Samsung SM-316B User Manual

COMBO DRIVE
SM-316

User's Guide

FCC Compliance

This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception,
which can be deter-mined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:

Re-orient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

Contents

2

Safety Precautions

3

ENGLISH

The following diagrams illustrate the precautions to be taken when using
your COMBO drive.

✱ Changes or modifications not expressly approved by the party responsible for

compliance could void the user’s authority to operate the equipment.

You must not use the drive in any manner other than that specified in this guide.

Avoid exposing your eyes or skin to direct or scattered radiation.

CAUTION

Do not attempt to repair the COMBO drive yourself.
Contact your dealer or local SAMSUNG representative for all repairs.
If you make any adjustments or perform any operations other than those
specified in this guide, you run the risk of exposure to hazardous radiation.

WARRANTY

Please refer to the Samsung limited warranty statements.

PRECAUTIONS

1. To reduce the risk of fire or electric shock, do not expose this
appliance to rain or moisture.

2. Always check each disc for cracks before using it. If there are
cracks on the surfaces, especially around the border of the center
hole, we recommend that you make a copy of the disc immediately
and then stop using it. If you continue using the disc, it will probably
develop more cracks and eventually cause irreparable damage.

3. Do not use poor quality discs:

From unknown sources
Without any copyright
Scratched or damaged in any way

Safety Precautions 3
Your COMBO Drive 4
Upgrading the Firmware Flash Memory 5
System Requirements 5
Installing the COMBO Drive 6
Connecting the Cables 6
Installing the CD Record Utility 9
Installing the Device Driver 9
Setting Up the Device Driver 10
Recommended Disc Types 10
Using the COMBO Drive 11
Storing and Cleaning Your Discs 11
Solving Recording Problems 12
Caution with errors 14
Term Description 15
Recommended Disc Type 15
General DMA Installation Guide 15
Solving Technical Problems 16
Technical Specifications 18

* All product names mentioned in this document are trademarks or

registered trademarks of their respective owners.

ENGLISH

5

Upgrading the Firmware Flash MemoryYour COMBO Drive

4

1. Connector for stereo headphones with a 3.6 mm stereo mini-jack

2. Headphone volume control

3. Disc compartment (the compartment opens and closes automatically
when you press the Eject button)

4. Emergency eject hole (if the compartment does not open when
you press the Eject button, power off the computer, insert a pin or
unfolded paper clip in the hole and push firmly)

5. Indicator light

6. Eject button

The product firmware can be upgraded by downloading the updated file from the
following Web site:

http:// www.samsungodd.com

www.samsungelectronics.com

System Requirements

Before you install the COMBO drive, we strongly recommend that you check that
your setup meets the system requirements listed below.

Item Description

Computer Intel Pentium II 300MHz/Celeron 333A(or higher),

32 MB of RAM (or higher) with an IDE interface

Free expansion unit 5.25 inch

Disk space 700 MB minimum

Windows version Windows 95/98/2000/ME/XP/NT4.0 OSR2 (or higher)

(For Windows NT, we recommend Service Pack2,
and Version is over 4.00.1381)

MS-DOS 5.0 or higher (For MS-DOS, The CD-R/CD-RW driver

can only read a disc without premaster Software.)

DVD Video playback PC with Windows 95/98/2000/ME/XP/NT4.0 OSR2

DVD-Video playback software and appropriate
hardware (the Power DVD MPEG software is
included in the COMBO drive package)

1. Two-pin digital audio output terminal for use with a sound or MPEG card
supporting digital audio features

2. Four-pin sound output terminal for use with a sound card
(refer to the sound card documentation for further details)

3. Master/slave select terminal

4. 40pin host E-IDE interface connector

5. 4pin power terminal

12 3 456

1

23 4

5

DVD Region Protection Coding (RPC):

The RPC feature is supported on DVD players and is used with DVD-video discs
(such as movies). Currently, the motion picture industry has divided the world into
different regions or zones that correspond to the regional markets into which the
motion picture industry releases movies. Simply put, RPC codes are placed on movies
marketed throughout the world, based on the region of the world in which they are
being sold. These RPC codes help control and prevent pirating of new movies into
other motion picture regions prior to their true release dates within those markets.

The SM-316 COMBO drive supports RPC phase II. In the RPC-2 mode, the local
code can be changed by users.
RPC-2 is selected by default for the SM-316 COMBO drive.
You can change the region code up to five times via an MPEG application.

Please contact your dealer or local SAMSUNG representative if you wish to change
the local code more than five times.