Samsung SIP005AFS30 User Manual

DB2/ 30119155.1
DRAFT 04/12/16 5:16PM 4:05PM

MODULE DISCLOSURES – QUICK START GUIDE

FCC REGULATORY DISCLOSURES

This device complies with Part 15 of the FCC`s Rules. Operation is subject to the following two
Conditions: (1) This device may not cause harmful interference, and (2) This device must accept any
interference received, including interference that may cause undesirable operation

This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:

 Reorient or relocate the receiving antenna.
 Increase the separation between the equipment and receiver.
 Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

 Consult the dealer or an experienced radio/ TV technician for help.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with a minimum distance of 20cm between the
transmitter’s radiating structure(s) and the body of the user or nearby persons.

This module is intended for OEM integration. The OEM integrator is responsible for FCC compliance and
compliance with all applicable regulations including those for modular transmitters 47 C.F.R. 15.212.
The OEM product must comply with all applicable labeling requirements including those contained in 15
C.F.R. 15.19. The OEM is solely responsible for certification and testing and labeling of its own products.
In addition to any independently required labels, the OEM shall also affix to the outside of a device into
which the module is installed a label referring to the enclosed module. This exterior label should be

prepared in a legible font and permanently affixed and using the wording “Contains Transmitter Module

FCCID: A3LSIP005AFS30

The OEM is required to ensure that the end product integrates this module so as to maintain a minimum

distance of 20 cm between the equipment’s radiating structure(s) and the body of the user or nearby

persons. The OEM shall also advise its end user of this requirement as required by applicable rules.

The OEM shall require that the end user of its product be informed that the FCC radio frequency
exposure guidelines for an uncontrolled environment can be satisfied. The OEM shall further inform its

DB2/ 30119155.1
DRAFT 04/12/16 5:16PM 4:05PM

end user that any change or modifications to this module not expressly approved by the manufacturer
will void the warranty and the users’ authority to operate the equipment.

INDUSTRY CANADA REGULATORY DISCLOSURES

INDUSTRY CANADA STATEMENT

This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.

Cet appareil est conforme avec Industrie Canada exempts de licence standard RSS (s). L'opération est
soumise aux deux conditions suivantes:(1) cet appareil ne peut causer d'interférences, et
(2) cet appareil doit accepter toute interférence, y compris les interférences qui peuvent causer un
mauvais fonctionnement de l'appareil.

INDUSTRY CANADA RADIATION EXPOSURE STATEMENT AND LIMITATIONS ON USE

This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20 cm between
the radiator and your body. This equipment should be installed and must not be co-located or operating
in conjunction with any other antenna or transmitter.

This equipment is restricted to indoor use in the 5.15-5.25 GHz range. This equipment is not able to be
operated at 5600-5650. In the United States and Canada, only Channel 1~11 can be operated and these
channel assignments deal only with the 2.4 GHz range.

The end product must be labeled to display the Industry Canada certification number of the module.

“Contains transmitter module IC: 649E-SIP005AFS30”

Le dispositif d'accueil doivent être étiquetés pour afficher le numéro de certification d'Industrie Canada
du module.

Contient module émetteur IC : 649E-SIP005AFS30