Samsung SCC-520P User Manual
Digital Color Dome Camera
SCC-520N/520P
User's guide
CCTV COLOR DOME CAMERA SCC-520N/520P is the monitoring
camera incorporated with the recent CCD that provides the best
monitoring function in connection with the CCTV system equipment.
■ Number of CCD pixels
• SCC-520N : 270,000 pixels
• SCC-520P : 320,000 pixels
■ Power supply
• SCC-520N :
DC 12V
• SCC-520P :
■ Automatic function and special function
• ATW
• ELC(Electronic shutter iris)
■ Fixed focus lens
• Fixed focus lens installed on the camera.
Please take cautions that any dust or foreign matter gathers
on the front glass surface of the lens.
■ Main body
• A body that supports the camera.
■ PCB board
• This part is quite important since it performs the camera
function.
Please handle with care.
■ Power cable
• The terminal that is connected to the power (adaptor) cable.
Connect to DC 12V.
■ Video signal output cable
• The cable that sends the video signal.
■ Dome cover
• The transparent plastic cover that protects the camera.
Be careful not to make a scratch on it.
Video cable
Dome cover
Fixed focus lens
PCB board
Main body
Power cable
Component Name
Function of Each Component
Overview
ELECTRONICS
Printed In Korea
AB68-00140A
■ Check what is inside the package
• Check to see if the following parts are included in the
purchased package.
■ Notes on installation and usage
1. Users should not disassemble the camera from the front
direction.
2. Always handle the camera with care. Please do not apply a
shock or vibration as much as possible and take cautions
not to cause damage or make a scratch on the camera due
to careless storage.
3. Please do not install the camera with the rainy place or
highly humid areas. And do not operate the camera in the
wet place.
4. Do not clean the camera body with the strong abrasives or
soaps. When the camera becomes dirty, clean it with the
dry rugs. Especially, make sure to use the dedicated rugs for
lens to clean the dome cover.
5. Please select the camera in the cool area that is not exposed
to the direct sunlight. If you do, it can cause bad effects on
the product.
■ Cable connection
Hold the camera body with one hand and turn the dome
cover counterclockwise with other hand in order to
disassemble it.
Specifications
Installation
Please make sure that any foreign matter gathers on
the lens cover when assembling or disassembling the
dome cover.
Note
1
Connect the BNC cable to the video cable connector attached
on the dome camera, and connect the remained BNC cable
to the video input terminal of the monitor.
2
Connect the power adaptor at this time. Connect the DC 12V
power cable of the connector to the power cable connection
that is attached on the dome camera. For connection of the
AC input of the adaptor, please select 110V or 220V switch
in advance.
3
Attach the camera on the target location with the screw
driver using the provided tab screw.
4
110
220
Monitor
BNC Cable
Power Cable ( )
Wall or ceiling
Main body
Tab screw
Screw Driver
Set the proper image by moving the camera body (PCB board)
inside the dome camera upward or downward and set the
focus by turning the lens to the left or right direction.
5
Wall or ceiling
Adjust the
image upward
or downward
Adjust focus by
turning left or right
Assemble the dome cover by turning it clockwise.
6
Item
Broadcasting method
CCD
Valid pixel
Synchronization method
Resolution
Signal output
S/N rate
Lowest illumination
of the thing pictured
Gamma correction
In/out connector
Operational temperature
Voltage
Power consumption
Lens
External size
Weight
Details
SCC-520N:NTSC STANDARD
SCC-520P:PAL STANDARD
1/3" SUPER HAD IT CCD
SCC-520N: 510(H) x 492(V)
SCC-520P: 500(H) x 582(V)
Internal
H : 330 TV Lines, V : 350 TV Lines
VBS 1.0Vp-p(75Ω composite)
48dB
2Lux(F2.0, 50 IRE)
0.45
Signal output: BNC, Power input : DC jack
-10~+50°C
DC 12V, 200mA
2 W
Focal Length(f) : 3.8mm
Aperture Ratio(F) : 2.0
UP/Version DATA
100(ø) x 67(H)mm
150g
Camera
User's guide
tab screw
Loading...