Samsung SC-7060 User Manual
EN
Operating Instructions
VACUUM CLEANER
❈ Before operating this unit, please read the instructions carefully.
❈ For indoor use only.
Register your product at www.samsung.com/global/register
ASSEMBLING THE CLEANER
1
Features may vary according to model.
▼
For storage, park the floor nozzle.
EN-1
OPERATING YOUR CLEANER
2
2-1 POWER CORD
2-2 HANDLE CONTROL TYPE ONLY
• SLIDE TO THE STOP POSITION
Vacuum-cleaner switches off (stand by mode)
• SLIDE FORWARD TO MAX
Suction capacity increases smoothly up to maximum.
NOTE
When removing the plug
from the socket, please
take care to grasp the
plug, not the cord in order
to avoid undue stress.
2-3 USING CYCLONE FILTER
EN-2
2-4 USING FLOOR TOOLS
OPTION
CREVICE
DUSTING
UPHOLSTERY
OPTION
PARQUET SPECIALIST
- TRANSPARENT TUBE
CHECK FILTER INDICATOR
3
EN-3
HARD FLOOR
When the light is illuminated, check
the Cassette Filter and clean it.
OPTIONAL (Dust Bag type)
Check the Dust bag and change it.
MAINTAINING THE CASSETTE FILTER
4
4-1 EMPTYING THE CASSETTE FILTER(Optional)
1 2 3
6 5 4
• Ensure completely dry
before replacing.
• Allow 12 hours for it to dry.
• Brush the Filter media with
water until the stuck fine
dust is removed.
7 8 9
NOTE
The cassette filter should be washed thoroughly as well as emptied if:
•
the CHECK FILTER indicator lights continuously
•
the suction power feels weaker than normal
•
the Turbo Brush (optional) is not working properly
EN-4
4-2 CHANGING THE DUST BAG (Optional)
12 3
OPTIONAL
●
FOR CLOTH FILTER BAG
After using, if the cloth bag is full of dust, clean the cloth filter bag and use it again.
CLEANING THE CYCLONE FILTER (Optional)
5
1 2 3
4 5 6
VP-95B TYPE
7
- CLEANING THE INNER PART OF CYCLONE FILTER
8
EN-5
NOTE
It is necessary to use
Cyclone Filter while cleaning.
CLEANING THE INLET FILTER
6
1 2 3
:
NOTE
OUTLET FILTER
7
Do not allow the filter to become clogged as this may cause power reduction or may damage the motor.
12
- IF YOU HAVE A PROBLEM
PROBLEM CAUSE REMEDY 0
Motor does not start.
Suction force is gradually
decreasing.
Cord does not rewind fully. Check that the cord is not
Vacuum cleaner does not
pick up dirt.
No power supply.
Thermal cut-out.
Nozzle, suction hose or tube
is blocked.
twisted or wound unevenly.
Crack or hole in hose.
EN-6
Check cable, plug and socket.
Leave to cool.
Remove the object and
empty/wash cassette filter as
required.
Pull the cord out 2-3m and
push down the cord rewind
button.
Check hose and replace if
required.
IMPORTANT SAFEGUARDS
1. Read all instructions carefully. Before switching on, make sure that the voltage of your
electricity supply is the same as that indicated on the rating plate on the bottom of the
cleaner.
2. WARNING: Do not use the vacuum cleaner when rug or floor is wet.
Do not use to suck up water.
3. Close supervision is necessary when any appliance is used by or near children. Do not
allow the vacuum cleaner to be used as a toy. Do not allow the vacuum cleaner to run
unattended at any time. Use the vacuum cleaner only for its intended use as described in
these instructions.
4. Do not use the vacuum cleaner without Cassette Filter. Empty the Cassette Filter before it
is full in order to maintain the best efficiency.
5. Do not use the vacuum cleaner to pick up matches, live ashes or cigarette butts. Keep the
vacuum cleaner away from stoves and other heat sources. Heat can deform and discolour
the plastic parts of the unit.
6. Avoid picking up hard, sharp objects with the vacuum cleaner as they may damage the
cleaner parts. Do not stand on the hose assembly. Do not put a weight on the hose. Do
not block the suction or the exhaustion part.
7. Switch the vacuum cleaner off at the machine before unplugging from the electrical outlet.
Grasp the plug to disconnect cord from the electrical outlet before caring Cassette Filter
and filters.
8. The plug must be removed from the socket out-let before cleaning or maintaining the
appliance.
9. The use of an extension cord is not recommended.
10. If your vacuum cleaner is not operating correctly, switch off the power supply and consult
an authorized service agent.
11. If the supply cord is damaged, it must be replaced by the manufacturer or its service
agent or a similarly qualified person in order to avoid a hazard.
This Vacuum cleaner is approved the following.
EMC Directive : 89/336/EEC , 92/31/EEC and 93/68/EEC
Low Voltage Safety Directive : 73/23/EEC and 93/68/EEC
EN-7
Loading...