Samsung SHD-B-3100FP1 User Manual
Backbox
Camera Bracket
Bracket Feet (2
sizes included
Backbox
Mount Feet
(6 included)
Trim Ring
3 x #10-32 x 3/8”
Socket Head Cap Screws
(see Note below)
4 x M3 x 6mm Phillips
Head Screws and M3
Flat Washers
Camera Bracket
3 x Slotted toggle bolts
3 x #6-32 Oval Head
Slotted Screws
Made in the USA by Broadsight
Systems, Inc. for Samsung Techwin
4 x Holes for M4
Screws and Nuts
(see Note below)
2 x Holes for #6-32 x 5/16
Phillips Head Screws (see
Note below)
Group 1 - Shortest Screws: SCV-2080, SCV-3080, SNV-3082,
SNV-3120, SNV-5080, SNV-5080R, SNV-7082, SNV-7080R
Group 2 – Middle Screws: SCV-6081R, SNV-5084, SNV-5084R,
SNV-6084, SNV-6084R, SNV-7084, SNV-7084R
Group 3 – Tallest Screws: SND-5084, SND-5084R, SND-6084,
SND-6084R, SND-7084, SND-7084R
Compatible Model List
INSTALLATION MANUAL – SHD-B-3100FP1 Recessed Plenum Backbox for
Samsung Indoor and Outdoor Dome Cameras
Unpacking
Unpack carefully. This is mechanical equipment and should be
handled with care. If an item appears to have been damaged in
shipment, replace it properly in its carton and notify the shipper. If
any items are missing, notify Broadsight Systems, Inc. The
shipping carton is the safest container in which the unit may be
transported. Save it for possible future use.
Service
If the unit ever needs repair service, the customer should contact
Broadsight Systems, Inc. for a return materials authorization (RMA)
and shipping instructions.
Care and Maintenance
Perform routine maintenance to keep the unit dust free.
Model Designation
SHD-B-3100FP Recessed Plenum Backbox Mount for
Samsung Indoor and Outdoor Dome Cameras
Description
The Backbox is inserted to a hole cut into a ceiling tile and
secured with toggle bolts. The camera attaches to a separate
bracket. The camera/bracket assembly then attach to the
Backbox before the trim ring is installed.
Hardware Kit
1 x Camera bracket
6 x Mount feet (three sets of two feet, see Note)
4 x M3 x 6mm Pan head Phillips screws
4 x M3 Flat washers
4 x M4 Pan Head Phillips screws
4 x M4 hex nuts
3 x #10-32 x 3/8” Socket head cap screws
2 x #6-32 Pan head Phillips screws
3 x #6-32 Oval head slotted screws
Tools Required
5/32” Hex Wrench
Flat blade screwdriver
#1 Phillips head screwdriver
Certification
Camera installation should be performed by a licensed professional
and conform to the National Electrical Code (NEC) and any
applicable local codes.
Installation
1. Hold the included template up to the ceiling tile and mark the
area to be cut away, or mark a 7.5-inch diameter circle. Cut
out the shape in the ceiling tile as needed.
2. Carefully insert the backbox into the hole in the ceiling tile.
Compress the toggle bolts when inserting them into the tile.
3. Tighten the toggle bolts until the flange of the backbox is flush
with the bottom of the ceiling tile.
4. If required, attach a support wire (not included) to the 3/16”
hole in the hanger bracket on the top of the backbox.
5. Knockouts are provided that accept ½” conduit fittings.
Detach knockout(s) as needed to allow cable entry into the
unit.
Figure 1 - Backbox Exploded View
6. Attach camera to camera bracket using the hardware
referenced in the Note below. Attach the appropriate Mount
Feet to the Camera Bracket as shown in Figure 1 using four (4)
M3x6mm screws and M3 flat washers.
Note: Three (3) sets of Mount Feet and three (3) sets of camera
fasteners are included:
If installing the
tall) mount feet and attach the camera using the four (4) M4 Pan Head
Phillips screws and M4 nuts.
If installing the
feet and attach the camera using the three (3) #10-32 x 3/8” Socket Head
Cap Screws.
If installing the
feet and attach the camera using the two (2) #6-32 Pan head Phillips
screws.
7. Locate screws in the base of the backbox that the mount feet
will attach to. Align the screw heads with the slots and rotate
the camera slightly clockwise to secure.
8. Install trim ring using 3 x #6-32 screws.
SNV-7082 (Group 1)
SNV-5084 (Group 2)
SND-5084 (Group 3)
camera, use the
, use the
, use the
MIDDLE
TALLEST
SHORTEST
(1.5” tall) mount
(2” tall) mount
Page 1 of 1
(3/4”
Loading...