7 Pingchang Rd, Nankai Dist, Tianjin, P.R China
Post Code : 300190
TEL: 86-22-2761-9698 FAX: 86-22-2761-6514
P/No. : Z6806-0541-01A
VAN 04. 12
SAMSUNG CCD CAMERA
The lightning flash with an arrowhead symbol, within an equilateral triangle is
intended to alert the user to the presence of uninsulated “dangerous voltage”
within the product's enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user
to the presence of important operating and maintenance (servicing)
instructions in the literature accompanying the appliance.
INFORMATION-This equipment has been tested and found to comply with
limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instruction manual, may
cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference
at his own expense.
WARNING -Changes or modifications not expressly approved by the
manufacturer could void the user’s authority to operate the equipment.
CAUTION : To prevent electric shock and risk of fire hazards:
Do NOT use power sources other than that specified.
Do NOT expose this appliance to rain or moisture.
This installation should be made by a qualified service person and
should conform to all local codes.
FeaturesWarning
Fine Picture in Ultra Low
illumination.
SV-III built-in DSP and 1/3 high density
CCD allows bright and high quality
images to be captured in ultra low light
condition.
- 0.13Lux at Color
- 0.001Lux at Sens-Up mode
Wide Dynamic Range(WDR)
SV-III DSP has Strong compensation
performance in WDR.
So It always shows obvious, clear and perfect
light contrast picture in any environment.
SSNR(Samsung Super Noise
Reduction)
SHC-730 has powerful DSP that can
remove image noise efficiently and it
shows clean and obvious image in low
luminance.
High Resolution
The horizontal resolution of 520TV lines
at Color mode and 570TV lines at BW
mode can be achieved by using a high
density CCD having Double Speed
410,000 pixels SONY CCD, which provides
clean, noiseless and reliable pictures.
Day & Night
The camera provides automatic mode
change over by sensing day or night
conditions. It can change color mode in
the day condition for optimal color and
BW mode in night condition for clear
identification.
Motion Detection
The camera transmits an alert signal to
the MD Output Terminal when it detects
motion of an object. If you connect an
optional alarm to the camera, you can
get the effective surveillance.
VIDEO/DC Lens Selectable
The camera accepts 2 types of auto iris
lenses (DC type/VIDEO type) and is set
with the VIDEO/DC selection switch.
You can control the camera using OSD
menu and RS-232C jack at a remote
place.
The camera needs periodic inspection.
Contact an authorized technician for inspection.
Stop using your camera when you find a malfunction.
If you use your camera around smoke or unusual heat for a long time, a
fire may be caused.
Do not Install the camera on a surface that can not support it.
Unless the surface is suitable, it could cause falling or other hazards.
Do not hold plug with wet hands.
It could cause an electric shock.
Do not disassemble the camera.
It may result in fire, electric shock or other hazards.
Do not use the camera close to a gas or oil leak.
It may result in fire or other hazards.
COLOR CCD CAMERACOLOR CCD CAMERAUser’s ManualUser’s Manual
54
Contents
Precautions
Composition
Name and Function of Each Part
Front
Side
Bottom
Back
Connection
Lens
• Installing Auto Iris Lens
• Installing C/CS-Mount Lens
Connecting to Monitor
Connecting to Power
821
10
11
11
12
13
14
15
15
Operating Your Camera
Configuration of The Menu
Setting Up The Menu
• CAMERA ID
• BACKLIGHT
• WHITE BALANCE
• MOTION DETECTION
• LENS SELECTION
• SHUTTER SPEED CONTROL
• AGC
• SENSE UP
• SSNR
• SPECIAL
Using Reomte Jack / MD Output / D&N Input
19
20
Troubleshooting
Specifications
21
22
23
26
27
28
30
32
34
35
36
37
40
42
44
COLOR CCD CAMERACOLOR CCD CAMERAUser’s ManualUser’s Manual
76
Precautions
Do not install the camera in
extreme temperature conditions.
Only use the camera under conditions
where temperatures are between -10˚C
and +50˚C. Be especially careful to provide
ventilation when operating under high
temperatures.
Do not install the camera under
unstable lighting conditions.
Severe lighting change or flicker can
cause the camera to work improperly.
Do not install or use the camera in an
environment where the humidity is high.
It can cause the image quality to be poor.
Do not touch the front lens of the
camera.
It is one of the most important parts of
the camera. Be careful not to be stained
by fingerprint.
Do not drop the camera or subject
them to physical shocks.
It can cause malfunctions to occur.
Do not expose the camera to rain
or spill beverage on it.
If it gets wet, wipe it dry immediately.
Liquids can contain minerals that corrode
the electronic components.
Notes
• If the camera is exposed to spotlight or object reflecting strong light, smear or
blooming may occur.
• Please check that the power satisfies the normal specification before connecting
the camera.
Never keep the camera face to
strong light directly.
It can damage the CCD.
Do not expose the camera to
radioactivity.
If it is exposed to radioactivity,
For heated CCD, it will be out of order.
COLOR CCD CAMERACOLOR CCD CAMERAUser’s ManualUser’s Manual
98
Composition
Name and Function of Each Section
Front
1. High Sensitivity Color Camera
2. Auto Iris Lens Plug
3. Remote Plug
4. C-Mount Adapter
5. Instruction Manual
C-Mount Lens Adapter
Used to attach C-mount lens.
Tripod Mounting Bracket
Screw Hole
Used to fix the Tripod mounting
bracket on the top of the camera.
Back Focus Adjustment Lever
Used to adjust back focal length
COLOR CCD CAMERACOLOR CCD CAMERAUser’s ManualUser’s Manual
1110
Name and Function of Each Section
L
Side
BACK FOCUS ADJUSTMENT LEVER
When you don’t obtain focused point after adjusting lens focus,
adjust the lever.
Auto Iris Lens Connector
Used to connect Auto Iris Lens plug.
DC/VIDEO Selection Switch
Used to choose DC or VIDEO according to the
type of your Auto Iris Lens.
Menu Setup Buttons Cover
Menu Setup Buttons
• SET Button: Used to access menu mode. Also used to confirm the setting.
• UP/DOWN Button: Used to choose the desired menu item. It also moves
• LEFT/RIGHT Button:
the cursor up or down in the menu screen.
Used to change the parameter of the selected menu item.
It also moves the cursor the left or right in the menu screen.
Bottom
Tripod Mounting Hole
Used to install the camera on an optional
tripod. The tripod must be equipped with
the screw specified as shown below.
1/4"-20 UNC (20 THREAD)
L:4.5mm±0.2mm (ISO standard),
or 0.197" (ASA standard)
Tripod Mounting Bracket
You can remove and install this bracket on the top of the
camera. You must use the supplied screw or the
equivalent (within 4mm). If not, the bracket may not be
fixed properly.
COLOR CCD CAMERACOLOR CCD CAMERAUser’s ManualUser’s Manual
1312
ConnectionName and Function of Each Section
Back
Video Output Jack
Used to connect an external
video monitor in jack.
D&N
Used to input Day & Night
Control Signal
MD Output Terminal
Used to output motion detection signal.
Frame Ground
Used to connect an AC 24V or DC 12V power source.
Power LED
The LED turns on
when power is supplied.
Remote Jack
Used to connect a remoteplug.
AC / DC Power Terminal
LENS
The lens is not supplied with this camera. Purchase a lens suitable for your
environment. This camera accepts the auto iris lens and both C-and
CS-mount lens.
Notes
If the lens is marked with fingerprints or other marks, the image quality might be poor.
It is recommended to use a high quality lens to improve the image quality under
low illumination.
For using main functions it is recommended to use Auto Iris Lens with DC type.
Installing Auto Iris Lens
1. Peel approximately 8mm from the end of the lens cable outer cover.
approx. 8mm
2. Peel approximately 2mm from the end of the cable inner cover.
approx. 2mm
COLOR CCD CAMERACOLOR CCD CAMERAUser’s ManualUser’s Manual
1514
Loading...
+ 16 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.