Samsung SPD-2200 User Manual

Operation/Programming

P/No.:6806-0575-01A

■ Before attempting to operate this product, please read
the instructions carefully.

SAMSUNG TECHWIN CO., LTD.

145-3, Sangdaewon 1-dong, Jungwon-gu,
Seongnam-si, Gyeonggi-do 462-703, Korea
Tel : [phone]~8141 Fax : [phone]

SAMSUNG OPTO-ELECTRONICS AMERICA, INC.
ELECTORONIC IMAGING DIV.

40 Seaview Drive, Secaucus, NJ 07094, U.S.A
Tel : [phone] Fax : [phone]

SAMSUNG TECHWIN MOSCOW OFFICE

Korp 14, 37-A, PR-KT, Lenningradsky,
Moscow 125167, Russia
Tel : [phone], 9298 Fax : [phone]

SAMSUNG OPTO-ELECTRONICS UK LTD.

Samsung House, 1000 Hillswood Drive,
Hillswood Business Park Chertsey, Surrey KT16 OPS
Tel : [phone] Fax : [phone]

TIANJIN SAMSUNG OPTO-ELECTRONICS CO., LTD .

7 Pingchang Rd., Nankai Dist. Tianjin 300190, P.R China
Tel : [phone](33821) Fax : [phone]

SALES NETWORK

http://www.samsungtechwin.com
http://www.samsungcctv.com

•

ENGLISH

•

ESPAÑOL

•日本語

Thank you for purchasing a SAMSUNG CCTV CAMERA.

Before operating the camera, confirm the camera model and proper
input power voltage. In order that you can understand this manual
thoroughly, we'll introduce our model description.

Model Description

SPD-2200 x

• Signal System
N NTSC Model
P PAL Model

3

SPEED DOME CAMERA

2

SPEED DOME CAMERA

This installation should be made by a qualified service person

and should conform to all local codes.

The lightning flash with an arrowhead symbol, within an equilateral
triangle is intended to alert the user to the presence of uninsulated
“dangerous voltage” within the product's enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the
user to the presence of important operating and maintenance (servicing)
instructions in the literature accompanying the appliance.

INFORMATION -This equipment has been tested and found to comply with
limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instruction manual, may
cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the
interference at his own expense.

WARNING - Changes or modifications not expressly approved by the
manufacturer could void the user’s authority to operate the equipment.

CAUTION : To prevent electric shock and risk of fire hazards:

Do NOT use power sources other than that specified.
Do NOT expose this appliance to rain or moisture.

Signal System

ENGLISH

Warning & Caution .................................................................................... 6

Main Features ........................................................................................... 9

Components ............................................................................................ 10

Front Panel ................................................................................... 10

Back Panel .....................................................................................11

Getting started ......................................................................................... 12

Bracket Setup for Installation .........................................................12

Initial Setting ..................................................................................13

Accessories ....................................................................................19

How to Install ........................................................................................... 20

Cable ..............................................................................................20

Accessories (option) .......................................................................22

How to Install Camera ....................................................................24

5

SPEED DOME CAMERA

4

SPEED DOME CAMERA

Camera settings ...................................................................................... 26

OSD Menu Configuration .............................................................. 26

Dome Camera User’s Menu Setting ............................................ 28

Camera Setting ............................................................................. 28

Sequence Setting ......................................................................... 35

P/T Setting .................................................................................... 40

OSD Setting ................................................................................. 44

Alarm Setting ............................................................................... 47

Initialize Setting ............................................................................. 50

Status ............................................................................................ 51

Product Appearance and Installation Method ......................................... 52

System configuration................................................................................ 53

Specifications .......................................................................................... 55

Contents

ENGLISH

7

SPEED DOME CAMERA

6

SPEED DOME CAMERA

Warning & Caution

Please read the instructions carefully for correct use of the product, and observe these
cautions to prevent danger or physical damage while operating it.

If you fail to read this information, or handle the product
incorrectly, death or serious injury may result.

Warning / Caution

Sign

If you fail to read this information, or handle the product
incorrectly, serious injury or physical damage may result.

Not allowed.

No disassembly.

Be sure to keep this.

Warning

Caution

Never install the product in areas exposed to

water, oil or gas.

Doing so may result in malfunctions, electric shock or fire.

The unit should be installed by trained

personnel.

Installation by unskilled personnel without sufficient experience or
expertise may result in fire or electric shock. Always ask your sales
agent to perform installation.

Always stop using the product if it emits smoke

or becomes unusually hot.

Continuing to use it under such circumstances may result in fire.

Never install the product on a ceiling that Is not

strong enough to bear its weight.

The product may fall.

Never disassemble the product or insert foreign

bodies into it.

Malfunction may result.

Never touch the power cord with wet hands.

Touching the power cord with wet hands may result in electric shock.

Warning

ENGLISH

9

SPEED DOME CAMERA

8

SPEED DOME CAMERA

Never expose the product to direct sunlight or

harmful rays.

Direct sunlight or harmful rays may cause fatal damage to the CCD
or internal circuitry.

Never drop the product, or subject it to severe

impact or vibration.

Malfunction may result.

Never install the product in areas exposed to

rain or water.

If water gets into the product it may cause failure.

Never install the product in locations with

extreme high or low temperature.

Installing the product in areas subject to temperatures of over 50°C
or below 0°C may result in deterioration of picture quality or other
problems. Pay special attention to ventilation when installing the
product in high ambient temperatures.

Never install the product in places where the

lighting conditions fluctuate.

Frequent changes of illumination, for example from unstable
fluorescent lighting, may result in malfunction.

Never touch the glass on the front of the

product.

This glass is one of the key components.
Be careful not to leave fingerprints or other marks on the glass.

Caution Main Features

Auto-focusing 22x Zoom lens

The digital zoom function of the built-in 22x zoom
lens, together with its auto-focus feature, zooms
an image by up to 220x.

Day & Night function

Slow-shutter and day and night switching enable
optimum screen monitoring over 24 hours.

✽Slow-shutter function improves CCD sensitivity

by electrically lengthening exposure time.

✽Day & Night function enables the color and

black and white screens to be used respectively
during the day and at night.

Various auto-surveillance functions

·PTZ trace
Manually plays recorded images of up to about
120 seconds.

·Auto swing
Repeats pan and tilt between two preset
positions.

·Group sequence
Switches to and checks a maximum of 128
preset positions in order.

·Tour sequence
Switches to and checks a maximum of 6 group
sequences in order.

OSD (On Screen Display) function

Provides character information displayed on the
monitor, such as the camera ID address, camera
name, preset number, preset name, area name
and sequence status, and easily sets various
camera functions from the OSD menu screen.

Smart P/T function

Pan and tilt speed compensation function linked
to zoom position allows fine manual operation
even during zooming.

Area Masking for 8 points

Area Masking can be set up for up to 8 points.
For Privacy, this device provides a function for
hiding the points for which Area Masking is
selected from the screen.

Home Position Auto Return function

Returns the dome to a specified preset position
at a fixed time after ending manual operation.

128 Preset Positions

A maximum of 128 preset positions can be set.
The preset function enables you to set the
location you want to monitor at any time.

Auto Flip

For monitoring an object moving below a
camera, run Auto Flip using a joystick controller,
and moving objects can be monitored without
reversing, both up and down and left to right.

ENGLISH

11

SPEED DOME CAMERA

10

SPEED DOME CAMERA

Rotary Switch 2 (SW2)

Camera ID address setting
switch.

Rotary Switch 1 (SW1)

Camera ID address setting
switch.

Connector Cable

Connect to the bracket
connector for installation.

Power Switch

Power on or off

(※Factory default : OFF)

DIP Switch (SW3)

For setting each function

1. For selecting a controller

2. For factory setting

3. For terminal setting

4. For terminal setting

Components

Front Panel Back Panel

·If the Rotary Switch and DIP Switch (SW3) are not displayed, turn the power off and on again. Both switches will then be
displayed.

·Do not pull or hold onto the connector cables when moving or delivering the product. It may cause operational failure.

·See the inside of the door for settings for the switches on the main unit of the product.

Cautions

Protocol Selection Switch

Power In Terminal

Controller In Terminal

Video Out Terminal

AC 24V Out

ALARM Out

ALARM In

Power LED

ENGLISH

13

SPEED DOME CAMERA

12

SPEED DOME CAMERA

Bracket Setup for Installation Initial Setting

●

Communication Protocol Setting (Installation Bracket)

Select and set SW1 on the installation bracket for setting the communication protocol.

●

Camera ID Setting (Mainframe front panel)

·

Set the Camera ID using the two rotary switches. SW1 and SW2
refer to the lower and upper positions, respectively.

SW1

0
1
2
3
4

5~F

Samsung
Samsung

Pelco-D
Pelco-D
Pelco-D
Reserve

9,600

19,200

2,400
4,800
9,600

Protocol

Baud Rate (BPS)

●

Baud Rate Setting by DVR Model

For control of the speed dome camera using DVR without a dedicated controller, set the baud rate by DVR
model as described below.

DVR Model

Protocol

SVR-430

SVR-900/1620

SVR-1630

9600,19200
9600,19200
9600,19200

9,600

4800, 9600

2400,4800,9600

Samsung

Pelco

·

EX) If the camera ID is number 1, set as described below.

SW2 SW1

01

Getting started

Note) Factory Default : 0 (Samsung, 9600)

Note) A faster rate may degrade stability.

The control function may not be available depending on the DVR Firmware version.
Be sure to install the latest DVR Firmware version.

SW2 SW1

Video Out

Alarm In 1
Alarm In 2

Alarm In 3
Alarm In 4

Alarm Out 1

Alarm Out 2

AC 24V Output (for Heater connection)

Mainframe 18PIN Connector

ENGLISH

15

SPEED DOME CAMERA

14

SPEED DOME CAMERA

●

Camera ID Switch Setting

Camera ID SW2 SW1 Remarks
ID = 0 0 0

Not applicable

ID = 1 0 1
ID = 2 0 2
ID = 3 0 3
ID = 4 0 4
ID = 5 0 5
ID = 6 0 6
ID = 7 0 7
ID = 8 0 8
ID = 9 0 9
ID = 10 0 A
ID = 11 0 B
ID = 12 0 C
ID = 13 0 D
ID = 14 0 E
ID = 15 0 F
ID = 16 1 0
ID = 17 1 1
ID = 18 1 2
ID = 19 1 3
ID = 20 1 4
ID = 21 1 5
ID = 22 1 6
ID = 23 1 7
ID = 24 1 8
ID = 25 1 9
ID = 26 1 A
ID = 27 1 B
ID = 28 1 C
ID = 29 1 D
ID = 30 1 E
ID = 31 1 F
ID = 32 2 0
ID = 33 2 1
ID = 34 2 2
ID = 35 2 3
ID = 36 2 4
ID = 37 2 5
ID = 38 2 6
ID = 39 2 7
ID = 40 2 8
ID = 41 2 9
ID = 42 2 A
ID = 43 2 B
ID = 44 2 C
ID = 45 2 D
ID = 46 2 E
ID = 47 2 F

Camera ID SW2 SW1 Remarks
ID = 48 3 0

ID = 49 3 1
ID = 50 3 2
ID = 51 3 3
ID = 52 3 4
ID = 53 3 5
ID = 54 3 6
ID = 55 3 7
ID = 56 3 8
ID = 57 3 9
ID = 58 3 A
ID = 59 3 B
ID = 60 3 C
ID = 61 3 D
ID = 62 3 E
ID = 63 3 F
ID = 64 4 0
ID = 65 4 1
ID = 66 4 2
ID = 67 4 3
ID = 68 4 4
ID = 69 4 5
ID = 70 4 6
ID = 71 4 7
ID = 72 4 8
ID = 73 4 9
ID = 74 4 A
ID = 75 4 B
ID = 76 4 C
ID = 77 4 D
ID = 78 4 E
ID = 79 4 F
ID = 80 5 0
ID = 81 5 1
ID = 82 5 2
ID = 83 5 3
ID = 84 5 4
ID = 85 5 5
ID = 86 5 6
ID = 87 5 7
ID = 88 5 8
ID = 89 5 9
ID = 90 5 A
ID = 91 5 B
ID = 92 5 C
ID = 93 5 D
ID = 94 5 E
ID = 95 5 F

Camera ID SW2 SW1 Remarks
ID = 96 6 0

ID = 97 6 1
ID = 98 6 2
ID = 99 6 3
ID = 100 6 4
ID = 101 6 5
ID = 102 6 6
ID = 103 6 7
ID = 104 6 8
ID = 105 6 9
ID = 106 6 A
ID = 107 6 B
ID = 108 6 C
ID = 109 6 D
ID = 110 6 E
ID = 111 6 F
ID = 112 7 0
ID = 113 7 1
ID = 114 7 2
ID = 115 7 3
ID = 116 7 4
ID = 117 7 5
ID = 118 7 6
ID = 119 7 7
ID = 120 7 8
ID = 121 7 9
ID = 122 7 A
ID = 123 7 B
ID = 124 7 C
ID = 125 7 D
ID = 126 7 E
ID = 127 7 F
ID = 128 8 0
ID = 129 8 1
ID = 130 8 2
ID = 131 8 3
ID = 132 8 4
ID = 133 8 5
ID = 134 8 6
ID = 135 8 7
ID = 136 8 8
ID = 137 8 9
ID = 138 8 A
ID = 139 8 B
ID = 140 8 C
ID = 141 8 D
ID = 142 8 E
ID = 143 8 F

Camera ID SW2 SW1 Remarks
ID = 144 9 0

ID = 145 9 1
ID = 146 9 2
ID = 147 9 3
ID = 148 9 4
ID = 149 9 5
ID = 150 9 6
ID = 151 9 7
ID = 152 9 8
ID = 153 9 9
ID = 154 9 A
ID = 155 9 B
ID = 156 9 C
ID = 157 9 D
ID = 158 9 E
ID = 159 9 F
ID = 160 A 0

Not applicable

ID = 161 A 1
ID = 162 A 2
ID = 163 A 3
ID = 164 A 4
ID = 165 A 5
ID = 166 A 6
ID = 167 A 7
ID = 168 A 8
ID = 169 A 9
ID = 170 A A
ID = 171 A B
ID = 172 A C
ID = 173 A D
ID = 174 A E
ID = 175 A F

Not applicable

ID = 176 B 0
ID = 177 B 1
ID = 178 B 2
ID = 179 B 3
ID = 180 B 4
ID = 181 B 5
ID = 182 B 6
ID = 183 B 7
ID = 184 B 8
ID = 185 B 9
ID = 186 B A
ID = 187 B B
ID = 188 B C
ID = 189 B D
ID = 190 B E
ID = 191 B F

Getting started

ENGLISH

17

SPEED DOME CAMERA

16

SPEED DOME CAMERA

Camera ID SW2 SW1 Remarks
ID = 192 C 0

ID = 193 C 1
ID = 194 C 2
ID = 195 C 3
ID = 196 C 4
ID = 197 C 5
ID = 198 C 6
ID = 199 C 7
ID = 200 C 8
ID = 201 C 9
ID = 202 C A
ID = 203 C B
ID = 204 C C
ID = 205 C D
ID = 206 C E
ID = 207 C F
ID = 208 D 0
ID = 209 D 1
ID = 210 D 2
ID = 211 D 3
ID = 212 D 4
ID = 213 D 5
ID = 214 D 6
ID = 215 D 7
ID = 216 D 8
ID = 217 D 9
ID = 218 D A
ID = 219 D B
ID = 220 D C
ID = 221 D D
ID = 222 D E
ID = 223 D F
ID = 224 E 0
ID = 225 E 1
ID = 226 E 2
ID = 227 E 3
ID = 228 E 4
ID = 229 E 5
ID = 230 E 6
ID = 231 E 7
ID = 232 E 8
ID = 233 E 9
ID = 234 E A
ID = 235 E B
ID = 236 E C
ID = 237 E D
ID = 238 E E
ID = 239 E F

Camera ID SW2 SW1 Remarks
ID = 240 F 0

ID = 241 F 1
ID = 242 F 2
ID = 243 F 3
ID = 244 F 4
ID = 245 F 5
ID = 246 F 6
ID = 247 F 7
ID = 248 F 8
ID = 249 F 9
ID = 250 F A
ID = 251 F B
ID = 252 F C
ID = 253 F D
ID = 254 F E
ID = 255 F F

·Factory Default : Camera ID = 1
The rotary switch is on the controller board (controllable from the initial PAN position)

Note

·The three kinds of camera ID below cannot be used.

Camera ID

ID = 0
ID = 160
ID = 175

0
A
A

0
0
F

R-SW2 R-SW1

●

Controller Model Setting (Mainframe front panel)

·Set the controller model by switching Dip Switch No. 1

●

Factory Default (Mainframe front panel)

SW3

ON

OFF

Functions

Controller Setting

SVR-430/900 /1620/1630

SCC-16, SCC-3000

SW3-#1

ON

OFF

Note) Factory Default : OFF

Note) Factory Default : OFF

Simultaneous control by a controller and a DVR is not allowed.

Note) Factory Default: On for both switches

Camera Connection Position

Longest Route Terminal

On the route

ON

OFF

ON

OFF

SW3-#3 SW3-#4

Functions

Factory Default

OFF for both switches

SW3-#2

ON

OFF

Getting started

●

RS-485 Terminal Setting (Mainframe front panel)

·Set the terminal by switching Dip Switch No. 3 and 4 On/Off.

ENGLISH

19

SPEED DOME CAMERA

18

SPEED DOME CAMERA

It is necessary to connect the terminating resistance to the two units that are furthermost from the relevant
camera/controller on the RS-485 Interface in order to prevent signal attenuation.

Since cameras have embedded terminating resistance, select whether to activate or deactivate their terminating
resistance by using the DIP Switch. Refer to the connection layout below for deciding which unit is to be connected to
the terminating resistance. Set the terminating resistance to the gray colored unit.

The maximum distance for setting the terminating
resistance is 1.2Km.

User’s manual

Accessories

Template

Installation Bracket

3 fixing screws

1cable lock screw

Safety wire

Component Model

Description

※

Options

The components below are options

Camera Controller

Wall mounted
Ceiling mounted
AC Adapter

Indoor Housing
Indoor Embedded Housing
Outdoor Housing

SCC-16, SCC-3000

STH-160PI

STB-270PW

STB-496PP

STA-110
STA-230

STH-128PE

STH-160PO

Housing for Indoor Installation
Ceiling Embedded Indoor Housing
Housing (with built-in fan and heater) for outdoor installation

Wall mounted type
Ceiling mounted type

Input : AC 110V
Input : AC 230V

Pan/Tilt/Zoom/Focus Control, OSD Action, a variety of function settings

Getting started

ENGLISH

21

SPEED DOME CAMERA

20

SPEED DOME CAMERA

Cable

Preparation

For SPD-2200 installation, the cables listed below have to be prepared.

●

Power adapter cable

The cable to be connected to the power in the SPD-2200 terminal includes the power adapter, for which the rated
voltage is AC24V, 2.5A as described below. (Use UL listed class 2 power source.)

Connection

1. First, connect one end of the BNC cable to the video
out terminal.

2. Connect the other end of the BNC cable to the video
in terminal of the monitor.

3. Connect one end of the power adapter, comprising
two lines, to the Power In Terminal of the bracket
using the flathead screwdriver as shown in the figure
below.

4. Connect the power adapter plug to the power outlet.

5. Connect the connection terminal of the SPD-2200
controller to the external controller.

● VideoCable

The cable connecting the SPD-2200 video out terminal and the monitor is the BNC cable as described below.

●

RS-485 Communication Cable

The cable connecting the controller for the SPD-2200’s RS-485 communication is described below.

Video Out Terminal

Monitor In Terminal

Monitor

Power In Terminal

Screwdriver

Power Adapter

Controller Connection
Terminal

Controller

Data Box

How to Install

·Adapter, Video and RS-485 communication cables not supplied.

Note

ENGLISH

4) Wall Mounting (STB-270PW)
Assembly used when an indoor and outdoor housing for a speed dome camera is to be mounted on a wall.

5) Ceiling Mounting (STB-496PP)
Assembly used when an indoor and outdoor housing for a speed dome camera is to be mounted on a

concrete ceiling.

23

SPEED DOME CAMERA

22

SPEED DOME CAMERA

Accessories (option)

●

Cautions

- Confirm that the installation location is strong enough to bear more than 4 times the total weight of the
assembly and the speed dome camera (SPD-2200).

- Only install the camera where there is more than 500mm of space above the ceiling board.

- In installing the bracket, use the installation guide template, screws and cables supplied with the camera.

- There is a risk that the camera may be dropped during installation. Prevent any possibility of the camera falling
by using the security cable during installation. Unauthorized persons should be prevented from gaining access
to the installation site.

●

Options related to installation

The options below, when purchased, will facilitate the installation in a variety of different sites.

1) Indoor embedded Housing (STH-128PE)

This housing is used when a speed dome camera is embedded in a double ceiling.

2) Indoor and Outdoor Housing (STH-160PI, STH-160PO)

This housing is used when a speed dome camera is mounted on a wall or ceiling inside or outside.

How to Install

·When installing the speed dome camera in an indoor/outdoor housing, remove the dome cover (front glass) to obtain a clearer
image.

Cautions

ENGLISH

25

SPEED DOME CAMERA

24

SPEED DOME CAMERA

How to Install the Camera (using the Embedded Housing)

① Make a hole of 155mm in diameter in the ceiling to install the camera. Pull the cable down through it.

② Connect the video cable, controller cable and power adapter cable to the mounting bracket. (See Page 19)

③ Fix the mounting bracket to the Embedded housing using three screws.
④ Fasten the eye bolt on the housing and fix the housing to the ceiling, using the cable to prevent it from falling.
⑤ Fix the housing to the ceiling using three screws.
⑥ Connect the Installation bracket to the connector of the speed dome camera.
⑦ Insert the pin at the bottom of the camera into the bracket fixing hole and turn it anticlockwise to secure.
⑧ Fasten the lock screw.
⑨ Place the external cover over the housing and then rotate and fix it.

Hole for Fixing the Dome Camera

Controller connection cable

Power adapter connection cable

Video connection cable

Ceiling

Installation Pin

Screws to prevent the

camera from coming loose.

Installation Bracket

Installation bracket connector

Camera connector

External Cover (Decoration ring)

Embedded Housing

·Check the power adapter input power before connecting the power supply.

·Install the camera using the installation template and cable and fixing screws that are supplied separately for installations

without a housing.

·Note that the locking screws should be fastened. If one of the locking screws is not properly fastened, the camera may fall due

to vibration or impact once it is installed.

Cautions

How to Install

ENGLISH

27

SPEED DOME CAMERA

26

SPEED DOME CAMERA

OSD Menu Configuration

This model enables dome camera setting, using the OSD (On Screen Display) menu displayed on the video output,
by exclusive control.

The joystick in the OSD menu modes is controlled as described below.
This function is also enabled by sending the exclusive control code from a PC to a dome camera.

Menu

TILT Up

TILT Down

PAN Left

PAN Right

Up on the OSD

Down on the OSD

Left on the OSD

Right on the OSD

Functions

●

Menu Configuration

Camera setting

·Preset setting is available both from the controller and the OSD menu.

Note

Focus Mode Auto/Manual/One Shot AF

One Shot AF

Digital Zoom 4X

AUTO/AWC/MANUAL

Auto

/OUTDOOR/INDOOR

Manual : WB RED 000

WB BLUE 000

AUTO/AGC OFF/ALL/AGC/IRIS/SHUTTER

Auto

- Shutter SPD 1/60

- Iris Adjust 170

- AGC Adust ­D&N Mode Auto/Day/Night Auto
Slow Shutter

0(OFF), 1~9 (2Fields~128Fields)

OFF
Mode ON/OFF OFF
Area Center/Upper/Lower/Left/Right Center
Weight Low/High Low
Internal Internal
Line Lock Line Lock Phase 225

050
ON/OFF OFF
Sharpness 10
Mirror ON/OFF OFF
Nega/Posi Negative/Positive Positive

Camera
Setting

Focus

White Balance

AWB Mode

AE Mode

Exposure

Others

Back Light

Sync

Flickerless

Brightness

P1 P2 P3 P4

Defaults

Setting/Execute/Clear/Status
Setting/Execute/Clear
Setting/Execute/Clear
Auto/Manual

MANUAL
Group1~Group6 Setting/Execute/Clear
Setting/Execute/Clear
Replay/Memorize
ON/OFF OFF
Position/ON/OFF
Position/ON/OFF
Area 1~ Area 8 Name/Position/Clear/On/Off
Mask1~Mask8 Position ON/OFF
ON/OFF
Setting
ON/OFF
ON/OFF ON
ON/OFF ON
ON/OFF ON
Edit, ON/OFF
ON/OFF ON
Edit, ON/OFF
ON/OFF ON
ON/OFF OFF
ON/OFF OFF

NC/NO/OFF
1~4(Priority)
Preset/Group/Tour
1~4
MD
1~60(Sec)
1~60(Min)

1~60(Hour)
Out1 Off~Out2 Off
MD Execute
Detect Area Whole/Upper/Lower/Center Whole
Sensitivity 12
Preset No.
Cancel / Execute
Cancel / Execute
Cancel / Execute
OFF, 1~7 Days 7 Days

Set Preset
Pan Swing
Tilt Swing
Swing Focus Mode
Group SEQ
Tour SEQ
PTZ Trace
Power On Resume
Pan Limit
Tilt Limit
Area Setting

Smart P/T
Auto Filp
Camera ID
Camera Name
Preset Number
Preset Name
Sequence Status
Area Name
Alarm Enable

Alarm Input

Alarm1~Alarm4

Alarm Out

Out1 Time~Out2 Time

Out1 SET~Out2 SET

Motion
Detection

Power On Reset
Factory Default Set
Camera Default Set
Auto Refresh

Sequence
Setting

P/T Setting

OSD Setting

Inltialize

Status

Alarm
Setting

Area Masking

Home Position

ENGLISH

29

SPEED DOME CAMERA

28

SPEED DOME CAMERA

●

Dome Camera Users’Menu Settings

How to Use the OSD Menu

Check whether the camera is set to manual mode and press the OSD Menu Key, or 1 and the MENU Key at the
same time.
The screen will then display the contents as shown below.

Main Menu

1) Camera Setting

Select Camera Setting in the Main Menu Window, and the Camera Setting Menu appears.

Camera Setting Menu

FOCUS

The Focus menu sets the focus mode to either Auto or Manual Mode.

①

Focus Mode

·Auto : Automatically focuses by continuous monitoring in Auto Mode. Since the focus is automatically
adjusted when the Zoom key is controlled, Focus key input is not applied.

·Manual : The Manual mode enables the user to manually adjust the focus.

·One Shot AF : One Shot AF activates auto-focusing when the camera stops moving.

When the camera stops, it works as in Manual Mode.

②

Digital Zoom

Changes the digital Zoom factors.
※We recommend setting the digital zoom factor before presetting.

Main Menu

Camera Setting
Sequence Setting
P/T Setting
OSD Setting
Alarm Setting
Initialize
Status

Move the cursor downwards to the submenu to set. Press the
Enter key on the selected submenu. You can then change and
set the submenu. Press the ESC KEY, and the OSD menu
closes.
For more details, please see the Controller User Manual.

Camera setting

Digital Zoom

·The higher the digital zoom factor, the lower the image quality.

Auto-focus

·The Auto-Focus may not work properly under the conditions below.

- If the illumination in a monitoring zone is low

- If the Slow-Shutter is activated

- If the amplification degree is increased

- If the illumination in a monitoring zone is excessively high

- If both remote objects and close objects are included in a monitoring zone

- If there is no contrast (black and white), such as the sky or a wall, within the picture

- If there is a thin horizontal line within an image

Cautions

Camera Setting

Camera Setting

White Balance
Exposure
Back Light OFF
Sync
Brightness 050
Flickerless OFF
Others

Focus

Press the
Enter key

Focus

One Shot Af

Digital Zoom 4X

Focus Mode

ENGLISH

31

SPEED DOME CAMERA

30

SPEED DOME CAMERA

Exposure

Controls the camera exposure

①

AE Mode

·Auto: Automatically adjusts the video signal brightness according to the light intensity.

·AGC OFF : Sets AGC Gain as OFF.

·All: Manually sets the electronic Shutter, Iris and AGC.

·AGC: Manually sets AGC.

-AGC Adjust : The AGC (Automatic Gain Control) menu sets whether or not to control the gain
automatically when an object is viewed in poor lighting, such that the image
brightness is below a certain level. Select the AGC Adjust menu, and you can increase
or decrease the level value.

·IRIS: Manually sets the Iris.

-Iris Adjust : Sets the video signal brightness on the screen by adjusting the Iris level.

·Shutter: Manually sets the electronic Shutter rate.

-Shutter SPD : The Shutter SPD supports 8 shutter speed rates from 1/60 sec. to 1/10,000 sec.

White Balance

The White Balance menu activates the white balance function, which adjusts the correct white color for lighting with any color
temperature.

Select from Auto/AWC/Indoor/Outdoor/Maunual

①

AWB Mode

·Auto : Automatically adjusts the colors according to changes in the light source.

·AWC : Sets the lighting condition for an object and forcibly adjusts its color to white. Images can only

be captured under this preset condition

·Manual : Sets the color temperature with the appropriate ratio of RED to BLUE.

- WB Manual
Users can adjust the colors by adding or reducing the percentage of Red or Blue.

- WB Red
The Red Gain can be changed.

- WB Blue
The Blue Gain can be changed.

·Outdoor: Sets the color temperature to 5,600K.

·Indoor : Sets the color temperature to 3,200K.

Camera setting

High-Speed Shutter

12 3 4 5 678

(Sec) 1/60 1/125 1/250 1/500 1/1,000 1/2,000 1/4,000 1/10,000

[Table-1 Step-by-Step Setting]

Camera Setting

Focus
White Balance
Exposure
Back Light OFF
Sync
Brightness 050
Flickerless OFF
Others

White Balance

Camera Setting

Focus
White Balance
Exposure
Back Light OFF
Sync
Brightness 050
Flickerless OFF
Others

Exposure

White Balance

AUTO

AWB Mode

Press the
Enter key

Exposure

AE Mode AUTO
D & N Mode AUTO
Slow Shutter 6

AE Mode

Press the
Enter key

ENGLISH

Note

33

SPEED DOME CAMERA

32

SPEED DOME CAMERA

②

D&N Mode (Day & Night Mode)

Automatically detects the degree of darkness at night, or in poor lighting conditions, and so keeps the screen
bright and clear.

·Auto : When the Auto Mode is selected, it automatically switches to Color mode to maintain optimum color
during the day, and to Black and White mode at night for clearer pictures in poor lighting.

However, the Slow Shutter doesn’t work in Auto Mode.

·Day : Maintains color images. The Slow Shutter function is activated in this mode.

·Night : Maintains black and white images. The Slow Shutter function is deactivated in this mode.

③

Slow Shutter

The Slow Shutter is activated only in Day Mode and keeps the screen bright and clear in low lighting
conditions.

Increase the level in the menu, and the maximum level can be adjusted. (X2~X128) The larger the scale, the
brighter the screen. However, the after-image of moving objects is also increased.

Low-Speed Shutter 0 1 2 3 4 5 6 7 8 9

(Fields)

Shutter OFF

X2 X4 X8 X12 X16 X24 X32 X64 X128

[Table-2 Step-by-Step Setting]

Back Light Ctrl

·BLC Mode
Use when the difference between light levels at the center of the screen and the edge of the screen is great –
for example when there is backlight.
ON activates the Backlight function and OFF deactivates it. The default is OFF.

·Area Mode
Set the area for backlight compensation. The default is Center.

- Center : compensates for backlight in the center area of the screen.

- Upper : compensates for backlight in the upper area of the screen.

- Lower : compensates for backlight in the lower area of the screen.

- Left : compensates for backlight in the left area of the screen.

- Right : compensates for backlight in the right area of the screen.

·Weight
Set the level of backlight compensation. The default is High.

- Low : slightly improves the backlight compensation.

- High : substantially improves the backlight compensation.

Camera setting

AE

D&N

Shutter

Day(OFF)

Auto

Night(ON)

Adjustable
Auto Mode
Auto Mode

Adjustable
Keep the Day status value (No change allowed)
Keep the Day status value (No change allowed)

Adjustable
Keep the Day status value (No change allowed)
Keep the Day status value (No change allowed)

Iris AGC

AE

D&N

AUTO

Day(OFF)

Auto

Slow Shutter Mode available

Automatic D&N switching available

Slow Shutter Mode not available

Automatic D&N switching not available

Manual

The relationship between AE Mode and D&N Mode is described below.

The relationship between AE Mode and D&N Mode is described below.

Press the
Enter key

Camera Setting

Focus
White Balance
Exposure
Back Light
Sync
Brightness 050
Flickerless OFF
Others

Back Light

Back Light

Mode OFF
Area CENTER
Weight LOW

Mode

Center Upper Lower Left Right

·The Area and Weight set by BLC Mode are only effective only when a camera is not moving. When the camera is rotating, as with
Preset/Group/Tour/Trace, the camera works with the Area on Center and the Weight on High.

Note

ENGLISH

35

SPEED DOME CAMERA

34

SPEED DOME CAMERA

Camera setting

Others

①

Sharpness

Highlights image contour by increasing the Aperture Gain of the camera.

②

Mirror

Reverses the video output signal from left to right and vice versa

③

Nega/Posi

The video output signal is changed to positive or negative.

2) Sequence Setting

②

Pan Swing

Activates and sets Swing monitoring in the Pan direction and deletes data

·Setting : Selects the preset swing position with the joystick and sets the position with the Enter key.
SPD is the speed the camera moves.(001~240°/sec)
DWL is the dwell time for the camera.(1~128sec)
Completes the setting by pressing the Enter key on the selected position.

·Execute:Starts swing monitoring.
Stops it with the Stop key.

·Clear : Deletes the swing data

①

Set Preset

When users set their own chosen PAN/TILT positions or ZOOM and FOCUS, they can call frequently and monitor
the status. Up to 128 positions can be preset. (1~128)

·Setting : Select the preset No. to set, adjust the PAN/TILT/ZOOM and press Enter.

·Execute : Select the preset No. to run, and the relevant camera starts running.

·Clear : Select the preset No. to clear, and the relevant setting is deleted.

·Status : Displays the current preset No.

Sync

Selects Internal synchronization/Line Lock. The default is Internal synchronization.

·Internal : Internal sync method

·Line Lock : The internal sync method is the power-frequency synchronization method. The power phases of

several units can be adjusted.

·Line Lock Phase : With the Line Lock, the phase can be adjusted from 0°to 360°. The default is 225°.
※For Internal, the Line Lock Phase cannot be adjusted.

Brightness

Sets video signal brightness on the screen.

Flickerless

Flickerless Mode

Sets the Flickerless Mode ON or OFF. Fluorescent tube flicker is eliminated.

Sync

Internal

Line Lock Phase 225

Sync Mode

Press the
Enter key

Camera Setting

Focus
White Balance
Exposure
Back Light
Sync
Brightness 050
Flickerless OFF
Others

Sync

·D/N Mode is not activated when the Flickerless mode is ON.

Note

Sequence Setting

Set Preset
Pan Swing
Tilt Swing
Swing Focus Mode MANUAL
Group SEQ
Tour SEQ
PTZ Trace
Power On Resume OFF

Pan Swing

Pan Swing

Execute
Clear

Setting

Press the
Enter key

Sequence Setting

Pan Swing
Tilt Swing
Swing Focus Mode MANUAL
Group SEQ
Tour SEQ
PTZ Trace
Power On Resume OFF

Set Preset

Set Preset

Execute
Clear
Status

Setting

Press the
Enter key

ENGLISH

37

SPEED DOME CAMERA

36

SPEED DOME CAMERA

Camera setting

③

Tilt Swing

Activates and sets Swing monitoring in the Tilt direction and deletes data

·Setting
SSelects the preset swing position with the joystick and sets the position with the Enter key.

SPD is the speed with which the camera moves.(001~240°/sec)
DWL is the dwell time for the camera.(1~128sec)
Completes the setting by pressing the Enter key on the selected position.

·Execute

Starts swing monitoring.
Stops it with the Stop key.

·Clear

Deletes the swing data.

⑤

Group SEQ

Starts and sets Sequence monitoring and deletes the data. Registers up to 6 groups.

·Setting
Select the Preset Position to monitor using the joystick, and set the position using the Enter Key.
SPD is the speed with which the camera moves. (001~240°/sec)
DWL is the dwell time for the camera. (1~128sec)
Completes the setting by pressing the Enter key on the selected position.

·Execute

Starts Group monitoring.
Stops it with the Stop key.

·Clear

Deletes the group data.

④

Swing Focus Mode

This mode is for activating the Auto Focus during continuous operation of Pan or Tilt Swing.
Note) Excessively fast Pan or Tilt Swing may disrupt the Auto Focus.

·AUTO/MANUAL

AUTO activates the Auto Focus.

·For 0° Tilt in Wide mode, about a third of the object does not appear on the screen.
Some objects may appear whiter than the actual colors as a result of the AGC effect.

Notes

Tilt Swing

Execute
Clear

Setting

Press the
Enter key

Sequence Setting

Set Preset
Pan Swing
Tilt Swing
Swing Focus Mode MANUAL
Group SEQ
Tour SEQ
PTZ Trace
Power On Resume OFF

Tilt Swing

Group SEQ

Group 1
Group 2
Group 3
Group 4
Group 5
Group 6

Group 1

Press the

Enter key

Sequence Setting

Set Preset
Pan Swing
Tilt Swing
Swing Focus Mode MANUAL
Group SEQ
Tour SEQ
PTZ Trace
Power On Resume OFF

Swing Focus Mode

Sequence Setting

Set Preset
Pan Swing
Tilt Swing
Swing Focus Mode MANUAL
Group SEQ
Tour SEQ
PTZ Trace
Power On Resume OFF

Group SEQ

ENGLISH

39

SPEED DOME CAMERA

38

SPEED DOME CAMERA

⑥

Tour

Starts and sets Group monitoring and deletes the data.

•Setting

Selects the procedure for the registered Group Sequence with the joystick and sets it with the Enter key.
If an unregistered number is designated, the number cannot be entered.
Completes the setting by pressing the Enter key on the selected position.
SPD is the speed the camera moves. (001~240°/sec)
DWL is the dwell time for the camera.(1~128 sec)

•Execute

Starts Group monitoring.

•Clear

Deletes the Group monitoring data.

Camera setting

⑦

PTZ Trace

Memorizes and plays the manual control routes (Pan, Tilt, Zoom and Focus)

•Replay
Repeatedly plays the manual control routes
Stops it with the Stop key.

※If the control range is restricted to ① Pan Limit and ② Tilt Limit, the operation is not allowed beyond the

controlled range. Exercise caution.

•Memorize
While the manual setting is memorized in the internal memory for at least 120 seconds after this function is activated,

the memory time varies depending on the PTZ operation.
OVER means that the Memorize function is ended.

※ When the control range is restricted to ① Pan Limit and ② Tilt Limit, it is memorized.

⑧

Power On Resume

When the power supply is resumed after suspension due to power failure, the Sequence operation set before the
power failure is maintained.

Tour SEQ

Execute
Clear

Setting

Press the
Enter key

Sequence Setting

Set Preset
Pan Swing
Tilt Swing
Swing Focus Mode MANUAL
Group SEQ
Tour SEQ
PTZ Trace
Power On Resume OFF

Tour SEQ

PTZ Trace

Replay
Memorize

Replay

Press the
Enter key

Sequence Setting

Set Preset
Pan Swing
Tilt Swing
Swing Focus Mode MANUAL
Group SEQ
Tour SEQ
PTZ Trace
Power On Resume OFF

PTZ Trace

Sequence Setting

Set Preset
Pan Swing
Tilt Swing
Swing Focus Mode MANUAL
Group SEQ
Tour SEQ
PTZ Trace
Power On Resume OFF

Power On Resume

ENGLISH

41

SPEED DOME CAMERA

40

SPEED DOME CAMERA

Camera setting

Pan Limit

On/Off

Position

Press the
Enter key

3) P/T Setting

P/T Setting Menu

P/T Setting

Pan Limit
Tilt Limit
Area Setting
Area Masking
Home Position
Smart P/T ON
Auto Flip ON

Pan Limit

Tilt Limit

On/Off

Position

Press the
Enter key

P/T Setting

Pan Limit
Tilt Limit
Area Setting
Area Masking
Home Position
Smart P/T ON
Auto Flip ON

Tilt Limit

①

Pan Limit

Limits the range of movement in the PAN direction

•Position
Sets the range of movement. Determines the position measured from the left using the joystick and the Enter key. The

end position can be changed to the initial operation when power is resumed, depending on the setting position. This
represents normal operation.

•ON/OFF
Limit starts working when ON is selected.

②

Tilt Limit

Limits the range of movement in the Tilt direction.

•Position
Sets the range of movement. Determines the position measured from above using the joystick and the Enter key.

The end position can be changed to the initial operation when power is resumed depending on the setting position.
It is the normal operation.

•ON/OFF
Limit starts working when ON is selected.

Area Setting

Area 1
Area 2
Area 3
Area 4
Area 5
Area 6
Area 7
Area 8

Area 1

Press the
Enter key

P/T Setting

Pan Limit
Tilt Limit
Area Setting
Area Masking
Home Position
Smart P/T ON
Auto Flip ON

Area Setting

③

Area setting

Indicates the zone. Sets up to 8 areas.

•Area Name
Sets the area names. Up to 12 characters (English, Chinese, Numbers, etc.) can be entered using the joystick

and the Enter key. After input, put the area marks to SET using the joystick and press the Enter key. The setting
is then completed.

•Position

Sets the range of an area. Determines the position measured from the left using the joystick and the Enter key.
When the range of an area is overlapped, the area with the lower number indicates the overlapped area.

•ON/OFF

Sets the area display On or Off. This setting is valid from when a camera moves from the current area to another
area.

Set the OSD Setting ON. When the OSD Setting is OFF, this function doesn’t work. The default is OFF.

ENGLISH

43

SPEED DOME CAMERA

42

SPEED DOME CAMERA

④

Area Masking

The area to be excluded from the monitoring operation is displayed in white. Up to 8 areas can be set to be in white.

•Position
Select the scope of the display using the joystick and Enter Key.

•ON/OFF
Sets the area display function On or Off.

⑤

Home position

If any motion is detected within a certain period, the camera moves to the preset position.

•Setting
Sets the preset position number to which a camera moves, and when it moves.
Preset Position : 01 ~ 128
Time: 00~60 Min. (00 means 30 seconds)

•ON/OFF
Sets the activation of this function.

Camera setting

Home Position

On/Off

Press the
Enter key

P/T Setting

Pan Limit
Tilt Limit
Area Setting
Area Masking
Home Position
Smart P/T ON
Auto Flip ON

Home Position

Setting

P/T Setting

Pan Limit
Tilt Limit
Area Setting
Area Masking
Home Position
Smart P/T ON
Auto Flip ON

Smart P/T

⑥

Smart P/T

Changes the speed of PAN and TILT according to the zoom factor. In Tele, Pan/Tilt becomes slow. In Wide, Pan/Tilt
becomes fast. One rotation in Tele and Wide takes about 15 seconds and 3 seconds respectively.

⑦

Auto Flip

When Tilt is set to the 90°Limit using the joystick, and the setting is kept for a certain period, the Auto Flip
function makes PAN automatically rotate 180°and enables the Tilt area to be seen on the opposite side of the
screen.

With this function, the Tilt range is extended to 180°. For monitoring a moving object under a camera, activate
Auto Flip using the controller joystick, and you can monitor the object without the screen turning upside down
or reversing left to right.

P/T Setting

Pan Limit
Tilt Limit
Area Setting
Area Masking
Home Position
Smart P/T ON
Auto Filp ON

Auto Flip

Area Masking

Position
On/Off

Press the
Enter key

Press the
Enter key

P/T Setting

Pan Limit
Tilt Limit
Area Setting
Area Masking
Home Position
Smart P/T ON
Auto Flip ON

Area Masking

Position

Area Masking
Mask1
Mask2
Mask3
Mask4
Mask5
Mask6
Mask7
Mask8

Mask1

ENGLISH

45

SPEED DOME CAMERA

44

SPEED DOME CAMERA

Camera setting

4) OSD Setting

OSD Setting Menu

OSD Setting

Camera ID ON
Camera Name
Preset Number ON
Preset Name
Sequence Status ON
Area Name OFF

①

Camera ID

Sets the camera ID display.

②

Camera Name

·Edit
Sets the camera names using up to 12 characters in English (or Chinese), numbers and special characters.

·On/Off
Set whether to display a camera name.

Camera ID

OSD Setting

Camera ID ON
Camera Name
Preset Number ON
Preset Name
Sequence Status ON
Area Name OFF

Preset Number

OSD Setting

Camera ID ON
Camera Name
Preset Number ON
Preset Name
Sequence Status ON
Area Name OFF

Camera Name

Press the
Enter key

For editing, move the
cursor to Edit and press
the Enter key.

For editing, move the
cursor to Edit and press
the Enter key.

Camera Name

OFF

Edit

0123456789
ABCDEFGHIJKLMNOPQRSTUVWXYZ
abcdefghijklmnopqrstuvwxyz

！？▷◁▶◀【】()〈〉[]×＊＊÷＋－＝＿‖／○□
〜↑↓→←´˝,.·‥…；：¥＄¢£％＃＆

Chinese1 Back Space CLR SET

On/Off

Press the

Enter key

Preset Name

Edit

On/Off

③

Preset Number

Sets the preset numbers.

④

Preset Name

·Edit
Sets the preset names using up to 12 characters in English (or Chinese), numbers and special characters.

·On/Off
Set whether to display a preset name.

0123456789
ABCDEFGHIJKLMNOPQRSTUVWXYZ
abcdefghijklmnopqrstuvwxyz

！？▷◁▶◀【】()〈〉[]×＊＊÷＋－＝＿‖／○□
〜↑↓→←´˝,.·‥…；：¥＄¢£％＃＆

Chinese1 Back Space CLR SET

OSD Setting

Camera ID ON
Camera Name
Preset Number ON
Preset Name
Sequence Status ON
Area Name OFF

Preset Name

ENGLISH

47

SPEED DOME CAMERA

46

SPEED DOME CAMERA

Camera setting

⑥

Area Name

Sets the area names

✽ With the area name off, the area can’t be displayed.

⑤

Sequence Status

Sets the sequence groups

OSD Setting

Camera ID ON
Camera Name
Preset Number ON
Preset Name
Sequence Status ON
Area Name OFF

Sequence Status

OSD Setting

Camera ID ON
Camera Name
Preset Number ON
Preset Name
Sequence Status ON
Area Name OFF

Area Name

5) Alarm Setting

Alarm Setting Menu

Alarm Setting

OFF
Alarm Input
Alarm Out
Motion Detection

②

Alarm Input

Sets the Alarm Input Mode, Priority and Alarm Activation Method

·NC/NO/OFF
Selects NC, NO or OFF depending on the alarm sensor types.

·1~4 (Priority)
Sets the priority of four alarm inputs and reacts to the alarm input in accordance with the priority.

·Preset/Group/Tour Number
Sets the Preset, Group or Tour for reaction to the alarm input.
In case of alarm, moves to the Preset/Group/Tour/Off corresponding to each alarm. If there are several
alarms in sequence, stays in the Preset/Group/ Tour position during the Dwell Time according to the input
sequence. The pattern- linked alarm then carries out the relevant pattern motion in sequence.

①

Alarm Enable

To determine whether to activate the alarm, set to Alarm Enable.

·ON/OFF

The alarm is activated with ON.

Alarm Enable

Alarm Setting

Alarm Enable OFF
Alarm Input
Alarm Out
Motion Detection

Alarm Input

Alarm In[Mode P P/G/T No

INPUT1 OFF 1 OFF ***
INPUT2 OFF 1 OFF ***
INPUT3 OFF 1 OFF ***
INPUT4 OFF 1 OFF ***

Press the
Enter key

INPUT1

ENGLISH

Alarm Setting

Alarm Enable OFF
Alarm Input
Alarm Out
Motion Detection

49

SPEED DOME CAMERA

48

SPEED DOME CAMERA

Camera setting

③

Alarm Out

Matches each alarm input to one of two Alarm Outs

·OUT1 SET/OUT2 SET
Matches two alarm outputs to one of four alarm inputs and MD.

·OUT1 TIME/OUT2 TIME

Sets the ON/OFF and operating time in units of seconds, minutes or hours for two alarm outputs.
(1~59 sec., 1~59 min., 1~59 hours)

·OUT1 OFF/OUT2 OFF
When each alarm output is activated, select this function to forcibly release the alarm outputs. The alarm
output is then deactivated.

Alarm Out

Alarm Output

OUT1 SET 1 2 3 4 MD
OUT1 SET 1 2 3 4 MD
OUT1 TIME OFF 01 Sec
OUT2 TIME OFF 01 Sec
OUT1 OFF
OUT2 OFF

Press the
Enter key

OUT1 SET

④

Motion Detection

Motion Detection sets the motion detection function, areas to detect motion, and sensitivity of motion
detection. With Motion Detection on, the movements of an intruder can be detected. When motion is detected,
an alarm signal is sent to the Alarm Out.

·MD Execute
With Motion Detection On, moves to the preset position and then to On.

·Detect Area
Sets the area to detect.

- Whole : Detects motion on the whole screen.

- Upper : Detects motion on the upper side of the screen

- Lower : Detects motion on the lower side of the screen

- Center : Detects motion on the center of the screen

·Sensitivity

Sets the detection sensitivity. The higher the number, the smaller the motion the sensor reacts to.

·Preset No

Sets the preset number to which to move a camera when motion is detected.

WHOLE UPPER

LOWER CENTER

Alarm Setting

Alarm Enable OFF
Alarm Input
Alarm Out
Motion Detection

Motion Detection

Motion Detection

MD Execute
Detect Area WHOLE
Sensitivity 12
Preset No ***

Press the
Enter key

MD Execute

ENGLISH

51

SPEED DOME CAMERA

50

SPEED DOME CAMERA

Camera setting

6) Initialize Setting

①

Power On Reset

·Initialize a camera to the status prior to power supply

②

Factory Default Set

·Initialize to the factory default. Data such as preset is deleted. This function is used to initialize a variety of
settings. However, the digital zoom factor is not changed.

③

Camera Default Set

·When a single camera module is replaced due to a defect only in that camera, Camera Default Set is used to
set the replacement camera module to the setting of the previous camera.

④

Auto Refresh

·Optimize the built- in electrical circuit and the status of fixtures and devices in a camera at a pre-determined
interval (operating intervals can be set).
This is used for keeping, maintaining and correcting the camera settings when a camera directly faces a
specific light source, or the setting is not preserved because the camera has been rotating left, right, up and
down in a specific area for a long time.
The default is 7 Days.

·OFF, 1~7Days
Auto Refresh won’t run when OFF is selected. Select between 1~7 Days, and Auto Refresh will run at the
selected intervals.
Auto Refresh takes less than about 10 seconds.
The message “Auto Refresh” disappears when the operation is completed.

7) Status

Displays the dome camera setting.

Cam Model =22NC
Cam Version=03.05
Dome Version=01.00
Con Protocol=SAMSUNG
Dome ID=001
Controller=Type1-9600

Mounted Camera Model
Mounted Camera S/W Version
Control Board S/W Version
Setting Protocol
Dome Camera ID
Communication Mode Setting Status

Press the

Enter key

Main Menu

Camera Setting
Sequence Setting
P/T Setting
OSD Setting
Alarm Setting
Initialize
Status

Status

Cam Model =22NC
Cam Version=03.05
Dome Version=01.00
Con Protocol=SAMSUNG
Dome ID=001
Come Mode=DUPLEX
Factory Set=ON

Press the
Enter key

Main Menu

Camera Setting
Sequence Setting
P/T Setting
OSD Setting
Alarm Setting
Initialize
Status

Initialize

Initialize

Power On Reset
Factory Default Set
Camera Default Set
Auto Refresh 7Days

Power On Reset

ENGLISH

53

SPEED DOME CAMERA

52

SPEED DOME CAMERA

●

Dimension

●

Installation Method

Ceiling attached Type Installation Installation Method for embedded Type

※Other Installation Methods : You can use the camera in a variety of circumstances with accessories for outdoor

installation that you need to purchase separately. (See Page 17 and 20 for the
accessories that you can purchase)

Product Appearance and Installation Method

System configuration

1

SPD-2200

SVR-1630

SPD-2200

23 253

Power AC 24V

Ceiling

Ceiling

Power AC 24V

SVR-1630 (P/T Control Function)

Control Line
Video Line

SPD-2200 SPD-2200

ENGLISH

128mm

207.5mm

125.6mm

AC 24V

AC 24V

55

SPEED DOME CAMERA

54

SPEED DOME CAMERA

System configuration

SCC-3000

Receiver

16

1

2

3

64

Power
Supply

16

16

16

M 1

M 2

M 3

M 4

SVR-1630

SVR-1630

SVR-1630

SVR-1630

10

15

20

Control Line
Video Line

Specifications

Image Sensor 1/4-inch Color Interline-Transfer CCD. 410.000pixel
TV Type NTSC Type PAL Type
Total Pixels 811(V) × 508(H) 795(V) × 596(H)
Effective Pixels 768(V) × 494(H) 752(V) × 582(H)
Horizontal Scanning Frequency

15.734kHz 15.625kHz

Vertical Scanning Frequency

59.94kHz 50.00kHz
Synchronization Internal/External (AC Line Lock)
Video Output 1.0p-p/75Ω
S/N Ratio More than 48dB (AGC OFF)
Horizontal Resolution 480TV lines 460TV lines
Minimum Illumination 2.0Lux(Normal)/(@30IRE), 0.3Lux(Day & Night Mode)/(@30IRE)

0.03Lux(Slow-Shutter Mode)/(@30IRE)
Electronic Shutter Auto/Manual (1/60 ~ 1/10,000) Auto/Manual (1/50 ~ 1/10,000)
Slow-Shutter ON(x2~x128Fields) /OFF
Backlight Compensation ON/OFF
White Balance Auto/AWC/Manual/Outdoor/Indoor
Flickerless control Shutter speed fixed (1/100) Shutter speed fixed (1/120)
Iris Auto/Manual (Iris fix mode)
Gain control Auto/Manual
OSD Display ON/OFF
Aperture Compensation Level Controllable
Focal Length 3.9 ~ 85.8mm (Optic zoom 22x)
Digital Zoom 10x (Total 220x Zoom)
Max. Focal Ratio Wide 1:1.6 Tele 1:3.7
Covering Angle f=3.9mm 51.26°(H)×39.03°(V)f=85.8.mm 2.39°(H)×1.80°(V)
Min. Focus Distance 1.0m (Tele)~0.01m (Wide)
Pan Rotation Angle 360° Continuous
Pan Rotation Manual/Program
Pan Speed Manual : 0.5°/S~120°/s (64 levels) Preset : 0.5°/s~240°/s (64 levels)

Item

NTSC PAL

ENGLISH

56

SPEED DOME CAMERA

※ External Design and specification are subject to change without notice for improvement of product performance.

Cautions

●Samsung Techwin Inc. owns the copyright of this manual.

●This manual may not be reproduced in whole or in part, or transmitted in any form whatsoever, whether

electronic, mechanical or audio, without the written permission of Samsung Techwin.

●The contents of this manual may be revised for functional improvement at any time.

Specifications

Pan Resolution 0.05°
Pan Rotation Stop Accuracy

0.30°
Tilt Rotation Angle +0°~ 90°(Auto Flip to 180°available by Controller)
Tilt Rotation Manual/Program
Tilt Speed Manual : 0.5°/s~120°/s(64 levels) Preset : 0.5°/s~240°/s(64 levels)
Tilt Resolution

0.04°
Tilt Rotation Stop Accuracy

0.30°
Preset Position Max.128 points
Area Masking 8points
Alarm Alarm 4 Input

Alarm 2 OUT(Relay : NC/NO/COM,0.5A 125VAC,2A 30VDC Max)
Operating Temperature 0 ℃ ~ +50℃
Operating Humidity 20% ~ 75% (No Condensation)
Storage Temperature -20℃ ~ +60℃
Storage Humidity 20% ~ 95% (No Condensation)
Power Source, Voltage AC 24V ±10%
Power Consumption 8 Watts in standby, 13 Watts in operation
Dimensions ф128 ×207.5mm
Weight Approx. 1.8kg
Environment Indoor : Indoor Housing (STH-160PI), Indoor embedded Housing (STH-128PE)

Outdoor : Outdoor Housing (STH-160PO)
Wall Mount : STB-270PW
Ceiling Mount : STB-496PP

Item

NTSC PAL