Samsung SMV100T Users Manual

DRAFT

Internal Use Only

MOBILE HOTSPOT

BISCOTTO

This document is watermarked because certain important information in the document has not yet been verified. This document has been sent to you as a draft and for informational purposes only. The document should only be used for internal purposes and may not be distributed outside of Samsung, except to Samsung's carrier customer for testing purposes. Distributing the document outside of Samsung, except to Samsung's carrier customer for testing purposes could result in legal exposure to the company if the preliminary, unverified information in the draft turns out to be inaccurate.

User Manual

Please read this manual before operating your

phone and keep it for future reference.

DRAFT

Internal Use Only

Intellectual Property

All Intellectual Property, as defined below, owned by or which is otherwise the property of Samsung or its respective suppliers relating to the SAMSUNG Phone, including but not limited to, accessories, parts, or software relating there to (the “Phone System”), is proprietary to Samsung and protected under federal laws, state laws, and international treaty provisions. Intellectual Property includes, but is not limited to, inventions (patentable or unpatentable), patents, trade secrets, copyrights, software, computer programs, and related documentation and other works of authorship. You may not infringe or otherwise violate the rights secured by the Intellectual Property. Moreover, you agree that you will not (and will not attempt to) modify, prepare derivative works of, reverse engineer, decompile, disassemble, or otherwise attempt to create source code from the software. No title to or ownership in the Intellectual Property is transferred to you. All applicable rights of the Intellectual Property shall remain with SAMSUNG and its suppliers.

Open Source Software

Some software components of this product incorporate source code covered under GNU General Public License (GPL), GNU Lesser General Public License (LGPL), OpenSSL License, BSD License and other open source licenses. To obtain the source code covered under the open source licenses, please visit:

http://opensource.samsung.com

Disclaimer of Warranties; Exclusion of Liability

EXCEPT AS SET FORTH IN THE EXPRESS WARRANTY CONTAINED ON THE WARRANTY PAGE ENCLOSED WITH THE PRODUCT, THE PURCHASER TAKES THE PRODUCT "AS IS", AND SAMSUNG MAKES NO EXPRESS OR IMPLIED WARRANTY OF ANY KIND WHATSOEVER WITH RESPECT TO THE PRODUCT, INCLUDING BUT NOT LIMITED TO THE MERCHANTABILITY OF THE PRODUCT OR ITS FITNESS FOR ANY PARTICULAR PURPOSE OR USE; THE DESIGN, CONDITION OR QUALITY OF THE PRODUCT; THE PERFORMANCE OF THE PRODUCT; THE WORKMANSHIP OF THE PRODUCT OR THE COMPONENTS CONTAINED THEREIN; OR COMPLIANCE OF THE PRODUCT WITH THE REQUIREMENTS OF ANY LAW, RULE, SPECIFICATION OR CONTRACT PERTAINING

SM-VT100T_UM_English_MF8_PS_062713_D3

DRAFT

Internal Use Only

THERETO. NOTHING CONTAINED IN THE INSTRUCTION MANUAL SHALL BE CONSTRUED TO CREATE AN EXPRESS OR IMPLIED WARRANTY OF ANY KIND WHATSOEVER WITH RESPECT TO THE PRODUCT. IN ADDITION, SAMSUNG SHALL NOT BE LIABLE FOR ANY DAMAGES OF ANY KIND RESULTING FROM THE PURCHASE OR USE OF THE PRODUCT OR ARISING FROM THE BREACH OF THE EXPRESS WARRANTY, INCLUDING INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES, OR LOSS OF ANTICIPATED PROFITS OR BENEFITS.

Modification of Software

SAMSUNG IS NOT LIABLE FOR PERFORMANCE ISSUES OR INCOMPATIBILITIES CAUSED BY YOUR EDITING OF REGISTRY SETTINGS, OR YOUR MODIFICATION OF OPERATING SYSTEM SOFTWARE.

USING CUSTOM OPERATING SYSTEM SOFTWARE MAY CAUSE YOUR DEVICE AND APPLICATIONS TO WORK IMPROPERLY. YOUR CARRIER MAY NOT PERMIT USERS TO DOWNLOAD CERTAIN SOFTWARE, SUCH AS CUSTOM OS.

Samsung Telecommunications America (STA), LLC

Headquarters: 1301 E. Lookout Drive Richardson, TX 75082

Customer Care Center: 1000 Klein Rd. Plano, TX 75074 Toll Free Tel: 1.888.987.HELP (4357)

DRAFT

Internal Use Only

Internet Address:

http://www.samsung.com

2013 Samsung Telecommunications America, LLC. Samsung is a registered trademark of Samsung Electronics Co., Ltd.

Do you have questions about your Samsung Mobile Device? For 24 hour information and assistance, we offer a new FAQ/ARS System (Automated Response System) at:

www.samsung.com/us/support

microSD™ and the microSD logo are Trademarks of the SD Card Association. Wi-Fi is a registered trademark of the Wireless Fidelity Alliance, Inc. LTE is a trademark of ETSI

DRAFT

Internal Use Only

Table of Contents

Section 1: Getting Started .......................... 3

Understanding this User Manual . . . . . . . . . . . . 3

Setting Up Your Device . . . . . . . . . . . . . . . . . . . 4

Installing the Optional microSD Memory Card . . 9

Turning Your Device On and Off . . . . . . . . . . . 11

Factory Reset of Your Device . . . . . . . . . . . . . 11

Section 2: Understanding Your Device .... 12

Features of Your Device . . . . . . . . . . . . . . . . . 12

Front View . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Side Views . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

On-Screen Indicators . . . . . . . . . . . . . . . . . . . 14

Section 3: Connecting Your Device .......... 15

System Requirements . . . . . . . . . . . . . . . . . . 15

Before You Begin a Connection . . . . . . . . . . . 15

Initial Connection to Your Device . . . . . . . . . . 16

Accessing Your HotSpot via a Browser . . . . . . 16

Configuring Your HotSpot . . . . . . . . . . . . . . . . 17

Preparing your HotSpot for File Access . . . . . . 18

Connecting your Device to the HotSpot

via USB . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Factory Reset via the Web Portal . . . . . . . . . . 20

Section 4: Home Page ...............................21

Mobile HotSpot Home Page . . . . . . . . . . . . . . 21

Section 5: Network Page ...........................24

Mobile HotSpot Network Page . . . . . . . . . . . . 24

Wi-Fi Configuration . . . . . . . . . . . . . . . . . . . . 26

Section 6: Securing Your Device ..............27

Mobile HotSpot Security Page . . . . . . . . . . . . . 27

SIM PIN Tab . . . . . . . . . . . . . . . . . . . . . . . . . . 27

MAC Filtering Tab . . . . . . . . . . . . . . . . . . . . . . 28

Port Filtering Tab . . . . . . . . . . . . . . . . . . . . . . 30

Port Forwarding Panel . . . . . . . . . . . . . . . . . . 31

Section 7: Configuring Your Device ..........33

Mobile HotSpot Configuration Page . . . . . . . . 33

Settings Tab . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Software Update Tab . . . . . . . . . . . . . . . . . . . 35

DLNA Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

DRAFT

Internal Use Only

Tools Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . .36

Factory Reset of Your Device via Portal . . . . . . 37

Section 8: Messaging on Your Device ......38

Mobile HotSpot Messaging Page . . . . . . . . . . .38

Section 9: Health and Safety Information 40

Exposure to Radio Frequency (RF) Signals . . . .40

Specific Absorption Rate (SAR) Certification

Information . . . . . . . . . . . . . . . . . . . . . . . . .40

FCC Part 15 Information to User . . . . . . . . . . .42

Radio Frequency (RF) Energy . . . . . . . . . . . . . . 42

Knowing Radio Frequency Safety . . . . . . . . . . 42

FCC Radio Frequency Emission . . . . . . . . . . . .43

Samsung Mobile Products and Recycling . . . .43

UL Certified Travel Charger . . . . . . . . . . . . . . . 44

Battery Use and Safety . . . . . . . . . . . . . . . . . .45

Care and Maintenance . . . . . . . . . . . . . . . . . .47

Operating Environment . . . . . . . . . . . . . . . . . . 47

Restricting Children's Access to Your

Wireless Mobile Device . . . . . . . . . . . . . . . .50

FCC Notice and Cautions . . . . . . . . . . . . . . . . . 50

Other Important Safety Information . . . . . . . . .50

Section 10: Warranty Information ............52

Standard Limited Warranty . . . . . . . . . . . . . . .52

End User License Agreement for Software . . . .57

Index ...........................................................65

DRAFT

Internal Use Only

Section 1: Getting Started

Understanding this User Manual

The sections of this manual is laid out to assist your with setup and follow the UI features of your device.

A robust index for features begins on page 65. Also included is important safety information, beginning on

page 40, that you should know before using your device. This manual gives navigation instructions according to the

default display settings. Before using your device for the first time, you’ll need to

install and charge the battery and install the micro SIM card. The micro SIM card is loaded with your subscription details,

such as your PIN, a vailable optional services, and many other features.

Unless otherwise specified, all instructions in this manual assume you are starting from the Home screen.

Note:

Instructions in this manual are based on default settings, and may vary from your device, depending on the software version on your device, and any changes to the device’s Settings.

Unless stated otherwise, instructions in this User Manual start with the device at the Home screen.

All screen images in this manual are simulated. Actual displays may vary, depending on the software version of your device and any changes to the device’s firmware.

Getting Started 3

DRAFT

Internal Use Only

Special Text

Throughout this manual, you’ll find text that is set apart from the rest. These are intended to point out important information, share quick methods for activating features, to define terms, and more. The definitions for these methods are as follows:

•

Notes

: Presents alternative options for the current feature, menu,

or sub-menu.

•

Tips

: Provides quick or innovative methods, or useful shortcuts.

•

Important

: Points out important information about the current

feature that could affect performance.

•

Warning

: Brings to your attention important information to prevent loss of data or functionality, or even prevent damage to your phone.

Text Conventions

This manual provides condensed information about how to use your phone. To make this possible, the following text conventions are used to represent often-used steps:

➔

Note:

Arrows are used to represent the sequence of selecting successive options in longer, or repetitive, procedures.

From the Web portal home screen, select ➔ Messaging tab.

Setting Up Your Device

These steps take you through an out-of-the-box setup process. These procedures are intended to help you get your device setup, activated, and assist you with your initial connection.

DRAFT

Internal Use Only

Removing the Back Cover

Release Latch

1. Hold the device firmly and locate the cover release

latch (1).

2. Place your fingernail in the groove and firmly “pop” the

cover off the device (2).

Important!

Installing the 4G LTE microSIM Card

Before removing or replacing the battery cover, make sure the device is switched off. To turn the device off, hold down the key until the power-off image displays, then tap



With the battery cover removed, carefully slide the microSIM card into the SIM card slot until it “clicks” into place with the label side facing up.

Power off

Important!

The 4G LTE microSIM Card MUST remain in the device when in use.

Getting Started 5

DRAFT

Internal Use Only

Caution!

Do not bend or scratch your microSIM Card. Avoid exposing it to static electricity, water, or dirt.

Removing the 4G LTE microSIM Card

1. Remove the battery and cover (page 7).

2. Carefully slide the 4G LTE SIM card out of the SIM card

socket.

Installing the Battery

Your device is powered by a rechargeable, standard Li-Ion battery. A Wall/USB Charger (Charging Head and USB cable) are included with the device, for charging the battery.

Note:

The battery comes partially charged. You must fully charge the battery before using your device for the first time. After the first charge, you can use the device while charging.

Important!

If you experience any issues with your device, contact Customer Service at XXX??????? or visit your nearest U.S. T-Mobile

If your SIM card is ever separated from the device

or damaged, your device will not function.

retail location.

Important!

Before removing or replacing the battery cover, make sure the device is switched off. To turn the device off, hold down the key until the power-off image displays, then tap

1. Insert the battery as shown, making sure to align the

gold contacts (1).

2. Press down gently to secure the battery (2).

Power off

DRAFT

Internal Use Only

Removing the Battery

Installing Battery

Removing Battery



Grip the battery at the top end (3) and lift it up and out of the battery compartment (4).

Replacing the Back Cover

1. Position the battery cover over the battery

compartment (1).

2. Press down firmly along the edges of the cover (2).

Getting Started 7

DRAFT

Internal Use Only

Charging the Battery

Charging Head

USB Cable

Your device is powered by a rechargeable Li-ion battery. A wall charger, which is used for charging the battery, is included with your device. Use only approved batteries and chargers. Ask your local Samsung dealer for further details.

Before using your device for the first time, you must fully charge the battery.

Note:

Verify that the battery is installed prior to connecting the wall charger. If both the wall charger is connected and the battery is not installed, the device can power cycle continuously and prevent proper operation. Failure to unplug the wall charger before you remove the battery, can cause the device to become damaged.

Important!

It is recommended you fully charge the battery before using your device for the first time.

1. Connect the USB cable to the charging head.

2. Locate the Charging port.

3. Insert the USB cable into the device’s Charger/

Accessory jack.

4. Plug the charging head into a standard AC power

outlet. The device turns on and indicates both its charge state and percent of charge.

DRAFT

Internal Use Only

Warning!

Charging port

mini USB Cable

While the device is charging, if the screen does not function due to an unstable power supply unplug the USB power adapter from the power outlet or unplug the USB cable from the device.

5. When charging is finished, first unplug the charger’s

power plug from the AC wall outlet, then disconnect the charger’s connector from the device.

Installing the Optional microSD Memory Card

Note:

The installation of an optional microSD card can provide additional storage and access to additional files such as document, image, and other multimedia content.

1. Using your fingertip (1), slide the mini USB connector

out from its current location (2).

Getting Started 9

DRAFT

Internal Use Only

2. Pull the cable all the way round the unit (3) and then

USB slot

microSD card slot

carefully remove the other USB connector from its slot (4). This action exposes the internal microSD card slot.

3. Slide the memory card into the card slot until it “clicks”

into place.

4. Replace the USB cable firmly into its corresponding

slot.

5. Pull the cable around the side of the device and

carefully re-insert the mini USB cable back into its corresponding slot.

DRAFT

Internal Use Only

Turning Your Device On and Off

Turning Your Device On



Press and hold (

Turning Your Device Off



With the device on, press and hold ( turn the device off.

Power

) to turn the device on.

Power

) to

Factory Reset of Your Device

Resetting your device restores all factory defaults. You may need to reset your device if you cannot connect device(s) to your Wi-Fi HotSpot or can not regain access to the Web portal.

Power

and

WPS

1. Locate the

device.

2. Press and hold these two buttons for 10 seconds. Once

completed, the power should recycle and the main screen will re-appear.

buttons along the top of the

Getting Started 11

DRAFT

Internal Use Only

Section 2: Understanding Your Device

This section outlines key features of your device. It also describes the device’s keys, screen and the icons that display when the device is in use.

Features of Your Device

Your device is lightweight, easy-to-use and offers many significant features. The following list outlines a few of the features included in your device.

•

Delivers data speeds faster than the current 3G network technology by using 4G LTE

•

Wi-Fi ® Capability

•

Able to receive and send text messages via Web Portal

•

Expandable memory slot - supports up to XXX???GB microSD

•

Portable Wi-Fi HotSpot and USB Tethering-capability

Front View

The following illustrations show the main elements of your device. The following list correlates to the illustrations.

Notification bar

connection status, signal strength, battery level, and time, and displays notifications about incoming messages, calls and other action

shows information about the

DRAFT

Internal Use Only

Display

shows all the information needed to operate your device, such as the connection status, received signal strength, battery level, connected number of devices, data usage, and time.

USB Connector

USB-capable devices using this connector type.

provides a direct connection for

Side Views

The following illustration shows the side elements of your device:

Power key

1. WPS key

a WPS connection. The WPS (Wi-Fi Protected Setup) feature allows you to pair your WAP-capable device without the need for entering a passcode. This process is similar to Wi-Fi Direct pairing.

Charging Port

power cable.

Caution!

Please use only an approved charging accessory to charge your device. Improper handling of the charging port, as well as the use of an incompatible charger, may cause damage to your device and void the warranty.

ends switches the phone off and on.

allows you to pair with devices currently using

allows you to connect a compatible

Mini USB Connector

to devices using this type of connector. This provides your target device with wired Internet access.

microSD Card Slot

card to expand the memory of your device.

provides a mini USB for connection

(internal) allows you use a microSD

Understanding Your Device 13

DRAFT

Internal Use Only

USB Connector

devices using this type of connector. This provides your target device with wired Internet access.

provides a USB plug for connection to

On-Screen Indicators

Displays your current signal strength. The greater the number of bars, the stronger the signal.

Indicates there is no signal available.

Displays when there is no microSIM card in the device.

Displays your current battery charge level. Icon shown is fully charged.

Displays your battery is currently charging.

Shows your current battery only has up to 4% power remaining and will soon shutdown. (Charge: ~4% - 1%).

Displays when connected to the 3G network.

Displays when your device is connected to and communicating with the 3G network.

Displays when connected to the HSPA+ network.

Displays when connected to and communicating with the HSPA+ network.

Displays when your device is communicating with the 4G LTE network.

Displays when Wi-Fi is active and indicates the number of externally connected devices.

Displays when there is a new text message.

Displays your current data usage.

DRAFT

Internal Use Only

Section 3: Connecting Your Device

With your new Wi-Fi HotSpot and your computer, a wireless Internet connection can always be at your fingertips.

System Requirements

If you choose to connect with an external device via a direct USB cable connection, your target device will need the meet the following minimum system requirements:

•

One open Type-A USB Port (ex: Laptops, Desktops, etc..)

•

One open mini USB Port (ex: portable devices, mobile phones, etc..)

Note: The USB Data cable is for charging only

Note:

It is recommended the battery be fully charged in order to use your device via Wi-Fi for the first time, or connect your device to the AC wall charger for power.

Before You Begin a Connection



Press and hold ( The following should occur once your device turns on:

•

The battery indicator shows a solid green color (if there is more than a 20% charge.)

•

Once your device has been activated, it automatically connects to the Internet provided that your cellular network broadband service is available.

•

Confirm a network indicator icon, such as , appears in the Notification area at the top of the display. This indicates the device is in service and ready to connect.

Power

) to turn the device on.

Connecting Your Device 15

DRAFT

Internal Use Only

Initial Connection to Your Device

Username: XXXXXXXXX Password: XXXXXXXXX URL: mobile.hotspot.com

Use

rnam

: XXXXX

XXX

sword:

XXX

XXXXX

URL: m

obile.hotspot.com

1. Locate the internal sticker that provides both the

Username and password information for access to the device’s portal.

2. Enable the Wi-Fi connection on your target device and

begin to scan for available Wi-Fi networks.

3. The VT100 HotSpot appears as a secured device

named: “

T-Mobile Broadband ##

4. Enter the default password located on the sticker to

establish your initial connection.

”.

Note:

The default password is also the last 8-digits of the device IMEI.

78901234

For example: If the IMEI number is “123456

”,

the password is “78901234”.

Accessing Your HotSpot via a Browser

1. With your device now connected to the HotSpot, launch

an available Browser on your target device.

2. Within the Browser’s Address field, enter either:

• mobile.hotspot.com

• 192.168.43.1:8080/

3. From the HotSpot’s main Web portal, locate the Password

field.

4. Enter the HotSpot’s Administrator (Web portal) password information and click

Note:

The default Administrator password is “

Note:

The default connection state for the HotSpot is secured. Use the Web portal to configure the various settings.

Apply

admin

”.

DRAFT

Internal Use Only

Configuring Your HotSpot

Changing your Web Portal Administrator Password

Changing this password prevents other users from entering the default “admin” password and gaining access to your Web portal and changing the device’s settings.

1. Access the Web portal and select the Too ls

tab.

2. Select the password information.

3. Re-enter your new password within the Password

Caution!

4. Click

New Password

field.

Write down this new administrator password. If you loose or forget it, you will need to do a Factory Reset on the device to regain access. For more information, refer to “Factory Reset of Your Device” on page 11.

Apply

field and enter your updated

Configuration

Verify New

➔

Changing your Wi-Fi Access Password

This password is different from the administrator password that provides access to the Web portal. The Wi-Fi password is used by external devices to gain a connection to the HotSpot.

Network

1. Access the Web portal and select

2. From the bottom of the screen, tap the

and enter your new password.

3. Click

Apply

. Any currently connected devices will need

to update their connection passwords.

Password

field,

Changing your SSID Name

1. Access the Web portal and select

2. Select the

3. Delete the current information and enter a new name.

4. Click

to forget their previous connections and reconnect to the newly named HotSpot.

Network Name (SSID)

Apply

. Any currently connected devices will need

Connecting Your Device 17

Network

field.

DRAFT

Internal Use Only

Assigning Data Limits

1. Access the Web portal and select

2. Tap the

3. Tap the adjacent field, enter a numeric value, and

4. Click

Hiding Your HotSpot

1. Access the Web portal and select

2. From the bottom of the screen, tap the

3. Tap the checkbox field again to re-enable SSID

Data Limits

select either GB (Gigabytes) or MB (Megabytes).

Apply

an on-screen notification will appear.

checkbox. Removing the checkmark stops

enable

broadcasting your SSID.

broadcast.

checkbox to enable the feature.

. Once you reach your assigned data limit,

Network

Broadcast SSID

Preparing your HotSpot for File Access

1. Access the Web portal and select (

2. Scroll down the page and enable the

option.

device(MTP)

3. Click

4. Follow the USB connection procedures described on

page 19.

Files can also be accessed from the internal microSD memory card by enabling the DLNA functionality. For more information, refer to “DLNA Tab” on page 35.

Media

Home

+ 49 hidden pages