This Service Manual is a property of Samsung Electronics Co.,Ltd.
Any unauthorized use of Manual can be punished under applicable
International and/or domestic law.
ⓒ
Samsung Electronics Co.,Ltd.
2007. 10. Rev.1.0
1. Safety Precautions
1-1. Repair Precaution
●
Repair in Shield Box, during detailed tuning.
Take specially care of tuning or test, because the specification of cellular phone is sensitive for
surrounding interference(RF noise).
●
Be careful to use a kind of magnetic object or tool, because performance of parts is damaged by the
influence of magnetic force.
●
Surely use a standard screwdriver when you disassemble this product, otherwise screw will be worn
away.
●
Use a thicken twisted wire when you measure level.
A thicken twisted wire has low resistance, therefore error of measurement is few.
●
Repair after separate Test Pack and Set because for short danger (for example an
overcurrent and furious flames of parts etc) when you repair board in condition of
connecting Test Pack and tuning on.
●
Take specially care of soldering, because Land of PCB is small and weak in heat.
●
Surely tune on/off while using AC power plug, because a repair of battery charger is
dangerous when tuning ON/OFF PBA and Connector after disassembling charger.
●
Don't use as you pleases after change other material than replacement registered on SEC System.
Otherwise engineer in charge isn't charged with problem that you don't keep this rules.
1-1
SAMSUNG Proprietary-Contents may change without notice
This Document can not be used without Samsung's authorization
Several semiconductor may be damaged easily by static electricity. Such parts are called by ESD
(Electrostatically Sensitive Devices), for example IC,BGA chip etc. Read Precaution below.
You can prevent from ESD damage by static electricity.
●
Remove static electricity remained your body before you touch semiconductor or parts with
semiconductor. There are ways that you touch an earthed place or wear static electricity
prevention string on wrist.
●
Use earthed soldering steel when you connect or disconnect ESD.
●
Use soldering removing tool to break static electricity. , otherwise ESD will be damaged by
static electricity.
●
Don't unpack until you set up ESD on product. Because most of ESD are packed by box and
aluminum
plate to have conductive power,they are prevented from static electricity.
●
You must maintain electric contact between ESD and place due to be set up until ESD is connected
completely to the proper place or a circuit board.
1-2
SAMSUNG Proprietary-Contents may change without notice
This Document can not be used without Samsung's authorization
2. Specification
2-1. GSM General Specification
EGSM 900DCS 1800PCS 1900WCDMA 2100
Freq. Band[MHz]
Uplink/Downlink
ARFCN range
Tx/Rx spacing10MHz20MHz20MHz130MHz
Mod. Bit rate/
Bit Period
Time Slot Period/
Frame Period
Modulation0.3GMSK0.3GMSK0.3GMSK
880~915
925~960
0~124 &
975~1023
270.833kbps
3.692us
576.9us
4.615ms
1710~1785
1805~1880
512~885512~810
270.833kbps
3.692us
576.9us
4.615ms
1850~1910
1930~1990
270.833kbps
3.692us
576.9us
4.615ms
1920~1980
2110~2170
UL:9612~9888
DL:10562~10838
3.84Mcps
(chip rate)
Frame length : 10ms
Slot length : 0.667ms
QPSK
HPSK
MS Power33dBm~5dBm30dBm~0dBm30dBm~0dBm24dBm~-50dBm
Power Class
Sensitivity-102dBm-100dBm-100dBm-106.7dBm
TDMAMux888
Cell Radius35Km2Km2Km2Km
4
(max +33dBm)
SAMSUNG Proprietary-Contents may change without notice
This Document can not be used without Samsung's authorization
1
(max +30dBm)
2-1
1
(max +30dBm)
3
(max +24dBm)
Specification
2-2. GSM TX power class
TX Power
control level
533±2dBm
631±2dBm
729±2dBm
827±2dBm
925±2dBm
1023±2 dBm
1121±2 dBm
GSM850
GSM900
TX Power
control level
030±3dBm
128±3dBm
226±3dBm
324±3dBm
422±3dBm
520±3dBm
618±3dBm
DCS1800
TX Power
control level
030±3dBm
128±3dBm
226±3dBm
324±3dBm
422±3dBm
520±3dBm
618±3dBm
PCS1900
1219±2 dBm
1317±2 dBm
1415±2 dBm
1513±2 dBm
1611±3 dBm
179±3 dBm
187±3 dBm
195±3 dBm
716±3dBm
814±3dBm
912±4dBm
1010±4 dBm
118±4 dBm
126±4 dBm
134±4 dBm
142±5 dBm
716±3dBm
814±3dBm
912±4dBm
1010±4 dBm
118±4 dBm
126±4 dBm
134±4 dBm
142±5 dBm
150±5 dBm
2-2
150±5 dBm
SAMSUNG Proprietary-Contents may change without notice
This Document can not be used without Samsung's authorization
3. Product Function
Main Function
HSDPA/UMTS, EDGE, GPRS
Touch wheel interface for Music UI
Bluetooth v2.0 + EDR
USB v2.0 HS compatible
Camera 2Mega x 16 Digital Zooming and camcorder
FMRadio
Instant Messaging capability
E-mail
Featured applications provide alarms, calendar, calculator, record audio, converter, timer, stopwatch,
and world time.
File viewer (MS office, PDF)
Multimedia Message Service (MMS)
Multimedia capability (with included Media player)
PhotocallerID
Speakerphone capability
WEB/WAP browser (HTMS, xHTML, WML)
3-1
SAMSUNG Proprietary-Contents may change without notice
This Document can not be used without Samsung's authorization
Product Function
3-2
SAMSUNG Proprietary-Contents may change without notice
This Document can not be used without Samsung's authorization
4. Array course control
4-1. Software Adjustments
- There is 2 set to download the binary image into your device.
[First set]
1. JIG BOX (UMTS TEST JIG; GH80-03308A)
2. USB Cable : JIG to PC
3. Test Cable : JIG to Impulse(GH39-00890A)
4. Power Cable : JIG to power supply
5. Serial Cable : JIG to PC
6. Power Supply
7. Rf Cable : Impulse to Agilent 8960 or CMU200(GH39-00397A)
4-1
SAMSUNG Proprietary-Contents may change without notice
This Document can not be used without Samsung's authorization
Array course control
[Second Set]
USB Data Link Cable : Impulse to PC (GH39-00922A)
Standard Battery for Impulse (GH43-02985A)
4-2
SAMSUNG Proprietary-Contents may change without notice
This Document can not be used without Samsung's authorization
4-2. Software Download
4-2-1. Pre-requisite for Download
SGH - i450 Mobile Device
Apollo v4.01.exe : Downloader Application for SGH-i450
USB Download Driver : SS60_Downloader_Driver.zip
Rom Image : PDA(*.IMG), MODEM(*.BIN) images
Equipment set for Download.
Array course control
4-3
SAMSUNG Proprietary-Contents may change without notice
This Document can not be used without Samsung's authorization
Array course control
4-2-2. Concupts & cautions.
You can download PDA or MODEM separately. But We are always recommended to
download both at the same time using same version of rom image.
To download an image, the phone need to be set to a proper download mode.
There are 3 download modes.
PDA download : Hold 1, 4 keys and power on -> Blue screen with some information.
MODEM download : Hold 7, * keys and power on -> Blinking "MODEM DOWNLOAD"
on blue screen
All download : Hold 4, 7 keys and power on -> Blinking "ALL DOWNLOAD" on blue screen
For PDA image download, the phone shows download progress on the screen
For MODEM image download, the phone shows RGBW/B Screen.
For All download mode, MODEM image is downloaded first and then PDA
downloading starts.
After downloading PDA, the phone will be reboot.
Do NOT interrupt downloading process or the phone will be damaged. You would be
unable to boot up the phone or to re-flash the phone. Let it finish downloading
process even though you are flashing wrong images.
4-4
SAMSUNG Proprietary-Contents may change without notice
This Document can not be used without Samsung's authorization
Array course control
4-2-3. USB Driver installation for PDA
Execution Apollo.exe.
SGH-i450 connect to the Host computer using download equipment set.
Hold “1+4” key and insert power supplied test cable when use equipment set 1
or Hold “1+4” key and press power on key when use equipment set 2.
Install PDA side driver.
Follow New H/W Installation Manager.
Select ‘IBootHostUSB.inf’file under ‘i450_Apollo_Drivers\PDA_driver’ folder when
Windows asks for new h/w driver. It is safe to choose “Yes” for the waring window.
Confirm “SAMSUNG BlueFin USB Downloader” Installed.
Refer to Next Page.
** If Windows doesn’t ask for USB driver, it means USB driver installation was
failed before. Open Hardware Manager then delete devices with?or!mark then try
again. If it doesn’t work, you need to right click on the device then try Driver
Update.
After installing PDA driver, Apollo shows the connection status if it is installed
properly.
4-5
SAMSUNG Proprietary-Contents may change without notice
This Document can not be used without Samsung's authorization
Array course control
4-6
SAMSUNG Proprietary-Contents may change without notice
This Document can not be used without Samsung's authorization
Array course control
4-2-4. USB Driver installation for MODEM
Hold “7 + *” key and insert power supplied test cable when use equipment set 1 or
Hold “7+ *” key and press power on key when use equipment set 2.
Install Modem side driver.
Execute ‘Setup.exe’file under ‘i450_Apollo_Drivers\PHONE_driver’ folder when
Windows asks for new h/w driver.
Confirm “SAMSUNG USB Composite Device” Installed.
4-7
SAMSUNG Proprietary-Contents may change without notice
This Document can not be used without Samsung's authorization
Array course control
4-2-5. USB Driver installation
4-8
SAMSUNG Proprietary-Contents may change without notice
This Document can not be used without Samsung's authorization
4-2-6. Download the image using APOLLO
Execution Apollo.exe.
Select a Rom Image to download
Array course control
Check this field : 1. SGH-i450 (above GH4^)
4-9
SAMSUNG Proprietary-Contents may change without notice
This Document can not be used without Samsung's authorization
Array course control
Select the proper check option .
PDA stasus
- Bootloader : Update PDA Bootloader section.
- NV Clear : IMEI section erase.
You can see following message when you click this option
MODEM Status
- Boot Update : Update Modem Bootloader section.
4-10
SAMSUNG Proprietary-Contents may change without notice
This Document can not be used without Samsung's authorization
Array course control
Make sure that phone and host computer connection, click proper download
button.
PDA download :
MODEM download :
All download :
Hold 1, 4 keys and power on -> Blue screen with some information.
Hold 7, * keys and power on -> Blinking "MODEM DOWNLOAD"
on blue screen
Hold 4, 7 keys and power on -> Blinking "ALL DOWNLOAD" on blue screen
4-11
SAMSUNG Proprietary-Contents may change without notice
This Document can not be used without Samsung's authorization
Array course control
Do NOT interrupt downloading process.
- Pda download time: About 1 min.
- Modem download time : About 2 min.
- All download time: About 3 min.
Confirm Download Complete.
SGH-i450 will be reboot when PDA download complete.
-
4-12
SAMSUNG Proprietary-Contents may change without notice
This Document can not be used without Samsung's authorization
4-2-7. Troubleshooting
Unable to install USB driver.
Try another Download equipment
Try another SGH-i450.
Consult to R&D team.
Download stops in the middle.
Close and launch Apollo again then try again.
Check the battery is charged enough.
Download doesn’t start
Check the connection between Apollo and a SGH-i450.
Check the image that is not damaged.
Array course control
Select an image and download again.
Phone doesn’t boot up after downloading.
Check the release version of PDA and MODEM. They should be same.
Make sure that rom image, and then try to download.
4-13
SAMSUNG Proprietary-Contents may change without notice
This Document can not be used without Samsung's authorization
Array course control
4-14
SAMSUNG Proprietary-Contents may change without notice
This Document can not be used without Samsung's authorization
5. Exploded View and Parts List
5-1. Cellular phone Exploded View
QMW01
QIF01
QFR01
QSD01
QCR58
QFU01
QKP01
QCA02
QAR01
QMO01
QLC01
QPC01
QFL01
QHI01
QCR12
QCK02
QVO01
QSH03
QCA01
QSP01
QCR06
QMP01
QMI01
QAN05
QCK01
QSH01
QSH02
QRF03
QRE01
QCR06
QBA01
QCR12
QFL04
QBA00
5-3
SAMSUNG Proprietary-Contents may change without notice
This Document can not be used without Samsung's authorization