Samsung SCC-B1331BP, SCC-B1031BP, SCC-B1031P, SCC-B1331 User Manual

SCC-B1331(P)

SCC-B1031P

DIGITAL COLOR CAMERA

user manual

ENG

FRE

GER

SPA

ITA

imagine the possibilities

Thank you for purchasing this Samsung product. To receive more complete service,

please register your product at

www.samsungsecurity.com

Safety information

CAUTION

RISK OF ELECTRIC SHOCK.

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE REAR COVER. NO USER SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL..

This symbol indicates high voltage is present inside. It is dangerous to make any kind of contact with any inside part of this product.

This symbol alerts you that important literature concerning operation and maintenance has been included with this product.

WARNING

•To prevent damage which may result in fire or electric shock hazard, do not expose this appliance to rain or moisture.

WARNING

1.Be sure to use only the standard adapter that is specified in the specification sheet. Using any other adapter could cause fire, electrical shock, or damage to the product

2.Incorrectly connecting the power supply or replacing battery may cause explosion, fire, electric shock, or damage to the product.

3.Do not connect multiple cameras to a single adapter. Exceeding the capacity may cause abnormal heat generation or fire.

4.Securely plug the power cord into the power receptacle. Insecure connection may cause fire.

5.When installing the camera, fasten it securely and firmly. A falling camera may cause personal injury.

6.Do not place conductive objects (e.g. screwdrivers, coins, metal things, etc.) or containers filled with water on top of the camera. Doing so may cause personal injury due to fire, electric shock, or falling objects.

7.Do not install the unit in humid, dusty, or sooty locations. Doing so may cause fire or electric shock.

8.If any unusual smells or smoke come from the unit, stop using the product. In such case, immediately disconnect the power source and contact the service center. Continued use in such a condition may cause fire or electric shock.

9.If this product fails to operate normally, contact the nearest service center. Never disassemble or modify this product in any way. (SAMSUNG is not liable for problems caused by unauthorized modifications or attempted repair.)

2 – DIGITAL COLOR CAMERA

Safety information

10.When cleaning, do not spray water directly onto parts of the product. Doing so may cause fire or electric shock.

CAUTION

	1.	Do not drop objects on the product or apply strong shock to it. Keep away from a location
		subject to excessive vibrationor magnetic interference.
	2.	Do not install in a location subject to high temperature (over 50°C), low temperature (below -
		10°C), or high humidity. Doing so may cause fire or electric shock.
	3.	If you want to relocate the already installed product, be sure to turn off the power and then move
		or reinstall it.
	4.	Remove the power plug from the outlet when then there is a lightning. Neglecting to do so may
		cause fire or damage to the product.
	5.	Keep out of direct sunlight and heat radiation sources. It may cause fire.
	6.	Install it in a place with good ventilation.
	7.	Avoid aiming the camera directly towards extremely bright objects such as sun, as this may
		damage the CCD image sensor.	ENG
	8.	Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as
		vases, shall be placed on the apparatus.
	9.	The Mains plug is used as a disconnect device and shall stay readily operable at any time.

English – 3

Important Safety Instructions

1.Read these instructions.

2.Keep these instructions.

3.Heed all warnings.

4.Follow all instructions.

5.Do not use this apparatus near water.

6.Clean only with dry cloth.

7.Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8.Do not install near any heat sources such as radiators, heat registers, or other apparatus (including amplifiers) that produce heat.

9.Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10.Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11.Only use attachments/accessories specified by the manufacturer.

12.Use only with cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus.

13.Unplug this apparatus when a card is used. Use caution when moving the cart/ apparatus combination to avoid injury from tip-over.

14.Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as powersupply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

4 – DIGITAL COLOR CAMERA

Contents

Introduction

Features		6
PRODUCT & ACCESSORIES		7
Part Names and Functions		8

Installation

Connecting the Auto Iris Lens Connector		11
Mounting the lens		11
Connecting cables and checking operation		12

How to use OSD Menu
Using Icons in the Menu	13
Main Menu	13
Profile	14
Camera Setup	16
Intelligence	21	ENG
Privacy zone Setup	22
Other Set	23
System Information	23
Language	23
Specifications
Specifications	25

English – 5

Introduction

FEATURES

High Resolution

•This camera has realized high resolution of 600 lines using the top-notch full digital image processing and special algorithm technologies.

Intelligent Motion Detection & Tracking

•This is an intelligent function that automatically detects a motion of an object. You can set a virtual fence so it sounds an alert if an object passes / enters /exits the virtual fence or virtual area.

XDR (eXtended Dynamic Range)

•Actively controls the gamma compensation in the way it operates the ambient luminance contrast in a certain pixel unit to determine the optimal visibility.

DAY/NIGHT

•This function can make the IR Cut filtering function inactive under the illumination below the normal value.

High Sensitivity

•It implements images of high sensitivity using the up-to-date SONY Super-HAD Progressive CCD.

Low Illumination

•It uses the digital signal technologies such as low illumination and Day/Night functions that make your camera identify objects even in the worst environment.

Superior Backlight Adjustment

•When an object has a bright illumination or sunlight behind it, this camera automatically improves the shaded object picture quality.

Digital Power Synchronization

•The full digital Line Lock function directly adjusts the vertical camera synchronization to enhance the operationability and reliability of this camera.

Output Signal Setting

•You can set the following Video output signals: Image reversion (Horizontal, Vertical, or both), Privacy, Horizontal/Vertical profiling, and digital zooming.

OSD(On Screen Display) Menu

•OSD menu is provided to display the status of camera and to configure the functions interactively.

6 – DIGITAL COLOR CAMERA

Introduction

PRODUCT & ACCESSORIES

Product & Accessories

• Main Product

Camera	ENG

• Accessories

Camera Holder(Mount)	C Mount Adapter	User’s Manual	Auto Iris
			Lens Connector

English – 7

Introduction

PART NAMES AND FUNCTIONS

Side View

Mount Adapter

Fixing Grooves

	Auto Iris Lens	Camera Lens
	Connector

Auto Iris Lens

Control Cable

• Auto Iris Lens Connector

This groove is used for screwing the mount adapter, a part of the bracket where the camera will be installed.

•Auto Iris Lens Control Cable

This cable transmits the power and signals from the camera for controlling the Auto Iris Lens.

•Mount Adapter Fixing Grooves

These grooves are used when fixing screws of the mount adapter connected to the bracket when installing the camera on it.

Note :

–When the camera lens becomes dirty, softly clean it with a lens tissue or a cloth soaked in pure ethanol.

8 – DIGITAL COLOR CAMERA

Introduction

Rear Panel

	<AC24/DC12V (SCC-B1331(P))>
n	o

p	q
r
	s	ENG
	<AC220V~240V(SCC-B1031P)>

n	o
	p

s	q

English – 9

Introduction

n Input/Output Connector

This connector has input and output ports for and alarm output signals.

No.								Function	Description
1							ALARM OUT		Alarm out port for motion detection. (Open collector type)
2								GND	Grounding Port.
3							TRIGGER IN		Displays the current still image when it receives the Trigger signal.
									(Normal Open Type)
4							SHUTTER (S0)		This is a port for selecting an external high speed shutter mode.
									If connected in LOW (0V), it will become ON inside.
5							SHUTTER (S1)		This is a port for selecting an external high speed shutter mode.
									If connected in LOW (0V), it will become ON inside.
6							SHUTTER (S2)		This is a port for selecting an external high speed shutter mode.
									If connected in LOW (0V), it will become ON inside.
7								5V OUT	Power supply port for RS-485 JIG. Use within typical DC +5V 100mA

o SETUP Switch

This switch is used to set the function or property. When this switch is pressed for at least 2 seconds, the MAIN MENU appears.

ef(Left/Right) : By pressing this switch left or right, you can move left or right on the menu or change the displayed value.

cd(Up/Down) : By pressing this switch up or down, you can move up or down on the menu.

: When you press this switch in the menu, the selected function is confirmed. To enter a submenu, press this button.

pPower Display LED

When the power is normally connected, the red LED lights.

qVideo OUT Port

This is connected to the Video Input Port of the monitor and it outputs the Video signals.

rGND

This is a grounding port.

sPower Connection Port

This is connected to the Power cable.

10 – DIGITAL COLOR CAMERA

	Installation
CONNECTING THE AUTO IRIS LENS	MOUNTING THE LENS
CONNECTOR
	When using the CS lens
	Mount the CS lens by rotating it clockwise as shown
	in the picture:
	CS lens
	CS

Connect each uncovered shutter control cables to the Auto Iris Lens Connector as the following

	Pin	DC Control	Video Control Type
	No.	Type
	1	Damp(-)	Power (+12V)
	2	Damp(+)	Not applicable
	3	Drive(+)	Video Signal
	4	Drive(-)	Ground

Note :

–You can switch a control type of the lens in the menu.

ENG When using the C lens

After mounting the C-mount adapter by rotating it clockwise, turn the C lens clockwise until it is fixed as shown in the picture.

CClens

English – 11

Installation

CONNECTING CABLES AND CHECKING OPERATION

Connect one end of the BNC cable to the VIDEO OUT Port on the rear of the camera.

Connect another end of the BNC cable to the VIDEO IN Port on the monitor.

Finally connect the power adapter to the camera. You can connect 2 lines of the power adapter to the camera using the Slot Head screwdriver as shown in the picture.

(GND: cable with the white stripe line)

1.
32..ATGRLNIADRAM OUT 5.
4.	GGERIN 6.
	SHUTTER(SO) 87..

1	2	3	4	5
					6

SS5DVHHAUUYOTT/NUTTITEEGHRR((SST12IN))

7

8

Video In Terminal of Monitor Rear

Surface

BNC cable

Video Out Terminal

Note :

– Connect any power source of AC 24V and DC 12V irrespective of polarity.

12 – DIGITAL COLOR CAMERA

How to use OSD Menu

USING ICONS IN THE MENU

• (EXIT)

Exits the menu setting.

Before you exits the menu setting, select SAVE to save your settings, or select QUIT to cancel.

• (RET)

Returns to the previous menu.

• (HOME)

Returns to the main menu.

• (SAVE)

Used to save your settings of MASK AREA, PRIVACY ZONE and more.

Once you save your settings, they will remain even if you select QUIT in the menu.

• (DEL)

Used to deletes your settings of MASK AREA, PRIVACY ZONE and more.

Once you delete your settings, they will not be restored even if you select QUIT in the menu.

MAIN MENU

ÃÃMAIN MENUÃÃ

PROFILE

CAMERA SET INTELLIGENCE PRIVACY ZONE OTHER SET SYSTEM INFO LANGUAGE

• PROFILE

You can set a mode according to the camera installation conditions.

• CAMERA SET

Configure Camera related functions and data.	ENG
• INTELLIGENCE
You can configure the settings of motion
detection,tracking and more.

• PRIVACY ZONE

You can configure the privacy related settings.

• OTHER SET

You can configure for Factory Defaults, and more.

• SYSTEM INFO.

Displays the system information including the camera version and communication settings.

• LANGUAGE

Select a preferred one from the supported languages.

English – 13

How to use OSD Menu

PROFILE

ePROFILEf

ÃSTANDARD

ITS

BACKLIGHT

GAMING

CUSTOM

In the PROFILE menu, you can configure the following camera settings at once.

CAMERA SET Menu
Previous	Sub-menus	STANDARD	ITS	BACKLIGHT	GAMING
Menu
IRIS		ALC	ALC	ALC	ALC
	ALC	-	-	-	-
	LENS	DC	DC	DC	DC
	LEVEL	0	0	0	0
	BACKLIGHT	OFF	OFF	WDR	OFF
	WEIGHT	User setting	User setting	MID	User setting
		allowed	allowed		allowed
	WHITE BAL	User setting	User setting	User setting	User setting
		allowed	allowed	allowed	allowed
MOTION		(F.FAST)---	(F.FAST)---	NORM	SLOW
DNR		MID	MID	MID	MID
SHUTTER		OFF	AUTO1/250	OFF	OFF
SENS-UP		AUTOx4	AUTOx2	AUTOx4	AUTOx4
XDR		MID	MID	MID	MID

14 – DIGITAL COLOR CAMERA

How to use OSD Menu

CAMERA SET Menu
Previous	Sub-menus	STANDARD	ITS	BACKLIGHT	GAMING
Menu
WHITE BAL		DAY	DAY/NIGHT	DAY	DAY
	DAY	-	-	-	-
	MODE	ATW2	ATW1	ATW1	ATW1
	RED	0	0	0	0
	BLUE	0	0	0	0
DETAIL		2	2	2	2

ENG

ITS

It will be set automatically so you can easily check the traffic conditions.

BACKLIGHT

It will be set automatically so you can distinguish the object from the background in a severe backlighting scene.

GAMING

It will be set automatically to help you take a picture in a regular indoor lighting condition.

English – 15

How to use OSD Menu

CAMERA SETUP

eCAMERA SETf

CAMERA ID				OFF
IRIS				ALC
MOTION		(F.FAST)---
DNR				MID
SHUTTER				OFF
SENS-UP			AUTO X4
FLICKERLESS			(OFF)---
XDR				MID
DIS					OFF
		d
		c
			AUTO
DAY/NIGHT
WHITE BAL
DIGITAL ZOOM				OFF
DETAIL			[2]
V-SYNC				INT
AGC COLOR SUP				LOW
REVERSE				OFF
POSI/NEGA			+
PIP				OFF

Setup the general functions of zoom camera module. Use the cdefswitch to select a menu item.

CAMERA ID		[OFF, ON]
		CAMERA ID
	ABCDEFGHIJKLMNOPQRSTUVWXYZ0
123456789 :?-+*()/

SPffeeSP LOCATION

CAMERA-1..................

...........................

The CAMERA ID menu is used for you to assign a unique name to a camera. If you press the SETUP switch with the CAMERA ID menu selected, you will see the appropriate screen.

You can enter up to 54 alphanumeric or special characters for the CAMERA ID. Select LOCATION and press the SETUP switch to move the display position of the CAMERA ID.

IRIS	[ALC, ELC]

The IRIS menu is used if you want to adjust the intensity of radiation incoming to the camera.

•ALC (Automatic Light Control)

If you press the SETUP switch with an ALCbased sub menu selected, you will see the appropriate screen.

		ALC
LENS		DC
LEVEL		[00]----I----
BACKLIGHT		OFF

The LENS menu is used if you select a type of the AI lens.

For normal operation, you must select DC for a DC-type lens, and select VIDEO for a VIDEOtype lens.

16 – DIGITAL COLOR CAMERA

How to use OSD Menu

The LEVEL menu is used to adjust the

overall brightness, where “+” will increase the brightness and “–” will decrease it.

If you set the BACKLIGHT option to BLC, you will see a menu where you can set the BLC area.

you can set the desired BLC zone by defining the size and location.

LENS			ALC		DC
LEVEL				[00]----I	----
	BACKLIGHT				BLC
	AREA				USER
	<SIZE>
	<LOCATION>

If you use an ordinary camera in a scene with an intensive backlight, the object will be displayed dark on the monitor affected by the backlight. To solve this problem, you can use the BLC(Back Light Compensation) function to improve the sharpness of the image in such a high contrast scene.

Namely, it improves the sharpness of the picture in outdoor scenery as well as indoor.

•ELC (Electronic Light Control)

If you press the SETUP switch when the ELC submenu is selected, the corresponding screen appears. You can make the ELC (Electronic Light Control) function active or not.

	ELC
LEVEL	[00]----I----
BACKLIGHT		OFF

In similar to ALC setting, you can specify the BLC area.

	ELC
LEVEL		[00]----I----
BACKLIGHT			BLC
AREA		USER
<SIZE>

<LOCATION>

AGC
[OFF, VERY LOW, LOW, MID, HIGH, VERY
HIGH, USER, FIX]
The AGC (Auto Gain Control) menu is used to	ENG
set the AGC level of the camera. When the AGC
is active, the camera automatically increases the
sensitivity by amplifying the Video signal when
the strength of the signal falls below the normal
value.
If OFF or FIX mode is selected in the SENS-UP
menu, you can specify the AGC level.
If you press the SETUP switch with a USER
sub menu selected, you will see the appropriate
screen.

AGC USER

LEVEL [16]

In USER mode, you can break down the level in 16 steps from VERY LOW to VERY HIGH to your preference.

English – 17

How to use OSD Menu

AGC FIX

LEVEL [01]

If you press the SETUP switch with a FIX sub menu selected, you will see the appropriate screen.

As a fixed value of the AGC gain is used in FIX mode, you can select one of the 16 detailed levels from VERY LOW to VERY HIGH before fixing it.

DNR	[OFF,LOW,MID,HIGH, USER(1~16)]

You can configure the DNR (Digital Noise Reduction) related settings.

Reduces the noise on the screen.

This is especially useful for a severely distorted screen.

You can set the level if you set DNR to USER.

SHUTTER

[OFF, AUTO 1/100(PAL:1/120), AUTO 1/250, AUTO 1/500, AUTO 1/1000, AUTO 1/2000, AUTO 1/4000, AUTO 1/10K , 1/100(PAL:1/120), 1/250, 1/500, 1/1000, 1/2000, 1/4000, 1/10K , EXT]

The SHUTTER menu is used to set the fixed high-speed electronic shutter, auto high speed electronic shutter and external high speed electronic shutter(EXT).

You can select one of 7 options from 1/100(PAL:1/120) to 1/10K for the fixed high speed electronic shutter, which is mostly used for imaging a fast moving object.

The auto high speed electronic shutter operates as the fixed high speed shutter in a high contrast scene but automatically focuses the target if the iris opens fully in a low contrast scene like in ELC mode. When it gets brighter back, the mode will switch to the fixed high speed electronic shutter mode.

However, the auto high speed shutter operates properly only in a camera featuring a DC or VIDEO

lens.

In external high speed electronic shutter (EXT) mode, you can select one of 8 modes from OFF through 1/100(PAL:1/120) to 1/10K for the high speed electronic shutter. It works as the high speed electronic shutter. You can select an option using SHUTTER(S0), SHUTTER(S1) and SHUTTER(S2) on the rear.

Connect each of the terminals to GND.

See the below table for the operation.

SHUTTER(S0) SHUTTER(S1) SHUTTER(S2)

	OFF
	(NTSC: 1/60,	OFF	OFF	OFF
	PAL:1/50)
	1/100	ON	OFF	OFF
	(PAL:1/120)
	1/250	OFF	ON	OFF
	1/500	ON	ON	OFF
	1/1000	OFF	OFF	ON
	1/2000	ON	OFF	ON
	1/4000	OFF	ON	ON
	1/10K	ON	ON	ON

Note :

–If the SHUTTER option is set to fixed electronic shutter or EXT mode, the SENS-UP menu will be deactivated.

FLICKERLESS

[OFF, ON]

If set to ON, the shutter speed will be fixed to 1/100(PAL:1/120) second. This will prevent possible screen distortion due to a mismatch between the vertical sync frequency and the blinking frequency of the lighting.

XDR (eXtended Dynamic Range) [OFF, LOW, MID, HIGH]

Actively controls the gamma compensation in the way it operates the ambient luminance contrast in a certain pixel unit to determine the optimal visibility.

18 – DIGITAL COLOR CAMERA

How to use OSD Menu

WHITE BAL

[DAY/NIGHT]

If you want to adjust the color scheme, use the

WHITE BALANCE function.

• DAY

In DAY mode, you can set the color values of RED and BLUE. The screen will be displayed in colors according to your settings.

WHITE BAL

DAY/NIGHT					DAY
MODE				AWC
RED		[00]----I----
BLUE		[00]----I----
R-GAIN			[0248]
B-GAIN			[0247]

Note :

–You can set the values of R-GAIN and B-GAIN only in AWC mode.

•NIGHT

Use the NIGHT mode if you want to set the white balance differently according to the ambient luminance.

If the NIGHT mode is set to OFF, the white balance will always operate as set in DAY mode; if not to OFF, the camera will switch to as set in DAY/NIGHT mode according to the brightness.

In NIGHT mode, you can set the values of RED, BLUE and BRIGHTNESS. The screen will be displayed in colors according to your settings.

	WHITE BAL
DAY/NIGHT			NIGHT
BRIGHTNESS				MID
MODE			AWC
RED		[00]----I----
BLUE		[00]----I----
R-GAIN		[0248]
B-GAIN		[0247]

Note :
– You can set the values of R-GAIN and B-GAIN only in
AWC mode.
– If AGC is set to OFF or FIX, you can not access the
NIGHT menu.
– For adjusting the white balance, the following
5 modes are provided:
• ATW1(Auto Tracing White Balance mode	ENG
1): The camera can automatically adjust the
color temperature in real time, according to
the ambient conditions. The color temperature
ranges from approx. 2500K to 9300K.
• ATW2: The color temperature ranges from
approx. 2,000K to 10,000K.
• AWC ( Auto White Balance Control): If you
press the SETUP switch in the appropriate item
position, Auto White Balance will perform once.
• 3200K : Set color temperature to 3200K
• 5600K : Set color temperature to 5600K
– RED : Adjusts the strength of the red color.
– BLUE : Adjusts the strength of the blue color.
– R-GAIN/B-GAIN : Enables you to set the current
color temperature manually.
– BRIGHTNESS : Select a brightness level in
switching from setting in DAY mode to setting in
NIGHT mode.

–

English – 19

How to use OSD Menu

DIGITAL ZOOM

[ON/OFF]

You can set the digital zoom factor and position. If you press the SETUP switch with the DIGITAL ZOOM function set to ON, you will see the appropriate screen.

When the zoom factor and position are defined, the digital zoom function will operate.

DIGITAL ZOOM

RATIO		[X1.0]
< LOCATION >

-LOCATION : If you press the SETUP switch in the condition where the image is enlarged as much as the

ratio setting, you can watch an invisible area of the effective screen as well using the cdefswitch.

Note :

–If the digital zoom factor is set to larger than 1x, the FENCE function will be deactivated.

The DIGITAL ZOOM function enlarges the pixel itself, which can cause deterioration of the quality.

DETAIL [0~3]

Controls the horizontal or vertical distinction.

V-SYNC

[INT, LINE]

Select the vertical sync mode for INT or LINE.

If you select INT, the camera will use the internal synchronization.

If selecting LINE, the camera will use the external power source frequency for the synchronization.

You can adjust the LL-PHASE.

Note :

–Use of DC 12V will fix V-SYNC to INT, which can not be changed.

AGC COLOR SUP

[LOW , MID, HIGH]

Adjust the color scheme according to the AGC value.

REVERSE

[OFF, H, V, H/V]

Mirrors video signals horizontally, vertically, or both.

POSI/NEGA

[+, -]

Output as it is or mirror the video brightness signal.

PIP

[OFF, ON]

Displays a sub image together with the main image on the same screen using the Picture In Picture function.

Note :

–If more than one privacy zone is set and the PRIVACY SET is set to ON, the PIP function will be deactivated.

–If the INTELLIGENCE function is set to FENCE mode, the PIP menu will be deactivated.

DIS

[OFF, ON]

Digital Image Stabilization will set the anti-shake compensation.

Note :

–If you set DIS to ON, the compensation area will be enlarged as set in the digital zoom factor.

If you set the digital zoom factor to greater than the enlarged zoom factor for the compensation, the DIS function will be deactivated.

20 – DIGITAL COLOR CAMERA

How to use OSD Menu

INTELLIGENCE

eINTELLIGENCEf

MOTION			OFF
MASK AREA	1 2 3 4
DISPLAY			ON
SENSITIVITY	[4]
RESOLUTION	[5]
ALARM OUT

You can set the motion detection and tracking in the

INTELLIGENCE menu.

MOTION

[OFF,TRACKING,DETECTION]

•TRACKING

Detects and tracks a moving object.

•DETECTION

Detects a moving object.

MASK AREA [1~4]

Specify a detection exception area to mask.

Select a mask number and specify the size and position.

-MASK AREA

<SIZE> <LOCATION>

DISPLAY [ON, OFF]

With the DISPLAY option set to ON, a motion or a set ADVANCED function will be displayed on the screen, if detected.

SENSITIVITY

[1~7]

Set the sensitivity of the motion detection.

RESOLUTION

[1~5]

If setting it to high, the camera can detect even a trivial movement of the target.

ALARM OUT

If you set a desired menu item to ON, the camera will sound an alert if it detect the appropriate motion.

ALARM OUT

MOTION

ON

			ENG

s

English – 21

How to use OSD Menu

PRIVACY ZONE SETUP

		ePRIVACY ZONEf
1	2		3	4	5	6
7	8		9	10	11	12
PRIVACY SET						ON
STYLE					MOSAIC1

The PRIVACY function will protect your privacy by screening the privacy area that you have specified during monitoring. You can specify up to 12 privacy zones.

If you set the PRIVACY SET to ON, your PRIVACY ZONE settings will be applied.

You can change the style to adjust the mosaic size and color of the PRIVACY ZONE.

ePRIVACY ZONEf
1	2	3	4	5	6
7	8	9	10	11	12
PRIVACY SET					ON
STYLE				COLOR
Y-LEVEL			[128]
RED			[128]
BLUE			[128]

Use the cdefswitch to select one from PRIVACY 1 through 12.

Select one from PRIVACY 1~12 and press the SETUP switch to confirm your setting. You can specify a pixel that moves as you change the PIXEL LEVEL to set the position.

PRIVACY ZONE SET1

PIXEL LEVEL				[4]
<POINT>
<POSITION>

- How to set the point

You can set each position of the 4 points.

If you press the SETUP switch in <POINT>, you will see the points available in the PRIVACY ZONE. Each time you press the SETUP switch, the points available will move.

Use the cdefswitch to set the position of each point. Set each position of the four points and press the SETUP switch to complete the positioning.

-How to set the position

You can move the position of the overall area.

By pressing the SETUP switch in <POSITION>, you can move the overall position of the privacy zone.

Use the cdefswitch to move the position and press the SETUP switch to confirm it.

Note :

–If more than one PRIVACY ZONE is specified and the PRIVACY SET is set to ON, the PIP function will be deactivated.

–If the 12th PRIVACY ZONE is specified, the LINE function of FENCE will be deactivated.

22 – DIGITAL COLOR CAMERA

How to use OSD Menu

OTHER SET

eOTHER SETf
FACTORY DEFAULTS
OSD COLOR	BW

SYSTEM INFORMATION

eSYSTEM INFOf

TYPE	3_BOX_NOR_P
SERIAL NO. 000000000000000
CAMERA VER.	0.50_090101

FACTORY DEFAULTS

All the settings will be restored to the factory default.

However, the settings of LANGUAGE will not be restored to the default.

OSD COLOR

[BW, R/G/B]

You can set the OSD(On-screen Display) color to COLOR or B/W.

You can view the system information including the serial number, camera version..

LANGUAGE

eLANGUAGEf

ENG

ÃENGLISH FRANÇAIS DEUTSCH ESPAÑOL ITALIANO

The camera supports 5 different languages.

Select a preferred language.

English – 23

How to use OSD Menu

Initial Configuration Table

• Camera Configuration

CAMERA ID	OFF
IRIS	ALC
AGC	VERY HIGH
DNR	MID
SHUTTER	OFF
FLICKERLESS	(OFF)
XDR	MID
DAY/NIGHT	AUTO
DETAIL	[2]
AGC COLOR SUP	MID
REVERSE	OFF
POSI/NEGA	+
PIP	OFF
DIS	OFF
V-SYNC	INT

24 – DIGITAL COLOR CAMERA

Specifications

SPECIFICATIONS

Items	Sub-items			SCC-B1331N
Camera Type				CCTV Camera
		Device		1/3” Super-HAD PS CCD
Image	Pixels		Total	811 x 508
			Effective	768 x 494
	System			Interlace/Progressive
	Scanning Line			525 lines
	Frame			30frame/1sec
Scanning	Horizontal		Internal Mode	15,734 Hz
	Frequency		Line-lock Mode	15,750 Hz
	Vertical		Internal Mode	59.94 Hz
	Frequency		Line-lock Mode	60 Hz

		Condition			Min. Scene illumination
Min. Scene	Sens-up	F No.		Level	DAY		NIGHT
	OFF	1.2	50	IRE	0.4	Lux	0.4	Lux
Illumination
	OFF	1.2	30	IRE	0.24	Lux	0.24	Lux
									ENG
	OFF	1.2	15	IRE	0.12	Lux	0.12	Lux
	Number of Privacy Zone				12 (Polygonal Method)
	Day/Night				DAY/NIGHT/AUTO/EXT
	Motion Detection				OFF/Tracking/Detection
	eXtended Dynamic Range(XDR)				Off/On (Level Setting)
	D-Zoom				x1 ~ x16 (x0.1 STEP)
	PIP					Off/On
	High Speed Shutter				1/60 ~ 1/10Ksec (OSD/External Control)
	Flickerless					Off/On
	Sens-Up					x2 ~ x512
Functions	BLC				Off/On (Area Setting)
	AGC				Off/On (Max.Level Setting)
	ELC				Off/On ( ~ 1/200K sec)
	Line Lock				Off/On (Phase Control)
	Camera ID				Off/On (Max.54ea/2Line)
	White Balance				ATW1/ATW2/AWC/3200K/5600K
	Digital Noise Reduction(DNR)				Off/On (Adaptive 3D+2D)
	Digital Image Stabilization(DIS)					Off/On
	Intelligent Video					Fixed/Moved
	Etc. Function				Detail, Reverse(H/V), Posi/Nega
Resolution	Horizontal					600 TV Lines
	Vertical					350 TV Lines

Video Output	-	VBS 1.0Vp-p, 75 Ω
S/N Ratio	S/N Ratio	Approx. 52dB

English – 25

Specifications

	Items	Sub-items			SCC-B1331N
	Lens	Lens Drive Type			MANUAL/AI(VIDEO/DC)
		Mount Type			CS/C
	Alarm	Input			N/A
		Output			1 Output
	Remote	Coaxitron (Data On Coax cable)			Yes (with SCX-RD100)
	Control
	Environmental	Operating Temperature			-10˚C ~ +50˚C
	Conditions	Humidity			Less than 90%
		Power Requirement			AC24V ± 10%(60Hz ± 0.3Hz)
					DC12V ± 10%
	Power	Power Consumption			In normal operation : 2.2W
		(With DC Lens)
		LED Indicator			Yes
		Dimensions		Net	64(W) x 58(H) x 109.2(D) mm
	Physical	(WxHxD)		Package	173(W) x 99(H) x 115(D) mm
				Net	305g
	Specification	Weight
				Package	530g
		Color		Body	Silver

26 – DIGITAL COLOR CAMERA

				Specifications
Items	Sub-items			SCC-B1331P / SCC-B1031P
Camera Type				CCTV Camera
		Device		1/3” Super-HAD PS CCD
Image	Pixels		Total	795 x 596
			Effective	752 x 582
	System			Interlace/Progressive
	Scanning Line			625 lines
	Frame			25frame/1sec
Scanning	Horizontal		Internal Mode	15,625 Hz
	Frequency		Line-lock Mode	15,625 Hz
	Vertical		Internal Mode	50 Hz
	Frequency		Line-lock Mode	50 Hz

			Condition			Min. Scene illumination
	Min. Scene	Sens-up	F No.		Level	DAY		NIGHT
		OFF	1.2	50	IRE	0.4	Lux	0.4	Lux
	Illumination
		OFF	1.2	30	IRE	0.24	Lux	0.24	Lux
		OFF	1.2	15	IRE	0.12	Lux	0.12	Lux
		Number of Privacy Zone				12 (Polygonal Method)			ENG
		Day/Night				DAY/NIGHT/AUTO/EXT
		Motion Detection				OFF/Tracking/Detection
		eXtended Dynamic Range(XDR)				Off/On (Level Setting)
		D-Zoom					Max. x16
		PIP					Off/On
		High Speed Shutter				1/50 ~ 1/10Ksec (OSD/External Control)
		Flickerless					Off/On
		Sens-Up					x2 ~ x512
	Functions	BLC				Off/On (Area Setting)
		AGC				Off/On (Max.Level Setting)
		ELC				Off/On ( ~ 1/200K sec)
		Line Lock				Off/On (Phase Control)
		Camera ID				Off/On (Max.54ea/2Line)
		White Balance				ATW1/ATW2/AWC/3200K/5600K
		Digital Noise Reduction(DNR)				Off/On (Adaptive 3D+2D)
		Digital Image Stabilization(DIS)					Off/On
		Intelligent Video					Fixed/Moved
		Etc. Function				Detail, Reverse(H/V), Posi/Nega
	Resolution	Horizontal					600 TV Lines
		Vertical					350 TV Lines
	Video Output	-				VBS 1.0Vp-p, 75 Ω
	S/N Ratio	S/N Ratio					Approx. 52dB

English – 27

Specifications

	Items	Sub-items			SCC-B1331P / SCC-B1031P
	Lens	Lens Drive Type			MANUAL/AI(VIDEO/DC)
		Mount Type			CS/C
	Alarm	Input			N/A
		Output			1 Output
	Remote	Coaxitron (Data On Coax cable)			Yes (with SCX-RD100)
	Control	RS-485			Yes (Multi Protocol, 8ea)
	Environmental	Operating Temperature			-10˚C ~ +50˚C
	Conditions	Humidity			Less than 90%
					SCC-B1331P : AC24V ± 10%(50Hz±0.3Hz)
		Power Requirement			DC12V ± 10%
					SCC-B1031P : AC220V ± 10%(50Hz±0.3Hz)
	Power				In Normal operation :
		Power Consumption			SCC-B1331P : 2.2W
		(With DC Lens)			SCC-B1031P : 3.3W
		LED Indicator			Yes
		Dimensions		Net	SCC-B1331P : 64(W) x 58(H) x 109.2(D) mm
					SCC-B1031P : 64(W) x 58(H) x 129.2(D) mm
		(WxHxD)
				Package	173(W) x 99(H) x 115(D) mm
	Physical			Net	SCC-B1331P : Approx. 305g
	Specification				SCC-B1031P : Approx. 395g
		Weight
				Package	SCC-B1331P : Approx. 530g
					SCC-B1031P : Approx. 620g
		Color		Body	Silver

28 – DIGITAL COLOR CAMERA

Correct Disposal of This Product (Waste Electrical & Electronic Equipment)

(Applicable in the European Union and other European countries with separate collection systems)

This marking on the product, accessories or literature indicates that the product and its electronic accessories (e.g. charger, headset, USB cable) should not be disposed of with other household waste at the end of their working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate these items from other types of waste and recycle them responsibly to promote the sustainable reuse of material resources.

Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take these items for environmentally safe recycling.

Business users should contact their supplier and check the terms and conditions of the purchase contract. This product and its electronic accessories should not be mixed with other commercial wastes for disposal.

SCC-B1331(P)

SCC-B1031P

CAMERA NUMERIQUE

COULEUR

Manuel d’utilisation

FRE

Imaginez les possibilités

Nous vous remercions d’avoir choisi ce produit Samsung. Pour bénéfi cier d’un service plus complet,

veuillez enregistrer votre produit sur le site

www.samsungsecurity.com