Refrigerator
user manual
This manual is made with 100% recycled paper.
English
imagine the possibilities
Thank you for purchasing a Samsung product.
To receive a more complete service,
please register your product at
www.samsung.com/register
Free Standing Appliance
DA99-01745T-EN.indd 01DA99-01745T-EN.indd 01 2011.6.27 3:28:48 PM2011.6.27 3:28:48 PM
safety information
SAFETY INFORMATION
WARNING
WARNING
CAUTION/WARNING SYMBOLS USED
WARNING
OTHER SYMBOLS USED
These warning signs are here to prevent injury to you
and others.
Please follow them explicitly.
After reading this section, keep it in a safe place for
future reference.
CE Notice
This product has been determined to be in
compliance with the Low Voltage Directive
(2006/95/EC), the Electromagnetic Compatibility
Directive (2004/108/EC) and the Eco-Design
Directive(2009/125/EC) implemented by Regulation
(EC) No 643/2009 of the European Union.
Before operating the appliance, please •
read this manual thoroughly and retain it
for your reference.
Because these following operating •
instructions cover various models, the
characteristicserator may differ slightly
from those described in this manual.
Indicates that a danger of death or
serious injury exists.
Indicates that a risk of personal injury or
CAUTION
material damage exists.
Represents something you must NOT do.
Represents something you must NOT
disassemble.
Represents something you must NOT
touch.
Represents something you must follow.
Indicates that you must disconnect the
power plug from the socket.
Represents a ground is needed to prevent
electric shock.
It is recommended that this symbol be
handled by service man.
described in this instruction manual.
We strongly recommend that any servicing be •
performed by a qualifi ed individual.
R600a or R134a can be used as a refrigerant. •
Check the compressor label on the rear of the
appliance and the rating label inside the fridge to
see which refrigerant is used for the refrigerator.
In case of R600a refrigerant, this gas •
is natural gas with high environmental
compatibility that is, however, also
combustible. When transporting and
installing the appliance, care should
be taken to ensure that no parts of the
refrigerating circuit are damaged.
Refrigerant squirting out of the pipes could ignite •
or cause an eye injury. If a leak is detected,
avoid any naked fl ames or potential sources of
ignition and air the room in which the appliance is
standing for several minutes.
In order to avoid the creation of a fl ammable •
WARNING
gas-air mixture if a leak in the refrigerating
circuit occurs, the size of the room in
which the appliance may be sited depends
on the amount of refrigerant used.
Never start up an appliance showing any signs of •
damage. If in doubt, consult your dealer.
The room must be 1m3 in size for every 8g of •
R600a refrigerant inside the appliance.
The amount of refrigerant in your particular •
appliance is shown on the identifi cation plate
inside the appliance.
Please dispose of the packaging material for this •
product in an environmentally friendly manner.
This appliance is not intended for use by persons •
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience
and knowledge, unless they have been given
supervision or instruction concerning use of the
appliance by a person responsible for their safety.
Children should be supervised to ensure that they •
do not play with the appliance.
This refrigerator must be properly installed and •
located in accordance with the manual before it is
used.
Use this appliance only for its intended purpose as •
02_ safety information
DA99-01745T-EN.indd 02DA99-01745T-EN.indd 02 2011.6.27 3:28:48 PM2011.6.27 3:28:48 PM
SEVERE WARNING SIGNS
Do not install the refrigerator in a damp •
WARNING
place or place where it may come in
contact with water.
Deteriorated insulation of electrical parts may cause an electric shock or fi re.
Do not place this refrigerator in direct sunlight or •
expose to the heat from stoves, room heaters or
other appliance.
Do not plug several appliances into the same •
power socket. The refrigerator should always be
plugged into its own individual electrical which has
a voltage rating that matched the rating plate.
This provides the best performance and also prevents overloading house wiring circuits, which
could cause a fi re hazard from overheated wires.
Make sure that the power plug is not squashed or •
damaged by the back of the refrigerator.
Do not bend the power cord excessively or place •
heavy articles on it.
This constitutes a fi re hazard. Have the power cord repaired or replaced •
immediately by the manufacturer or its service
agent if power cord has become frayed or
damaged.
Do not use a cord that shows cracks or abrasion •
damage along its length or at either end.
If the power cord is damaged, have it replaced •
immediately by the manufacturer or its service
agent.
When moving the refrigerator, be careful not to roll •
over or damage the power cord.
Do not insert the power plug with wet hands.•
Unplug the refrigerator before cleaning and •
making repairs.
Do not use a wet or damp cloth when cleaning •
the plug.
Remove any foreign matter or dust from the power •
plug pins.
Otherwise there is a risk of fi re. If the refrigerator is disconnected from the power •
supply, you should wait for at least ten minutes
before plugging it back.
If the wall socket is loose, do not insert the power •
plug.
There is a risk of electric shock or fi re. The appliance must be positioned so that the plug •
is accessible after installation.
The refrigerator must be grounded.•
You must ground the refrigerator to prevent any power leakages or electric
shocks caused by current leakage from
the refrigerator.
Never use gas pipes, telephone lines or •
other potential lightening rods as ground.
Improper use of the ground plug can result in electric shock.
Do not dissemble or repair the refrigerator by •
yourself.
You run risk of causing a fi re, malfunction and/or personal injury.
If you smell pharmaceutical or smoke, pull •
out power plug immediately and contact your
Samsung electronics service center.
Keep ventilation opening in the appliance •
enclosure or mounting structure clear of
obstruction.
Do not use mechanical devices or any other •
means to accelerate the defrosting process, other
than those recommended by the manufacturer.
Do not damage the refrigerant circuit.•
Do not place or use electrical appliance inside •
the refrigerator/freezer, unless they are of a type
recommended by the manufacturer.
Before changing the interior light, unplug the •
appliance from the power supply.
If you experience diffi culty when changing the •
light, contact your service center.
The appliance is not intended for use by persons •
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience
and knowledge, unless they have been given
supervision or instruction concerning use of the
appliance by a person responsible for their safety.
Children should be supervised to ensure that they •
do not play with the appliance.
Do not let children hang on the door. If not, a •
serious injury may occur.
Do not touch the inside walls of the freezer or •
products stored in the freezer with wet hands.
This may cause frostbite. If the refrigerator is not to be used for a long •
period of time, pull out the power plug.
Deterioration in the power cord insulation may cause fi re.
Do not store articles on the top of the appliance.•
When you open or close the door, the articles may fall and cause personal injury and/or material
damage.
CAUTION SIGNS
CAUTION
This product is intended only for the •
storage of food in a domestic environment.
Manufacturer’s recommended storage times and •
expiry dates of frozen foods should be adhered to.
Refer to relevant instructions
Bottles should be stored tightly together so that •
they do not fall out.
Do not place carbonated or fi zzy drinks in the •
safety information _03
DA99-01745T-EN.indd 03DA99-01745T-EN.indd 03 2011.6.27 3:28:48 PM2011.6.27 3:28:48 PM
freezer compartment
Do not overfi ll the refrigerator with food.•
When you open the door, an item may fall out and cause personal injury or material damage.
Do not put bottles or glass containers in the •
freezer.
When the contents freeze, the glass may break •
and cause personal injury.
Do not spray infl ammable gas near the refrigerator.•
There is a risk of explosion or fi re. Do not directly spray water inside or outside the •
refrigerator.
There is a risk of fi re or electric shock. Do not store volatile or fl ammable substances in •
the refrigerator.
The storage of benzene, thinner, alcohol, ether, LP gas and other such products may cause
explosions.
If you have a long vacation planned, it is advisable •
to empty the appliance or use the vacation
function.
Do not store pharmaceuticals products, scientifi c •
materials or temperature-sensitive products in the
refrigerator.
Products that require strict temperature controls must not be stored in the refrigerator.
Do not put a container fi lled with water on the •
refrigerator.
If spilled, there is a risk of fi re or electric shock. -
CAUTION SIGNS FOR
CLEANING
CAUTION
Never put fi ngers or other objects into the •
dispenser hole and ice chute.
It may cause personal injury or material damage. Do not use a wet or damp cloth when cleaning •
the plug, remove any foreign material or dust from
the power plug pins.
Otherwise there is a risk of fi re. -
WARNING SIGNS FOR
DISPOSAL
When disposing of this or other refrigerators, •
remove the door/door seals, door latch so that
small children or animals cannot become trapped
inside.
Leave the shelves in place so that children may •
not easily climb inside.
R600a or R134a is used as a refrigerant. Check •
the compressor label on the rear of the appliance
or the rating label inside the fridge to see which
refrigerant is used for your refrigerator. When
this product contains fl ammable gas (Refrigerant
R600a) contact your local authority in regard to
04_ safety information
safe disposal of this product.
Cyclopentane is used as a insulation blowing gas. •
The gases in insulation material require special
disposal procedure. Please contact your local
authorities in regard to the environmentally safe
disposal of this product. Ensure that none of the
pipes on the back of the appliances are damaged
prior to disposal. The pipes shall be broke in the
open space.
In the event of a power failure, call the local
offi ce of your Electricity Company and ask
CAUTION
how long it is going to last.
Most power failures that are corrected in an hour or
two will not affect your refrigerator temperatures.
However, you should minimize the number of door
openings while the power is off.
But should the power failure last more than 24hours,
remove all frozen food.
For doors or lids fi tted with locks and keys, the keys
be kept out of the reach of children and not in the
vicinity of the refrigerating appliance, in order to
prevent children from being locked inside.
ADDITIONAL TIPS FOR PROPER
USAGE
Allow the appliance to stand for 2 hours •
after installation.
To get best performance of product,•
Do not place foods too closely in front of the vents at the rear of the appliance as it can obstruct free
air circulation in the freezer compartment.
Wrap the food up properly or place it in airtight containers before put it into the fridge freezer
Do not put any newly introduced food for freezing near to already frozen food.
There is no need to disconnect the refrigerator •
from the power supply if you will be away for
less than three weeks. But, remove all the food if
you are going away for the three weeks or more.
Unplug the refrigerator and clean it, rinse and dry.
The appliance might not operate consistently •
(possibility of defrosting of contents or
temperature becoming too warm in the frozen
food compartment) when sited for an extended
period of time below the cold end of the range of
temperatures for which the refrigerating appliance
is designed.
Do not store food which goes bad easily at low •
temperature, such as bananas, melons.
Place the ice tray at the originally provided •
posistion by manufacturer in order to achieve
optimal ice-freezing.
DA99-01745T-EN.indd 04DA99-01745T-EN.indd 04 2011.6.27 3:28:48 PM2011.6.27 3:28:48 PM
Your appliance is frost free, which means there is •
no need to manually defrost your appliance, as
this will be carried out automatically.
Temperature rising during the defrost can comply •
with ISO requirement. But If you want to prevent
an undue rise in the temperature of the frozen
food while defrosting the appliance, please wrap
the frozen food in several layers of paper such as
newspaper.
Any increase in temperature of frozen food during •
defrosting can shorten its storage life.
Contains fl uorinated greenhouse gases covered •
by the Kyoto Protocol.
Foam blown with fl uorinated greenhouse gases.•
Foam blown additive:
Perfl uorohexane Global Warming
Potential (GWP) = 9000
SAVING ENERGY TIPS
Install the appliance in a cool, dry room with adequate ventilation. Ensure that it is not exposed
to direct sunlight and never put it near a direct
source of heat (radiator, for example).
Never block any vents or grilles on the appliance. Allow warm food to cool down before placing it in the appliance.
Put frozen food in the refrigerator to thaw. You can then use the low temperatures of the
frozen products to cool food in the refrigerator.
Do not keep the door of the appliance open for too long when putting food in or taking food out.
The shorter time for which the door is open, the
less ice will form in the freezer.
Clean the rear of the refrigerator regularly. Dust increases energy consumption.
Do not set temperature colder than necessary. Ensure suffi cient air exhaust at the refrigerator base and at the back wall of the refrigerator.
Do not cover air vent openings.
Allow clearance to the right, left, back and top when installing. This will help reduce power
consumption and keep your energy bills lower.
contents
SETTING UP YOUR SIDE-BY-SIDE REFRIGERATOR ……………………………………………………… 06
OPERATING THE SAMSUNG SIDE-BY-SIDE REFRIGERATOR …………………………………………… 13
TROUBLESHOOTING …………………………………………………………………………………………… 19
safety information _05
DA99-01745T-EN.indd 05DA99-01745T-EN.indd 05 2011.6.27 3:28:49 PM2011.6.27 3:28:49 PM
setting up your side-by-side
at least 6mm
at least 6mm
Leg
Screw Driver
refrigerator
GETTING READY TO INSTALL
THE REFRIGERATOR
Congratulations on the purchase of your Samsung
Side-By-Side Refrigerator. We hope you will enjoy
the many state-of-the-art features and effi ciencies
that this new appliance has to offer.
Selecting the best location for the
refrigerator
Select a location with easy access to the water •
supply.
Select a location without direct exposure to •
sunlight.
Select a location with level (or nearly level) fl ooring.•
Select a location with enough space for the •
refrigerator doors to open easily.
Allow suffi cient space to the right, left, back and •
top for air circulation.
If your refrigerator is not level, the internal cooling system may not work correctly.
Refer to drawing and dimensions below for overall space required for use.
Please ensure that appliance can be moved freely •
in the event of maintenance & service.
at least 6mm
When moving your refrigerator
To prevent fl oor damage be sure the front levelling
at least 6mm
legs are in the up position (above the fl oor). Refer to
‘Levelling the refrigerator’ in the manual(at page 10).
To protect the fi nish of the fl ooring, place the
protection sheet such as packing carton under the
refrigerator.
Leg
When installing, servicing or cleaning behind
CAUTION
the refrigerator, be sure to pull the unit straight
out and push back in straight after fi nishing.
First things fi rst! Make sure that you can easily move
your refrigerator to its fi nal location by measuring
doorways (both width and height), thresholds,
ceilings, stairways, etc. The following chart details
the exact height and depth.
Model RSG5* RSG5*CRS
Without Door 908 908
Width
With Door 912 912
Dimension
(mm)
Do not install the refrigerator where the •
temperature can drop below 10°C.
Make sure you disconnect the water supply line •
BEFORE removing the freezer door. See the next
section on “Separating the Water Line” to avoid
damage.
Only Cabinet 600 600
Depth
Without Handle 687 687
With Handle 737 742
Without Door 1745 1745
Height
With Door 1780 1780
Allow clearance to the right, left, back and •
top when installing. This will help reduce
power consumption and keep your energy
bills lower.
Screw Driver
06_ setting up06_ setting up
DA99-01745T-EN.indd 06DA99-01745T-EN.indd 06 2011.6.27 3:28:49 PM2011.6.27 3:28:49 PM
USING THE ICE MAKER
Figure1
Figure2
Ice Chute
Line
Line
Coupler
Coupler
To Remove the Ice
Bucket
Hold the handle as shown in fi gure1.
Slightly pull up the bottom part. Take out the ice bucket slowly. -
Figure1
To Refi t The Ice Bucket
Assemble it in the reverse order of disassembly.
Push the bucket in fi rmly until you hear a clicking sound.
When the bucket does not fi t into its place, turn the gear
handle on its back by 90
degrees and reinstall it again as
shown in fi gure 2.
Normal Operation
Any sounds you hear when the ice maker dumps ice into
the bucket are part of normal
operation.
Not dispensing ice for long periods may cause ice clumps
in the ice bucket. Remove the
remaining ice and empty the
bucket.
When ice does not come out, check for any ice stuck in the chute and remove it.
The fi rst batch of ice cubes may be small due to air in the pipe after connection, any air will be
purged during normal use.
When ICE OFF blinks on the display panel, -
CAUTION
reinsert the bucket and/or make sure it’s
installed properly.
When the door is open, the Ice and water dispenser do not work.
If you close the door hard, it may cause water spilling over the ice maker.
To prevent dropping the ice bucket, use both hands when removing it.
To prevent injury, be sure to clean up any ice or water that may have dropped on the fl oor.
Do not let the children hang on the ice dispenser or on the bucket. They may get hurt.
Be sure not to put your hand or any object into the ice chute. It may cause personal injury or damage
mechanical parts.
Figure2
Ice Chute
SETTING UP THE
REFRIGERATOR DOORS
If your entrance won’t allow the refrigerator to pass
easily through it, you can remove the doors.
Removing the Front Leg Cover
First, open both the freezer and refrigerator doors,
and then take off the front leg cover by turning the
three screws counter-clockwise.
Separating the Water Supply Line
from the Refrigerator
Remove two water lines (gray one is for ice and 1.
the other one is for water) by pressing the coupler
1
and pulling the water line 2 away.
Be careful that the water tube match same
color.
Reattaching the Water Supply Line
Water line must be fully inserted to the marked line 1.
to prevent water leakage and water dripping of
water dispenser.
Line
Coupler
Line
Coupler
01 SETTING UP
1
2
setting up _07setting up _07
DA99-01745T-EN.indd 07DA99-01745T-EN.indd 07 2011.6.27 3:28:51 PM2011.6.27 3:28:51 PM
Insert the 2 clips in the install pack and check that 2.
Coupler
clip A
(6.35mm)
clip A
(6.35mm)
- on some models
each clip holds the line fi rmly.
clip A
(6.35mm)
Coupler
Do not cut the water line. Gently separate it
from the coupler.
clip A
(6.35mm)
4
3
Removing the freezer door
A few things to mention fi rst.
Make sure that you lift the door straight up so the •
hinges are not bent or broken.
Be careful not to pinch the water tubing and wire •
harness on the door.
Place doors on a protected surface to prevent •
scratching or damage.
With the Freezer door closed, remove the upper 1.
hinge cover
disconnect the wires by gently pulling them apart
2
.
- on some models
1
using a screwdriver, and then
1
2
5
Be careful not to miss the parts of refrigerator.
Next, remove the door from the lower hinge 3.
carefully lifting the door straight up 7.
7
6
Be careful not to pinch the water tubing and
wire harness on the door.
Remove the lower hinge 4.
8
from the bracket 9
by gently lifting the lower hinge upwards.
6
by
Remove hinge screws 2.
4
by turning counter-clockwise, and take off the
upper hinge
5
3
and the ground screw
. Be careful that the door does not
fall on you as you are removing it.
8
9
08_ setting up08_ setting up
DA99-01745T-EN.indd 08DA99-01745T-EN.indd 08 2011.6.27 3:28:54 PM2011.6.27 3:28:54 PM
Reattaching the freezer doors
To reattach the freezer doors, assemble parts
in reverse order
Remove the lower hinge 4.
from the bracket
8
by gently
7
lifting the lower hinge upwards.
7
Removing the Fridge Door
With the door closed, remove the upper hinge 1.
1
cover
Remove hinge screws 2.
upper hinge 4. Be careful that the door does not
fall on you as you are removing it.
using a screwdriver.
1
2
3
by turning counter-clockwise, and take off the
2
3
and the ground screw
8
01 SETTING UP
Reattaching the Fridge door
To reattach the fridge doors, assemble parts
in reverse order.
LEVELLING THE
REFRIGERATOR
Now that the doors are back on the refrigerator, you
want to make sure the refrigerator is level so that
you can make fi nal adjustments. If the refrigerator
is not level, it will not be possible to get the doors
perfectly even.
The front of the refrigerator is also adjustable.
Before levelling the refrigerator,
remove the front leg cover
Open both the freezer and fridge doors, and then
take off the front leg cover by turning the three
screws counter-clockwise.
4
Be careful not to miss the parts of refrigerator.
Remove the door from the lower hinge 3.
5
by lifting
the door straight up 6.
6
5
setting up _09setting up _09
DA99-01745T-EN.indd 09DA99-01745T-EN.indd 09 2011.6.27 3:28:56 PM2011.6.27 3:28:56 PM
When the Freezer door is lower than
When the door of the freezer is
higher than the fridge
the fridge
Insert a fl at-blade screwdriver into a slot on the Leg,
turn it clockwise or counter clockwise to level the
freezer.
When the Freezer door is higher than
the fridge
Insert a fl at-blade screwdriver into a slot on the Leg,
turn it clockwise or counter clockwise to level the
fridge.
Screw Driver
Leg
When the door of the freezer is
higher than the fridge
Adjustment part
In the case of the process to correct the imbalance
is the same. Open the doors and adjust them, one
at a time, as follows:
1
Unscrew the nut 1.
from the lower hinge until it
reaches the upper end of the bolt 2 .
Wrench
3
2
Bolt
1
Nut
1
, make sure
, the door will
1
Leg
Screw Driver
Refer to the next section for the best way to
make very minor adjustments to the doors.
MAKING MINOR ADJUSTMENTS
TO THE DOORS
Remember, a levelling refrigerator is necessary
for getting the doors perfectly even. If you need
help, review the previous section on levelling the
refrigerator.
When you release the nut
that you use the Allen wrench provided 3
to loosen the bolt 2 in a counter-clockwise
direction. You should then be able to unscrew
the nut 1 with your fi ngers.
Adjust the height difference between the doors by 2.
turning the bolt
clockwise
2
clockwise or counter
.
When you turn clockwise
move up.
After adjusting the doors, turn the nut 3.
clockwise
until it reaches the lower end
of the bolt, then tighten the bolt again with the
wrench
3
to fi x the nut in place 1 .
If you do not secure the nut fi rmly, the bolt
may release.
10_ setting up10_ setting up
DA99-01745T-EN.indd 10DA99-01745T-EN.indd 10 2011.6.27 3:28:58 PM2011.6.27 3:28:58 PM
CHECKING THE WATER
Water line fi xer
and screws
Pipe connector
Water line
Clip
Water Filter
Close Main
Water pipe
Close Main
Water pipe
No gap
Remove
cap
Water Line
from unit
Water Line
from Kit
No gap
Loosen a
DISPENSER LINE
Close Main
Water pipe
A water dispenser is just one of the helpful features
on your new Samsung refrigerator. To help promote
better health, the Samsung water fi lter removes
unwanted particles from your water. However, it
does not sterilize or destroy microorganisms. You
will need to purchase a water purifying system to do
that.
In order for the icemaker to operate properly, water
pressure of 138 ~862 kPa is required. Under normal
conditions, a 170 cc paper cup can be fi lled in 10
seconds.
If the refrigerator is installed in an area with low water
pressure (below 138 kPa), you can install a booster
pump to compensate for the low pressure.
Make sure the water storage tank inside the
refrigerator is properly fi lled. To do this, press the
water dispenser lever until the water runs from the
water outlet.
Water Line installation Kits are included with
unit. You can fi nd it in freezer(or fridge) drawer.
Parts for water line Installation
Water line fi xer
1
and screws
Pipe connector
2
3
Water line
No gap
Close Main
Water pipe
After connecting the water supply to the water 4.
fi lter, turn your main water supply back on and
Dispense about 3L to clear and prime the water
fi lter.
INSTALLING THE WATER
DISPENSER LINE
Connecting the water line to the
refrigerator
Remove the cap from water line on the unit and 1.
insert compression nut to the water line on the
unit after disassembling from provided water line.
Connect both water line from the unit and water 2.
line in the kit
Tighten the compression nut onto the 3.
compression fi tting. Be careful no gap between
two items.
Turn water on and check for any leakage.4.
01 SETTING UP
Clip
4
Connecting to the water supply line
First, shut off the main water supply line.1.
Locate the nearest cold, drinking water line.2.
Follow the Water Line Installation Instructions in 3.
the installation kit.
CAUTION
The water line must be connected to
Water Filter
5
Loosen a
Water Line
from unit
Water Line
from Kit
Remove
cap
No gap
the cold water pipe.
If it is connected to the hot water pipe,
it may cause the purifi er to malfunction.
setting up _11setting up _11
DA99-01745T-EN.indd 11DA99-01745T-EN.indd 11 2011.6.27 3:29:0 PM2011.6.27 3:29:0 PM
Only connect the water line to a drinkable
Water
Ice
water source.
If you have to repair or disassemble the water line,
cut off 6.5mm of the plastic tubing to make sure you
get a snug, leak-free connection.
Before being used, the leakage in these
CAUTION
places should be examined
Samsung Warranty does not cover WATER LINE •
INSTALLATION.
It’ll be done at customer’s charge unless the retail •
price includes installation cost.
Please contact Plumber or Authorized Installer for •
the installation if needed.
If Water leakage occurs due to improper •
installation, Please contact installer.
Removing any residual matter inside
the water supply line after installing
fi lter.
Turn ON the main water supply.1.
Press the Water button and 2.
push the dispenser pad.
Run water through the 3.
dispenser until the water
runs clear (approx. 3L). This
will clean the water supply
system and remove air from
the lines.
Additional fl ushing may be 4.
required in some households.
Open the refrigerator door 5.
and make sure there are no
water leaks coming from the water fi lter.
A newly installed water fi lter cartridge may
cause water to briefl y spurt from the water
dispenser. This is due to air getting into the
line. It should pose no problem to operation.
12_ setting up12_ setting up
DA99-01745T-EN.indd 12DA99-01745T-EN.indd 12 2011.6.27 3:29:1 PM2011.6.27 3:29:1 PM
Water
Ice
operating the SAMSUNG sideby-side refrigerator
OPERATING THE
REFRIGERATOR
Using the Control Panel / Digital
Display
1
2
3
7 8
Speeds up the time needed to freeze products in
the freezer. This can be helpful if you need to quickly
1
Power
Freeze
Button
Freezer
Button
Ice Off
Button
Lighting
Button
Fridge
Button
Child Lock
Button
Ice Type
Button
Water
Button
freeze items that spoil easily or if the temperature in
the freezer has warmed dramatically (For example,
if the door was left open). This Function must
be activated before putting large stuff in freezer
compartment at least 24 hours before.
2
Press the Freezer button to set the freezer to your
desired temperature. You can set the temperature
between -14°C and -25ºC.
Press the Ice Off button to turn the ice making
function off.
3
When Ice Off blinks on the display panel, reinsert
the bucket and/or make sure it’s installed properly.
When you change the fi lter, press and hold this
button for 3 seconds to reset the fi lter schedule.
4
Press the Lighting button for the dispenser LED
lamp to stay on.
Press the Fridge button to set the fridge to your
5
desired temperature.
You can set temperature between 1°C ~ 7°C and
Power cool.
Power cool will be on the display after 1°C
By pressing this button, all buttons will be locked.
The Ice Type button and the dispenser pad will not
work either.
To cancel this function, press this button again.
6
If you are going on vacation or business trip or you
do not need to use the refrigerator, press and hold
this button for 3 seconds. The temperature in the
fridge will be around 15°C and the freezer will work
normally.
7
Press the Ice Type button to choose cubed or
crushed ice.
8
Press the Water button for water.
USING THE DIGITAL DISPLAY
“ Freezer Temp.” indicates the current Freezer
temperature.
“ Fridge Temp.” indicates the current Fridge
temperature.
When not in use the Display will turn off, this is
4
5
6
normal.
POWER FREEZE
This icon will light up when you activate the “Power
Freeze” feature. “Power Freeze” is great for times
when you need a lot of ice. When you have enough,
just press the button again to cancel the “Power
Freeze” mode.
When you use this function the energy
consumption of the refrigerator will increase.
Remember to turn it off when you don’t
need it and return the freezer to your original
temperature setting.
VACATION
This icon will light up when you activate the
“Vacation” feature.
If you are going on vacation or business trip or
you do not need to use the refrigerator, press and
hold the Child Lock button for 3 seconds. The
temperature in the fridge will be around 15°C and
the freezer will work normally. The refrigerator
section should be emptyed.
ALARM
This icon will light up all the time. The door alarm will
sound if any door is open for more than 2 minutes.
The beeping stops when you close the door. If
you need to turn off the Alarm function, press the
Lighting and Fridge buttons for 3 seconds at the
same time.
02 OPERATING
operating _13operating _13
DA99-01745T-EN.indd 13DA99-01745T-EN.indd 13 2011.6.27 3:29:1 PM2011.6.27 3:29:1 PM
LIGHTING
Exhibition
mode
This icon will light up when you activate the
“Lighting” feature. In this case, the dispenser light
(under the display) will be on constantly. If you would
like the dispenser light to come on only when using
the dispenser, turn the “Lighting” feature off.
CHILD LOCK
This icon will light up when you activate the Child
Lock function by pressing Child Lock button.
Press this button again to reactivate. Use this
function to prevent children from tampering with
temperature and fi lter settings.
POWER COOL
This icon will light up when you activate the “Power
Cool” feature.
For a quick fridge cool down, use “Power Cool”.
If you select “Power Cool”, the inside temperature
of the Fridge will decrease for about two and a half
hours.
FILTER INDICATOR
When the fi lter indicator light changes to red, it is
time to change the fi lter. Typically this happens about
every 6 months.
The fi lter Indicator will be Blue when you initially
insert the water fi lter.
The fi lter Indicator will be purple when you have
used your water fi lter for 5 months.
The fi lter Indicator will be Red when you have used
your water fi lter for 6 months.
After removing the old water fi lter and installing a
new one (see page 19 for instructions on how to do
this), reset the indicator status light by pressing the
Ice off button for about 3 seconds.
CUBED ICE , CRUSHED ICE
Enjoy cubed or crushed ice by selecting your
preference from the digital control panel. The ice
type light indicates the type of ice that is currently
chosen.
WATER
This icon will light up when you activate the “Water”
feature.
Canceling Exhibition Mode
In case of Exhibition Mode, It seems working
but doesn’t make cool air. To cancel this
CAUTION
mode, press the Power Freeze and Freezer
buttons at the same time for 8 seconds until
“Ding-dong” sounds.
Exhibition
mode
CONTROLLING THE
TEMPERATURE
Basic Temperature of Freezer and
Fridge
The basic and recommended temperature of Freezer
and Fridge compartments are -20ºC/3ºC.
If the temperature of Freezer and Fridge
compartments are too high or low, adjust the
temperature manually.
Controlling the Freezer temperature
The freezer temperature can be set between -14°C
and -25ºC to suit your particular needs. Press
the Freezer button repeatedly until the desired
temperature is shown in the temperature display.
Keep in mind that foods like ice cream may melt at
-16ºC.
ICE OFF
This icon will light up when you activate the “Ice Off”
feature. In this case, the ice will not be produced.
When Ice Off blinks on the display panel, reinsert
the bucket and/or make sure it’s installed properly.
14_ operating14_ operating
DA99-01745T-EN.indd 14DA99-01745T-EN.indd 14 2011.6.27 3:29:2 PM2011.6.27 3:29:2 PM
The temperature display will move sequentially from
Push
Ice Chute
Ice Bucket
Ice-Maker Cover
-14°C and -25ºC. When the display reaches -14ºC,
it will begin again at -25ºC.
Five seconds after the new temperature is set the
display will again show the actual current freezer
temperature. However, this number will change as
the Freezer adjusts to the new temperature.
Controlling the Fridge temperature
The refrigerator temperature can be set between
7ºC and 1ºC to suit your particular needs. Press
the Fridge button repeatedly until the desired
temperature is shown in the temperature display.
The temperature control process for the Fridge
works just like the Freezer process.
Press the Fridge button to set your desired
temperature. After a few seconds, the Fridge will
begin tracking towards the newly set temperature.
This will be refl ected in the digital display.
The temperature of the freezer or the refrigerator
may rise from opening the doors too frequently, or
if a large amount of warm or hot food is placed in
either side.
This may cause the digital display to blink. Once
the freezer and refrigerator return to their normal set
temperatures the blinking will stop.
If the blinking continues, you may need to “reset” the
refrigerator. Try unplugging the appliance, wait about
10 minutes and then plug back in.
USING THE ICE AND COLD
WATER DISPENSER
Using the Water Dispenser
Press the Water button. Place your cup the water
outlet and push gently against the dispenser pad.
Make sure the glass is in line with the dispenser to
prevent the water from splashing out.
To get cooler water
The dispensed water is cool, not icy cold
When you want colder water with -
Push
ice, dispense ice to your drink
glass fi rst before fi lling it with water
to prevent water from splashing
out.
Using the Ice Dispenser
Press the Ice Type button to select the type of ice
you want.
Place your cup the ice outlet and push gently
against the dispenser pad. Make sure the glass is
in line with the dispenser to prevent the ice from
bouncing out.
When Cubed Ice is selected after using the Crushed
Ice feature, a small amount of residual crushed ice
might be produced.
Do not put your fi ngers, hands or any •
WARNING
other unsuitable objects in the chute or
ice-maker bucket.
It may result in personal injury or material damage. Use only the ice maker provided with the •
refrigerator.
The water supply to this •
refrigerator must only be
installed/connected by a
suitably qualifi ed person
and connect to a potable
water supply only.
In order to operate the •
ice maker properly, water
pressure of 138 ~ 862 kPa
Ice Chute
is required.
Ice-Maker Cover
Ice Bucket
02 OPERATING
No Ice
Select this if you want to
turn the ice maker off.
When Ice Off blinks on the display panel, reinsert
the bucket and/or make sure it’s installed properly.
operating _15operating _15
DA99-01745T-EN.indd 15DA99-01745T-EN.indd 15 2011.6.27 3:29:3 PM2011.6.27 3:29:3 PM
CAUTION
GUARD FRE-UPP
(Optional)
GUARD FRE-BOTTOM
(Optional)
and won’t use water or ice dispensers,
close the water valve.
Otherwise, water leakage may occur. When you have not used the Ice maker for a while, •
or you have opened the Freezer door frequently,
the Ice may stick together. If this has occurred,
empty the ice container or break up the ice with a
wood kitchen tool.
Do not use sharp items such as knives or forks.
When the bucket is removed, there may still be some •
residual ice in the ice maker that will be produced.
If you have a long vacation or business trip •
1
For more space, you can
store food with Guard
FRE-UPP instead of the
ice bucket (
remove the ice bucket,
ICE OFF will blink on the
display panel.
For RSG5P & RSG5U
models,
1
). If you
GUARD FRE-UPP
(Optional)
To get more space, you
can remove the freezer
upper drawer since it does
not affect thermal and
mechanical charicteristics.
For RSG5F & RSG5D models,
GUARD FRE-BOTTOM
(Optional)
To get more space, you can remove the freezer
upper and lower drawers since it does not affect
thermal and mechanical charicteristics. But, put
the “Shelf Fre Bottom” on the bottom of the freezer
compartment. A declared storage volume of frozen
food storage compartment is calculated with the
drawer(s) removed.
The door guards in the freezer of this
model are the two star sections except the
top guard, so the temperature in two star
sections are slightly higher than other freezer
compartment.
16_ operating16_ operating
USING THE COOLSELECT
ZONE™ DRAWER (OPTIONAL)
The CoolSelect Zone™ Drawer is designed to make
your busy life just a little bit easier.
Soft Freeze
When “Soft Freeze” is selected on the CoolSelect
Zone™ Drawer, the temperature on the drawer
digital panel displays -5°C, regardless of the overall
temperature setting of the refrigerator.
This feature helps keep meat and fi sh
fresh for longer.
Chill
When “Chill” is selected, the temperature
of the CoolSelect Zone™ Drawer is
kept at -1°C, regardless of the overall
temperature setting of the refrigerator.
This feature also helps keep meat or fi sh
fresh for longer.
Thaw
When “Thaw” is selected, warm and cold
air is alternately blown into the CoolSelect Zone™
Drawer. Depending on the weight of the frozen food,
you can select a 4 hrs, 6 hrs, 10 hrs, and 12 hrs
thawing time.
When “Thaw” ends, food is in a half-frozen state,
making it easy to cut for cooking. In addition, when
“Thaw” ends, the CoolSelect Zone™ Drawer returns
to the original “Chill” condition. To cancel this
function mid-cycle, just press any button besides
Thaw.
Here are the approximate thawing times of meat
and fi sh by weight (and based on a 25.4mm (1in.)
thickness). This chart represents the total weight of
food in the CoolSelect Zone™ Drawer.
THAW TIME WEIGHT
4hours 363g (0.8Ib)
6hours 590g (1.3Ib)
10hours 771g (1.7Ib)
12hours 1000g (2.2Ib)
DA99-01745T-EN.indd 16DA99-01745T-EN.indd 16 2011.6.27 3:29:3 PM2011.6.27 3:29:3 PM
Quick Cool
You can use the “Quick Cool” operation with the
CoolSelect Zone™ Drawer to quickly cool 1~3
canned beverages in about an hour. When the
“Quick Cool” process ends, the CoolSelect Zone™
Drawer automatically returns to the previously set
temperature.
To cancel this operation, press the Quick Cool
button again and the CoolSelect Zone™ Drawer
returns to the previously set temperature.
Cool
When “Cool” is selected, the temperature in the
CoolSelect Zone™ Drawer will be the same as the
overall temperature setting of the refrigerator. The
drawer digital panel shows the same temperature
as that of the refrigerator display panel. Since the
“Cool” function mimics the refrigerator temperature,
you have extra general storage space.
Depending on the size and thickness of the
meat or fi sh, thawing times may vary.
When “Thaw” is in operation, any items that
you do not want affected should be moved
out of the drawer.
REMOVING THE FREEZER/
FRIDGE ACCESSORIES
Cleaning and rearranging the interior of the freezer
is a snap.
1. Shelves (Freezer/Fridge)
Remove the shelf by pulling the
shelf out to the hole point as
shown at the right fi gure. And
then remove it by turning and
lifting it up.
3. DRAWER
Remove the Drawer by pulling it
out and slightly lifting it up.
4. Ice Bucket (Freezer)
Remove the Icemaker Bucket
by lifting up and pulling it out
slowly.
Grip the handle as shown in •
the fi gure
Lift the low part slightly•
Take the ice bucket out •
slowly
5. Beverage Station (Fridge) (optional)
Lift up the upper bin at the •
top of the fridge and pull it
out.
After pressing the cover •
wrapped with both hands,
remove the beverage station
cover by pulling toward up.
Do not use excessive force when removing
the cover.
Otherwise, the cover may break and cause
injury.
Before removing any accessories, make sure
that no food is in the way.
When possible, remove the food altogether to
reduce the risk of accidents.
To get the best energy effi ciency of this
product, please leave all selves, drawers
and baskets on their original position like as
illustration in page (16)
CLEANING THE REFRIGERATOR
02 OPERATING
Do not use Benzene, Thinner or Clorox™ for
WARNING
2. DOOR BIN
Remove the Door Bin by
holding the door bin with both
hands and then gently lift it up.
DA99-01745T-EN.indd 17DA99-01745T-EN.indd 17 2011.6.27 3:29:4 PM2011.6.27 3:29:4 PM
cleaning.
They may damage the surface of the
appliance and can create a risk of fi re.
Do not spray the refrigerator with water while
CAUTION
it is plugged in, as it may cause an electric
shock. Do not clean the refrigerator with
benzene, thinner or car detergent for risk of
fi r e .
operating _17operating _17
CHANGING THE INTERIOR
Turn until the
label aligned.
Cover fi lter
Sticker
(month indicator)
LIGHTS
Changing the LED Type Lighting
Do not disassemble or replace the LED type
CAUTION
Lighting.
To change the LED Type Lighting contact Samsung
service center or your authorized Samsung dealer.
CHANGING THE WATER FILTER
To reduce risk of water damage to your
property DO NOT use generic brands of water
WARNING
fi lers in your SAMSUNG Refrigerator.
USE ONLY SAMSUNG BRAND WATER FILTERS.
SAMSUNG will not be legally responsible for any
damage, including, but not limited to property
damage caused by water leakage from use of a
generic water fi lter.
SAMSUNG Refrigerators are designed to work
ONLY WITH SAMSUNG Water Filter.
The “Filter Indicator” light lets you know when it is
time to change your water fi lter cartridge.
To give you preparation time to get a new fi lter, the
red light will come on just before the capacity of the
current fi lter runs out. Changing the fi lter on time
provides you with the freshest, cleanest water from
your fridge.
Remove the water fi lter from the box and 1.
put a month indicator sticker on the fi lter
as shown. Place a sticker on the fi lter
that dates six months in the future. For
example, if you are replacing the water
fi lter in March, put the “SEP” (September)
sticker on the fi lter to remind you to
replace in September. Normal fi lter life is
about every 6 months.
Remove the new fi lter’s protective cap and remove 2.
the old fi lter.
Position and insert the new fi lter into the fi lter 3.
housing. Slowly turn the water fi lter clockwise to
align with the printing mark on the cover, locking
the fi lter in position. Make sure to align the water
fi lter label mark with the center of cover fi lter
printing as illustrated. Remember, do not overtighten.
Cover fi lter
123
Sticker
(month indicator)
Turn until the
label aligned.
Once you have completed this process, hold the 4.
Ice Off button simultaneously for 3 seconds to
reset the fi lter schedule.
Lastly, run about 3L of water through water 5.
dispenser and throw away. Make sure that water
fl ows clearly again before drinking.
See installing the water fi lter instructions page 11.6.
A newly installed water fi lter cartridge may cause
water to briefl y spurt from the water dispenser. This
is due to air getting into the line. It should pose no
problem to operation.
Ordering replacement fi lters
To order more water fi lter cartridges, contact your
authorized Samsung dealer.
USING THE DOORS
The refrigerator doors are equipped with a door
opening and closing feature that ensures that the
doors close all the way and are securely sealed.
After opening beyond a certain point, the door will
“catch” and remain open. When the door is ajar
ahead of the catch that allows it to stay open, it will
close automatically.
18_ operating18_ operating
DA99-01745T-EN.indd 18DA99-01745T-EN.indd 18 2011.6.27 3:29:5 PM2011.6.27 3:29:5 PM
troubleshooting
PROBLEM SOLUTION
The refrigerator does not
work at all or it does not
chill suffi ciently.
The food in the fridge is
frozen.
You hear unusual noises
or sounds.
The front corners of
the appliance are hot
and condensation is
occurring.
Ice is not dispensing. Did you wait for 12 hours after installation of the water supply line before •
You can hear water
bubbling in the
refrigerator.
There is a bad smell in the
refrigerator.
Frost forms on the walls
of the freezer.
Water dispenser is not
functioning.
Check that the power plug is properly connected.•
Is the temperature control on the display panel set to the correct •
temperature? Try setting it to a lower temperature.
Is the refrigerator in direct sunlight or located too near a heat source?•
Is the back of the refrigerator too close to the wall and therefore keeping •
air from circulating?
Is the temperature control on the display panel set to the correct •
temperature? Try setting it to a warmer temperature.
Is the temperature in the room very low?•
Did you store the food with a high water content in the coldest part of •
the fridge? Try moving those items into the body of the fridge instead of
keeping them in the CoolSelect Zone™ drawer.
Check that the refrigerator is level and stable.•
Is the back of the refrigerator too close to the wall and therefore keeping •
air from circulating?
Was anything dropped behind or under the refrigerator?•
A “ticking” sound is heard from inside the refrigerator. This is normal and •
occurs because various accessories are contracting or expanding in
relation to the temperature of the refrigerator interior.
Some heat is normal as anti-condensators are installed in the front corners •
of the refrigerator to prevent condensation.
Is the refrigerator door ajar? Condensation can occur when you leave the •
door open for a long time.
making ice?
Is the water line connected and the shut-off valve open?•
Did you manually stop the ice making function? Make sure Ice Type is set •
to Cubed or Crushed.
Is there any ice blocked within the ice maker bucket?•
Is the freezer temperature too warm? Try setting the freezer temperature •
lower.
This is normal. The bubbling comes from the refrigerant coolant liquid •
circulating through the refrigerator.
Has a food item spoiled?•
Make sure that strong smelling food (for example, fi sh) is wrapped so that •
it is airtight.
Clean out your freezer periodically and throw away any spoiled or suspect •
food.
Is the air vent blocked? Remove any obstructions so air can circulate •
freely.
Allow suffi cient space between the foods stored for effi cient air circulation.•
Is the freezer door closed properly?•
Is the water line connected and the shut-off valve open?•
Has the water supply line tubing been crushed or kinked?•
Make sure the tubing is free and clear of any obstruction.
Is the water tank frozen because the refrigerator temperature is too low?•
Try selecting a warmer setting on the main display panel.
03 TROUBLESHOOTING
troubleshooting _19troubleshooting _19
DA99-01745T-EN.indd 19DA99-01745T-EN.indd 19 2011.6.27 3:29:5 PM2011.6.27 3:29:5 PM
Ambient Room Temperature Limits
This fridge/freezer is designed to operate in ambient temperatures specifi ed by its temperature class marked
on the rating plate.
Class Symbol Ambient Temperature range(°C)
Extended Temperate SN +10 to +32
Temperate N +16 to +32
Subtropical ST +16 to +38
Tropical T +16 to +43
Internal temperatures may be affected by such factors as the location of the fridge/freezer, ambient
temperature and the frequency with which you open the door. Adjust the temperature as required to
compensate for these factors.
Correct Disposal of This Product
English
(Applicable in the European Union and other European countries with separate collection systems)
This marking on the product, accessories or literature indicates that the product and its electronic accessories
(e.g. charger, headset, USB cable) should not be disposed of with other household waste at the end of their
working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal,
please separate these items from other types of waste and recycle them responsibly to promote the sustainable
reuse of material resources.
Household users should contact either the retailer where they purchased this product, or their local government
offi ce, for details of where and how they can take these items for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of the purchase contract. This
product and its electronic accessories should not be mixed with other commercial wastes for disposal.
(Waste Electrical & Electronic Equipment)
Contact SAMSUNG WORLD WIDE
If you have any questions or comments relating to Samsung products, please contact
the SAMSUNG customer care center.
COUNTRY CALL Web site
AUSTRALIA 1300 362 603 www.samsung.com/au
COLOMBIA 01-8000112112 www.samsung.com/co
EIRE 0818 717 100 www.samsung.com/ie
HONG KONG (852) 3698-4698
INDIA 3030 8282, 1-800-3000-8282 www.samsung.com/in
MALAYSIA 1800-88-9999 www.samsung.com/my
NEW ZEALAND 0800 SAMSUNG (726-7864) www.samsung.com/nz
PANAMA 800-7267 www.samsung.com/latin
PHILIPPINES 1800-10-SAMSUNG (726-7864) www.samsung.com/ph
SINGAPORE 1800-SAMSUNG (726-7864) www.samsung.com
SOUTH AFRICA 0860-SAMSUNG (726-7864 ) www.samsung.com
U.K 0330 SAMSUNG (726-7864) www.samsung.com
VIETNAM 1 800 588 889 www.samsung.com
www.samsung.com/hk
www.samsung.com/hk_en/
Code No. DA99-01745T REV(0.6)
DA99-01745T-EN.indd 20DA99-01745T-EN.indd 20 2011.6.27 3:29:6 PM2011.6.27 3:29:6 PM
Loading...