Samsung SMO-XAAV, SMO-151QN-XAAV User Manual

EZ View Kit:Remote Monitoring

Video Surveillance SYSTEM

SMO-151QN/XAAV

User Guide

IMPORTANT SAFETY INSTRUCTIONS

1. Read these instructions.

2. Keep these Instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance with the

manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers,

stoves, or other apparatus (including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug.

A polarized plug has two blades with one wider than the other.

A grounding type plug has two blades and a third grounding prong.

The wide blade or the third prong are provided for your safety.

If the provided plug does not fit into your outlet consult an electrician for

replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at

plugs convenience receptacles and the point where they exit from the

apparatus.

11. Only use attachment/accessories specified by the manufacturer.

12. Use only with the cart, stand, tripod, bracket,

or table specified by the manufacturer or sold

with the apparatus. When a cart is used, use

caution when moving the cart/apparatus

combination to avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or when unused for long

periods of time.

14. Refer all servicing to qualified service personnel. Servicing is required

when the apparatus has been damaged in any way such as power-supply

cord or plug is damaged liquid has been spilled or objects have fallen into

the apparatus the apparatus has been exposed to rain or moisture does not

operate normally or has been dropped.

Eng-2

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT

REMOVE COVER (OR BACK). NO USER SERVICEABLE

PARTS INSIDE. REFER SERVICING TO QUALIFIED

SERVICE PERSONNEL.

Graphic Symbol Explanation

The lightning flash with arrowhead symbol within an

equilateral triangle is intended to alert the user to the

presence of uninsulated ‘dangerous voltage’ within the

product’s enclosure that may be of sufficient magnitude to

constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is

intended to alert the user to the presence of important

operating and maintenance (servicing) instructions in

the literature accompanying the appliance.

CAUTION

Warning - To Prevent Fire or Shock Hazard, Do Not

Expose This Monitor To Rain or Moisture.

Eng-3

IMPORTANT SAFEGUARDS

Caution

Power source is indicated on the rear of the set. It contains high-voltage parts.

If you remove the cover, it may cause fire or electric shock. Do not remove the

cover by yourself. (Control switches are at the front of the monitor.)

1. Read Instructions : All the safety and operating instructions should be

read before the appliance is operated.

2. Retain Instructions : The safety and operating instructions should be

retained for future reference.

3. Heed Warnings : All warnings on the monitor and in the operating

instructions should be adhered to.

4. Follow Instructions : All operating and user instructions should be

followed.

5. Cleaning : Unplug this monitor from the wall outlet before cleaning.

Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for

cleaning.

Exception. A monitor that is meant for uninterrupted service and that for

some specific reason such as the possibility of the loss of an

authorization code for a CATV converter is not intended to be

unplugged by the user for cleaning or any other purpose may exclude the

reference to unplugging the monitor in the cleaning description

otherwise required in Item 5.

6. Attachments : Do not use attachments not recommended by Samsung

as they may cause hazards.

7. Water and Moisture : Do not use this monitor near water for example

near a bathtub wash bowl kitchen sink or laundry tub in a wet basement

or near a swimming pool and the like wet basement or near a swimming

pool and the like.

Eng-4

8. Accessories : Do not place this monitor on an unstable cart, stand,

tripod, bracket or table. The monitor may fall causing serious injury to a

child or adult and serious damage to the appliance. Use only with a cart,

stand, tripod. bracket or table recommended by Samsung or sold with

the monitor. Any mounting of the monitor should follow Samsung’s

instructions and should use a mounting accessory recommended by

Samsung.

9. Ventilation : Slots and openings in the cabinet are provided for

ventilation and to ensure reliable operation of the monitor and to protect

it from overheating and these openings should never be blocked by

placing the monitor on a bed, sofa, rug, or other similar surface. This

monitor should never be placed near or over a radiator or heat register.

This monitor should not be placed in a built-in installation such as a

bookcase or rack unless proper ventilation is provided or Samsung’s

instructions have been adhered to.

10. Power Sources : This monitor should be operated only from the type of

power source indicated on the making label. If you are not sure of the

type of power supply to your installation site consult your Samsung

dealer or local power company.

11. Grounding or Polarization : For monitors equipped with a 3-wire

grounding-type plug having a third(grounding) pin. This plug will only

fit into a grounding type power outlet. This is a safety feature. If you are

unable to insert the plug into the outlet contact your electrician to

replace your obsolete outlet. Do not defeat the safety purpose of the

grounding-type plug.

12. Power : Cord Protection-Power supply cords should be routed so that

they are not likely to be walked on or pinched by items placed upon or

against them paying particular attention to cords at plugs convenience

receptacles and the point where they exit from the monitor.

Eng-5

13. Lightning : For added protection for this monitor during a lightning

storm or when it is left unattended and unused for long periods of time,

unplug it from the wall outlet and disconnect the cable system. This will

prevent damage to the monitor due to lightning and power-line surges.

14. Overloading : Do not overload wall outlets and extension cords as this

can result in a risk of fire of electric shock.

15. Object and liquid Entry : Never push objects of any kind into this

monitor through openings as they may touch dangerous voltage points or

short-out parts that could result in a fire or electric shock.

Never spill liquid of any kind on the monitor.

16. Servicing : Do not attempt to service this monitor yourself as opening or

removing cover may expose you to dangerous voltage or other hazards.

Refer all servicing to qualified service personnel.

17. Damage Requiring Service : Unplug this monitor from the wall outlet

and refer servicing to qualified service personnel under the following

conditions.

a. When the power-supply cord or plug is damaged.

b. If liquid has been spilled or objects have fallen into the monitor.

c. If the monitor has been exposed to rain or water.

d. If the monitor does not operate normally by following the operating

instructions. Adjust only those controls that are covered by the

operating instructions as an improper adjustment of other controls

may result in damage and require extensive work by a qualified

technician to restore the monitor to its normal operation.

e. If the monitor has been dropped or the cabinet has been damaged.

f. When the monitor exhibits a distinct change in performance-this

indicates a need for service.

Eng-6

18. Replacement Parts : When replacement parts are required be sure the

service technician has used replacement parts specified by Samsung or

have the same characteristics as the original parts.

Unauthorized substitutions may result in fire electric shock or other

hazards.

19. Safety Check : Upon completion of any service or repairs to this

monitor ask the service technician to preform safety checks to determine

that the monitor is in proper operating condition.

FCC & ICES Information

Warning

This equipment has been tested and found to comply the limits for a class A

digital device pursuant to part 15 of the FCC Rules and ICES-003 of

Industry Canada. These limits are designed to provide reasonable protection

against harmful interference when the equipment is operated in a commercial

environment. This equipment generate uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instruction

manual may cause harmful interference to radio communications. Operation

of this equipment in a residential area is likely to cause harmful interference

in which case the user will be required to correct the interference at his own

expense.

User-Installer Caution

Your authority to operate this FCC verified equipment could be voided if

you make changes or modifications not expressly approved by the party

responsible for compliance to part 15 of the FCC Rules.

Eng-7

Information to user

Changes or modifications not expressly approved by the party responsible

for compliance could void the user's authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits

for a Class A digital device pursuant to Part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful

interference when the equipment is operated in a commercial environment.

This equipment generates uses and can radiate radio frequency energy and if

not installed and used in accordance with the instruction manual may cause

harmful interference to radio communications. Operation of this equipment

in a residential area is likely to cause harmful interference in which case the

user will be required to correct the interference at his own expense.

This device complies with Part 15 of the FCC Rules. Operation is subject to

the following two conditions: (1) this device may not cause harmful

interference and (2) this device must accept any interference received

including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible

for compliance could void the user's authority to operate the equipment. If

necessary consult your dealer or an experienced radio/television technician

for additional suggestions. You may find the booklet called How to Identify

and Resolve Radio/TV Interference Problems helpful. This booklet was

prepared by the Federal Communications Commission. It is available from

the U.S. Government Printing Office Washington, DC 20402, Stock Number

004-000-00345-4.

Eng-8

The party responsible for product compliance:

SAMSUNG ELECTRONICS CO., LTD.

America QA Lab of Samsung

3351 Michelson Drive,

Suite #290, Irvine, CA92612 USA

IC Compliance Notice

This Class (A) digital apparatus meets all requirements of the Canadian

Interference-Causing Equipment Regulations.

Cet appareil numérique de la classe (A) respecte toutes les exigences du

Règlement sur le matériel brouilleur du Canada.

This Class A digital apparatus complies with Canadian ICES-003.

Cet appareil numéique de la classe A est conforme à la norme NMB-003 du

Canada.

Warning

This is a class A product. In a domestic environment this product may cause

radio interference in which case the user may be required to take adequate

measures.

Eng-9

IMPORTANT SAFETY INSTRUCTIONS .................................. 2

IMPORTANT SAFEGUARDS..................................................... 4

FCC & ICES Information.............................................................. 7

Chapter 1: System Components and Installation

1-1)

Environmental requirements for installation and safety

1-2) System Components............................................................. 13

1-3) STANDARD CAMERA composition

and installation method ....................................................... 14

1-4) NIGHTVISION CAMERA

SOC-N120 INTRODUCTION)

(

1-5) External terminal connecting method for

CAMERA and MONITOR.................................................. 22

1-6) Whole System connection and configuration ...................... 23

............................................ 19

.......... 12

Chapter 2: MONITOR FRONT PANEL KEY Function and

Using Method

2-1) TALK KEY.......................................................................... 26

2-2) AUD/SP SEL KEY ...............................................................26

2-3) VOL+/VOL- KEY ............................................................... 26

2-4) SCREEN SAVE- KEY ........................................................ 27

2-5) ALARM RESET- KEY ........................................................27

2-6) QUAD/PAGE- KEY ............................................................ 27

2-7) LIVE/VCR- KEY..................................................................27

2-8) PIP- KEY ..............................................................................28

2-9) FREEZE- KEY .....................................................................28

2-10) SEQUENCE- KEY ............................................................ 28

2-11) ZOOM- KEY ..................................................................... 28

2-12) POWER- KEY ................................................................... 28

2-13) ENTER- KEY .................................................................... 28

2-14) UP/DOWN KEY............................................................... 29

2-15) LEFT/RIGHT KEY........................................................... 29

Eng-10

Chapter 3: Setting each item function at SETUP MENU

3-1) ADJUST MENU function and setting method .................... 30

3-2) DATE/TIME MENU Function setting ................................ 31

3-3) DWELL TIME MENU function setting .............................. 31

3-4) DISPLAY MENU function setting ..................................... 32

3-5) TITLE MENU Function setting............................................33

3-6) ALARM MENU Function setting........................................ 34

3-7) NETWORK SETUP function and setting method............... 35

3-8) MONITOR basic setting(SMO-151QN).............................. 43

3-8-1) “LIVE” MENU.............................................................. 45

3-8-2) System Configuration Menu.......................................... 58

3-8-3) Network Configuration Menu........................................ 66

3-8-4) Moniter Set up ............................................................... 75

3-8-5) Utilities .......................................................................... 76

3-9) VIEW EVENT LOG MENU function and

setting method ...................................................................... 88

Chapter 4: DISPLAY MODE setting method

4-1) SINGLE SCREEN DISPLAY ............................................. 89

4-2) QUAD MODE DISPLAY ................................................... 90

4-3) AUTO SEQUENTIAL DISPLAY MODE .......................... 91

4-4) PIP MODE DISPLAY ......................................................... 92

4-5) ZOOM MODE DISPLAY ....................................................93

Chapter 5: Each Product feature

Product Specification....................................................................94

SOC-C120 : Standard Camera................................................94

SOC-N120 : Night Vision Camera ........................................ 95

OBSERVATION MONITOR ..................................................... 96

NETWORK ................................................................................. 97

Appendix A) Software up data .................................................... 99

Appendix B) IP Router Setup Guide ......................................... 100

Step-by-step Examples of IP Router.................................. 101

Eng-11

Chapter 1: System Components and Installation

1-1) Environmental requirements for installation and safety

This section describes the environmental requirements for safe installation and use.

Install the product on a flat table or in a rack. It should be used only when level and should not be

used when stood vertically or obliquely. The location in which the main system is installed and the

configuration of the wiring room are very important for proper operation of the system.

When the products are installed too closely together or the location is poorly ventilated, the system

may not operate properly and maintenance of the system may be difficult. Sufficiently circulate the

air within the system operating room and tightly fasten the cover of the main system to prevent

malfunction and reduce system downs due to environmental causes.

There are high voltage parts inside. Do not arbitrarily open the cover.

Install the product in a place that meets the following environmental conditions. Be sure to maintain

the system under the temperatures and humidity conditions given below:

• Operating temperature: 0°C ~ 40°C

• Storage temperature: -20°C ~ 60°C

• Operating humidity: 20% ~ 85% RH

•Storage humidity: 20% ~ 95 RH

• Input voltage: AC 120V

• Power usage: less than 110 Watts

• Frequency: 60Hz

Caution

When operating the product, the fluctuation of input voltage must be within 10% of the rated voltage

and the external power outlet must be grounded, otherwise, it may cause electric shock or malfunction

of the product. Do not connect heat-generating appliances such as a hair dryer, iron or refrigerator to the

same power outlet in which the product is plugged, otherwise it may cause a fire or malfunction of the

product. The use of an Automatic Voltage Regulator (AVR) is highly recommended to ensure that

stable power is supplied. Be sure to coil CORE-FERRITE on the connector to reduce electro-magnetic

interference (EMI).

Eng-12

1-2) System Components

The system consists of the following:

STANDARD

MONITOR

CAMERA

BRACKET

ITEM

MONITOR

STANDARD CAMERA

NIGHT VISION CAMERA

CAMERA BRACKET

CAMERA CABLE

INSTALLATION MANUAL

POWER CORD

VCR CABLE

SENSOR CONNECTOR

ETHERNET CABLE

• Check whether all the following devices and accessories are included with the main system.

POWER CODE &

INSTALLATION MANUAL

CAMERA

(SOC-C120)

MODEL

SMO-151QN

SOC-C120

SOC-N120

SBR-110S

MCB-60

DESCRIPTION

15" FLAT CRT MONITOR

NORMAL TYPE CAMERA

STAND TYPE BRACKET

6PIN SHIELD CABLE

NIGHT VISION

CAMERA

(SOC-N120)

CAMERA

CABLE

SENSOR

CONNECTOR

Q’ty

NOTE

Tapping Screw 6

60ft(1ft=0.3048m)

VCR CABLE

ETHERNET

CABLE

Eng-13

1-3) STANDARD CAMERA

composition and installation method

1) Standard Camera composition (SOC-C120)

a. Lens

It has a focal length of 3.8mm and makes it possible for you to observe a relatively wide

area.

PIN NUMBER SPEC

SPEAKER(HOT)

VIDEO_OUT

GND

SPEAKER(COLD)

AUDIO_OUT/ALARM_OUT

18V DC

b. Microphone

Capable of picking up all sound in the vicinity of the camera location and transmitting to

the monitor.

c. Camera fitting groove

Enables the camera to be fixed onto the bracket. You may install it either above or below

the camera if necessary.

d. 6-pin modular jack

Used to connect the camera to the monitor.

e. SENSOR jack

Used to connect the sensor to the camera.

Eng-14

f. Speaker

It outputs the sound signal which was transfered from the monitor.

2) INSTALLING STANDARD CAMERA (SOC-C120)

SOC-C120 camera can be attached to the wall, ceiling or shelf using the camera mount bracket

(SBR-110S).

Choose an installation site that can sufficiently support the weight of the equipments to be installed.

Attach the camera mount bracket to the wall or ceiling using the supplied three screws (M4 X L15).

Adjust the camera to target the video location and tighten the bracket handle on the camera mount

bracket.

4x15 sized screws

wall or ceiling

Eng-15

3) CAMERA MOUNT BRACKET(SBR-110) & STANDARD CAMERA(SOC-C120)

(1) Overview

CAMERA MOUNT BRACKET (SBR-110S) is used to attach the camera to a wall, ceiling or shelf.

(2) Specifications

Use : Indoor

Installation : Wall or Ceiling

Dimensions : 57 (W) X 47.2(H) X 100.5(L)

Weight : 150g

°C

~ 50

Operating Temperature : -10

(3) Accessories

SCREW (M4 X L15) : 3 pcs

(4) Installation

Explains the installation of CAMERA MOUNT BRACKET as wall as the installation of the camera

onto the CAMERA MOUNT BRACKET.

•

Choose an installation site that can sufficiently support the weight of the equipments to be

installed.

•

Attach the camera mount bracket to the wall using the supplied screws (M4 X L15).

°C

Eng-16

•

Adjust the camera to target the video location and tighten the bracket handle on the camera

mount bracket. Install the camera on to the male screw of the Camera Mount Bracket by

rotating the camera in clockwise.

•

Loosen the handle by turning it in a counter clockwise direction and then adjust the camera

position . Tighten the handle, turning it clockwise, and lock the camera in position.

•

Connect the camera cable to the camera.

Handle

Eng-17

After positioning monitor and installing four cameras to a desired location, please connect

CAMERA to MONITOR through CAMERA CABLE (MCB-60) as shown in the below

figure. Please check whether or not it is properly connected.

Connection status checking method :

• Turn on the monitor after connecting cameras, and check if camera image is displayed.

The initial screen mode of monitor is quad mode.

In case monitor and camera is not connected, OSD ‘L’(LOSS) will be displayed on screen.

•

Eng-18

1-4) NIGHT VISION CAMERA

1) Before Installation

SOC-N120 INTRODUCTION

SOC-N120 Nightvision camera is intended to be used exclusively with those sold by this

company for DIY.

With the built-in IR LED and light sensor in the camera, both day monitoring and night

monitoring are possible. Also, since it is designed as water-proof daily product, it can be

used not only indoors, but also outdoors.

2) Precautions for Installation and Operation

Installing SOC-N120

* Make sure the installation location is a place where 5 times (about 1 kg) of the total

weight of the cam-era can be tolerated before installing the camera.

* When installing the camera, make sure the cable is not squeezed in an inappropriate

place or the insu-lation plastic is removed (it will be a cause for malfunction or fire).

* Keep personnel away from under the installation location because there is a risk of

object falling during in stallation. Move precious items to a safe place as well before

the installation.

* Install SOC-N120 in a cool place where there is no direct sunlight.

* Do not expose SOC-N120 to direct sunlight during operation or storage.

* SOC-N120 should always be used in a place where certain temperature and humidity

can be main-tained (as specified below).

- Temperature: 14°F ~ 122°F

- Humidity: Below 90%

Eng-19

3) Installation

1. Make sure the installation location is a place

where 5 times (about 2.2lbs) of the total weight

of the camera can be tolerated before installing

the camera.

2. Connect the cable below the camera after

attaching the provided Mount Bracket to the

desired place.

3. Use the handle on the Mount Bracket to adjust

the direction you want to setup for monitoring.

SOC-N120 Pin Configuration

1 SP-

VIDEO_OUT

3 GND

4 SP+

5 ALM/AUDIO

6 VDD

Eng-20

4) Nom des composantes

a). Lens

- It has a focal length of 3.8mm and makes it possiblefor you to observe a relatively wide area.

b). Illumination Sensor

- Detects incoming light to control the IR LED.

c). IR LED

- This is an infrared LED that is controlled by the illumination sensor.

d). Camera fitting groove

- Enables the camera to be fixed onto the bracket. You may install it either above or

below the camera if necessary.

e). Speaker

- Used to connect the sensor to the camera.

f). SENSOR jack

- It outputs the sound signal which was transfered from alarm sensor.

g). Microphone

- Capable of picking up all sound in the vicinity of the camera location and transmitting to

the monitor.

h). 6-pin modular jack

- Used to connect the camera to the monitor or DVR.

Eng-21

1-5) External terminal connecting method for CAMERA and

MONITOR

1) External terminal connecting method for CAMERA

Camera alarm injack

Sensor in put

PIR Sensor

•

An additional PIR sensor or external sensor can also be connected.

•

The additional PIR sensor can be connected as shown in the above graphic.

•

Sensor’s trigger signal is NO (Normal Open).

•

Sensor is not supplied. (Sold separately)

Sensor

2) VIDEO OUT BNC (1~4) terminals connecting method of monitor rear

VIDEO OUT BNC1 ~ BNC4 terminals in the rear of the monitor are VIDEO terminals for outputting

video images from OBSEVATION CAMERA to THROUGH OUT.

BNC VIDEO output terminal can be used to connect to VCR (TIME LAPSE) or SLAVE MONITOR.

3) VCR or ALARM terminal connecting method

TIME LAPSE VCR OR NORMAL VCR

VIDEO IN

AUDIO IN AUDIO OUT

VIDEO OUT VIDEO IN

AUDIO OUT AUDIO IN

VIDEO OUT

NOT USED

a) Connect the VCR cable to the VCR terminal on the rear panel.

b) Connect the VIDEO OUT plug to the VIDEO IN terminal of the VCR.

c) Connect the VIDEO IN plug to the VIDEO OUT terminal of the VCR.

d) Connect the AUDIO OUT plug to the AUDIO IN terminal of the VCR.

e) Connect the AUDIO IN plug to the AUDIO OUT terminal of the VCR.

Eng-22Eng-22

f) Not Used

g) Connect the A/O (HOT) terminal on the rear panel to the Alarm IN terminal of the VCR.

h) Connect the A/O (COLD) terminal on the rear panel to the Ground terminal of the VCR.

i) Connect the A/R terminal on the rear panel to the Alarm Reset terminal of the VCR.

j) Connect the G (ground) terminal on the rear panel to the Ground terminal of the VCR.

1-6) Whole System connection and configuration

Eng-23Eng-23

VCR (Time Lapse)Rear

Total System Configuration

Eng-24

Local System Configuration

Connect LAN cable of Cable/ADSL modem or Direct Fixed/Static IP LAN Line to WAN port of IP Router.

2. Connect LAN ports of IP Router(1~4 or 1~8) to Ethernet port SMO-151QN to be set up and to Ethernet port of

Local PC to use during setup.

3. Connect Video cable of Camera to MONITOR.

4. Turn on the MONITOR power.

Notice

If you have a Static (Fixed) IP line or Dynamic IP line (Cable Modem or ADSL Modem) with one IP address (whether its

dynamic or fixed), but have more than one internet device to use (such as a PC and a SMO-151QN or several SMO-151QN);

you must use an IP Router (different from a simple Network Hub); you must set up the Router to work with the SMO-151QN;

and you must use a network capable PC within the local Router network to do the setup.

If you are using an existing Router which is already set up, you may not need to redo the basic setup of the Router agian, but it

is highly recommended that you at least read all the instructions below and go through the steps.Whether you are using an

existing Router or a new Router, you must go through the Port Forwarding portion of the setup.

Eng-25

Chapter 2: MONITOR FRONT PANEL KEY

Function and Using Method

Front Panel

2-1) TALK KEY

TALK KEY allows users to transmit voice signal to intended camera by inputting voice with built-in

MIC in the front of the monitor. For this function, select a target camera with the ▲/▼ key on the

FRONT PANEL, and press AUD/SP SEL KEY. At this time, if a voice signal is generated through the

MIC with the TALK KEY pressed, the signal will be transmitted to the camera.

2-2) AUD/SP SEL KEY

AUD/SP SEL KEY allows users to select a camera to exchange voice signals with the monitor at

QUAD DISPLAY MODE. At QUAD DISPLAY MODE, select target camera display by using

▲/▼ , and press AUD/SP SEL KEY. Then “S” OSD will be displayed on the selected

screen. If you want to exchange voice signals with another camera, use▲/▼ key again to select the

camera display, and press AUD/SEL KEY. Then, “S” OSD will be displayed and users can exchange

voice signals with the monitor.

2-3) VOL+/VOL- KEY

Allows users to decrease or increase voice signal generated from the monitor.

VOL+ : Increase sound volume from the monitor.

VOL- : Decrease sound volume from the monitor.

Eng-26Eng-26

2-4) SCREEN SAVE - KEY

Allows users to set SCREEN SAVE MODE of monitor. PICTURE screen is off when the SCREEN

SAVE KEY is pressed, Users can exit from SCREEN SAVE MODE by pressing SCREEN SAVE

BUTTON again under picture “OFF” status. SCREEN SAVE MODE is automatically cancelled and

picture is “ON” when an event such as an alarm or loss at SCREEN SAVE MODE occurs.

2-5) ALARM RESET- KEY

Alarm function can be cancelled while the alarm is working.

2-6) QUAD/PAGE- KEY

Allows users to display QUAD -A or QUAD - B at QUAD DISPLAY MODE.

•

QUAD - A: QUAD DISPLAY MODE from Camera 1 to Camera 4

•

QUAD - B: QUAD DISPLAY MODE from Camera 5 to Camera 8

2-7) LIVE/VCR- KEY

Allows users to switch LIVE MODE to VCR MODE or VCR MODE to LIVE MODE. If VCR MODE

is cancelled, the QUAD picture of LIVE MODE will be automatically displayed. In case any event

happens at VCR MODE such as ALARM, the MODE will be automatically switched to LIVE MODE,

and the pre-set operation for the event will be carried out. If there is no external input at VCR MODE,

the OSD “NO SIGNAL” will be displayed.

•

LIVE MODE: Image and voice signal from CAMERA is displayed.

•

VCR MODE: External image and voice signal from VCR terminal from the rear of the monitor is

displayed.

Eng-27Eng-27

2-8) PIP- KEY

Can be used to see the main screen while Single screen is displayed. The main screen can be changed

and transfered to another channel while PIP is working. Please refer to "CHAPTER 4. DISPLAY

MODE setting method(Eng-86)" for PIP function and details.

2-9) FREEZE- KEY

This key allows users to see a target camera picture at PAUSE MODE. If users select the camera with

the ▲/▼ KEY, and press the FREEZE BUTTON, the OSD “ I I ” will be displayed on pause picture

from the camera. Other FRONT KEY input is ignored at FREEZE MODE, and other FRONT KEY

inputs will be available only after the FREEZE MODE is cancelled.

2-10) SEQUENCE- KEY

It makes a picture switch sequentially. This means that display the picture will be displayed during the

DWELL TIME pre-set at the DWELL MENU of SETUP MENU, and switch the picture automatically

as a pre-set sequence. Please refer to 3-3) DWELL TIME MENU function and setting (Eng-35) for

details of DWELL TIME setting.

2-11) ZOOM- KEY

It zooms a part of a picture doubling it in the display. If the ZOOM BUTTON is pressed, zoom area

will be displayed. Users can move to a target area by using ▲/▼ KEY at this time. If ¥ENTER

SWITCH is pressed at the target area, the area will be displayed with 2 times larger.

2-12) POWER- KEY

It turns ON/OFF the power of the monitor and camera at the same time.

In case the monitor power is ON, LED of monitor front is lit and the monitor is displayed in color bar

pattern. For a while, the OSD “SYSTEM INITIALIZED...” will be displayed with blue pattern during

twenty eight second - s or so.

Eng-28Eng-28Eng-28

2-13) ENTER- KEY

Enter key allows users to

1.Enter set up menu movement and setting mode

2.Display single camera picture

2-14) UP/DOWN KEY

Allows users to

1.Change camera channel

2.Select set up menu movement and setting mode

UP: Increase items

DOWN: Decrease items

2-15) LEFT/RIGHT KEY

Allows users to set date

LEFT: Decrease Date

RIGHT: Increase Date

Eng-29Eng-29

Chapter 3: Setting each item function at SETUP

Pressing the MENU BUTTON of the FRONT PANEL allows users to enter SETUP MENU and see the

following menu OSD box. Setting method of each SETUP MENU function and operation is as follows.

06/01/03 13:14:00

SETUP MENU

1. ADJUST

2. DATE/TIME

3. DWELL TIME

4. DISPLAY

5. TITLE

6. ALARM

7. NETWORK SETUP

8. VIEW EVENT LOG

3-1) ADJUST MENU function and setting method

•

Function: Allows adjustment to the display status

•

Setting method: Move to #1. ADJUST MENU by using▲/▼ KEY and press the ENTER

SWITCH to display the OSD as shown in the figure below. (The figure shows the initial setting

status.)

06/01/03 13:14:00

ADJUST SETTING

CONTRAST 50 BRIGHT 50 COLOR 50 SHARPNESS 50 TINT 50

VE_1.07

Move to a target item by using ▲/▼ KEY.

Enter the item by pressing the ¥ENTER SWITCH.

At this time, set a target value by using ▲/▼KEY.

You can move to another item by using▲/▼ KEY after setting the target value.

(1) CONTRAST : Adjusts light and shade of screen

(2) BRIGHT : Adjusts lightness of entire screen

(3) COLOR : Adjusts color density

(4) TINT : Adjusts color sense

(5) SHARPNESS : Adjusts contour of screen

Eng-30Eng-30

+ 75 hidden pages

Samsung SMO-XAAV, SMO-151QN-XAAV User Manual

IMPORTANT SAFETY INSTRUCTIONS

IMPORTANT SAFEGUARDS

FCC & ICES Information

Contents

Chapter 1: System Components and Installation

1-1) Environmental requirements for installation and safety

1-2) System Components

1-3) STANDARD CAMERA

1-4) NIGHT VISION CAMERA

1-6) Whole System connection and configuration

2-1) TALK KEY

2-2) AUD/SP SEL KEY

2-3) VOL+/VOL- KEY

2-4) SCREEN SAVE - KEY

2-5) ALARM RESET- KEY

2-7) LIVE/VCR- KEY

2-8) PIP- KEY

2-9) FREEZE- KEY

2-10) SEQUENCE- KEY

2-11) ZOOM- KEY

2-12) POWER- KEY

2-13) ENTER- KEY

2-14) UP/DOWN KEY

2-15) LEFT/RIGHT KEY

3-1) ADJUST MENU function and setting method