Samsung SCW-F200 Reference Information

2. NAM Programming

2.1 Switching the NAM(Numeric Assignment Module) writing mode

If you performs NAM writing mode, you have to enter the password, '4, 7, *, 8, 6, 9, #, 0, 8, #, 9'.

Keypads using in NAM writing mode are as follows :

0~9 : numberic keys

, # : Use to specify the variable which include several value.

VOLUME KEY : Use to switch the next item

CLR : Use to retouch a wrong digit

HOOK ON : Use to end a NAM writing mode

STO : Use to store data and switching the next function

RCL : Use to swich the last menu

Caution

-If you enter the NAM progrm mode, the last data displays on screen . When you need not change the data, press VOLUME key to go to the next item.

-You can modify the data by entering a new data. And if you enter a wrong digit, press CLR to delete the last digit.

-If you enter a wrong digit in the middle of NAM entering, continue to enter the next digits. After that check and modify the data using volume key.

-While you check the data using volume, you can store the data by pressing STO key.

-When you enter the NAM, as there are necessary information enter the phone number and LOCK code and press STO key.

When you enter NAM programming, display following three items.

1 GENERAL ; Display the variable used commonly NAM.

2 Setup NAM ; Display the variable of CDMA used commonly when you select NAM.

If you don't store the data by pressing STO key after modifying as explains, the data does not change. You can check the data by pressing VOLUME key without changing the data.

Samsung Electronics

2-1

NAM Programming

2-2 Explaination about each item

2-2-1 GENERAL

When swiching the next item, press volume or STO key. (When you press STO key, store entered data.)

ESN ( Electronic serial number) : In Service Program, current ESN cannot be modifyed and entered but displayed. If you want to modify ESN, special ESN Write Program is needed. For more details, refer to 'ESN Writer manual'

CAI version (common Air Interface version) : The version of the Common Air Interface supported by the mobile. Default setting is 2, CAI Version is not reset by user.

SCM (Station Class Mark) : Station Class Mark(SCM) displays the power class, transmission, slotted, dual mode. SCM is not reset by user.

Lock Code : Default lock cord is 0000. It can be entered from 0000 to 9999.

SLOT Mode : Determine the slot mode of the mobile (using Yes-slot mode)

When changing ‘YES’ or ‘NO’, press or #.

Slot Index : Determine the solt mode index on slot mode the mobile.

The extent of index is from 0 to 9. The bigger the index of set, the longer sleeping time. The sleeping time is longer the more power is saved. Default setting is 2.

2-2	Samsung Electronics

NAM Programming

2-2-2 Setup NAM

When you swich the next item, press volume or STO key. (If you press STO key, store the entered variable).

IMSI_MCC : Enter Mobile Country Code Default setting is 000.

IMSI_MNC : Enter Mobile Network Code Default setting is 00.

CDMA TEL NO : It is telephone number for CDMA

CDMA Pref : Select preferred system in using CDMA.

Home only, A only, A pref, B only, B pref.

CDMA ACCOLC : CDMA ACCESS OVERLOAD CLASS Default setting is 0.

Pchn Sys A : This is preferred system in using A system. OOO set 779, OOO set 0.

Pchn Sys B : This is preferred system in using B system. Default setting of OOO is 779 channel. Default setting of OOO is 486 channel.

Schn Sys A : This is the second preferred system in using A system. OOO set 738, OOO set 0.

Schn Sys B : This is the second preferred system in using B system. Default setting of OOO is 738 channel. Default setting of OOO is 568 channel.

CD Acq SID 1~CD Acq SID 6 : CDMA Acquisition SID. Enables you to set up to six SIDs. Default setting is 0, ranges from 0 to 32,767.

CD lock SID 1~CD lock SID 6 : CDMA lock SID

Enables you to set up to six SIDs.

Default setting is 0, ranges from 0 to 32767

CDMA Home SID : CDMA home SID Default setting is 'YES'.

Specify the Autonomous requisition in the home system.

SID #1 : (SID,NID) This is the first SID in using list.

NID #1 : (SID,NID) This is the first NID in using list.

SID #2 : (SID,NID) This is the second SID in using list.

NID #2 : (SID,NID) This is the second NID in using list.

SID #3 : (SID,NID) This is the third SID in using list

SID #3 : (SID,NID) This is the third NID in using list

SID #4 : (SID,NID) This is the fourth SID in using list

SID #4 : (SID,NID) This is the fourth NID in using list

SID #5 : (SID,NID) This is the fifth SID in using list

SID #5 : (SID,NID) This is the fifth NID in using list

Samsung Electronics

2-3