Samsung S5G9801X01-D0B0, S5G9803X01-D0B0 Datasheet
INFRAED REMOCON RECEIVER S5G9801X01/S5G9803X01
INTRODUCTION
The S5G9801X01 and S5G9803X01 are CMOS integrated circuits for
the infrared ray remote receiver, used with the S5G9802, which can
be applied to TV, VCR, VDP, CDP and AV controller.
The S5G9801X01 is a 16-DIP type and is able to control 10 functions.
The S5G9803X01 is a 24-DIP type and is able to control 18 functions.
FEATURES
• Output for continuous pulse, toggle pulse and single pulse are
provided (Toggle pulse is available only for S5G9803X01)
• A single terminal type oscillator by means of RC is provided
• Containing custom code detection circuit for code check with
the transmitter (To prevent interferences with other models)
• Able to output in parallel method multiple keying signals sent
from transmitter.
The S5G9801X01 can output up to 5 functions, and the S5G9803X01 can output up to 6 functions in parallel
method.
16−DIP−300A
24−DIP−400
ORDERING INFORMATION
Device Package Operating Temperature
S5G9801X01-D0B0 16−DIP−300A
S5G9803X01-D0B0 24−DIP−400
− 20°C − +75°C
1
S5G9801X01/S5G9803X01 INFRAED REMOCON RECEIVER
BLOCK DIAGRAM
V
GND
DD
16
1
OSC
REMIN
CODE1
CODE2
15
14
13
OSC
2
DATA
INPUT
SYSTEM
CODEINPUT
DIVIDER
DATABIT
COUNTER
COMPARATOR
CLOCK
GENERATOR
DATA
REGISTER
OUTPUT LATCH
& DRIVER
CP1
CP2
CP3
CP4
CP5
CP6
SP1
SP2
SP3
SP4
SP5
SP6
SP7
SP8
SP9
SP10
TP1
TP2
Figure 1.
2
INFRAED REMOCON RECEIVER S5G9801X01/S5G9803X01
PIN CONFIGURATION
VSS
REMIN
CP1
CP2
CP3
CP4
CP5
SP5
1
2
3
4
S5G9801X01
5
6
7
8
16
15
14
13
12
11
10
9
VDD
OSC
CODE2
CODE3
SP1
SP2
SP3
SP4
VSS
REMIN
CP1
CP2
CP3
CP4
TP5
TP6
TP2
TP1
SP10
SP9
1
2
3
4
5
6
S5G9803X01
7
8
9
10
11
12
24
23
22
21
20
19
18
17
16
15
14
13
VDD
OSC
CODE1
CODE2
SP1
SP2
SP3
SP4
SP5
SP6
SP7
SP8
Figure 2.
3
S5G9801X01/S5G9803X01 INFRAED REMOCON RECEIVER
PIN DESCRIPTION
Pin No
Symbol
S5G9801 S5G9803
Input
Output
1 1 GND Ground −
2 2 REMIN
3 − 7 − CP1 − SP5
− 3 − 8 CP1 − CP6
− 9 − 10 TP1, TP2
8 ~ 12 − SP1 − SP5
− 11 − 20 SP1 − SP10
Receiving Signal
Input
Continuous Signal
output
Toggle Signal
Output
Single Signal Output
Instruction signal input with the carrier signal
eliminated.
As long as receiving is input, this output is held at “H”
level. After releasing a key, output is held at “H” level
for about 160 msec.
When receiving signal is input, output is toggled.
When receiving signal is input, output is held at “H”
level only for about 107 msec.
A code set at this terminal is compared with tran-
13, 14 21, 22 CODE Code Input
smitter code and if they agree with each other, input is
accepted (built-in pull-up resistor).
15 33 OSC Timing Oscillation
A capacitor and a resistor are connected in parallel
method between this terminal and VSS.
16 24 VDD Power Supply −
Description
ABSOLUTE MAXIMUM RATINGS (TA = 25×C)
Characteristic Symbol Value Unit
Supply Voltage V
Input/Output Voltage VIN V
Power Dissipation P
Operating Temperature T
Storage Temperature T
DD
OUT
D
OPR
STG
0 − 6 V
VSS −0.3 − VDD + 0.3 V
200 mW
−20 − 75 °C
−55 − 125 °C
4
INFRAED REMOCON RECEIVER S5G9801X01/S5G9803X01
ELECTRICAL CHARACTERISTICS
(Ta = 25 ×C, VDD = 5 V, unless otherwise specified)
Characteristic Symbol Test Conditions Min. Typ. Max. Unit
Operating Voltage V
Operating Current I
Frequency Deviation f
DD
DD
OSC
Ta = −25°C ~ 75°C 4.5 − 5.5 V
Output Without Load − − 1.0 mA
Ta = −25°C − 75°C
VDD = 4.5V − 5.5V
27 38 57 kHz
Frequency Stability
∆V
∆T
Output “H” Level I
Current “L” Level I
Input Current “H” Level I
Pull-up Resistor R
Input Circuit Threshold
Voltage
V
V
Hysteresis Width VH
Standard osc Frequency S
FOSC
FOXC
FOSC
OH
OL
IH
UP
IH
IL
2S
Ta = −25°C
VDD = 4.5V − 5.5V
−5 − 5 %
Ta = −30°C − 75°C −5 − 5 %
All Output, VOH = 4V − −2.0 −1.0 mA
All Output, VOL = 1V 1.0 2.5 − mA
Code Terminal, VIH = 5.0V −1.0 − 1.0 uA
REMAIN Terminal 10 20 40 kΩ
REMAIN Terminal 3.5 − − V
REMAIN Terminal − − 1.5 V
− − 1.0 − V
− − 38 − kHz
5
Loading...