Samsung SyncMaster 570BTFT, RN15MSS, SyncMaster 580BTFT, RN15MOT, RN15MST Service Manual

COLOR MONITOR

SyncMaster 570BTFT
SyncMaster 580BTFT
(RN15MSS / RN15MST

RN15MOS / RN15MOT)

Manual

SERVICE

COLOR MONITOR CONTENTS

EXIT MENUAUTO EXIT MENUAUTO

1. Precautions

2. Product Specifications

3. Disassembly & Reassembly

4. Troubleshooting

5. Exploded View & Parts List

6. Electrical Parts List

7. Block Diagram

8. Wiring Diagram

9. Schematic Diagrams

1-1-1 Warnings

1. For continued safety, do not attempt to modify the
circuit board.

2. Disconnect the AC power and DC Power Jack
before servicing.

3. When the chassis is operating, semiconductor
heatsinks are potential shock hazards.

1-1-2 Servicing the LCD Monitor

1. When servicing the LCD Monitor, remove the static
charge by connecting a 10k ohm resistor in series
with an insulated wire (such as a test probe)
between the chassis and the anode lead.
(Disconnect the AC line cord from the AC outlet.)

2. It is essential that service technicians have an
accurate voltage meter available at all times. Check
the calibration of this meter periodically.

1-1-3 Fire and Shock Hazard

Before returning the monitor to the user, perform the
following safety checks:

1. Inspect each lead dress to make certain that the
leads are not pinched or that hardware is not
lodged between the chassis and other metal parts in
the monitor.

2. Inspect all protective devices such as nonmetallic
control knobs, insulating materials, cabinet backs,
adjustment and compartment covers or shields,
isolation resistor-capacitor networks, mechanical
insulators, etc.

3. Leakage Current Hot Check (Figure 1-1): WARNING:

Do not use an isolation transformer during this test.

Use a leakage current tester or a metering system
that complies with American National Standards
Institute (ANSI C101.1, Leakage Current for

Appliances), and Underwriters Laboratories (UL
Publication UL1410, 59.7).

Figure 1-1. Leakage Current Test Circuit

4. With the unit completely reassembled, plug the AC
line cord directly into a 120V AC outlet. With the
unit’s AC switch first in the ON position and then
OFF, measure the current between a known earth
ground (metal water pipe, conduit, etc.) and all
exposed metal parts, including: metal cabinets,
screwheads and control shafts. The current
measured should not exceed 0.5 milliamp. Reverse
the power-plug prongs in the AC outlet and repeat

the test.

1-1-4 Product Safety Notices

Some electrical and mechanical parts have special
safety-related characteristics which are often not
evident from visual inspection. The protection they give
may not be obtained by replacing them with
components rated for higher voltage, wattage, etc. Parts
that have special safety characteristics are identified by

on schematics and parts lists. A substitute
replacement that does not have the same safety
characteristics as the recommended replacement part
might create shock, fire and / or other hazards. Product
safety is under review continuously and new
instructions are issued whenever appropriate.

SyncMaster 570BTFT / 580BTFT 1-1

1 Precautions

Follow these safety, servicing and ESD precautions to prevent damage and to protect against potential hazards such as
electrical shock.

1-1 Safety Precautions

DEVICE
UNDER
TEST

TEST ALL

EXPOSED METAL

SURFACES

(READING SHOULD

NOT BE ABOVE 0.5mA)

LEAKAGE
CURRENT

TESTER

2-WIRE CORD

ALSO TEST WITH

PLUG REVERSED
(USING AC ADAPTER
PLUG AS REQUIRED)

EARTH

GROUND

!

1-2-1 General Servicing Precautions

1. Always unplug the unit’s AC power cord from the
AC power source and disconnect the DC Power
Jack before attempting to:
(a) remove or reinstall any component or assembly,
(b) disconnect PCB plugs or connectors, (c) connect
a test component in parallel with an electrolytic
capacitor.

2. Some components are raised above the printed
circuit board for safety. An insulation tube or tape
is sometimes used. The internal wiring is
sometimes clamped to prevent contact with
thermally hot components. Reinstall all such
elements to their original position.

3. After servicing, always check that the screws,
components and wiring have been correctly
reinstalled. Make sure that the area around the
serviced part has not been damaged.

1. Immediately before handling any semiconductor
components or assemblies, drain the electrostatic
charge from your body by touching a known earth
ground. Alternatively, wear a discharging wrist­strap device. To avoid a shock hazard, be sure to
remove the wrist strap before applying power to
the monitor.

2. After removing an ESD-equipped assembly, place it
on a conductive surface such as aluminum foil to
prevent accumulation of an electrostatic charge.

3. Do not use freon-propelled chemicals. These can
generate electrical charges sufficient to damage
ESDs.

4. Use only a grounded-tip soldering iron to solder or
desolder ESDs.

5. Use only an anti-static solder removal device. Some
solder removal devices not classified as “anti-static”
can generate electrical charges sufficient to damage
ESDs.

4. Check the insulation between the blades of the AC
plug and accessible conductive parts (examples:
metal panels, input terminals and earphone jacks).

5. Insulation Checking Procedure: Disconnect the
power cord from the AC source and turn the power
switch ON. Connect an insulation resistance meter
(500 V) to the blades of the AC plug.

The insulation resistance between each blade of the
AC plug and accessible conductive parts (see
above) should be greater than 1 megohm.

6. Always connect a test instrument’s ground lead to
the instrument chassis ground before connecting the
positive lead; always remove the instrument’s
ground lead last.

6. Do not remove a replacement ESD from its
protective package until you are ready to install it.
Most replacement ESDs are packaged with leads
that are electrically shorted together by conductive
foam, aluminum foil or other conductive materials.

7. Immediately before removing the protective
material from the leads of a replacement ESD,
touch the protective material to the chassis or
circuit assembly into which the device will be
installed.

Caution: Be sure no power is applied to the

chassis or circuit and observe all
other safety precautions.

8. Minimize body motions when handling
unpackaged replacement ESDs. Motions such as
brushing clothes together, or lifting your foot from
a carpeted floor can generate enough static
electricity to damage an ESD.

1 Precautions

1-2 SyncMaster 570BTFT / 580BTFT

1-3 Electrostatically Sensitive Devices (ESD) Precautions

Some semiconductor (solid state) devices can be easily damaged by static electricity. Such components are commonly
called Electrostatically Sensitive Devices (ESD). Examples of typical ESD devices are integrated circuits and some field­effect transistors. The following techniques will reduce the incidence of component damage caused by static electricity.

1-2 Servicing Precautions

WARNING: An electrolytic capacitor installed with the wrong polarity might explode.

Caution: Before servicing units covered by this service manual, read and follow the Safety Precautions

section of this manual.

Note: If unforeseen circumstances create conflict between the following servicing precautions and any of the

safety precautions, always follow the safety precautions.

2 Product Specifications

2-1 Specifications

LCD Panel TFT-LCD panel, RGB vertical stripe, normaly white, 15-Inch viewable,

0.297 (H) x 0.297 (V) pixel pitch

Scanning Frequency Horizontal : 30 kHz to 61 kHz (Automatic)

Vertical : 50 Hz to 75 Hz (Automatic)

Display Colors 16,772,216 colors

Maximum Resolution Horizontal : 1024 Pixels

Vertical : 768 Pixels

Input Video Signal Analog, 0.714 Vp-p ± 5% positive at 75 Ω, internally terminated

Input Sync Signal Type: Seperate H/V sync, Composite H/V, Sync-on-Green, automatic synchronization

without external switch of sync type

Level: TTL level

Maximum Pixel Clock rate 80 MHz

Active Display 304.1 mm / 228.1 mm
Horizontal/Vertical

AC power voltage & Frequency AC 90 to 264 Volts, 60/ 50 Hz ± 3 Hz

Power Consumption 25 W (max.)

Dimensions
Unit (W x D x H) 15.9x7.7x16.5 Inches (404 x 196 x 419 mm)

Carton (W x D x H) 18.7 x 11.1 x 20.1 Inches (475 x 282 x 510 mm)

Weight (Net/Gross) 7.4 kg / 9.4kg

Environmental Considerations Operating Temperature : 50°F to 104°F (10°C to 40°C)

Humidity : 10 % to 80 %

Storage Temperature : -13°F to 113°F (-25°C to 45°C)
Humidity : 5 % to 95 %

Audio Characteristics • Audio Characteristics

(optional) • Built-in Microphone: High-sensitivity condenser microphone (mono)

• Audio input: Left/Right Stereo phone jack, 0.7 Vrms

• Sound output: 16 W (left) + 16 W (right)/THD 1% at 16ohm

• Frequency response: 80 Hz~20 kHz (at –3dB)

• Headphone: Max 50mW output (3.5-pi jack)

• Speaker: Internal semi Dome (16ohm x 2)

• SyncMaster 570BTFT/580BTFT complies with SWEDAC (MPR II) recommendations for reduced electromagnetic fields.

• Designs and specifications are subject to change without prior notice.

SyncMaster 570BTFT / 580BTFT 2-1

Item Description

16 ~26 GND GND GND

2 Product Specifications

2-2 SyncMaster 570BTFT / 580BTFT

2-2 Pin Assignments

Sync
Type

Pin No.

15-Pin Signal Cable Connector

Separate Composite Sync-on-green

Sync-on-green

1
2
3
4
5
6
7
8

9
10
11
12
13
14
15

Red
Green
Blue
GND
GND (DDC Return)
GND-R
GND-G
GND-B
No Connection
GND-Sync/Self Test
GND
DDC Data
H-Sync
V-Sync
DDC Clock

Red
Green
Blue
GND
GND (DDC Return)
GND-R
GND-G
GND-B
No Connection
GND-Sync/Self Test
GND
DDC Data
H/V-Sync
Not Used
DDC Clock

Red
Green + H/V Sync
Blue
GND
GND (DDC Return)
GND-R
GND-G
GND-B
Not Used
GND-Sync/Self Test
GND
DDC Data
Not Used
Not Used
DDC Clock

Sync
Type

Pin No.

26-Pin Signal Cable Connector

Separate Composite

1

2

3

4

5

6

7

8

9
10
11
12
13
14
15

Red
Green
Blue
GND
GND (DDC Return)
GND-R
GND-G
GND-B
No Connection
GND-Sync/Self Test
GND
DDC Data
H-Sync
V-Sync
DDC Clock

Red
Green
Blue
GND
GND (DDC Return)
GND-R
GND-G
GND-B
No Connection
GND-Sync/Self Test
GND
DDC Data
H/V-Sync
Not Used
DDC Clock

Red
Green + H/V Sync
Blue
GND
GND (DDC Return)
GND-R
GND-G
GND-B
Not Used
GND-Sync/Self Test
GND
DDC Data
Not Used
Not Used
DDC Clock

31.469

31.778

3.813

1.589

26.058

0.318

70.086

14.268

0.064

1.716

11.504

0.985

25.175

Positive

Negative

Separate

fH (kHz)

A µsec

B µsec

C µsec

D µsec

E µsec

fV (Hz)

O msec

P msec

Q msec

R msec

S msec

Clock
Frequency
(MHz)

Polarity
H.Sync

V.Sync

Remark

IBM

2 Product Specifications

SyncMaster 570BTFT / 580BTFT 2-3

QRS

P

O

Video

Sync

Sync

Horizontal

Vertical

CDE

P

O

B

A

Video

Sync

Sync

Separate Sync

2-3 Timing Chart

This section of the service manual describes the timing that the computer industry recognizes as standard
for computer-generated video signals.

C D

A

O

E

B

P

Video

Sync

Sync

Video

Q R S

A : Line time total B : Horizontal sync width O : Frame time total P : Vertical sync width

C : Back porch D : Active time Q : Back porch R : Active time

E : Front porch S : Front porch

VGA3/60 Hz

640 x 480

640/72 Hz

640 x 480

640/75 Hz

640 x 480

800/56 Hz

800 x 600

800/60 Hz

800 x 600

VGA1/70 Hz

640 x 350

VGA2/70 Hz

720 x 400

Table 2-1. Timing Chart

31.469

31.777

3.813

1.589

26.058

0.318

70.087

14.268

0.064

0.858

13.155

0.191

28.322

Negative

Positive

Separate

31.469

31.778

3.813

1.589

26.058

0.318

59.940

16.683

0.064

0.794

15.761

0.064

25.175

Negative

Negative

Separate

37.861

26.413

1.270

3.810

20.825

0.508

72.809

13.735

0.079

0.528

13.100

0.026

31.500

Negative

Negative

Separate

37.500

26.667

2.032

3.810

20.317

0.508

75.000

13.333

0.080

0.427

12.800

0.027

31.500

Negative

Negative

Separate

35.156

28.444

2.000

3.556

22.222

0.667

56.250

17.778

0.057

0.626

17.067

0.028

36.000

Positive

Negative

Separate

37.879

26.400

3.200

2.200

20.000

1.000

60.317

16.579

0.106

0.607

15.840

0.026

40.000

Positive

Positive

Separate

Mode

VESA

Timing

2 Product Specifications

2-4 SyncMaster 570BTFT / 580BTFT

48.077

20.800

2.400

1.280

16.000

1.120

72.188

13.853

0.125

0.478

12.480

0.770

50.000

Positive

Positive

Separate

fH (kHz)

A µsec

B µsec

C µsec

D µsec

E µsec

fV (Hz)

O msec

P msec

Q msec

R msec

S msec

Clock
Frequency
(MHz)

Polarity
H.Sync

V.Sync

Remark

VESA

1024/60 Hz

1024 x 768

1024/70 Hz

1024 x 768

1024/75 Hz

1024 x 768

640/67 Hz

60 x 480

832/75 Hz

832 x 624

800/72 Hz

800 x 600

800/75 Hz

800 x 600

Table 2-1. Timing Chart Continued

46.875

21.333

1.616

3.232

16.162

0.323

75.000

13.333

0.064

0.448

12.800

0.021

49.500

Positive

Positive

Separate

48.363

20.677

2.092

2.462

15.754

0.369

60.004

16.666

0.124

0.600

15.880

0.062

65.000

Negative

Negative

Separate

56.476

17.707

1.813

1.920

13.653

0.320

70.069

14.272

0.106

0.513

13.599

0.053

75.000

Negative

Negative

Separate

60.023

16.660

1.219

2.235

13.003

0.203

75.029

13.328

0.050

0.466

12.795

0.017

78.750

Positive

Positive

Separate

35.000

28.571

2.116

3.175

21.164

2.116

66.667

15.000

0.086

1.114

13.714

0.086

30.240

Negative

Negative

Separate

49.726

20.110

1.117

3.910

14.524

0.559

74.551

13.414

0.060

0.784

12.549

0.020

57.284

Negative

Negative

Separate

Mode

MAC.

Timing

QRS

P

O

Video

Sync

Sync

Horizontal

Vertical

CDE

P

O

B

A

Video

Sync

Sync

Separate Sync

C D

A

O

E

B

P

Video

Sync

Sync

Video

Q R S

A : Line time total B : Horizontal sync width O : Frame time total P : Vertical sync width

C : Back porch D : Active time Q : Back porch R : Active time

E : Front porch S : Front porch

3-1-1 Removing the Stand

1. Remove 4 screws in the hinge area.

2. Pry it off the back of the monitor.

3. Disconnect Power Cord and Signal Cable.

3-1-2 Main Body Disassembly

1. Remove the 4 screws on the four corner of the
Rear Cover.

2. Remove Rear Cover from the Front Cover.

3. Remove 11 screws on the Shield and remove
the shield.

4. Disconnect Inverter wire, Function PCB wire
and Interface wire.
Remove 4 screws on the Main PCB and
remove 2 screws on the D sub shield.

5. Remove the Main PCB Assembly.

6. Remove 6 screws on the Inverter PCB
Assembly and then remove it

7. Remove 6 screws on the Rear Panel Bracket.

8. Remove the Bracket Assembly from the Front
Cover.

9. Remove 3 screws on the Function PCB from
locking area of Function knob and remove
Function PCB.

10. Remove 4 screws on the Shield of Panel.

11. Remove the Shield.

12. Remove Rear Bracket from Panel.

13. Remove 2 screws between Panel Rear and
Inverter PCB.

14. Remove the Interface wire on the Rear Side of
Panel.

3-1-3 Standard Stand Disassembly

1. Remove 5 screws from the Stand Rear

2. Remove 4 screws from the Stand Bottom.

3. Remove Stand Front from the Stand assembly.

4. Remove 2 screws from the Stand assembly.

5. Remove the Stand Rear from the Stand
assembly.

6. Remove 5 screws on the Vesa Brkt from the
Stand assembly.

7. Remove cover hinge from the Stand assembly.

8. Remove Stand Base from the Stand assembly.

3-1-4 Pivot Multi-media Stand Disassembly

(option)

1. Stand the stand assembly with the base close
to you.

2. Remove the 4 screws on the back cover of the
stand and remove it.

3. Stand the stand assembly upside down.

4. Remove the 4 screws.

5. Disconnect CN805, CN806, CN807, CN808,
CN809, CN812 and F1.

6. Remove the Back Cover of the Stand Front
assembly.

7. Remove 4 screws on the external adaptor and
remove the adaptor.

8. Remove 2 screws between hinge and Stand
Body.

9. Remove the hinge

10. Remove 2 screws on Audio main PCB and
remove it

11. Remove 2 screws on the Audio Function PCB
and remove it.

3-1-5 Angle Pivot Stand Disassembly (option)

1. Remove the cap pivot from the stand
assembly.

2. Remove the 4 screws on the hinge assembly.

3. Remove the 4 screws on the Stand Rear

SyncMaster 570BTFT / 580BTFT 3-1

3 Disassembly and Reassembly

This section of the service manual describes the disassembly and reassembly procedures for the
SyncMaster 570BTFT/580BTFT monitors.

WARNING: This monitor contains electrostatically sensitive devices. Use caution when handling

these components.

3-1 Disassembly

Cautions:1. Disconnect the monitor from the power source before disassembly.

2. Follow these directions carefully; never use metal instruments to pry apart the cabinet.

4. Remove the Stand Rear from the Stand
assembly.

5. Remove the Stand Front from the Stand
assembly.

6. Remove the Neck Rear from the Stand
assembly.

7. Remove the 4 Rubbers on the four corner of
the Stand Bottom and the 4 screws on the four
corner of the Stand Bottom.

8. Remove the 5 stopper hings from the Bracket
Bottom.

9. Remove the Stand Base from the Stand
Assembly.

3-1-6 Wire frame stand Disassembly (option)

1. Carefully pull the cover hinge.

2. Remove the cover vesa from the Stand
assembly.

3. Remove 4 screws on the assembly Bracket
assembly.

3 Disassembly and Reassembly

3-2 SyncMaster 570BTFT / 580BTFT

3-2 Replacement Order of Lamp Assemblies

- RN15MSS/RM15MOS (Samsung Panel)

3 Disassembly and Reassembly

SyncMaster 570BTFT / 580BTFT 3-3

3 Disassembly and Reassembly

3-4 SyncMaster 570BTFT / 580BTFT

2. Push down the stopper and
slide the lamp unit.

3. Please take out the lamp
units from the LCD module.

3-3 Replacement Order of Lamp Assemblies

- RN15MST/RM15SOT (Toshiba Panel)

1. After confirm there is nothing
on the desk
Turn the LCD module over
and put it on a flat desk set to
the ground.

3 Disassembly and Reassembly

SyncMaster 570BTFT / 580BTFT 3-5

4. Please fix the new lamp
units on the LCD module :
opposite process 2 and 3

* Replacement of lamp unit should be done at the power off state and rcommended clean bench

condition.

3-4 Reassembly

Reassembly procedures are in the reverse order of Disassembly procedures.

Memo

3 Disassembly and Reassembly

3-6 SyncMaster 570BTFT / 580BTFT

SyncMaster 570BTFT/580BTFT 4-1

4 Troubleshooting

Notes: 1. Before troubleshooting, setup the PC’s display as below.

• Resolution: 1024 x 768

• H-frequency: 48 kHz

• V-frequency: 60 Hz

2. If no picture appears, make sure the power cord is correctly connected.

3. Check the following circuits.

• No raster appears: Audio PCB, SMPS PCB, Main PCB

• 12V develop but no screen: Main PCB

• 12V does not develop: Audio PCB, SMPS PCB

4. If you push and hold the “EXIT” button for more than 5 seconds, the monitor automatically turns back
to the factory preset.

4-1 No Power

Does proper DC 12 V appear at

DC jack connected to CN102?

Check SMPS PCB and CN816.

Yes

No

Does proper DC 5 V appear at

Pin 3 of IC109?

Check FT100 and IC109.

Check IC401, IC111, Q101 and Q102.

Yes

No

4 Troubleshooting

4-2 SyncMaster 570BTFT/580BTFT

4-2 No Video

Replace IC101.

Power indicator is green

Replace IC305 or check its

related circuit.

Replace IC310 and IC311 or

check its related circuits.

Replace IC106.

Replace IC104 (SOG)

or IC105 (seperate sync.

Check IC101 and IC401.

No

Does the clock pulse

appear at output of

R190, R191, R193?

Does the H-sync pulse appear

at Pin 94 of IC101?

Does the pulse appear at Pin 10

of IC105 or Pin 1 of IC104?

7 8 9

No

Does the sync pulses appear at

Pins 20 and 22 of IC192?

Does the sync pulses appear at

Pins 34 and 39 of IC192?

Replace IC192 or check its

related circuit.

18 19 20 1

Replace IC301 or check its

related circuit.

Replace LCD Panel

No

Do the sync pulses appear at

Pins 22, 23, 25 and 26 of IC310?

Do the sync pulses appear at Pins

2, 3, 54, 55 and 56 of IC301?

2 3 4 5 10 11 12 13 14

No

Do the waveforms appear at

Pins 5 and 20 of CN301?

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

No

No

No

No

6

4 Troubleshooting

SyncMaster 570BTFT/580BTFT 4-3

WAVEFORMS

2

IC310 #22

CH1 RMS = 3.1 V

3

IC310 #23

CH1 RMS = 2.3 V

4

IC310 #25

CH1 RMS = 2.8 V

5

IC310 #26

CH1 RMS = 2.12 V

6

CN301 #5~20

CH1 RMS = 1.18 V

7

IC101 #94

CH1 RMS = 3.5 V

8

IC105 #10

CH1 RMS = 3.1 V

9

IC104, #1

CH1 RMS = 4.56 V

10

IC301 #2

CH1 RMS = 2.3 V

11

IC301 #3

CH1 RMS = 3.25 V

12

IC301 #54

CH1 RMS = 2.35 V

13

IC301, #55

CH1 RMS = 200 mV

14

IC301 #56

CH1 RMS = 50 mV

18

IC192 #20

CH1 RMS = 1.24 V

19

IC192 #22

CH1 RMS = 400 mV

20

IC192 #34

CH1 RMS = 4.4 V

1

IC192 #39

CH1 RMS = 3.6 V

4 Troubleshooting

4-4 SyncMaster 570BTFT/580BTFT

4-3 No Video of Alternate Vertical Line

One or more even or odd vertical lines do not display.

Does the waveform appear

at Pin 20 of CN301?

Replace IC311 or check its

related circuit.

Replace LCD panel.

Yes

No

6

WAVEFORMS

Go to 4-4 No OSD Display.

4-5 User Controls Don’t Work

Check the buttons.
(SW861 ~ SW866)

Does the DC level change at

Pins 11 and 12 of IC401 when you

push the front panel button?

Yes

No

Replace IC305.

Yes Yes

No

There is video but no OSD.

Replace IC307 or check its

related circuit.

Replace IC305.

4-4 No OSD

While pushing a front control
button does any pulse appear

at Pin 12 of IC307?

No

Do sync signals appear at Pins 5

and 10 of IC307?

15

16

17

WAVEFORMS

6

CN301 #20

CH1 RMS = 1.18 V

15

IC307 #12

CH1 RMS = 2.2 V

16

IC307 #5

CH1 RMS = 1.7 V

17

IC307 #10

CH1 RMS = 4.3 V

4 Troubleshooting

SyncMaster 570BTFT/580BTFT 4-5

4-6 No Sound

Check IC803, IC804, VR841 and

related circuit.

Check Pins 1 and 2 of CN806 and

related circuits.

Does the DC 5 V appear at Pin

4 of IC803, Pin 5 of CN806?

Does the sound input signal

appear at Pins 6 and 11 of IC803?

Yes

No

Yes

No

Check IC803 and related circuits.

Do the sound signals appear at

Pins 3 and 14 of IC803?

Yes

No

Check C815, CN813, R821, R822,

ZD803 on the Audio PCB.

Check CN814, CN815 outputs.

Does the DC 2.5 V bias appear at

Pin 16 of IC503?

Yes

No

4 Troubleshooting

4-6 SyncMaster 570BTFT/580BTFT

4-8 Headphones Don’t Work

Check the Headphone Plug in the

Headphone Jack and R821, R822,

C815 on the Audio PCB.

Check CN813 on the Audio PCB

and related circuit R817, R820,

ZD801, ZD802.

OK

Can you hear any sound from

the Headphones?

Do you hear sound from the

Internal Speaker?

Yes

Yes

No

No

4-7 Microphones Don’t Work

Check the PC’s sound program

and compatibility.

Connect the cable between the PC

and monitor.

Does the PC’s sound

program operate well?

Is the connection between the PC

and monitor secure?

Yes

No

Yes

No

Check the connection between

CN805 on the Audio PCB and the

Internal Microphone.

Is the Internal Microphone

connector attached?

Yes

No

Check Q802 and related circuits.

Does the Internal Microphone

work?

Yes

No

Check the CN182 jack.

OK

Does the External Microphone

work?

Yes

No

5 Exploded View & Parts List

5-2 Multimedia Pivot-base RN15MST (TOSHIBA PANEL)

5 Exploded View & Parts List

5-4 Multimedia-base RN15MST (TOSHIBA PANEL)

5 Exploded View & Parts List

5-6 Pivot-base RN15MST (TOSHIBA PANEL)

5 Exploded View & Parts List

5-8 Simple-base RN15MST (TOSHIBA PANEL)

5 Exploded View & Parts List

5-10 Wire frame-base RN15MST (TOSHIBA PANEL)

BD101 2703-001334 INDUCTOR-SMD 1.5uH,10%,2x1.25x0.85mm
BD102 2703-001334 INDUCTOR-SMD 1.5uH,10%,2x1.25x0.85mm
BD103 2703-001334 INDUCTOR-SMD 1.5uH,10%,2x1.25x0.85mm
BD104 2703-001334 INDUCTOR-SMD 1.5uH,10%,2x1.25x0.85mm
BD105 2703-001334 INDUCTOR-SMD 1.5uH,10%,2x1.25x0.85mm
BD401 2703-001334 INDUCTOR-SMD 1.5uH,10%,2x1.25x0.85mm
BD402 2703-001334 INDUCTOR-SMD 1.5uH,10%,2x1.25x0.85mm
BD403 2703-001334 INDUCTOR-SMD 1.5uH,10%,2x1.25x0.85mm
BD404 2703-001334 INDUCTOR-SMD 1.5uH,10%,2x1.25x0.85mm
C100 2203-000260 C-CERAMIC,CHIP 10NF,10%,50V,X7R,TP,2012
C101 2402-000168 C-AL,SMD 100uF,20%,16V,GP,TP,8.3x8.3x6.3mm
C102 2203-000260 C-CERAMIC,CHIP 10NF,10%,50V,X7R,TP,2012
C103 2402-000168 C-AL,SMD 100uF,20%,16V,GP,TP,8.3x8.3x6.3mm
C104 2203-000260 C-CERAMIC,CHIP 10NF,10%,50V,X7R,TP,2012
C105 2402-000168 C-AL,SMD 100uF,20%,16V,GP,TP,8.3x8.3x6.3mm
C106 2402-000168 C-AL,SMD 100uF,20%,16V,GP,TP,8.3x8.3x6.3mm
C107 2203-000239 C-CERAMIC,CHIP 0.1nF,5%,50V,NPO,TP,2012
C108 2203-000239 C-CERAMIC,CHIP 0.1nF,5%,50V,NPO,TP,2012
C109 2203-000260 C-CERAMIC,CHIP 10NF,10%,50V,X7R,TP,2012
C110 2203-000204 C-CERAMIC,CHIP 100NF,10%,25V,X7R,TP,2012
C111 2203-000204 C-CERAMIC,CHIP 100NF,10%,25V,X7R,TP,2012
C112 2203-000204 C-CERAMIC,CHIP 100NF,10%,25V,X7R,TP,2012
C113 2203-000204 C-CERAMIC,CHIP 100NF,10%,25V,X7R,TP,2012
C114 2203-000204 C-CERAMIC,CHIP 100NF,10%,25V,X7R,TP,2012
C115 2404-000123 C-TA,CHIP 10uF,20%,16V,TP,6032,2.9mm
C116 2203-000260 C-CERAMIC,CHIP 10NF,10%,50V,X7R,TP,2012
C117 2203-000204 C-CERAMIC,CHIP 100NF,10%,25V,X7R,TP,2012
C118 2203-000260 C-CERAMIC,CHIP 10NF,10%,50V,X7R,TP,2012
C119 2203-000204 C-CERAMIC,CHIP 100NF,10%,25V,X7R,TP,2012
C120 2203-000260 C-CERAMIC,CHIP 10NF,10%,50V,X7R,TP,2012
C121 2203-000204 C-CERAMIC,CHIP 100NF,10%,25V,X7R,TP,2012
C122 2203-000260 C-CERAMIC,CHIP 10NF,10%,50V,X7R,TP,2012
C123 2203-000609 C-CERAMIC,CHIP 22NF,10%,50V,X7R,TP,2012
C124 2203-000260 C-CERAMIC,CHIP 10NF,10%,50V,X7R,TP,2012
C125 2203-000609 C-CERAMIC,CHIP 22NF,10%,50V,X7R,TP,2012
C126 2203-000260 C-CERAMIC,CHIP 10NF,10%,50V,X7R,TP,2012
C127 2203-000609 C-CERAMIC,CHIP 22NF,10%,50V,X7R,TP,2012
C128 2203-000151 C-CERAMIC,CHIP 1.5nF,5%,50V,NPO,TP,2012
C129 2203-000260 C-CERAMIC,CHIP 10NF,10%,50V,X7R,TP,2012
C130 2203-000260 C-CERAMIC,CHIP 10NF,10%,50V,X7R,TP,2012
C131 2203-000260 C-CERAMIC,CHIP 10NF,10%,50V,X7R,TP,2012
C132 2203-000260 C-CERAMIC,CHIP 10NF,10%,50V,X7R,TP,2012
C133 2203-000260 C-CERAMIC,CHIP 10NF,10%,50V,X7R,TP,2012
C134 2203-000260 C-CERAMIC,CHIP 10NF,10%,50V,X7R,TP,2012
C135 2203-000260 C-CERAMIC,CHIP 10NF,10%,50V,X7R,TP,2012

SyncMaster 570BTFT/580BTFT 6-1

Loc. No. Code No. Description Specification Remarks

6 Electrical Parts List

6-1 Main PCB Parts

C136 2203-000260 C-CERAMIC,CHIP 10NF,10%,50V,X7R,TP,2012
C137 2203-000204 C-CERAMIC,CHIP 100NF,10%,25V,X7R,TP,2012
C138 2203-000260 C-CERAMIC,CHIP 10NF,10%,50V,X7R,TP,2012
C139 2203-000204 C-CERAMIC,CHIP 100NF,10%,25V,X7R,TP,2012
C140 2203-000260 C-CERAMIC,CHIP 10NF,10%,50V,X7R,TP,2012
C141 2203-000204 C-CERAMIC,CHIP 100NF,10%,25V,X7R,TP,2012
C142 2203-001391 C-CERAMIC,CHIP 150nF,10%,25V,X7R,TP,2012
C143 2203-000455 C-CERAMIC,CHIP 1nF,5%,50V,NPO,TP,2012
C144 2203-000204 C-CERAMIC,CHIP 100NF,10%,25V,X7R,TP,2012
C145 2203-000260 C-CERAMIC,CHIP 10NF,10%,50V,X7R,TP,2012
C146 2203-000260 C-CERAMIC,CHIP 10NF,10%,50V,X7R,TP,2012
C147 2203-000204 C-CERAMIC,CHIP 100NF,10%,25V,X7R,TP,2012
C148 2203-000260 C-CERAMIC,CHIP 10NF,10%,50V,X7R,TP,2012
C149 2203-000204 C-CERAMIC,CHIP 100NF,10%,25V,X7R,TP,2012
C150 2203-000260 C-CERAMIC,CHIP 10NF,10%,50V,X7R,TP,2012
C151 2203-000204 C-CERAMIC,CHIP 100NF,10%,25V,X7R,TP,2012
C157 2203-000204 C-CERAMIC,CHIP 100NF,10%,25V,X7R,TP,2012
C158 2203-000204 C-CERAMIC,CHIP 100NF,10%,25V,X7R,TP,2012
C159 2402-000168 C-AL,SMD 100uF,20%,16V,GP,TP,8.3x8.3x6.3mm
C160 2203-000204 C-CERAMIC,CHIP 100NF,10%,25V,X7R,TP,2012
C161 2203-000204 C-CERAMIC,CHIP 100NF,10%,25V,X7R,TP,2012
C163 2203-000260 C-CERAMIC,CHIP 10NF,10%,50V,X7R,TP,2012
C165 2409-000124 C-ORGANIC 100uF,10%,16V,LZ,BK,8x10.5,3.5
C167 2402-000168 C-AL,SMD 100uF,20%,16V,GP,TP,8.3x8.3x6.3mm
C168 2203-000260 C-CERAMIC,CHIP 10NF,10%,50V,X7R,TP,2012
C169 2402-000168 C-AL,SMD 100uF,20%,16V,GP,TP,8.3x8.3x6.3mm
C172 2402-000168 C-AL,SMD 100uF,20%,16V,GP,TP,8.3x8.3x6.3mm
C173 2409-000124 C-ORGANIC 100uF,10%,16V,LZ,BK,8x10.5,3.5
C175 2404-000123 C-TA,CHIP 10uF,20%,16V,TP,6032,2.9mm
C176 2402-000168 C-AL,SMD 100uF,20%,16V,GP,TP,8.3x8.3x6.3mm
C177 2409-000124 C-ORGANIC 100uF,10%,16V,LZ,BK,8x10.5,3.5
C180 2404-000123 C-TA,CHIP 10uF,20%,16V,TP,6032,2.9mm
C181 2404-000123 C-TA,CHIP 10uF,20%,16V,TP,6032,2.9mm
C182 2203-000260 C-CERAMIC,CHIP 10NF,10%,50V,X7R,TP,2012
C183 2203-000204 C-CERAMIC,CHIP 100NF,10%,25V,X7R,TP,2012
C184 2203-000260 C-CERAMIC,CHIP 10NF,10%,50V,X7R,TP,2012
C185 2203-000204 C-CERAMIC,CHIP 100NF,10%,25V,X7R,TP,2012
C186 2404-000123 C-TA,CHIP 10uF,20%,16V,TP,6032,2.9mm
C187 2404-000123 C-TA,CHIP 10uF,20%,16V,TP,6032,2.9mm
C188 2203-000204 C-CERAMIC,CHIP 100NF,10%,25V,X7R,TP,2012
C189 2203-000260 C-CERAMIC,CHIP 10NF,10%,50V,X7R,TP,2012
C190 2203-000204 C-CERAMIC,CHIP 100NF,10%,25V,X7R,TP,2012
C192 2203-000151 C-CERAMIC,CHIP 1.5nF,5%,50V,NPO,TP,2012
C193 2404-000123 C-TA,CHIP 10uF,20%,16V,TP,6032,2.9mm
C194 2203-000260 C-CERAMIC,CHIP 10NF,10%,50V,X7R,TP,2012
C195 2203-000260 C-CERAMIC,CHIP 10NF,10%,50V,X7R,TP,2012
C196 2203-000260 C-CERAMIC,CHIP 10NF,10%,50V,X7R,TP,2012

6 Electrical Parts List

6-2 SyncMaster 570BTFT/580BTFT

Loc. No. Code No. Description Specification Remarks

C197 2203-000683 C-CERAMIC,CHIP 27pF,5%,50V,NPO,TP,2012
C198 2203-000683 C-CERAMIC,CHIP 27pF,5%,50V,NPO,TP,2012
C199 2203-000683 C-CERAMIC,CHIP 27pF,5%,50V,NPO,TP,2012
C301 2203-000204 C-CERAMIC,CHIP 100NF,10%,25V,X7R,TP,2012
C302 2203-000204 C-CERAMIC,CHIP 100NF,10%,25V,X7R,TP,2012
C303 2203-000204 C-CERAMIC,CHIP 100NF,10%,25V,X7R,TP,2012
C304 2203-000204 C-CERAMIC,CHIP 100NF,10%,25V,X7R,TP,2012
C305 2203-000204 C-CERAMIC,CHIP 100NF,10%,25V,X7R,TP,2012
C306 2203-000204 C-CERAMIC,CHIP 100NF,10%,25V,X7R,TP,2012
C307 2203-000204 C-CERAMIC,CHIP 100NF,10%,25V,X7R,TP,2012
C308 2203-000204 C-CERAMIC,CHIP 100NF,10%,25V,X7R,TP,2012
C309 2203-000204 C-CERAMIC,CHIP 100NF,10%,25V,X7R,TP,2012
C310 2203-000204 C-CERAMIC,CHIP 100NF,10%,25V,X7R,TP,2012
C311 2203-000204 C-CERAMIC,CHIP 100NF,10%,25V,X7R,TP,2012
C312 2203-000204 C-CERAMIC,CHIP 100NF,10%,25V,X7R,TP,2012
C313 2203-000204 C-CERAMIC,CHIP 100NF,10%,25V,X7R,TP,2012
C314 2203-000204 C-CERAMIC,CHIP 100NF,10%,25V,X7R,TP,2012
C315 2203-000204 C-CERAMIC,CHIP 100NF,10%,25V,X7R,TP,2012
C316 2203-000204 C-CERAMIC,CHIP 100NF,10%,25V,X7R,TP,2012
C317 2203-000204 C-CERAMIC,CHIP 100NF,10%,25V,X7R,TP,2012
C318 2203-000204 C-CERAMIC,CHIP 100NF,10%,25V,X7R,TP,2012
C319 2203-000204 C-CERAMIC,CHIP 100NF,10%,25V,X7R,TP,2012
C320 2203-000204 C-CERAMIC,CHIP 100NF,10%,25V,X7R,TP,2012
C321 2203-000204 C-CERAMIC,CHIP 100NF,10%,25V,X7R,TP,2012
C322 2203-000204 C-CERAMIC,CHIP 100NF,10%,25V,X7R,TP,2012
C323 2203-001723 C-CERAMIC,CHIP 4.7pF,5%,50V,NPO,TP,2012
C324 2203-000204 C-CERAMIC,CHIP 100NF,10%,25V,X7R,TP,2012
C325 2203-000204 C-CERAMIC,CHIP 100NF,10%,25V,X7R,TP,2012
C326 2203-000204 C-CERAMIC,CHIP 100NF,10%,25V,X7R,TP,2012
C327 2203-000204 C-CERAMIC,CHIP 100NF,10%,25V,X7R,TP,2012
C328 2203-000204 C-CERAMIC,CHIP 100NF,10%,25V,X7R,TP,2012
C329 2203-000204 C-CERAMIC,CHIP 100NF,10%,25V,X7R,TP,2012
C330 2203-000204 C-CERAMIC,CHIP 100NF,10%,25V,X7R,TP,2012
C331 2203-000204 C-CERAMIC,CHIP 100NF,10%,25V,X7R,TP,2012
C332 2203-000204 C-CERAMIC,CHIP 100NF,10%,25V,X7R,TP,2012
C333 2203-000204 C-CERAMIC,CHIP 100NF,10%,25V,X7R,TP,2012
C334 2203-000204 C-CERAMIC,CHIP 100NF,10%,25V,X7R,TP,2012
C335 2203-000204 C-CERAMIC,CHIP 100NF,10%,25V,X7R,TP,2012
C336 2203-000204 C-CERAMIC,CHIP 100NF,10%,25V,X7R,TP,2012
C337 2203-000204 C-CERAMIC,CHIP 100NF,10%,25V,X7R,TP,2012
C338 2203-000204 C-CERAMIC,CHIP 100NF,10%,25V,X7R,TP,2012
C339 2203-000204 C-CERAMIC,CHIP 100NF,10%,25V,X7R,TP,2012
C340 2203-000204 C-CERAMIC,CHIP 100NF,10%,25V,X7R,TP,2012
C341 2203-000204 C-CERAMIC,CHIP 100NF,10%,25V,X7R,TP,2012
C342 2203-000204 C-CERAMIC,CHIP 100NF,10%,25V,X7R,TP,2012
C343 2203-000204 C-CERAMIC,CHIP 100NF,10%,25V,X7R,TP,2012
C344 2203-000204 C-CERAMIC,CHIP 100NF,10%,25V,X7R,TP,2012

6 Electrical Parts List

SyncMaster 570BTFT/580BTFT 6-3

Loc. No. Code No. Description Specification Remarks

C345 2203-000204 C-CERAMIC,CHIP 100NF,10%,25V,X7R,TP,2012
C346 2203-000204 C-CERAMIC,CHIP 100NF,10%,25V,X7R,TP,2012
C347 2203-000204 C-CERAMIC,CHIP 100NF,10%,25V,X7R,TP,2012
C348 2203-000204 C-CERAMIC,CHIP 100NF,10%,25V,X7R,TP,2012
C349 2203-000204 C-CERAMIC,CHIP 100NF,10%,25V,X7R,TP,2012
C350 2203-000204 C-CERAMIC,CHIP 100NF,10%,25V,X7R,TP,2012
C351 2203-000204 C-CERAMIC,CHIP 100NF,10%,25V,X7R,TP,2012
C352 2203-000204 C-CERAMIC,CHIP 100NF,10%,25V,X7R,TP,2012
C353 2203-000204 C-CERAMIC,CHIP 100NF,10%,25V,X7R,TP,2012
C354 2203-000204 C-CERAMIC,CHIP 100NF,10%,25V,X7R,TP,2012
C355 2203-000204 C-CERAMIC,CHIP 100NF,10%,25V,X7R,TP,2012
C356 2203-000204 C-CERAMIC,CHIP 100NF,10%,25V,X7R,TP,2012
C357 2203-000204 C-CERAMIC,CHIP 100NF,10%,25V,X7R,TP,2012
C358 2203-000204 C-CERAMIC,CHIP 100NF,10%,25V,X7R,TP,2012
C359 2203-000204 C-CERAMIC,CHIP 100NF,10%,25V,X7R,TP,2012
C360 2203-000204 C-CERAMIC,CHIP 100NF,10%,25V,X7R,TP,2012
C361 2203-000204 C-CERAMIC,CHIP 100NF,10%,25V,X7R,TP,2012
C363 2203-000260 C-CERAMIC,CHIP 10NF,10%,50V,X7R,TP,2012
C364 2404-000123 C-TA,CHIP 10uF,20%,16V,TP,6032,2.9mm
C365 2203-000204 C-CERAMIC,CHIP 100NF,10%,25V,X7R,TP,2012
C367 2203-000818 C-CERAMIC,CHIP 0.033nF,5%,50V,NPO,TP,2012
C368 2203-000818 C-CERAMIC,CHIP 0.033nF,5%,50V,NPO,TP,2012
C369 2404-000151 C-TA,CHIP 1uF,20%,16V,TP,3216
C370 2404-000151 C-TA,CHIP 1uF,20%,16V,TP,3216
C371 2404-000123 C-TA,CHIP 10uF,20%,16V,TP,6032,2.9mm
C372 2203-000260 C-CERAMIC,CHIP 10NF,10%,50V,X7R,TP,2012
C389 2203-000204 C-CERAMIC,CHIP 100NF,10%,25V,X7R,TP,2012
C390 2203-000204 C-CERAMIC,CHIP 100NF,10%,25V,X7R,TP,2012
C401 2203-000260 C-CERAMIC,CHIP 10NF,10%,50V,X7R,TP,2012
C402 2404-000123 C-TA,CHIP 10uF,20%,16V,TP,6032,2.9mm
C403 2203-000260 C-CERAMIC,CHIP 10NF,10%,50V,X7R,TP,2012
C404 2404-000123 C-TA,CHIP 10uF,20%,16V,TP,6032,2.9mm
C405 2203-000455 C-CERAMIC,CHIP 1nF,5%,50V,NPO,TP,2012
C407 2203-000204 C-CERAMIC,CHIP 100NF,10%,25V,X7R,TP,2012
C408 2402-000168 C-AL,SMD 100uF,20%,16V,GP,TP,8.3x8.3x6.3mm
C409 2404-000123 C-TA,CHIP 10uF,20%,16V,TP,6032,2.9mm
C410 2203-000260 C-CERAMIC,CHIP 10NF,10%,50V,X7R,TP,2012
C411 2203-000204 C-CERAMIC,CHIP 100NF,10%,25V,X7R,TP,2012
C412 2404-000123 C-TA,CHIP 10uF,20%,16V,TP,6032,2.9mm
C413 2203-000555 C-CERAMIC,CHIP 20pF,5%,50V,NPO,TP,2012
C414 2203-000555 C-CERAMIC,CHIP 20pF,5%,50V,NPO,TP,2012
C415 2404-000123 C-TA,CHIP 10uF,20%,16V,TP,6032,2.9mm
C416 2203-000260 C-CERAMIC,CHIP 10NF,10%,50V,X7R,TP,2012
C417 2203-000239 C-CERAMIC,CHIP 0.1nF,5%,50V,NPO,TP,2012
C473 2404-000123 C-TA,CHIP 10uF,20%,16V,TP,6032,2.9mm
C474 2203-000204 C-CERAMIC,CHIP 100NF,10%,25V,X7R,TP,2012
C496 2203-000260 C-CERAMIC,CHIP 10NF,10%,50V,X7R,TP,2012

6 Electrical Parts List

6-4 SyncMaster 570BTFT/580BTFT

Loc. No. Code No. Description Specification Remarks

C497 2203-000260 C-CERAMIC,CHIP 10NF,10%,50V,X7R,TP,2012
C498 2203-000260 C-CERAMIC,CHIP 10NF,10%,50V,X7R,TP,2012
C499 2203-000260 C-CERAMIC,CHIP 10NF,10%,50V,X7R,TP,2012
C501 2404-000123 C-TA,CHIP 10uF,20%,16V,TP,6032,2.9mm
C502 2203-000455 C-CERAMIC,CHIP 1nF,5%,50V,NPO,TP,2012
C509 2404-000123 C-TA,CHIP 10uF,20%,16V,TP,6032,2.9mm
C510 2203-000455 C-CERAMIC,CHIP 1nF,5%,50V,NPO,TP,2012
C511 2404-000123 C-TA,CHIP 10uF,20%,16V,TP,6032,2.9mm
C512 2203-000455 C-CERAMIC,CHIP 1nF,5%,50V,NPO,TP,2012
CFT301 2901-001115 FILTER-EMI SMD 50VDC,500mADC,20pF,3.1x1.6x2
CFT317 2901-001112 FILTER-EMI SMD 50VDC,1.0ADC,85pF+-20%,3.2x1
CFT318 2901-001115 FILTER-EMI SMD 50VDC,500mADC,20pF,3.1x1.6x2
CL101 BN27-20001C COIL-SMD
CL102 BN27-20001A COIL-CHOKE
CN101 3701-001129 CONNECTOR-DSUB 15P,3R,FEMALE,ANGLE,AUF
CN102 3722-000117 JACK-DC POWER 3P,3.5mm,AG,BLK,NO
CN103 3711-000556 CONNECTOR-HEADER BOX,12P,1R,1.25mm,SMD-A,SN
CN301 3711-003161 CONNECTOR-HEADER BOX,20P,1R,1.25mm,ANGLE,SN
CN401 3711-002049 CONNECTOR-HEADER BOX,6P,1R,1.25mm,SMD-A,SN
CN402 3711-000056 CONNECTOR-HEADER BOX,2P,1R,2.5mm,ANGLE,SN
D101 0401-001056 DIODE-SWITCHING MMBD4148SE,75V,600mA,SOT-23,TP
D102 0401-001056 DIODE-SWITCHING MMBD4148SE,75V,600mA,SOT-23,TP
D103 0401-001056 DIODE-SWITCHING MMBD4148SE,75V,600mA,SOT-23,TP
D109 0401-001056 DIODE-SWITCHING MMBD4148SE,75V,600mA,SOT-23,TP
D113 0402-000553 DIODE-RECTIFIER SS24,40V,2.0A,DO-214AA
D114 0402-000553 DIODE-RECTIFIER SS24,40V,2.0A,DO-214AA
D402 0401-001056 DIODE-SWITCHING MMBD4148SE,75V,600mA,SOT-23,TP
D404 0401-001056 DIODE-SWITCHING MMBD4148SE,75V,600mA,SOT-23,TP
FT100 3301-001145 CORE-FERRITE BEAD AB,4.5x1.6x1.6mm,­FT101 2901-001114 FILTER-EMI SMD 25VDC,2.0ADC,100nF,3.2x1.6x1
FT102 2901-001114 FILTER-EMI SMD 25VDC,2.0ADC,100nF,3.2x1.6x1
FT103 2901-001114 FILTER-EMI SMD 25VDC,2.0ADC,100nF,3.2x1.6x1
FT120 2901-001114 FILTER-EMI SMD 25VDC,2.0ADC,100nF,3.2x1.6x1
FT122 2901-000172 FILTER-EMI ON BOARD 50V,10A,-,12x11x13mm,BK
FT301 2901-001114 FILTER-EMI SMD 25VDC,2.0ADC,100nF,3.2x1.6x1
FT306 2901-001114 FILTER-EMI SMD 25VDC,2.0ADC,100nF,3.2x1.6x1
FT313 2901-001114 FILTER-EMI SMD 25VDC,2.0ADC,100nF,3.2x1.6x1
FT314 2901-001114 FILTER-EMI SMD 25VDC,2.0ADC,100nF,3.2x1.6x1
FT316 2901-001114 FILTER-EMI SMD 25VDC,2.0ADC,100nF,3.2x1.6x1
FT317 2901-001114 FILTER-EMI SMD 25VDC,2.0ADC,100nF,3.2x1.6x1
FT318 2901-001114 FILTER-EMI SMD 25VDC,2.0ADC,100nF,3.2x1.6x1
FT319 2901-001114 FILTER-EMI SMD 25VDC,2.0ADC,100nF,3.2x1.6x1
FT321 2901-001113 FILTER-EMI SMD 25VDC,0.2A,35pF+-20%,2x1.25x
FT322 2901-001113 FILTER-EMI SMD 25VDC,0.2A,35pF+-20%,2x1.25x
FT323 2901-001113 FILTER-EMI SMD 25VDC,0.2A,35pF+-20%,2x1.25x
FT324 2901-001113 FILTER-EMI SMD 25VDC,0.2A,35pF+-20%,2x1.25x
FT325 2901-001113 FILTER-EMI SMD 25VDC,0.2A,35pF+-20%,2x1.25x

6 Electrical Parts List

SyncMaster 570BTFT/580BTFT 6-5

Loc. No. Code No. Description Specification Remarks

FT326 2901-001113 FILTER-EMI SMD 25VDC,0.2A,35pF+-20%,2x1.25x
FT327 2901-001113 FILTER-EMI SMD 25VDC,0.2A,35pF+-20%,2x1.25x
FT328 2901-001113 FILTER-EMI SMD 25VDC,0.2A,35pF+-20%,2x1.25x
FT329 2901-001113 FILTER-EMI SMD 25VDC,0.2A,35pF+-20%,2x1.25x
FT330 2901-001113 FILTER-EMI SMD 25VDC,0.2A,35pF+-20%,2x1.25x
FT336 2901-001114 FILTER-EMI SMD 25VDC,2.0ADC,100nF,3.2x1.6x1
FT415 2901-001114 FILTER-EMI SMD 25VDC,2.0ADC,100nF,3.2x1.6x1
FT521 2901-001114 FILTER-EMI SMD 25VDC,2.0ADC,100nF,3.2x1.6x1
FT529 2901-001114 FILTER-EMI SMD 25VDC,2.0ADC,100nF,3.2x1.6x1
FT531 2901-001114 FILTER-EMI SMD 25VDC,2.0ADC,100nF,3.2x1.6x1
IC101 1002-001099 IC-A/D CONVERTER TDA8752,8BIT,QFP,100P,+-0.5,
IC102 1203-001488 IC-POSI.FIXED REG. 7805,T0-252,3P,PLASTIC,4.8/5
IC103 1203-001488 IC-POSI.FIXED REG. 7805,T0-252,3P,PLASTIC,4.8/5
IC104 1204-000292 IC-VIDEO SYSTEM LM1881M,SOP,8P,150MIL,PLASTIC,
IC105 0803-000117 IC-TTL 74F14,INVERTER,SOP,14P,150MIL,
IC106 0803-000122 IC-TTL 74F125,BUFFER,SOP,14P,150MIL,Q
IC107 1203-001448 IC-POSI.FIXED REG. 2596,TO-263,5P,PLASTIC,4.750
IC108 1203-001447 IC-POSI.FIXED REG. 2596,TO-263,5P,PLASTIC,3.135
IC109 1203-001488 IC-POSI.FIXED REG. 7805,T0-252,3P,PLASTIC,4.8/5
IC111 0505-000275 FET-SILICON SI4435DY,P,-30V,+-8.0A,0.02ohm
IC115 1203-001538 IC-POSI.ADJUST REG. 431,SOT-89,3P,PLASTIC,2.47/3
IC151 0803-000275 IC-TTL 74F32,OR GATE,SOP,14P,150MIL,Q
IC192 BN13-00002A IC-ASIC XB(LCD),FG60A018HM_L18,QFP,48P,AUTO
IC301 1205-001407 IC-BUFFER GMFC1,QFP,208P,PLASTIC,3.6V,
IC302 1105-001165 IC-DRAM 416S1020,512Kx16BITx2,TSOP,50P
IC303 1105-001165 IC-DRAM 416S1020,512Kx16BITx2,TSOP,50P
IC304 1105-001165 IC-DRAM 416S1020,512Kx16BITx2,TSOP,50P
IC305 0904-001222 IC-GRAPHIC CONT. GMZ1,QFP,208P,65MHz,TR,P
IC307 BN09-00001A IC-OSD PROCESSOR LCD,MTV121P-31,16P
IC309 0505-001170 FET-SILICON SI9933ADY-T1,P,-20V,3.4A,0.075OHM,2W,SO-8
IC401 0903-001063 IC-MICROCONTROLLER 72E75,8BIT,DIP,42P,600MIL,24MH
IC401_SOCK 3704-001071 SOCKET-IC 42P,DIP,SN,1.778mm
IC402 1203-001109 IC-VOL. DETECTOR 7045,SOT-89,3P,PLASTIC,4.3/4
IC403 1103-001164 IC-EEPROM 24LC21A,128X8BIT,SOP,8P,150MIL,5V,10%,

PLASTIC,0 TO +70C,100UA,CMOS,TP
IC404 1103-001023 IC-EEPROM 24C08,1028x8BIT,SOP,8P,150MIL,
IC406 0803-000122 IC-TTL 74F125,BUFFER,SOP,14P,150MIL,Q
IC501 1205-001740 IC-TRANSMITTER DS90C385,TSSOP,56P,240MIL,PLASTIC,4V,

1.63W,10 TO +70C,ST,FPD LINK-85MHZ(LVDS)
L102 2703-001070 INDUCTOR-SMD 100uH,10%,4.5x3.2x3.2mm
L151 2703-001070 INDUCTOR-SMD 100uH,10%,4.5x3.2x3.2mm
L152 2703-001070 INDUCTOR-SMD 100uH,10%,4.5x3.2x3.2mm
L160 2703-001070 INDUCTOR-SMD 100uH,10%,4.5x3.2x3.2mm
L170 2703-001070 INDUCTOR-SMD 100uH,10%,4.5x3.2x3.2mm
L171 2703-001070 INDUCTOR-SMD 100uH,10%,4.5x3.2x3.2mm
L172 2703-001070 INDUCTOR-SMD 100uH,10%,4.5x3.2x3.2mm
L193 2703-001070 INDUCTOR-SMD 100uH,10%,4.5x3.2x3.2mm

6 Electrical Parts List

6-6 SyncMaster 570BTFT/580BTFT

Loc. No. Code No. Description Specification Remarks

L403 2703-001070 INDUCTOR-SMD 100uH,10%,4.5x3.2x3.2mm
L406 2703-001070 INDUCTOR-SMD 100uH,10%,4.5x3.2x3.2mm
L407 2703-001070 INDUCTOR-SMD 100uH,10%,4.5x3.2x3.2mm
Q101 0501-002080 TR-SMALL SIGNAL 2SC2412K,NPN,200mW,SOT-23,TP,1
Q102 0501-002080 TR-SMALL SIGNAL 2SC2412K,NPN,200mW,SOT-23,TP,1
Q301 0501-002080 TR-SMALL SIGNAL 2SC2412K,NPN,200mW,SOT-23,TP,1
Q302 0501-002080 TR-SMALL SIGNAL 2SC2412K,NPN,200mW,SOT-23,TP,1
Q401 0501-002080 TR-SMALL SIGNAL 2SC2412K,NPN,200mW,SOT-23,TP,1
Q402 0501-002080 TR-SMALL SIGNAL 2SC2412K,NPN,200mW,SOT-23,TP,1
R101 2007-001166 R-CHIP 75OHM,5%,1/10W,DA,TP,2012
R102 2007-001166 R-CHIP 75OHM,5%,1/10W,DA,TP,2012
R103 2007-001166 R-CHIP 75OHM,5%,1/10W,DA,TP,2012
R104 2007-000781 R-CHIP 33OHM,5%,1/10W,DA,TP,2012
R105 2007-000781 R-CHIP 33OHM,5%,1/10W,DA,TP,2012
R106 2007-000781 R-CHIP 33OHM,5%,1/10W,DA,TP,2012
R107 2007-000493 R-CHIP 2.2KOHM,5%,1/10W,DA,TP,2012
R110 2007-000290 R-CHIP 100OHM,5%,1/10W,DA,TP,2012
R115 2007-000593 R-CHIP 22OHM,5%,1/10W,DA,TP,2012
R116 2007-000593 R-CHIP 22OHM,5%,1/10W,DA,TP,2012
R117 2007-000023 R-CHIP 120OHM,5%,1/10W,DA,TP,2012
R124 2007-000593 R-CHIP 22OHM,5%,1/10W,DA,TP,2012
R125 2007-000593 R-CHIP 22OHM,5%,1/10W,DA,TP,2012
R127 2007-000300 R-CHIP 10KOHM,5%,1/10W,DA,TP,2012
R129 2007-000822 R-CHIP 390OHM,5%,1/10W,DA,TP,2012
R130 2007-000290 R-CHIP 100OHM,5%,1/10W,DA,TP,2012
R131 2007-000290 R-CHIP 100OHM,5%,1/10W,DA,TP,2012
R134 2007-000468 R-CHIP 1KOHM,5%,1/10W,DA,TP,2012
R136 2007-000872 R-CHIP 4.7KOHM,5%,1/10W,DA,TP,2012
R137 2007-000872 R-CHIP 4.7KOHM,5%,1/10W,DA,TP,2012
R138 2007-000872 R-CHIP 4.7KOHM,5%,1/10W,DA,TP,2012
R139 2007-000221 R-CHIP 1.2KOHM,5%,1/10W,DA,TP,2012
R142 2007-000872 R-CHIP 4.7KOHM,5%,1/10W,DA,TP,2012
R143 2007-000221 R-CHIP 1.2KOHM,5%,1/10W,DA,TP,2012
R190 2007-000029 R-CHIP 0OHM,5%,1/10W,DA,TP,2012
R191 2007-000029 R-CHIP 0OHM,5%,1/10W,DA,TP,2012
R192 2007-001113 R-CHIP 680KOHM,5%,1/10W,DA,TP,2012
R193 2007-000593 R-CHIP 22OHM,5%,1/10W,DA,TP,2012
R194 2007-000872 R-CHIP 4.7KOHM,5%,1/10W,DA,TP,2012
R195 2007-000572 R-CHIP 220OHM,5%,1/10W,DA,TP,2012
R196 2007-000468 R-CHIP 1KOHM,5%,1/10W,DA,TP,2012
R197 2007-000029 R-CHIP 0OHM,5%,1/10W,DA,TP,2012
R198 2007-000029 R-CHIP 0OHM,5%,1/10W,DA,TP,2012
R199 2007-000029 R-CHIP 0OHM,5%,1/10W,DA,TP,2012
R301 2007-000468 R-CHIP 1KOHM,5%,1/10W,DA,TP,2012
R302 2007-000468 R-CHIP 1KOHM,5%,1/10W,DA,TP,2012
R303 2007-000290 R-CHIP 100OHM,5%,1/10W,DA,TP,2012
R305 2007-000468 R-CHIP 1KOHM,5%,1/10W,DA,TP,2012

6 Electrical Parts List

SyncMaster 570BTFT/580BTFT 6-7

Loc. No. Code No. Description Specification Remarks

R306 2007-000290 R-CHIP 100OHM,5%,1/10W,DA,TP,2012
R307 2007-000290 R-CHIP 100OHM,5%,1/10W,DA,TP,2012
R308 2007-000282 R-CHIP 100KOHM,5%,1/10W,DA,TP,2012
R310 2007-000300 R-CHIP 10KOHM,5%,1/10W,DA,TP,2012
R311 2007-000282 R-CHIP 100KOHM,5%,1/10W,DA,TP,2012
R312 2007-000300 R-CHIP 10KOHM,5%,1/10W,DA,TP,2012
R314 2007-000593 R-CHIP 22OHM,5%,1/10W,DA,TP,2012
R316 2007-000766 R-CHIP 330OHM,5%,1/10W,DA,TP,2012
R317 2007-000572 R-CHIP 220OHM,5%,1/10W,DA,TP,2012
R321 2007-000468 R-CHIP 1KOHM,5%,1/10W,DA,TP,2012
R401 2007-000941 R-CHIP 47KOHM,5%,1/10W,DA,TP,2012
R402 2007-000941 R-CHIP 47KOHM,5%,1/10W,DA,TP,2012
R403 2007-000941 R-CHIP 47KOHM,5%,1/10W,DA,TP,2012
R404 2007-000941 R-CHIP 47KOHM,5%,1/10W,DA,TP,2012
R405 2007-000941 R-CHIP 47KOHM,5%,1/10W,DA,TP,2012
R406 2007-000872 R-CHIP 4.7KOHM,5%,1/10W,DA,TP,2012
R407 2007-000941 R-CHIP 47KOHM,5%,1/10W,DA,TP,2012
R408 2007-000941 R-CHIP 47KOHM,5%,1/10W,DA,TP,2012
R409 2007-000941 R-CHIP 47KOHM,5%,1/10W,DA,TP,2012
R410 2007-000872 R-CHIP 4.7KOHM,5%,1/10W,DA,TP,2012
R412 2007-000872 R-CHIP 4.7KOHM,5%,1/10W,DA,TP,2012
R413 2007-000872 R-CHIP 4.7KOHM,5%,1/10W,DA,TP,2012
R414 2007-000941 R-CHIP 47KOHM,5%,1/10W,DA,TP,2012
R415 2007-000941 R-CHIP 47KOHM,5%,1/10W,DA,TP,2012
R416 2007-000941 R-CHIP 47KOHM,5%,1/10W,DA,TP,2012
R417 2007-000290 R-CHIP 100OHM,5%,1/10W,DA,TP,2012
R418 2007-000290 R-CHIP 100OHM,5%,1/10W,DA,TP,2012
R419 2007-000290 R-CHIP 100OHM,5%,1/10W,DA,TP,2012
R420 2007-000290 R-CHIP 100OHM,5%,1/10W,DA,TP,2012
R421 2007-000290 R-CHIP 100OHM,5%,1/10W,DA,TP,2012
R422 2007-000290 R-CHIP 100OHM,5%,1/10W,DA,TP,2012
R423 2007-000290 R-CHIP 100OHM,5%,1/10W,DA,TP,2012
R424 2007-000290 R-CHIP 100OHM,5%,1/10W,DA,TP,2012
R425 2007-000290 R-CHIP 100OHM,5%,1/10W,DA,TP,2012
R426 2007-000290 R-CHIP 100OHM,5%,1/10W,DA,TP,2012
R427 2007-000290 R-CHIP 100OHM,5%,1/10W,DA,TP,2012
R429 2007-000290 R-CHIP 100OHM,5%,1/10W,DA,TP,2012
R431 2007-000290 R-CHIP 100OHM,5%,1/10W,DA,TP,2012
R432 2007-000290 R-CHIP 100OHM,5%,1/10W,DA,TP,2012
R433 2007-000290 R-CHIP 100OHM,5%,1/10W,DA,TP,2012
R436 2007-000290 R-CHIP 100OHM,5%,1/10W,DA,TP,2012
R437 2007-000290 R-CHIP 100OHM,5%,1/10W,DA,TP,2012
R438 2007-000290 R-CHIP 100OHM,5%,1/10W,DA,TP,2012
R439 2007-000290 R-CHIP 100OHM,5%,1/10W,DA,TP,2012
R440 2007-001166 R-CHIP 75OHM,5%,1/10W,DA,TP,2012
R441 2007-000290 R-CHIP 100OHM,5%,1/10W,DA,TP,2012
R442 2007-000290 R-CHIP 100OHM,5%,1/10W,DA,TP,2012

6 Electrical Parts List

6-8 SyncMaster 570BTFT/580BTFT

Loc. No. Code No. Description Specification Remarks

R443 2007-000290 R-CHIP 100OHM,5%,1/10W,DA,TP,2012
R444 2007-000290 R-CHIP 100OHM,5%,1/10W,DA,TP,2012
R445 2007-000290 R-CHIP 100OHM,5%,1/10W,DA,TP,2012
R447 2007-000290 R-CHIP 100OHM,5%,1/10W,DA,TP,2012
R448 2007-000290 R-CHIP 100OHM,5%,1/10W,DA,TP,2012
R449 2007-000468 R-CHIP 1KOHM,5%,1/10W,DA,TP,2012
R451 2007-000822 R-CHIP 390OHM,5%,1/10W,DA,TP,2012
R452 2007-000468 R-CHIP 1KOHM,5%,1/10W,DA,TP,2012
R453 2007-000941 R-CHIP 47KOHM,5%,1/10W,DA,TP,2012
R454 2007-000290 R-CHIP 100OHM,5%,1/10W,DA,TP,2012
R455 2007-000477 R-CHIP 1MOHM,5%,1/10W,DA,TP,2012
R456 2007-000572 R-CHIP 220OHM,5%,1/10W,DA,TP,2012
R457 2007-000290 R-CHIP 100OHM,5%,1/10W,DA,TP,2012
R458 2007-000290 R-CHIP 100OHM,5%,1/10W,DA,TP,2012
R459 2007-000409 R-CHIP 15KOHM,5%,1/10W,DA,TP,2012
R460 2007-000409 R-CHIP 15KOHM,5%,1/10W,DA,TP,2012
R461 2007-000290 R-CHIP 100OHM,5%,1/10W,DA,TP,2012
R462 2007-000290 R-CHIP 100OHM,5%,1/10W,DA,TP,2012
R463 2007-000290 R-CHIP 100OHM,5%,1/10W,DA,TP,2012
R464 2007-000468 R-CHIP 1KOHM,5%,1/10W,DA,TP,2012
R465 2007-000941 R-CHIP 47KOHM,5%,1/10W,DA,TP,2012
R466 2007-000023 R-CHIP 120OHM,5%,1/10W,DA,TP,2012
R467 2007-000931 R-CHIP 470OHM,5%,1/10W,DA,TP,2012
R470 2007-000941 R-CHIP 47KOHM,5%,1/10W,DA,TP,2012
RA101 2011-000002 R-NETWORK 22ohm,5%,1/16W,L,CHIP,8P,TP
RA102 2011-000002 R-NETWORK 22ohm,5%,1/16W,L,CHIP,8P,TP
RA103 2011-000002 R-NETWORK 22ohm,5%,1/16W,L,CHIP,8P,TP
RA104 2011-000002 R-NETWORK 22ohm,5%,1/16W,L,CHIP,8P,TP
RA105 2011-000002 R-NETWORK 22ohm,5%,1/16W,L,CHIP,8P,TP
RA106 2011-000002 R-NETWORK 22ohm,5%,1/16W,L,CHIP,8P,TP
RA107 2011-001015 R-NETWORK 1Kohm,5%,1/16W,L,CHIP,8P,TP
RA108 2011-001015 R-NETWORK 1Kohm,5%,1/16W,L,CHIP,8P,TP
RA109 2011-001015 R-NETWORK 1Kohm,5%,1/16W,L,CHIP,8P,TP
RA110 2011-001015 R-NETWORK 1Kohm,5%,1/16W,L,CHIP,8P,TP
RA111 2011-001015 R-NETWORK 1Kohm,5%,1/16W,L,CHIP,8P,TP
RA112 2011-001015 R-NETWORK 1Kohm,5%,1/16W,L,CHIP,8P,TP
RA301 2011-000002 R-NETWORK 22ohm,5%,1/16W,L,CHIP,8P,TP
RA302 2011-000002 R-NETWORK 22ohm,5%,1/16W,L,CHIP,8P,TP
RA303 2011-000002 R-NETWORK 22ohm,5%,1/16W,L,CHIP,8P,TP
RA304 2011-000002 R-NETWORK 22ohm,5%,1/16W,L,CHIP,8P,TP
RA305 2011-000002 R-NETWORK 22ohm,5%,1/16W,L,CHIP,8P,TP
SW301 BH39-40305U CBF HARNESS ,52MM,AWG22(0.6PI)
SW301_S 3710-000001 CONNECTOR-SHUNT 2P,1R,2.54mm,SN
X301 2804-001217 OSCILLATOR-CLOCK 67MHz,100ppm,10TTL & CMOS(30pF
X302 2804-001164 OSCILLATOR-CLOCK 85MHz,100ppm,10TTL(15pF),ST,3
X401 2801-003326 CRYSTAL-SMD 24MHz,30ppm,28-ABX,16pF,50ohm
ZD101 0403-000579 DIODE-ZENER BZX84C5V1,5.1V,5%,200mW,SOT-23

6 Electrical Parts List

SyncMaster 570BTFT/580BTFT 6-9

Loc. No. Code No. Description Specification Remarks

ZD102 0403-000579 DIODE-ZENER BZX84C5V1,5.1V,5%,200mW,SOT-23
ZD103 0403-000579 DIODE-ZENER BZX84C5V1,5.1V,5%,200mW,SOT-23
ZD104 0403-000579 DIODE-ZENER BZX84C5V1,5.1V,5%,200mW,SOT-23
ZD105 0403-000579 DIODE-ZENER BZX84C5V1,5.1V,5%,200mW,SOT-23
ZD401 0403-000579 DIODE-ZENER BZX84C5V1,5.1V,5%,200mW,SOT-23

6 Electrical Parts List

6-10 SyncMaster 570BTFT/580BTFT

Loc. No. Code No. Description Specification Remarks

CN801 3711-002050 slcon12p, CONNECTOR-HEADER BOX,10P,1R,1.25mm,SMD-A,SN
OP801 0601-001047 2_led, LED ROUND,GRN/YEL,2mm,585nm
R801 2007-000300 res, R-CHIP 10Kohm,5%,1/10W,DA,TP,2012
R802 2007-000301 res, R-CHIP 10Kohm,5%,1/10W,DA,TP,2013
R803 2007-000302 res, R-CHIP 10Kohm,5%,1/10W,DA,TP,2014
SW801 3404-000243 sw_tact2p, SWITCH-TACT 15V,20mA,160gf+-50gf,6x3.5mm,S
SW802 3404-000244 sw_tact2p, SWITCH-TACT 15V,20mA,160gf+-50gf,6x3.6mm,S
SW803 3404-000245 sw_tact2p, SWITCH-TACT 15V,20mA,160gf+-50gf,6x3.7mm,S
SW804 3404-000246 sw_tact3p, SWITCH-TACT 15V,20mA,160gf+-50gf,6x3.8mm,S
SW805 3404-000247 sw_tact4p, SWITCH-TACT 15V,20mA,160gf+-50gf,6x3.9mm,S
SW806 3404-000248 sw_tact5p, SWITCH-TACT 15V,20mA,160gf+-50gf,6x3.10mm,S

6 Electrical Parts List

SyncMaster 570BTFT/580BTFT 6-11

Loc. No. Code No. Description Specification Remarks

7-2 Sub PCB Parts

LCD BN07-00005A LCD-PANNEL LTM150XS-L02,331.3*257.9*15.9,TN VERTICAL STRIPE,0.297*0.297
P/CORD BH39-10307X CBF-POWER/CORD DET,H05VV-F,250V/6A,IVY,1830MM
S/CABLE BN39-00030A CBF-SIGNAL DETACHABLE,1830MM,15P/15P,2990,D-SUB-MALE
PROCESS-PBA UNIT BN94-00014C ASSY,PCB-ST RN15MS-XGD1/0000,EDC,EUROPE
B/D ASS’Y CODE BN98-00005C ASSY,PCB/MAIN-ST RN15MS-XGD1/0000,EDC,EUROPE

Loc. No. Code No. Description Specification

Others

6 Electrical Parts List

6-12 SyncMaster 570BTFT/580BTFT

Memo

7 Block Diagram

SyncMaster 570BTFT/580BTFT 7-1

TDA8752

GMFC1 GMZ1

VOLUME

TONE CTRL.

LVDS

x 2

TFT

LCD

PANEL

MICOM and CONTROL PART

FRAME

MEMORY

H

V

R

G

B

12V

R

G

B

8

8

8

R

G

B

8

8

8

R

G

B

6

6

6

DOT_CLK

H/V/DOT_CLK

H/V/EN/

DOT_CLK

+5 V_S

+3.3 V_S

VCC

+5 V_PLL

+5 V_ADL

H DOT_CLK H V

LM4863

(Audio

Amp)

Speaker

(SyncMaster 330TFT/530TFT)

Memo

7 Block Diagrams

7-2 SyncMaster 570BTFT/580BTFT

SyncMaster 570BTFT/580BTFT 8-1

8 Wiring Diagram

1
2

11

10

12

3
4
5
6
7
8
9

NC

NC

BRIGHT

BL_EN
NC

GND

GND

12V

5V

GND

12V
NS

CN103

5V (15":12V)

5V (15":12V)

GND

GND

123

3

LVDS_DATA

5

~

20

CN301

1
2
3

4~9

10
11
12
13
14

15

16 ~26

PC_R_IN

PC_B_IN

PC_G_IN

GND

S_RASTER

H_SYNC

GND

SCL

SDA

V_SYNC

GND

CN101

1
2
3

4~9

10
11
12
13
14

15

PC_R_IN

PC_B_IN

PC_G_IN

GND
S_RASTER

H_SYNC

GND

SCL

SDA

V_SYNC

CN101

1
2
3
4
5
6

KEY

LED

VCC

KEY2
GND
GND

CN401

1
2
3
4
5
6

KEY

LED

VCC

KEY2
GND
GND

CN861

CN881

CN862

123

4

123

4

GND

PWR

VCC

LED

PWR

GND

VCC

LED

1

2

12 V

GND

1
2

RIGHT –
RIGHT +

1
2

LEFT –
LEFT +

8
7
6
5
4
3
2
1

LEFT_AMP

GND

RIGHT_AMP

MIC_EN
5 V

RIGHT_IN

5 V
LEFT_IN

CN841

1
2
3
4
5
6
7
8

LEFT_AMP

GND

RIGHT_AMP

MIC_EN

5 V

RIGHT_IN

5 V

LEFT_IN

CN806

CN801

CN815

CN814

123

12 V

12 V

GND

CN102

CN816

1
2

MIC_GND

MIC_SIG

CN805

C-MIC

CN804

MIC_OUT PC_AUDIO EXT_MIC HEADPHONE

CN808 CN809 CN812 CN813

LCD PANEL

MAIN PCB

MAINFUNC PCB

POWER PCB

SMPS

AUDIO FUNC PCB

123

123

4

NEUTRAL

GND

LIVE

NC

5

NEUTRAL

GND

NC

LIVE

SyncMaster 570BTFT/580BTFT

9-2

SyncMaster 570BTFT/580BTFT

9-4

SyncMaster 570BTFT/580BTFT

1
2
3
4
5
6
7
8

NC
NC
NC

GND

4.43

4.46

4.87

5.03

pin #

MODES

1024 x 768 / 75 Hz

Table 9-8. IC403

Unit: Vrms

1
2
3
4
5
6
7
8

GND
GND
GND
GND

5.03

5.03
GND

5.03

pin #

MODES

1024 x 768 / 75 Hz

Table 9-9. IC404

Unit: Vrms

11
12
13
14
15
16
17
18
19
20
21

5

NC

5

5
Pulse
Pulse

5

NC

NC
Pulse
Pulse

Clock
Clock

5

NC

3.8
5
0
5
5

GND

NC

32
33
34
35
36
37
38
39
40
41
42

Unit: Vrms

5-1 SyncMaster 570STFT/ 580STFT

5 Exploded View and Parts List

5-1 Simple base (570STFT)

5-2 MultiMedia base (570STFT)

5 Exploded View & Parts List

SyncMaster 570STFT/ 580STFT 5-2

10 Schematic Diagrams

5-3 SyncMaster 570STFT/ 580STFT

5-3 Pivot-MultiMedia base (570STFT)

5 Exploded View & Parts List

SyncMaster 570STFT/ 580STFT 5-4

5-4 Angle Pivot base (570STFT)

10 Schematic Diagrams

5-5 SyncMaster 570STFT/ 580STFT

5-5 Wire-frame base (570STFT)

5-6 Simple base (580STFT)

5 Exploded View & Parts List

SyncMaster 570STFT/ 580STFT 5-6

10 Schematic Diagrams

5-7 SyncMaster 570STFT/ 580STFT

5-7 MultiMedia base (580STFT)

5-8 Pivot-MultiMedia base (580STFT)

5 Exploded View & Parts List

SyncMaster 570STFT/ 580STFT 5-8

5-9 Angle Pivot base (580STFT)

10 Schematic Diagrams

5-9 SyncMaster 570STFT/ 580STFT

5-10 Wire-frame base (580STFT)

5 Exploded View & Parts List

SyncMaster 570STFT/ 580STFT 5-10

9-1 SyncMaster 570STFT/580STFT

9 Schematic Diagrams

9-1 DAC & IO Part Schematic Diagram

5

7

6

9 Schematic Diagrams

SyncMaster 570STFT/580STFT 9-2

5

IC201 #94

CH1 RMS = 3.5 V

6

IC106 #9

CH1 RMS = 3.1 V

7

IC105, #1

CH1 RMS = 4.56 V

9-2 ZOOM & FRC Part Schematic Diagram

9 Schematic Diagrams

9-3 SyncMaster 570STFT/580STFT

8

1

11

11

9

2

3

4

9 Schematic Diagrams

SyncMaster 570STFT/580STFT 9-4

2

IC304 #25

CH1 RMS = 2.8 V

3

IC304 #26

CH1 RMS = 2.12 V

4

CN301 #1~16

CH1 RMS = 1.18 V

8

IC301 #141

CH1 RMS = 2.3 V

9

IC303 #20

CH1 RMS = 1.24 V

10

IC303 #22

CH1 RMS = 400 mV

11

IC303 #34

CH1 RMS = 4.4 V

1

IC303 #39

CH1 RMS = 3.6 V

12

IC302 #12

CH1 RMS = 2.2 V

13

IC302 #5

CH1 RMS = 1.7 V

14

IC302 #10

CH1 RMS = 4.3 V

9-3 Micom Part Schematic Diagram

9 Schematic Diagrams

9-5 SyncMaster 570STFT/580STFT

1
2
3
4
5
6
7
8

NC
NC
NC

GND

4.43

4.46

4.87

5.03

pin #

MODES

1024 x 768 / 75 Hz

Table 9-8. IC403

Unit: Vrms

1
2
3
4
5
6
7
8

GND
GND
GND
GND

5.03

5.03
GND

5.03

pin #

MODES

1024 x 768 / 75 Hz

Table 9-9. IC404

Unit: Vrms

1
2
3
4
5
6
7
8

9
10
11
12
13
14
15
16
17
18
19
20
21

0~5
0, 5

5
5

4.62
0
5
5

GND

5
5

NC

5
5

Pulse
Pulse

5

NC

NC
Pulse
Pulse

Pulse
GND
Pulse

5
5
0
0
5
5

0
Clock
Clock

5

NC

3.8
5
0
5
5

GND

NC

22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42

pin #

pin #

MODES

1024 x 768 / 75 Hz 1024 x 768 / 75 Hz

MODES

Table 9-7. IC401

Unit: Vrms

Samsung Electronics Co., Ltd. September 1999
Printed in Korea
Code No.: BN68-00084A