Samsung SCC-B2331BP, SCC-B2031BP, SCC-B2031P, SCC-B2331B, SCC-B2331P User Manual

SCC-B2331(P) SCC-B2031P

DIGITAL COLOR CAMERA

user manual

imagine the possibilities

Thank you for purchasing this Samsung product. To receive more complete service, please register your product at

www.samsungsecurity.com

ENG FRE

ENG

GER SPA

ITA

Safety information

CAUTION

RISK OF ELECTRIC SHOCK.

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE REAR COVER. NO USER SERVICEABLE PARTS

INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL..

This symbol indicates high voltage is present inside. It is dangerous to make any kind of contact with any inside part of this product.

This symbol alerts you that important literature concerning operation and maintenance has been included with this product.

WARNING

To prevent damage which may result in ﬁ re or electric shock hazard, do not expose this appliance

•

to rain or moisture.

WARNING

Be sure to use only the standard adapter that is speciﬁ ed in the speciﬁ cation sheet. Using any other adapter could cause ﬁ re, electrical shock, or damage to the product

Incorrectly connecting the power supply or replacing battery may cause explosion, ﬁ re, electric

2. shock, or damage to the product.

Do not connect multiple cameras to a single adapter. Exceeding the capacity may cause

3. abnormal heat generation or ﬁ re.

Securely plug the power cord into the power receptacle. Insecure connection may cause ﬁ re.

When installing the camera, fasten it securely and ﬁ rmly. A falling camera may cause personal

5. injury.

Do not place conductive objects (e.g. screwdrivers, coins, metal things, etc.) or containers ﬁ lled

6. with water on top of the camera. Doing so may cause personal injury due to ﬁ re, electric shock, or falling objects.

Do not install the unit in humid, dusty, or sooty locations. Doing so may cause ﬁ re or electric

7. shock.

If any unusual smells or smoke come from the unit, stop using the product. In such case,

8. immediately disconnect the power source and contact the service center. Continued use in such a condition may cause ﬁ re or electric shock.

If this product fails to operate normally, contact the nearest service center. Never disassemble

9. or modify this product in any way. (SAMSUNG is not liable for problems caused by unauthorized modiﬁ cations or attempted repair.)

2 – DIGITAL COLOR CAMERA

Safety information

10.

When cleaning, do not spray water directly onto parts of the product. Doing so may cause ﬁ re or electric shock.

CAUTION

Do not drop objects on the product or apply strong shock to it. Keep away from a location

1. subject to excessive vibrationor magnetic interference.

Do not install in a location subject to high temperature (over 50°C), low temperature (below -

2. 10°C), or high humidity. Doing so may cause ﬁ re or electric shock.

If you want to relocate the already installed product, be sure to turn off the power and then move

3. or reinstall it.

Remove the power plug from the outlet when then there is a lightning. Neglecting to do so may

4. cause ﬁ re or damage to the product.

Keep out of direct sunlight and heat radiation sources. It may cause ﬁ re.

Install it in a place with good ventilation.

Avoid aiming the camera directly towards extremely bright objects such as sun, as this may

7. damage the CCD image sensor.

Apparatus shall not be exposed to dripping or splashing and no objects ﬁ lled with liquids, such as

8. vases, shall be placed on the apparatus.

The Mains plug is used as a disconnect device and shall stay readily operable at any time.

ENG

English – 3

Important Safety Instructions

Read these instructions.

Keep these instructions.

Heed all warnings.

Follow all instructions.

Do not use this apparatus near water.

Clean only with dry cloth.

Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

Do not install near any heat sources such as radiators, heat registers, or other apparatus (including

8. ampliﬁ ers) that produce heat.

Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades

9. with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If the provided plug does not ﬁ t into your outlet, consult an electrician for replacement of the obsolete outlet.

Protect the power cord from being walked on or pinched particularly at plugs,

10. convenience receptacles, and the point where they exit from the apparatus.

Only use attachments/accessories speciﬁ ed by the manufacturer.

11.

Use only with cart, stand, tripod, bracket, or table speciﬁ ed by the manufacturer, or

12. sold with the apparatus.

Unplug this apparatus when a card is used. Use caution when moving the cart/

13. apparatus combination to avoid injury from tip-over.

Refer all servicing to qualiﬁ ed service personnel. Servicing is required when the apparatus has been

14. damaged in any way, such as powersupply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

4 – DIGITAL COLOR CAMERA

Contents

Introduction

Features 6 PRODUCT & ACCESSORIES 7 Part Names and Functions 8

Installation

Connecting the Auto Iris Lens Connector 11 Mounting the lens 11 Connecting cables and checking operation 12

How to use OSD Menu

Using Icons in the Menu 13 Main Menu 13 Proﬁ le 14 Camera Setup 16 Intelligence 22 Privacy zone Setup Other Set 24 System Information 25 Language 25

Speciﬁ cations

Speciﬁ cations 26

ENG

English – 5

Introduction

FEATURES

High Resolution

❖

This camera has realized high resolution of 600 lines using the top-notch full digital image processing and

•

special algorithm technologies.

Intelligent Motion Detection & Tracking

❖

•

This is an intelligent function that automatically detects a motion of an object. You can set a virtual fence so it sounds an alert if an object passes / enters /exits the virtual fence or virtual area.

❖

XDR (eXtended Dynamic Range)

Actively controls the gamma compensation in the way it operates the ambient luminance contrast in a

•

certain pixel unit to determine the optimal visibility.

DAY/NIGHT

❖

•

This function can make the IR Cut ﬁ ltering function inactive under the illumination below the normal value.

❖

High Sensitivity

It implements images of high sensitivity using the up-to-date SONY Super-HAD Progressive CCD.

•

Low Illumination

❖

It uses the digital signal technologies such as low illumination and Day/Night functions that make your camera

•

identify objects even in the worst environment.

Superior Backlight Adjustment

❖

•

When an object has a bright illumination or sunlight behind it, this camera automatically improves the shaded object picture quality.

❖

Digital Power Synchronization

The full digital Line Lock function directly adjusts the vertical camera synchronization to enhance the

•

operationability and reliability of this camera.

Output Signal Setting

❖

•

You can set the following Video output signals: Image reversion (Horizontal, Vertical, or both), Privacy, Horizontal/Vertical proﬁ ling, and digital zooming.

OSD(On Screen Display) Menu

❖

•

OSD menu is provided to display the status of camera and to conﬁ gure the functions interactively.

❖

Coaxial Cable Communication

This is a remote control function that overlaps the coaxial cable (for a transfer of the video signal) with the

•

control signal. In installation or repair, this helps you control the communication controller (optional) without additional cabling.

6 – DIGITAL COLOR CAMERA

PRODUCT & ACCESSORIES

Product & Accessories❖

Main Product

•

Accessories

•

Camera Holder(Mount)

C Mount Adapter

Camera

Introduction

User’s Manual

Lens Connector

ENG

Auto Iris

English – 7

Introduction

PART NAMES AND FUNCTIONS

Side View❖

Mount Adapter Fixing Grooves

Auto Iris Lens Connector

Auto Iris Lens Control Cable

Auto Iris Lens Connector

•

This groove is used for screwing the mount adapter, a part of the bracket where the camera will be installed.

Auto Iris Lens Control Cable

•

This cable transmits the power and signals from the camera for controlling the Auto Iris Lens.

Mount Adapter Fixing Grooves

•

These grooves are used when ﬁ xing screws of the mount adapter connected to the bracket when installing the camera on it.

Note :



When the camera lens becomes dirty, softly clean it with a lens tissue or a cloth soaked in pure ethanol.

–

8 – DIGITAL COLOR CAMERA

Camera Lens

Introduction

Rear Panel❖

<AC220V~240V(SCC-B2031P)>

ENG

p q

English – 9

Introduction

n Input/Output Connector

This connector has input and output ports for

and alarm output signals.

No. Function Description

1 ALARM OUT

2 GND Grounding Port.

3 TRIGGER IN

4 SHUTTER (S0)

5 SHUTTER (S1)

6 SHUTTER (S2)

7 5V OUT

o SETUP Switch

This switch is used to set the function or property. When this switch is pressed for at least 2 seconds, the MAIN MENU appears.

(Left/Right)

: By pressing this switch left or right, you can move left or right on the menu or change the

 : When you press this switch in the menu, the selected function is conﬁ rmed. To enter a submenu, press

p Power Display LED

When the power is normally connected, the red LED lights.

q Video OUT Port

This is connected to the Video Input Port of the monitor and it outputs the Video signals.

r GND

This is a grounding port.

s Power Connection Port

This is connected to the Power cable.

displayed value.

(Up/Down) :

By pressing this switch up or down, you can move up or down on the menu.

this button.

Alarm out port for motion detection. (Open collector type)

Displays the current still image when it receives the Trigger signal. (Normal Open Type)

This is a port for selecting an external high speed shutter mode. If connected in LOW (0V), it will become ON inside.

Power supply port for RS-485 JIG. Use within typical DC +5V 100mA

10 – DIGITAL COLOR CAMERA

CONNECTING THE AUTO IRIS LENS CONNECTOR

Installation

MOUNTING THE LENS

When using the CS lens

Mount the CS lens by rotating it clockwise as shown in the picture:

CS lens

CS 렌즈

Connect each uncovered shutter control cables to the Auto Iris Lens Connector as the following

DC Control

No.

1 Damp(-) Power (+12V)

2 Damp(+) Not applicable

3 Drive(+) Video Signal

4 Drive(-) Ground

Note :



You can switch a control type of the lens in the menu.

–

Type

Video Control Type

When using the C lens

After mounting the C-mount adapter by rotating it clockwise, turn the C lens clockwise until it is ﬁ xed as shown in the picture.

C 렌즈

C lens

English – 11

ENG

Installation

CONNECTING CABLES AND CHECKING OPERATION

①

Connect one end of the BNC cable to the VIDEO OUT Port on the rear of the camera.

② Connect another end of the BNC cable to the

VIDEO IN Port on the monitor.

Video In Terminal of Monitor Rear Surface

BNC cable

1 . A L

R 2 .

D 3

T T R

(

)

(

)

T D A

Y / N

T I N

6 7

③

Finally connect the power adapter to the camera. You can connect 2 lines of the power adapter to the camera using the Slot Head screwdriver as shown in the picture. (GND: cable with the white stripe line)

1 . A

L A

R 2 .

D 3

T T R

( S

(

)

(

)

A Y

/N I

G H

I N

1 2

3 4

5 6

Video Out Terminal

12 – DIGITAL COLOR CAMERA

Note :



Connect any power source of AC 24V and DC 12V

–

irrespective of polarity.

How to use OSD Menu

USING ICONS IN THE MENU

 (EXIT)

•

Exits the menu setting. Before you exits the menu setting, select SAVE to save your settings, or select QUIT to cancel.

 (RET)

•

Returns to the previous menu.

 (HOME)

•

Returns to the main menu.

 (SAVE)

•

Used to save your settings of MASK AREA, PRIVACY ZONE and more. Once you save your settings, they will remain even if you select QUIT in the menu.

 (DEL)

•

Used to deletes your settings of MASK AREA, PRIVACY ZONE and more. Once you delete your settings, they will not be restored even if you select QUIT in the menu.

MAIN MENU

ÃÃMAIN MENUÃÃ

PROFILE



CAMERA SET INTELLIGENCE PRIVACY ZONE

OTHER SET

SYSTEM INFO

LANGUAGE



PROFILE

•

You can set a mode according to the camera installation conditions.

CAMERA SET

•

Conﬁ gure Camera related functions and data.

INTELLIGENCE

•

You can conﬁ gure the settings of motion detection,tracking and more.

PRIVACY ZONE

•

You can conﬁ gure the privacy related settings.

OTHER SET

•

You can conﬁ gure for Factory Defaults, and more.

SYSTEM INFO.

•

Displays the system information including the camera version and communication settings.

LANGUAGE

•

Select a preferred one from the supported languages.

ENG

English – 13

How to use OSD Menu

PROFILE

STANDARD

ITS BACKLIGHT DAY/NIGHT

GAMING CUSTOM

 

In the PROFILE menu, you can conﬁ gure the following camera settings at once.

CAMERA SET Menu

IRIS ALC ALC ALC ALC ALC

ALC -- ---

MOTION (F.FAST)--- (F.FAST)--- NORM (F.FAST)--- SLOW

DNR MID MID MID MID MID SHUTTER OFF AUTO1/250 OFF OFF OFF SENS-UP AUTOx4 AUTOx2 AUTOx4 AUTOx4 AUTOx4

XDR MID MID MID MID MID

STANDARD ITS BACKLIGHT DAY/NIGHT GAMING

Sub-menus

LENS DC DC DC DC DC

LEVEL 0 0 0 0 0

BACKLIGHT OFF OFF OFF OFF OFF

WEIGHT

WHITE BAL

User setting

allowed

User setting

allowed

User setting

allowed

MID

User setting

allowed

User setting

allowed

User setting

allowed

User setting

14 – DIGITAL COLOR CAMERA

allowed

How to use OSD Menu

CAMERA SET Menu

WHITE BAL DAY DAY/NIGHT DAY DAY/NIGHT DAY

DAY -- ---

NIGHT - - - - -

BRIGHTNESS

DETAIL 2 2 2 2 2

ITS

❖

STANDARD ITS BACKLIGHT DAY/NIGHT GAMING

Sub-menus

MODE ATW2 ATW1 ATW1 ATW1 ATW1

RED00 000

BLUE 0 0 0 0 0

User setting

allowed

MODE OFF ATW2 OFF ATW2 OFF

User setting

RED

allowed

User setting

BLUE

allowed

User setting

MID

allowed

User setting

allowed

User setting

allowed

User setting

MID

allowed

User setting

allowed

User setting

allowed

ENG

It will be set automatically so you can easily check the trafﬁ c conditions.

BACKLIGHT

❖

It will be set automatically so you can distinguish the object from the background in a severe backlighting scene.

DAY/NIGHT

❖

It will be set automatically so it optimizes to the day or night conditions, respectively.

GAMING

❖

It will be set automatically to help you take a picture in a regular indoor lighting condition.

English – 15

How to use OSD Menu

CAMERA ID [OFF, ON]

CAMERA SETUP

eCAMERA SETf

CAMERA ID OFF IRIS ALC MOTION (F.FAST)--DNR MID SHUTTER OFF SENS-UP AUTO X4 FLICKERLESS (OFF)--XDR MID  

DAY/NIGHT AUTO WHITE BAL  DIGITAL ZOOM DETAIL [2] V-SYNC INT AGC COLOR SUP REVERSE OFF POSI/NEGA + PIP OFF  

DIS OFF

 

Setup the general functions of zoom camera module. Use the

cdef

16 – DIGITAL COLOR CAMERA

OFF

LOW

switch to select a menu item.

❖

CAMERA ID

ABCDEFGHIJKLMNOPQRSTUVWXYZ0 123456789 :?-+*()/

ffee

SP LOCATION

CAMERA-1..................

...........................

  

The CAMERA ID menu is used for you to assign a unique name to a camera. If you press the SETUP switch with the CAMERA ID menu selected, you will see the appropriate screen.

You can enter up to 54 alphanumeric or special characters for the CAMERA ID. Select LOCATION and press the SETUP switch to move the display position of the CAMERA ID.

❖

IRIS [ALC, ELC]

The IRIS menu is used if you want to adjust the intensity of radiation incoming to the camera.

•

ALC (Automatic Light Control)

① If you press the SETUP switch with an ALC-

based sub menu selected, you will see the appropriate screen.

ALC

LENS DC LEVEL [00]----I---BACKLIGHT OFF

  

The LENS menu is used if you select a type of the AI lens.

For normal operation, you must select DC for a DC-type lens, and select VIDEO for a VIDEOtype lens.

The LEVEL menu is used to adjust the

How to use OSD Menu

overall brightness, where “+” will increase the brightness and “–” will decrease it.

② If you set the BACKLIGHT option to BLC,

you will see a menu where you can set the BLC area.

you can set the desired BLC zone by deﬁ ning the size and location.

ALC

LENS DC LEVEL [00]----I---BACKLIGHT BLC AREA USER <SIZE> <LOCATION>

  

If you use an ordinary camera in a scene with an intensive backlight, the object will be displayed dark on the monitor affected by the backlight. To solve this problem, you can use the BLC(Back Light Compensation) function to improve the sharpness of the image in such a high contrast scene.

Namely, it improves the sharpness of the picture in outdoor scenery as well as indoor.

ELC (Electronic Light Control)

•

If you press the SETUP switch when the ELC

①

submenu is selected, the corresponding screen appears. You can make the ELC (Electronic Light Control) function active or not.

ELC

LEVEL [00]----I---BACKLIGHT OFF

  

② In similar to ALC setting, you can specify the

BLC area.

ELC

LEVEL [00]----I---BACKLIGHT BLC AREA USER <SIZE> <LOCATION>

  

AGC

❖

[OFF, VERY LOW, LOW, MID, HIGH, VERY HIGH, USER, FIX]

The AGC (Auto Gain Control) menu is used to set the AGC level of the camera. When the AGC is active, the camera automatically increases the sensitivity by amplifying the Video signal when the strength of the signal falls below the normal value.

If OFF or FIX mode is selected in the SENS-UP menu, you can specify the AGC level.

If you press the SETUP switch with a USER sub menu selected, you will see the appropriate screen.

AGC USER

LEVEL [16]

  

In USER mode, you can break down the level in 16 steps from VERY LOW to VERY HIGH to your preference.

ENG

English – 17

How to use OSD Menu

SHUTTER

AGC FIX

LEVEL [01]

  

If you press the SETUP switch with a FIX sub menu selected, you will see the appropriate screen.

As a ﬁ xed value of the AGC gain is used in FIX mode, you can select one of the 16 detailed levels from VERY LOW to VERY HIGH before ﬁ xing it.



Note :

If the DAY/NIGHT menu of the CAMERA SET is set to

–

AUTO, the AGC menu will be deactivated. If FLICKERLESS is set to ON, the AGC FIX mode will be

–

disabled.

❖

MOTION



Note :

–

DNR

❖

[S.SLOW, SLOW, NORM, FAST, F.FAST]

The MOTION menu is used to adjust the strength of the AGC level for a control of the camera motion. This is available only if the SENS-UP menu is set to AUTO. You can select one from S.SLOW, SLOW, NORM, FAST and F.FAST for the AGC level.

If you monitor a fast moving object in a low contrast scene, select F.FAST while select S.SLOW for a hardly moving object in the same lighting condition.

If the DAY/NIGHT menu of the CAMERA SET is set to AUTO, the MOTION menu will be deactivated.

[OFF,LOW,MID,HIGH, USER(1~16)]

You can conﬁ gure the DNR (Digital Noise Reduction) related settings.

Reduces the noise on the screen. This is especially useful for a severely distorted screen.

You can set the level if you set DNR to USER.

❖

[OFF, AUTO 1/100(PAL:1/120), AUTO 1/250, AUTO 1/500, AUTO 1/1000, AUTO 1/2000, AUTO 1/4000, AUTO 1/10K , 1/100(PAL:1/120), 1/250, 1/500, 1/1000, 1/2000, 1/4000, 1/10K , EXT]

The SHUTTER menu is used to set the ﬁ xed high-speed electronic shutter, auto high speed electronic shutter and external high speed electronic shutter(EXT).

You can select one of 7 options from 1/100(PAL:1/120) to 1/10K for the ﬁ xed high speed electronic shutter, which is mostly used for imaging a fast moving object.

The auto high speed electronic shutter operates as the ﬁ xed high speed shutter in a high contrast scene but automatically focuses the target if the iris opens fully in a low contrast scene like in ELC mode. When it gets brighter back, the mode will switch to the ﬁ xed high speed electronic shutter mode.

However, the auto high speed shutter operates properly only in a camera featuring a DC or VIDEO lens.

In external high speed electronic shutter (EXT) mode, you can select one of 8 modes from OFF through 1/100(PAL:1/120) to 1/10K for the high speed electronic shutter. It works as the high speed electronic shutter. You can select an option using SHUTTER(S0), SHUTTER(S1) and SHUTTER(S2) on the rear.

Connect each of the terminals to GND.

See the below table for the operation.

SHUTTER(S0) SHUTTER(S1) SHUTTER(S2)

OFF

(NTSC: 1/60,

OFF OFF OFF

PAL:1/50)

1/100

(PAL:1/120)

ON OFF OFF

1/250 OFF ON OFF

1/500 ON ON OFF

1/1000 OFF OFF ON

18 – DIGITAL COLOR CAMERA

How to use OSD Menu

1/2000 ON OFF ON

1/4000 OFF ON ON

1/10K ON ON ON

Note :



If IRIS mode is set to ELC, the SHUTTER menu will be

–

deactivated as you adjust the brightness using the electronic shutter.

If the SENS-UP function is set to AUTO, only items of

–

OFF and AUTO are available in the SHUTTER menu. If the FLICKERLESS function is set to ON, the SHUTTER menu

–

will be deactivated.

SENS-UP

❖

[OFF, AUTO X2, AUTO X4, AUTO X6, AUTO X8, AUTO X12, AUTO X16, AUTO X24, AUTO X32, AUTO X48, AUTO X64, AUTO X96, AUTO X128, AUTO X256, AUTO X512, FIX X2, FIX X4, FIX X6, FIX X8, FIX X12, FIX X16, FIX X24, FIX X32, FIX X48, FIX X64, FIX X96, FIX X128, FIX X256, FIX X512]

Automatically detects the ambient level of darkness in the dark or low contrast scene to extend the accumulated time, keeping the image bright and sharp



Note :

If the SHUTTER option is set to ﬁ xed electronic shutter or

–

EXT mode, the SENS-UP menu will be deactivated. If FLICKERLESS is set to ON, the FIX mode of the SENS-

–

UP menu will be disabled.

FLICKERLESS [OFF, ON]

❖

If set to ON, the shutter speed will be ﬁ xed to 1/100(PAL:1/120) second. This will prevent possible screen distortion due to a mismatch between the vertical sync frequency and the blinking frequency of the lighting.

Note :



If the IRIS function is set to ELC, the Flickerless menu will

–

be deactivated. If the SHUTTER menu is set to AUTO, FIX or EXT mode, the Flickerless menu will be deactivated.

If the SENS-UP function is set to FIX mode, the Flickerless

–

menu will be deactivated.

If AGC is set to FIX mode, the FLICKERLESS function will

–

be disabled.

XDR (eXtended Dynamic Range)

❖

[OFF, LOW, MID, HIGH]

Actively controls the gamma compensation in the way it operates the ambient luminance contrast in a certain pixel unit to determine the optimal visibility.

Select one from OFF, LOW, MID and HIGH. Closing to HIGH will increase the compensation level.

DAY/NIGHT

❖

DAY

•

If set to DAY, it will be ﬁ xed to DAY mode regardless of the ambient conditions.

NIGHT

•

If set to NIGHT, it will be ﬁ xed to Black-and-White mode regardless of the ambient conditions. If you press the SETUP switch with a NIGHT sub menu selected, you will see a menu where you can set Burst to OFF/ON. If BURST is set to ON, the Burst signal will output together with the black-and-white composite video signal. If BURST is set to OFF, the Burst signal does not output. You can set the BURST option to OFF/ON, or select to output the Burst signal in NIGHT mode.

AUTO

•

The camera will automatically switch between DAY and NIGHT mode, according to the lighting condition.

If you press the SETUP switch with an AUTObased sub menu selected, you will see the appropriate screen.

[DAY,NIGHT,AUTO,EXT]

ENG

English – 19

How to use OSD Menu

AUTO BURST OFF DAYÆNIGHT BRIGHTNESS MID DWELL TIME 2S NIGHTÆDAY BRIGHTNESS MID DWELL TIME 5S MASK AREA 1 2

  

You can set the BURST option to OFF/ON, or select to output the Burst signal in NIGHT mode.

You can select from LOW, MID and HIGH for the brightness of DAYÆNIGHT, which is a brightness level in switching from the color ﬁ lter to Black-and-White. Closing to LOW from HIGH will switch the ﬁ lter in a low contrast scene. The DWELL TIME of DAYÆNIGHT is a time required to determine the need for switching the ﬁ l t e r .

You can select from LOW, MID and HIGH for the brightness of NIGHTÆDAY, which is a brightness level in switching from the Black-andWhite ﬁ lter to color. Closing to LOW from HIGH will switch the ﬁ lter in a low contrast scene. The DWELL TIME of NIGHTÆDAY is a time required to determine the need for switching the ﬁ l t e r .

The MASK menu is used to prevent a ﬁ lter switch error or inability of determining the switch in existence of a high spot light source at night. If you press the SETUP switch in item 1 or 2 of the MASK menu, you will see a menu where you can specify an area to mask.



MASK AREA



<SIZE>  <LOCATION>

    

You can specify Mask 1 and 2 simultaneously.

20 – DIGITAL COLOR CAMERA

The mask is used only for determining the ﬁ lter switch and any excessive bright area at night will be masked.



Note :

If BACKLIGHT is set to BLC, the MASK AREA function will

–

be deactivated.

EXT

•

This enables an auto switch between DAY and NIGHT mode using the interface with the external

sensor.

WHITE BAL [DAY/NIGHT]

❖

If you want to adjust the color scheme, use the

WHITE BALANCE function.

DAY

•

In DAY mode, you can set the color values of RED and BLUE. The screen will be displayed in

colors according to your settings.

WHITE BAL

DAY/NIGHT DAY MODE AWC RED [00]----I--- BLUE [00]----I--- R-GAIN [0248] B-GAIN [0247]

  

Note :



You can set the values of R-GAIN and B-GAIN only in

–

AWC mode.

•

NIGHT

Use the NIGHT mode if you want to set the white balance differently according to the ambient luminance.

If the NIGHT mode is set to OFF, the white balance will always operate as set in DAY mode; if not to OFF, the camera will switch to as set in

How to use OSD Menu

DAY/NIGHT mode according to the brightness. In NIGHT mode, you can set the values of RED,

BLUE and BRIGHTNESS. The screen will be displayed in colors according to your settings.

WHITE BAL

DAY/NIGHT NIGHT BRIGHTNESS MID MODE AWC RED [00]----I--- BLUE [00]----I--- R-GAIN [0248] B-GAIN [0247]







You can set the digital zoom factor and position. If you press the SETUP switch with the DIGITAL ZOOM function set to ON, you will see the appropriate screen.

When the zoom factor and position are deﬁ ned, the digital zoom function will operate.

DIGITAL ZOOM

RATIO [X1.0] < LOCATION >



Note :



You can set the values of R-GAIN and B-GAIN only in

–

AWC mode. If AGC is set to OFF or FIX, you can not access the

–

NIGHT menu.

–

For adjusting the white balance, the following 5 modes are provided:

•

ATW1(Auto Tracing White Balance mode

1): The camera can automatically adjust the color temperature in real time, according to the ambient conditions. The color temperature ranges from approx. 2500K to 9300K.

•

ATW2: The color temperature ranges from approx. 2,000K to 10,000K.

•

AWC ( Auto White Balance Control): If you press the SETUP switch in the appropriate item position, Auto White Balance will perform once.

•

3200K : Set color temperature to 3200K

•

5600K : Set color temperature to 5600K

–

RED : Adjusts the strength of the red color.

–

BLUE : Adjusts the strength of the blue color.

–

R-GAIN/B-GAIN : Enables you to set the current color temperature manually.

–

BRIGHTNESS : Select a brightness level in switching from setting in DAY mode to setting in NIGHT mode.

❖

DIGITAL ZOOM [ON/OFF]

  

LOCATION : If you press the SETUP switch in the condition where the image is enlarged as much as the ratio setting, you can watch an invisible area of the effective screen as well using the

Note :



If the digital zoom factor is set to larger than 1x, the FENCE

–

function will be deactivated. The DIGITAL ZOOM function enlarges the pixel itself, which can cause deterioration of the quality.

DETAIL [0~3]

❖

cdef

switch.

Controls the horizontal or vertical distinction.

V-SYNC [INT, LINE]

❖

Select the vertical sync mode for INT or LINE. If you select INT, the camera will use the internal

synchronization. If selecting LINE, the camera will use the external

power source frequency for the synchronization. You can adjust the LL-PHASE.

English – 21

ENG

How to use OSD Menu

Note :



Use of DC 12V will ﬁ x V-SYNC to INT, which can not be

–

changed.

AGC COLOR SUP [LOW , MID, HIGH]

❖

Adjust the color scheme according to the AGC value.

REVERSE [OFF, H, V, H/V]

❖

Mirrors video signals horizontally, vertically, or both.

POSI/NEGA [+, -]

❖

Output as it is or mirror the video brightness signal.

PIP [OFF, ON]

❖

Displays a sub image together with the main image on the same screen using the Picture In Picture function.

Note :



If more than one privacy zone is set and the PRIVACY

–

SET is set to ON, the PIP function will be deactivated. If the INTELLIGENCE function is set to FENCE mode, the

–

PIP menu will be deactivated.

DIS [OFF, ON]

❖

Digital Image Stabilization will set the anti-shake compensation.

Note :



If you set DIS to ON, the compensation area will be

–

enlarged as set in the digital zoom factor. If you set the digital zoom factor to greater than the enlarged zoom factor for the compensation, the DIS function will be deactivated.

INTELLIGENCE

eINTELLIGENCEf

MOTION OFF sMASK AREA DISPLAY ON SENSITIVITY [4] RESOLUTION [5] ALARM OUT 

 

You can set the motion detection and tracking in the

INTELLIGENCE menu.

MOTION

❖

•

TRACKING

Detects and tracks a moving object.

•

DETECTION

Detects a moving object.

❖

MASK AREA [1~4]

Specify a detection exception area to mask. Select a mask number and specify the size and

position.

DISPLAY [ON, OFF]

❖

With the DISPLAY option set to ON, a motion or a set ADVANCED function will be displayed on the screen, if detected.

[OFF,TRACKING,DETECTION]



MASK AREA

<SIZE>  <LOCATION>

    

1 2 3 4



22 – DIGITAL COLOR CAMERA

How to use OSD Menu

SENSITIVITY [1~7]

❖

Set the sensitivity of the motion detection.

RESOLUTION [1~5]

❖

If setting it to high, the camera can detect even a trivial movement of the target.

ALARM OUT

❖

If you set a desired menu item to ON, the camera will sound an alert if it detect the appropriate motion.

ALARM OUT

MOTION ON

  

PRIVACY ZONE SETUP

ePRIVACY ZONEf

1 2 3 4 5 6 7 8 9 10 11

PRIVACY SET ON STYLE

 

The PRIVACY function will protect your privacy by screening the privacy area that you have speciﬁ ed during monitoring. You can specify up to 12 privacy zones.

If you set the PRIVACY SET to ON, your PRIVACY ZONE settings will be applied.

You can change the style to adjust the mosaic size and color of the PRIVACY ZONE.

ePRIVACY ZONEf

1 2 3 4 5 6 7 8 9 10 11

PRIVACY SET ON STYLE COLOR Y-LEVEL [128] RED [128] BLUE [128]



Use the

cdef

PRIVACY 1 through 12. Select one from PRIVACY 1~12 and press the

SETUP switch to conﬁ rm your setting. You can specify a pixel that moves as you change the PIXEL LEVEL to set the position.

switch to select one from

MOSAIC1

ENG



English – 23

How to use OSD Menu

PRIVACY ZONE SET1

PIXEL LEVEL [4] <POINT> <POSITION>

    

- How to set the point

You can set each position of the 4 points.

① If you press the SETUP switch in <POINT>,

you will see the points available in the

PRIVACY ZONE. Each time you press the SETUP switch, the points available will move.

② Use the

cdef

of each point. Set each position of the four points and press the SETUP switch to complete the positioning.

- How to set the position You can move the position of the overall area.

① By pressing the SETUP switch in

<POSITION>, you can move the overall

position of the privacy zone.

② Use the

position and press the SETUP switch to conﬁ rm it.

Note :



If more than one PRIVACY ZONE is speciﬁ ed and the

–

PRIVACY SET is set to ON, the PIP function will be deactivated.

If the 12th PRIVACY ZONE is speciﬁ ed, the LINE function

–

of FENCE will be deactivated.

switch to set the position

cdef

switch to move the

OTHER SET

eOTHER SETf

FACTORY DEFAULTS OSD COLOR BW

 

FACTORY DEFAULTS

❖

All the settings will be restored to the factory default. However, the settings of LANGUAGE will not be restored to the default.

OSD COLOR [BW, R/G/B]

❖

You can set the OSD(On-screen Display) color to COLOR or B/W.



24 – DIGITAL COLOR CAMERA

How to use OSD Menu

SYSTEM INFORMATION

eSYSTEM INFOf

TYPE 3_BOX_NOR_P SERIAL NO.

000000000000000

CAMERA VER. 0.50_090101

 

You can view the system information including the serial number, camera version..

LANGUAGE

eLANGUAGEf

ÃENGLISH

FRANÇAIS

DEUTSCH ESPAÑOL

ITALIANO

 

The camera supports 5 different languages.

Select a preferred language.

Initial Conﬁ guration Table

❖

Camera Conﬁ guration

•

CAMERA ID OFF

IRIS ALC

AGC VERY HIGH

MOTION (F.FAST)

DNR MID

SHUTTER OFF

SENS-UP

AUTO x4

FLICKERLESS (OFF)

XDR MID

DAY/NIGHT AUTO

DIGITAL ZOOM OFF

DETAIL [2]

AGC COLOR SUP MID

REVERSE OFF

POSI/NEGA +

PIP OFF

DIS OFF

V-SYNC INT

ENG

English – 25

Speciﬁ cations

SPECIFICATIONS

Items Sub-items SCC-B2331N

Camera Type

Image

Scanning

Min. Scene

Illumination

Functions

Resolution

Device 1/3” Super-HAD PS CCD

Pixels

System Interlace/Progressive

Scanning Line 525 lines

Frame 30frame/1sec

Horizontal Frequency

Vertical

Frequency

Number of Privacy Zone 12 (Polygonal Method)

eXtended Dynamic Range(XDR) Off/On (Level Setting)

Digital Noise Reduction(DNR) Off/On (Adaptive 3D+2D) Digital Image Stabilization(DIS)

Total 811 x 508

Effective 768 x 494

Internal Mode 15,734 Hz

Line-lock Mode 15,750 Hz

Internal Mode 59.94 Hz

Line-lock Mode 60 Hz

Sens-up F No. Level DAY NIGHT

OFF 1.2 50 IRE 0.4 Lux 0.4 Lux OFF 1.2 30 IRE 0.24 Lux 0.24 Lux

OFF 1.2 15 IRE 0.12 Lux 0.12 Lux 512 times 1.2 50 IRE 0.0008 Lux 0.0008 Lux 512 times 1.2 30 IRE 0.0005 Lux 0.0005 Lux 512 times 1.2 15 IRE 0.0002 Lux 0.0002 Lux

Day/Night DAY/NIGHT/AUTO/EXT

Motion Detection OFF/Tracking/Detection

D-Zoom x1 ~ x16 (x0.1 STEP)

PIP Off/On

High Speed Shutter 1/60 ~ 1/10Ksec (OSD/External Control)

Flickerless Off/On

Sens-Up x2 ~ x512

BLC Off/On (Area Setting) AGC Off/On (Max.Level Setting) ELC Off/On ( ~ 1/200K sec)

Line Lock Off/On (Phase Control)

Camera ID Off/On (Max.54ea/2Line)

White Balance ATW1/ATW2/AWC/3200K/5600K

Intelligent Video Fixed/Moved

Etc. Function Detail, Reverse(H/V), Posi/Nega

Horizontal 600 TV Lines

Vertical 350 TV Lines

CCTV Camera

Condition Min. Scene illumination

Off/On

26 – DIGITAL COLOR CAMERA

Speciﬁ cations

Items Sub-items SCC-B2331N

Video Output

S/N Ratio

Lens

Alarm

Remote

Control

Environmental

Conditions

Power

Physical

Speciﬁ cation

- VBS 1.0Vp-p, 75 Ω

S/N Ratio Approx. 52dB

Lens Drive Type MANUAL/AI(VIDEO/DC)

Mount Type CS/C

Input N/A

Output 1 Output

Coaxitron (Data On Coax cable) Yes (with SCX-RD100)

Operating Temperature -10˚C ~ +50˚C

Humidity Less than 90%

Power Requirement

Power Consumption

(With DC Lens)

LED Indicator Yes

Dimensions

(WxHxD)

Weight

Color Body Silver

Net 64(W) x 58(H) x 109.2(D) mm

Package 173(W) x 99(H) x 115(D) mm

Net 305g

Package 530g

AC24V ± 10%(60Hz ± 0.3Hz)

DC12V ± 10%

In normal operation : 2.2W

ENG

English – 27

Speciﬁ cations

Items Sub-items SCC-B2331P / SCC-B2031P

Camera Type

Image

Scanning

Min. Scene Illumination

Functions

Resolution

Device 1/3” Super-HAD PS CCD

Pixels

System Interlace/Progressive

Scanning Line 625 lines

Frame 25frame/1sec

Horizontal

Frequency

Vertical

Frequency

Number of Privacy Zone 12 (Polygonal Method)

eXtended Dynamic Range(XDR) Off/On (Level Setting)

Digital Noise Reduction(DNR) Off/On (Adaptive 3D+2D) Digital Image Stabilization(DIS)

Total 795 x 596

Effective 752 x 582

Internal Mode 15,625 Hz

Line-lock Mode 15,625 Hz

Internal Mode 50 Hz

Line-lock Mode 50 Hz

Sens-up F No. Level DAY NIGHT

OFF 1.2 50 IRE 0.4 Lux 0.4 Lux

OFF 1.2 30 IRE 0.24 Lux 0.24 Lux

OFF 1.2 15 IRE 0.12 Lux 0.12 Lux 512 times 1.2 50 IRE 0.0008 Lux 0.0008 Lux 512 times 1.2 30 IRE 0.0005 Lux 0.0005 Lux 512 times 1.2 15 IRE 0.0002 Lux 0.0002 Lux

Day/Night DAY/NIGHT/AUTO/EXT

Motion Detection OFF/Tracking/Detection

D-Zoom Max. x16

PIP Off/On

High Speed Shutter 1/50 ~ 1/10Ksec (OSD/External Control)

Flickerless Off/On

Sens-Up x2 ~ x512

BLC Off/On (Area Setting)

AGC Off/On (Max.Level Setting)

ELC Off/On ( ~ 1/200K sec)

Line Lock Off/On (Phase Control)

Camera ID Off/On (Max.54ea/2Line)

White Balance ATW1/ATW2/AWC/3200K/5600K

Intelligent Video Fixed/Moved

Etc. Function Detail, Reverse(H/V), Posi/Nega

Horizontal 600 TV Lines

Vertical 350 TV Lines

CCTV Camera

Condition Min. Scene illumination

Off/On

28 – DIGITAL COLOR CAMERA

Speciﬁ cations

Items Sub-items SCC-B2331P / SCC-B2031P

Video Output

S/N Ratio

Lens

Alarm

Remote

Control

Environmental

Conditions

Power

Physical

Speciﬁ cation

- VBS 1.0Vp-p, 75 Ω

S/N Ratio Approx. 52dB

Lens Drive Type MANUAL/AI(VIDEO/DC)

Mount Type CS/C

Input N/A

Output 1 Output

Coaxitron (Data On Coax cable) Yes (with SCX-RD100)

RS-485 Yes (Multi Protocol, 8ea)

Operating Temperature -10˚C ~ +50˚C

Humidity Less than 90%

Power Requirement

Power Consumption

(With DC Lens)

LED Indicator Yes

Dimensions

(WxHxD)

Weight

Color Body Silver

Net

Package 173(W) x 99(H) x 115(D) mm

Net

Package

SCC-B2331P : AC24V ± 10%(50Hz±0.3Hz)

DC12V ± 10%

SCC-B2031P : AC220V ± 10%(50Hz±0.3Hz)

In Normal operation : SCC-B2331P : 2.2W SCC-B2031P : 3.3W

SCC-B2331P : 64(W) x 58(H) x 109.2(D) mm SCC-B2031P : 64(W) x 58(H) x 129.2(D) mm

SCC-B2331P : Approx. 305g SCC-B2031P : Approx. 395g SCC-B2331P : Approx. 530g SCC-B2031P : Approx. 620g

ENG

English – 29

Correct Disposal of This Product (Waste Electrical & Electronic Equipment)

(Applicable in the European Union and other European countries with separate collection systems)

This marking on the product, accessories or literature indicates that the product and its electronic accessories (e.g. charger, headset, USB cable) should not be disposed of with other household waste at the end of their working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate these items from other types of waste and recycle them responsibly to promote the sustainable reuse of material resources.

Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take these items for environmentally safe recycling.

Business users should contact their supplier and check the terms and conditions of the purchase contract. This product and its electronic accessories should not be mixed with other commercial wastes for disposal.

+ 122 hidden pages