Samsung SCC-B2331BP, SCC-B2031BP, SCC-B2031P, SCC-B2331B, SCC-B2331P User Manual

SCC-B2331(P)

SCC-B2031P

DIGITAL COLOR CAMERA

user manual

ENG

FRE

GER

SPA

ITA

imagine the possibilities

Thank you for purchasing this Samsung product. To receive more complete service,

please register your product at

www.samsungsecurity.com

Safety information

CAUTION

RISK OF ELECTRIC SHOCK.

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE REAR COVER. NO USER SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL..

This symbol indicates high voltage is present inside. It is dangerous to make any kind of contact with any inside part of this product.

This symbol alerts you that important literature concerning operation and maintenance has been included with this product.

WARNING

•To prevent damage which may result in fire or electric shock hazard, do not expose this appliance to rain or moisture.

WARNING

1.Be sure to use only the standard adapter that is specified in the specification sheet. Using any other adapter could cause fire, electrical shock, or damage to the product

2.Incorrectly connecting the power supply or replacing battery may cause explosion, fire, electric shock, or damage to the product.

3.Do not connect multiple cameras to a single adapter. Exceeding the capacity may cause abnormal heat generation or fire.

4.Securely plug the power cord into the power receptacle. Insecure connection may cause fire.

5.When installing the camera, fasten it securely and firmly. A falling camera may cause personal injury.

6.Do not place conductive objects (e.g. screwdrivers, coins, metal things, etc.) or containers filled with water on top of the camera. Doing so may cause personal injury due to fire, electric shock, or falling objects.

7.Do not install the unit in humid, dusty, or sooty locations. Doing so may cause fire or electric shock.

8.If any unusual smells or smoke come from the unit, stop using the product. In such case, immediately disconnect the power source and contact the service center. Continued use in such a condition may cause fire or electric shock.

9.If this product fails to operate normally, contact the nearest service center. Never disassemble or modify this product in any way. (SAMSUNG is not liable for problems caused by unauthorized modifications or attempted repair.)

2 – DIGITAL COLOR CAMERA

Safety information

10.When cleaning, do not spray water directly onto parts of the product. Doing so may cause fire or electric shock.

CAUTION

	1.	Do not drop objects on the product or apply strong shock to it. Keep away from a location
		subject to excessive vibrationor magnetic interference.
	2.	Do not install in a location subject to high temperature (over 50°C), low temperature (below -
		10°C), or high humidity. Doing so may cause fire or electric shock.
	3.	If you want to relocate the already installed product, be sure to turn off the power and then move
		or reinstall it.
	4.	Remove the power plug from the outlet when then there is a lightning. Neglecting to do so may
		cause fire or damage to the product.
	5.	Keep out of direct sunlight and heat radiation sources. It may cause fire.
	6.	Install it in a place with good ventilation.
	7.	Avoid aiming the camera directly towards extremely bright objects such as sun, as this may
		damage the CCD image sensor.	ENG
	8.	Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as
		vases, shall be placed on the apparatus.
	9.	The Mains plug is used as a disconnect device and shall stay readily operable at any time.

English – 3

Important Safety Instructions

1.Read these instructions.

2.Keep these instructions.

3.Heed all warnings.

4.Follow all instructions.

5.Do not use this apparatus near water.

6.Clean only with dry cloth.

7.Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8.Do not install near any heat sources such as radiators, heat registers, or other apparatus (including amplifiers) that produce heat.

9.Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10.Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11.Only use attachments/accessories specified by the manufacturer.

12.Use only with cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus.

13.Unplug this apparatus when a card is used. Use caution when moving the cart/ apparatus combination to avoid injury from tip-over.

14.Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as powersupply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

4 – DIGITAL COLOR CAMERA

Contents

Introduction

Features		6
PRODUCT & ACCESSORIES		7
Part Names and Functions		8

Installation

Connecting the Auto Iris Lens Connector		11
Mounting the lens		11
Connecting cables and checking operation		12

How to use OSD Menu
Using Icons in the Menu	13
Main Menu	13
Profile	14
Camera Setup	16
Intelligence	22	ENG
Privacy zone Setup	23
Other Set	24
System Information	25
Language	25
Specifications
Specifications	26

English – 5

Introduction

FEATURES

High Resolution

•This camera has realized high resolution of 600 lines using the top-notch full digital image processing and special algorithm technologies.

Intelligent Motion Detection & Tracking

•This is an intelligent function that automatically detects a motion of an object. You can set a virtual fence so it sounds an alert if an object passes / enters /exits the virtual fence or virtual area.

XDR (eXtended Dynamic Range)

•Actively controls the gamma compensation in the way it operates the ambient luminance contrast in a certain pixel unit to determine the optimal visibility.

DAY/NIGHT

•This function can make the IR Cut filtering function inactive under the illumination below the normal value.

High Sensitivity

•It implements images of high sensitivity using the up-to-date SONY Super-HAD Progressive CCD.

Low Illumination

•It uses the digital signal technologies such as low illumination and Day/Night functions that make your camera identify objects even in the worst environment.

Superior Backlight Adjustment

•When an object has a bright illumination or sunlight behind it, this camera automatically improves the shaded object picture quality.

Digital Power Synchronization

•The full digital Line Lock function directly adjusts the vertical camera synchronization to enhance the operationability and reliability of this camera.

Output Signal Setting

•You can set the following Video output signals: Image reversion (Horizontal, Vertical, or both), Privacy, Horizontal/Vertical profiling, and digital zooming.

OSD(On Screen Display) Menu

•OSD menu is provided to display the status of camera and to configure the functions interactively.

Coaxial Cable Communication

•This is a remote control function that overlaps the coaxial cable (for a transfer of the video signal) with the control signal. In installation or repair, this helps you control the communication controller (optional) without additional cabling.

6 – DIGITAL COLOR CAMERA

Introduction

PRODUCT & ACCESSORIES

Product & Accessories

• Main Product

Camera	ENG

• Accessories

Camera Holder(Mount)	C Mount Adapter	User’s Manual	Auto Iris
			Lens Connector

English – 7

Introduction

PART NAMES AND FUNCTIONS

Side View

Mount Adapter

Fixing Grooves

	Auto Iris Lens	Camera Lens
	Connector

Auto Iris Lens

Control Cable

• Auto Iris Lens Connector

This groove is used for screwing the mount adapter, a part of the bracket where the camera will be installed.

•Auto Iris Lens Control Cable

This cable transmits the power and signals from the camera for controlling the Auto Iris Lens.

•Mount Adapter Fixing Grooves

These grooves are used when fixing screws of the mount adapter connected to the bracket when installing the camera on it.

Note :

–When the camera lens becomes dirty, softly clean it with a lens tissue or a cloth soaked in pure ethanol.

8 – DIGITAL COLOR CAMERA

Introduction

Rear Panel

	<AC24/DC12V (SCC-B2331(P))>
n	o

p	q
r
	s	ENG
	<AC220V~240V(SCC-B2031P)>

n	o
	p

s	q

English – 9

Introduction

n Input/Output Connector

This connector has input and output ports for and alarm output signals.

No.								Function	Description
1							ALARM OUT		Alarm out port for motion detection. (Open collector type)
2								GND	Grounding Port.
3							TRIGGER IN		Displays the current still image when it receives the Trigger signal.
									(Normal Open Type)
4							SHUTTER (S0)		This is a port for selecting an external high speed shutter mode.
									If connected in LOW (0V), it will become ON inside.
5							SHUTTER (S1)		This is a port for selecting an external high speed shutter mode.
									If connected in LOW (0V), it will become ON inside.
6							SHUTTER (S2)		This is a port for selecting an external high speed shutter mode.
									If connected in LOW (0V), it will become ON inside.
7								5V OUT	Power supply port for RS-485 JIG. Use within typical DC +5V 100mA

o SETUP Switch

This switch is used to set the function or property. When this switch is pressed for at least 2 seconds, the MAIN MENU appears.

ef(Left/Right) : By pressing this switch left or right, you can move left or right on the menu or change the displayed value.

cd(Up/Down) : By pressing this switch up or down, you can move up or down on the menu.

: When you press this switch in the menu, the selected function is confirmed. To enter a submenu, press this button.

pPower Display LED

When the power is normally connected, the red LED lights.

qVideo OUT Port

This is connected to the Video Input Port of the monitor and it outputs the Video signals.

rGND

This is a grounding port.

sPower Connection Port

This is connected to the Power cable.

10 – DIGITAL COLOR CAMERA

	Installation
CONNECTING THE AUTO IRIS LENS	MOUNTING THE LENS
CONNECTOR
	When using the CS lens
	Mount the CS lens by rotating it clockwise as shown
	in the picture:
	CS lens
	CS

Connect each uncovered shutter control cables to the Auto Iris Lens Connector as the following

	Pin	DC Control	Video Control Type
	No.	Type
	1	Damp(-)	Power (+12V)
	2	Damp(+)	Not applicable
	3	Drive(+)	Video Signal
	4	Drive(-)	Ground

Note :

–You can switch a control type of the lens in the menu.

ENG When using the C lens

After mounting the C-mount adapter by rotating it clockwise, turn the C lens clockwise until it is fixed as shown in the picture.

CClens

English – 11

Installation

CONNECTING CABLES AND CHECKING OPERATION

Connect one end of the BNC cable to the VIDEO OUT Port on the rear of the camera.

Connect another end of the BNC cable to the VIDEO IN Port on the monitor.

Finally connect the power adapter to the camera. You can connect 2 lines of the power adapter to the camera using the Slot Head screwdriver as shown in the picture.

(GND: cable with the white stripe line)

1.
32..ATGRLNIADRAM OUT 5.
4.	GGERIN 6.
	SHUTTER(SO) 87..

1	2	3	4	5
					6

SS5DVHHAUUYOTT/NUTTITEEGHRR((SST12IN))

7

8

Video In Terminal of Monitor Rear

Surface

BNC cable

Video Out Terminal

Note :

– Connect any power source of AC 24V and DC 12V irrespective of polarity.

12 – DIGITAL COLOR CAMERA

How to use OSD Menu

USING ICONS IN THE MENU

• (EXIT)

Exits the menu setting.

Before you exits the menu setting, select SAVE to save your settings, or select QUIT to cancel.

• (RET)

Returns to the previous menu.

• (HOME)

Returns to the main menu.

• (SAVE)

Used to save your settings of MASK AREA, PRIVACY ZONE and more.

Once you save your settings, they will remain even if you select QUIT in the menu.

• (DEL)

Used to deletes your settings of MASK AREA, PRIVACY ZONE and more.

Once you delete your settings, they will not be restored even if you select QUIT in the menu.

MAIN MENU

ÃÃMAIN MENUÃÃ

PROFILE

CAMERA SET INTELLIGENCE PRIVACY ZONE OTHER SET SYSTEM INFO LANGUAGE

• PROFILE

You can set a mode according to the camera installation conditions.

• CAMERA SET

Configure Camera related functions and data.	ENG
• INTELLIGENCE
You can configure the settings of motion
detection,tracking and more.

• PRIVACY ZONE

You can configure the privacy related settings.

• OTHER SET

You can configure for Factory Defaults, and more.

• SYSTEM INFO.

Displays the system information including the camera version and communication settings.

• LANGUAGE

Select a preferred one from the supported languages.

English – 13

How to use OSD Menu

PROFILE

ePROFILEf

ÃSTANDARD

ITS

BACKLIGHT DAY/NIGHT GAMING CUSTOM

In the PROFILE menu, you can configure the following camera settings at once.

CAMERA SET Menu
Previous	Sub-menus	STANDARD	ITS	BACKLIGHT	DAY/NIGHT	GAMING
Menu
IRIS		ALC	ALC	ALC	ALC	ALC
	ALC	-	-	-	-	-
	LENS	DC	DC	DC	DC	DC
	LEVEL	0	0	0	0	0
	BACKLIGHT	OFF	OFF	OFF	OFF	OFF
	WEIGHT	User setting	User setting	MID	User setting	User setting
		allowed	allowed		allowed	allowed
	WHITE BAL	User setting	User setting	User setting	User setting	User setting
		allowed	allowed	allowed	allowed	allowed
MOTION		(F.FAST)---	(F.FAST)---	NORM	(F.FAST)---	SLOW
DNR		MID	MID	MID	MID	MID
SHUTTER		OFF	AUTO1/250	OFF	OFF	OFF
SENS-UP		AUTOx4	AUTOx2	AUTOx4	AUTOx4	AUTOx4
XDR		MID	MID	MID	MID	MID

14 – DIGITAL COLOR CAMERA

How to use OSD Menu

CAMERA SET Menu
Previous	Sub-menus	STANDARD	ITS	BACKLIGHT	DAY/NIGHT	GAMING
Menu

	WHITE BAL	DAY	DAY/NIGHT	DAY	DAY/NIGHT	DAY
	DAY	-	-	-	-	-
	MODE	ATW2	ATW1	ATW1	ATW1	ATW1
	RED	0	0	0	0	0
	BLUE	0	0	0	0	0
	NIGHT	-	-	-	-	-
	BRIGHTNESS	User setting	MID	User setting	MID	User setting
		allowed		allowed		allowed
	MODE	OFF	ATW2	OFF	ATW2	OFF
	RED	User setting	0	User setting	0	User setting
		allowed		allowed		allowed
	BLUE	User setting	0	User setting	0	User setting
		allowed		allowed		allowed	ENG
	DETAIL	2	2	2	2	2

ITS

It will be set automatically so you can easily check the traffic conditions.

BACKLIGHT

It will be set automatically so you can distinguish the object from the background in a severe backlighting scene.

DAY/NIGHT

It will be set automatically so it optimizes to the day or night conditions, respectively.

GAMING

It will be set automatically to help you take a picture in a regular indoor lighting condition.

English – 15

How to use OSD Menu

CAMERA SETUP

eCAMERA SETf

	CAMERA ID					OFF
	IRIS					ALC
	MOTION			(F.FAST)---
	DNR					MID
	SHUTTER					OFF
	SENS-UP				AUTO X4
	FLICKERLESS				(OFF)---
	XDR					MID
				d
				c
					AUTO
	DAY/NIGHT
	WHITE BAL
	DIGITAL ZOOM					OFF
	DETAIL				[2]
	V-SYNC					INT
	AGC COLOR SUP					LOW
	REVERSE					OFF
	POSI/NEGA				+
	PIP					OFF
				d
				c
	DIS					OFF

Setup the general functions of zoom camera module. Use the cdefswitch to select a menu item.

CAMERA ID		[OFF, ON]
		CAMERA ID
	ABCDEFGHIJKLMNOPQRSTUVWXYZ0
123456789 :?-+*()/

SPffeeSP LOCATION

CAMERA-1..................

...........................

The CAMERA ID menu is used for you to assign a unique name to a camera. If you press the SETUP switch with the CAMERA ID menu selected, you will see the appropriate screen.

You can enter up to 54 alphanumeric or special characters for the CAMERA ID. Select LOCATION and press the SETUP switch to move the display position of the CAMERA ID.

IRIS	[ALC, ELC]

The IRIS menu is used if you want to adjust the intensity of radiation incoming to the camera.

•ALC (Automatic Light Control)

If you press the SETUP switch with an ALCbased sub menu selected, you will see the appropriate screen.

		ALC
LENS		DC
LEVEL		[00]----I----
BACKLIGHT		OFF

The LENS menu is used if you select a type of the AI lens.

For normal operation, you must select DC for a DC-type lens, and select VIDEO for a VIDEOtype lens.

The LEVEL menu is used to adjust the

16 – DIGITAL COLOR CAMERA

How to use OSD Menu

overall brightness, where “+” will increase the brightness and “–” will decrease it.

If you set the BACKLIGHT option to BLC, you will see a menu where you can set the BLC area.

you can set the desired BLC zone by defining the size and location.

			ALC
LENS					DC
LEVEL				[00]----I	----
	BACKLIGHT				BLC
	AREA				USER
	<SIZE>
	<LOCATION>

If you use an ordinary camera in a scene with an intensive backlight, the object will be displayed dark on the monitor affected by the backlight. To solve this problem, you can use the BLC(Back Light Compensation) function to improve the sharpness of the image in such a high contrast scene.

Namely, it improves the sharpness of the picture in outdoor scenery as well as indoor.

•ELC (Electronic Light Control)

If you press the SETUP switch when the ELC submenu is selected, the corresponding screen appears. You can make the ELC (Electronic Light Control) function active or not.

	ELC
LEVEL	[00]----I----
BACKLIGHT	OFF

In similar to ALC setting, you can specify the BLC area.

	ELC
LEVEL	[00]----I----
BACKLIGHT			BLC
AREA			USER
<SIZE>
<LOCATION>

	AGC
	[OFF, VERY LOW, LOW, MID, HIGH, VERY
	HIGH, USER, FIX]
	The AGC (Auto Gain Control) menu is used to
	set the AGC level of the camera. When the AGC	ENG
	is active, the camera automatically increases the
	sensitivity by amplifying the Video signal when
	the strength of the signal falls below the normal
	value.
	If OFF or FIX mode is selected in the SENS-UP
	menu, you can specify the AGC level.
	If you press the SETUP switch with a USER
	sub menu selected, you will see the appropriate
	screen.

AGC USER

LEVEL [16]

In USER mode, you can break down the level in 16 steps from VERY LOW to VERY HIGH to your

preference.

English – 17

How to use OSD Menu

AGC FIX

LEVEL [01]

If you press the SETUP switch with a FIX sub menu selected, you will see the appropriate screen.

As a fixed value of the AGC gain is used in FIX mode, you can select one of the 16 detailed levels from VERY LOW to VERY HIGH before fixing it.

Note :

–If the DAY/NIGHT menu of the CAMERA SET is set to AUTO, the AGC menu will be deactivated.

–If FLICKERLESS is set to ON, the AGC FIX mode will be disabled.

MOTION

[S.SLOW, SLOW, NORM, FAST, F.FAST]

The MOTION menu is used to adjust the strength of the AGC level for a control of the camera motion. This is available only if the SENS-UP menu is set to AUTO.

You can select one from S.SLOW, SLOW, NORM, FAST and F.FAST for the AGC level.

If you monitor a fast moving object in a low contrast scene, select F.FAST while select S.SLOW for a hardly moving object in the same lighting condition.

Note :

–If the DAY/NIGHT menu of the CAMERA SET is set to AUTO, the MOTION menu will be deactivated.

DNR	[OFF,LOW,MID,HIGH, USER(1~16)]

You can configure the DNR (Digital Noise Reduction) related settings.

Reduces the noise on the screen.

This is especially useful for a severely distorted screen.

You can set the level if you set DNR to USER.

SHUTTER

[OFF, AUTO 1/100(PAL:1/120), AUTO 1/250, AUTO 1/500, AUTO 1/1000, AUTO 1/2000, AUTO 1/4000, AUTO 1/10K , 1/100(PAL:1/120), 1/250, 1/500, 1/1000, 1/2000, 1/4000, 1/10K , EXT]

The SHUTTER menu is used to set the fixed high-speed electronic shutter, auto high speed electronic shutter and external high speed electronic shutter(EXT).

You can select one of 7 options from 1/100(PAL:1/120) to 1/10K for the fixed high speed electronic shutter, which is mostly used for imaging a fast moving object.

The auto high speed electronic shutter operates as the fixed high speed shutter in a high contrast scene but automatically focuses the target if the iris opens fully in a low contrast scene like in ELC mode. When it gets brighter back, the mode will switch to the fixed high speed electronic shutter mode.

However, the auto high speed shutter operates properly only in a camera featuring a DC or VIDEO lens.

In external high speed electronic shutter (EXT) mode, you can select one of 8 modes from OFF through 1/100(PAL:1/120) to 1/10K for the high speed electronic shutter. It works as the high speed electronic shutter. You can select an option using SHUTTER(S0), SHUTTER(S1) and SHUTTER(S2) on the rear.

Connect each of the terminals to GND. See the below table for the operation.

SHUTTER(S0) SHUTTER(S1) SHUTTER(S2)

	OFF
	(NTSC: 1/60,	OFF	OFF	OFF
	PAL:1/50)
	1/100	ON	OFF	OFF
	(PAL:1/120)
	1/250	OFF	ON	OFF
	1/500	ON	ON	OFF
	1/1000	OFF	OFF	ON

18 – DIGITAL COLOR CAMERA

How to use OSD Menu

1/2000	ON	OFF	ON
1/4000	OFF	ON	ON
1/10K	ON	ON	ON

Note :

–If IRIS mode is set to ELC, the SHUTTER menu will be deactivated as you adjust the brightness using the electronic shutter.

–If the SENS-UP function is set to AUTO, only items of OFF and AUTO are available in the SHUTTER menu.

–If the FLICKERLESS function is set to ON, the SHUTTER menu will be deactivated.

SENS-UP

[OFF, AUTO X2, AUTO X4, AUTO X6, AUTO X8, AUTO X12, AUTO X16, AUTO X24, AUTO X32, AUTO X48, AUTO X64, AUTO X96, AUTO X128, AUTO X256, AUTO X512, FIX X2, FIX X4, FIX X6, FIX X8, FIX X12, FIX X16, FIX X24, FIX X32, FIX X48, FIX X64, FIX X96, FIX X128, FIX X256, FIX X512]

Automatically detects the ambient level of darkness in the dark or low contrast scene to extend the accumulated time, keeping the image bright and sharp

Note :

–If the SHUTTER option is set to fixed electronic shutter or EXT mode, the SENS-UP menu will be deactivated.

–If FLICKERLESS is set to ON, the FIX mode of the SENSUP menu will be disabled.

FLICKERLESS

[OFF, ON]

If set to ON, the shutter speed will be fixed to 1/100(PAL:1/120) second. This will prevent possible screen distortion due to a mismatch between the vertical sync frequency and the blinking frequency of the lighting.

Note :

–If the IRIS function is set to ELC, the Flickerless menu will be deactivated. If the SHUTTER menu is set to AUTO, FIX or EXT mode, the Flickerless menu will be deactivated.

–If the SENS-UP function is set to FIX mode, the Flickerless menu will be deactivated.

–If AGC is set to FIX mode, the FLICKERLESS function will be disabled.

XDR (eXtended Dynamic Range) [OFF, LOW, MID, HIGH]

Actively controls the gamma compensation in the way it operates the ambient luminance contrast in a certain pixel unit to determine the optimal visibility.

Select one from OFF, LOW, MID and HIGH. Closing to HIGH will increase the compensation level.

DAY/NIGHT

[DAY,NIGHT,AUTO,EXT]

• DAY

If set to DAY, it will be fixed to DAY mode regardless of the ambient conditions.

• NIGHT	ENG
If set to NIGHT, it will be fixed to Black-and-White
mode regardless of the ambient conditions.
If you press the SETUP switch with a NIGHT sub
menu selected, you will see a menu where you can
set Burst to OFF/ON.
If BURST is set to ON, the Burst signal will output
together with the black-and-white composite video
signal. If BURST is set to OFF, the Burst signal does
not output.
You can set the BURST option to OFF/ON, or
select to output the Burst signal in NIGHT mode.

• AUTO

The camera will automatically switch between DAY and NIGHT mode, according to the lighting condition.

If you press the SETUP switch with an AUTObased sub menu selected, you will see the appropriate screen.

English – 19

How to use OSD Menu

	AUTO
BURST			OFF
DAYÆNIGHT
BRIGHTNESS			MID
DWELL TIME			2S
NIGHTÆDAY
BRIGHTNESS			MID
DWELL TIME			5S
MASK AREA			1 2

You can set the BURST option to OFF/ON, or select to output the Burst signal in NIGHT mode.

You can select from LOW, MID and HIGH for the brightness of DAYÆNIGHT, which is a brightness level in switching from the color filter to Black-and-White. Closing to LOW from HIGH will switch the filter in a low contrast scene.

The DWELL TIME of DAYÆNIGHT is a time required to determine the need for switching the filter.

You can select from LOW, MID and HIGH for the brightness of NIGHTÆDAY, which is a brightness level in switching from the Black-and- White filter to color. Closing to LOW from HIGH will switch the filter in a low contrast scene.

The DWELL TIME of NIGHTÆDAY is a time required to determine the need for switching the filter.

The MASK menu is used to prevent a filter switch error or inability of determining the switch in existence of a high spot light source at night. If you press the SETUP switch in item 1 or 2 of the MASK menu, you will see a menu where you can specify an area to mask.

MASK AREA

<SIZE> <LOCATION>

You can specify Mask 1 and 2 simultaneously.

The mask is used only for determining the filter switch and any excessive bright area at night will be masked.

Note :

–If BACKLIGHT is set to BLC, the MASK AREA function will be deactivated.

•EXT

This enables an auto switch between DAY and NIGHT mode using the interface with the external sensor.

WHITE BAL

[DAY/NIGHT]

If you want to adjust the color scheme, use the

WHITE BALANCE function.

• DAY

In DAY mode, you can set the color values of RED and BLUE. The screen will be displayed in colors according to your settings.

WHITE BAL

DAY/NIGHT					DAY
MODE				AWC
RED		[00]----I----
BLUE		[00]----I----
R-GAIN			[0248]
B-GAIN			[0247]

Note :

–You can set the values of R-GAIN and B-GAIN only in AWC mode.

•NIGHT

Use the NIGHT mode if you want to set the white balance differently according to the ambient luminance.

If the NIGHT mode is set to OFF, the white balance will always operate as set in DAY mode; if not to OFF, the camera will switch to as set in

20 – DIGITAL COLOR CAMERA

How to use OSD Menu

DAY/NIGHT mode according to the brightness.

In NIGHT mode, you can set the values of RED, BLUE and BRIGHTNESS. The screen will be displayed in colors according to your settings.

	WHITE BAL
DAY/NIGHT			NIGHT
BRIGHTNESS				MID
MODE			AWC
RED		[00]----I----
BLUE		[00]----I----
R-GAIN		[0248]
B-GAIN		[0247]

Note :

–You can set the values of R-GAIN and B-GAIN only in AWC mode.

–If AGC is set to OFF or FIX, you can not access the

NIGHT menu.

–For adjusting the white balance, the following 5 modes are provided:

•ATW1(Auto Tracing White Balance mode 1): The camera can automatically adjust the color temperature in real time, according to

the ambient conditions. The color temperature ranges from approx. 2500K to 9300K.

•ATW2: The color temperature ranges from approx. 2,000K to 10,000K.

•AWC ( Auto White Balance Control): If you press the SETUP switch in the appropriate item position, Auto White Balance will perform once.

•3200K : Set color temperature to 3200K

•5600K : Set color temperature to 5600K

–RED : Adjusts the strength of the red color.

–BLUE : Adjusts the strength of the blue color.

–R-GAIN/B-GAIN : Enables you to set the current color temperature manually.

–BRIGHTNESS : Select a brightness level in switching from setting in DAY mode to setting in

NIGHT mode.

DIGITAL ZOOM

[ON/OFF]

You can set the digital zoom factor and position. If you press the SETUP switch with the DIGITAL ZOOM function set to ON, you will see the appropriate screen.

When the zoom factor and position are defined, the digital zoom function will operate.

DIGITAL ZOOM

RATIO		[X1.0]
< LOCATION >

- LOCATION : If you press the SETUP switch in the
condition where the image is enlarged as much as the	ENG
ratio setting, you can watch an invisible area of the
effective screen as well using the cdefswitch.

Note :

–If the digital zoom factor is set to larger than 1x, the FENCE function will be deactivated.

The DIGITAL ZOOM function enlarges the pixel itself, which can cause deterioration of the quality.

DETAIL [0~3]

Controls the horizontal or vertical distinction.

V-SYNC

[INT, LINE]

Select the vertical sync mode for INT or LINE.

If you select INT, the camera will use the internal synchronization.

If selecting LINE, the camera will use the external power source frequency for the synchronization.

You can adjust the LL-PHASE.

English – 21

How to use OSD Menu

Note :

–Use of DC 12V will fix V-SYNC to INT, which can not be changed.

AGC COLOR SUP

[LOW , MID, HIGH]

Adjust the color scheme according to the AGC value.

REVERSE

[OFF, H, V, H/V]

Mirrors video signals horizontally, vertically, or both.

POSI/NEGA

[+, -]

Output as it is or mirror the video brightness signal.

PIP

[OFF, ON]

Displays a sub image together with the main image on the same screen using the Picture In Picture function.

Note :

–If more than one privacy zone is set and the PRIVACY SET is set to ON, the PIP function will be deactivated.

–If the INTELLIGENCE function is set to FENCE mode, the PIP menu will be deactivated.

DIS

[OFF, ON]

Digital Image Stabilization will set the anti-shake compensation.

Note :

–If you set DIS to ON, the compensation area will be enlarged as set in the digital zoom factor.

If you set the digital zoom factor to greater than the enlarged zoom factor for the compensation, the DIS function will be deactivated.

INTELLIGENCE

eINTELLIGENCEf

MOTION			OFF
sMASK AREA	1 2 3 4
DISPLAY			ON
SENSITIVITY	[4]
RESOLUTION	[5]
ALARM OUT

You can set the motion detection and tracking in the

INTELLIGENCE menu.

MOTION

[OFF,TRACKING,DETECTION]

•TRACKING

Detects and tracks a moving object.

•DETECTION

Detects a moving object.

MASK AREA [1~4]

Specify a detection exception area to mask.

Select a mask number and specify the size and position.

-MASK AREA

<SIZE> <LOCATION>

DISPLAY [ON, OFF]

With the DISPLAY option set to ON, a motion or a set ADVANCED function will be displayed on the screen, if detected.

22 – DIGITAL COLOR CAMERA

How to use OSD Menu

SENSITIVITY

[1~7]

Set the sensitivity of the motion detection.

RESOLUTION

[1~5]

If setting it to high, the camera can detect even a trivial movement of the target.

ALARM OUT

If you set a desired menu item to ON, the camera will sound an alert if it detect the appropriate motion.

	ALARM OUT
MOTION		ON

s

PRIVACY ZONE SETUP

	ePRIVACY ZONEf
1	2	3	4	5	6
7	8	9	10	11	12
PRIVACY SET					ON
STYLE				MOSAIC1

The PRIVACY function will protect your privacy by screening the privacy area that you have specified during monitoring. You can specify up to 12 privacy zones.

If you set the PRIVACY SET to ON, your PRIVACY
ZONE settings will be applied.	ENG
You can change the style to adjust the mosaic size
and color of the PRIVACY ZONE.

ePRIVACY ZONEf
1	2	3	4	5	6
7	8	9	10	11	12
PRIVACY SET					ON
STYLE				COLOR
Y-LEVEL			[128]
RED			[128]
BLUE			[128]

Use the cdefswitch to select one from

PRIVACY 1 through 12.

Select one from PRIVACY 1~12 and press the SETUP switch to confirm your setting. You can specify a pixel that moves as you change the PIXEL LEVEL to set the position.

English – 23

How to use OSD Menu

PRIVACY ZONE SET1

PIXEL LEVEL				[4]
<POINT>
<POSITION>

- How to set the point

You can set each position of the 4 points.

If you press the SETUP switch in <POINT>, you will see the points available in the PRIVACY ZONE. Each time you press the SETUP switch, the points available will move.

Use the cdefswitch to set the position of each point. Set each position of the four points and press the SETUP switch to complete the positioning.

-How to set the position

You can move the position of the overall area.

By pressing the SETUP switch in <POSITION>, you can move the overall position of the privacy zone.

Use the cdefswitch to move the position and press the SETUP switch to confirm it.

Note :

–If more than one PRIVACY ZONE is specified and the PRIVACY SET is set to ON, the PIP function will be deactivated.

–If the 12th PRIVACY ZONE is specified, the LINE function of FENCE will be deactivated.

OTHER SET

eOTHER SETf
FACTORY DEFAULTS
OSD COLOR	BW

FACTORY DEFAULTS

All the settings will be restored to the factory default.

However, the settings of LANGUAGE will not be restored to the default.

OSD COLOR

[BW, R/G/B]

You can set the OSD(On-screen Display) color to COLOR or B/W.

24 – DIGITAL COLOR CAMERA

How to use OSD Menu

SYSTEM INFORMATION

eSYSTEM INFOf

TYPE	3_BOX_NOR_P
SERIAL NO. 000000000000000
CAMERA VER.	0.50_090101

You can view the system information including the serial number, camera version..

LANGUAGE

eLANGUAGEf

ÃENGLISH FRANÇAIS DEUTSCH ESPAÑOL ITALIANO

The camera supports 5 different languages.

Select a preferred language.

	Initial Configuration Table
	• Camera Configuration
	CAMERA ID	OFF
	IRIS	ALC
	AGC	VERY HIGH
	MOTION	(F.FAST)
	DNR	MID
	SHUTTER	OFF
	SENS-UP	AUTO x4
	FLICKERLESS	(OFF)	ENG
	XDR	MID
	DAY/NIGHT	AUTO
	DIGITAL ZOOM	OFF
	DETAIL	[2]
	AGC COLOR SUP	MID
	REVERSE	OFF
	POSI/NEGA	+
	PIP	OFF
	DIS	OFF
	V-SYNC	INT

English – 25

Specifications

SPECIFICATIONS

Items

Sub-items

SCC-B2331N

Camera Type

CCTV Camera

Device

1/3” Super-HAD PS CCD

Image

Pixels

Total

811 x 508

Effective

768 x 494

System

Interlace/Progressive

Scanning Line

525 lines

Frame

30frame/1sec

Scanning

Horizontal

Internal Mode

15,734 Hz

Frequency

Line-lock Mode

15,750 Hz

Vertical

Internal Mode

59.94 Hz

Frequency

Line-lock Mode

60 Hz

Condition

Min. Scene illumination

Sens-up

F No.

Level

DAY

NIGHT

OFF

1.2

50

IRE

0.4

Lux

0.4

Lux

Min. Scene

OFF

1.2

30

IRE

0.24

Lux

0.24

Lux

Illumination

OFF

1.2

15

IRE

0.12

Lux

0.12

Lux

512 times

1.2

50

IRE

0.0008

Lux

0.0008

Lux

512 times

1.2

30

IRE

0.0005

Lux

0.0005

Lux

512 times

1.2

15

IRE

0.0002

Lux

0.0002

Lux

Number of Privacy Zone

12 (Polygonal Method)

Day/Night

DAY/NIGHT/AUTO/EXT

Motion Detection

OFF/Tracking/Detection

eXtended Dynamic Range(XDR)

Off/On (Level Setting)

D-Zoom

x1 ~ x16 (x0.1 STEP)

PIP

Off/On

High Speed Shutter

1/60 ~ 1/10Ksec (OSD/External Control)

Flickerless

Off/On

Sens-Up

x2 ~ x512

Functions

BLC

Off/On (Area Setting)

AGC

Off/On (Max.Level Setting)

ELC

Off/On ( ~ 1/200K sec)

Line Lock

Off/On (Phase Control)

Camera ID

Off/On (Max.54ea/2Line)

White Balance

ATW1/ATW2/AWC/3200K/5600K

Digital Noise Reduction(DNR)

Off/On (Adaptive 3D+2D)

Digital Image Stabilization(DIS)

Off/On

Intelligent Video

Fixed/Moved

Etc. Function

Detail, Reverse(H/V), Posi/Nega

Resolution

Horizontal

600 TV Lines

Vertical

350 TV Lines

26 – DIGITAL COLOR CAMERA

			Specifications
Items	Sub-items		SCC-B2331N
Video Output	-		VBS 1.0Vp-p, 75 Ω
S/N Ratio	S/N Ratio		Approx. 52dB
Lens	Lens Drive Type		MANUAL/AI(VIDEO/DC)
	Mount Type		CS/C
Alarm	Input		N/A
	Output		1 Output
Remote	Coaxitron (Data On Coax cable)		Yes (with SCX-RD100)
Control
Environmental	Operating Temperature		-10˚C ~ +50˚C
Conditions	Humidity		Less than 90%
	Power Requirement		AC24V ± 10%(60Hz ± 0.3Hz)
			DC12V ± 10%
Power	Power Consumption		In normal operation : 2.2W
	(With DC Lens)
	LED Indicator		Yes	ENG
	Dimensions	Net	64(W) x 58(H) x 109.2(D) mm
	(WxHxD)	Package	173(W) x 99(H) x 115(D) mm
Physical		Net	305g
Specification	Weight
		Package	530g
	Color	Body	Silver

English – 27

Specifications

Items

Sub-items

SCC-B2331P / SCC-B2031P

Camera Type

CCTV Camera

Device

1/3” Super-HAD PS CCD

Image

Pixels

Total

795 x 596

Effective

752 x 582

System

Interlace/Progressive

Scanning Line

625 lines

Frame

25frame/1sec

Scanning

Horizontal

Internal Mode

15,625 Hz

Frequency

Line-lock Mode

15,625 Hz

Vertical

Internal Mode

50 Hz

Frequency

Line-lock Mode

50 Hz

Condition

Min. Scene illumination

Sens-up

F No.

Level

DAY

NIGHT

OFF

1.2

50

IRE

0.4

Lux

0.4

Lux

Min. Scene

OFF

1.2

30

IRE

0.24

Lux

0.24

Lux

Illumination

OFF

1.2

15

IRE

0.12

Lux

0.12

Lux

512 times

1.2

50

IRE

0.0008

Lux

0.0008

Lux

512 times

1.2

30

IRE

0.0005

Lux

0.0005

Lux

512 times

1.2

15

IRE

0.0002

Lux

0.0002

Lux

Number of Privacy Zone

12 (Polygonal Method)

Day/Night

DAY/NIGHT/AUTO/EXT

Motion Detection

OFF/Tracking/Detection

eXtended Dynamic Range(XDR)

Off/On (Level Setting)

D-Zoom

Max. x16

PIP

Off/On

High Speed Shutter

1/50 ~ 1/10Ksec (OSD/External Control)

Flickerless

Off/On

Sens-Up

x2 ~ x512

Functions

BLC

Off/On (Area Setting)

AGC

Off/On (Max.Level Setting)

ELC

Off/On ( ~ 1/200K sec)

Line Lock

Off/On (Phase Control)

Camera ID

Off/On (Max.54ea/2Line)

White Balance

ATW1/ATW2/AWC/3200K/5600K

Digital Noise Reduction(DNR)

Off/On (Adaptive 3D+2D)

Digital Image Stabilization(DIS)

Off/On

Intelligent Video

Fixed/Moved

Etc. Function

Detail, Reverse(H/V), Posi/Nega

Resolution

Horizontal

600 TV Lines

Vertical

350 TV Lines

28 – DIGITAL COLOR CAMERA

			Specifications
Items	Sub-items		SCC-B2331P / SCC-B2031P
Video Output	-		VBS 1.0Vp-p, 75 Ω
S/N Ratio	S/N Ratio		Approx. 52dB
Lens	Lens Drive Type		MANUAL/AI(VIDEO/DC)
	Mount Type		CS/C
Alarm	Input		N/A
	Output		1 Output
Remote	Coaxitron (Data On Coax cable)		Yes (with SCX-RD100)
Control	RS-485		Yes (Multi Protocol, 8ea)
Environmental	Operating Temperature		-10˚C ~ +50˚C
Conditions	Humidity		Less than 90%
			SCC-B2331P : AC24V ± 10%(50Hz±0.3Hz)
	Power Requirement		DC12V ± 10%
			SCC-B2031P : AC220V ± 10%(50Hz±0.3Hz)
Power			In Normal operation :
	Power Consumption		SCC-B2331P : 2.2W
	(With DC Lens)		SCC-B2031P : 3.3W	ENG
	LED Indicator		Yes
	Dimensions	Net	SCC-B2331P : 64(W) x 58(H) x 109.2(D) mm
			SCC-B2031P : 64(W) x 58(H) x 129.2(D) mm
	(WxHxD)
		Package	173(W) x 99(H) x 115(D) mm
Physical		Net	SCC-B2331P : Approx. 305g
Specification			SCC-B2031P : Approx. 395g
	Weight
			SCC-B2331P : Approx. 530g
		Package
			SCC-B2031P : Approx. 620g
	Color	Body	Silver

English – 29

Correct Disposal of This Product (Waste Electrical & Electronic Equipment)

(Applicable in the European Union and other European countries with separate collection systems)

This marking on the product, accessories or literature indicates that the product and its electronic accessories (e.g. charger, headset, USB cable) should not be disposed of with other household waste at the end of their working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate these items from other types of waste and recycle them responsibly to promote the sustainable reuse of material resources.

Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take these items for environmentally safe recycling.

Business users should contact their supplier and check the terms and conditions of the purchase contract. This product and its electronic accessories should not be mixed with other commercial wastes for disposal.