Samsung SCC-B2315P, SCC-B2015P User Manual

WDR DAY/NIGHT COLOUR CAMERA

SCC-B2315(P)/SCC-B2015P

User Manual

ENG

GER

FRE

SPA

ITA

Safety Precautions

CAUTION

RISK OF ELECTRIC

SHOCK DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE REAR
COVER. NO USER SERVICEABLE PARTS
INSIDE. REFER TO QUALIFIED SERVICE
PERSONNEL.

This symbol indicates high voltage is present inside. It is dangerous
to make any kind of contact with any inside part of this product.

This symbol alerts you that important literature concerning
operation and maintenance has been included with this product.

To prevent damage which may result in fire or electric shock hazard, do
not expose this appliance to rain or moisture.

WARNING

1. Be sure to use only the standard adapter that is specified in the
specification sheet. Using any other adapter could cause fire,
electrical shock, or damage to the product

2. Incorrectly connecting the power supply or replacing battery may
cause explosion, fire, electric shock, or damage to the product.

3. Do not connect multiple cameras to a single adapter. Exceeding the
capacity may cause abnormal heat generation or fire.

4. Securely plug the power cord into the power receptacle. Insecure
connection may cause fire.

5. When installing the camera, fasten it securely and firmly. A falling
camera may cause personal injury.

6. Do not place conductive objects (e.g. screwdrivers, coins, metal
things, etc.) or containers filled with water on top of the camera.
Doing so may cause personal injury due to fire, electric shock, or
falling objects.

7. Do not install the unit in humid, dusty, or sooty locations. Doing so
may cause fire or electric shock.

8. If any unusual smells or smoke come from the unit, stop using the
product. In such case, immediately disconnect the power source and
contact the service centre. Continued use in such a condition may
cause fire or electric shock.

9. If this product fails to operate normally, contact the nearest service
centre. Never disassemble or modify this product in any way.
(SAMSUNG is not liable for problems caused by unauthorized
modifications or attempted repair.)

1

0. When cleaning, do not spray water directly onto parts of the product.
Doing so may cause fire or electric shock.

2 3

2

ENG

CAUTION

1. Do not drop objects on the product or apply strong shock to it. Keep
away from a location subject to excessive vibration or magnetic
interference.

2. If you want to relocate the already installed product, be sure to turn
off the power and then move or reinstall it.

3. Remove the power plug from the outlet when then there is a
lightning. Neglecting to do so may cause fire or damage to the
product.

4. Keep out of direct sunlight and heat radiation sources. It may cause
fire.

5. Install it in a place with good ventilation.

6. Avoid aiming the camera directly towards extremely bright objects
such as sun, as this may damage the CCD image sensor.

7. Apparatus shall not be exposed to dripping or splashing and no
objects filled with liquids, such as vases, shall be placed on the
apparatus.

8. The Mains plug is used as a disconnect device and shall stay readily
operable at any time.

FCC Statement

This device complies with part 15 of the FCC Rules. Operation is subject
to the following two conditions:

1) This device may not cause harmful interference, and

2) This device must accept any interference received including
interference that may cause undesired operation.

Note

This equipment has been tested and found to comply with the limits
for a Class A digital device, pursuant to part 15 of FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area
is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.

Important Safety Instructions

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in

accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators,

heat registers, or other apparatus (including amplifiers)
that produce heat.

9. Do not defeat the safety purpose of the polarized or

grounding-type plug. A polarized plug has two blades with
one wider than the other. A grounding type plug has two
blades and a third grounding prong. The wide blade or
the third prong is provided for your safety. If the provided
plug does not fit into your outlet, consult an electrician
for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched

particularly at plugs, convenience receptacles, and the
point where they exit from the apparatus.

11. Only use attachments/accessories specified by the

manufacturer.

12. Use only with cart, stand, tripod, bracket, or table

specified by the manufacturer, or sold with the apparatus.

13. Unplug this apparatus. When a cart is used, use caution

when moving the cart/apparatus combination to avoid
injury from tip-over.

14. Refer all servicing to qualified service personnel.

Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or plug
is damaged, liquid has been spilled or objects have fallen
into the apparatus, the apparatus has been exposed to
rain or moisture, does not operate normally, or been
dropped.

4 5

ENG

Contents

Safety Precautions ...... 2

Important Safety

Instructions ..................... 4

Contents ........................... 5

Overview ........................... 6

Special Features ........... 7

Part Names and

Functions ......................... 8

Side View ......................... 8

Rear Panel ....................... 10

Installation ....................... 13

Before Installation ......... 13

Checking the contents

of the package ..................

Things to keep in mind during

installation and use .............13

Connecting the Auto Iris

Lens Connector ................

Installing the Camera ... 15

Mounting the lens .............

Setting the ALC lens

selection switch ................

Adjusting the back focus .... 16

Connecting cables and

checking operation ...........

Camera Setup ................ 19

CAMERA ID ........................

IRIS ...................................... 20

WDR... ............................. 20

ALC... ............................... 21

ELC... ............................... 22

SHUTTER .........................22

AGC ................................... 23

MOTION ............................ 24

MOTION DET ................... 24

DAY/NIGHT ...................... 26

DAY... ...............................

NIGHT... ...........................

AUTO... ............................

EXT .................................. 29

WHITE BAL ...................... 29

13

PRIVACY ........................... 30

SPECIAL ........................... 31

LANGUAGE ..................... 31

V-SYNC ............................

14

DIGITAL ZOOM ...............

VIDEO SET ......................

15

DNR ................................. 33

FLICKERLESS ................. 33

16

SYSTEM INFO ................

RS-485 ............................... 34

EXIT ................................... 35

17

Product

Specifications ................ 36

20

27
28
28

31
32
32

34

Overview

This enriched WDR (Wide Dynamic Range) Day/Night camera can
clearly implement both dark and bright parts on the screen with the
dual shutter.
When a bright object such as window occupies a part of the screen, it
appears white in conventional cameras. But using the state-of-the-art
WDR function that this camera provides, you can see the clear image.
This Day/Night camera activates the colour mode when in the
illumination over the normal value. Otherwise it activates B/W (Black/
White) mode by removing the IR cut function, which can improve the
sensitivity for identifying objects even in a dark area.
It also incorporated the low speed shutter and Sens Up (Uses the
field accumulation method) functions to enhance the low illumination
feature.
This camera can be mainly used in the dark places such as
basement parking lots under comparatively low illumination. In
daytime, it displays the colour screen with a horizontal resolution of
540 lines but at night, it uses the Day/Night feature along with the
Sens Up function to identify objects in a dark area. You can also
connect the infrared ray emission equipment to this camera.

DAY/NIGHT

This function can make the IR Cut filtering function inactive under
the illumination below the normal value.

6 7

ENG

Special Features

High Sensitivity

It implements images of high sensitivity using the up-to-date Super­HAD P/S CCD.

WDR

The WDR function of this camera is the state-of-the-art technology
that can effectively enlarge the range for screen gain. It is mainly
used for taking photos for window scenes inside a building. Using
this technology, you can clearly see both indoor and outdoor
images, and can enjoy the excellent picture quality, which is
enabled by automatically adjusting the WDR level.

Low Illumination

It uses the digital signal technologies such as low illumination and
Day/Night functions that make your camera identify objects even in
the worst environment.

Superior Backlight Adjustment

When an object has a bright illumination or sunlight behind it, this
camera automatically improves the shaded object picture quality.

Digital Power Synchronization

The full digital Line Lock function directly adjusts the vertical
camera synchronization to enhance the operationability and
reliability of this camera.

High Resolution

This camera has realized high resolution of 540 lines using the
top-notch full digital image processing and special algorithm
technologies.

Output Signal Setting

You can set the following Video output signals: Image reversion
(Horizontal, Vertical, or both), Privacy, Horizontal/Vertical profiling,
and digital zooming.

Part Names and Functions

Side View

❚

1 Auto Iris Lens

Connector

5

ALC Lens

Selection Switch

4

Automatic Shutter

Lens Control Cable

1 Auto Iris Lens Connector

This groove is used for screwing the mount adapter, a part of the
bracket where the camera will be installed.

2 Mount Adapter Fixing Grooves

These grooves are used when fixing screws of the mount
adapter connected to the bracket when installing the camera on it.

3 Back Focus Control Bar

You can adjust the back focus by moving it up and down.

4 Automatic Shutter Lens Control Cable

This cable transmits the power and signals from the camera for
controlling the lens shutter.

2 Mount Adapter

Fixing Grooves

3 Back Focus

Control Bar

Camera Lens

8 9

ENG

5 ALC Lens Selection Switch

This switch is used to select the type of the Auto Iris lens for
use. After this setting, you have to also set the lens type in the
Setup menu (In ALC… and WDR… submenus of IRIS).



DC: When the Auto Iris lens is installed for DC control

signals, set the switch to “DC.”



VIDEO: When the Auto Iris lens is installed for Video

control signals, set the switch to “VIDEO.”

Auto Iris Lens (Optional)

This lens is installed on this camera.

Note

When the camera lens becomes dirty, softly clean it with a lens
tissue or a cloth soaked in pure ethanol.

Rear Panel

❚

AC24/DC12V(SCC-B2315, B2315P)

1

5

2

3

4

AC220V~240V(SCC-B2015P)

1

3

2

10 11

4

ENG

1 Input/Output Connector

This connector has input and output jacks for RS-485 control
signals, Day & Night switching, and alarm output signals.

No

.

Function Description

1 RS-485 DATA+ Jack for connection to RS-485 DATA+

2 RS-485 DATA- Jack for connection to RS-485 DATA-

3 ALARM OUT Alarm out jack for motion detection

4 GROUND Grounding jack.

5 DC +5V Power supply jack for RS-485 JIG. Use

6 EXTERNAL

SENSOR

.

signal line

signal line.

(Open Collector, On Gnd)

within typical DC +5V 100mA

Input jack for Day & Night conversion.
High (DC +3V~+5V): Day mode
Low (0V): Night mode

.

2 Setup Switch

This switch is used to set the function or property. When this
switch is pressed for at least 2 seconds, the Setup menu
appears.



[Left/Right] movement or changing the displayed value:

By pressing this switch left or right, you can move left or
right on the menu or change the displayed value.



[Up/Down] movement: By pressing this switch up or

down, you can move up or down on the menu.



Setting: When you press this switch in the menu, the

selected value or function is confirmed. To enter a
submenu, press this button.

3 Power Display LED

When the power is normally connected, the red LED lights.

4 Video OUT Jack

This is connected to the Video Input jack of the monitor and it
outputs the Video signals.

5 Power Connection Jack

This is connected to the Power cable.

12 13

ENG

Installation

Before Installation

❚

Checking the contents of the package

Make sure that the following items are included in the package.

Camera Camera Holder(Mount)

User's Manual

C Mount Adapter

Auto Iris

Lens Connector

Things to keep in mind during installation and use



Do not disassemble the camera on your own.



Always be careful when handling the camera. Do not

strike the camera by your fists or shake it. Please be
careful not to be careless when storing and operating it.



Do not place or operate the camera in any wet

environment such as rain or wet surfaces.



Do not clean the camera with rough sandpaper. Please

always use a dry cloth when cleaning it.



Put the camera in a cool area free from direct sunlight.

Otherwise, the camera may be damaged.

Connecting the Auto Iris Lens Connector

The Auto Iris Lens Connector that is provided with your camera
consists of the following parts:

Connect each uncovered shutter control cables to the Auto Iris Lens
Connector as the following:

Pin No. DC Control Type Video Control Type

1 Damp(-) Power (+12V)

2 Damp(+) Not applicable

3 Drive(+) Video Signal

4 Drive(-) Ground

14 15

ENG

Installing the Camera

❚

Mounting the lens

When using the CS lens

Mount the CS lens by rotating it clockwise as shown in the picture:

CS lens

When using the C lens

After mounting the C-mount adapter by rotating it clockwise, turn the
C lens clockwise until it is fixed as shown in the picture.

C lens

Setting the ALC lens selection switch

N

You can set the lens selection switch located on the side of the camera
according to the lens type. When the mounted lens is an auto Iris lens
of DC control type, set the switch to “DC.” When the mounted lens is
an auto Iris lens of Video control type, set the switch to “VIDEO.”

Adjusting the back focus

The back focus of the camera is adjusted at the factory before delivery but
some lenses can be out of focus depending on the lens type. In this case,
you have to adjust the back focus. The following describes how to adjust
the back focus of the lenses.

In case of the lens with no zooming function

① After exposing the camera to an object with high resolution (like

a dart-patterned image) at a distance of more than 10m, set the
lens focus ring to infinite (∞).

➁ Adjust the Back Focus Control Bar until the object is of best quality.
➂ Fix the screw of the Back Focus Control Bar.

In case of the lens with zooming function

① After exposing the camera to an object with high resolution (like

a dart-patterned image) at a distance of 3 to 5m, fully rotate the
lens zoom to the TELE direction. Then adjust the lens focus ring
until the object is of best quality.

➁ Fully rotate the lens zoom to the WIDE direction and adjust the

Back Focus Control Bar until the object is of best quality.

➂ Repeat step 1 and 2 two or three times until the focuses of Zoom

TELE and Zoom WIDE are clear enough.

16 17

ENG

Connecting cables and checking operation

N

1. Connect one end of the BNC cable to the VIDEO OUT jack on
the rear of the camera.

2. Connect another end of the BNC cable to the VIDEO IN jack on
the monitor.

Video In Terminal of
Monitor Rear Surface

BNC cable

Video Out Terminal

3. Finally connect the power adapter to the camera. You can

N

connect 2 lines of the power adapter to the camera using the
Slot Head screwdriver as shown in the picture.

(GND: cable with the white stripe line

)

Note

Connect any power source of AC 24V and DC 12V irrespective
of polarity.

18 19

ENG

Camera Setup

This chapter describes how to configure the camera-related settings. If you
press the Setup switch for at least 2 seconds, the Setup menu appears.
The Setup OSD (On-screen Display) map brief is like the following:

ON...

OFF

WDR...

ALC...
ELC...

OFF
AUTO X2 to X256
1/100 (or 1/120) to 1/10K

OFF

LOW
HIGH

NORM

FAST

F.Fast

S.SLOW

SLOW

ON...

OFF

DAY...
NIGHT...
AUTO...

EXT

ATW1

ATW2

AWC

MANU...

OFF

ON...

QUIT
SAVE

PRESET

SETUP

MENU

CAMERA ID

IRIS

SHUTTER

AGC

MOTION

MOTION DET

DAY/NIGHT

WHITE BAL

PRIVACY

SPECIAL ...

RS485 ...

EXIT

❚

CAMERA ID

This CAMERA ID menu is used to assign a camera ID to this
camera. If you press the Setup switch when the CAMERA ID menu
is selected, the corresponding setup screen appears.

CAMERA ID ON...

IRIS ALC...
SHUTTER OFF
AGC HIGH
MOTION DET OFF
DAY/NIGHT DAY...
WHITE BAL ATW2
PRIVACY OFF
SPECIAL ...
RS-485 ...
EXIT QUIT

(CAMERA ID)

ABCDEFGHIJKLMNOPQRSTUVWXYZ

0123456789 : ! - + * ()

RET
SP▶▶ ◀◀SP LOCATION...

CAMERA-1...........

/

You can input a camera ID composed of alphabets, numbers, and
special characters up to 20 characters long. The input camera
ID can be displayed at the desired location when using the
LOCATION… submenu.
When you press the Setup switch in RET, the screen returns to the
upper menu.

❚

IRIS

The IRIS menu is used to set the automatic light control method
for this camera. After setting the ALC Lens Selection Switch

,
select any of DC LENS and VIDEO LENS in the ALC... and WDR...
submenus.

WDR...

If you press the Setup switch when the WDR… submenu is se­lected, the corresponding screen appears.

20 21

ENG

CAMERA ID OFF

IRIS WDR...

SHUTTER OFF
AGC HIGH
MOTION DET OFF
DAY/NIGHT DAY...
WHITE BAL ATW2
PRIVACY OFF
SPECIAL ...
RS-485 ...
EXIT QUIT

(WDR)

TYPE DC LENS

LEVEL1 L � � � I � � � H
LEVEL2 L � � � I � � � H
WHITE BAL INDOOR
RET

First select any of DC LENS, VIDEO LENS, and MANU in TYPE.
You can adjust the shutter speed in LEVEL 1 and the brightness in
LEVEL 2. You can also select any of ALL, OUTDOOR, and INDOOR
in WHITE BAL. In case of ALL, this camera controls both indoor and

outdoor images.

ALC...

If you press the Setup switch when the ALC… submenu is selected,
the corresponding screen appears. First select any of DC LENS and

VIDEO LENS in TYPE.

CAMERA ID OFF

IRIS ALC...

SHUTTER OFF
AGC HIGH
MOTION DET OFF
DAY/NIGHT DAY...
WHITE BAL ATW2
PRIVACY OFF
SPECIAL ...
RS-485 ...
EXIT QUIT

You can

make the BLC (Back Light Compensation) function active
or not. For setting the BLC zone, you can select any of BOTTOM…,
TOP…, LEFT…, RIGHT…, and CENTRE… The actual location is
displayed when you enter each item.
In case of USER…, you can set the desired BLC zone by defining
the size and location. You can set the Video output level in LEVEL.

(ALC)

TYPE DC LENS

BLC OFF
LEVEL ( 0) � � � � I � � � �
RET

Its selectable range is from -9 to +9.

ELC...

If you press the Setup switch when the ELC… submenu is selected,
the corresponding screen appears. You can make the ELC (Elec

-

tronic Light Control) function active or not.

CAMERA ID OFF...

IRIS ELC...

SHUTTER OFF
AGC HIGH
MOTION DET ON...
DAY/NIGHT DAY...
WHITE BAL ATW2
PRIVACY OFF
SPECIAL ...
RS-485 ...
EXIT QUIT

(ELC)

BLC OFF

LEVEL ( 0) � � � � I � � � �
RET

Like the same as the ALC configuration, you can set the BLC zone
and assign the level of the high speed shutter.

SHUTTER

❚

The SHUTTER menu is used to set the high speed electronic
shutter and AUTO low speed shutter.
The high speed electronic shutter can be used 7 different speeds
and is commonly used for imaging fast moving objects.
(NTSC: from 1/100 to 1/10K, PAL: from 1/120 to 1/10K ). The low
speed electronic shutter can be any of 13 speeds from X2 to X256
and it slows the shutter speed to make images clearer in dark
illumination. If you select an AUTO low speed, the shutter speed is
automatically lowered depending on the darkness level.

CAMERA ID OFF
IRIS ALC...

SHUTTER AUTO X4

MOTION SLOW
MOTION DET OFF
DAY/NIGHT DAY...
WHITE BAL ATW2
PRIVACY OFF
SPECIAL ...
RS-485 ...
EXIT QUIT

22 23

ENG

If you keep pressing the LEFT/RIGHT Setup switch, shutter speeds
toggles in the following order:

 OFF  AUTO X2  AUTO X4  AUTO X6  AUTO X8 
AUTO X12  AUTO X16  AUTO X24  AUTO X32  AUTO X48

 AUTO X64  AUTO X96  AUTO X128  AUTO X256  OFF
 1/100 (NTSC), 1/120 (PAL)  1/250  1/500  1/1000  1/2000

 1/4000  1/10K

Note

When the IRIS mode is ELC or WDR, you cannot use high speed
shutters.

AGC

❚

The AGC (Auto Gain Control) menu is used to set the AGC level
of the camera. When the AGC is active, the camera automatically
increases the sensitivity by amplifying the Video signal when the
strength of the signal falls below the normal value.

CAMERA ID OFF
IRIS ALC...
SHUTTER OFF

AGC LOW

MOTION DET OFF
DAY/NIGHT DAY...
WHITE BAL ATW2
PRIVACY OFF
SPECIAL ...
RS-485 ...
EXIT QUIT

Only when OFF or a high speed shutter is selected in the
SHUTTER menu, you can set the AGC level.

You can select any of OFF, LOW, and HIGH.

Note

When the DAY/NIGHT is set to AUTO, the AGC is displayed with

--- so you cannot change its setting.

MOTION

❚

The MOTION menu is used to set the intensity of the camera AGC
level for monitoring motions. This function is available only in AUTO
low speed mode. You can select any of S.SLOW, SLOW, NORM,
FAST, and F.FAST according to the AGC intensity level.

CAMERA ID OFF
IRIS ALC...
SHUTTER AUTO X2

MOTION SLOW

MOTION DET OFF
DAY/NIGHT DAY...
WHITE BAL ATW2
PRIVACY OFF
SPECIAL ...
RS-485 ...
EXIT QUIT

To monitor very fast moving objects in dark illumination, select

F.FAST. To monitor non-moving objects in dark illumination, select
S.SLOW.

MOTION DET

❚

The MOTION DET menu is used to configure the motion detection
related settings. If you press the Setup switch when ON… is selected
in the MOTION DET menu, the corresponding screen appears.

CAMERA ID OFF
IRIS ALC...
SHUTTER OFF
AGC HIGH

MOTION DET ON...

DAY/NIGHT DAY...
WHITE BAL ATW2
PRIVACY OFF
SPECIAL ...
RS-485 ...
EXIT QUIT

(MOTION DET)

TYPE 1

AREA
DISPLAY ON
SENSITIVITY
RET

0 1 2 3

L � � � � I � � H

24 25

ENG

There are 3 different types like 1, 2, and 3. You cannot change the
setting for type 2 because it is prefixed with the full screen. In case of 1
and 3, you can set the motion detection area on your own.

Those 3 types are like the following:

1. Window type: The selected area is displayed with a box. The
motion can be detected for the area only.
You can manually set the motion detection area. You can use the
UP/DOWN/LEFT/RIGHT Setup switch to set the size. To move to
POSITION, press the switch. After setting the position using the
UP/DOWN/LEFT/RIGHT Setup switch, press the Setup switch to
move to the upper menu. To set the size and position for AREA,
select any of 0, 1, 2, and 3.

Window0

Window1

2. Label type: The box-typed motion detection area is prefixed. The
detected area is displayed with size and position changing. You
cannot change AREA because it is displayed with “---.”

Label2

Label1

Label3

Label0

3. Block type: The screen displays with small blocks. When a motion
is detected in the selected blocks, the small blocks are displayed
on the screen.



PRESET: The whole screen becomes the motion

detection area.



USER...: You can manually set the motion detection area.

Use the UP/DOWN/LEFT/RIGHT Setup switch to set the
area. To erase the selected block, press the Setup switch.

In order to set the motion detection area on your own, you have to
specify the size and location for the area setting.
When ON is selected in DISPLAY, the detected motion is displayed
on the screen and the camera sends the Alarm Out signal.
You can also assign the sensitivity for motion detection.

DAY/NIGHT

❚

The DAY/NIGHT menu is used to configure the day and night
related settings for this camera. This camera can turn the IR
(Infrared) filter on or off.

CAMERA ID OFF
IRIS ALC...
SHUTTER OFF
AGC HIGH
MOTION DET OFF

DAY/NIGHT DAY...

WHITE BAL ATW2
PRIVACY OFF
SPECIAL ...
RS-485 ...

26 27

EXIT QUIT

ENG

Note

In case of B/W mode, it may fail to focus when B/W mode is
converted to Color mode.
That is because it must have the condition to have IRIS opened for
the maximum before adjusting the Back-Focus.
The smaller the F number of lens is, the lower the focus depth of
field is (e.g. Using a high speed electronic shutter may lower the
depth of the camera).
It is required to set the focus under the condition that IRIS is open
for the maximum in color mode.

DAY...

If you press the Setup switch when the DAY… submenu is selected,
the corresponding screen appears. You can set the values for
C-GAIN, AGC COLOUR, AGC DETAIL, and C-KNEE in Day mode.
Colour images are implemented by these settings.

(DAY)

C-GAIN (7) � � � � � � I

AGC COLOR ( 0) � � � � I � � � �
AGC DETAIL (7)
C-KNEE (5) � � � � � I � �
RET

I � � � � � � �

Note

When the value of AGC DETAIL becomes large, it also makes the
noise stand out.

NIGHT...

If you press the Setup switch when the NIGHT… submenu is se­lected, the corresponding screen appears.

(NIGHT)

COLOR/BW COLOR...
RET

Even in night mode, you can see colour images in bright illumina­tion. Therefore you can select any of COLOUR… and BW… In case
of COLOUR…, you have to set the colour temperature for white
balance. You can also specify the settings for red and blue colours
on your own.

In case of BW..., when the BURST is set to ON, the burst
signals are output with the BW Composite Video signals. And no burst
signals are output when the BURST is set to OFF.

AUTO...

This automatically converts the DAY mode to NIGHT mode and vice
versa depending on illumination. In low illumination, it removes the IR
filtering function to raise the sensitivity. Otherwise, it activates the IR
filtering function to lower the sensitivity.
If you press the Setup switch when the AUTO… submenu is
selected, the corresponding screen appears.

(AUTO)

LEVEL ( 0) I � � � � � � � �

DAY

 NIGHT 2 S

NIGHT  DAY 5 S

28 29

RET

ENG

For this function, you can specify the level for each conversion
between Day and Night.

Note

When the DAY/NIGHT is set to AUTO, the AGC is displayed with

--- so you cannot change its setting.

EXT

This automatically converts the colour mode to BW mode and vice
versa by interfacing with an external sensor.

CAMERA ID OFF
IRIS ALC...
SHUTTER OFF
AGC HIGH
MOTION DET OFF

DAY/NIGHT EXT

WHITE BAL ATW2
PRIVACY OFF
SPECIAL ...
RS-485 ...
EXIT QUIT

WHITE BAL

❚

The WHITE BAL menu is used to configure the white balance
related settings for this camera.

CAMERA ID OFF
IRIS ALC...
SHUTTER OFF
AGC HIGH
MOTION DET OFF
DAY/NIGHT DAY...

WHITE BAL ATW1

PRIVACY OFF
SPECIAL ...
RS-485 ...
EXIT QUIT

To adjust the white balance, 4 different modes are provided as follows:



ATW1

(Auto Tracing White Balance mode 1): The camera can
automatically adjust the colour temperature in real time according
to the ambient temperature change. The colour temperature
variation range is approximately from 2500°K to 9300°K.



ATW2: Its colour temperature variation range is

approximately from 2000°K to 10000°K.



AWC

(Auto White Balance Control): The colour temperature
setting is made once. After selecting this, expose to an object
to memorize the colour temperature of it and press the
switch. The fixed colour temperature is applied.



MANU…: You can manually set the current colour

temperature. You can also specify the settings for red and

Setup

blue colours on your own.

PRIVACY

❚

The PRIVACY menu is used to configure the privacy related settings
for this camera. If you press the Setup switch when ON… is selected
in the PRIVACY menu, the corresponding screen appears.

CAMERA ID OFF
IRIS ALC...
SHUTTER OFF
AGC HIGH
MOTION DET OFF
DAY/NIGHT DAY...
WHITE BAL ATW2

PRIVACY ON...

SPECIAL ...
RS-485 ...
EXIT QUIT

You can set 24 privacy zones in total. For configuration for 0 to 15 zones,
you have to set the size, location, and colour. In case of configuration for

PRIVACY(1/2)

0 1 2 3 4 5
6 7 8 9 10 11
12 13 14 15

MOSAIC 4

RET

PRIVACY(2/2)

16 17 18 19 20 21
22 23

MOSAIC OFF

RET

15 to 23 zones, you have to additionally set the type.

30 31

ENG

PRIVACY 0

PRIVACY 16

< SIZE >

< LOCATION >

COLOR ...
EXIT QUIT

<In case of selecting a zone on first page>

In case of type1, a box type zone is set while a diamond type zone is
set for the type 2. When the privacy is any from 0 to 15, four different
sizes of mosaics are provided. When the privacy is any from 16 to 23,
you cannot change the size of the mosaic because it is already prefixed.

< SIZE >

< LOCATION >

TYPE 1
COLOR ...
EXIT QUIT

<In case selecting a zone on second page>

For 16 to 23 privacies, you cannot set the colour of the mosaic.

SPECIAL

❚

The SPECIAL menu is used to configure the special settings for this
camera. If you press the Setup switch when … is selected in the
SPECIAL menu, the corresponding screen appears.

CAMERA ID OFF
IRIS ALC...
SHUTTER OFF
AGC HIGH
MOTION DET OFF
DAY/NIGHT DAY...
WHITE BAL ATW2
PRIVACY OFF

SPECIAL ...

RS-485 ...
EXIT QUIT

(SPECIAL)

LANGUAGE ENGLISH

V-SYNC INT
DIGITAL ZOOM OFF
VIDEO SET ...
DNR OFF
FLICKERLESS OFF
SYSTEM INFO ...
RET

LANGUAGE

You can change the OSD language using the LEFT/RIGHT Setup switch.

V-SYNC

You can select a vertical synchronization mode between INT and
LINE. In case of INT, the camera uses the inside crystal

oscillator for synchronization. In case of LINE, the camera uses the
frequency of the external power for synchronization.

Note

In case of LINE, it doesn’t support DC 12V, for which “---” is displayed.

DIGITAL ZOOM

You can set the level and ratio of digital zoom. If you press the Setup
switch when ON… is selected in DIGITAL ZOOM, the
corresponding screen appears.

(SPECIAL)

LANGUAGE ENGLISH
V-SYNC INT

DIGITAL ZOOM ON...

VIDEO SET ...
DNR OFF
FLICKERLESS OFF
SYSTEM INFO ...
RET

The first displayed number means the zoom
displayed number is the magnification. When the level reaches 130,
the magnification becomes 2. After the zooming position is selected,

(DIGITAL ZOOM)

RATIO (000) I � � � � (X01)

< LOCATION >
RET

ratio

and the second

the digital zoom function applies.

VIDEO SET

You can configure the Video output related settings. If you press the
Setup switch when … is selected in VIDEO SET, the corresponding
screen appears.

(SPECIAL)

LANGUAGE ENGLISH
V-SYNC INT
DIGITAL ZOOM OFF

VIDEO SET ...

DNR OFF
FLICKERLESS OFF
SYSTEM INFO ...
RET

You can set the values for REVERSE, DETAIL, Y-LEVEL, C-LEVEL,
and POSI/NEGA.
In case of REVERSE, the camera provides 3 different reversion

(VIDEO SET)

REVERSE OFF

DETAIL ( 2) � � I �
Y-LEVEL ( 0)
C-LEVEL ( 0) I � � � � � � � �
POSI/NEGA +
RET

I � � � � � � � �

modes: horizontal (H), vertical (V), and both (H/V).

32 33

ENG

DNR

You can configure the DNR (Digital Noise Reduction) related set­tings. If you press the Setup switch when ON… is selected in DNR,
the corresponding screen appears.

(SPECIAL)

LANGUAGE ENGLISH
V-SYNC INT
DIGITAL ZOOM
VIDEO SET ...

DNR ON...

FLICKERLESS OFF
SYSTEM INFO ...
RET

OFF

(DNR)

LEVEL L � � � � I � � � � H

RET

You can set the level for this configuration.

FLICKERLESS

When this is set to ON, the shutter speed is set to 1/100 sec (for
NTSC) or 1/120 sec (for PAL) to prevent from flickering by the disac
cordance between vertical synchronization frequency and on-and-off
frequency of the light.

-

SYSTEM INFO

You can check the system-related information. If you press the Setup
switch when … is selected in SYSTEM INFO, the corresponding
screen appears.

(SPECIAL)

LANGUAGE ENGLISH
V-SYNC INT
DIGITAL ZOOM
VIDEO SET ...
DNR OFF
FLICKERLESS OFF

SYSTEM INFO ...

RET

OFF

(SYSTEM INFO)

ROM VER 1.000
EEP VER 1.000
PROTOCOL SAMSUNG
ADDRESS 0
TYPE RS-485, HALF
BAUD RATE 9600

SERIAL NO.

RET

0000000000000

You can find the system information about ROM version, EEP
version, protocol, address, type, baudrate, and serial number.

RS-485

❚

The RS-485 menu is used to configure the RS-485 communication
related settings for this camera. You can connect to RS-485 through the
rear panel.

34 35

ENG

If you press the Setup switch when … is selected in the RS-485 menu,
the corresponding screen appears.

(RS-485)

PROTOCOL SAMSUNG

BAUD RATE 9600
ADDRESS 0

RET

You can set the protocol, baudrate, and address (range: 0 to 255) for

this communication

EXIT

❚

The EXIT menu is used to exit from the SETUP menu. You can
select the following options:



QUIT: Ignores the change and returns to the previous

settings.



SAVE: Saves the change.



PRESET: Ignores the change and returns to the factory

default settings.

CAMERA ID OFF
IRIS ALC...
SHUTTER OFF
AGC HIGH
MOTION DET OFF
DAY/NIGHT DAY...
WHITE BAL ATW2
PRIVACY OFF
SPECIAL ...
RS-485 ...

EXIT QUIT

Product Specifications

Item Details

Product type CCTV Camera (WDR & DAY/NIGHT)

Power source

Broadcast type

Power
consumption

Image device 1/3” P/S Super-HAD CCD

Effective pixels NTSC: 768(H) x 494(V) / PAL: 752(H) x 582(V)

Scanning mode

Scanning line
frequency

Synchronization mode

Resolution 540/570 TV Lines (COLOUR/BW)

S/N Ratio Approx. 50dB

Min. Scene
Illumination

36 37

SCC-B2315: AC 24V ± 10% (60Hz ± 0.3 Hz),

DC 12V +10%/-5%

SCC-B2315P: AC 24V ± 10% (50Hz ± 0.3 Hz),

DC 12V +10%/-5%

SCC-B2015P: AC 220 to 240V ± 10% (50Hz ± 0.3 Hz)

SCC-B2315P, B2015P: PAL Standard Colour System
SCC-B2315: NTSC Standard Colour System

SCC-B2315(P): Approx. 4W
SCC-B2015P: Approx. 4.5W

NTSC: 525 Lines, 2:1 Interlace / PAL: 625 Lines, 2:1 Interlace

Horizontal: NTSC 15,734Hz(INT)/15,750Hz(LL)
PAL 15,625Hz(INT)/15,625Hz(LL)
Vertical: NTSC 59.94Hz(INT)/60Hz(LL)
PAL 50Hz(INT)/50Hz(LL)

INT/Line Lock

0.40 Lux(F1.2, 50 IRE)

0.24 Lux(F1.2, 30 IRE)

0.12 Lux(F1.2, 15 IRE)

0.04 Lux(F1.2, 50 IRE)

0.024 Lux(F1.2, 30 IRE)

0.012 Lux(F1.2, 15 IRE)

Colour Lux

B/W Lux

Sens-Up Off

Sens-Up x256 0.0005 Lux(F1.2, 15 IRE)

Sens-Up Off

Sens-Up x256 0.00005 Lux(F1.2, 15 IRE)

ENG

Item Details

Dynamic Range

IRIS WDR/ALC/ELC

Electronic shutter
speed

AGC OFF/LOW/HIGH

Motion F.FAST/FAST/NORM/SLOW/S.SLOW

Motion Detection

Day/Night DAY/NIGHT/AUTO/EXT

White Balance ATW1/ATW2/AWC/MANUAL Mode

Privacy ON/OFF

Signal output Composite Video (1.0 Vp-p, 75ohm, BNC)

AI lens

Lens mount CS/C (Mount Adaptor)

Operation
temperature

Operation
humidity

Size 65(W) x 55(H) x 130.5(D)mm

Weight

NTSC: x128 / PAL: x160

High Speed: OFF~1/10K sec
Low Speed: OFF~X256

ON/OFF

(3200°K, 5600°K, R/B Gain adjustment)

VIDEO/DC

-10°C~+50°C

~90%

SCC-B2315(P): Approx. 410g
SCC-B2015P: Approx. 600g

Memo

38 39

ENG

Memo

Correct Disposal of This Product

(Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with

separate collection systems)
This marking shown on the product or its literature, indicates that it

should not be disposed with other household wastes at the end of its
working life. To prevent possible harm to the environment or human
health from uncontrolled waste disposal, please separate this from other
types of wastes and recycle it responsibly to promote the sustainable
reuse of material resources.

Household users should contact either the retailer where they purchased
this product, or their local government office, for details of where and how
they can take this item for environmentally safe recycling.

Business users should contact their supplier and check the terms and
conditions of the purchase contract. This product should not be mixed
with other commercial wastes for disposal.