Samsung SLVD570H Users Manual

2-671-543-11 (1) US/ES

DVD Player/ Video Cassette Recorder

Operating Instructions

Manual de instrucciones

For customers in the USA If you have any questions about your Sony DVD-VCR, you may call Sony Customer Information Center at 1-800-VHS-SONY (847-7669).

For all other Sony product questions, please call Sony Customer Information Center at 1-800-222-SONY (7669). Or write to: Sony Customer Information Center 12451 Gateway Boulevard Ft. Myers, FL 33913

For Customers in Canada If this product is not working properly, please call 1-877-602-2008 for Peace of Mind Warranty Replacement service. For other product related questions please contact our Customer Information Service Center at 1-877-899-7669 or write to us at: Customer Information Service 115 Gordon

Baker Road, Toronto, Ontario, M2H 3R6

SLV-D570H

Sony Corporation Printed in China AK68-00927A

WARNING

To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only.

CAUTION

The use of optical instruments with this product will increase eye hazard. As the laser beam used in this DVD player is harmful to eyes, do not attempt to disassemble the cabinet.

Refer servicing to qualified personnel only.

This symbol is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

For customers in the U.S.A

Owner’s Record

The model and serial numbers are located at the rear of the unit. Record the serial number in the space provided below. Refer to them whenever you call upon your Sony dealer regarding this product.

Model No. ______________ Serial No.______________

CAUTION

You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment.

Note

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are desi gned to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: – Reorient or relocate the

receiving antenna.

– Increase the separation between

the equipment and receiver.

– Connect the equipment into an

outlet on a circuit different from that to which the receiver is connected.

– Consult the dealer or an

experienced radio/TV technician for help.

Notes about discs

• To keep the disc clean, handle the disc by its edge. Do not touch the surface.

• Do not expose the disc to direct sunlight or heat sources such as hot air ducts, or leave it in a car parked in direct sunlight as the temperature may rise considerably inside the car.

• After playing, store the disc in its case.

• Clean the disc with a cleaning cloth. Wipe the disc from the center out.

• Do not use solvents s uch as benzine, thinner, commercially available disc/lens cleaners, or antistatic spray intended for vinyl LPs.

• If you have printed the disc’s label, dry the label before playing.

WARNING

Precautions

On safety

• To prevent fire or shock hazard, do not place objects filled with liquids, such as vases, on the apparatus.

• Should any solid object or liquid fall into the cabinet, unplug the player and have it checked by qualified personnel before operating it any further.

On power sources

• Operate the unit only on 120 V AC, 60 Hz.

• This unit is not disconnected from the AC power source (mains) as long as it is connected to the wall outlet, even if the unit itself has been turned off.

• Unplug the unit from the wall outlet if you do not intend to use it for an extended period of time. To disconnect the cord, pull it out by the plug, never by the cord.

On placement

• Do not install the unit in a confined space such as a bookshelf or similar unit.

• Do not install the unit in an inclined position. It is designed to be operated in a horizontal position only.

• Keep the unit, discs and cassettes away from equipment with strong magnets, such as microwave ovens or large loudspeakers.

• Do not place heavy objects on the unit.

On operation

• When you move the player, take out any discs. If you don’t, the disc may be damaged.

• If the unit is brought directly from a cold to a warm location, or is placed in a very damp room, moisture may condense on the lenses inside the player and cause damage to the video head, tape, and the optical block. Should this occur, the player may not operate properly. When you first install the player, or when you move it from a cold to a warm location, remove the disc and tape and leave the player turned on for about three hours before operating the player.

On adjusting volume

Do not turn up the volume while listening to a section with very low level inputs or no audio signals. If you do, the speakers may be damaged when a peak level section is played.

On cleaning

Clean the cabinet, panel and controls with a soft cloth slightly moistened with a mild detergent solution. Do not use any type of abrasive pad, scouring powder or solvent, such as alcohol or benzine.

On cleaning discs, disc/lens cleaners

Do not use cleaning discs or disc/lens cleaners (including wet or spray types). These may cause the player to malfunction.

On cleaning the video heads

• Rough picture

initial

contamination

When the video heads are dirty, clean the video heads using a Sony video head cleaning cassette. If a Sony cleaning cassette is not available in your area, have the heads cleaned at your nearest Sony dealer (a standard service fee will be charged). Do not use a commercially available liquid type cleaning cassette, as it may damage the video heads.

• Unclear picture

• No picture (or black & white screen appears)

terminal

On replacement of parts

In the event that this unit is repaired, repaired parts may be collected for reuse or recycling purposes.

continued

Precautions

• Television programs, films, video tapes and other materials may be copyrighted. Unauthorized recording of such material may be contrary to the provisions of the copyright laws. Also, use of this recorder with cable television transmission may require authorization from the cable television transmission and/or program owner.

• This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights. Use of this copyright protection technology must be authorized by Macrovision, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision. Reverse engineering or disassembly is prohibited.

IMPORTANT NOTICE

Caution: This player is capable of holding a still video image or on-screen display image on your television screen indefinitel y. If you leave the st ill video image or on-screen display image displayed on your TV for an extended period of time you risk permanent damage to your television screen. Projection televisions are especially susceptible to this.

Important Safety Instructions

1 Read these instructions. 2 Keep these instructions. 3 Heed all warnings. 4 Follow all instructions. 5 Do not use this apparatus near water. 6 Clean only with dry cloth. 7 Do not block any ventilation openings. Install in

accordance with the manufacturer’s instructions.

8 Do not install near any heat sources such as

radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9 Do not defeat the safety purpose of the

polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10 Protect the power cord from being walked on or

pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11 Only use attachments/accessories specified by

the manufacturer.

12 Use only with the cart, stand,

tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13 Unplug this apparatus during lightning storms

or when unused for long periods of time.

14 Refer all servicing to qualified service

personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

Precautions

Table of contents

2 WA R N I N G 2 Notes about discs 3 Precautions 7 About this manual 7 This player can play the following discs

Getting Started

10 Step 1 : Unpacking 11 Step 2 : Setting up the remote commander 14 Step 3 : Basic hookups 20 Step 4 : Selecting a language 21 Step 5 : Setting the clock 25 Step 6 : Presetting channels 29 Step 7 : Setting up the VCR Plus+

Advanced Hookups

32 S-Video/Component Video/HDMI hookup 34 A/V Receiver hookup

system

Basic Operations

36 Playing discs 40 Guide to the on-screen display 43 Playing a tape 47 Recording TV programs 50 Recording TV programs using the timer 53 Recording TV programs using the VCR Plus+ 56 Checking/changing/canceling timer settings 58 Locking the DVD-VCR (Child Lock)

system

continued

Table of contents

DVD Settings and Adjustments

59 Audio Setup 62 Screen Setup 66 Setting the display or sound track language 68 Parental Control (limiting playback by children)

DVD Additional Operations

71 Using the DVD’s menu 72 Zooming into a scene 73 Changing the angles 74 Displaying the subtitle 76 Various play mode functions (Program play, Shuffle play, Repeat play) 80 Changing the sound 82 Virtual surround setting 84 Playing an MP3 audio track 90 Playing JPEG image files 94 Playing VIDEO CDs with “PBC ON/OFF” Functions

VCR Additional Operations

96 Quick Timer Recording 97 Recording stereo and bilingual programs

98 Searching using various functions 100 Changing menu options 102 Editing with another VCR

Additional Information

104 General setup information 107 Troubleshooting 112 Glossary 114 Specifications 115 Index to parts and controls 119 DVD Audio/Subtitle Language 120 Index

* VCR Plus+ and PlusCode are registered trademarks of Gemstar Development Corporation.

The VCR Plus+ system is manufactured under license from Gemstar Development Corporation.

Table of contents

About this manual

This player can play the

• This manual mainly explains operations using the remote, but the same operations can also be performed using the buttons on the DVD-VCR having the same or similar names.

• “DVD” may be used as a general term for DVD VIDEOs, DVD-RWs/DVD-Rs, and DVD+RWs/ DVD+Rs.

• The meaning of the icons used in this manual is described below:

Icon Meaning

Functions available for DVD VIDEOs and DVD-RWs/DVDRs in video mode or DVD+RWs/ DVD+Rs

Functions available for DVDRWs/DVD-Rs in VR (Video Recording) mode

Functions available for VIDEO CDs, Super VCDs or CD-Rs/CDRWs in video CD format or Super VCD format

Functions available for music CDs or CD-Rs/CD-RWs in music CD format

Functions available for DATA CDs (CD-ROMs/CD-Rs/CDRWs containing MP3 tracks or JPEG files)

Functions available for DATA DVDs (DVD-ROMs/DVD+RWs/ DVD+Rs/DVD-RWs/DVD-Rs containing MP3 JPEG files)

Functions available for VHS VIDEOs

* MP3 (MPEG 1 Audio Layer 3) is a standard format

defined by ISO/MPEG which compresses audio data.

* audio

* audio tracks or

following discs

Format of discs

DVD VIDEO

DVD-RW/-R

DVD+RW/+R

VIDEO CD/ Music CD

CD-RW/-R

“DVD+RW,” “DVD-RW,” “DVD+R,” “DVD+R DL,” “DVD-R,” “DVD VIDEO,” and “CD” logos are trademarks.

Note about CDs/DVDs

The player can play CD-ROMs/CD-Rs/CD-RWs recorded in the following formats:

– music CD format – video CD format – MP3 audio tracks and JPEG image files of

format conforming to ISO 9660* Level 1/ Level 2, or its extended format, Joliet

– KODAK Picture CD format

* A logical format of files and folders on CD-ROMs,

defined by ISO (International Organization for Standardization).

The player can play DVD-ROMs/DVD+RWs/ DVD+Rs/DVD-RWs/DVD-Rs recorded in the following formats:

– MP3 audio tracks and JPEG image files of

format conforming to UDF (Universal Disk Format)

– 8 cm DVD+RW, DVD-RW, and DVD-R

recorded with a DVD Video camera

continued

About this manual

Region code

Your player has a region code printed on the back of the unit and only will play DVD VIDEO discs (playback only) lab eled with identical region codes. This system is used to protect copyrights.

DVDs labeled will also play on this player.

If you try to play any other DVD VIDEO, a message will appear on the TV screen to indicate that the disc is not playable. Depending on the DVD VIDEO, no region code indication may be labeled even though playing the DVD VIDEO is prohibited by area restrictions.

SLV-DXXXX

NO.

ALL

Region code

Example of discs that the player cannot play

The player cannot play the following discs:

• CD-ROMs/CD-Rs/CD-RWs other than those

recorded in the formats listed on the previous page.

• CD-ROMs recorded in PHOTO CD format.

• Data part of CD-Extras

• DVD Audios

• HD layer on Super Audio CDs

•DVD-RAMs

Also, the player cannot play the following discs:

• A DVD VIDEO with a different region code.

• A disc recorded in a color system other than

NTSC, such as PAL or SECAM (this player conforms to the NTSC color system).

• A disc that has a non-standard shape (e.g.,

card, heart).

• A disc with paper or stickers on it.

• A disc that has the adhesive of cellophane tape

or a sticker still left on it.

Notes about DVD+RWs/ DVD+Rs, DVD-RWs/DVD-Rs or CD-Rs/CD-RWs

Some DVD+RWs/DVD+Rs, DVD-RWs/DVDRs or CD-Rs/CD-RWs cannot be played on this player due to the recording quality or physical condition of the disc, or the characteristics of the recording device and authoring software. The disc will not play if it has not been correctly finalized. For more information, refer to the operating instructions for the recording device. Note that some playback functions may not work with some DVD+RWs/DVD+Rs, even if they have been correctly finalized. In this case, view the disc by normal playback. Also some DATA CDs/DATA DVDs created in Packet Write format cannot be played.

Note on playback operations of DVDs and VIDEO CDs

Some playback operations of DVDs and VIDEO CDs may be intentionally set by software producers. Since this player plays DVDs and VIDEO CDs according to the disc contents the software producers designed, some playback features may not be available. Also, refer to the instructions supplied with the DVDs or VIDEO CDs.

Music discs encoded with copyright protection technologies

This product is designed to playback discs that conform to the Compact Disc (CD) standard. Recently, various music discs encoded with copyright protection technologies are marketed by some record companies. Please be aware that among those discs, there are some that do not conform to the CD standard and may not be playable by this product.

This player can play the following discs

Note on DualDiscs

A DualDisc is a two sided disc product which mates DVD recorded material on one side with digital audio material on the other side. However, since the audio material side does not conform to the Compact Disc (CD) standard, playback on this product is not guaranteed.

This player can play the following discs

Getting Started

Step 1 : Unpacking

Check that you have received the following items with the DVD-VCR:

• Remote commander • 75-ohm coaxial cable with F-type

connectors

• Size AA (R6) batteries

Note

• The supplied remote commander is for the exclusive use of this DVD-VCR.

Unpacking

Step 2 : Setting up the remote commander

Inserting the batteries

Insert two size AA (R6) batteries by matching the + and – on the batteries to the diagram inside the battery compartment.

Insert the negative (–) end first, then push in and down until the positive (+) end clicks into position.

Reattach the cover after inserting the battery.

Using the remote commander

You can use this remote commander to operate this DVD-VCR and a Sony TV. Buttons on the remote commander marked with an orange dot (•) can be used to operate your Sony TV.

If the TV does not have the symbol near the remote sensor, this remote commander will not operate the TV.

Getting Started

Remote sensor

TV / DVD·VIDEO switch

SELECT VIDEO

SELECT DVD

To operate Set TV / DVD·VIDEO switch to

the DVD player DVD·VIDEO

the VCR DVD·VIDEO

your TV TV

DVD-VCR

and point at the remote sensor at your TV

, then press SELECT DVD and point at the remote sensor at the

, then press SELECT VIDEO and point at the remote sensor at the

continued

Setting up the remote commander

Notes

• With normal use, the batteries should last about three to six months.

• If you do not use the remote commander for an extended period of time, remove the batteries to avoid possible damage from battery leakage.

• Do not use a new battery with an old one.

• Do not use different types of batteries.

• Do not leave the remote commander in an extremely hot or humid place.

• Do not drop any foreign object into the remote casing, particularly when replacing the batteries.

• Do not expose the remote sensor to direct light from the sun or lighting apparatus. Doing so may cause a malfunction.

Controlling TVs with the remote commander

The remote commander is preprogrammed to control non-Sony TVs. If your TV is listed in the following table, set the appropriate manufacturer’s code number.

Set TV / DVD·VIDEO switch at the top of the remote commander to TV.

Hold down ?/1, and enter your TV’s code number using the number buttons. Then release

?/1.

Now you can use the buttons with an orange dot (•) to control your TV. When the TV/VIDEO

Buttons Operations

?/1 Turns your TV on or off

VOL +/– Adjusts the volume of your TV

CH +/– Selects the channel on your TV

Number buttons and ENTER* Selects the channel on a Sony TV

MUTING* Mutes a Sony TV equipped with the muting function

TV/VIDEO Switches your TV’s input source

*for Sony TV only

switch is set to TV, the remote performs the following:

Setting up the remote commander

Code numbers of controllable TVs

If more than one code number is listed, try entering them one at a time until you find the one that works with your TV.

TV brand Code number

Sony 01 (default)

Akai 04

AOC 04

Centurion 12

Coronado 03

Curtis-Mathes 12

Daewoo 22

Daytron 12

Emerson 03, 04, 14

Fisher 11

General Electric 06, 10

LG/Gold Star 03, 04, 17

Hitachi 02, 03

J.C.Penney 04, 12

JVC 09

KMC 03

Magnavox 03, 08, 12

Marantz 04, 13

MGA/Mitsubishi 04, 12, 13, 17

NEC 04, 12

TV brand Code number

Panasonic 06, 19

Philco 03, 04

Philips 08

Pioneer 16

Portland 03

Quasar 06, 18

Radio Shack 05, 14

RCA 04, 10

Sampo 12

Sanyo 11

Scott 12

Sears 07, 10, 11

Sharp 03, 05, 18

Sylvania 08, 12

Teknika 03, 08, 14

Tos h ib a 07

Wards 03, 04, 12

Yo rx 12

Zenith 15

Getting Started

Notes

• If you enter a new code number, the code number previously entered will be erased.

• If the TV uses a different remote control system from the one programmed to work with the DVD-VCR, you cannot control your TV with the remote commander.

• When you replace the batteries of the remote commander, the code number may change. Set the appropriate code number every time you replace the batteries.

Setting up the remote commander

Step 3 : Basic hookups

Before you get started

• Be sure to disconnect the AC power cord of each component before connecting.

• Turn off the power to all equipment.

• Do not connect the AC power cords until all of the connections are completed. If

you connect the AC power cord before the connections are completed, you may not be able to use the Plug and Play function.

• Be sure you make connections firmly. Loose connections may cause picture

distortion.

• If your TV does not match any of the examples provided, see your nearest Sony

dealer or qualified technician.

Selecting the best hookup option

There are many ways in which your DVD-VCR can be hooked up. To hook up your DVD-VCR so that it works best for you, first scan through the table below. Then use the accompanying diagrams and procedures on the following pages to set up your DVD-VCR.

If your TV has audio/video inputs, refer to page 15 for audio/video (A/V) hookup. Then follow one of the hookups below. If your TV does not have A/V inputs, go directly to one of the hookups below.

If you have Use Refer to

Antenna only, no cable TV Hookup 1 A or B

No cable box or cable box with only a few scrambled channels

Cable box with many scrambled channels Hookup 2 Page 19

(Plug and Play)

Hookup 1 C (Plug and Play)

Page 16 and 18

Page 17 and 18

After you have completed the connections, follow the instructions for setup.

After you have completed the setup, you are ready to use your DVD-VCR. Procedures differ depending on the hookup you used.

Caution

Connections between the DVD-VCR’s VHF/UHF connector and the antenna terminals of the TV receiver should be made only as shown in the following instructions. Failure to do so may result in operation that violates the regulations of the Federal Communications Commission regarding the use and operation of RF devices. Never connect the output of the DVD-VCR to an antenna or make simultaneous (parallel) antenna and DVD-VCR connections at the antenna terminals of your receiver.

Note to CATV system installer (in USA)

This reminder is provided to call the CATV system installer’s attention to Article 820- 40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.

Basic hookups

Audio/video (A/V) hookup

If your TV has audio/video (A/V) input jacks, you will get better picture and sound if you hook up your DVD-VCR using these connections. If your TV does not have A/V inputs, see the following pages for antenna or cable hookups. Note that “Advanced Hookups” (page 32) explains additional hookup methods that will optimize the picture and sound for a true “hometheater” experience.

If you are not planning to use your DVD-VCR to record programs, you only need to make the connections shown on this page. If you want to record regular or cable TV programs, complete these connections first, and then go to the following pages for antenna or cable hookups.

A Use this hookup if your TV has stereo jacks

Stereo receiverDVD-VCR

Audio/video cord (not supplied)

Audio cord (not supplied)

B Use this hookup if your TV does not have stereo jacks

Stereo receiverDVD-VCR

Getting Started

Video cord (not supplied)

Audio cord (not supplied)

Notes

• To play a tape/disc in stereo, you must use the A/V connection.

• If you do not have a stereo receiver, connect the white LINE OUT/AUDIO L jack to the AUDIO IN jack on your TV.

continued

Basic hookups

Hookup 1 (Plug and Play)

A Use this hookup if you are using:

• VHF/UHF antenna (you get channels 2–13 and channels 14 and higher)

• UHF-only antenna (you get channels 14 and higher)

• Separate VHF and UHF antennas

DVD-VCR

B Use this hookup if you are using a VHF-only antenna (you get

channels 2–13 only)

DVD-VCR

Rear of TV VHF/UHF

VHF

UHF

VHF

UHF

Rear of TV VHF/UHF

VHF

UHF

VHF

UHF

Match the type of connector on your TV: A, B, or C.

For connector types B and C, no UHF connection is required.

If you cannot connect your antenna cable to the DVD-VCR directly

If your antenna cable is a flat cable (300-ohm twin lead cable), attach an external antenna connector (not supplied) so you can connect the cable to the IN connector. If you have separate cables for VHF and UHF antennas, you should use a U/V band mixer (not supplied) (page 106).

Basic hookups

C Use this hookup if you have no cable box, or a cable box with only a

few scrambled channels

What you can do with this hookup

• Record any unscrambled channel by selecting the channel on the VCR

What you cannot do

• Record scrambled channels that require a cable box

Getting Started

Wall

Connect this cable directly to your TV if you do not have a cable box.

DVD-VCR

Cable box

Rear of TV VHF/UHF

VHF

UHF

VHF

UHF

Match the type of connector on your TV: A, B, or C.

For connector types B and C, no UHF connection is required.

continued

Basic hookups

DVD-VCR setup (Hookup 1 continued)

Plug the DVD-VCR into an AC outlet.

The DVD-VCR automatically presets the DVD-VCR’s clock and TV channels when the DVD-VCR is plugged into the AC outlet.

to AC outlet

AC power cord

The DVD-VCR starts presetting the clock and channels.

When Auto preset is completed, the current time appears in the display window.

You have now completed DVD-VCR setup. To begin using your DVD-VCR, go to “Basic Operations” on page 36.

To change the on-screen display language to French or Spanish, see “Step 4 : Selecting a language” on page 20.

The clock is set using a time signal provided by some TV channels. If the clock is incorrect, or “–:–” appears in the display window, see “Using Manual Clock Set” on page 23.

To add or disable channels manually, see “Presetting/disabling channels manually” on page 27.

Notes

• If you connect the AC power cord before the antenna connections are completed, the channels

may be incorrectly set. If this happens, see “Step 6 : Presetting channels” on page 25.

• Do not press any buttons on the DVD-VCR or remote commander during Auto preset.

• Auto preset starts automatically only when you plug in the AC power cord for the first time

after you purchase the DVD-VCR.

• Auto preset can be performed by pressing x on the unit

with the DVD-VCR power turned off.

continuously for 5 seconds or more

Basic hookups

Hookup 2

Use this hookup if you are connecting a cable box with many scrambled channels

What you can do with this hookup

• Record any channel by selecting the channel on the cable box

What you cannot do

• Record with the cable box turned off

• Record one channel while watching another channel

Getting Started

Wall

Cable box

DVD-VCR

Rear of TV VHF/UHF

VHF

UHF

VHF

UHF

Match the type of connector on your TV: A, B, or C.

For connector types B and C, no UHF connection is required.

After you have completed hookup…

After you have completed hookup, plug the DVD-VCR into an AC outlet and see “Step 4 : Selecting a language” on page 20.

to AC outlet

AC power cord

Basic hookups

Step 4 : Selecting a language

You can change the on-screen display language.

Before you start…

• Turn on the DVD-VCR and your TV.

• Set the TV to video input so that the signal from the player appears on the TV screen.

•Set TV

• If the DVD player is in play mode, you

/ DVD·VIDEO switch to

DVD·VIDEO on the remote.

cannot display the setup menu. Stop the DVD playback.

SET UP

V/v

ENTER

Selecting a language

Press SET UP, then press V/v to select (OPTION) and press ENTER.

Press V/v to select “Language”, then press ENTER.

The “LANGUAGE/IDIOMA/LANGUE” menu appears.

Press V/v to select the desired language, English, Spanish or French, then press ENTER.

Press SET UP to exit the menu.

Step 5 : Setting the clock

You must set the clock on the DVD-VCR to use the timer features properly.

Using the Auto Clock Set feature

Some TV and cable channels transmit time signals with their broadcasts. Your DVDVCR can pick up this time signal to automatically set the clock.

The Auto Clock Set feature works only if a channel in your area is broadcasting a time signal. If broadcasters in your area are not sending time signals, set the time manually (page 23).

Before you start…

• Turn on the DVD-VCR and your TV. When using a cable box, turn it on.

• Set the TV to video input so that the signal from the player appears on the TV screen.

•Set TV

• If the DVD player is in play mode, you

/ DVD·VIDEO switch to

DVD·VIDEO

cannot display the setup menu. Stop the DVD playback.

on the remote.

Press SET UP, then press V/v to select (OPTION) and press ENTER.

Getting Started

SET UP

V/v/B/b

ENTER

O RETURN

Press V/v to select “Clock Set/Adjust”, then press ENTER.

The “CLOCK SET/ADJUST” menu appears.

continued

Setting the clock

Press V/v to select “Auto”, then press ENTER.

Press V/v to select the item you want, then press B/b to make the setting.

• For “Clock data CH” Leave the setting to “Auto” to have the DVD-VCR automatically search for a channel that carries a time signal. Press to select a channel that carries a time signal. Use this option if you know of a channel that carries a time signal. Most PBS member stations broadcast a time signal. For the fastest response, select your local PBS station.

• For “Time zone” Select the time zone of your area, or select “Auto” to have the DVD-VCR automatically set your time zone. The options are: Auto y Atl. (Atlantic) y East (Eastern) y Cen. (Central) y Mtn. (Mountain) y Pac. (Pacific) y Alas (Alaska) y Haw. (Hawaii) y Auto

• For “Daylight saving” Select “Yes” or “No” (standard time), or “Auto” to have the DVD-VCR automatically set the daylight saving time.

B/b

Press O RETURN, then press SET UP to exit the menu.

To activate the Auto Clock Set function, turn off the DVD-VCR.

Setting the clock

Notes

• The clock cannot be set automatically if you do not receive a channel that carries a time signal in your area. If so, set the clock manually (page 23).

• If there are only a few channels in your area that carry time signals, setting the clock automatically may take up to about 20 minutes. If nothing happens even after you wait about 20 minutes, set the clock manually (page 23).

• If you made Hookup 2, make sure you leave the cable box on.

• The clock display appears when VIDEO mode is selected with no tape inserted or when the DVD-VCR is turned off.

Using Manual Clock Set

Before you start…

• Turn on the DVD-VCR and your TV.

• Set the TV to video input so that the signal from the player appears on the TV screen.

•Set TV

• If the DVD player is in play mode, you

/ DVD·VIDEO switch to

DVD·VIDEO on the remote.

cannot display the setup menu. Stop the DVD playback.

Getting Started

SET UP

V/v/B/b

ENTER

Press SET UP, then press V/v to select (OPTION) and press ENTER.

Press V/v to select “Clock Set/Adjust”, then press ENTER.

The “CLOCK SET/ADJUST” menu appears.

continued

Setting the clock

Press V/v to select “Manual”, then press ENTER.

Set the hour, minutes, month, day and year in sequence by pressing B/b to select the item to be set, and press V/v to select the digits. The day of the week is set automatically.

Press ENTER to confirm the setting.

Press SET UP to exit the menu.

Note

• The clock display appears when VIDEO mode is selected with no tape inserted or when the DVD-VCR is turned off.

Setting the clock

Step 6 : Presetting channels

This DVD-VCR is capable of receiving VHF channels 2 to 13, UHF channels 14 to 69 and unscrambled CATV channels 1 to 125. First, we recommend that you preset the receivable channels in your area using automatic presetting methods. Then, if there are any unwanted channels, disable them manually. If you have already decided which channels you wish to preset, set them directly using manual presetting methods (page 27).

Presetting all receivable channels automatically

Before you start…

• Turn on the DVD-VCR and your TV. When using a cable box, turn it on.

• Set the TV to video input so that the signal from the player appears on the TV screen.

•Set TV

• If the DVD player is in play mode, you

/ DVD·VIDEO switch to

DVD·VIDEO on the remote.

cannot display the setup menu. Stop the DVD playback.

SET UP

V/v/B/b

ENTER

Getting Started

Press SET UP, then press V/v to select (OPTION) and press ENTER.

continued

Presetting channels

Press V/v to select “Channel Setup”, then press ENTER.

The “CHANNEL SETUP” menu appears.

Press V/v to select “Ant/Cable.”

• To preset cable TV channels: Press

B/b to select “Cable TV.”

• To preset VHF and UHF channels:

B/b to select “Antenna.”

Press

Press V/v to select “Auto Channel Memory,” then press ENTER.

All receivable channels are preset in numerical sequence. When no more receivable channels can be found, presetting stops and the picture from the lowest numbered channel is displayed on the TV screen.

Presetting channels

Presetting/disabling channels manually

Before you start…

• Turn on the DVD-VCR and your TV. When using a cable box, turn it on.

• Set the TV to video input so that the signal from the player appears on the TV screen.

•Set TV

• If the DVD player is in play mode, you

/ DVD·VIDEO switch to

DVD·VIDEO on the remote.

cannot display the setup menu. Stop the DVD playback.

Getting Started

CH +/– Number

buttons

SET UP

V/v/B/b

ENTER

O RETURN

Press SET UP, then press V/v to select (OPTION) and press ENTER.

Press V/v to select “Channel Setup”, then press ENTER.

The “CHANNEL SETUP” menu appears.

continued

Presetting channels

Press V/v to select “Channel Add/Delete,” then press ENTER.

To preset/disable a channel:

1 Press CH +/– or number buttons to enter

the channel number.

2 Press B/b to select “ADD” (in memory)

or “DELETE” (deleted).

3 Press ENTER.

Press O RETURN to confirm the setting.

Press SET UP to exit the menu.

Channel to be preset

Channel to be disabled

Presetting channels

Note

• If you have not preset channels automatically, you cannot preset/disable channels manually.

Step 7 : Setting up the VCR Plus+® system

SAMPLE

How the VCR Plus+ system works

Whenever you want to record a TV program, all you need to do is look up the “PlusCode” number, a number assigned to each program published in the TV section of most newspapers, cable TV listings, and even TV GUIDE magazine. Then, just enter the PlusCode number of the program you want and the VCR is automatically programmed to record that show. It’s that simple.

Example of “PlusCode”

MOVIE Musical (2hrs.)

5:30

SPORT

CNN

6:30

SCIENCE AND TECHNOLOGY

(1hr. 15min.) 73457

Golf (1hr. 25min.) 42060

WS 9974

DRAMA

Comedy (2hrs.) 17390

PlusCode

33044

Getting Started

How to set up your VCR

Setting up your VCR involves coordinating the TV channel number (the number you turn to on your TV or VCR to watch a program) with the guide channel (the number that is assigned to that channel in your program guide).

To find the guide channel numbers, look at the “Channel Line-up Chart” in the program guide for your area that features VCR PlusCode numbers. It usually looks like the example to the right.

To set the guide channels, use the Channel Line-up Chart to check that the guide channel numbers match the TV channel your VCR receives. For example, if HBO is listed in the Channel Line-up Chart as channel 33, and your VCR receives HBO on channel 5, you need to coordinate these numbers using the following procedure. If the guide and TV channel numbers are the same, you can skip this procedure.

Example of “Channel Line-up Chart”

CABLE CH

16 17 20 21 22 25 34 35

27 29 30 31 38 39 45 17 44 49 50 51

CABLE TV

AMC

American Movie Classics

BRV

Bravo (program grid only)

CNN

Cable News Network

CSP

C-SPAN The Disney Channel

DIS

DSC

The Discovery Channel

ESN

ESPN

FAM

The Family Channel Home Box Office

HBO

LIF

Lifetime

MAX

Cinemax

MTV

Music Television Nickelodeon

NIK

Sports Channel

SCA

Sports Channel America

SHO

Showtime

TBS

TBS SuperStation

TMC

The Movie Channel

TNN

The Nashville Network

TNT

Turner Network Television

USA

USA Network

VCR Plus+ GUIDE CH

35 54 42 28 53 37 34 47 33 46 45 48 38 59 70 41 43 58 49 52 44

continued

Setting up the VCR Plus+® system

SET UP

V/v/B/b

ENTER

O RETURN

Press SET UP, then press V/v to select (OPTION) and press ENTER.

Press V/v to select “Channel Setup”, then press ENTER.

The “CHANNEL SETUP” menu appears.

Press V/v to select “Guide Channel Setup,” then press ENTER.

Language Clock Set/Adjust Channel Setup Auto Power Off RF Output Channel

ENTER

GUIDE CHANNEL SETUP

[GUIDE CH]

[TV CH] Enter actual

receiving channel

vVb

OPTION SETUP

:English

[ Off ] [3CH ]

SET UP

RETURN

SET UP

RETURN

Setting up the VCR Plus+® system

+ 108 hidden pages