Samsung SMT-190P, SMT-171N, SMT-171P, SMT-190N User Manual

TFT-LCD MONITOR

SMT-171N/SMT-171P SMT-190N/SMT-190P

User’s Manual

Please read this manual thoroughly before use, and keep it handy for future reference.

SMT-171/SMT-190-ENG 2005.12.6 4:30 PM Page 1

USER’S MANUAL

- 2 -

IMPORTANT SAFETY INSTRUCTIONS

1. Read these instructions.

2. Keep these Instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers,stoves, or other apparatus (including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles and the point where they exit from the apparatus.

11. Only use attachment/accessories specified by the manufacturer.

12.

Use only with the cart, stand, tripod, bracket or table specified by the manufacturer or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or when unused for long periods of time.

14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped.

- The apparatus shall not be exposed to dripping or splashing and that no objects

filled with liquids, such as vases , shall be placed on the apparatus.

Minimum distances (e.g. 10cm) around the apparatus for sufficient ventilation

“WARNING - To reduce the risk of fire or electric shock, do not expose the apparatus to rain or moisture.”

“The apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the apparatus.”

SMT-171/SMT-190-ENG 12/8/05 9:40 AM Page 2

USER’S MANUAL

- 3 -

Graphic Symbol Explanation

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated ‘dangerous voltage’ within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

Warning - To Prevent Fire or Shock Hazard,

Do Not Expose This Monitor To Rain or Moisture.

1. Read Instructions : All the safety and operating instructions

should be read before the appliance is operated.

2. Retain Instructions : The safety and operating instructions should

be retained for future reference.

3. Heed Warnings : All warnings on the monitor and in the operating

instructions should be adhered to.

4. Follow Instructions : All operating and user instructions should be

followed.

5. Cleaning : Unplug this monitor from the wall outlet before cleaning.

Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. Exception. A monitor that is meant for uninterrupted service and that for some specific reason, such as the possibility of the loss of an authorization code for a CATV converter, is not intended to be unplugged by the user for cleaning or any other purpose may exclude the reference to unplugging the monitor in the cleaning description otherwise required in Item 5.

6. Attachments : Do not use attachments not recommended by

Samsung as they may cause hazards.

7. Water and Moisture : Do not use this monitor near water for

example, near a bathtub, wash bowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool and the like wet basement or near a swimming pool and the like.

8. Accessories : Do not place this monitor on an unstable cart,

stand, tripod, bracket or table. The monitor may fall, causing s erious injury to a child or adult and serious damage to the appliance. Use only with a cart, stand, tripod. bracket or table recommended by Samsung, or sold with the monitor. Any mounting of the monitor should follow Samsung’s instructions and should use a mounting accessory recommended by Samsung.

9. Ventilation :Slots and openings in the cabinet are provided for

ventilation and to ensure reliable operation of the monitor and to protect it from overheating and these openings should never be blocked by placing the monitor on a bed, sofa, rug or other similar surface. This monitor should never be placed near or over a radiator or heat register. This monitor should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or Samsung’s instructions have been adhered to.

10. Power Sources : This monitor should be operated only from the

type of power source indicated on the making label. If you are not sure of the type of power supply to your installation site, consult your Samsung dealer or local power company.

11. Grounding or Polarization : For monitors equipped with a 3-wire

grounding-type plug having a third(grounding) pin. This plug will only fit into a grounding type power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the grounding-type plug.

12. Power : Cord Protection-Power supply cords should be routed so

that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the monitor.

13. Lightning : For added protection for this monitor during a

lightning storm or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the cable system. This will prevent damage to the monitor due to lightning and power-line surges.

14. Overloading : Do not overload wall outlets and extension cords

as this can result in a risk of fire of electric shock.

15. Object and liquid Entry : Never push objects of any kind into

this monitor through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the monitor.

16. Servicing : Do not attempt to service this monitor yourself as

opening or removing cover may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

17. Damage Requiring Service : Unplug this monitor from the wall

outlet and refer servicing to qualified service personnel under the following conditions. a. When the power-supply cord or plug is damaged. b. If liquid has been spilled or objects have fallen into the monitor. c. If the monitor has been exposed to rain or water. d. If the monitor does not operate normally by following the oper-

ating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and require extensive work by a qualified technician to restore the monitor to its normal operation.

If the monitor has been dropped or the cabinet has been

damaged.

f. When the monitor exhibits a distinct change in performance-this

indicates a need for service.

CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE REAR COVER. NO USER SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL.

CAUTION

RISK OF ELECTRIC

SHOCK DO NOT OPEN

IMPORTANT SAFEGUARDS

Caution

Power source is indicated on the rear of the set. It contains high-voltage parts. If you remove the cover, it may cause fire or electric shock. Do not remove the cover by yourself. (Control switches are at the front of the monitor.)

SMT-171/SMT-190-ENG 12/8/05 9:40 AM Page 3

USER’S MANUAL

- 4 -

18. Replacement Parts : When replacement parts are required,

be sure the service technician has used replacement parts specified by Samsung or have the same characteristics as

the original parts. Unauthorized substitutions may result in fire, electric shock or other hazards.

19. Safety Check : Upon completion of any service or repairs to

thismonitor, ask the service technician to preform safety

checks to determine that the monitor is in proper operating

condition.

Warning

This equipment has been tested and found to comply the limits for a class A digital device, pursuant to part 15 of the FCC Rules and ICES-003 of Industry Canada. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generate, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

User-Installer Caution

Your authority to operate this FCC verified equipment could be voided if you make changes or modifications not expressly approved by the party responsible for compliance to part 15 of the FCC Rules.

Information to user

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions : (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. If necessary, consult your dealer or an experienced

radio/television technician for additional suggestions. You may find the booklet called how to Identify and Resolve Radio/TV Interference Problems helpful. This booklet was prepared by the Federal Communications Commission. It is available from the U.S. Government Printing Office, Washington, DC 20402, Stock Number 004-000-00345-4.

IC Compliance Notice

This Class (A) digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.

This Class A digital apparatus complies with Canadian ICES-003.

Warning This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

NOTICE

NOTICE Hg (Within a circle) LAMP(S) INSIDE THIS PRODUCT CONTAIN MERCURY AND BE RECYCLED OR DISPOSED OF ACCORDING TO LOCAL, STATE OR FEDERAL LAWS For details see lamprecycle.org,eire.org,or call 1-1800-Samsung

SMT-171/SMT-190-ENG 12/8/05 9:40 AM Page 4

USER’S MANUAL

- 5 -

Contents

IMPORTANT SAFETY INSTRUCTIONS

IMPORTANT SAFEGUARDS

Contents

Unpacking

Names and Functions of Parts

Connecting to External Devices

Setup Menu Configurations

Appendix

Troubleshooting Guide

WEEE Symbols

SMT-171/SMT-190-ENG 12/8/05 9:40 AM Page 5

USER’S MANUAL

Unpacking

- 6 -

Remove the package cover and place the product on a flat and secure surface or in the installation location. Check whether all the following devices and accessories are included with the main system.

Front Key Control

1. SOURCE /

Select input source, and move the previous menu.

2. MENU

Activates and exits the On Screen Display. OSD MENU(MAIN) : Input, Picture, OSD, Setup.

3. AUTO /



(DOWN)

This button is move the OSD menu, and use to auto adjustment of VGA input only.



(UP)

Move the OSD main menu or sub menu.

(LEFT)

This button is decrease the level of active function, and move the previous menu.



(RIGHT)

This button is increase the level of active function, and select OSD menu.

7. IR Sensor

Remote controller sensor.

8. POWER ON/OFF

Turns the power ON or OFF. There will be a few seconds delay before the display appears. The power LED(next to the power switch) lights with

green when the power is turned ON. The power is turned off by pressing the power switch again and the power LED goes off.

Bottom Panel Control

1. DC 12V IN

DC power Input.

2. VGA IN

VGA Signal Input.

3. VIDEO A IN

Composite signal Input for VIDEO A

4. VIDEO A OUT

Video looping output for VIDEO A

5. VIDEO B IN

Composite signal Input for VIDEO B

6. VIDEO B OUT

Video looping output for VIDEO B

7. S-VIDEO (Y/C) IN

Y/C separated signal input

8. S-VIDEO (Y/C) OUT

Y/C separated signal looping output

Names and Functions of Parts

TFT-LCD MONITOR USER’S MANUAL POWER CORD

AC POWER ADAPTOR

BATTERIES REMOTE CONTROLLER VGA SIGNAL CABLE

1 2 3 4 5 6

7 8

8 7 6 5 4 3

2 1

SMT-171/SMT-190-ENG 12/8/05 9:40 AM Page 6

USER’S MANUAL

- 7 -

Remote Controller

1. POWER( )

Turns the power ON or OFF. There will be a few seconds delay before the display appears.

2. ID RESET

Reset the system id of remote controller. (Default system id is ‘1’)

3. P.MODE

Select Picture mode in Video. (Dynamic / Standard / Movie / Custom)

4. AUTO

Auto geometry adjustment in VGA Source.

5. RETURN

Return to the previous menu.

6. MENU

Activates and exits the On Screen Display.

7. LEFT / RIGHT (

¥/)

Increases or decreases the level of active function, and right button is to select OSD menu, left button is previous OSD menu.

8. UP / DOWN (

/

)

Move to OSD menu.

9. NUMBER Button

Change the SYSTEM ID for remote controller. With the SYSTEM ID button pressed, entered the desired NUMBER by pressing the corresponding button(0~9) to set up the Remote Controller ID

10. SYSTEM ID

Set the system id of remote controller.

11. BRIGHT, CONTRAST, COLOR, SHARPNESS

Simply control brightness, contrast, color, sharpness via the

remote controller.

12. INFO

Display information of the picture.

13. SOURCE

Select VGA or Video (Video A / Video B / S-Video) sources.

14. ENTER

Select OSD main menu or sub menu.

The product can be connected to an external device such as Camera, DVR,VCR, etc.

NO SIGNAL DISPLAY

When there is no connection at the VGA and Video input, the On Screen Display will show this message.

OSD MENU DESCRIPTION

MENU SELECTION

1. Press the MENU button and then

/

button to display each

menu.

2. Press the ENTER or  button and then

/

button to select

the menu item.

3. Press the MENU button to return to normal picture.

NOTE : If you don’t connect to VGA port, menu is not displayed

in VGA mode.



A. INPUT MENU

Connecting to External Devices

Setup Menu Configurations

VCR Camera B Camera A DVR

VGA

Check Input Signal

Video A

Input

Source List :

Video A

Video B

S-Video VGA

Move Enter Exit

(

) 1

# $ % ^

SMT-171/SMT-190-ENG 12/8/05 9:40 AM Page 7

외부입력2

DVD/비디오TIME SLIP 녹화

채널

프로그래시브 스캔

VCRDVD

복사

USER’S MANUAL

- 8 -

Inputs can be set to Video A, Video B, S-Video, VGA mode.

Press the MENU button and then / button to select the Input menu.

2. Press the ENTER or  button to select the Source List.

3. Press the ENTER or  button and then / button to select the input source.

4. Press the ENTER button to change the input source.

You can also select the input source with SOURCE on the Remote Control.



B. PICTURE MENU (Video mode)

Mode

1. Press the MENU button and then

/ button to select the

Picture menu.

2. Press the ENTER orbutton to select the Mode.

3. Press the ENTER orbutton and then / button to

select the picture mode.

4. Press the ENTER button to save.

You can also recall a desired picture mode with P.MODE on the Remote Controller.

Custom

- NTSC input

- PAL input

1. Press the ENTER or  button to select Custom in the Picture menu.

2. Press the / button and then ENTER or  button to select the adjustment item you need.

EX) If you select the Brightness, then the picture below appears

on the screen.

3. Press the

¥/

button to increase or decrease level.

4. Press the / button to select the other item.

5. Press ENTER button to save.

You can also recall a desired Brightness, Contrast, Color or Sharpness with BRIGHT, CONTRAST, COLOR or SHARPNESS on the Remote Control.

NOTE : Tint item is NTSC input only.



C. PICTURE MODE (VGA)

Adjustment

Video A

Picture

Mode : Dynamic Custom

Move Enter Exit

Video A Picture

Mode :

Custom

Dynamic

Standard

Movie Custom

Move

Enter Exit

Video A

Picture

Move Enter Exit

Mode : Dynamic



Custom



Video A

Custom

Move Enter Exit

Brightness : 50



Contrast : 50



Color : 50



Sharpness : 50



Tint : 50



VGA

Picture

Move

Enter

Exit

Adjustment



Color Tone : Normal



User



VGA

Picture

Move

Enter Exit

Brightness : 50



Contrast : 50



Clock : 40



Phase : 12



H.Position : 50



V.Position : 50



Video A

Custom

Move Enter Exit

Brightness : 50



Contrast : 50



Color : 50



Sharpness : 50





Brightness



VGA

Picture

Move Enter

Exit

Adjustment



Color Tone : Normal



User



SMT-171/SMT-190-ENG 12/8/05 9:40 AM Page 8

+ 17 hidden pages