdown?

OK Cancel

2014-01-01 01:10:25

Scene Mode Spot Out 1 Spot Out 2 Audio Off Freeze Stop Alarm Record Play Search Backup Main Menu Shutdown Hide Launcher Login



2. Click <Login>.

The login dialog appears. You can also see the login dialog to access a desired menu by pressing the [MENU] button on the remote control or the front panel.

26_ live

2014-01-01 01:10:25

ID admin



Password

 The login dialog will also appear if you press a menu button on the

remote control or the front panel of the DVR when the corresponding



OK Cancel

menu requires logging in.

 After logged in, press [RETURN] on the remote control to display the

logout dialog.

 For the restricted permission, refer to “Permission Management > Setting Permissions”. (Page 43)

 The default administrator ID is “admin”, and the password must be set when the user log in at the first time.

 Set password for your wireless network if you use the product with a wireless router. Being not protected with password or

using the default wireless router password may expose your video data to potential threat.

 To prevent from your personal information being exposed, please change your password every 3 months.

 Note that the security and other related issues caused by careless management of password shall be be in the charge of the

user.

Locking All Buttons

This will restrict access to all buttons available in the DVR.

1. In Live mode, press buttons in the order of [STOP (@)] [FREEZE][STOP (@)][FREEZE][MENU]. <All Key Lock> confirmation window appears.

2. Select <OK>. All keys are locked.

3. In the lock condition, press any button to display a dialog where you are prompted to enter the password for unlocking the buttons. The button lock will be released if you enter the admin password.

2014-01-01 01:10:25

All Key Lock

Are you sure to all key lock?

OK Cancel

● LIVE

English _27

live

CAM 01

LIVE SCREEN CONFIGURATION

Icons on the Live Screen

You can check the status or operation of the DVR with the icons on the live screen.

 b



CAM 01

Part Names Functions

Current Date, Time Displays the current time and date.

Displayed if the recording is in process.

 To cancel the recording, enter the password.

Displayed if the zoom function is activated.

Screen Mode

Displayed if you press the Pause button.

 b c

2014-01-01 01:10:25







28_ live



System

Operation

Displayed in Auto Sequence mode where all channels are switched at the specific time interval.

Displayed if there is a problem with the cooling fan.

Displayed if the HDD is full and the DVR has an insufficient space to record.

Displayed if no HDD is installed or the existing HDD should be replaced.

Displayed if the HDD needs a technical examination.

Displayed while the backup is in process or if the backup data is played.

Displayed if a new firmware is found from the network.

Part Names Functions





Video Input

Status

Camera Name/ Channel Displays the camera name and the changed channel, if any.

Displayed if no input is entered in the condition that the camera is set to <ON>.

Nothing will be displayed on the screen if the camera is set to <OFF>.

Displayed in PTZ setting, and highlighted yellow if PTZ is in operation.

Displays AUDIO ON/MUTE. Not displayed in video mode if deactivated.

If the sensor is set to <ON>, the input signal will be displayed on the screen of the



Camera

Operation

connected channel.

Displayed if a motion detected in the condition that the motion detection is set to <ON>.

Appears when the Tampering Detection is set to <ON> and a tampering attempt is detected.

Displays the current record mode from Record/Event/Schedule.

Error Information

• If the internal HDD is not connected, the “NO HDD”( ) message will appear; if there occurs a problem,

you will see the “HDD FAIL”( service center for assistance as this may cause a failure of recording, playback or backup.

• If the cooling fan does not work properly or has a problem, the <Fan Information> window will appear and

the fan error icon (

) will be displayed on the top left corner. In this case, check to see if the internal fan works. As a fan error can shorten the product life, make sure you contact the service center for assistance.

) message in the top left corner. In this case, make sure you contact the

● LIVE

 If you see the fan error icon or No HDD, HDD FAIL icons on the screen, contact the service center for more details.

Live Screen Menu

In addition to the buttons on the front panel or the remote control, you can access a desired menu by rightclicking the mouse any area in live mode. Right click opens the context menu which shows different menu items according to the situation, such as logged in/out state, split screen mode, and various operational conditions.

 Menu items of Search, Record, Backup, Shutdown and PTZ can be deactivated, depending on the user permission.

Scene Mode

2014-01-01 01:10:25

Spot Out 1 Spot Out 2 Audio Off Freeze Stop Alarm Record Play Search Backup Main Menu Shutdown Hide Launcher Logout

< Split Mode Menu >



2014-01-01 01:10:25

Scene Mode Spot Out 1 Spot Out 2 PTZ Control Zoom In Audio Freeze Stop Alarm Record Play Search Backup Main Menu Shutdown Hide Launcher Logout

< Single Mode Menu >



English _29

live

Split Mode Menu

The context sensitive menu in split mode differs, depending on the login/logout status.





















Menu Functions

Scene Mode Refer to “Live Mode”. (Page 33)



Spot Out1/2 Refer to “Spot Out”. (Page 35)

Audio On/Off Refer to “Audio ON/OFF”. (Page 36)

Freeze Refer to “Freeze”. (Page 36)



Stop Alarm Stops the alarm output and the event monitoring. Refer to “Event Monitoring”. (Page 37)



Record/Stop Starts/stops the standard recording.



Play Plays the search result (data). Refer to “Search & Play > Play”. (Page 85)



Scene Mode Spot Out 1 Spot Out 2 Audio Off Freeze Stop Alarm Record Play Search Backup Main Menu Shutdown Hide Launcher Logout

2014-01-01 01:10:25



30_ live

Search Refer to “Search & Play > Search”. (Page 82)



Backup Refer to “Main Menu > Setting the Backup”. (Page 64)



Main Menu Accesses the main menu. Refer to the Using the DVR section. (Page 38)



Shutdown Turns down the DVR.



Show/Hide Launcher Shows or hides the launcher. Refer to “Show / Hide the Launcher Menu”. (Page 32)



+ 120 hidden pages