800 - SAMSUNG (800-726786)www.samsung.com/cz
Samsung Zrt., česká organizační složka, Oasis Florenc, Sokolovská394/17, 180 00, Praha 8
30 - 6227 515
3260 SAMSUNG(7267864, € 0,15/Min)
0825 08 65 65 (€ 0.15/Min)
0 - 801 - 1SAMSUNG(172678)
022 - 607 - 93 - 33
Customer Care Centre
www.samsung.com/fi
www.samsung.com/fr
www.samsung.com/pl
Web Site
Plasma TV
user manual
BN68-01757J-01
imagine the possibilities
Thank you for purchasing this Samsung product.
To receive more complete service, please register
your product at
www.samsung.com/global/register
Model Serial No.
Page 2
User Instructions
Screen Image retention
Do not display a still image (such as on a video game or when hooking up a PC to this PDP) on the plasma monitor panel for
more than 2 hours as it can cause screen image retention. This image retention is also known as “screen burn”. To avoid such
image retention, reduce the degree of brightness and contrast of the screen when displaying a still image.
Height
The PDP can normally operate only under 2000m in height. It might abnormally function at a place over 2000m in height so do
not install and operate there.
Heat on the top of the PDP TV
The top side of the product may be hot after long period of use as heat dissipates from the panel through the vent hole in the
upper part of the product. This is normal and does not indicate any defect or operation failure of the product. However, children
should be prevented from touching the upper part of the product.
The product is making a ‘cracking’ noise.
A ‘cracking’ noise may occur when the product contracts or expands due to a change of surrounding environment such as
temperature or humidity. This is normal and not a defect of the unit.
Cell Defects
The PDP uses a panel consisting of 1,230,000(SD-level) to 3,150,000(HD-level) pixels which require sophisticated technology
to produce. However, there may be few bright or dark pixels on the screen. These pixels will have no impact on the
performance of the product.
Avoid operating the TV at temperatures below 5°C(41°F)
A still image displayed too long may cause permanent damage to the PDP Panel.
Watching the PDP TV in 4:3 format for a long period of time may leave traces of borders displayed on
the left, right and centre of the screen caused by the difference of light emission on the screen. Playing a
DVD or a game console may cause similar effect to the screen. Damages caused by the above effect are
not covered by the Warranty.
Afterimage on the Screen.
Displaying still images from Video games and PC for longer than a certain period of time may produce partial afterimages.
To prevent this effect, reduce the ‘brightness’ and ‘contrast’ when displaying still images.
Warranty
- Warranty does not cover any damage caused by image retention.
- Burn-in is not covered by the warranty.
Installation
Be sure to contact an authorized service centre, when installing your set in a location with heavy dust, high or low
temperatures, high humidity, chemical substance and where it operates continually such as the airport, the train station etc.
Failure to do so may cause a serious damage to your set.
Digital TV (DVB-T) Notice
1. FUNCTIONALITIES RELATED TO DIGITAL TV (DVB) ARE ONLY AVAILABLE IN COUNTRIES OR AREAS WHERE
DVB-T (MPEG
2 AND MPEG4 AVC) DIGITAL TERRESTRIAL SIGNALS ARE BROADCAST. DVB-T is the European
consortium standard for the broadcast transmission of digital terrestrial television. Please check with your local dealer
about the availability of DVB-T service in your area.
2. Although this TV set meets the current DVB-T standards as of [August, 2008], compatibility with future DVB-T digital
terrestrial broadcast cannot be guaranteed.
3. Some Digital TV functions may not be available or operate correctly in some countries or regions.
4. For more information, please contact your local SAMSUNG customer care centre.
Contact SAMSUNG WORLDWIDE
If you have any questions or comments relating to Samsung products, please contact the SAMSUNG
customer care centre. (See back cover for more informations.)
Connecting a USB Device .................................................32
■
Using the WISELINK Pro Function ....................................33
■
Using and Sorting Photo List .............................................35
■
Viewing a Photo or Slide Show .........................................36
■
Using and Sorting the Music List .......................................38
■
Playing a Music .................................................................39
■
Using and Sorting the Movie List .......................................40
■
Playing a Movie File ..........................................................41
■
Deleting the Photo/Music/Movie File .................................42
■
Picture/Music Settings Using WISELINK Pro ....................43
■
Using the Setup Menu .......................................................43
■
NOT
SymbolPressNoteOne-Touch ButtonTOOLS
English - 3
Page 4
Connecting and Preparing Your TV
Checking Parts
Owner’s InstructionsRemote Control/
Cover-Bottom / Screws (2ea)
(PS50A756)
Ferrite Core (Power Cord)
N
The ferrite core is used to shield the cable from interference. When connecting a cable, open the ferrite
core and clip it around the cable near the plug.
AAA Batteries
Holder-Ring (4ea)
(Refer to page 60)
Power CordCloth-CleanWarranty Card/
Program CDFerrite Core for
Power Cord (2ea)
Using the Stand-Base
Two or more people should carry the PDP. Never lay the PDP on the floor
N
because of possible damage to the screen. Always keep the PDP upright.
The PDP can rotate 20 degrees in right and left directions.
N
Safety Guide Manual
(Not available in all locations)
How to assemble the Stand-Base (depending on the model)
Using the 6 screws for securing the stand base and the monitor, firmly
attach the monitor to the stand base.
(The exterior of the set may be different than the picture.)
Warning
Firmly secure the stand to the TV
before moving it, as the stand may
fall and could cause serious injury.
Two or more people should carry the TV.
N
Never lay the TV on the floor because of
possible damage to the screen.
Always store the TV upright.
English - 4
In case of installing your TV on the wall, close the
cover (1) on the stand-base connection part using two
screws for hiding.
-20° ~ 20°
Page 5
English - 5
Viewing the Control Panel
The product colour and shape may vary depending on the model.
N
Front Panel buttons
Touch each button to
operate.
1
SOURCE
Toggles between all the available input sources
(TV, Ext1, Ext
HDMI2/DVI
N
In the on-screen menu, use this button as you would
use the ENTER button on the remote control.
2
MENU
Press to see an on-screen menu of your TV’s features.
– +
3
Press to increase or decrease the volume. In the on-screen
menu, use the –
and ► buttons on the remote control.
C/P.
4
Press to change channels. In the on-screen menu, use
the
buttons on the remote control.
5
POWER INDICATOR
Blinks and turns off when the power is on and lights up in
stand-by mode.
6
REMOTE CONTROL SENSOR
Aim the remote control towards this spot on the TV.
2, AV, S-Video, Component, PC, HDMI1,
, HDMI3, HDMI4, USB, DLNA).
+ buttons as you would use the ◄
C/P. buttons as you would use the ▲ and ▼
7
8 (
Touch the silver sensor below the (
SPEAKERS
POWER)
) mark to turn the TV
on and off.
Silver sensor
Page 6
Viewing the Connection Panel
Rear Panel
1
0
or
Cable Television
Network
or
2
The product colour and shape may vary depending on the model.
N
Whenever you connect an audio or video system to your set, ensure that all elements are switched off.
N
When connecting an external device, match the colour of the connection terminal to the cable.
N
1
POWER IN
Connect the supplied power cord.
2
COMPONENT IN
Audio (AUDIO L/R) and video (Y/P
Component.
3
LAN
Connect a LAN cable to this port to connect to the Network.
4
PC IN(PC) / AUDIO
Connect to the video and audio output jack on your PC.
5
EXT 1, EXT 2
Inputs or outputs for external devices, such as VCR, DVD,
video game device or video disc players.
Input/Output Specification
Connector
EXT 1✔✔✔
EXT 2✔✔Output you can choose.
6
DIGITAL AUDIO OUT (OPTICAL)
V
Connect to a Digital Audio Component.
7
AUDIO OUT(AUDIO R/L)
Connect RCA audio signals from the TV to an external
source, such as Audio equipment.
8
SERVICE
InputOutput
ideo Audio(L/R) RGBVideo + Audio(L/R)
5796
B/PR) inputs for
Only TV or DTV output is
available.
9
HDMI IN 1, 2, 3
- No additional Audio connection is needed for an HDMI to
HDMI connection.
When using an HDMI/DVI cable connection, you must
use the HDMI IN 2 jack.
What is HDMI?
N
-
High Definition Multimedia interface allows the
transmission of high definition digital video data and
multiple channels of digital audio.
-
The HDMI/DVI terminal supports DVI connection to
an extended device with the appropriate cable (not
supplied). The difference between HDMI and DVI is
that the HDMI device is smaller in size, has the HDCP
(High Bandwidth Digital Copy Protection) coding feature
installed, and supports multi - channel digital audio.
DVI IN(HDMI
DVI audio outputs for external devices.
0
ANT IN
75Ω Coaxial connector for Aerial/Cable Network.
Supported modes for HDMI/DVI and Component
HDMI/DVI 50HzXXXOOOO
HDMI/DVI 60HzXOXXOOO
ComponentOOOOOOO
834
2) AUDIO L/R
480i 480p 576i 576p 720p 1080i 1080p
Connector for service.
or
English - 6
Page 7
English - 7
4
Side Panel
1
2
3
4
The product colour and shape may vary depending on the model.
N
1
COMMON INTERFACE Slot
Insert CI (Common Interface) card into the slot.
(refer to page 25)
−
When not inserting
Signal is displayed on the screen.
− The pairing information containing a telephone number, CI
CARD ID, Host ID, and other information will be displayed
in about 2~3 minutes. If an error message is displayed,
please contact your service provider.
−
When the channel information configuration has finished,
the message Updating Completed is displayed, indicating
that the channel list is now updated.
Insert the CI-Card in the direction marked on it.
N
2
HDMI IN 4
Connect to the HDMI jack of a device with HDMI output.
3
WISELINK PRO
Connect a USB mass storage device to view and play photo
files (JPEG), audio files (MP3) and movie files.
You can connect to SAMSUNG’s network wirelessly.
4
S-VIDEO or VIDEO / AUDIO L/R
Video (S-Video or Video) and audio inputs for external
devices, such as a camcorder or VCR.
CI CARD in some channels, Scramble
or
5
5
HEADPHONES JACK
You can connect a set of headphones if you wish to
watch a television programme without disturbing the
other people in the room.
Prolonged use of headphones at a high volume may
N
damage your hearing.
Page 8
Remote Control
You can use the remote control up to a distance of about 23 feet from the TV.
The performance of the remote control may be affected by bright light.
N
1
POWER button
(turns the TV on and off)
2
Selects the TV mode directly.
3
Number buttons for direct channel
access
4
One or more digit channel selection
5
Temporary sound switch-off
6
Available source selection
7
Volume increase
Volume decrease
8
Electronic Program Guide (EPG)
display
9
Use to quickly select frequently used
functions.
0
Control the cursor in the menu
!
Use to see information on the
current broadcast
@
Use these buttons in the Channel
list and WISELINK Pro, etc.
$
Press to select the optional display
and sound modes for sports, cinema
and games.
%
Use these buttons in the Channel
list, WISELINK Pro and Anynet+.
^
ON/OFF
Press to backlight the buttons on the
remote. This function is convenient
for using at night or when the room
is dark. (Using the remote control
with the ON/OFF(
to On will reduce the battery usage
time.)
&
Previous channel
*
Next channel
Previous channel
(
Displays the main on-screen menu
)
This function enables you to view
and play photo (JPEG) , audio
files (MP3) and movie files from an
external device.
a
Returns to the previous menu
b
Exit the on-screen menu
c
Not available
) light button set
d Use this when connecting a
SAMSUNG DMA (Digital Media
Adapter) device through an HDMI
interface and switching to DMA
mode.
(The DMA button is optional.) For
more information on the operating
procedures, refer to the user manual
of the DMA. This button is available
when Anynet+(HDMI-CEC) is On
(see page 54)
e
This function enables you to view
Content Library.
f
Digital subtitle display
Teletext Functions
2
Exit from the teletext display
(depending on the model)
6
Teletext mode selection (LIST/
FLOF)
8
Teletext store
9
Teletext size
!
Teletext reveal
@
Fastext topic selection
#
Teletext display/mix both teletext
information and the normal
broadcast
&
Teletext sub page
*
P :Teletext next page
P
:Teletext previous page
(
Teletext index
a
Teletext hold
b
Teletext cancel
English - 8
Page 9
English - 9
Installing Batteries in the Remote Control
1.
Lift the cover at the back of the remote control upward as shown in the gure.
2. Install two AAA size batteries.
Make sure to match the ‘+’ and ‘–’ ends of the batteries with the diagram
N
inside the compartment.
3.
Close the cover.
Remove the batteries and store them in a cool, dry place if you won’t be
N
using the remote control for a long time.
Using the remote control with the ON / OFF@ light button set to on will
N
reduce the battery usage time.
If the remote control doesn’t work, check the following:
N
1. Is the TV power on?
2. Are the plus and minus ends of the batteries reversed?
3. Are the batteries drained?
4. Is there a power outage or is the power cord unplugged?
5. Is there a special uorescent light or neon sign nearby?
Switching On and Off
The mains lead is attached to the rear of your set.
1.
Plug the mains lead into an appropriate socket.
The standby indicator lights up on your set.
N
. Press the POWERP button on your set.
2
You also can press the POWER
N
The programme that you were watching last is reselected automatically.
N
3.
Press the numeric button (0~9) or channel up / down (< / >) button on the remote control or >C/P.
set.
When you switch the set on for the very rst time, you will be asked to choose language in which the menus are to be
N
displayed.
4.
To switch your set off, press the POWER
P
button or the TV button on the remote control to turn the TV on.
P
button again.
P
< button on your
Placing Your Television in Standby Mode
Your set can be placed in standby mode in order to reduce the power consumption. The standby mode can be useful when you
wish to interrupt viewing temporarily (during a meal, for example).
Press the POWER
1.
The screen is turned off and a red standby indicator appears on your set.
N
2
. To switch your set back on, simply press the POWER
button again.
Do not leave your set in standby mode for long periods of time (when you are away on holiday
N
unplug the set from the mains and aerial.
P
button on the remote control.
P
, numeric buttons (0~9), TV button or channel up / down (< / >)
, for example). It is best to
Page 10
Viewing the Menus
1. With the power on, press the MENU button. The main menu appears on the
screen. The menu’s left side has icons: Picture, Sound, Channel, Setup, Input,
Application.
2. Press the ▲ or ▼ button to select one of the icons. Then press the ENTER
E
button to access the icon’s sub-menu.
3. Press the EXIT button to exit.
The on-screen menus disappear from the screen after about one minute.
N
Using the TOOLS Button
You can use the TOOLS button to select your frequently used functions quickly and
easily. The Tools menu changes depending on which external input mode you are
viewing.
1.
Press the TOOLS button. The Tools menu will appear.
. Press the ▲ or ▼ button to select a menu, then press the ENTER
2
3. Press the ▲ / ▼ / ◄ / ► / ENTER
E
buttons to display, change, or use the
selected items. For a more detailed description of each function, refer to the
Anynet+ (HDMI-CEC)
Picture Size : Auto Wide
Picture Mode : Standard
Sound Mode : Custom
Sleep Timer : Off
SRS TS XT : Off
Energy Saving : Off
Dual l ll : Mono
U
Move E Enter e Exit
Standard
Using the Wheel button
To increase the channel number, turn the wheel clockwise when the Channel
Display is displayed. To decrease the channel number, turn the wheel
counterclockwise.
To turn the volume up, turn the wheel clockwise when the Volume
Control window is displayed. To turn the volume down, turn the wheel
counterclockwise.
To move to a lower menu, turn the wheel clockwise when the menu Display is
displayed. To move to a higher menu, turn the wheel counterclockwise.
English - 10
Page 11
English - 11
Plug & Play Feature
When the TV is initially powered on, basic settings proceed automatically and subsequently.
1.
Press the POWER button on the remote control. The message The Menu
Language, Store Demo, Channels and Time will be set. is displayed.
E
. Press the ENTER
2
automatically displayed. Press the ENTER
button, then Select the OSD Language. menu is
E
button.
The Menu Language, Store Demo, Channels and Time
will be set.
3. Select the appropriate language by pressing the ▲ or ▼ button. Press the
E
ENTER
4. Press the ◄ or ► button to select Store Demo or Home Use, then the ENTER
N
N
N
button to conrm your choice.
E
button.
We recommend setting the TV to Home Use mode for the best picture in your home environment.
Store Demo mode is only intended for use in retail environments.
If the unit is accidentally set to Store Demo mode and you want to return to Home Use (Standard): Press the Volume
button on the TV. When the volume OSD is displayed, press and hold the MENU button on the TV for 5 seconds.
The Screen Saver is activated if there is no remote control key input for longer than 1 minute while Plug & Play is
N
running.
The Screen Saver is activated if there is no operating signal for longer than 15 minutes.
N
5.
Press the ENTER
E
button. Select the appropriate country by pressing the ▲ or ▼ button. Press the ENTERE button to
conrm your choice.
E
6. Press the ▲ or ▼ button to select the channel source to memorize. Press the ENTER
N
Digital & Analogue: Digital and Analogue channels.
button to select Start.
Digital: Digital channels.
Analogue: Analogue channels.
The channel search will start and end automatically.
N
Press the ENTER
N
N
After all the available channels are stored, the message Set the Clock Mode. is displayed.
7
. Press the ENTER
If you select Manual, Set current date and time is displayed. (See page 26)
N
If you have received a digital signal, the time will be set automatically. If not, see page 26 to set the clock.
N
8
. The message Enjoy your viewing is displayed. When you have nished, press the ENTER
E
button at any time to interrupt the memorization process.
E
button. Press the ▲ or ▼ button to select Auto, then Press the ENTERE button.
E
button.
Plug & Play
OK
E Enter
If you want to reset this feature...
Press the MENU button to display the menu. Press the ▲ or ▼ button to select
1.
Setup, then press the ENTER
2. Press the ENTER
E
E
button.
button again to select Plug & Play.
3. Enter your 4 digit PIN number. The default PIN number of a new TV set is
‘0-0-0-0’.
If you want to change PIN number, refer to 23 page.
N
The Plug & Play feature is only available in the TV mode.
N
Channel Control
Storing Channels and channel
Country
❑
Analogue Channel: You can change the country for analogue channels.
Digital Channel: You can change the country for digital channels.
The PIN number input screen appears. Enter your 4 digit PIN number.
N
Setup
Plug & Play
Language : English
Time
Network
Wireless Network Setup
Cable Network Setup
Child
Change PIN
Channel
Country
Auto Store
Manual Store
Full Guide
Mini Guide
Default
Channel List
Channel
►
Selection : Cable
Lock : On
Guide : Mini Guide
Mode : Added Ch.
►
Page 12
Auto Store
❑
You can scan for the frequency ranges available to you (and availability depends on your country). Automatically allocated
programme numbers may not correspond to actual or desired programme numbers.
Digital & Analogue: Digital and Analogue channels.
•
Digital: Digital channels.
•
Analogue: Analogue channels.
•
Scans for all channels with active broadcast stations and stores them in the TV’
N
N
If you want to stop Auto Store, press the ENTER
N
The Stop Auto Store? message will be displayed.
N
Select Yes by pressing the ◄ or ► button, then press the ENTER
N
If a channel is locked using the Child Lock function, the PIN input window appears.
Manual Store
❑
Scans for a channel manually and stores it in the TV’s memory.
N
If a channel is locked using the Child Lock function, the PIN input window appears.
N
Digital Channel
Manual store for digital channels.
Channel: Set the Channel number using the ▲, ▼ or number (0~
•
Frequency: Set the frequency using the number buttons.
•
Bandwidth: Set the bandwidth using the ▲, ▼ or number (0~
•
N
When it has nished, channels are updated in the channel list.
Analogue Channel
Manual store for analogue channel.
Programme (Programme number to be assigned to a channel): Sets the programme number using the ▲, ▼ or number
•
(0~9) buttons.
Colour
•
•
•
•
•
System→Auto/PAL/SECAM/NTSC4.43: Sets the colour system value using the ▲ or ▼ button.
Sound System → BG / DK / I / L: Sets the sound system value using the ▲ or ▼ button.
Channel (When you know the number of the channel to be stored): Press the ▲ or ▼ button to select C (Air channel) or S
(Cable channel). Press the ► button, then press the ▲, ▼ or number (0~
N
You can also select the channel number directly by pressing the number (0~
N
If there is abnormal sound or no sound, reselect the sound standard required.
Search (When you do not know the channel numbers): Press the ▲ or ▼ button to start the search. The tuner scans the
frequency range until the rst channel or the channel that you selected is received on the screen.
Store (When you store the channel and associated programme number): Set to OK by pressing the ENTER
N
Channel mode
-
P (Programme mode): When completing tuning, the broadcasting stations in your area have been assigned to position
numbers from P00 to P99. You can select a channel by entering the position number in this mode.
-
C (Air channel mode): You can select a channel by entering the assigned number to each air broadcasting station in
this mode.
-
S (Cable channel mode): You can select a channel by entering the assigned number for each cable channel in this
mode.
E
button.
E
9) buttons.
9) buttons.
s memory.
button.
9) buttons to select the required number.
9) buttons.
E
button.
Full Guide / Mini Guide
❑
The EPG (Electronic Programme Guide) information is provided by the broadcasters. Programme entries may appear blank
or out of date as a result of the information broadcast on a given channel. The display will dynamically update as soon as new
information becomes available.
For the detailed procedures on using Full Guide and Mini Guide, refer to
N
the descriptions on page 13.
You can also display the guide menu simply by pressing the GUIDE button.
O
(To congure the Default Guide, refer to the descriptions.)
Full Guide:
is displayed which may be scrolled forwards or backwards in time.
Mini Guide:
the current programme onwards according to the programme starting time order.
Displays the programme information as time ordered One hour segments. Two hours of programme information
The information of each programme is displayed by each line on the current channel Mini Guide screen from
English - 12
Page 13
English - 13
Default Guide
❑
Mini Guide / Full Guide:
You can decide whether to display either the Mini
Guide or the Full Guide when the GUIDE button on the remote control is
Channel
Fine Tune
Signal Information
LNA : Off
pressed.
Channel List
❑
For the detailed procedures on using the Channel List, refer to the descriptions
on pages 14~15.
❑
Channel Mode
When the press the P >/< button, Channels will be switched within the selected channel list.
Added Ch.: Channels will be switched within the memorized channel list.
Favourite Ch.: Channels will be switched within the favourite channel list.
Fine Tune
❑
If the reception is clear, you do not have to ne tune the channel, as this is done automatically during the search and store
operation. If the signal is weak or distorted, you may have to ne tune the channel manually.
Fine tuned channels that have been saved are marked with an asterisk * on the right-hand side of the channel number in
N
the channel banner.
E
To reset the ne-tuning, select Reset by pressing the ▲ or ▼ button and then press the ENTER
N
N
Only Analogue TV channels can be ne tuned.
Signal Information
❑
button.
You can get information about the signal status.
If the signal status is poor, the Weak or No Signal message is displayed.
N
While viewing a Digital channel, this function can be selected.
N
The technical information for signal status is displayed.
N
- Frequency / Service ID / Multiplex / Network / Bit error level / Signal Strength
►
LNA→Off/On
❑
If the TV is operating in a weak-signal area, the LNA (Low Noise Amplier) function can improve the reception
(a low-noise preamplier boosts the incoming signal).
While viewing an Analogue channel, this function can be selected.
N
Using the Full / Mini Guide
Full Guide
900 f tn
901 ITV Play
902 Kerrang!
903 Kiss
903 oneword
903 Smash Hits!
▼
Watch
DTV Cable 900 f tn 2:10 Tue 1 Jun
Freshmen On Campus
2:00 - 2:30
No Detailed Information
Today2:00 - 3:003:00 - 4:00
Freshmen O..
Street Hypn..
Mint Extra
Loaded
Fresh 40 with Dynamite MC
The Distillery
Smash Hits! Sunday
Information
No Information
No Information
Kisstory
No Information
Mini Guide +24 Hours Exit
Select a programme by pressing the ▲/▼/◄/► button.
▲/▼/◄/►,
(ENTER)
If the next progrmme is selected, it is scheduled with the clock icon displayed. If the ENTER button is
pressed again, press the ▲/▼/◄/► button to select Cancel Schedules, the scheduling is canceled
with the clock icon gone.
For details about scheduling programmes, refer to the section.
REDToggle between the Mini Guide or Full Guide.
GREEN
YELLOW
Full Guide: Scroll backwards quickly (24 hours).
Mini Guide: Display next page quickly.
Full Guide: Scroll forwards quickly (24 hours).
Mini Guide: Display previous page quickly.
BLUEExit the guide.
INFO button for the detailed information. Channel Number, Running Time, Status Bar, Parental Level,
INFO
Video Quality Information (HD/SD), Sound Modes, Subtitle or Teletext, languages of Subtitle or Teletext
and brief summary of the highlighted programme are included on the detailed information. “…” will be
appeared if the summary is long.
Mini GuideDTV Cable 900 f tn
2:00
2:30
▼
5:00
Watch
Freshmen On Campus
Street Hypnosis
Booze Britain
Information
Full Guide Next Page Exit
Page 14
Managing Channels
Using this menu, you can Add / Delete or set Favourite channels and use the
programme guide for digital broadcasts.
N
Select a channel in the All Channels, Added Channels ,Favourites or
Programmed screen by pressing the ▲ / ▼ buttons, and pressing the
E
ENTER
All Channels:
Added Channels:
Favourites:
Programmed:
button. Then you can watch the selected channel.
Shows all currently available channels.
Shows all added channels.
Shows all favourite channels.
Shows all current reserved programmes.
Mini Guide
Default Guide : Mini Guide
Channel
Channel List
Channel Mode : Added Ch.
Fine Tune
Signal Information
LNA :
Off
N
Using the Colour buttons with the Channel List
-
Red (Channel Type): Toggle between your TV, Radio, Data / Other and All.
-
Green (Zoom): Enlarges or shrinks a channel number.
-
Yellow (Select): Selects multiple channel lists.
-
TOOLS (Option): Displays the Delete (or Add), Add to Favourite (or Delete
from Favourite), Lock (or Unlock), Timer Viewing, Edit Channel Name,
Sort, Edit Channel Number, Select All, Deselect All or Auto Store menu.
(The Options menus may differ depending on the situation.)
N
Channel Status Display Icons
An Analogue channel.
A
A channel set as a Favourite.
♥
\
A locked channel.
c
A channel selected by pressing the yellow button.
(
A programme currently being broadcast.
)
A reserved programme
824 UKTV Gold
Added Channels
825 UKTV style
A
1 C --
A
2 C
A 3 ♥ C
A 4 C
A 5 C
A 6 C
A 7 C
A 8 C
All
Channel Type Zoom Select
--
--
--
--
--
--
--
Option
Channel List Option Menu (in All Channels / Added Channels / Favourites)
N
Press the TOOLS button to use the option menu.
N
Option menu items may differ depending on the channel status.
Add / Delete
You can delete or add a channel to display the channels you want.
All deleted channels will be shown on All Channels menu.
N
A gray-coloured channel indicates the channel has been deleted.
N
The Add menu only appears for deleted channels.
N
You can also delete a channel in the Added Channels or Favourites menu
N
in the same manner.
Add to Favourite / Delete from Favourite
You can set channels you watch frequently as favourites.
The ♥ symbol will be displayed and the channel will be set as a favourite.
N
All favourite channels will be shown on Favourites menu.
N
Lock / Unlock
You can lock a channel so that the channel cannot be selected and viewed. This function is available only when the Child
Lock is set to on. (see page 23)
The PIN number input screen appears. Enter your 4 digit PIN number.
N
The default PIN number of a new TV set is 0-0-0-0. You can change the PIN, by selecting Change PIN from the menu.
N
The \ symbol will be displayed and the channel will be locked.
N
Timer Viewing
If you reserve a programme you want to watch, the channel is automatically switched to the reserved channel in the Channel
List; even when you are watching another channel. To reserve a programme , set the current time rst. (See page 26.)
Only memorized channels can be reserved.
N
You can set the channel, month, day, year, hour and minute directly by pressing the number buttons on the remote
N
control.
Reserving a programme will be shown on Programmed menu.
N
Digital Programme Guide and Viewing Reservation
N
When a digital channel is selected, and you press the ► button, the Programme Guide for the channel appears.
reserve a programme according to the procedures described above.
824 UKTV Gold
All Channels
825 UKTV style
A
1 C --
A
2 C
A 3 C
A 4 C
A 5 C
A 6 C
A 7 C
A 8 C
All
Channel Type Zoom Select
--
--
--
--
--
--
--
Delete
Add to Favourite
Lock
Timer Viewing
Edit Channel Name
Sort
▼
Option
You can
English - 14
Page 15
English - 15
Edit Channel Name (only analogue channel)
Channels can labeled so that their call letters appear whenever the channel is selected.
The names of digital broadcasting channels are automatically assigned and cannot be labeled.
N
Edit Channel Number (only digital channel)
You can also edit the channel number by pressing the number buttons on the remote control.
Sort
This operation allows you to change the programme numbers of the stored channels. This operation may be necessary after
using the auto store.
The function is only available in Analouge.
N
Select All / Deselect All
Select All: You can select all the channels in the channel list.
•
Deselect All: You can deselect all the selected channels in the channel list.
•
You can perform the add / delete, add to Favourites / delete from Favourites, or lock / unlock function for multiple
N
channels at the same time. Select the required channels and press the yellow button to set all the selected channels at
the same time.
The c mark appears to the left of the selected channels.
N
You can only select Deselect All when there is a selected channel.
N
Auto Store
For further details on setting up options, refer to page 11.
N
If a channel is locked using the Child Lock function, the PIN input window appears.
N
Channel List Option Menu (in Programmed )
You can view, modify or delete a reservation.
N
Press the TOOLS button to use the option menu.
Change Info: Select to change a viewing reservation.
Cancel Schedules: Select to cancel a viewing reservation.
Information: Select to view a viewing reservation. (You can also change
the reservation information.)
SelectAll: Select all reserved programmes.
Tint(G/R): Adjusts the Colour tint of the picture.
Select a picture mode to be adjusted rst. The adjusted values are saved for each picture mode.
N
When you make changes to Cell Light, Contrast, Brightness, Sharpness, Colour or Tint(G/R), the OSD will be
N
adjusted accordingly.
In Analogue TV, Ext., AV, S-Video modes of the PAL system, you cannot use the Tint Function.
N
In PC mode, you can only make changes to Cell Light, Contrast and Brightness.
N
Settings can be adjusted and stored for each external device you have connected to an input of the
N
N
The energy consumed during use can be signicantly reduced if the level of brightness of the picture is reduced, and then
TV.
this will reduce the overall running cost.
Detailed Settings
❑
Samsung’s new TVs allow you to make even more precise picture settings than
previous models. See below to adjust detailed picture settings.
Detailed Settings is available in Standard or Movie mode.
N
In PC mode, you can only make changes to Dynamic Contrast, Gamma
N
and White Balance from among the Detailed Settings items.
BlackAdjust→Off/Low/Medium/High
Colour : 50
Tint (G / R) : G50 / R50
Picture
DetailedSettings ►
Picture Options
Picture Reset
You can select the black level on the screen to adjust the screen depth.
DynamicContrast→Off/Low/Medium/High
You can adjust the screen contrast so that the optimal contrast is provided.
Gamma
You can adjust the Primary Colour (Red, Green, Blue) Intensity.
Colour Space
Colour Space is a colour matrix composed of red, green and blue colours. Select your favourite Colour Space to experience
the most natural colour.
Auto: Auto Colour Space automatically adjusts to the most natural colour tone based on programme sources.
•
Native: Native Colour Space offers deep and rich colour tone.
•
Custom: Adjusts the colour range to suit your preference.
•
Customizing the Colour Space
N
Colour
-
→Red/Green/Blue/Yellow/Cyan/Magenta
-
Adjusts the Colour range to suit your preference. Colour is available when Colour Space is set to Custom.
-
Red / Green / Blue: In Colour, you can adjust the RGB values for the selected colour.
-
Reset: Resets the colour space to the default values.
White Balance
You can adjust the colour temperature for more natural picture colours.
R-Offset / G-Offset / B-Offset / R-Gain / G-Gain / B-Gain: Changing the adjustment value will refresh the adjusted screen.
•
Reset: The previously adjusted white balance will be reset to the factory defaults.
•
Flesh Tone
You can emphasize the pink ‘esh tone’ in the picture.
Changing the adjustment value will refresh the adjusted screen.
N
EdgeEnhancement→Off/On
You can emphasize object boundaries in the picture.
xvYCC→Off/On
Setting the xvYCC mode to on increases detail and colour space when watching movies from an external device (i.e. DVD
player).
xvYCC is available when the picture mode is set to Movie, and the external input is set to HDMI or Component mode.
N
If xvYCC function is active, PIP cannot be selected.
N
Picture Options
❑
In PC mode, you can only make changes to the Colour Tone, Size and
N
Screen Burn Protection from among the items in Picture Options.
Colour Tone→Cool2 / Cool1 / Normal / Warm1 / Warm2
You can select the most comfortable colour tone to your eyes.
The adjusted values are stored according to the selected Picture mode.
N
Warm1 or W
N
arm2 is only activated when the picture mode is Movie.
English - 16
Tint (G / R) : G50 / R50
Detailed Settings
Picture
PictureOptions►
Picture Reset
Page 17
English - 17
Size
You can select the picture size which best corresponds to your viewing requirements.
Press the TOOLS button to display Tools menu.
T
You can also set the size by selecting T
Auto Wide: Automatically adjusts the picture size to the 1
•
16:9: Adjusts the picture size to 16:9 appropriate for DVDs or wide broadcasting.
•
Wide Zoom: Magnify the size of the picture more than 4:3.
•
Zoom: Magnies the 16:9 wide picture (in the vertical direction) to t the screen size.
•
4:3: This is the default setting for a video movie or normal broadcasting.
•
Just Scan: Use the function to see the full image without any cutoff when HDMI (720p / 1080i / 1080p)
•
ools→PictureSize.
6:9 aspect ratio.
or Component (1080i / 1080p) signals are input.
Depending on the input source, the picture size options may vary.
N
The items available may differ depending on the selected mode.
N
In PC Mode, only 1
N
N
Settings can be adjusted and stored for each external device you have connected to an input of the
N
Temporary image retention may occur when viewing a static image on the set for more than two hours.
N
Wide Zoom: Press the ► button to select Position, then press the ENTER
move the screen up / down. Then press the ENTER
N
Zoom: Press the ► button to select Position, then press the ENTER
picture up and down. Then press the ENTER
6:9 and 4:3 mode can be adjusted.
E
E
button. Press the ► button to select Size, then press the ENTER
button.
TV.
E
button. Press the ▲ or ▼ button to
E
button. Press the ▲ or ▼ button to move the
E
button. Press the ▲ or ▼ button to magnify or reduce the picture size in the vertical direction. Then press the
E
ENTER
N
After selecting Just Scan in HDMI (1080i / 1080p) or Component (1080i / 1080p) mode: Select Position by pressing
button.
the ◄ or ►button. Use the ▲, ▼, ◄ or ► button to move the picture.
E
N
Reset: Press the ◄ or ► button to select Reset, then press the ENTER
N
If you use the Just Scan function with HDMI 720p input, 1 line will be cut at the top, bottom, left and right as in the
button. You can initialize the setting.
overscan function.
N
When Double (
Screen Mode→16:9 / Wide Zoom / Zoom / 4:3
, ) mode has been set in PIP, the Picture Size cannot be set.
When setting the picture size to Auto Wide in a 16:9 wide TV, you can determine the picture size you want to see the 4:3
WSS (Wide Screen Service) image or nothing. Each individual European country requires different picture size so this function
is intended for users to select it.
16:9: Sets the picture to 16:9 wide mode.
•
Wide Zoom: Magnify the size of the picture more than 4:3.
•
Zoom: Magnify the size of the picture vertically on screen.
•
4:3: Sets the picture to 4:3 normal mode.
•
This function is available in Auto Wide mode.
N
This function is not available in PC, Component or HDMI mode.
N
Digital NR→Off / Low / Medium / High / Auto
If the broadcast signal received by your TV is weak, you can activate the Digital Noise Reduction feature to help reduce any
static and ghosting that may appear on the screen.
When the signal is weak, select one of the other options until the best picture is displayed.
N
DNIe→Off / Demo / On
This TV includes the DNIe function so as to provide a high visual quality. If you set DNIe to on, you can view the screen with
the DNIe feature activated. If you set the DNIe to Demo, you can view the applied DNIe and normal pictures on the screen, for
demonstration purposes. Using this function, you can view the difference in the visual quality.
DNIe™ (Digital Natural Image engine)
N
DNIe™
This feature brings you more detailed image with 3D noise reduction, detail enhancement, contrast enhancement and white
enhancement. New image compensation Algorithm gives brighter, clearer, more detailed image to you. DNIe™ technology will
t every signal into your eyes.
N
This function is not available in Movie and Standard mode.
HDMI Black Level→Normal / Low
You can directly select the black level on the screen to adjust the screen depth.
This function is active only when the external input connects to HDMI (RGB signals).
N
Page 18
Real100HzDemo→Off/On
You can get a clear distinction between Real 100Hz and 50Hz, especially when watching fast moving scenes. Therefore, when
seeing slow moving scenes, you will not be able to distinguish between Real 100Hz and 50Hz. Demo 100Hz works only with
50Hz signal. Real 100Hz demo mode is provided for shop demonstration with special pictures.
Movie Plus→Off / Low / Medium / High / Demo
You can view more natural skin and clear text even in fast moving scenes.
Use this function when watching movies.
N
This function is not available in Wide Zoom and Zoom modes.
N
This function is not available when PIP is set to On.
N
It is not supported in HDMI 1080p/24Hz, 25Hz, 30Hz mode.
N
Blue Only Mode→Off / On
This function is for AV device measurement experts. This function displays the blue signal only by removing the red and
green signals from the video signal so as to provide a Blue Filter effect that is used to adjust the Colour and Tint of video
equipment such as DVD players, Home Theaters, etc. Using this function, you can adjust the Colour and Tint to preferred
values appropriate to the signal level of each video device using the Red / Green / Blue / Cyan / Magenta / Yellow Colour Bar
Patterns, without using an additional Blue Filter.
Blue Only Mode is available when the picture mode is set to Movie or Standard.
N
Screen Burn Protection
To reduce the possibility of screen burn, this unit is equipped with screen burn prevention technology. This technology enables
you to set picture movement up/down (Vertical Line) and side to side (Horizontal Dot). The Time setting allows you to program
the time between movement of the picture in minutes.
Pixel Shift: Using this function, you can minutely move pixels on the PDP in horizontal or vertical direction to minimize after
•
image on the screen.
Set Pixel Shift to On by pressing the ▲ or ▼ button, then press the ENTER button.
N
Select the required option by pressing the ▲ or ▼ button, then press the ENTER button.
N
Available options: Horizontal Dot, Vertical Line, Time.
N
Optimum condition for pixel shift;
N
PCTV/Ext/AV/Component/HDMI
Horizontal Dot44
Vertical Line44
Time (minute)42 min
N
The Pixel Shift value may differ depending on the monitor size (inches) and mode.
N
This function is not available in the Just Scan mode.
•
All White: This function helps remove after images on the screen by changing the colour of pixels to white. Use this
function when there are remaining after images or symbols on the screen especially when you displayed a still image on the
screen for a long time.
•
Scrolling: This function helps remove after images on the screen by moving all the pixels on the PDP according to a
pattern Use this function when there are remaining after images or symbols on the screen especially when you displayed a
still image on the screen for a long time.
•
Side Gray: When you watch TV with the screen ratio of 4:3, the screen is prevented from any damage by adjusting the
white balance on both extreme left and right sides.
-
Dark: When you set the screen ratio to 4:3, it darkens the left and right sides.
-
Light: When you set the screen ratio to 4:3, it brightens the left and right sides.
PictureReset→ResetPictureMode/Cancel
❑
Resets all picture settings to the default values.
Select a picture mode to be reset. The reset is performed for each picture mode.
N
English - 18
Page 19
English - 19
Viewing Picture-in-Picture
You can display a sub picture within the main picture of set programme or video
input. In this way, you can watch the picture of set programme or video input from
any connected equipment while watching the main picture.
You may notice that the picture in the PIP window becomes slightly unnatural
N
when you use the main screen to view a game or karaoke.
Press the TOOLS button to display Tools menu.
T
You can also congure PIP related settings by selecting T
PIP→Off / On
❑
You can activate or deactivate the PIP function.
Main pictureSub picture
Component
HDMI 1, HDMI2/DVI, HDMI 3,
HDMI 4
TV, Ext.1, Ext.2, AV
PC
Source
You can select a source of the sub-picture.
Size → / /
You can select a size of the sub-picture.
If main picture is in HDMI mode, Size is available.
N
Position → / / /
You can select a position of the sub-picture.
In Double (
N
Channel
, ) mode, Position cannot be selected.
You can select a channel of the sub-picture only when the Source is set to TV.
Press the TOOLS button to display Tools menu.
T
You can also set the picture mode by selecting T
ools→PIP.
ools→PIP
Entertainment : Off
Energy Saving : Off
Setup
PIP►
Software Upgrade
Common Interface
PIP
PIP : On
Source : TV
Size :
Position :
Channel : ATV 11
L
Move E Enter R Return
Setting up the TV with your PC
Preset: Press the SOURCE button to select PC mode.
N
Auto Adjustment
❑
Auto Adjustment allows the PC screen of set to self-adjust to the incoming PC
video signal. The values of ne, coarse and position are adjusted automatically.
This function does not work in DVI-HDMI mode.
N
Press the TOOLS button to display Tools menu.
T
You can also set the Auto Adjustment by selecting T
ools→Auto
Adjustment.
Screen
❑
Coarse / Fine:
The purpose of picture quality adjustment is to remove or reduce picture noise. If the noise is not removed
by Fine-tuning alone, then adjust the frequency as best as possible (Coarse) and Fine-tune again. After the noise has been
reduced, readjust the picture so that it is aligned on the center of screen.
PC Position:
Adjust the PC’s screen positioning if it does not t the TV screen.
Press the ▲ or ▼ button to adjusting the
Vertical-Position. Press the ◄ or ► button to adjust the Horizontal-Position.
Image Reset:
You can replace all image settings with the factory default values.
Picture
Brightness : 45
Sharpness : 50
Auto Adjustment
Screen
Detailed Settings
Picture Options
Picture Reset
►
Page 20
PC Display
Setting Up Your PC Software (Based on Windows XP)
The Windows display-settings for a typical computer are shown below. The actual
screens on your PC will probably be different, depending upon your particular
version of Windows and your particular video card. However, even if your actual
screens look different, the same basic set-up information will apply in almost all
cases. (If not, contact your computer manufacturer or Samsung Dealer.)
1. First, click on ‘Control Panel’ on the Windows start menu.
2
. When the control panel window appears, click on ‘Appearance and Themes’
and a display dialog-box will appear.
3. When the control panel window appears, click on ‘Display’ and a display dialog-
box will appear.
4.
Navigate to the ‘Settings’ tab on the display dialog-box.
The correct size setting (resolution)
Optimum: 1920 X 1080 pixels
If a vertical-frequency option exists on your display settings dialog box, the
correct value is ‘60’ or ‘60 Hz’. Otherwise, just click ‘OK’ and exit the dialog box.
Display Modes
Both screen position and size will vary depending on the type of PC monitor and its resolution.
The resolutions in the table are recommended.
D-Sub Input
ModeResolution
IBM
VESA
CVT1920 x 1080RB66.58759.934138.500+ / -
640 x 350
720 x 400
640 x 480
640 x 480
640 x 480
800 x 600
800 x 600
800 x 600
1024 x 768
1024 x 768
1024 x 768
1280 x 1024
1280 x 1024
1360 x 768
1600 x 1200
Horizontal
Frequency (kHz)
31.469
31.469
31.469
37.861
37.500
37.879
48.077
46.875
48.363
56.476
60.023
63.981
79.976
47.712
75.000
Vertical Frequency
(Hz)
70.086
70.087
59.940
72.809
75.000
60.317
72.188
75.000
60.004
70.069
75.029
60.020
75.025
60.015
60.000
Frequency (MHz)
Pixel Clock
25.175
28.322
25.175
31.500
31.500
40.000
50.000
49.500
65.000
75.000
78.750
108.000
135.000
85.500
162.000
Sync Polarity
(H / V)
+ / -
- / +
- / -
- / -
- / + / +
+ / +
+ / +
- / -
- / + / +
+ / +
+ / +
+ / +
+ / +
HDMI / DVI Input
ModeResolution
640 x 480
800 x 600
VESA
CEA1920 x 1080p67.500 60.000148.500 + / +
When using an HDMI / DVI cable connection, you must use the HDMI IN
N
The interlace mode is not supported.
N
The set might operate abnormally if a non-standard video format is selected.
N
Separate and Composite modes are supported. SOG is not supported.
N
Too long or low quality VGA cable can cause picture noise at high resolution modes (1920x1080).
N
1024 x 768
1280 x 1024
1360 x 768
1600 x 1200
Horizontal
Frequency (kHz)
31.469
37.879
48.363
63.981
47.712
75.000
English - 20
Vertical Frequency
(Hz)
59.940
60.317
60.004
60.020
60.015
60.000
2 jack.
Pixel Clock
Frequency (MHz)
25.175
40.000
65.000
108.000
85.500
162.000
Sync Polarity
(H / V)
- / + / +
- / + / +
+ / +
+ / +
Page 21
English - 21
Sound Control
Changing the Sound Standard
Mode→Standard/Music/Movie/Speech/Custom
❑
You can select the type of special sound effect to be used when watching a
given broadcast.
Press the TOOLS button to display Tools menu.
T
You can also congure the sound mode by selecting T
ools→Sound
Mode.
Equalizer
❑
The sound settings can be adjusted to suit your personal preferences.
Mode: You can select a sound mode to suit your personal preferences.
Balance: Controls the balance between the right and left speakers.
100Hz / 300Hz / 1kHz / 3kHz / 10kHz (Bandwidth Adjustment): To adjust the level of different bandwidth frequencies
Reset: Resets the equalizer settings to the default values.
SRSTruSurroundXT→Off/On
❑
TruSurround XT is a patented SRS technology that solves the problem of playing 5.1 multichannel content over two speakers.
TruSurround delivers a compelling, virtual surround sound experience through any two-speaker playback system, including
internal television speakers. It is fully compatible with all multichannel formats.
Press the TOOLS button to display Tools menu.
T
You can also set the SRS TruSurround XT by selecting T
ools→SRSTSXT.
TruSurround XT, SRS and Symbol are trademarks of SRS Labs, Inc. TruSurround XT
technology is incorporated under license from SRS Labs, Inc.
Sound
Mode : Custom
Equalizer
SRS TruSurround XT : Off
Audio Language : ---Audio Format : ----
Audio Description
Auto
Volume : Off
Select Speaker : TV Speaker
►
Audio Language
❑
You can change the default value for audio languages. Displays the language information for the incoming stream.
While viewing a digital channel, this function can be selected.
N
You can only select the language among the actual languages being broadcast.
N
AudioFormat→MPEG/DolbyDigital
❑
When sound is emitted from both the main speaker and the audio receiver, a sound echo may occur due to the decoding
speed difference between the main speaker and the audio receiver. In this case, use the TV Speaker function.
While viewing a digital channel, this function can be selected.
N
You can only select the language among the actual languages being broadcast.
N
Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are
trademarks of Dolby Laboratories.
Audio Description
❑
This is an auxiliary audio function that provides an additional audio track for visually challenged persons. This function handles
the Audio Stream for the AD (Audio Description), when it is sent along with the Main audio from the broadcaster. Users can
turn the Audio Description On or Off and control the volume.
AudioDescription→Off/On: Turn the audio description function on or off.
Volume: You can adjust the audio description volume.
Volume is active when Audio Description is set to On.
N
While viewing a Digital channel, this function can be selected.
N
Page 22
Auto Volume→Off/On
❑
Each broadcasting station has its own signal conditions, and so it is not easy
to adjust the volume every time the channel is changed. This feature lets you
automatically adjust the volume of the desired channel by lowering the sound
output when the modulation signal is high or by raising the sound output when
the modulation signal is low.
❑
SelectSpeaker→ExternalSpeaker/TVSpeaker
If you want to hear the sound through separate speakers, cancel the internal
amplier.
The –
N
If you select External Speaker in the Select Speaker menu, the sound settings will be limited.
N
+, MUTE buttons do not operate when the TV Speaker is set to Off.
TV's Internal SpeakersAudio Out (Optical, L / R Out) to Sound System
TV / Ext. / AV / S-Video / Component / PC / HDMITV / Ext. / AV / S-Video / Component / PC / HDMI
TV SpeakerSpeaker OutputSound Output
External SpeakerMuteSound Output
Video No SignalMuteMute
Sound Select
❑
When the PIP feature is activated, you can listen to the sound of the sub (PIP) picture.
Main: Used to listen to the sound of the main picture.
Sub: Used to listen to the sound of the sub picture.
Press the TOOLS button to display Tools menu.
T
You can also set the sound of the sub picture by selecting Tools→PIP→SoundSelect.
Sound Reset
❑
Reset All / Reset Sound Mode / Cancel:
You can restore the Sound settings to the factory defaults.
Select Speaker : TV Speaker
Sound Select : Main
Sound
SoundReset►
Selecting the Sound Mode
You can set the sound mode in the Tools menu. When you set to Dual l ll, the
current sound mode is displayed on the screen.
Type of broadcast
Regular broadcast
(Standard audio)
Regular + NICAM Mono
NICAM
Stereo
A2
Stereo
If the stereo signal is weak and an automatic switching occurs, then switch to the mono.
N
This function is only activated in stereo sound signal. It is deactivated in mono sound signal.
N
This function is only available in TV mode.
N
NICAM-Stereo
NICAM Dual-I/II
Regular broadcast
(Standard audio)
Bilingual or DUAL-I/II
StereoStereo
On-screen indication
Mono (Normal use)
NICAM
NICAM
Stereo
NICAM
Dual-1
Mono (Normal use)
Dual IDual II
NICAM
Dual-2
(Forced mono)
English - 22
Mono
(Normal)
Mono
(Normal)
Mono
(Normal)
Mono
Tools
Anynet+ (HDMI-CEC)
Picture Size : Auto Wide
Picture Mode : Standard
Sound Mode : Custom
Sleep Timer : Off
SRS TS XT : Off
Energy Saving : Off
Dual l ll ◄ Mono ►
U
Move L Adjust e Exit
Page 23
English - 23
Function Description
ConguringtheSetupMenu
❑
Language
You can set the menu language.
❑
ChildLock→Off/On
This feature allows you to prevent unauthorized users, such as children, from
watching unsuitable programmes by muting out video and audio.
Before the setup screen appears, the PIN number input screen appears.
N
Enter your 4 digit PIN number.
The default PIN number of a new TV set is 0-0-0-0. You can change the
N
PIN by selecting Change PIN from the menu.
You can lock some channels in Channel List. (refer to page 14)
N
Child Lock is available only in TV mode. .
N
❑
Change PIN
You can change your personal ID number that is required to set up the TV.
Before the setup screen appears, the PIN number input screen appears. Enter your 4 digit PIN number
N
N
The default PIN number of a new TV set is 0-0-0-0.
N
If you forget the PIN code, press the remote control buttons in the following sequence, which resets the PIN to 0-0-0-0:
POWER (Off), MUTE, 8, 2, 4, POWER (On).
❑
ParentalLock→ParentalRating
This feature allows you to prevent unauthorized users, such as children, from watching unsuitable programmes by a 4-digit
PIN (Personal Identication Number) code that is dened by the user.
In the Parental Rating screen, congure the parental ratings.
-
Before the setup screen appears, the PIN number input screen appears. Enter your 4 digit PIN number
N
The default PIN number of a new TV set is 0-0-0-0. You can change the PIN by selecting Change PIN from the menu.
N
When the parental ratings are set, the
N
Allow All: Press to unlock all TV ratings.
N
Block All: Press to lock all TV ratings.
\
symbol is displayed.
Plug & Play
Setup
Language : English ►
Time
Network Selection : Cable
Wireless Network Setup
Cable Network Setup
Child
Lock : On
Change PIN
Parental Lock
.
.
❑
Subtitle
You can activate and deactivate the subtitles. Use this menu to set the Subtitle Mode. Normal under the menu is the basic
subtitle and Hard of hearing is the subtitle for a hearing-impaired person.
Subtitle→Off/On: Switches subtitles off or on.
Mode→Normal/Hardofhearing: Sets the subtitle mode.
Subtitle Language: Set the subtitle language.
N
If the programme you are watching does not support the Hard of hearing function, Normal automatically activates even
though Hard of hearing mode is selected.
N
English is the default in cases where the selected language is unavailable in the broadcast.
N
You can select these options simply by pressing the SUBT. button on the remote control.
❑
Teletext Language
You can set the Teletext language by selecting the language type.
English is the default in cases where the selected language is unavailable
N
in the broadcast.
Page 24
Preference
❑
Primary Audio Language / Secondary Audio Language / Primary Subtitle Language / Secondary Subtitle Language /
Primary Teletext Language / Secondary Teletext Language
Using this feature, users can select one of the languages. The language selected here is the default when the user selects a
channel.
If you change the language setting, the Subtitle Language, Audio Language, and the Teletext Language of the Language
menu are automatically changed to the selected language.
The Subtitle Language, Audio Language, and the Teletext Language of the Language menu show a list of languages
supported by the current channel and the selection is highlighted. If you change this language setting, the new selection is
only valid for the current channel. The changed setting does not change the setting of the Primary Subtitle Language, Primary
Audio Language, or the Primary Teletext Language of the Preference menu.
DigitalText→Disable/Enable
❑
If the programme is broadcast with digital text, this feature is enabled.
MHEG (Multimedia and Hypermedia Information Coding Experts
N
Group)
An International standard for data encoding systems used in multimedia
and hypermedia. This is at a higher level than the MPEG system which
includes data-linking hypermedia such as still images, character service,
animation, graphic and video les as well as multimedia data. MHEG is
user runtime interaction technology and is being applied to various elds
including VOD (Video-On-Demand), ITV (Interactive TV), EC (Electronic
Commerce), tele-education, tele-conferencing, digital libraries and network
You can turn on/off the blue LED on the front of TV according to the situation. Use it for saving power or when the LED dazzles
your eyes.
Off: The blue LED is always off.
In Standby: The blue LED lights while in Standby mode and it turns off when your TV is turned on.
Watching TV: The blue LED lights when watching TV and it turns off when your TV is turned off.
Always: The blue LED always lights.
Set the Light Effect to Off to reduce the power consumption.
N
Melody
❑
Off / Low / Medium / High
The TV power on / off melody sound can be adjusted.
The Melody does not play
N
When no sound is output from the TV because the MUTE button has been pressed.
When no sound is output from the TV because the –
-
-
When the TV is turned off by Sleep Timer function.
Entertainment
❑
(Volume) button has been pressed.
The Entertainment mode enables you to select the optimal display and sound for sports, cinema and games.
Off: Switches the Entertainment function off.
Sports: Provides the optimal picture and sound quality for sports.
Cinema: Provides the optimal picture and sound quality for movie watching. You can experience a richer picture and
enhanced sound.
Game: Provides the optimal picture and sound quality for games. This mode accelerates the playing speed when
using an external game console connected to the TV.
If you set any of the three Entertainment modes to On, the settings will be locked and can not be adjusted. In addition,
N
Picture and Sound mode settings are not allowed. If you want to make Picture and Sound mode adjustments, the
Entertainment mode must be turned off.
The Entertainment settings are saved for each input source.
N
Entertainment mode is not activated in PC mode.
N
You can press the E.MODE button on the remote control repeatedly to change
O
the Entertainment setting.
English - 24
Page 25
English - 25
Energy Saving
4
❑
This feature adjusts the brightness of the TV in order to reduce power consumption. When watching TV at night, set the
Energy Saving mode option to High to reduce eye fatigue as well as power consumption.
Off: Turns off the energy saving function.
Low: Sets the TV to low energy saving mode.
Medium: Sets the TV to medium energy saving mode.
High: Sets the TV to high energy saving mode.
Press the TOOLS button to display Tools menu.
T
You can also set the Energy Saving option by selecting Tools→EnergySaving.
Software Upgrade
❑
To keep your product up-to-date with new Digital Television features then
TV Side Panel
software upgrades are periodically broadcast as part of the normal Television
signal. It will automatically detect these signals and display the software
upgrade banner. You are given the option to install the upgrade.
BY USB
USB Drive
Insert a USB drive containing the rmware upgrade into TV. Please be careful
to not disconnect the power or remove the USB drive while upgrades are being
applied. The TV will turn off and turn on automatically after completing the
rmware upgrade. Please check the rmware version after the upgrades are complete. When software is upgraded, video and
audio settings you have made will return to their default (factory) settings. We recommend you write down your settings so that
you can easily reset them after the upgrade.
BY Channel
Upgrades the software using the broadcasting signal.
Standby Mode Upgrade
To continue software upgrade with master power on, Select On by pressing the ▲ or ▼ button. 45 minutes after entering
standby mode, a manual upgrade is automatically conducted. Since the power of the unit is turned on internally, the screen
may be on slightly for the product. This phenomenon may continue for more than 1 hour until the software upgrade is
completed.
Alternative Software
To display the software version information.
Common Interface
❑
Installing the CI Card
a. Purchase the CI CAM module by visiting your nearest dealer or by phone.
b. Insert the CI CARD into the CAM in the direction of the arrow until it ts.
c. Insert the CAM with the CI CARD installed into the common interface slot.
Insert the CAM in the direction of the arrow, right up to the end so that it is
N
parallel with the slot.
d. Check if you can see a picture on a scrambled signal channel.
CI Menu
This enables the user to select from the CAM-provided menu.
Select the CI Menu based on the menu PC Card.
Application Info.
This contains information on CAM inserted in the CI slot and displays it.
The Application Info inserting is about the CI CARD. You can install the CAM
anytime whether the TV is ON or OFF.
1. Purchase the CI CAM module by visiting your nearest dealer or by phone.
2
. Insert the CI CARD into the CAM in the direction of the arrow until it ts.
3. Insert the CAM with the CI CARD installed into the common interface slot. (Inser
t the CAM in the direction of the arrow, right
up to the end so that it is parallel with the slot.)
4. Check if you can see a picture on a scrambled signal channel.
Page 26
Setting the Time
Clock
❑
Setting the clock is necessary in order to use the various timer features of the
TV.
The current time will appear every time you press the INFO button.
N
If you disconnect the power cord, you have to set the clock again.
N
Clock Mode
You can set up the current time manually or automatically.
Auto: Set the current time automatically using the time from the digital
•
broadcast.
Manual: Set the current time to a manually specied time.
•
Clock Set
You can set the current time manually.
Set up this item when you have set Clock Mode to Manual.
N
You can set the day, month, year, hour, minute directly by pressing the
Three different on / off timer settings can be made.
On Time:
Set the hour, minute, and Activate / Inactivate.
(To activate timer with the setting you’ve chosen, set to Activate.)
Off Time:
Set the hour, minute, and Activate / Inactivate.
(To activate timer with the setting you’ve chosen, set to Activate.)
Volume:
Contents:
Set the required volume level.
When the On Timer is active, you can turn on a specic channel or play back contents such as photo or audio
les.
TV / USB: Select TV or USB. (Make sure that an USB device is connected to your TV.)
•
Antenna: Select ATV or DTV.
•
Channel: Select the desired channel.
•
Music: Select the folder containing MP3 les on the USB device.
•
Photo: Select the folder containing JPEG les on the USB device.
•
Repeat:
Select Once, Everyday, Mon~Fri, Mon~Sat, Sat~Sun, or Manual.
When Manual is selected, press the ► button to select the desired day of the week. Press the ENTER
N
E
button over the
desired day and the c mark will appear.
You must set the clock rst.
N
You can set the hour, minute and channel by pressing the number buttons on the remote control.
N
Auto Power Off
N
When you set the timer On, the television will eventually turn off, if no controls are operated for 3 hours after the
TV was
turned on by the timer. This function is only available in timer On mode and prevents overheating, which may occur if a TV is
on for too long time.
English - 26
Page 27
English - 27
Network Connection
Network Connection - Cable
Cable Connection for a DHCP Environment
The procedures to set up the network using Dynamic Host Conguration Protocol (DHCP) are described below. Since an IP
address, subnet mask, gateway, and DNS are automatically allocated when DHCP is selected, you do not have to enter them
manually.
TV Rear Panel
The Modem Port
on the Wall
1. Connect the [LAN] port on the rear panel of the TV and the external modem with a LAN Cable.
2. Connect the LAN port on the wall and the external modem with a Modem Cable.
You can connect the LAN via a Sharer (Router).
External Modem
(ADSL/VDSL/Cable TV)
Modem Cable
2
IP Sharer
LAN Cable
1
The Modem Port
on the Wall
You can connect the LAN port and the TV directly depending on your network status.
The LAN Port
on the Wall
The terminals (the position of the port and the type) of the external device may differ depending on the manufacturer.
N
If the IP address allocation by the DHCP server has failed, turn the external modem off, turn it on again after at least 10
N
External Modem
(ADSL/VDSL/
Cable TV)
Modem Cable
LAN Cable
LAN Cable
LAN Cable
TV Rear Panel
TV Rear Panel
seconds and then try again.
For the connections between the external modem and the Sharer (Router), refer to the owner
N
’s manual of the corresponding
product.
N
You can connect the TV to the LAN directly without connecting it through a Sharer (Router).
N
You cannot use a manual-connection-type ADSL modem becaus;e it does not support DHCP. You have to use an automatic-
connection-type ADSL modem.
Page 28
LAN Connection for Static IP Environment
The procedures to set up the network using a static IP address are described below. You have to manually enter the IP
address, subnet mask, gateway, and DNS that are provided by your Internet Service Provider (ISP).
TV Rear Panel
The LAN Port
on the Wall
LAN Cable
1
1. Connect the [LAN] port on the rear panel of the TV and the LAN port on the wall using the LAN cable.
You can connect the LAN via a Sharer (Router).
The LAN Port
on the Wall
LAN Cable
The terminals (the position of the port and the type) of the external device may differ depending on the manufacturer.
N
If you are using a static IP address, your ISP will inform you of the IP address, subnet mask, gateway, and DNS. You must
N
IP Sharer
LAN Cable
TV Rear Panel
enter these values to complete the network settings. If you do not know the values, ask your network administrator
N
For the information on how to congure and connect a Sharer (Router), refer to the owner
’s manual for the corresponding
product.
N
You can connect the TV to the LAN directly without connecting it through a Sharer (Router).
N
If you use an IP Sharer (IP Router) that supports DHCP, you can set up the device as either DHCP or static IP.
N
For the procedures to use a static IP address, ask your Internet Service Provider.
.
Network Connection - Wireless
You can connect to the network wirelessly through a wireless IP sharer.
TV Side Panel
The LAN Port
on the Wall
Wireless IP sharer
LAN Cable
1. Connect the ‘Samsung Wireless LAN Adapter into the Wiselink terminal of the TV.
N
You must use the ‘Samsung Wireless LAN Adapter (WIS-08BG) to use a wireless network.
N
The ‘Samsung Wireless LAN Adapter is sold separately. Contact a Samsung Electronics agent or service center for
purchasing.
N
To use a wireless network, your TV must be connected to a wireless IP sharer.
N
If the wireless IP sharer supports DHCP, you TV can use a DHCP or static IP address to connect to the wireless network.
N
You must use a wireless IP sharer that supports IEEE 802.11 B or IEEE 802.11G.
N
If the wireless IP sharer allows you to turn on / off the Ping connection function, turn it on.
N
Set the wireless IP sharer to Infrastructure mode. Ad-hoc mode is not supported.
N
Select a channel for the wireless IP sharer that is not currently being used. If the channel set for the wireless IP sharer is
currently being used by another device nearby, this will result in interference and communications may fail.
N
When applying the security key for the AP (wireless IP sharer), only the following is supported.
1) Authentication Mode : WEP, WPAPSK, WPA2PSK
2) Encryption Type : WEP, TKIP, AES
If you apply a security system other than the systems listed above, it will not work with the
Samsung Wireless LAN
Adapter
TV.
English - 28
Page 29
English - 29
Network Setup
Network Selection
❑
Select Cable or Wireless as the method to connect to the network.
The menu is activated only if the ‘Samsung Wireless LAN Adapter’ is
You can test or conrm the network connection status after setting up the network.
If your Internet service provider has registered the MAC address of the device used to connect to the Internet for the rst
time and authenticates the MAC address each time you connect to the Internet, your
the Internet as the MAC address differs from that of the device (PC) used to connect to the Internet the rst time. In this
case, ask your Internet service provider about the procedures to connect devices other than your PC (such as your TV) to
the Internet. If your Internet service provider requires an ID or password to connect to the Internet (network), your TV may
not be able to connect to the Internet. In this case, you have to enter your ID or password when connecting to the Internet
using an Internet Sharer (Router).
The internet connection may fail due to a rewall problem. In this case, contact your Internet service provider
cannot connect to the Internet even if you have followed the procedures of your Internet service provider, please contact a
Samsung Electronics Service Center.
Network Test: You can test or confirm the network connection status after setting up the network.
When unable to connect to a wireless network
N
Your TV may fail to locate an AP that is congured as a private SSID type. In this case, please change the AP settings and
try again. If your Internet service provider has registered the MAC address of the device used to connect to the Internet
for the rst time and authenticates the MAC address each time you connect to the Internet, your
connect to the Internet as the MAC address differs from that of the device (PC) used to connect to the Internet the rst
time. In this case, ask your Internet service provider about the procedures to connect devices other than your PC (such
as your TV) to the Internet. If you cannot connect to the Internet even if you have followed the procedures of your Internet
service provider, please contact a Samsung Electronics Service Center.
Select Access Point:
If a wireless Access Point is not in the Access Point list, press the Red button.
N
When the connection is made, you will be returned to the screen automatically.
N
If you selected an Access Point that requires security authentication, enter the security key.
N
If you have selected an Access Point with a security authentication:
N
The Security Key input screen appears.
-
Enter the security key and press the ENTERE button.
Using the Remote Control Buttons on the Security Key Input Screen.
-
Setup Screen can be different depending on the security types.
N
You can select the IP sharer to use when using a wireless network.
Language : English
Time
Setup
NetworkSelection :Cable►
Wireless Network Setup
Cable Network Setup
Child
Lock : On
Change PIN
Parental Lock
Subtitle
T
eletext Language : - - - -
TV may not be able to connect to
TV may not be able to
. If you
ButtonOperations
▲/▼/◄/►,
(Wheel)
(ENTER)
Red button
Green button
Blue button
Moves the selection up/down/left/right.
Enters (Inputs) the selected character.
Switch between Upper- and Lower-Case Letters
You can delete an already entered character.
Press this button to nish entering the security key.
Page 30
Cable Network Setup-Auto Setup
If you connect the LAN cable and it supports DHCP, the Internet Protocol (IP) Settings are automatically congured. Please check
if the LAN cable is connected. (See page 27)
Set Network Selection to Cable.
1.
2
. Select Cable Network Setup.
3.
Set Internet Protocol Setup to Auto Setup.
4.
Select Network Test to check the network connectivity.
Cable Network Setup-Manual Setup
To connect the TV to the LAN using a static IP address, you must set up the Internet Protocol (IP). Please check if the LAN cable is
connected. (See page 27)
1. Set Network Selection to Cable.
2
. Select Cable Network Setup.
3.
Set Internet Protocol Setup to Manual Setup.
4.
Set up IP Address, Subnet Mask, Gateway and DNS Server.
Press the number buttons on the remote control when you set the Network manually
N
5. Select Network Test to check the network connectivity.
.
Wireless Network Setup-Auto Setup
The menu is activated only if the ‘Samsung Wireless LAN Adapter for is connected. (See page 28)
If you connect the LAN cable and it supports DHCP, the Internet Protocol (IP) Settings are automatically congured. The wireless
IP sharer to be connected to this product must support DHCP.
Set Network Selection to Wireless.
1.
2
. Select Wireless Network Setup.
3.
Set Internet Protocol Setup to Auto Setup.
4.
Select an AP through Select Access Point.
5.
Select Network Test to check the network connectivity.
Wireless Network Setup-Manual Setup
The menu is activated only if the ‘Samsung Wireless LAN Adapter for is connected. (See page 28)
1. Set Network Selection to Wireless.
2
. Select Wireless Network Setup.
3.
Set Internet Protocol Setup to Manual Setup.
4.
Select an AP through Select Access Point.
5.
Select Network Test to check the network connectivity.
English - 30
Page 31
Source List / Edit Name
Source List
❑
Use to select TV or other external input sources such as DVD players or Cable
Box / Satellite receivers (Set-Top Box) connected to the TV. Use to select the
You can choose only those external devices that are connected to the TV.
N
In the Source List, connected inputs will be highlighted and sorted to the
top. Inputs that are not connected will be sorted to the bottom.
Using the Colour buttons on the remote with the Source list
N
Red (Refresh): Refreshes the connecting external devices.
TOOLS (Option): Displays the Edit Name and Information menus.
-
Press the SOURCE button on the remote control to view an external signal
O
source. TV mode can be selected by pressing the TV button, number
buttons (0~
Edit Name
❑
VCR / DVD / Cable STB / Satellite STB / PVR STB / AV Receiver / Game / Camcorder / PC / TV / IPTV / Blu-Ray / HD
9), and the P < / > button on the remote control.
DVD / DMA
Name the device connected to the input jacks to make your input source selection easier.
When a PC with a resolution of 1920 x 1080@60Hz is connected to the HDMI IN
N
mode to PC in the Edit Name of the Input mode.
Input
Source List
Edit Name
2 port, you should set the HDMI2 / DVI
Product Guide
The Product Guide gives you information on the most important features of this TV.
1.
Press the MENU button to display the menu. Press the ▲ or ▼ button to select
Application, then press the ENTER
2. Press the ▲ or ▼ button to select Product Guide, then press the ENTER
button.
3. Press the ◄ or ► button to select a Guide (Picture Quality, Entertainment or
Connectivity) and press the ENTER
4. You can navigate the Product Guide screen by using the ◄ and ► buttons.
Picture QualityFull HD 1080p
EntertainmentContent Library
ConnectivityWISELINK Pro
Press the EXIT button to exit.
5.
E
button.
E
button.
Ultra FilterBright
Real 100Hz(50") / 100Hz Dual Scan(63")
Entertainment Mode
DLNA
4HDMI
Anynet+
English - 31
E
Anynet+ (HDMI-CEC)
Application
Content Library
ProductGuide►
Page 32
Using the Remote Control Button in Product Guide Menu
4
ButtonOperations
Yellow buttonShows the contents of the Product Guide sequentially. (AutoPlay)
▲/▼/◄/►
(Wheel)
E
ENTER
Move the cursor and select an item.
Select the currently selected item.
RETURNReturn to the previous menu.
EXITStop the current function and return to the Product Guide main menu.
,
P
PRE-CH
Stop Product Guide mode and Returns to TV mode
WISELINK Pro
Connecting a USB Device
1. Press the POWER button to turn the TV on.
2. Connect a USB device containing photo, music and/or movie les to the
WISELINK jack (USB jack) on the side of the TV.
If you enter the WISELINK Pro mode with no USB device connected the
N
message ‘No external storage device found. Check the connection status.’
will appear. In this case, insert the USB device, exit the screen by pressing
the W.LINK button on the remote control and enter the WISELINK Pro screen
again.
MTP (Media Transfer Protocol) is not supported.
N
The le system only supports FAT16/32 (The NTFS le system is not supported).
N
Certain types of USB Digital camera and audio devices may not be compatible with this
N
N
WISELINK Pro only supports USB Mass Storage Class devices (MSC). MSC is a Mass Storage Class Bulk-Only
TV.
device. Examples of MSC are Thumb drives and Flash Card Readers (Both USB HDD and HUB are not supported.)
N
Please connect directly to the USB port of your TV. If you are using a separate cable connection, there may be a USB
compatibility problem.
N
Before connecting your device to the TV, please back up your les to prevent them from damage or loss of data. SAMSUNG is
not responsible for any data le damage or data loss.
N
Do not disconnect the USB device while it is loading.
N
MSC supports MP3 and JPEG les, while a PTP device supports JPEG les only.
N
The sequential JPEG format is supported.
N
The higher the resolution of the image, the longer it takes to display on the screen.
N
The maximum supported JPEG resolution is 15360X8640 pixels.
N
For unsupported or corrupted les, the Not Supported File Format message is displayed.
N
If the number of photo les exceeds 4000 (or the number of music les exceeds 3000), any les exceeding the 4000 limit may
not be displayed in the Photo List (or Music List).
N
MP3 les with DRM that have been downloaded from a non-free site cannot be played. Digital Rights Management (DRM)
is a technology that supports the creation of content, the distribution and management of the content in an integrated and
comprehensive way, including the protection of the rights and interests of the content providers, the prevention of the illegal
copying of contents, as well as managing billings and settlements.
N
When moving to a photo, loading may take a few seconds. At this point, the loading icon will appear at the screen.
TV Side Panel
USB Drive
Transport
English - 32
Page 33
English - 33
Using the WISELINK Pro Function
This function enables you to view and listen to photo, music and/or movie les saved on a USB Mass Storage Class (MSC) device.
Entering the WISELINK Pro Menu
1. Press the MENU button. Press the ▲ or ▼ button to select Application, then press the ENTERE button.
2. Press the ▲ or ▼ button to select WISELINK Pro, then press the ENTER
E
button.
The WISELINK Pro menu is displayed.
N
Press the W.LINK button on the remote control to display the WISELINK
O
Pro menu.
Press the SOURCE button on the remote control repeatedly to select USB
O
or DLNA, then press the ENTER
3.
Press the Red button, then press the ▲ or ▼ button to select the
corresponding USB Memory Device (i.e. if connected through a hub). Press the
E
ENTER
N
button.
This function differs depending on the USB Memory Device/ DLNA device
E
button.
connected to TV.
The selected USB device name appears at the bottom left of the screen.
N
4.
Press the ◄ or ► button to select an icon (Photo, Music, Movie, Setup), then
press the ENTER
E
button. To exit WISELINK Pro mode, press the W.LINK
button on the remote control.
You can enjoy game movies. (Not support game program)
N
WISELINK Pro
Photo
SUM
PHOTO
MusicSetup
SUM
Movie
851.98MB/995.00MB Free
Device Return
Removing a USB Memory Device Safely
You can remove the device safely from the TV.
Press the TOOLS button in the WISELINK Pro le list screen, or while a Slide
1.
Show or music le is being played.
2
. Press the ▲ or ▼ button to select Remove Safely, then press the ENTER
Play Current Group
Delete
Information
Remove Safely
▲
Select
Jump
Option
Page 34
Screen Display
Photo
image_1.jpg
Month : Jan
Date :
Color : Gray
Composition :
Folder : P-other
Favourites :
Jan.01.2008
★ ★ ★
1
26
1File(s) Selected
SUM
Preference
Monthly
Timeline
57
34
JanNov
Device
Favourites Settings
▲
Select
Jump
Option
1. Currently selected le: The currently selected le is highlighted. Photo and movie les are displayed as thumbnail images.
2. Information Window: Shows information about the currently selected le. There is a separate information window for photo and
movie les only. For music les, the le information is also displayed in the location where the le is displayed.
3.
Current Sort Standard: This eld shows the current standard for sorting les. Press the ▲ or ▼ button to change the standard
for sorting les.
4.
View Groups: Shows the sorting groups. The sorting group including the currently selected photo is highlighted.
5.
Current Device: Shows the currently selected device name. Press the Red button to select a device.
6
. Item Selection Information: Shows the number of photos that are selected by pressing the
Yellow button.
7. Help Items
Red (Device) button: Selects a connected device.
•
Green (Favourites Settings) button: Changes the Favourites Settings for the selected le. Press this button repeatedly
•
until the desired value appears.
Yellow (Select) button: Selects le from the le list. Selected les are marked with a symbol c. Press the yellow button
•
again to cancel a le selection.
πµ (Jump) button: Jumps to the previous sorting group/Jumps to the next sorting group.
•
•
(Option) button: Displays the option menus. (The option menu changes according to the current status.)
TOOLS
Using the Remote Control Button in WISELINK Pro Menu
ButtonOperations
▲/▼/◄/►
(Wheel)
E
ENTER
RETURNReturn to the previous menu.
TOOLSRun various functions from the Photo, Music and Movie menus.
INFOShow le information.
W.LINKExit WISELINK Pro mode.
,
P
PRE-CH
EXITStop the current function and return to the WISELINK Pro main menu.
Move the cursor and select an item.
Select the currently selected item.
While playing a slide show, movie, or music le:
- Pressing the ENTER
- Pressing the ENTER
E
button during play pauses the play.
E
button during pause resumes the play.
Play or pause the Slide Show or Music le.
Stop the current slide show, Music or Movie le.
Jump to previous group/Jump to next group.
Stop WISELINK Pro mode and Returns to TV mode.
English - 34
Page 35
English - 35
Using and Sorting Photo List
You can sort photos in the Photo List by a particular standard.
1.
Press the ▲ or ▼ button to select a sorting standard in the Photo list.
N
The photos are sorted according to the newly selected sorting standard.
N
To move to the previous/next group, press the
π
(REW) or µ (FF)
Photo
button.
2. Press the
∂
(Play)/ENTERE button to start the Slide Show in the order
selected by the user.
The information of a photo le is automatically set.
N
The Color and Composition information extracted from a photo le
N
may be different from the user’s expectations.
Photo information is automatically set. You can change the Color,
N
SUM
Preference
Monthly
Timeline
Composition, and Favourites.
Photos for which information cannot be displayed are set as
N
Unclassied.
PTP does not support folder sort mode.
N
Sorting Standard for the Photo List
Monthly
It sorts and shows photos in the le by month. It sorts only by month (from January to December) regardless of year.
Timeline
It sorts and shows photos by date. It sorts by year and month from the earliest photo.
Color
It sorts photos by color. You can change the photo color information.
Color options: Red, Yellow, Green, Blue, Magenta, Black, Gray, Unclassied.
N
Composition
It sorts photos by composition. You can change the compositional information of photos.
Composition options:
N
Folder
It sorts photos by folder. If there are many folders in USB, the photos les are shown in order in each folder. The photo le in
the Root folder is shown rst and the others are shown in alphabetical order by name.
Preference
It Sorts photos by preference (Favourites). You can change the photo preferences.
Changing the Favourites Settings.
N
Select the desired photo in the Photo list, then press the Green button repeatedly until the desired setting appears.
Favourites options:
1. Press the ◄ or ► button to select the desired photo in the Photo list.
2 . Press the yellow button. Repeat the above operation to select multiple photos.
c
The
N
N
N
3.
Press the
O
mark appears to the left of the selected photo.
If you select one le, the Slide Show will not be performed.
To deselect all selected les, press the TOOLS button and select Deselect All.
∂
(Play)/ENTERE button.
The selected les will be used for the Slide Show.
English - 36
Page 37
English - 37
Slide Show Option Menu
Stop Slide Show / Start Slide Show
You can start or stop a Slide Show.
Rotate
You can rotate photos saved on a USB memory device.
Whenever you press the ◄ button, it rotates by 270˚, 180˚, 90˚, and 0˚.
N
Whenever you press the ► button, it rotates by 90˚, 180˚, 270˚, and 0˚.
N
Zoom
You can magnify photos saved on a USB memory device. (x1 → x2 → x4)
To move the enlarged photo image, press the ENTER
N
E
button, then
press the ▲/▼/◄/► buttons. Note that when the enlarged picture
is smaller than the original screen size, the location change function
doesn’t work.
The enlarged le is not saved.
N
If you have select Rotate, the Zoom deactivated.
N
Slide Show Speed
You can select the slide show speed.
You can select the Slide Show speed only during a slide show.
N
You can also change the speed of the Slide Show by pressing the
N
BackgroundMusic→On/Off
π
(REW) or µ (FF) button during the Slide Show.
If you set Background Music to On, the background music will be played when viewing photos one by one or in a Slide
Show.
If you set Background Music to On, a screen appears immediately where you can set the Background Music.
To use this feature, there must be music and photo les stored on the USB device.
Background Music Setting
You can select background music when watching a Slide Show.
If you turn off the Background Music, even if the Background Music Settings have been set up, the background music
N
will not be played.
Loading music les is needed to change BGM mode. Play music les in music category to load.
N
BGM
•
Mode→Mood/SelectedFile/Shufe
•
BGMMood→Energetic/Rhythmical/Sad/Exciting/Calm
N
If you set BGM Mode to Mood, you can select a mood.
N
You cannot select a mood not part of the music les on the USB memory device.
•
Select Music File
N
If you set BGM Mode to Selected File, you can select a music le.
Picture Setting / Sound Setting
Refer to page 43.
Information
The photo le information is displayed.
Remove Safely
You can remove the device safely from the TV.
Stop Slide Show
Rotate
Zoom
Slide Show Speed : Normal
Background Music : Off
Background Music Setting
Picture Setting
Sound Setting
Information
U
Move E Enter e Exit
Tools
Page 38
Using and Sorting the Music List
You can sort music les in the Music List by a particular standard.
1.
Press the ▲ or ▼ button to select a sorting standard in the Music list.
N
Music les are sorted according to the newly selected sorting standard.
N
To move to the previous/next group, press the π (REW) or µ (FF)
button.
2. Press the ENTER
E
button to start playing music in the order selected by
the user.
N
The information of the music les is automatically set.
N
The Mood information extracted from a music le may differ from the
expectations of the user.
N
Music information is automatically set. You can change the Mood and
Favourites.
N
Music les for which information cannot be displayed are set to Unclassied.
N
If there is no title information for a music le, the lename is displayed.
N
If no information is available for the Genre, Artist, Album, or Year, the corresponding item is displayed as blank.
Sorting Standard for the Music List
Title: It sorts the Music titles in alphabetical order, and shows the music file.
Artist: It sorts the music file by artist in alphabetical order.
Mood: It sorts music files by the mood. You can change the music mood information.
Mood options: Energetic, Rhythmical, Sad, Exciting, Calm, Unclassied
N
Genre: It sorts music files by the genre.
Folder: It sorts music files by the folder. If there are many folders in USB, the files are shown in order in each folder.
The music file in the Root folder is shown first and the others are shown in alphabetical order by name.
Preference: It sorts music files by preference (Favourites). You can change the music files preferences.
Changing the Favourites Settings
N
Select the desired music le in the Music list, then press the Green button repeatedly until the desired setting appears.
To change the information of multiple les, select les by pressing the yellow button.
N
Favourites options:
N
★ ★ ★, ★ ★ ★, ★ ★ ★, ★ ★ ★
Music
Thanks
Jee
Album 1
2005
Pop
Energetic ★ ★ ★
Preference
Title
Artist
Device
SUM
I Love You
Darby
Album 2
2005
Pop
Sad ★ ★ ★
F G H IJ L P S T V ▲
Favourites Settings
Select
Calm ★ ★ ★
Jump
Better than yesterday
Catherine
Album 3
2005
Pop
Option
Music List Option Menu
Play Current Group: Using this menu, you can only play music files in
the currently selected sorting group.
Delete: Using this menu, you can delete the selected music files.
Change Group: You can change the mood information of music files.
The group information of the current file is updated and the file is
moved to the new group.
To change the information of multiple les, select les by pressing the
N
yellow button.
Information: The music file information including the name, the size,
the date modified and the path is displayed.
You can view the information of music les during a Slide Show using
N
the same procedures.
Alternatively, select a music le from the music list and press the INFO
O
button to view the information.
Remove Safely: You can remove the device safely from the TV.
Music
Thanks
Jee
Album 1
2005
Pop
Sad ★ ★ ★
Artist
Mood
Genre
Device
SUM
I Love You
Darby
Album 2
2005
Pop
Sad ★ ★ ★
Rhythmical SadExciting Calm ...
▲
Favourites Settings
Play Current Group
Delete
Change Group
Information
Exciting ★ ★ ★
Select
Jump
Better than yesterday
Catherine
Album 32005
Pop
▼
Option
English - 38
Page 39
English - 39
Playing a Music
Playingamusicle
1. Pressing the ◄ or ► button to select a music le to be played.
2. Press the
N
∂
(Play)/ENTERE button.
This menu only shows les with the MP3 le extension. Files with other
le extensions are not displayed, even if they are saved on the same
USB device.
N
π
(REW) or µ (FF) buttons do not function during play.
N
The selected le is displayed at the top with its playing time.
N
To adjust the music volume, press the volume button on the remote
control. To mute the sound, press the MUTE button on the remote
control.
N
The playing duration of a music le may be displayed as ‘00:00:00’ if its playing time information is not found at the start of
the le.
N
Music Play Control Buttons
E
ENTER
∂
∑
N
Music function information icon
Play/Pauses the music le.
Play the music le
Pause the music le
∫
Exit play mode and return to the music list.
TOOLSRun various functions from the Music menus.
When all music les in the folder (or the selected le) are repeated. Repeat Mode is On.
When all music les in the folder (or the selected le) are played once. Repeat Mode is Off.
Playing the music group
1. Press the ▲ or ▼ button to select a sorting standard. (Title, Artist, Mood, Genre, Folder, Preference)
2
.
Press the
3. Press the TOOLS button.
4.
Press the ▲ or ▼ button to select Play Current Group, then press the ENTER
N
π
(REW) or µ (FF) button to select the desired group.
E
The music les in the sorting group including the selected le are played.
7/14 00:01:15 00:05:41
I Love You
SUM
Pause Previous Next Option Return
button.
Playingtheselectedmusicles
1. Press the ◄ or ► button to select the desired music le in the music list.
2. Press the yellow button. Repeat the above operation to select multiple music les.
c
N
The
mark appears to the left of the selected music le.
3. Press the
N
∂
(Play)/ENTERE button.
Only the selected le is played.
Music Play Option Menu
RepeatMode→On/Off
You can play music les repeatedly.
Picture Setting / Sound Setting
Refer to page 43.
Information
The music le information is displayed.
Remove Safely
You can remove the device safely from the TV.
Tools
Repeat Mode
◄ On ►
Picture Setting
Sound Setting
Information
Remove Safely
U
Move L Adjust e Exit
Page 40
Using and Sorting the Movie List
You can sort movies in the Movie List by a particular standard.
1.
Press the ▲ or ▼ button to select a sorting standard in the Movie list.
N
The movie les are sorted according to the newly selected sorting
Movie
standard.
N
To move to the previous/next group, press the
π
(REW) or µ (FF)
button.
N
Movie doesn't support subtitles.
(for example, not support smi, srt and sub les, etc and not support
subtitles included in movie les)
2
. Press the
∂
(Play)/ENTERE button to play the movie in the order
selected by the user.
N
The movies are sorted according to the newly selected sorting standard.
N
Movie information is automatically set. You can change the Favorites.
SUM
Preference
Title
Timeline
Sorting Standard for the Movie List
Title
It sorts and displays the Movie titles in symbol/Number/alphabet/special order.
Timeline
It sorts and shows movies by date. It sorts by year and month from the earliest movie.
Folder
If there are many folders in USB, the movies les are shown in order in each folder. The movie le in the Root folder is shown
rst and the others are shown in alphabetical order by name.
Preference
It sorts movies by preference. (Favourites) You can change the movie preferences.
Changing the Favourites Settings
N
Select the desired movie le in the movie list, then press the Green button repeatedly until the desired setting appears.
Favourites options:
N
Movie List Option Menu
Play Current Group
Using this menu, you can only play movie les in the currently selected
sorting group.
Delete
Using this menu, you can delete the selected movie les.
Information
The movie le information including the order of the le in the current
directory, the name, the size, the date modied and the path is displayed.
O
Alternatively, select a movie le from the movie list and press the INFO
button to view the information.
★ ★ ★, ★ ★ ★, ★ ★ ★, ★ ★ ★
Movie
Preference
Title
Timeline
SUM
movie_1.jpg
Date : Jan.01.2008
Folder : movie-folder
Favourites :
★ ★ ★
SYMBOL
AM
SYMBOL
AM
ENG
□
▲
Device
Favourites Settings
movie_1.jpg
Date : Jan.01.2008
Folder : movie-folder
Favourites :
★ ★ ★
ENG
□
▲
Device
Favourites Settings
Select
Jump
Play Current Group
Delete
Information
Remove Safely
Select
Jump
Option
Option
Remove Safely
You can remove the device safely from the TV.
English - 40
Page 41
English - 41
Playing a Movie File
Playingamoviele
1. Pressing the ◄ or ► button to select a movie to be played.
2. Press the
N
N
N
N
∂
(Play)/ENTERE button.
The selected le is played.
The selected le is displayed at the top with its playing time.
The playing duration of a movie le may be displayed as ‘00:00:00’ if its
playing time information is not found at the start of the le.
Supported Video Formats
Video Codec
File ExtentionContainerVideo DecoderMax Resolution Sti
XviD720x576
MPEG1720x576
MPEG2720x576
*.aviAVI
H.264 BP1920x1088
H.264 BP1920x1088
H.264 HP1920x1088
MPEG-4 SP720x576
MPEG-4 ASP720x576
H.264 BP1920x1088
H.264 MP1920x1088
*.mp4MP4
H.264 HP1920x1088
MPEG-4 SP720x576
MPEG-4 ASP720x576
*.mpg
*.mpegMPEG2 (Program Stream)1920x1088
*.vroMPEG2 VOB1920x1088
PS
MPEG1 (Program Stream)1920x1088
*.vobMPEG2 VRO1920x1088
others
(ts)
TS
MPEG2 (Transport Stream)1920x1088
H.264 (Transport Stream)1920x1088
1/5 00:00:48 00:23:05
ABC.avi
E
SUM
Pause -20sec +20sec Option
Return
N
Video Play Control Buttons
ENTER
∂
∑
∫
TOOLS
E
Play/Pauses the movie le
Play the movie le
Pause the movie le
Exit play mode and return to the movie list.
Run various functions from the movie menus.
◄/►Skip forwards or backwards through the movie le in 20 second intervals.
▲/▼Play the next le or the previous le.
Movie function information icon
N
When all movie les in the folder (or the selected le) are repeated.
Repeat Mode is On.
When all movie les in the folder (or the selected le) are played once.
Repeat Mode is Off.
Playing the movie group
1. Press the ▲ or ▼ button to select a sorting standard. (Title, Timeline, Folder, Preference)
2. Press the π (REW) or µ (FF) button to select the desired group.
3. Press the TOOLS button.
4. Press the ▲ or ▼ button to select Play Current Group, then press the ENTER
E
button.
Page 42
Playingtheselectedmovieles
1. Press the ◄ or ► button to select the desired movie le in the movie list.
2. Press the yellow button. Repeat the above operation to select multiple movie les.
The cmark appears to the left of the selected movie le.
N
3.
Press the ∂ (Play)/ENTER
N
Only the selected le is played.
E
button.
Playing movie continuously
If you exit playing movie, playing it continuously later is possible.
With Play continuously function, you can watch movie without watching again from beginning or bothering searching.
1.
Select movie le you want to Play continuously by pressing ◄ or ► button from the Movie List.
. Press the ∂ (Play)/ENTER
2
E
button.
3. Select play continuously by pressing Blue button.
Movie will begin to play from where it was stopped being played.
N
If Cont. movie play help function was set On, a pop-up message will appear when you play movie le you want to Play
N
continuously. (Refer to page 43)
4.
To exit WISELINK Pro mode, press the W.LINK button on the remote control.
Movie Play Option Menu
Repeat Mode
You can play the movie repeatedly.
Picture Setting / Sound Setting
Refer to page 43.
Picture Size
Fit: Play video at the TV screen size.
•
Original: Play video at the original size.
•
Information
The movie le information is displayed.
Remove Safely
You can remove the device safely from the TV.
Tools
Repeat Mode ◄ On ►
Picture Setting
Sound Setting
Picture Size : Fit
Information
Remove Safely
U
Move L Adjust e Exit
Deleting the Photo/Music/Movie File
1. Press the ◄ or ► button to select the desired le in the Photo/Music/Movie
list.
To delete multiple les, select les by pressing the yellow button.
N
2
. Press the TOOLS button.
3.
Press the ▲ or ▼ button to select Delete (or Delete Selected File), then
press the ENTER
4. Press the ◄ or ► button to select OK, then press the ENTER
The le is deleted.
N
When a read-only le is deleted, the This
N
it? message appear.
N
Read-only les among multiple les cannot be deleted.
N
If you select Cancel, the deletion is cancelled.
N
While removing les, don’t remove the USB memory device.
N
You cannot remove the PTP-connected digital camera picture les.
N
You cannot recover deleted photo/music/movie les.
1. Run the Setup.exe le on the Programme CD supplied with the product.
Alternatively, you can download the le from www.samsung.com.
N
2
. Install the SAMSUNG PC Share Manager as shown in the gures below.
► ►
► ►
►
3. When the installation is complete, the PC Share Manager icon appears on your Desktop.
Double-click the icon to run the programme.
N
Page 46
Using the DLNA Application
Name Modied
Name
Name
Name
Name
Name
Name Modied
Name
Name
Name
YesNo
The Programme Screen Layout
1
2345
67
1. Menus: The following application menus are provided : File, Share, Server, and Help.
2. Click to share the selected PC server folder.
3.
Click to cancel sharing.
4.
Click to refresh the PC folder and les.
5.
Click to synchronize the share status.
6
. The folders and les of the PC to be shared are listed.
7
. Folders shared by the user are listed.
8
. PC server name shown on the device list of the WISELINK Pro: Click to change the name.
8
File
❑
Property: Shows information on the selected file or folder.
Method 1: Select a le or folder and select the File menu and then select the Property sub-menu.
-
Method 2: Select a le or folder, right-click over the selected le or folder and then select Property from the pop-up menu.
-
<Method 1><Method
Exit: Exits the DLNA application.
2>
If you select Exit without applying the changes after changing the shared status, a message will appear asking if you want to
apply the changed settings to the PC. Select Yes to apply the changes and exit the application.
English - 46
Page 47
English - 47
Share
❑
Sharing a Folder
You can share a folder from your PC to the TV. The maximum number of folders that can be shared is 32.
Your PC will operate as a server to the TV.
N
Method 1: Select a folder in My Computer, select the Share menu and then select the Share Folder sub-menu.
-
2: Select a folder in My Computer, right-click over the selected folder and then select Share Folder from the pop-
Method
-
up menu.
Method 3: Locate the mouse pointer over a folder in the My Computer folder list in the left pane and drag&drop the folder
-
into the Shared Folders pane. If a message appears asking you to conrm the shared folder
<Method 1><Method
2><Method 3>
, select Yes.
Cancelling a Shared Folder
You can cancel a shared folder on your PC. Select a folder from the Shared Folder pane and select Unshare Folder.
Method 1: Select a folder from the Shared Folder pane, select the Share menu and then select Unshare Folder.
-
Method
-
-
2: Select a folder from the Shared Folder pane, right-click over the selected folder and then select Unshare Folder
from the pop-up menu.
Method 3: Locate the mouse pointer over a folder in the Shared Folder pane and drag&drop the folder into the My
Computer pane. If a message appears asking you to conrm the cancelation, select Yes.
<Method 1><Method
2><Method 3>
Applying the Current Settings
Perform this when synchronization is necessary due to a new shared folder or canceling a shared folder. The Set Changed
State menu applies changes to shared folders to the data saved with the PC share programme.
Since applying changes to the internal data is a time-consuming process, this function enables users to apply changes to the
data only when required.
Until the Set Changed State menu is selected, the changed state of the shared folder is not applied to the server.
Changes to the shared folders are not applied to your PC until you select the Set Changed State menu.
Method 1: Select the Share menu and select the Refresh DB sub-menu.
-
Method
-
2: Click the Set Changed State icon.
Page 48
Setting the Access Permission
To enable the TV to nd your PC, the TV must be set to Set Device Policy in the Access Permission Settings window. In
addition, the PC server and the TV must be on the same subnet.
Method: Select the Share menu and select Set Device Policy. Rejected items are represented in gray. You can change the
-
access permissions by using the Allow Accept / Deny button. To delete an item, select the item and select Delete Item.
❑
Server
Server
You can run or stop using your PC as a server.
Start Server at Windows start
You can determine whether to start the PC server automatically when Windows starts.
Change server name
You can rename the PC server. Enter a new name and click OK. The new name will appear at the top right of the window and
will appear on the TV.
❑
Help
Version
The programme version information message box appears.
English - 48
Page 49
English - 49
Using the DLNA Function
Using the DLNA Menu
DLNA (Digital Living Network Alliance) enables content saved on a DLNA server
(usually your PC) connected to your TV or over a network to be played.
Wiselink Pro enables playing content saved on a USB memory device connected
to the TV, while DLNA enables playing content saved on a DLNA server (your
PC) connected to your TV or over the network. The procedures to use the
content are the same as those for WISELINK Pro.
If you install the PC share manager programme supplied with the TV onto a PC,
you can have the PC perform the role of a DLNA server over the network.
1.
Press the W.LINK button on the remote control to display the DLNA menu.
2
. Press the ◄ or ►button to select an icon (Photo, Music, Movie, Setup), then
press the ENTER
To exit DLNA mode, press the W.LINK button on the remote control.
N
Photo
❑
Photo List option menu
E
button.
Sorting Photo List/Viewing the Information/Rotating the Photo le/Viewing a Slide Show
During a Slide Show option menu
Play & Pause/Slide Show Speed/Zoom/Rotate
Music
❑
Music List option menu
Sorting Music List/Viewing the Information/Playing a music le
Music Play Option Menu
Play & Pause/Repeat Mode
WISELINK Pro
SUM
Photo
PHOTO
MusicSetup
Movie
Device e Exit
DLNA : Server
Movie
❑
Movie List option menu
Sorting Movie List/Viewing the Information/Playing a Movie le
Movie Play Option Menu
Play & Pause/Repeat Mode
Setup
❑
Slide Show Speed/Music Repeat Mode/Movie Repeat Mode/Screen Saver Run Time/Information
DLNA does not support the following functions.
N
The Background Music and Background Music Setting functions.
-
Sorting les by preference in the Photo, Music, and Movie folders.
The Change Group Info function.
The Delete function.
The Safe Remove function.
The π (REW)/µ (FF) button functions while a movie is playing.
-
The Skip (◄/► button) or Pause function may not work while a movie is playing for the DLNA
N
depending on the corresponding content information.
N
The playing time may not be displayed while a movie is playing.
of other manufacturers,
Page 50
Content Library
Activating the Content Library
The Content Library enables you to view or play the built-in contents on the TV
or stored on your USB device. The Delete, Move and Update functions will not
work with the built-in content on the TV.
1.
Press the MENU button. Press the ▲ or ▼ button to select Application,
then press the ENTER
2. Press the ▲ or ▼ button to select Content Library, then press the
E
ENTER
button.
The Content Library main menu is displayed.
Press the CONTENT button on the remote control to display the Content
N
Library main menu.
3.
Press the ◄ or ► button to select an icon (Gallery, Cooking, Children,
Fitness), then press the ENTER
The selected item will be run.
N
Refer to the explanation for the button in the display when the user uses
N
the button while content is running.
E
button.
E
button.
WISELINK Pro
Application
Anynet+ (HDMI-CEC)
ContentLibrary►
Product Guide
Content Library
Gallery
Gallery
Using the Remote Control Button in Content Library Menu
CookingChildrenFitness
Setup
USB
Return
ButtonOperations
▲/▼/◄/►
(Wheel)
E
ENTER
Move the cursor and select an item.
Select the currently selected item.
RETURNReturn to the previous menu.
EXITStop the current function and return to the Content Library main menu.
P
(colour button)
,
PRE-CH
Stop Content Library mode and Returns to TV mode.
Button that provide functions are described on the corresponding page.
You can control the volume of the played content.
CONTENTExit Content Library mode.
If you press the Volume or MUTE button, no OSD is displayed, but the function operates accordingly.
N
CONTENTS LIBRARY CONTAINS TEXT, GRAPHICS, IMAGES, MULTIMEDIA, AND OTHER MATERIALS FOR
INFORMATIONAL AND PROMOTIONAL PURPOSES ONLY. MATERIALS IN CONTENTS LIBRARY HAS BEEN
MODIFIED AND KEEPS BEING REVISED AND UPDATED. THE MATERIALS IN THE CONTENTS LIBRARY MAY
NOT BE SUITABLE FOR ALL AUDIENCES.
INFORMATION IN THE CONTENTS LIBRARY IS PROVIDED “AS IS.” ALTHOUGH THE INFORMATION
PROVIDED TO YOU IN THE CONTENTS LIBRARY IS OBTAINED OR COMPLIED FROM SOURCES WE
BELIEVE TO BE RELIABLE, SAMSUNG CANNOT AND DOES NOT GUARANTEE THE ACCURACY, VALIDITY,
TIMELINESS OR COMPLETENESS OF ANY INFORMATION OR DATA MADE AVAILABLE TO YOU FOR ANY
PARTICULAR PURPOSE. UNDER NO CIRCUMSTANCES, INCLUDING NEGLIGENCE, SHALL SAMSUNG BE
HELD LIABLE, WHETHER IN CONTRACT OR TORT, FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL OR
CONSEQUENTIAL DAMAGES, ATTORNEY FEES, EXPENSES, OR ANY OTHER DAMAGES WHATSOEVER
ARISING OUT OF, OR IN CONNECTION WITH, ANY INFORMATION CONTAINED IN, OR THE USE OF, THE
CONTENTS LIBRARY, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Exit
English - 50
Page 51
English - 51
Using the Content Library
Gallery
❑
Art/Relaxation/Party:
various atmospheres. Using the Gallery function of the TV, you can change your home atmosphere.
Press the yellow button to playback all imageries.
N
There is default music for each for the Art, Relaxation, and Party options.
N
Press INFO button to see the credit and detail information in English for the imagery. Press INFO button again or press
N
► button for the credit information to go away (currently, the credit supports English only).
The copyrights of the Gallery contents and all issues related to them are reserved by Gallery Player, Inc.
N
For additional Gallery contents, check for information through www.samsung.com. Please refer to the Using Additional
N
Content Using External USB Memory Storage section to see how to play additional imagery.
Cooking
❑
Starters/Main Courses/Desserts:
contents which give you great ideas for meals.
The recipes introduced in the Cooking contents on the Samsung TV are based on recipes published by Anness
N
Publishing.
The copyrights of the Cooking contents and all issues related to them are reserved by Practical Pictures.
N
Children
❑
Story/Song/Play:
songs and plays with the Boowa and Kwala characters.
The copyrights of the Children contents and issues related to them are reserved by UpToTen.
N
Fitness
❑
Basic Stretches/Massage:
that can be enjoyed by the whole family.
This is benecial health management content that provides stretching and massage exercises that can be enjoyed by the
N
whole family. The Basic Stretches contents for the Samsung TV are based on the book Stretching by Suzanne Martin
which is published by DK and the Massage contents are based on the books published by Anness Publishing.
The copyrights to Basic Stretches are reserved by the DK Publishing Company. The copyrights to the Massage content
N
are reserved by Practical Pictures. All issues related to copyrights are reserved by the corresponding company.
This function plays a Slide Show with high resolution images and background music and produces
You can view various recipes that you can then easily follow step by step. Enjoy these
This is educational and interactive content that children can watch repeatedly. Enjoy existing stories,
This is benecial health management content that provides stretching and massage exercises
Using the Remote Control Button in Fitness menu
ButtonOperations
◄/►
(Wheel)
E
ENTER
Screen Saver Run Time
❑
Select to set the waiting time before the screen saver appears.
Press the yellow button to select Setup in the Content Library main menu.
View to previous step/View to next step
Play or pause (in Basic and Advanced Stretches)
Page 52
Using Additional Content Using External USB Memory Storage
You can download contents onto a USB memory device and play them on your TV. (The contents on the external USB device are
played directly without being copied to the built-in Flash memory of the TV.)
Playing and Exiting New Content
1. Press the Red button in the Content Library main menu.
The USB Browser main screen is displayed.
N
A list of les saved on the USB device is displayed.
N
2. Press the ▲ or ▼ button to move to the le (or folder) you want to play. Press the ENTER
N
N
N
N
E
button.
The selected content is played.
The use of contents is the same as in using the TV memory contents.
To return to the USB browser main screen, press the EXIT button.
To exit Content Library mode, press the P>/< button on the remote
control.
Content Library only supports USB Mass Storage Class devices
N
(MSC). MSC is a Mass Storage Class Bulk-Only Transport device.
Examples of MSC are Thumb drives and Flash Card Readers (Both
USB HDD and HUB are not supported.)
Downloading New Contents
New content other than the built-in contents will be provided via the Samsung.com website with or without charge.
Downloading Content
1. Visit the www.samsung.com website and open the Content Library page.
2. Enter the product number (UDN, Unique Device Number) when it is asked.
3. Select a content item in the Contents Download page.
4. Download the contents onto the USB memory device.
Content Library only supports USB Mass Storage Class devices (MSC). MSC is a Mass Storage Class Bulk-Only
N
Transport device. Examples of MSC are Thumb drives and Flash Card Readers (Both USB HDD and HUB are not
supported.)
5. Go to Content Library main menu by pressing CONTENT button or choosing Content Library (Menu → Application →
Content Library)
6. Plug the USB memory into USB port on the side of the TV.
Finding a product number (Unique Device Number, UDN)
1. Insert the USB memory into the USB port on the side of the TV.
2. In the USB Browser main screen, press the Green button (Show UDN).
3. The 18-digit number on the screen is the product code.
Provided Content
Additional contents are available on www.samsung.com.
-
Content Library
Gallery
Content Library
Children
Sub Item : 2
Gallery
CookingChildrenFitness
Setup
USB
Return
USB
Children
Cooking
Fitness
Gallery
Living
Others
TV Memory
Show UDN
Exit
<<
▼ ▲
Return
1/1 >>
English - 52
Page 53
About Anynet
+
Connecting Anynet+ Devices
Anynet+ is a function that enables you to control all connected Samsung devices that support Anynet+ with your Samsung TV’s
remote.
The Anynet+ system can be used only with Samsung devices that have the Anynet+ feature. To be sure your Samsung device has
this feature, check if there is an Anynet+ logo on it.
To connect to a TV
TV
Anynet+
Device 1
Anynet+
Device 2
Anynet+
Device 3
Anynet+
Device 4
HDMI 1.3 Cable
HDMI 1.3 Cable
HDMI 1.3 Cable
HDMI 1.3 Cable
1. Connect the [HDMI 1], [HDMI 2], [HDMI 3] or [HDMI 4] jack on the TV and the HDMI OUT jack of the corresponding Anynet+
device using an HDMI cable.
To connect to Home Theater
TV
Home Theatre
Optical Cable
HDMI 1.3 Cable
Anynet+ Device 2Anynet+ Device 3
HDMI 1.3 Cable
HDMI 1.3 Cable
HDMI 1.3 Cable
1. Connect the [HDMI 1], [HDMI 2], [HDMI 3] or [HDMI 4] jack on the TV and the HDMI OUT jack of the corresponding Anynet+
device using an HDMI cable.
2. Connect the HDMI IN jack of the home theater and the HDMI OUT jack of the corresponding Anynet+ device using an HDMI
cable.
Connect the Optical cable between the Digital Audio Out (Optical) jack on your TV and the Digital Audio Input on the Home
N
Theater.
When following the connection above, the Optical jack only outputs 2 channel audio.
N
Theater’s Front Left and Right speakers and the subwoofer. If you want to hear 5.1 channel audio, connect the Digital Audio
Out (Optical) jack on the DVD player or Cable/Satellite Box (ie Anynet Device 1 or 2) directly to the Ampli er or Home Theater,
not the TV.
N
Connect only one Home Theater.
N
You can connect an Anynet+ device using the HDMI 1.3 cable. Some HDMI cables may not support Anynet+ functions.
N
Anynet+ works when the AV device supporting Anynet+ is in the Standby or On status.
N
Anynet+ supports up to 12 AV devices in total. Note that you can connect up to 3 devices of the same type.
Anynet+ Device 1
HDMI 1.3 Cable
Anynet+ Device 4
You will only hear sound from the Home
English - 53
Page 54
Setting Up Anynet+
Anynet+(HDMI-CEC)
❑
Tools→Anynet+(HDMI-CEC) performs the same function.
Setup
Anynet+(HDMI-CEC)
•
(HDMI-CEC) must be set to On.
N
When the Anynet+ (HDMI-CEC) function is disabled, all the Anynet+
related operations are deactivated.
•
TurnOff→No/Yes: Setting an Anynet+ Device to turn Off
Auto
Automatically when the TV is Turned Off
N
The active source on the TV remote must be set to TV to use the
Anynet+ function.
N
If you set Auto Turn Off to Yes, connected external devices are also
turned off when the TV is turned off. If an external device is still recording,
it may or may not turn off.
→Off/On
: To use the Anynet+ Function, Anynet+
Application
WISELINK Pro
Anynet+(HDMI-CEC)►
Content Library
Product Guide
Device List
Setup
U
Move E Enter R Return
Set up
Anynet+ (HDMI-CEC) : ON
Auto Turn Off : Yes
U
Move E Enter R Return
Off
On
Scanning and Switching between Anynet+ Devices
1. Press the TOOLS button. Press the ENTERE button to select Anynet+
(HDMI-CEC).
2. Press the ▲ or ▼ button to select Device List, then press the ENTER
E
button.
Anynet+ devices connected to the TV are listed. If you cannot nd a device
N
you want, press the red button to scan for devices.
Only when you set Anynet+ (HDMI-CEC) to On in the Setup menu, the
N
Device List menu appears.
3.
Press the ▲ or ▼ button to select to a particular device and press the
N
N
N
N
E
ENTER
button. It is switched to the selected device.
Switching to the selected devices may take up to 2 minutes. You cannot cancel the operation during the switching operation.
The time required to scan for devices is determined by the number of connected devices.
When the device scan is complete, the number of devices found are not displayed.
Although the TV automatically searches the device list when the TV is turned on via the power button, devices connected to
the TV when the TV is on or under some conditions are not automatically displayed in the device list. Press the red button to
search for the connected device.
If you have selected external input mode by pressing the SOURCE button, you cannot use the Anynet+ function. Make sure to
N
switch to an Anynet+ device by using the Device List.
View TV
Device List
Recording
: DVDR
DVDR Operation
Receiver :
Setup
On
U
Move E Enter R Return
English - 54
Page 55
English - 55
Anynet+ Menu
The Anynet+ menu changes depending on the type and status of the Anynet+ devices connected to the TV.
Anynet+ MenuDescription
View TVAnynet+ mode changes to TV broadcast mode.
Device ListShows the Anynet+ device list.
(device_name) MenuShows the connected device menus. E.g. If a DVD recorder is connected, the disc menu of
the DVD recorder will appear.
(device_name) OperationShows the play menu of the connected device. E.g. If a DVD recorder is connected, the play
menu of the DVD recorder will appear.
Record: (*recorder)Starts recording immediately using the recorder. (This is only available for devices that
support the recording function.)
(*recorder) Reserve RecordingEnables reserving a recording for the recorder. (This is only available for devices that support
the recording reservation function.)
Stop Recording: (*recorder)Stops recording.
ReceiverSound is played through the receiver.
N
If more than one recording device is connected, they are displayed as (*recorder) and if only one recording device is
connected, it will be represented as (*device_name).
TV Remote Control Buttons Available in Anynet+ Mode
Device TypeOperating StatusAvailable Buttons
After switching to the device, when
the menu of the corresponding
Anynet+ Device
device is displayed on the screen.
After switching to the device, while
playing a le
Device with builtin Tuner
After switching to the device, when
you are watching a TV programme
Audio DeviceWhen Receiver is activated
The Anynet+ function only works when the active source on the TV remote control is set to TV.
N
The
N
∏
button works only while in the recordable state.
N
You cannot control Anynet+ devices using the buttons on the TV. You can control Anynet+ devices only using the TV remote
control.
N
The TV remote control may not work under certain conditions. In this case, reselect the Anynet+ device.
N
The Anynet+ functions do not operate with other manufacturers’ products.
You can make a recording of a TV programme using a Samsung recorder.
Press the TOOLS button. Press the ENTER
1.
(HDMI-CEC).
2. Press the ▲ or ▼ button to select Recording: (device_name), then press the
E
ENTER
N
button. Recording begins.
When there is more than one recording device
When multiple recording devices are connected, the recording devices are
listed. Press the ▲ or ▼ button to select a recording device and press the
E
ENTER
N
When the recording device is not displayed
button. Recording begins.
Select Device List and press the red button to search devices.
3. Press the EXIT button to exit.
N
You can record the source streams by selecting Recording: (device_name).
N
Pressing the
∏
button will record whatever you are currently watching. If you are watching video from another device, the video
from the device is recorded.
N
Before recording, check whether the antenna jack is properly connected to the recording device.
antenna to a recording device, refer to the recording device’s users manual.
E
button to select Anynet+
View TV
Device List
Recording
DVDR Operation
Receiver :
Setup
: DVDR
On
U
Move E Enter R Return
To properly connect an
Page 56
Listening through a Receiver (Home theater)
You can listen to sound through a receiver instead of the TV speaker.
1.
Press the TOOLS button. Press the ENTER
(HDMI-CEC).
2. Press the ▲ or ▼ button to select Receiver. Press the ◄ or ► button to select
On or Off.
3.
Press the EXIT button to exit.
If your receiver supports audio only, it may not appear in the device list.
N
The receiver will work when you have properly connected the Optical IN jack of
N
E
button to select Anynet+
View TV
Device List
Recording
: DVDR
DVDR Operation
Receiver ◄
Setup
U
On ►
Move L Adjust R Return
the receiver to the Optical Out jack of the TV.
When the receiver (home theater) is set to On, you can hear sound output from the
N
TV’s Optical jack. When the TV is
displaying a DTV(air) signal, the TV will send out 5.1 channel sound to the Home theater receiver. When the source is a digital
component such as a DVD and is connected to the TV via HDMI, only 2 channel sound will be heard from the Home Theater
receiver.
N
When using the WISELINK Pro feature, sound may not output properly through the receiver
N
When listening through the receiver, there are restrictions for using the PIP and audio-related (MTS, Preferred language)
.
menus.
N
If there is a power interruption to the TV when the Receiver is set to On (by disconnecting the power cord or a power failure),
the Select Speaker may be set to External Speaker when you turn the TV on again. (see page 22)
Troubleshooting for Anynet+
SymptomSolution
Anynet+ does not work.Check if the device is an Anynet+ device. The Anynet+ system supports Anynet+ devices only.
I want to start Anynet+.Check if the Anynet+ device is properly connected to the TV and check if the Anynet+ (HDMI-
I want to exit Anynet+.Select View TV in the Anynet+ menu.
The message Connecting
to Anynet+ device...
appears on the screen.
The Anynet+ device does
not play.
The connected device is
not displayed.
The TV programme cannot
be recorded.
The TV sound is not output
through the receiver.
•
•
Connect only one receiver (home theater).
•
Check if the Anynet+ device power cord is properly connected.
•
Check the Anynet+ device’s Video/Audio/HDMI 1.3 cable connections.
•
Check whether Anynet+ (HDMI-CEC) is set to On in the Anynet+ setup menu.
•
Check whether the TV remote control is in TV mode.
•
Check whether it is Anynet+ exclusive remote control.
•
Anynet+ doesn’t work in certain situations. (Searching channels, Operating WISELINK Pro, Plug
& Play, etc.)
•
When connecting or removing the HDMI 1.3 cable, please make sure to search devices again or
turn your TV off and on again.
•
Check if the Anynet+ Function of Anynet+ device is set on.
•
CEC) is set to On in the Anynet+ Setup menu.
Press the TV button on the TV remote control to switch to TV. Then press the TOOLS button to
•
show the Anynet+ menu and select a menu you want.
•
Press the SOURCE button on the TV remote control and select a device other than Anynet+
•
devices.
>/<
Press P
•
(Note that the channel button operates only when a tuner-embedded Anynet+ device is not
•
and PRE-CH to change the TV mode.
connected.)
You cannot use the remote control when you are conguring Anynet+ or switching to a view
•
mode.
Use the remote control when the Anynet+ setting or switching to view mode is complete.
•
You cannot use the play function when Plug & Play is in progress.
Check whether or not the device supports Anynet+ functions.
•
Check whether or not the HDMI 1.3 cable is properly connected.
•
Check whether Anynet+ (HDMI-CEC) is set to On in the Anynet+ setup menu.
•
Search Anynet+ devices again.
•
You can connect an Anynet+ device using the HDMI 1.3 cable only. Some HDMI cables may not
•
support Anynet+ functions.
If it is terminated by an abnormal situation such as disconnecting the HDMI cable or power cord
•
or a power failure, please repeat the device scan.
Check whether the antenna jack on the recording device is properly connected.
Connect the optical cable between TV and the receiver.
English - 56
Page 57
English - 57
Recommendations for Use
Teletext Feature
Most television stations provide written information services via Teletext. The index page of the teletext service gives you
information on how to use the service. In addition, you can select various options to suit your requirements by using the remote
control buttons.
For teletext information to be displayed correctly, channel reception must be stable. Otherwise, information may be missing or
N
some pages may not be displayed.
1
: (exit)
Exit from the teletext display.
2
6 (index)
Used to display the index (contents) page at any time while you are viewing
teletext.
3
8 (store)
Used to store the teletext pages.
4
4 (size)
Press to display the double-size letters in the upper half of the screen. For lower
half of the screen, press it again. To display normal screen, press it once again.
5
5 (reveal)
Used to display the hidden text (answers to quiz games, for example). To display
normal screen, press it again.
6
/ (teletext on/mix)
Press to activate teletext mode after selecting the channel providing the teletext
service. Press it twice to overlap the teletext with the current broadcasting screen.
7
1 (sub-page)
Used to display the available sub-page.
8
2 (page up)
Used to display the next teletext page.
9
3 (page down)
Used to display the previous teletext page.
0
0 (mode)
Press to select the teletext mode (LIST/FLOF). If you press it in the LIST mode,
it switches into the List save mode. In the List save mode, you can save teletext
page into list using the 8(store) button.
!
9 (hold)
Used to hold the display on a given page if the selected page is linked with several
secondary pages which follow on automatically. To resume, press it again.
@
7 (cancel)
Used to display the broadcast when searching for a page.
#
Colour buttons (red/green/yellow/blue)
If the FASTEXT system is used by a broadcasting company, the different topics
covered on a teletext page are colour-coded and can be selected by pressing the
coloured buttons. Press one of them corresponding to the required. The page is
displayed with other coloured information that can be selected in the same way. To
display the previous or next page, press the corresponding coloured button.
You can change teletext pages by pressing the numeric buttons on the remote
N
control.
1
2
3
4
5
6
7
8
9
0
!
@
#
Page 58
The teletext pages are organized according to six categories:
PartContents
ASelected page number.
BBroadcasting channel identity.
CCurrent page number or search indications.
DDate and time.
EText.
FStatus information.
FASTEXT information.
N
Teletext information is often divided between several pages displayed in sequence,
which can be accessed by:
-
Entering the page number
-
Selecting a title in a list
-
Selecting a coloured heading (FASTEXT system)
Press the TV button to exit from the teletext display.
O
WallMountKitSpecications(VESA)
Install your wall mount on a solid wall perpendicular to the oor.
When attaching to other building materials, please contact your nearest dealer.
If installed on a ceiling or slanted wall, it may fall and result in severe personal injury.
Product FamilyinchVESA Spec. (A * B)
23 ~ 26200 * 100M4
32 ~ 40200 * 200M6
LCD-TV
PDP-TV
We provided the standard dimensions for wall mount kits as shown in the table above.
N
When purchasing our wall mount kit, a detailed installation manual and all parts necessary for assembly are provided.
N
Do not use screws longer than the standard dimension, as they may cause damage to the inside of the TV set.
N
For wall mounts that do not comply with the VESA standard screw specifications, the length of the screws may differ
N
depending on their specifications.
Do not use screws that do not comply with the VESA standard screw specifications.
N
Do not use fasten the screws too strongly, this may damage the product or cause the product to fall, leading to personal injury.
Samsung is not liable for these kinds of accidents.
Samsung is not liable for product damage or personal injury when a non-VESA or non-specified wall mount is used or the
N
consumer fails to follow the product installation instructions.
Our 57” and 63” models do not comply with VESA Specifications. Therefore, you should use our dedicated wall mount kit for
N
this model.
Do not exceed 15 degrees tilt when mounting this TV.
N
Do not install your Wall Mount Kit while your TV is turned on.
It may result in personal injury due to electric shock.
46 ~ 52
57
57 ~ 70800 * 400
80 ~1400 * 800
42 ~ 58
63
63 ~ 70800 * 4004
80 ~1400 * 8004
400 * 400
600 * 400
700 * 400
(No VESA)
400 * 400
600 * 400
676 * 407
(No VESA)
Standard
Screw
M8
M8
Quantity
4
4
6
English - 58
Page 59
English - 59
Auto Wall-Mount Adjustment (Sold separately) (Depending on the model)
Once the auto wall mount is installed, your TV’s position can be easily adjusted.
Rear Panel
Serial Cable(1P to 1P)(Not supplied)
Entering the menu
1. Press the ▲, ▼, ◄ or ► button on your remote control.
The Wall Mount Adjustment screen is displayed.
N
If the Auto Wall-Mount screen is not displayed when clicking on a direction
N
button while watching your TV, use the menu to display that screen.
Press the MENU button to display the menu. Press the ▲ or ▼ button to
-
select Setup, then press the ENTER
-
Press the ▲ or ▼ button to select Wall-Mount Adjustment, then press
the ENTER
E
button.
E
button.
Remembering the Position
2. Adjust to the desired position using the ▲,▼,◄,► buttons.
N
If you press an arrow button when no OSD is displayed on the TV screen,
the Adjustment screen appears.
N
Press the INFO button to reset. Press the ◄ or ► button to select Yes,
then press the ENTER
setting.
3. Press the blue button. Press the ▲ and ▼ buttons to select a save mode from
either Position 1, Position 2 or Position 3 in order to save the current position.
N
To not save the current position, press the RETURN button.
When selecting a save mode, you cannot use the Colour buttons.
O
4.
Press the ENTER
When Position1 is selected, the message Current position saved as Position1 is displayed.
N
5.
Press the ENTER
The saved Position appears on the left side of the OSD.
N
E
E
button to save.
E
button.
button. The position is initialized to the default
Auto Wall-Mount
Digital Text : Enable
Light Effect : Watching TV
Setup
Wall-Mount Adjustment
Melody : Off
Entertainment : Off
Energy Saving : Off
PIP
Software Upgrade
Common Interface
Wall-Mount Adjustment
Position 1 2 3
►
Adjust Save Centre
Moving to the remembered position
1. Complete Step 1 of Entering the menu.
2. Pressing a Colour (Red, Green, Yellow) button moves the auto wall mount to the
saved position.
N
You can move the wall mount to one of the 3 pre-set positions by pressing
the Red (Position 1), Green (Position 2) or Yellow (Position 3) buttons.
N
If you adjust the Position after moving to a pre-set position, the position
Save
Select a mode to save.
Position1
Position2
Position3
Move Enter Return
display will disappear.
N
For installation, refer to the Installation Manual provided with the wall mount.
N
For product installation and the installation and moving of the wall mount, make sure to consult a specialized installation
company.
N
This installation manual is to be used when attaching the wall mount to a wall. When attaching to other building materials,
please contact your nearest dealer.
N
The auto wall mount will not work when Anynet+ or WISELINK Pro is operating.
Page 60
Preparing before installing Wall- Mount on the wall
주의
Case A. Installing SAMSUNG Wall-MountCase B. Installing other company’s Wall-Mount
1. Install Wall Mount with the torque range of 15kgf·cm or less. Make sure that parts can be damaged if the torque is out of the
specied range.
2. Accessory Kit contains Holder–Ring [①] for installing other company’s Wall-Mount on Samsung TV. (Case B)
Securing the TV to the Wall
Pulling, pushing, or climbing on the TV may cause the TV to fall. In particular, ensure your children do not hang
over or destabilize the TV; doing so may cause the TV to tip over, causing serious injuries or death. Follow all
safety precautions provided on the included Safety Flyer. For added stability, install the anti-fall device for safety
purposes, as follows.
Wall
Wall
To avoid the TV from falling:
1. Put the screws into the clamps and rmly fasten them onto the wall. Conrm that the screws have been rmly installed onto
the wall.
You may need additional material such as an anchor depending on the type of wall.
N
Since the necessary clamps, screws, and string are not supplied, please purchase these additionally.
N
2
. Remove the screws from the center back of the TV, put the screws into the clamps, and then fasten the screws onto the TV
again.
N
Screws may not be supplied with the product. In this case, please purchase the screws of the following specifications.
Connect the clamps xed onto the TV and the clamps xed onto the wall with a strong string and then tie the string tightly.
3.
N
Install the TV near to the wall so that it does not fall backwards
N
It is safe to connect the string so that the clamps fixed on the wall are equal to or lower than the clamps fixed on the TV.
N
Untie the string before moving the TV.
4.
Verify all connections are properly secured. Periodically check connections for any sign of fatigue for failure. If you have any
doubt about the security of your connections,contact a professional installer.
.
English - 60
Page 61
English - 61
Troubleshooting
Before contacting the Samsung after-sales service, perform the following simple checks.
If you cannot solve the problem using the instructions below, note the model and serial number of the television and contact your
local dealer.
No sound or pictureCheck that the mains lead has been connected to a wall socket.
Normal picture but no soundCheck the volume.
No picture or black and white
picture
Sound and picture interferenceTry to identify the electrical appliance that is affecting the television, then move it further
Blurred or snowy picture,
distorted sound
Remote control malfunctionsReplace the remote control batteries.
Screen is black and power
indicator light blinks steadily
The damaged picture appears in
the corner of the screen.
The "Resets all settings to
the default values" message
appears.
•
Check that you have pressed the button on your set.
•
Check the picture contrast and brightness settings.
•
Check the volume.
•
Check if Select Speaker is set to External Speaker.
•
•
Check whether the MUTEM button has been pressed on the remote control.
•
Adjust the colour settings.
•
Check that the broadcast system selected is correct.
•
•
away.
Plug the television into a different main socket.
•
Check the direction, location and connections of your aerial.
•
This interference often occurs due to the use of an indoor aerial.
•
•
Clean the upper edge of the remote control (transmission window).
•
Check that the + and – ends of the batteries are inserted correctly.
•
Check that the batteries are drained.
•
On your computer check; Power, Signal Cable.
•
The TV is using its power management system.
•
Move the computer’s mouse or press any key on the keyboard.
•
On your equipment check (STB, DVD, etc) ; Power, Signal Cable.
•
The TV is using its power management system.
•
Press the Source button on the panel or remote control.
•
Turn the TV off and on.
•
If Just Scan is selected in some external devices, the damaged picture may appear in the
•
corner of the screen. This symptom is caused by external devices, not TV.
This appears when you press and hold the EXIT button for a while. The product settings
•
are reset to the factory defaults.
Page 62
Specications
The descriptions and characteristics in this booklet are given for information purposes only and are subject to modification without
notice.
Model NamePS50A756 PS63A756
Screen Size (Diagonal)
PC Resolution (Optimum)
Sound (Output) 10 W x 215 W x 2
Dimension (WxHxD)
Body
With stand
Weight
Body
With stand
Environmental Considerations
Operating Temperature
Operating Humidity
Storage Temperature
Storage Humidity
This device is a Class B digital apparatus.
N
Design and specications are subject to change without prior notice.
N
For the power supply and Power Consumption, refer to the label attached to the product.
N
50 inch63 inch
1920 x 1080 @ 60 Hz1920 x 1080 @ 60 Hz
1240 x 766 x 96 mm
1240 x 830 x 315 mm
39 kg
44 kg
50 °F to 104 °F (10 °C to 40 °C)
10% to 80%, non-condensing
-4 °F to 113 °F (-20 °C to 45 °C)
5% to 95%, non-condensing
1531 x 932 x 99 mm
1531 x 1005 x 418 mm
67 kg
84 kg
English - 62
Page 63
This page is intentionally
left blank.
Page 64
Correct Disposal of This Product
(Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with
separate collection systems)
This marking shown on the product or its literature, indicates that it
should not be disposed with other household wastes at the end of its
working life.
To prevent possible harm to the environment or human health from
uncontrolled waste disposal, please separate this from other types of
wastes and recycle it responsibly to promote the sustainable reuse of
material resources.
Household users should contact either the retailer where they
purchased this product, or their local government office, for details
of where and how they can take this item for environmentally safe
recycling.
Business users should contact their supplier and check the terms and
conditions of the purchase contract. This product should not be mixed
with other commercial wastes for disposal.
Page 65
Français - 2
Instructions d’utilisation
Rémanence à l’écran
Ne figez pas d’images (telle qu’une image de jeu vidéo ou de PC branché à l’écran à plasma) sur l’écran du moniteur à
plasma pendant plus de deux heures car cela peut entraîner une rémanence à l’écran. Cette rémanence est également
appelée “brûlure d’écran”. Pour éviter la rémanence, réduisez le niveau de contraste ou de luminosité de l’écran lorsque vous
affichez une image figée.
Hauteur
L
’écran à plasma est normalement conçu pour être utilisé à une altitude inférieure à 2000 m. Il peut fonctionner de façon
anormale au-dessus de 2000 m d’altitude. Ne l’installez pas et ne le faites donc pas fonctionner dans ces conditions.
Chaleur diffusée sur la partie supérieure du téléviseur à plasma
Le dessus de l’appareil peut chauffer en cas d’utilisation prolongée, car la chaleur s’échappe du panneau par le trou d’
aération situé dans la partie supérieure du produit. Ce phénomène est normal et n’indique aucunement la présence d’un
défaut ou d’un dysfonctionnement. Il convient cependant d’empêcher les enfants de toucher à la partie supérieure de l’écran.
Le produit fait un bruit de “claquement”.
Ce bruit de “claquement” risque d’être perceptible lorsque le produit se contracte ou s’étend suite à un changement du milieu
ambiant, tel que la température ou l’humidité. Ce phénomène est normal et ne constitue pas un défaut.
Défauts de cellule
L
’écran à plasma utilise un panneau constitué de 1 230 000 (niveau SD) à 3 150 000 (niveau HD) pixels dont la fabrication
fait appel à une technologie avancée. Il se peut toutefois que des points clairs ou sombres apparaissent à l’écran. Ils n’ont
aucune incidence sur la performance du produit.
Evitez d’utiliser le téléviseur à plasma à des températures inférieures à 5°C (41°F).
Une image figée affichée pendant une période prolongée peut endommager définitivement l’écran PDP.Visionner
pendant longtemps le téléviseur à plasma en format 4/3 risque de laisser apparaître des traces de
bordures sur la gauche, sur la droite et au centre de l’écran. Ces traces sont dues à la différence de
luminosité sur l’écran. Lire un DVD ou un jeu vidéo sur console risque de provoquer un effet similaire sur
l’écran. Les dommages provoqués par l’effet susmentionné ne sont pas couverts par la garantie.
Rémanence de l’image à l’écran.
Une rémanence partielle de l’image peut éventuellement se produire si des images figées de jeux vidéo et d’un PC restent
affichées pendant un certain temps. Pour empêcher ce phénomène, réduisez la luminosité et le contraste en cas d’affichage
d’images figées.
Garantie
- La garantie ne couvre pas les dommages causés par la rémanence.
- Les brûlures ne sont pas couvertes par la garantie.
Installation
Contacter un centre de service agréé si le téléviseur est destiné à une installation dans des endroits exposés à la poussière,
à des températures faibles ou élevées, à une forte humidité, à des substances chimiques et s’il a été prévu pour fonctionner
en permanence, comme dans des aéroports, des gares ferroviaires, etc. Le non-respect de ce qui précède peut gravement
endommager le téléviseur.
Avertissement concernant les téléviseurs numériques (DVB-T)
1. LES FONCTIONS RELATIVES À LA TÉLÉVISION NUMÉRIQUE (DVB) NE SONT DISPONIBLES QUE DANS LES
PAYS OU RÉGIONS OÙ DES SIGNAUX TERRESTRES NUMÉRIQUES DE TYPE DVB-T (MPEG2 er MPEG4 AVC)
SONT DIFFUSÉS. DVB-T est le standard du consortium européen pour la diffusion de signaux terrestres de télévision
numérique. Consultez votre distributeur local pour savoir si des services DVB-T sont disponibles dans votre région.
2. Bien que ce téléviseur soit conforme à la norme DVB-T (août 2008), il n’est pas garanti qu’il soit compatible avec les
futures émissions terrestres numériques DVB-T.
3. Il se peut que certaines fonctions de
TV numérique ne soient pas disponibles ou ne fonctionnent pas correctement dans
certains pays ou certaines régions.
4. Pour plus d’informations, contactez votre service client de SAMSUNG.
Comment contacter Samsung dans le monde
Si vous avez des suggestions ou des questions concernant les produits Samsung, veuillez contacter le Service
Consommateurs Samsung.(Voir la quatrième de couverture pour plus d’informations.)
Assemblage de la base-support (en fonction du modèle)
Au moyen des 6 vis permettant de solidariser la base-support et le TV,
fixez fermement le TV à la base-support.
(L’aspect extérieur de votre téléviseur peut différer de celui présenté à l’
image.)
Si vous fixez le téléviseur au mur, Refermez le
couvercle (1) de la pièce de connexion de la basesupport à l’aide des deux vis.
Avertissement
Fixez fermement le socle au téléviseur
avant de déplacer ce dernier. Il pourrait
tomber et provoquer de graves dommages.
Le téléviseur doit être soulevé par
plusieurs personnes. Ne posez jamais
le téléviseur sur le sol car cela pourrait
l’endommager.
Conservez toujours le téléviseur en
position verticale.
N
Vérification des pièces
Manuel d'utilisationTélécommande/Piles AAACordon d'alimentation
Chiffon de nettoyage
Carte de garantie/ Manuel
de sécurité (Non disponible
dans tous les pays)
Capot inférieur / Vis (2ea)
(PS50A756)
Anneau de support (4ea)
(reportez-vous à la page 60)
CD du programme
Tore magnétique pour
cordon d’alimentation
(2ea)
Utilisation de la base-support
L’écran à plasma doit être soulevé par plusieurs personnes. Ne posez
jamais l’écran à plasma sur le sol, car cela pourrait l’endommager.
Conservez toujours l’écran en position verticale.
Le PDP peut pivoter de 20 degrés vers la droite et la gauche.
N
N
Branchement et installation de votre téléviseur
-20° ~ 20°
Tore magnétique (Cordon d'alimentation)
Le blindage magnétique sert à protéger les câbles des interférences. Lors de la connexion d’un
câble, ouvrez le blindage magnétique et rabattez-le autour du câble près de la prise.
N
Page 68
Français - 5
Présentation du panneau de commande
La couleur et la forme du produit peuvent varier en fonction du modèle.
N
Boutons en façade
Touchez les boutons
pour les actionner.
1
SOURCE
E
Permet de basculer entre les sources d'entrée disponibles
Dans le menu à l'écran, ce bouton a la même fonction
que le bouton ENTER de la télécommande.
2
MENU
Permet d’afcher le menu des fonctions de votre téléviseur
sur l’écran.
3
– = +
Appuyez pour augmenter ou réduire le volume. Dans le
menu afché à l’écran, utilisez les boutons
– = +
de la
même façon que les boutons ◄ et ► de la télécommande.
4
< C/P.P
>
Permet de changer de canal. Dans le menu afché à l’
écran, utilisez les boutons < C/P.P > de la même
façon que les boutons ▲ et ▼ de la télécommande.
5
TÉMOIN D’ALIMENTATION
Clignote et s’éteint lorsqu’il est sous tension et
s’allume en mode Veille.
6
CAPTEUR DE LA TÉLÉCOMMANDE
Dirigez la télécommande vers ce point du téléviseur.
N
7
HAUT-PARLEUR
8
P (POWER)
Touchez le capteur argenté sous la marque (P) pour
mettre le téléviseur sous et hors tension.
Capteur argenté
Page 69
Français - 6
Présentation du panneau de branchement
En cas de branchement d’un système audio ou vidéo sur le téléviseur, vérifiez que tous les appareils sont éteints.
Lorsque vous branchez un périphérique externe, faites correspondre les couleurs de la borne de connexion et du câble.
N
N
Panneau arrière
Télévision câblée
Réseau
ou
ou
ou
1
5796
0
834
La couleur et la forme du produit peuvent varier en fonction du modèle.
N
1
ENTREE ALIMENTATION
Permet de raccorder le cordon d’alimentation fourni.
2
COMPONENT IN
Entrées audio (AUDIO G/D) et vidéo (Y/P
B/PR) pour
Composant.
3
LAN
Connectez un câble réseau à ce port pour connecter le
téléviseur au réseau.
4
PC IN (PC) / AUDIO
Pour raccorder la prise de sortie vidéo et audio de votre
PC.
5
EXT 1, EXT 2
Entrées ou sorties pour périphériques tels que des
magnétoscopes, des lecteurs DVD, des consoles de jeux
vidéo ou des lecteurs de vidéodisques.
Spécifications entrée/sortie
Connecteur
EntréeSortie
V
idéo Audio (G/D) RGBVidéo + Audio (G/D)
EXT 1
✔✔✔
Seule la sortie TV ou
DTV est disponible.
EXT 2
✔✔
Sortie que vous pouvez
sélectionner.
6
DIGITAL AUDIO OUT (OPTICAL)
A connecter à un composant audio numérique.
7
AUDIO OUT(AUDIO R/L)
Connectez les signales audio RCA de la TV à une
source externe, telle qu’un équipement audio.
8
SERVICE
− Prise pour tests.
9
HDMI IN 1,2,3
− Aucune connexion audio supplémentaire n’est
nécessaire pour une connexion HDMI - HDMI.
−
Lorsque vous utilisez une connexion avec câble HDMI/
DVI, vous devez utiliser la borne HDMI IN2.
Qu’est-ce que HDMI?
−
High Definition Multimedia interface permet la
transmission de données vidéo numériques haute
définition et plusieurs canaux de son numérique.
−
Le terminal HDMI/DVI prend en charge la connexion DVI
vers un périphérique raccordé avec le câble adéquat
(non fourni). La différence entre HDMI et DVI est que
le périphérique HDMI est plus petit, est équipé de la
fonction de codage HDCP (High Bandwidth Digital Copy
Protection), et gère le son numérique multicanal.
DVI IN (HDMI 2) AUDIO R/L
Sorties audio DVI pour périphériques externes.
0
ANT IN
Connecteur coaxial 75Ω pour réseau câblé/hertzien.
La couleur et la forme du produit peuvent varier en fonction du modèle.
N
Panneau latéral
ou
4
5
3
2
1
4
1
Logement pour COMMON INTERFACE
Insérez la carte d’interface commune dans ce logement.
(reportez-vous à la page
25)
− Si vous n’insérez pas la
carte d’int erface commune
dans certaines chaînes, Signal brouillé s’affiche sur l’
écran.
−
Les informations de pairage contenant un numéro de
téléphone, l’ID de la carte d’interface commune, l’ID de l’hôte
et d’autres informations s’afficheront dans les 2 ou 3 minutes.
Si un message d’erreur s’affiche, contactez votre prestataire
de service.
−
Lorsque la configuration des informations sur les canaux
est terminée, le message Mise à jour terminée s’affiche,
indiquant que la liste des canaux est dorénavant mise à
jour.
Insérez la carte d’interface commune dans le sens
indiqué sur celle-ci.
2
HDMI IN 4
A connecter à la prise HDMI d’un périphérique équipé d’une
sortie HDMI.
3
WISELINK PRO
Connectez un périphérique de stockage de masse USB pour
afficher des photos (JPEG) et écouter des fichiers audio
(MP3) et vidéo.
Vous pouvez vous connecter au réseau SAMSUNG sans fil.
4
S-VIDEO ou VIDEO / AUDIO L/R
Entrées audio et vidéo (S-Vidéo ou Vidéo) pour périphériques
externes, tels qu’un caméscope ou un magnétoscope.
N
5
PRISE CASQUE
Vous pouvez brancher un casque si vous souhaitez
regarder la télévision sans déranger les autres
personnes présentes dans la pièce.
L’utilisation prolongée d’un casque à un niveau
sonore élevé peut endommager l’ouïe.
N
Page 71
Français - 8
1
Bouton POWER
(permet d'allumer et d'éteindre le
téléviseur)
2
Permet de sélectionner directement
le mode TV.
3
Pavé numérique pour l'accès direct
aux chaînes
4
Sélection de chaînes à un ou
plusieurs chiffres
5
Suppression temporaire du son
6 Sélection de la source disponible
7
Augmentation du volume
Réduction du volume
8
Affichage EPG (Guide électronique
des programmes)
9
Permet de sélectionner rapidement
les fonctions fréquemment utilisées.
0
Permet de commander le curseur
dans le menu
!
Permet d'afficher les informations
relatives au programme en cours
@
Utilisez ces boutons dans la Liste
des chaînes, WISELINK Pro, etc.
$
Appuyez sur cette touche pour
sélectionner l'affichage et les modes
son en option pour le sport, le
cinéma et les jeux.
%
Utilisez ces boutons dans la liste des
chaînes, WISELINK Pro et Anynet+.
^
ON/OFF
Permet d'activer l'éclairage des
boutons de la télécommande.Cette
fonction est pratique la nuit ou
lorsqu'il fait sombre dans la pièce.
(Utiliser la télécommande avec le
bouton lumineux ON/OFF (
) réglé
sur Marche permet de réduire la
durée d'utilisation de la pile.)
&
Chaîne précédente
*
Chaîne suivante
Chaîne précédente
(
Permet d'afficher le menu principal à
l'écran
)
Cette fonction permet d'afficher des
photos (JPEG) et d'écouter des
fichiers audio (MP3) et vidéo à partir
d'un périphérique externe.
a
Permet de revenir au menu
précédent
b
Permet de quitter le menu affiché à
l'écran
c
Non disponible
d
Utilisez ce paramètre lorsque vous
connectez un appareil SAMSUNG
DMA
(Digital Media Adapter) via une
interface HDMI et basculez en
mode DMA. (Le bouton DMA est en
option.) Pour plus d’informations sur
les procédures de fonctionnement,
reportez-vous au manuel d’utilisation
de l’appareil DMA. Ce bouton est
disponible si la fonction Anynet+ (HDMI-CEC) est Marche (voir page
54).
e
Cette fonction vous permet d'afficher
Content Library.
f
Affichage numérique des sous-titres
Fonctions télétexte
2
Permet de quitter l'affichage télétexte
(en fonction du modèle)
6
Sélection du mode Télétexte (LIST/
FLOF)
8
émorisation du télétexte
9
Taille du télétexte
!
Activation du télétexte
@
Sélection des rubriques Fastext
#
Affichage télétexte/informations
relatives au télétexte et programme
normal
&
Page secondaire télétexte
*
P : page télétexte uivante
P
: page télétexte précédente
(
Index du télétexte
a
Pause télétexte
b
Annulation du télétexte
Télécommande
Vous pouvez utiliser la télécommande à une distance maximale du téléviseur d’environ 7 m.
Une lumière intense peut affecter le bon fonctionnement de la télécommande.
N
Page 72
Français - 9
Insertion des piles dans la télécommande
1. Soulevez le couvercle situé à l’arrière de la télécommande comme indiqué sur
la gure.
2. Placez deux piles AAA.
Assurez-vous de faire correspondre les bornes “+” et “-” des piles avec le
schéma situé à l’intérieur du compartiment.
3.
Refermez le couvercle comme indiqué sur la gure.
Retirez les piles et stockez-les dans un endroit frais et sec si vous n’utilisez
pas la télécommande pendant longtemps.
Utiliser la télécommande avec le bouton lumineux ON/OFF@ réglé sur
Marche permet de réduire la durée d'utilisation de la pile.
Si la télécommande ne fonctionne pas Vériez les éléments suivants :
1. Le téléviseur est-il sous tension?
2. Les bornes + et - des piles ne sont-elles pas inversées?
3. Les piles sont-elles déchargées ?
4. Le cordon d’alimentation est-il débranché ou y a-t-il une panne de courant?
5. Une lampe fluorescente ou néon est-elle allumée à proximité?
N
Mise en marche et arrêt
Le câble relié au secteur est xé à l'arrière du téléviseur/moniteur.
1.
Branchez le cordon d'alimentation sur une prise secteur appropriée.
Le voyant de veille s'allume sur le téléviseur.
2
. Appuyez sur le bouton POWER P de votre téléviseur.
Vous pouvez également appuyer sur le bouton POWER P ou sur le bouton TV de votre télécommande pour allumer le
téléviseur.
Le dernier programme que vous avez regardé est automatiquement re-sélectionné.
3.
Appuyez sur le bouton numérique (de 0 à 9) ou le bouton canal suivant/précédent (< / >) de la télécommande ou sur le
bouton >C/P.
P
< de votre téléviseur.
Lorsque vous allumez le téléviseur pour la première fois, vous devrez choisir la langue dans laquelle vous souhaitez que
les menus s'afchent.
4.
Pour éteindre votre téléviseur, appuyez de nouveau sur le bouton POWER
P
.
Mise en mode veille de votre téléviseur
Vous pouvez mettre votre téléviseur en mode Veille an de réduire la consommation électrique. Le mode veille peut être utile si
vous souhaitez éteindre votre téléviseur temporairement (pendant un repas par exemple).
1. Appuyez sur le bouton POWER
P
de la télécommande.
L'écran s'éteint et un voyant de veille rouge apparaît sur votre téléviseur.
2
. Pour rallumer le téléviseur, appuyez de nouveau sur le bouton POWER
P
, les boutons numériques (de 0 à 9), le bouton TV
ou les boutons canal suivant/précédent (< / >).
Ne laissez pas le téléviseur en mode Veille pendant de longues périodes (lorsque vous êtes en vacances par exemple). Il
est conseillé de débrancher le téléviseur du secteur et de l'antenne.
N
N
N
N
N
N
N
N
N
Page 73
Français - 10
Affichage des menus
1. Une fois l’appareil allumé, appuyez sur le bouton MENU. Le menu principal
apparaît à l'écran. Plusieurs icônes s’afchent sur le côté gauche du menu :
Image, Son, Chaîne, Conguration, Entrée, Application.
2. Appuyez sur le bouton ▲ ou ▼ pour sélectionner l'une des icônes. Appuyez
ensuite sur ENTER
E
pour accéder au sous-menu de l'icône.
3. Appuyez sur le bouton EXIT pour quitter le menu.
Les menus disparaissent de l'écran après environ une minute.
Utilisation du bouton TOOLS
Vous pouvez utiliser le bouton TOOLS pour sélectionner simplement et rapidement
les fonctions que vous utilisez le plus souvent. Le menu Outils change en fonction
du mode d'entrée externe afché.
1. Appuyez sur le bouton TOOLS. Le menu Outils s'afche.
2
. Appuyez sur le bouton ▲ ou ▼ pour sélectionner un menu.
3.
Appuyez sur les boutons ▲/▼/◄/►/ ENTER
E
pour afcher,changer ou
utiliser les éléments sélectionnés. Pour une description plus détaillée de chaque
fonction, reportez-vous à la page correspondante.
Pour passer à la chaîne suivante lorsque vous êtes en mode d'affichage des
chaînes, faites tourner la molette dans le sens des aiguilles d'une montre.
Pour passer à la chaîne précédente, faites tourner la molette dans le sens
inverse des aiguilles d'une montre.
Pour augmenter le volume lorsque la fenêtre de réglage du volume est
affichée, faites tourner la molette dans le sens des aiguilles d'une montre.
Pour baisser le volume, faites tourner la molette dans le sens inverse des
aiguilles d'une montre.
Pour sélectionner un sous-menu lorsque vous êtes en mode d'affichage des
menus, faites tourner la molette dans le sens des aiguilles d'une montre.
Pour remonter dans l'arborescence des menus, faites tourner la molette dans
le sens inverse des aiguilles d'une montre.
Anynet+ (HDMI-CEC)
Format de l'image : 16/9 auto
Mode Image : Standard
Mode Son : Personnel
Veille : Arrêt
SRS TS XT : Arrêt
Mode éco. : Arrêt
Dual l ll : Mono
U
Déplacer E Entrer e Quitter
Page 74
Français - 11
Fonction Plug & Play
Lorsque vous allumez le téléviseur pour la première fois, des réglages de base s’effectuent l’un après l’autre de manière
automatique.
1. Appuyez sur le bouton POWER de la télécommande. Le message The Menu
Language, Store Demo, Channels and Time will be set. s’afche.
2
. Appuyez sur le bouton ENTER
E
. Le menu Select the OSD Language.
s’afche automatiquement. Appuyez sur le bouton ENTER
E
.
3. Sélectionnez la langue appropriée en appuyant sur le bouton ▲ ou ▼. Appuyezsur le bouton ENTERE pour conrmer votre choix.
4. Appuyez sur le bouton ◄ ou ► pour sélectionner Enr. démo ou Util. domicile, puis appuyez sur le bouton ENTER
E
.
Nous recommandons de régler la télévision sur le mode Util. domicile pour une meilleure qualité d’image dans votre
environnement personnel. Le mode
Enr. démo n’est prévu que pour un usage en magasin.
Si l’unité est accidentellement réglée sur le mode Enr. démo et que vous souhaitez revenir au mode Util. domicile
(Standard): Appuyez sur le bouton Volume du téléviseur. Lorsque l’OSD du volume s’afche, appuyez pendant
5
secondes sur le bouton MENU du téléviseur.
L'écran de veille est activé si aucune touche de la télécommande n'est actionnée pendant plus d'une minute lorsque le
mode Plug & Play est en cours d'exécution.
L'écran de veille est activé si aucun signal de fonctionnement n'est reçu pendant plus de 15 minutes.
5. Appuyez sur le bouton ENTER
E
. Sélectionnez le pays approprié en appuyant sur le bouton ▲ ou ▼. Appuyez sur le bouton
ENTERE pour conrmer votre choix.
6. Appuyez sur le bouton ▲ ou ▼ pour sélectionner la source de chaîne à mémoriser. Appuyez sur le bouton ENTER
E
pour
sélectionner Démarrer.
Numérique et Analogique: Chaînes numériques et analogiques.
Numérique: Chaînes numériques.
Analogique: Chaînes analogiques.
La recherche de canaux démarrera et se terminera automatiquement.
Appuyez sur le bouton ENTER
E
à tout moment pour interrompre la mémorisation.
Une fois que tous les canaux disponibles sont mémorisés, le message Dénit le mode Horlogs. s’afche.
7
. Appuyez sur le bouton ENTER
E
. Appuyez sur le bouton ▲ ou ▼ pour sélectionner Auto., puis appuyez sur le bouton
ENTERE.
Si vous sélectionnez Manuel, le message Dénit la date et I'heure s’afche. (Reportez-vous à la page 26)
Si vous avez reçu un signal numérique, l’heure sera automatiquement réglée. Sinon, reportez-vous à la page 26 pour
régler l’horloge.
8
. Le message Protez de votre visionnage s’afche. Lorsque vous avez terminé, appuyez sur le bouton ENTER
E
.
Si vous souhaitez réinitialiser cette fonction...
1. Appuyez sur le bouton MENU pour afcher le menu. Appuyez sur le bouton ▲ ou ▼ pour sélectionner Conguration, puis appuyez sur le bouton ENTER
E
.
2. Appuyez de nouveau sur le bouton ENTER
E
pour sélectionner Plug & Play.
3. Entrez votre code PIN à quatre chif
fres. Le code PIN par défaut d’un nouveau
téléviseur est “0-0-0-0”.
Si vous souhaitez changer ce code PIN, reportez-vous à la page 23.
La fonction Plug & Play est uniquement disponible en mode TV.
N
N
N
N
N
N
N
N
N
N
N
N
N
Mémorisation des chaînes
Pays
Canal analogique: Permet de changer de pays pour les chaînes
analogiques.
Canal numérique: Permet de changer de pays
pour les chaînes
numériques.
L’écran de saisie du code PIN apparaît. Entrez votre code PIN à quatre chiffres.
❑
N
Gestion des canaux
Conguration
Plug & Play
►
Langue : Français
Horloge
Sélection du réseau : Câble
Configuration du réseau sans fil
Configuration internet
Verrouillage Canal : Marche
Modifier PIN
Canal
Pays
►
Mémorisation Auto
Mémorisation Manuelle
Guide Complet
Mini Guide
Par
défaut : Mini Guide
Liste des chaînes
Mode
Canal : Chaînes ajoutées
Plug & Play
The Menu Language, Store Demo, Channels and Time
will be set.
OK
E Entrer
Page 75
Français - 12
Mémorisation Auto
Vous pouvez chercher les plages de fréquence disponibles par balayage (leur disponibilité dépend de votre pays). Il est
possible que les numéros de programme attribués automatiquement ne correspondent pas aux numéros de programme
souhaités ou réels.
Numérique et Analogique: Chaînes numériques et analogiques.
Numérique: Chaînes numériques.
Analogique: Chaînes analogiques.
Cherche toutes les chaînes avec des stations de diffusion active et les enregistre dans la mémoire du téléviseur.
Si vous voulez arrêter la mémorisation automatique, appuyez sur le bouton ENTER
E
.
Le message Arrêter le programme automatique ? s’afche.
Sélectionnez Oui en appuyant sur le bouton ◄ ou ►, puis appuyez sur le bouton ENTER
E
.
Si une chaîne est verrouillée par la fonction Verrouillage Canal, la fenêtre de saisie du code PIN s’afche.
Mémorisation Manuelle
Permet de chercher manuellement une chaîne et de l’enregistrer dans la mémoire du téléviseur.
Si une chaîne est verrouillée par la fonction Verrouillage Canal, la fenêtre de saisie du code PIN s’afche.
Canal numérique
Enregistrement manuel de chaînes numériques.
Canal: Sélectionnez le numéro de chaîne à l’aide des boutons ▲, ▼ ou des chiffres (0-
9).
Fréquence: Sélectionnez la fréquence à l’aide des chiffres.
Bande passante: Sélectionnez la bande passante à l’aide des boutons ▲, ▼ ou des chiffres (0-
9).
Au terme de la recherche, les chaînes de la liste sont mises à jour.
Canal analogique
Enregistrement manuel de chaînes analogiques.
Programme (numéro de programme à attribuer à une chaîne): Sélectionnez le numéro de chaîne à l’aide des boutons
▲,▼ ou des chiffres (0-9).
Système de Couleur → Auto. / PAL / SECAM / NTSC4.43: Sélectionnez le système de couleurs à l’aide des boutons
▲ ou ▼.
Système Sonore → BG / DK / I / L: Sélectionnez le système audio à l’aide des boutons ▲ ou ▼.
Canal (si vous connaissez le numéro de la chaîne à mémoriser): Appuyez sur le bouton ▲ ou ▼ pour sélectionner C (canal
hertzien) ou S (canal câblé). Appuyez sur le bouton ►, puis sur le bouton ▲ ou ▼ ou un chiffre (0-
9) pour sélectionner le
numéro de votre choix.
Vous pouvez également sélectionner le numéro de chaîne directement en appuyant sur le pavé numérique (0-
9).
Si aucun son ne sort ou si celui-ci est anormal, sélectionnez à nouveau la norme son requise.
Recherche (lorsque vous ne connaissez pas les numéros de chaîne): Appuyez sur le bouton ▲ ou ▼ pour lancer la
recherche. Le syntoniseur balaie la plage de fréquences jusqu’à ce que vous receviez la première chaîne ou la chaîne que
vous avez sélectionnée à l’écran.
Mémoriser (Permet de mémoriser la chaîne et le numéro de programme correspondant): Sélectionnez OK en appuyant
sur le bouton ENTER
E
.
Mode des chaînes
P (Mode Programme): A la n du réglage, des numéros de position compris entre P00 et P99 sont attribués aux
stations de radiodiffusion de votre région. Dans ce mode, vous pouvez sélectionner un canal en saisissant son
numéro de position.
C (Mode chaîne hertzienne): dans ce mode, vous pouvez sélectionner un canal en saisissant le numéro attribué à
chacune des stations de télédiffusion.
S (Mode chaîne câblée): dans ce mode, vous pouvez sélectionner une chaîne en saisissant le numéro attribué à
chacune des chaînes câblées.
Guide Complet / Mini Guide
Les informations relatives au Guide de programme électronique (EPG) sont fournies par les émetteurs. Les entrées de
programmes peuvent apparaître en blanc ou ne pas être à jour en raison de l’information diffusée sur un canal donné.
L’afchage fera une mise à jour automatique dès qu’une nouvelle information sera disponible.
Pour obtenir plus de détails sur les procédures d’utilisation du Mini Guide
et du Guide Complet, reportez-vous aux descriptions de la page 13.
Vous pouvez aussi afcher le guide en appuyant simplement sur le bouton
GUIDE. (Pour congurer le Par défaut, reportez-vous aux descriptions.)
Guide Complet
: Afche le programme heure par heure. Deux heures de programme sont afchées et vous pouvez faire
déler le programme en avançant ou en remontant dans le temps.
Mini Guide
: Les informations de chaque programme sont afchées ligne par ligne sur l’écran Mini-guide de la chaîne
actuelle, en commençant par le programme en cours, dans l’ordre des heures de début des programmes.
❑
•
•
•
N
N
N
N
N
❑
N
N
•
•
•
N
•
•
•
•
N
N
•
•
N
-
-
-
❑
N
O
Page 76
Français - 13
Par défaut
Mini Guide /
Guide Complet: Vous pouvez choisir d’afcher soit le Mini Guide soit
le Guide Complet lorsque vous appuyez sur le bouton GUIDE de la télécommande.
Liste des chaînes
Pour obtenir plus de détails sur les procédures d’utilisation de la Liste des
chaînes, reportez-vous aux descriptions des pages 14 ~15.
Mode Canal
Appuyez sur le bouton P >/<, L’ordre des chaînes afchées change.
Chaînes ajoutées
: L’ordre des chaînes change dans la liste des chaînes
mémorisées.
Favoris
: L’ordre des chaînes change dans la liste des chaînes favorites.
Réglage n
Si la réception est nette, vous n’avez pas besoin d’effectuer un réglage n du canal, car cette opération s’effectue
automatiquement pendant la recherche et la mémorisation. Si le signal est faible ou déformé, vous pouvez être amené à
effectuer manuellement un réglage n du canal.
Les canaux réglés et mémorisés sont repérés par un astérisque * placé à droite de leur numéro dans la bannière des
canaux.
Pour réinitialiser le réglage, sélectionnez Réinitialiser à l’aide du bouton ▲ ou ▼, puis appuyez sur le bouton ENTER
E
.
La syntonisation ne est possible uniquement avec les chaînes analogiques.
Informations de signal
Vous pouvez obtenir des informations relatives à l’état du signal.
Si l'état du signal est faible, le message Signaux Faibles ou Inexistants s'afche.
Cette fonction peut être sélectionnée pendant que vous regardez une chaîne numérique.
Les informations techniques concernant l'état du signal sont afchées.
- Fréquence / ID de service/Multiplex/Réseau/Niveau d’erreurs binaires/Force du signal
LNA → Arrêt / Marche
Si la télévision fonctionne dans une zone où le signal est faible, la fonction LNA (Low Noise Amplier) peut parfois améliorer
la réception (un préamplicateur à faible bruit augmente le signal d’arrivée).
Cette fonction peut être sélectionnée pendant que vous regardez une chaîne analogique.
Utilisation du guide complet/mini-guide
▲/▼/◄/►,
(ENTER)
Sélectionnez un programme en appuyant sur le bouton ▲/▼/◄/►.
Si le programme suivant est sélectionné, il est réglé avec l'icône de l'horloge affiché. Si vous appuyez
à nouveau sur le bouton ENTER, puis sur ▲/▼/◄/► pour sélectionner Annuler horaires, la
programmation est annulée et l'icône de l'horloge disparaît.
Pour plus d'informations sur la programmation des programmes, reportez-vous à la section.
ROUGE
Basculer entre Mini Guide et Guide Complet.
VERT
Guide Complet: Reculer rapidement (24 heures).
Mini Guide: Afficher rapidement la page suivante.
JAUNE
Guide Complet: Avancer rapidement (24 heures).
Mini Guide
: Afficher rapidement la page précédente.
BLEUQuitter le guide.
INFO
Le bouton INFO permet d'obtenir des informations détaillées. Numéro de canal, temps de
fonctionnement du programme, barre d'état, niveau de contrôle parental, informations sur la qualité
vidéo (HD/SD), modes sonores, sous-titres ou Teletext, Langue des sous-titres ou du Teletext et bref
résumé du programme surligné font partie des informations supplémentaires. “…” apparaîtra si le
résumé est long.
❑
❑
❑
❑
N
N
N
❑
N
N
N
❑
N
Canal
Réglage fin
Informations de signal
LNA : Arrêt
►
Guide Complet
DTV Cable 900 f tn 2:10 Tue 1 Jun
Freshmen Marche Campus
2:00 - 2:30
No Detailed Information
Aujourd’hui2:00 - 3:003:00 - 4:00
Mint Extra
Loaded
Fresh 40 with Dynamite MC
The Distillery
Smash Hits! Sunday
900 f tn
901 ITV Sélection
902 Kerrang!
903 Kiss
903 oneword
903 Smash Hits!
▼
Street Hypn...
Kisstory
Pas d’information
Pas d’information
Pas d’information
Freshmen O...
Voir
Information
Mini Guide +24 Heures Quitter
Mini Guide DTV Câble 900 f tn
Street Hypnosis
Booze Britain
2:00
2:30
5:00
▼
Freshmen Marche Campus
Voir
Information
Guide Complet Page suiv. Quitter
Page 77
Français - 14
Gestion des chaînes
Ce menu permet d’ajouter/supprimer ou dénir des chaînes favorites et d’utiliser le
guide des programmes pour les émissions numériques.
Sélectionnez une chaîne dans l'écran Tous Tous les canaux, Chaînes ajoutées, Favoris ou Programmé en appuyant sur les boutons
▲ / ▼, puis sur le bouton ENTER
E
.
Tous les canaux
: Affiche toutes les chaînes actuellement disponibles.
Canaux ajoutés
: Affiche toutes les chaînes ajoutées.
Favoris
: Affiche toutes les chaînes favorites.
Programmé: Afche tous les programmes actuellement réservés.
Utilisation des boutons de couleur dans la liste des chaînes
Rouge (Type de chaîne): Permet de basculer entre TV, Radio, Donn/autre
et Tous.
Vert (Zoom): Agrandit ou réduit une chaîne.
Jaune (Sélectionner): Sélectionne des listes de chaînes.
TOOLS (Option) : Afche le menu Supprimer (ou Ajouter), Ajouter aux
favoris (ou Supprimer des favoris), Verrouil. (ou Déverr.), Ecoute
programmée, Modi. nom de chaîne, Tri des canaux, Modi. nom de
chaîne, Sélectionner tout, Désélectionner tout ou Mémorisation Auto.
(Les menus Options peuvent varier en fonction de la situation.)
Icônes d’état des chaînes
A
Chaîne analogique.
c
Chaîne sélectionnée en appuyant sur le bouton jaune.
♥
Chaîne dénie comme Favorite.
(
Programme en cours de diffusion.
\
Chaîne verrouillée.
)
Programme réservé
Menu d’options de la liste des chaînes (dans Tous les canaux / Canaux ajoutés / Favoris)
Appuyez sur le bouton TOOLS pour utiliser le menu d’options.
Les éléments du menu Options peuvent varier selon la chaîne.
Ajouter / Supprimé
Vous pouvez supprimer ou ajouter une chaîne an d’afcher les chaînes de votre choix.
Toutes les chaînes supprimées apparaîtront dans le menu Tous les canaux.
Une chaîne grisée est une chaîne qui a été supprimée.
Le menu
Ajouter
apparaît uniquement pour les chaînes supprimées.
De la même manière, vous pouvez également ajouter une chaîne au menu
Canaux ajoutés ou Favoris.
Ajouter aux favoris / Supprimer des favoris
Vous pouvez dénir comme favorites les chaînes que vous regardez souvent.
Le symbole ♥ s’afche et la chaîne est dénie comme favorite.
Toutes les chaînes favorites apparaîtront dans le menu Favoris.
Verrouil. / Déverr.
Vous pouvez verrouiller une chaîne an qu’elle ne puisse pas être sélectionnée ni visualisée. Cette fonction n’est disponible
que lorsque la fonction Verrouillage Canal est à Marche. (Voir page 23)
L’écran de saisie du code PIN apparaît. Entrez votre code PIN à quatre chiffres.
Le code PIN par défaut d’un nouveau téléviseur est “0-0-0-0”. Vous pouvez modier le code PIN en sélectionnant
Modier PIN dans le menu.
Le symbole \ s’afche et la chaîne est verrouillée.
Ecoute programmée
Si vous réservez un programme que vous souhaitez regarder, la chaîne bascule automatiquement vers la chaîne réservée
dans la liste de chaînes, même lorsque vous êtes en train de regarder une autre chaîne. Pour réserver un programme, réglez
d’abord l’heure actuelle. (reportez-vous à la page 26)
Seules les chaînes mémorisées peuvent être sélectionnées.
Vous pouvez régler directement la chaîne, le mois, le jour, l’heure et les minutes à l’aide du pavé numérique de la
télécommande.
Toutes les chaînes supprimées apparaîtront dans le menu Programmé.
Guide des programmes numérique et afchage des réservations
Lorsqu’une chaîne numérique est sélectionnée et que vous appuyez sur le bouton ►, le Guide des programmes de la
chaîne apparaît. Vous pouvez réserver un programme en suivant les procédures décrites ci-dessus.
N
N
-
-
-
-
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
Canal
Mini Guide
Par défaut : Mini Guide
Liste des chaînes
Mode Canal : Chaînes ajoutées
Réglage fin
Informations de signal
LNA : Arrêt
824 UKTV Gold
825 UKTV style
A
1 C --
A
2 C
--
A 3 ♥ C
--
A 4 C
--
A 5 C
--
A 6 C
--
A 7 C
--
A 8 C
--
Chaînes ajoutées
Tous
Type de canal Zoom Sélection
Option
824 UKTV Gold
825 UKTV style
A
1 C --
A
2 C
--
A 3 C
--
A 4 C
--
A 5 C
--
A 6 C
--
A 7 C
--
A 8 C
--
Tous les canaux
Tous
Type de canal Zoom Sélection
Option
Supprimer
Ajouter aux favoris
Verrouil.
Ecoute programmée
Modifi. nom de chaîne
Tri des canaux
▼
Page 78
Français - 15
Modifi. nom de chaîne (chaîne analogique uniquement)
Les chaînes peuvent recevoir un libellé qui s’afchera chaque fois que la chaîne est sélectionnée.
Les chaînes numériques ont des noms qui leur sont automatiquement attribués et ne peuvent pas être modiés.
Vous pouvez également modier le numéro de chaîne à l’aide du pavé numérique de la télécommande.
Tri des canaux
Cette opération vous permet de changer les numéros de programme des canaux mémorisés. Cette opération peut s’avérer
nécessaire après l’utilisation de la mémorisation automatique.
Cette fonction n'est disponible qu'en mode analogique.
Sélectionner tout / Désélectionner tout
Sélectionner tout: Vous pouvez sélectionner toutes les chaînes de la liste des chaînes.
Désélectionner tout: Vous pouvez désélectionner toutes les chaînes sélectionnées dans la liste des chaînes.
Vous pouvez appliquer les fonctions Ajouter/Supprimer, Ajouter aux favoris/Supprimer des favoris,ou Verrouil./
Déverrouiller à plusieurs chaînes à la fois. Sélectionnez les chaînes voulues et appuyez sur le bouton jaune pour traiter
toutes les chaînes sélectionnées à la fois.
La marque c s’afche à gauche des chaînes sélectionnées.
La fonction Désélectionner tout n’est disponible que si au moins une chaîne est sélectionnée.
Mémorisation Auto
Pour plus d’informations concernant le réglage des options, reportez-vous à la page 11.
Si une chaîne est verrouillée par la fonction Verrouillage Canal, la fenêtre de saisie du code PIN s’afche.
Menu d’options de la liste des chaînes (dans Programmé)
Vous pouvez voir, modier ou supprimer une réservation.
Appuyez sur le bouton TOOLS pour utiliser le menu d’options.
Infos modif.
: Permet de modifier une réservation.
Annuler progr.
: Permet d’annuler une réservation.
Information
: Permet de visualiser une réservation (et d’en changer les
données).
Sélectionner tout
: Sélectionne tous les programmes réservés.
N
N
•
•
N
N
N
N
N
N
Réglage de l’image
Modification et rétablissement des paramètres d’image
Mode
Vous pouvez sélectionner le type d’image qui correspond le mieux à vos
exigences d’afchage.
Dynamique
: Sélectionne l’image pour un affichage haute définition dans une
pièce claire.
Standard
: Sélectionne l’image pour un affichage optimal dans un
environnement normal.
Cinéma
: Sélectionne l’image pour un affichage agréable de films dans une
pièce sombre.
Appuyez sur le bouton TOOLS pour afcher le menu Outils.
Vous pouvez également dénir le mode d’image en sélectionnant Outils → Mode Image.
Sélectionnez un mode d’image à ajuster. Les valeurs ajustées sont enregistrées pour tous les modes d’image.
Lorsque vous modiez les paramètres Lum. Cellules, Contraste, Luminosité, Netteté, Couleur ou Teinte(
V
/R), l’écran
se modie en conséquence.
En mode Analog TV, Ext., AV, S-Video du système PAL, vous ne pouvez pas utiliser la fonction Teinte.
En mode PC, vous ne pouvez modier que les options Lum. Cellules, Contraste et Luminosité.
Vous pouvez effectuer des réglages pour chaque appareil externe connecté à une entrée du téléviseur et les enregistrer.
L’énergie consommée pendant le fonctionnement peut être sensiblement réduite en baissant le niveau de luminosité de
l’image. Cela réduira le coût de fonctionnement général.
Réglages des détails
Les nouveaux téléviseurs Samsung permettent d’effectuer des réglages
d’image encore plus précis que les modèles précédents. Ce qui suit explique
comment régler les paramètres détaillés de l’image.
Réglages des détails est disponible dans les modes Standard et
Cinéma.
En mode PC, vous ne pouvez modier que les options Contraste Dynam.,
Gamma et Balance blancs parmi les Réglages des détails.
Réglage des noirs → Arrêt / Bas / Moyen / Elevé
Vous pouvez choisir le niveau de noir sur l’écran pour régler la profondeur de
l’écran.
Contraste Dynam.
→ Arrêt / Bas / Moyen / Elevé
Vous pouvez régler le contraste de l’écran pour obtenir un contraste optimal.
Gamma
Vous pouvez régler l’intensité des couleurs primaires (rouge, vert, bleu).
Espace couleur
Un espace de couleur est une matrice de couleurs composée de rouge, de vert et de bleu. Sélectionnez votre espace de
couleur préféré et appréciez la couleur la plus naturelle.
Auto.: règle automatiquement la nuance de couleur naturelle sur la base des programmes sources.
Natif: offre une nuance de couleur foncée et riche.
Personnel: règle la gamme de couleurs en fonction de vos préférences
Permet de régler la gamme de couleurs en fonction de vos préférences Couleur est disponible lorsque l”option
Espace couleur est dénie sur Personnalisé.
Rouge / Vert / Bleu: Dans Couleur, vous pouvez régler les valeurs RVB de la couleur sélectionnée.
Réinit.: rétablit les valeurs par défaut de l’espace de couleur.
Balance blancs
Vous pouvez régler la température des couleurs pour que celles-ci soient plus naturelles.
Aj. Rouge / Aj. Vert / Aj. Bleu / Regl. Rouge / Regl. vert / Regl. bleu: La modication des valeurs de réglage permet
d’actualiser l’écran que vous venez de retoucher.
Réinit.: l’équilibrage du blanc réglé précédemment est ramené à sa valeur par défaut.
Carnation
Vous pouvez accentuer le 'ton chair' de l’image.
La modication des valeurs de réglage permet d’actualiser l’écran que vous venez de retoucher
.
Amélioration des bords → Arrêt / Marche
Vous pouvez faire ressortir la bordure des objets sur l’image.
xvYCC → Arrêt / Marche
L’activation du mode xvYCC augmente les détails et l’espace de couleur lorsque vous regardez des lms depuis un
périphérique externe (ex. : lecteur DVD).
xvYCC est disponible lorsque le mode d’image est déni sur Cinéma et la sortie externe sur le mode HDMI ou
Composant.
Si la fonction xvYCC est active, la fonction PIP ne peut pas être sélectionnée.
Options d'image
En mode PC, vous ne pouvez modier que les options Nuance Coul.,
Format et Protec brûl. ècran Protection dans le menu Options d'image.
Nuance Coul.
→ Froide2 / Froide1 / Normal / Chaude1 / Chaude2
Vous pouvez sélectionner la nuance de couleur la plus agréable au regard.
Les valeurs réglées sont mémorisées en fonction du mode Image
sélectionné.
Chaude1 ou Chaude
2 ne sont activées que lorsque le mode d’image est
Cinéma.
N
N
N
N
N
N
❑
N
N
•
•
•
N
-
-
-
-
•
•
N
N
N
❑
N
N
N
Couleur : 50
Teinte (R / G) : V50 / R50
Réglages des détails ►
Options d'image
Réinitialisation de l’image
Image
Teinte (V/R) : V50 / R50
Réglages des détails
Options d'image ►
Réinitialisation de l’image
Image
Page 80
Français - 17
Format
Vous pouvez sélectionner la taille d’image qui correspond le mieux à vos besoins d’afchage.
Appuyez sur le bouton TOOLS pour afcher le menu Outils.
Vous pouvez également dénir la taille en sélectionnant Outils → Format de l'image.
1
6/9 auto: Règle automatiquement la taille de l’image au format 1
6:9.
16:9: Règle la taille de l’image sur 16:9 de façon appropriée pour les DVD ou la diffusion au format cinémascope.
Zoom large: Agrandit l’image à une taille supérieure à 4:3.
Zoom: Agrandit l’image en 16:9 (dans la direction verticale) pour l’adapter à la taille de l’écran.
4:3: C’est le paramètre par défaut pour un lm cinéma ou de la diffusion normale.
Scan uniquement: Utilisez la fonction pour voir l’intégralité de l’image sans coupure lors de les signaux HDMI (720p/1080i/
1080p) ou Component (1080i/1080p) sont entrés.
Les options de taille de l’image peuvent varier en fonction de la source d’entrée.
Les éléments disponibles peuvent varier en fonction du mode sélectionné.
En mode PC, seuls les modes 1
6:9 et 4:3 peuvent être sélectionnés.
Vous pouvez effectuer des réglages pour chaque appareil externe connecté à une entrée du téléviseur et les
enregistrer.
Une rémanence temporaire peut se produire lorsque vous afchez une image statique pendant une ou deux heures sur
l’écran du téléviseur.
Zoom large: Appuyez sur le bouton ► pour sélectionner Position, puis appuyez sur le bouton ENTER
E
. Utilisez le
bouton ▲ ou ▼ pour déplacer l’écran vers le haut ou le bas. Appuyez ensuite sur le bouton ENTERE.
Zoom: Appuyez sur le bouton ► pour sélectionner Position, puis appuyez sur le bouton ENTER
E
. Appuyez le
bouton ▲ ou ▼ pour déplacer l’image vers le haut et vers le bas. Appuyez ensuite sur le bouton ENTER
E
. Appuyez
sur le bouton ► pour sélectionner
Taille
, puis appuyez sur le bouton ENTERE. Appuyez sur le bouton ▲ ou ▼ pour
agrandir ou réduire la hauteur de l’image. Appuyez ensuite sur le bouton ENTERE.
Après avoir sélectionné l’option Scan uniquement en mode HDMI (1080i/1080p) ou Component (1080i/1080p):
Sélectionnez Position à l’aide du bouton ◄ ou ►. Utilisez le bouton ▲, ▼, ◄ ou ► pour déplacer l’image. Réinitialiser: Appuyez sur le bouton ◄ ou ► pour sélectionner Réinitialiser, puis appuyez sur le bouton ENTER
E
.
Vous pouvez initialiser le réglage.
Si vous utilisez la fonction Scan uniquement avec l’entrée HDMI 720p, une ligne sera coupée en haut, en bas, à
gauche et à droite, comme avec la fonction overscan.
Lorsque le mode Double (
, ) a été déni dans PIP, le paramètre Format de l’image ne peut pas être réglé.
Mode écran → 16:9 /
Zoom large
/ Zoom / 4:3
Lorsque vous xez la taille de l’image à 16/9 auto sur un téléviseur 16:9, vous pouvez déterminer la taille selon laquelle vous
voulez afcher une image 4:3 WSS (Wide Screen Service, service d’écran large) ou rien. Chaque pays européen emploie une
taille d’image ; cette fonction permet aux utilisateurs de sélectionner la leur.
16:9: Règle l’image en mode large, c’est-à-dire en 16:9.
Zoom large: Agrandit l’image à une taille supérieure à 4:3.
Zoom: agrandit la taille de l’image sur l’écran dans le sens vertical.
4:3: règle l’image en mode normal, c’est-à-dire en 4:3.
Cette fonction n’est disponible qu’en mode 1
6/9 auto.
Cette fonction n’est pas disponible en mode PC, Composante ou HDMI.
NR numérique → Arrêt / Bas / Moyen / Elevé / Auto.
Si le signal de radiodiffusion reçu est faible, vous pouvez activer la fonction Digital Noise Reduction pour favoriser la réduction
d’images fantômes ou statiques qui peuvent apparaître à l’écran.
Lorsque le signal est faible, sélectionnez une autre option jusqu’à obtention de la meilleure image possible.
DNIe → Arrêt / Démo / Marche
Pour offrir une grande qualité d’image, ce téléviseur est doté de la fonction DNIe. Si vous dénissez l’option DNIe sur On,
la fonction DNIe sera activée à l’écran. Lorsque vous activez le mode Démo de la fonction DNIe, une image normale et
une image avec la fonction DNIe appliquée s’afchent à l’écran à des ns de démonstration. Cette fonction vous permet de
constater la différence de qualité d’afchage.
DNIe™ (Digital Natural Image engine)
DNIe™
Cette fonction vous offre une image plus détaillée tout en permettant une réduction de bruit 3D et une amélioration des détails,
des contrastes et des blancs. Le nouvel algorithme de compensation d’images vous offre une image plus lumineuse, plus
claire et plus détaillée. La technologie DNIe™ adapte tous les signaux à votre vue, quels qu’ils soient.
Cette fonction n’est pas disponible en mode Cinéma ni Standard.
Niv. noir HDMI → Normal / Bas
Vous pouvez directement choisir le niveau de noir sur l’écran pour régler la profondeur de l’écran.
Cette fonction n’est active que lorsque l’entrée externe se connecte à HDMI (signaux RVB).
T
•
•
•
•
•
•
N
N
N
N
N
N
N
N
N
N
N
•
•
•
•
N
N
N
N
N
N
Page 81
Français - 18
Démo 100Hz réel→ Arrêt / Marche
Vous pouvez clairement voir la différence entre Démo 100Hz réel et 50 Hz, surtout lorsque vous regardez des scènes
rapides. Lorsqu’une image lente est affichée, vous ne serez pas en mesure de faire la distinction entre Démo 100Hz réel et 50Hz. La fonction Démo 100Hz n’est disponible qu’avec un signal 50Hz. Le mode Démo 100Hz réel est fourni pour des
démonstrations en magasin avec des images spéciales.
Movi
e Plus →
Arrêt
/ Bas / Moyen / Elevé / Démo
Vous pourrez apprécier des images plus naturelles et des textes plus nets et ce, même dans les scènes rapides.
Utilisez cette fonction lorsque vous regardez un film.
Cette fonction n’est pas disponible dans les Zoom large large et Zoom.
Cette fonction n'est pas disponible lorsque PIP est défini sur Marche.
Elle n'est pas prise en charge en mode HDMI 1080p/24 Hz, 25Hz, 30Hz.
Mode bleu uniquement → Arrêt / Marche
Cette fonction est destinée aux spécialistes de mesure des appareils AV. Cette fonction affiche le signal bleu en supprimant
simplement les signaux rouge et vert du signal vidéo, de manière à fournir un effet Filtre bleu utilisé pour régler la couleur et
la teinte de l'équipement vidéo, tel que des lecteurs de DVD, systèmes de cinéma à domicile, etc. Cette fonction permet de
régler la couleur et la teinte sur des valeurs appropriées au niveau de signal de chaque dispositif vidéo à l'aide des modèles
de barres de couleurs Rouge/Vert/Bleu/Cyan/Magenta/Jaune, sans utiliser de filtre bleu supplémentaire.
Mode bleu uniquement n'est disponible que si le mode Image est déni sur Cinéma ou Standard.
Protec brûl. ècran
Pour réduire le risque de brûlure d'écran, cet écran est équipé d'une technologie de prévention des brûlures. Cette fonction
permet de régler le mouvement de l'image de bas en haut (ligne verticale) et de gauche à droite (point horizontal). Le réglage
de l'horloge permet de programmer en quelques minutes la durée séparant les mouvements de l'image.
Modif. pixel: Cette fonction permet de déplacer les pixels sur l'écran dans le sens vertical ou horizontal, afin d'éviter une
image résiduelle sur l'écran.
Appuyez sur le bouton ▲ or ▼ pour activer (Marche) la fonction Modif. pixel, puis sur ENTER.
Sélectionnez l'option souhaitée en appuyant sur le bouton ▲ or ▼, puis sur ENTER.
Options disponibles: Nbre point horizont., Nbre ligne vertic.,Horloge.
Conditions optimales pour la modification des pixels.
PCTV/Ext/AV/Composant/HDMI
Nbre point horizont.44
Nbre ligne vertic.44
Horloge (minutes)42 min
La valeur de Pixel Shift peut changer selon le mode et la taille du moniteur (pouces).
Cette fonction n'est pas disponible en mode Scan uniquement.
Ecran blanc: cette fonction contribue à supprimer les images résiduelles à l'écran en modifiant la couleur des pixels
pour les rendre blancs. Utilisez cette fonction lorsque des images résiduelles ou des symboles apparaissent à l'écran, en
particulier lorsque vous affichez une image fixe à l'écran pendant une longue période.
Défilement: cette fonction contribue à supprimer les images résiduelles à l'écran en déplaçant tous les pixels sur l'écran
à plasma, selon un motif prédéfini. Utilisez cette fonction lorsque des images résiduelles ou des symboles apparaissent à
l'écran, en particulier lorsque vous affichez une image fixe à l'écran pendant une longue période.
Gris de bord: si vous regardez la télévision dans un rapport d'écran 4:3, l'écran est protégé contre tout dommage grâce à
l'ajustement de la balance des blancs sur les côtés gauche et droit.
Sombre: si le rapport d'écran est défini sur 4:3, les bords gauche et droit sont assombris.
Clair: si le rapport d'écran est défini sur 4:3, les bords gauche et droit sont éclaircis.
Réinitialisation de l’image → Réinitial. mode image / Annuler
Rétablit toutes les valeurs par défaut de l’image.
Sélectionnez un mode d’image à rétablir. La fonction de réinitialisation est exécutée pour chaque mode d’image.
N
N
N
N
N
•
N
N
N
N
N
N
•
•
•
-
-
❑
N
Page 82
Français - 19
Visualisation d’une image dans l’image
Vous pouvez afcher une image secondaire dans l’image principale du programme
télévisé ou de l’entrée vidéo. De cette manière, vous pouvez regarder ou surveiller
le programme télévisé ou l’entrée vidéo depuis n’importe quel équipement branché
tout en regardant l’image principale.
Il est possible que l’image dans la fenêtre PIP devienne légèrement moins
naturelle lorsque vous utilisez l’écran principale pour un jeu ou un karaoké.
Appuyez sur le bouton TOOLS pour afcher le menu Outils.
Vous pouvez également congurer les paramètres PIP en sélectionnant
Outils → PIP.
PIP → Arrêt / Marche
Vous pouvez activer ou désactiver la fonction PIP.
Image principaleImage secondaire
Component
HDMI 1, HDMI2/DVI, HDMI 3,
HDMI 4
PC
TV, Ext.1, Ext.2, AV
Source
Vous pouvez sélectionner la source de l’image secondaire.
Format → / /
Vous pouvez sélectionner la taille de l’image secondaire.
Si l’image principale est en mode HDMI, l’option Format n’est pas accessible.
Position → / / /
Vous pouvez sélectionner la position de l’image secondaire.
En mode Double (
, ), l’option Position ne peut pas être sélectionnée.
Canal
Vous ne pouvez sélectionner une chaîne de l’image secondaire que si la Source est dénie sur TV.
Appuyez sur le bouton TOOLS pour afcher le menu Outils.
Vous pouvez également dénir le mode Image en sélectionnant Outils → PIP.
N
T
❑
N
N
T
Conguration
Divertissement : Arrêt
Mode éco. : Arrêt
PIP ►
Mise à niveau du logiciel
Interface commune
PIP
PIP : Marche
Source : TV
Format :
Position :
Canal : ATV 11
L
Déplacer E Entrer R Retour
Configuration du téléviseur avec le PC
Préréglage: Appuyez sur le bouton SOURCE pour sélectionner le mode PC.
Réglage Automatique
Le réglage automatique permet à l’écran PC afché sur le téléviseur d’être
ajusté automatiquement en fonction du signal vidéo PC. Les valeurs des options
Regl. Prec, Regl. Base et Position sont dénies automatiquement.
Cette fonction ne s’applique pas en mode DVI-HDMI.
Appuyez sur le bouton TOOLS pour afcher le menu Outils.
Vous pouvez également dénir le réglage automatique en sélectionnant
Outils → Réglage Automatique.
Ecran
Regl. Base
/
Regl. Prec: Lorsque vous réglez la qualité de l’image, l’objectif est d’éliminer ou de réduire les parasites
visuels. Si ces parasites ne sont pas éliminés uniquement avec une syntonisation ne (Fine-tuning), réglez la fréquence
du mieux que vous pouvez (Coarse), puis effectuez à nouveau une syntonisation plus ne. Une fois les parasites réduits,
effectuez un nouveau réglage de l’image pour l’aligner au centre de l’écran.
PC Position
: Réglez la position de l’écran du PC si elle ne convient pas à l’écran du téléviseur. Appuyez sur le bouton
▲ ou ▼ pour régler la position verticale. Appuyez sur le bouton ◄ ou ► pour régler la position horizontale.
Réinitialiser Image
: Vous pouvez rétablir les valeurs par défaut de tous les réglages d’image.
N
❑
N
T
❑
Rétroéclairage : 45
Netteté : 50
Réglage Automatique
►
Ecran
Réglages des détails
Options d'image
Réinitialisation de l’image
Image
Page 83
Français - 20
Ecran du PC
Conguration de votre logiciel PC (instructions basées sur Windows XP)
Les paramètres d’afchage Windows indiqués ci-dessous sont ceux d’un ordinateur
type. L’écran de votre PC sera probablement différent, selon votre version de
Windows et votre carte vidéo. Cependant, même si les afchages diffèrent, les
informations de conguration de base s’appliquent dans la plupart des cas. Dans
le cas contraire, contactez le fabricant de votre ordinateur ou votre revendeur
Samsung.
1. Cliquez sur ‘Panneau de conguration” dans le menu Démarrer de Windows.
2
. Lorsque vous êtes sur l’écran du panneau de conguration, cliquez sur
“Apparence et thèmes” et une boîte de dialogue apparaît.
3. Cliquez sur “Afchage”. Une boîte de dialogue vous propose des options
d’afchage.
4. Sélectionnez l’onglet ‘Paramètres’ dans la boîte de dialogue Propriétés de
l’Afchage.
Réglage correct de la taille (résolution)
Optimal : 1920 x 1080 pixels.
S’il existe une option de fréquence verticale sur votre boîte de dialogue des
paramètres d’afchage, la valeur correcte est “60” ou “60Hz”. Sinon, cliquez
simplement sur “OK” pour quitter la boîte de dialogue.
Modes d’afchage
La taille et la position de l’écran varient en fonction du type d’écran du PC et de sa résolution.
Les résolutions indiquées dans le tableau sont recommandées.
Entrée D-Sub
ModeRésolution
Fréquence
horizontale (kHz)
Fréquence verticale
(Hz)
Fréquence
d’horloge pixels
(MHz)
Polarité
synchronisée
(H/V)
IBM
640
x 350
720 x 400
31.469
31.469
70.086
70.087
25.175
28.322
+ / -
- / +
VESA
640
x 480
640 x 480
640 x 480
800 x 600
800 x 600
800 x 600
1024 x 768
1024 x 768
1024 x 768
1280 x 1024
1280 x 1024
1360 x 768
1600 x 1200
31.469
37.861
37.500
37.879
48.077
46.875
48.363
56.476
60.023
63.981
79.976
47.712
75.000
59.940
72.809
75.000
60.317
72.188
75.000
60.004
70.069
75.029
60.020
75.025
60.015
60.000
25.175
31.500
31.500
40.000
50.000
49.500
65.000
75.000
78.750
108.000
135.000
85.500
162.000
- / -
- / -
- / + / +
+ / +
+ / +
- / -
- / + / +
+ / +
+ / +
+ / +
+ / +
CVT1920 x 1080 RB66.58759.934138.500+ / -
Entrée HDMI/DVI
ModeRésolution
Fréquence
horizontale (kHz)
Fréquence verticale
(Hz)
Fréquence
d’horloge pixels
(MHz)
Polarité
synchronisée
(H/V)
VESA
640
x 480
800 x 600
1024 x 768
1280 x 1024
1360 x 768
1600 x 1200
31.469
37.879
48.363
63.981
47.712
75.000
59.940
60.317
60.004
60.020
60.015
60.000
25.175
40.000
65.000
108.000
85.500
162.000
- / + / +
- / + / +
+ / +
+ / +
CEA1920 x 1080p67.500 60.000148.500 + / +
Lorsque vous utilisez une connexion avec câble HDMI/DVI, vous devez utiliser la borne HDMI IN
2.
Le mode entrelacé n’est pas pris en charge.
Le téléviseur peut fonctionner de façon anormale si un format vidéo non standard est sélectionné.
Les modes Separate (Séparé) et Composite (Composite) sont pris en charge. SOG (SVSV) n’est pas pris en charge.
Un câble
VGA trop long ou de qualité médiocre peut être source de parasites visuels dans les modes haute résolution
(1 920 x 1 080).
N
N
N
N
N
Page 84
Français - 21
Réglage du son
Changement de la norme Son
Mode → Standard / Musique / Cinéma / Parole / Personnel
Vous pouvez sélectionner le type d’effet sonore souhaité lorsque vous regardez
un programme donné.
Appuyez sur le bouton TOOLS pour afcher le menu Outils.
Vous pouvez également dénir le mode audio en sélectionnant Outils → Mode Son.
Egaliseur
Les paramètres du son peuvent être réglés selon vos préférences personnelles.
Mode
: Vous pouvez sélectionner un mode sonore à votre convenance.
Balance
: Définit la balance entre les haut-parleurs droit et gauche.
100Hz / 300Hz / 1kHz / 3kHz / 10kHz
(Réglage de la bande passante): Permet de régler le niveau de fréquences de la
bande passante.
Reset
: rétablit les valeurs par défaut de l’égaliseur.
SRS TruSurround XT → Arrêt / Marche
Le TruSurround XT est une technologie SRS brevetée qui remédie au problème de la lecture du contenu d’un disque
multicanal 5,1 sur deux haut-parleurs. Le TurSurround produit un son surround virtuel fascinant au moyen de n’importe quel
système de lecture à deux haut-parleurs, dont les haut-parleurs internes du téléviseur. Il s’adapte parfaitement à tous les
formats multicanaux.
Appuyez sur le bouton TOOLS pour afcher le menu Outils.
Vous pouvez également dénir l’option SRS TruSurround XT en sélectionnant Outils → SRS TS XT.
TruSurround XT, SRS et le symbole sont des marques de SRS Labs, Inc. La technologie TruSurround XT est protégée par la licence de SRS Labs, Inc.
Langue audio
Vous pouvez modier la langue par défaut des sous-titres et de l’audio. Afche les informations relatives à la langue pour le
ot d’entrée.
Cette fonction peut être sélectionnée pendant que vous regardez une chaîne numérique.
Vous pouvez sélectionner la langue uniquement parmi les langues en cours de diffusion.
Format Audio → MPEG / Dolby Digital
Lorsque le son est émis à la fois par le haut-parleur principal et le récepteur audio, un effet d’écho peut se produire en raison
de la différence de vitesse de décodage entre le haut-parleur principal et le récepteur audio. Dans ce cas, utilisez la fonction
Haut-parleur TV.
Cette fonction peut être sélectionnée pendant que vous regardez une chaîne numérique.
Vous pouvez sélectionner la langue uniquement parmi les langues en cours de diffusion.
Fabriqué sous licence de Dolby Laboratories. Dolby et le symbole du double D sont des
marques déposées des laboratoires Dolby.
Description audio
Il s’agit d’une fonction audio auxiliaire qui fournit une piste audio supplémentaire à l’intention des personnes malvoyantes.
Cette fonction traite le ux audio relatif à la Description audio (AD) lorsqu’il est envoyé avec le son principal par le
radiodiffuseur. Les utilisateurs peuvent activer ou désactiver la description audio et régler le volume.
Description audio
→ Arrêt / Marche: Active ou désactive la fonction de description audio.
Volume
: Permet d’ajuster le volume de la description audio.
Volume est actif lorsque Description audio est déni à Marche.
Cette fonction peut être sélectionnée pendant que vous regardez une chaîne numérique.
❑
T
❑
❑
T
❑
N
N
❑
N
N
❑
N
N
Mode : Personnel
►
Egaliseur
SRS TruSurround XT : Arrêt
Langue audio : ---Format Audio : ---Description audio
Auto
Volume : Arrêt
Sélection Haut-parleur :
Haut-parleur TV
align
Page 85
Français - 22
Sélection du mode Son
Vous pouvez congurer le mode sonore dans le menu Outils. Lorsque vous réglez cette
option sur Dual l ll, le mode sonore actuel est afché à l’écran.
Type de programme
Indication à l'écran
Indication à l’écran
NICAM
stéréo
Programme normal
(Audio standard)
Mono (Usage normal)
Normal + Mono NICAMNICAM
Mono
(Normal)
NICAM Stéréo
NICAM
stéréo
Mono
(Normal)
NICAM DUAL-I/II
NICAM
dual 1
NICAM
dual
2
Mono
(Normal)
A2
stéréo
Programme normal
(Audio standard)
Mono (Usage normal)
Bilingue ou DUAL-I/IIDual I
Dual II
StéréoStéréo
Mono
(Mono forcé)
Si le signal stéréo est faible et qu’une permutation automatique se produit, passez alors en Mono.
Cette fonction n’est activée qu’en son stéréo. Elle est désactivée en mode mono.
Cette fonction n’est disponible qu’en mode TV.
N
N
N
Volume auto → Arrêt / Marche
Chaque station de télédiffusion possède ses propres conditions de signal et
il n’est donc pas facile de régler le volume chaque fois que vous changez de
chaîne. Cette fonction vous permet de régler automatiquement le volume du
canal désiré en réduisant la puissance sonore lorsque le signal de modulation
est élevé ou en augmentant la puissance sonore lorsque le signal de modulation
est faible.
Sélection Haut-parleur → Haut-parleur externe/Haut-parleur TV
Pour entendre le son par l’intermédiaire d’enceintes séparées, désactivez l’
amplicateur interne.
Les boutons –
+, MUTE ne fonctionnent pas lorsque la fonction Haut-parleur TV est réglée sur Arrêt.
Si vous sélectionnez Haut-parleur externe dans le menu Haut-parleur externe, les paramètres de son sont limités.
Haut-parleurs internes du téléviseurSortie audio (Optique, Sortie G/D) vers système audio
TV / Ext. / AV / S-Video / Component / PC / HDMITV / Ext. / AV / S-Video / Component / PC / HDMI
Haut-parleur TVSortie enceinteSortie son
Haut-parleur externeSilenceSortie son
Absence de signal vidéoSilenceSilence
Sélection du son
Lorsque la fonction PIP est activée, vous pouvez écouter le son accompagnant l’image secondaire.
Principal
: pour écouter le son accompagnant l’image principale.
Secondaire: pour écouter le son accompagnant l’image secondaire.
Appuyez sur le bouton TOOLS pour afcher le menu Outils.
Vous pouvez également dénir le son de l’image secondaire en sélectionnant Outils → PIP →
Sélection du son.
Réinitialisation du son
Réinitial. tout / Réinitial. mode son / Annuler: Vous pouvez ramener tous les réglages mémorisés à leur valeur par défaut.
❑
❑
N
N
❑
T
❑
Sélection Haut-parleur : Haut-parleur TV
Sélection du son : Principal
Réinitialisation du son
►
Son
Outils
Anynet+ (HDMI-CEC)
Format de l'image : Larg. auto
Image Mode : Standard
Son Mode : Personnel
Veille : Arrêt
SRS TS XT : Arrêt
Mode éco. : Arrêt
Dual l ll ◄ Mono ►
U
Déplacer L Régler e Quitter
Page 86
Français - 23
Utilisation du menu Setup
Langue
Vous pouvez sélectionner la langue des menus.
Verrouillage Canal→ Arrêt / Marche
Cette fonction permet d’empêcher que des utilisateurs non autorisés, tels que
des enfants, regardent des programmes inappropriés, en désactivant la vidéo et
l’audio.
Avant que l’écran de conguration s’afche, l’écran de saisie du code PIN
apparaît. Entrez votre code PIN à quatre chiffres.
Le code PIN par défaut d’un nouveau téléviseur est 0-0-0-0. Vous pouvez
modier le code PIN en sélectionnant Modier PIN dans le menu.
Vous pouvez verrouiller certaines chaînes dans la liste des chaînes. (reportez-vous à la page
14)
Verrouillage Canal est uniquement disponible en mode TV.
Modier PIN
Vous pouvez changer le code personnel demandé pour pouvoir congurer le téléviseur.
Avant que l’écran de conguration s’afche, l’écran de saisie du code PIN apparaît. Entrez votre code PIN à quatre
chiffres.
Le code PIN par défaut d’un nouveau téléviseur est 0-0-0-0.
Si vous avez oublié le code, appuyez sur les boutons de la télécommande dans l’ordre suivant, ce qui remet le code à
0-0-0-0: POWER (Arrêt), MUTE, 8, 2, 4, POWER (Marche).
Verrouillage parental → Classement parental
Cette fonction permet d’empêcher certains utilisateurs, par exemple des enfants, de regarder des émissions inappropriées, en
les protégeant à l’aide d’un code de 4 chiffres déni par l’utilisateur.
Dans l’écran Classement parental, congurez la signalétique.
Avant que l’écran de conguration s’afche, l’écran de saisie du code PIN apparaît. Entrez votre code PIN à quatre
chiffres.
Le code PIN par défaut d’un nouveau téléviseur est 0-0-0-0. Vous pouvez modier le code PIN en sélectionnant Modier
PIN dans le menu.
Une fois la signalétique dénie, le symbole
\
s’afche.
Autor.tout: est uniquement disponible en mode TV.
Bloq. tout: n’est pas disponible lorsque le mode PIP est activé.
Sous-titres
Vous pouvez activer ou désactiver la fonction sous-titres. Utilisez ce menu pour congurer le mode des sous-titres. Normal
sélectionne les sous-titres de base ; Malentendants sélectionne les sous-titres pour personnes malentendantes.
Sous-titres → Arrêt / Marche: Active ou désactive les sous-titres.
Mode → Normal / Malentendants: Configure le mode des sous-titres.
Langue des sous-titres: Configure la langue des sous-titres.
Si le programme visionné n’offre pas de fonction Malentendants, le mode Normal est automatiquement activé même si le
mode Malentendants est sélectionné.
L’anglais est la langue par défaut si la langue sélectionnée n’est pas disponible.
Vous pouvez sélectionner ces options en appuyant sur le bouton SUBT. de la télécommande.
Langue du télétexte
Vous pouvez dénir la langue du télétexte en sélectionnant le type de langue.
L’anglais est la langue par défaut si la langue sélectionnée n’est pas
disponible.
Première Langue Audio/Deuxième Langue Audio/Langue princ. sous-titres/Langue sec. sous-titres/Première Langue
Télétexte/Deuxième Langue Télétexte
Cette fonction permet de sélectionner une des langues disponibles. La langue sélectionnée ici est la Langue par défaut
lorsque l’utilisateur sélectionne un canal.
Si vous changez la langue, les options Langue des sous-titres, Langue audio et Langue du télétexte du menu Langue sont
automatiquement modiées en conséquence.
Les options Langue des sous-titres, Langue audio et Langue du télétexte du menu Langue présentent une liste des languaes
prises en charge par la chaîne actuelle et la langue sélectionnée est mise en surbrillance. Si vous modiez le réglage des
langues, la nouvelle sélection n’est valable que pour le canal actuel. Le nouveau réglage n’affecte pas la langue des soustitres principale, la langue audio principale ni la langue télétexte principale sélectionnées dans le menu de préférences.
Texte numérique → Désactiver / Active
Si le programme est diffusé avec du texte numérique, cette fonction est activée.
MHEG (Multimedia and Hypermedia Information Coding Experts
Group)
Norme internationale pour les systèmes de codage des données utilisés avec
le multimédia et l’hypermédia. Niveau supérieur à celui du système MPEG, qui
inclut de l’hypermédia à liaison de données tel que des images xes, le service
de caractères, l’animation, les chiers graphiques et vidéo et les données
multimédia. MHEG est une technologie utilisateur d’interaction de durée
d’utilisation appliquée à divers domaines, dont la vidéo à la demande (VOD),
la télévision interactive (ITV), le commerce électronique, la téléformation, la
téléconférence, les bibliothèques numériques et les jeux en réseau.
Effet lumineux → Arrêt / En veille/En marche/Toujours
Vous pouvez allumer/éteindre la LED bleue à l'avant de votre téléviseur en fonction de la situation. Recourez à cette fonction
pour économiser de l'énergie ou lorsque la LED fatigue vos yeux.
Arrêt: TLa LED bleue est toujours éteinte.
En veille: La LED bleue est allumée en mode veille et éteinte quand le téléviseur est sous tension.
En marche: La LED bleue est allumée quand vous regardez la télévision et éteinte quand le téléviseur est hors tension.
Toujours: La LED bleue est toujours allumée.
Réglez la fonction Effet lumineux sur Arrêt pour réduire la consommation électrique.
Mélodie
Arrêt
/ Bas / Moyen / Elevé
La mélodie de mise sous/hors tension du téléviseur peut être ajustée.
Aucune mélodie n’est lue dans les cas suivants:
Aucun son n’est émis par le téléviseur car le bouton MUTE a été enfoncé.
Aucun son n'est émis par le téléviseur car le bouton –
(Volume) a été enfoncé.
Lorsque le téléviseur est éteint par la fonction Veille.
Divertissement
Le mode Divertissement permet de sélectionner les valeurs d’afchage et de son optimales pour le sport, le cinéma et les
jeux.
Arrêt: désactive la fonction Divertissement.
Sports: fournit une qualité d’image et de son optimale pour le sport.
Cinéma: fournit une qualité d’image et de son optimale pour regarder un film. Vous pouvez profiter d’une image plus belle et
d’un son encore meilleur.
Jeu: fournit une qualité d’image et de son optimale pour les jeux. Ce mode accélère la vitesse de lecture lorsqu’une console
de jeu est connectée au téléviseur.
Si vous activez l’un des trois modes Divertissement, les paramètres seront verrouillés, empêchant toute modication. Les
réglages de mode d’image et de mode audio sont en outre indisponibles. Si vous souhaitez régler les mode d’image et audio,
le mode Divertissement doit être désactivé.
Les réglages du mode Divertissement sont enregistrés séparément pour chaque source d’entrée.
Le mode Divertissement n'est pas activé en mode PC.
Vous pouvez appuyer plusieurs fois sur le bouton E.MODE de la télécommande
pour modier le paramètre Divertissement.
❑
❑
N
❑
N
❑
N
-
-
-
❑
N
N
N
O
Conguration
Langue du télétexte : ----
Préférence
Texte numérique : Activer ►
Effet lumineux : LED act. marche
Ajustement fixation murale
Mélodie
: Arrêt
Divertissement : Arrêt
Mode éco. : Arrêt
PIP
Mise à niveau du logiciel
Page 88
Français - 25
Mode éco.
Cette fonction règle la luminosité du téléviseur an de réduire la consommation d’énergie. Lorsque vous regardez la
télévision le soir, réglez l’option du mode Mode éco. sur Elevé pour reposer vos yeux et réduire la consommation d’énergie.
Arrêt: Désactive la fonction d’économie d’énergie.
Bas: Met le téléviseur en mode d’économie d’énergie basse.
Moyen: Met le téléviseur en mode d’économie d’énergie moyenne.
Elevé: Met le téléviseur en mode d’économie d’énergie élevée.
Appuyez sur le bouton TOOLS pour afcher le menu Outils.
Vous pouvez également dénir l’option d’économie d’énergie en sélectionnant Outils → Mode éco..
Mise à niveau du logiciel
Pour garder le produit à jour avec les options Digital Television, les mises à jour
logiciel sont régulièrement diffusées dans le signal télévision normal. Le téléviseur
détecte automatiquement ces signaux et afche le bandeau de mise à jour logiciel.
Vous avez le choix d’installer ou non la mise à jour.
USB
Insérez dans le téléviseur un lecteur USB contenant la mise à niveau du
microprogramme. Veillez à ne pas couper l’alimentation ni retirer le lecteur
USB pendant l’application des mises à niveau. Une fois la mise à niveau du
micrologiciel terminée, le téléviseur se met automatiquement hors puis sous
tension. Vériez la version du micrologiciel une fois les mises à niveau terminées.
Lorsque le logiciel est mis à niveau, les paramètres vidéo et audio dénis reprennent leur valeur par défaut (d’usine). Nous
vous recommandons de noter vos réglages pour les rétablir facilement après la mise à niveau.
Canal
Met à niveau le logiciel en utilisant le signal diffusé.
Mise à niveau en mode Veille
Pour poursuivre la mise à jour du logiciel en gardant le téléviseur sous tension, sélectionnez Marche (Actif) en appuyant sur
le bouton ▲ ou ▼. 45 minutes après que le mode veille a été activé, une mise à jour manuelle est réalisée automatiquement.
Etant donné que le courant est activé de façon interne, l'écran peut s'allumer brièvement pour le produit. Le phénomène peut
se poursuivre durant une heure jusqu’à ce que la mise à jour logiciel soit terminée.
Autre logiciel
Afche des informations sur la version du logiciel.
Interface commune
Installation de la carte d’interface commune (CI)
a. Achetez le module CI CAM en vous rendant chez le revendeur le plus proche
ou par téléphone.
b. Insérez la CI CARD dans la CAM dans la direction indiquée par la èche
jusqu'à ce qu'elle soit emboîtée.
c. érez la CAM avec la CI CARD installée dans la fente de l'interface commune.
Insérez la CAM dans la direction indiquée par la èche, juste au-dessus de
l'extrémité, pour qu'elle soit parallèle à la fente.
d. Vériez si une image est visible sur un canal à signal brouillé
Menu CI
Cela aide l’utilisateur à sélectionner un élément du menu pris en charge par CAM.
Sélectionnez le menu CI dans le menu PC Card.
Infos sur l’application
Contient des informations relatives à la CAM insérée dans la fente CI et les
afche.
Les Application Info concernent la CI CARD. Vous pouvez installer la CAM que le téléviseur soit allumé ou éteint.
1. Achetez le module CI CAM en vous rendant chez le revendeur le plus proche ou
par téléphone.
2. Insérez la CI CARD dans la CAM dans la direction indiquée par la èche jusqu’à ce qu’elle soit emboîtée.
3. Insérez la CAM avec la CI CARD installée dans la fente de l’interface commune.
(Insérez la CAM dans la direction indiquée
par la èche, juste au-dessus de l’extrémité pour qu’elle soit parallèle à la fente.)
4. Vériez si une image est visible sur un canal à signal brouillé.
❑
T
❑
❑
N
4
Lecteur USB
PPanneau latéral du
téléviseur
Page 89
Français - 26
Réglage de l’heure
Horloge
Le réglage de l’horloge est nécessaire pour utiliser les différentes fonctions de
la minuterie de la télévision.
L’heure actuelle s’afche à chaque fois que vous appuyez sur le bouton
INFO.
Si vous débranchez le cordon d’alimentation, vous devrez régler à nouveau
l’horloge.
Mode Horloge
Vous pouvez dénir l’heure actuelle manuellement ou automatiquement.
Auto.: Règle automatiquement l’heure en fonction de signaux diffusés.
Manuel: Permet de régler l’heure manuellement.
Réglage. Horloge
Vous pouvez dénir l’heure actuelle.
Sélectionnez cette option lorsque Mode Horloge est à Manuel.
Vous pouvez régler directement le mois, le jour, les heures et les minutes en
appuyant sur les boutons numériques de la télécommande.
Veille → Arrêt / 30 min. / 60 min. / 90 min. / 120 min. / 150 min. /
180 min.
La minuterie de mise en veille coupe automatiquement la télévision après une
durée préréglée (30, 60, 90, 120, 150 ou 180 minutes).
Le téléviseur passe automatiquement en mode veille lorsque le minuteur atteint 0.
Pour annuler la fonction Veille, sélectionnez Arrêt.
Appuyez sur le bouton TOOLS pour afcher le menu Outils.
Vous pouvez également dénir la minuterie de veille d’image en sélectionnant Outils → Veille.
Minuteur 1 / Minuteur 2 / Minuteur 3
Trois réglages différents de mise en marche/arrêt peuvent être dénis.
Période d'activation:
Sélectionnez les heures et les minutes et l’action activer/désactiver.
(Pour activer le minuteur selon les réglages dénis, choisissez Activer.)
Période de désactivation:
Sélectionnez les heures et les minutes et l’action activer/désactiver.
(Pour activer le minuteur selon les réglages dénis, choisissez Activer.)
Volume:
Sélectionnez le niveau de volume désiré.
Contenu:
Lorsque la fonction
Période d'activation
est active, vous pouvez activer un canal spécique ou lire un contenu
spécique tel qu’une photo ou des chiers audio.
TV / USB: Sélectionnez TV ou USB. (Assurez-vous que le périphérique USB est branché sur le téléviseur.)
Antenne: Sélectionnez ATV ou DTV.
Canal: Sélectionnez la chaîne désirée.
Musique: Sélectionnez le dossier contenant des chiers MP3 sur le périphérique USB.
Photo: Sélectionnez le dossier contenant des chiers JPEG sur le périphérique USB.
Répétition:
Sélectionnez Une fois, Ts jours, Lun - Ven, Lun - Sam, Sam - Dim ou Manuel.
Lorsque Manuel est sélectionné, appuyez sur le bouton ► pour sélectionner le jour de la semaine.
Appuyez sur le bouton
ENTER
E
sur le jour de votre choix. Le symbole c apparaît alors.
Vous devez préalablement régler l’horloge.
Vous pouvez régler les heures, les minutes et les chaînes directement à l’aide du pavé numérique de la télécommande.
Mise hors tension automatique
Lorsque vous dénissez la minuterie sur On, le téléviseur s’éteint si aucune commande n’est activée dans les 3 heures qui
suivent la mise sous tension. Cette fonction est disponible uniquement lorsque la minuterie est dénie sur On ; elle permet
d’éviter toute surchauffe occasionnée par une utilisation prolongée du téléviseur.
❑
N
N
•
•
N
N
❑
N
N
T
❑
•
•
•
•
•
N
N
N
N
Conguration
Plug & Play
Langue : Français
Horloge ►
Sélection du réseau : Câble
Configuration du réseau sans fil
Les paragraphes qui suivent décrivent les procédures à suivre pour congurer le réseau avec le protocole DHCP (Dynamic
Host Conguration Protocol). Étant donné qu’une adresse IP, un masque de sous-réseau, une passerelle et un serveur DNS
sont automatiquement attribués lorsque DHCP est sélectionné, vous ne devez pas les spécier manuellement.
1. Raccordez le port [LAN] à l’arrière du téléviseur et le modem externe à l’aide d’un câble LAN.
2. Raccordez le connecteur LAN mural et le modem externe à l’aide d’un câble modem.
Les connecteurs (position et type de port) de l’appareil externe peuvent varier selon le fabricant.
Si l’allocation de l’adresse IP par le serveur DHCP échoue, éteignez le modem externe, rallumez-le après au moins 10
secondes et réessayez.
Pour les raccordements entre le modem externe et le routeur (Sharer), reportez-vous à la documentation du produit
correspondant.
Vous pouvez connecter le téléviseur directement au réseau sans passer par un routeur.
Vous ne pouvez pas utiliser un modem ADSL à connexion manuelle, car celui-ci ne prend pas en charge DHCP. Vous devez
utiliser un modem ADSL à connexion automatique.
N
N
N
N
N
Panneau arrière du téléviseur
Connecteur
modem mural
Câble modem
2
Modem externe (ADSL /
VDSL / Cable TV)
Câble LAN
1
Selon votre réseau, vous pouvez raccorder directement le connecteur LAN et le téléviseur.
Panneau arrière du téléviseur
Câble LAN
Connecteur
modem mural
Vous pouvez connecter le réseau via un routeur.
Panneau arrière du téléviseur
Connecteur
modem mural
Modem externe (ADSL /
VDSL / Cable TV)
Routeur IP
Câble LAN
Câble modem
Câble LAN
Page 91
Français - 28
Connexion LAN pour un environnement IP statique
Les paragraphes qui suivent décrivent les procédures à suivre pour congurer le réseau avec une adresse IP statique. Vous
devez entrer manuellement l’adresse IP, le masque de sous-réseau, la passerelle et le serveur DNS de votre fournisseur d’accès.
1. Raccordez le port [LAN] à l’arrière du téléviseur et le connecteur LAN à l’aide d’un câble LAN.
Les connecteurs (position et type de port) de l’appareil externe peuvent varier selon le fabricant.
Si vous utilisez une adresse IP statique, votre fournisseur d’accès vous communiquera l’adresse IP, le masque de sous-
réseau, la passerelle et le serveur DNS appropriés. Vous devez entrer ces valeurs pour effectuer la conguration réseau.
Si vous ne connaissez pas ces valeurs, consultez votre administrateur de réseau.
Pour la conguration et le raccordement d’un routeur (Sharer), reportez-vous à la documentation du produit
correspondant.
Vous pouvez connecter le téléviseur directement au réseau sans passer par un routeur.
Si vous utilisez un routeur IP prenant en charge le protocole DHCP, vous pouvez congurer l’appareil comme utilisant
DHCP ou une adresse IP statique.
Pour les procédures à suivre si vous utilisez une adresse IP statique, consultez votre fournisseur d’accès.
Connexion réseau - Sans l
Vous pouvez vous connecter au réseau sans l au travers d’un routeur IP sans l.
1. Branchez ‘Samsung Wireless LAN Adapter’ sur le connecteur Wiselink du téléviseur.
Vous devez employer ‘Samsung Wireless LAN Adapter’(WIS-08BG) pour utiliser un réseau sans l.
L’adaptateur ‘Samsung Wireless LAN Adapter’ est vendu séparément. Pour vous le procurer, contactez un agent ou un
centre de services Samsung Electronics.
Pour utiliser un réseau sans l, vous devez connecter le téléviseur à un routeur IP sans l.
Si ce routeur prend en charge le protocole DHCP, le téléviseur peut utiliser DHCP ou une adresse IP statique pour se
connecter au réseau sans l.
Vous devez utiliser un routeur IP sans l prenant en charge IEEE 802.11 B ou IEEE 802.11G.
Si le routeur IP sans l vous permet de désactiver/activer la fonction de connexion Ping, activez-la.
Réglez le routeur IP sans l en mode Infrastructure. Le mode Ad-hoc n’est pas pris en charge.
Sélectionnez un canal inutilisé pour le routeur IP sans l. Si le canal affecté au routeur IP sans l est actuellement utilisé
par un autre périphérique dans le voisinage, il y aura des interférences et la communication peut échouer.
Pour la clé de sécurité du routeur IP, les options suivantes sont obligatoires.
1) Authentication Mode : WEP, WPAPSK, WPA2PSK
2) Encryption Type : WEP, TKIP, AES
SI vous utilisez d’autres paramètres, le routeur ne fonctionnera pas avec le téléviseur.
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
Panneau arrière du téléviseur
Câble LAN
1
Connecteur LAN
mural
Panneau arrière du téléviseur
Câble LAN
Routeur IP
Câble LAN
Connecteur LAN
mural
Vous pouvez connecter le réseau via un routeur.
Panneau latéral du téléviseur
Adaptateur "Samsung
Wireless LAN Adapter "
Câble LAN
Routeur IP sans l
Connecteur LAN
mural
Page 92
Français - 29
Configuration du réseau
Sélection du réseau
Sélectionnez Cable ou Wireless, selon la méthode utiliser pour la connexion au
réseau.
Le menu n’est disponible que si ‘Samsung Wireless LAN Adapter’ est
connecté.
Câble
: Connexion au réseau par câble.
Sans fil
: Connexion sans l.
Conguration internet
Conf. Prot. Internet → Config. auto. / Config. Manuel
Test réseau
: Permet de tester ou vérier la connexion réseau après la conguration du réseau.
En cas d’impossibilité de se connecter à un réseau câblé
Si votre fournisseur d’accès a enregistré l’adresse MAC du périphérique utilisé pour se connecter la première fois à
Internet et qu’il authentie cette adresse MAC chaque fois que vous vous connectez à Internet, votre téléviseur ne
pourra pas se connecter à Internet car l’adresse MAC différera de celle du périphérique (votre PC) utilisé pour se
connecter la première fois. Dans ce cas, demandez à votre fournisseur d’accès la procédure à suivre pour connecter des
périphériques autres que votre PC (p. ex. votre téléviseur) à Internet. Si votre fournisseur d’accès exige un identiant ou
un mot de passe pour la connexion à Internet (réseau), votre téléviseur ne pourra pas se connecter à Internet. Dans ce
cas, vous devez entrer l’identiant ou le mot de passe lors de la connexion à Internet à l’aide d’un routeur
.
La connexion à Internet peut échouer à cause d’un problème de pare-feu (rewall). Dans ce cas, contactez votre
fournisseur d’accès. Si vous ne pouvez pas vous connecter à Internet même en suivant les procédures communiquées
par votre fournisseur d’accès, consultez un Centre de services Samsung Electronics.
Conguration du réseau sans l
Conf. Prot. Internet → Config. auto. / Config. Manuel
Test réseau
: Permet de tester ou vérifier la connexion réseau après la configuration du réseau.
En cas d’impossibilité de se connecter à un réseau sans l
Il se peut que votre téléviseur ne parvienne pas à localiser un point d’accès conguré comme SSID privé. Dans ce cas,
modiez les paramètres de point d’accès et réessayez. Si votre fournisseur d’accès a enregistré l’adresse MAC du
périphérique utilisé pour se connecter la première fois à Internet et qu’il authentie cette adresse MAC chaque fois que
vous vous connectez à Internet, votre téléviseur ne pourra pas se connecter à Internet car l’adresse MAC différera de
celle du périphérique (votre PC) utilisé pour se connecter la première fois. Dans ce cas, demandez à votre fournisseur
d’accès la procédure à suivre pour connecter des périphériques autres que votre PC (p. ex. votre téléviseur) à Internet.
Si vous ne pouvez pas vous connecter à Internet même en suivant les procédures communiquées par votre fournisseur
d’accès, consultez un Centre de services Samsung Electronics.
Sélec. Point accés:
Vous pouvez sélectionner le routeur à utiliser pour la connexion au réseau sans l.
Si la liste de points d’accès ne comporte pas de point d’accès sans l, appuyez sur le bouton Rouge.
Une fois la connexion effectuée, l’écran initial réapparaît.
Si vous avez sélectionné un point d’accès qui exige une authentication, entrez la clé de sécurité.
Si vous avez sélectionné un point d’accès exigeant une authentication :
L’écran de saisie de la clé de sécurité apparaît.
Entrez la clé de sécurité et appuyez sur le bouton ENTERE.
Utilisez les touches de la télécommande dans l’écran de saisie de la clé de sécurité.
L'écran de conguration peut varier en fonction des types de sécurité.
BoutonDescription
▲/▼/◄/►,
(cercle)
Déplace la sélection vers le haut/le bas/la gauche/la droite.
(ENTER)
Entre le caractère sélectionné.
Bouton rouge
Permet de basculer entre majuscules et minuscules.
Bouton vert
Permet d'effacer un caractère déjà introduit.
Bouton bleu
Permet de mettre n à la saisie de la clé de sécurité.
Si vous connectez un câble réseau et que le réseau prend en charge DHCP, les paramètres IP (Internet Protocol) sont congurés
automatiquement. Vériez si le câble LAN est correctement branché. (Voir page 27)
1.
Réglez Sélection du réseau sur Câble.
2
. Sélectionnez Conguration internet.
3.
Réglez Cong. prot. Internett sur Cong. auto..
4.
Sélectionnez Test réseau pour vérier la connexion au réseau.
Conguration internet - Cong. man.
Pour connecter le téléviseur au réseau en utilisant une adresse IP statique, vous devez congurer les paramètres IP (Internet
Protocol). Vériez si le câble LAN est correctement branché. (Voir page 27)
1. Réglez Sélection du réseau sur Câble.
2
. Sélectionnez Conguration internet.
3.
Réglez Cong. prot. Internet sur Cong. man..
4.
Congurez les paramètres Adresse IP, Masque de sous-réseau, Passerelle et Serveur DNS.
Appuyez sur les boutons numériques de la télécommande lorsque vous paramétrez le réseau manuellement.
5.
Sélectionnez Test réseau pour vérier la connexion au réseau.
Conguration du réseau sans l - Cong. auto.
Le menu n’est disponible que si ‘Samsung Wireless LAN Adapter’ est connecté. (Voir page 28)
Si vous connectez un câble réseau et que le réseau prend en charge DHCP, les paramètres IP
(Internet Protocol) sont congurés
automatiquement. Le routeur sans l à connecter à ce produit doit prendre en charge DHCP.
1.
Réglez Sélection du réseau sur Sans l.
2
. Sélectionnez Conguration du réseau sans l.
3.
Réglez Cong. prot. Internet sur Cong. auto..
4.
Sélectionnez un point d’accès via Sélec. Point accés.
5.
Sélectionnez Test réseau pour vérier la connexion au réseau.
Conguration du réseau sans l - Cong. man.
Le menu n’est disponible que si ‘Samsung Wireless LAN Adapter’ est connecté. (Voir page 28)
1.
Réglez Sélection du réseau sur Sans l.
2
. Sélectionnez Conguration du réseau sans l.
3.
Réglez Cong. prot. Internett sur Cong. man..
4.
Sélectionnez un point d’accès via Sélec. Point accés.
5.
Sélectionnez Test réseau pour vérier la connexion au réseau.
N
Page 94
Français - 31
Liste Source / Modif. Nom
Liste Source
Permet de sélectionner le téléviseur ou d’autres sources d’entrée externes
comme les lecteurs DVD ou les décodeurs câble/récepteurs satellite (boîtiers
décodeurs) connectés au téléviseur. Permet de sélectionner la source d’entrée
de votre choix.
Vous ne pouvez sélectionner que les appareils externes connectés au
téléviseur. Dans Liste Source, les entrées connectées sont mises en
surbrillance et afchés en début de liste. Les entrées non connectées
apparaissent dans le bas de la liste.
Utilisation des boutons de couleur de la télécommande dans la liste
des sources
Rouge (Refresh): Actualise la liste des unités externes se connectant.
TOOLS (Option): Afche les menus Modif. Nom et Information.
Appuyez sur le bouton SOURCE de la télécommande pour afcher une
source de signal externe. Le Mode TV peut être sélectionné en appuyant
sur le bouton TV, les boutons numériques (0-
9) et le bouton P < / > de la
télécommande.
Modif. Nom
Magnétoscope / DVD / Décodeur Câble / Décodeur satellite / Décodeur PVR / Récepteur AV / Jeu / Caméscope / PC /
TV / IPTV / Blu-Ray / HD DVD / DMA
Nommez le périphérique connecté aux prises d’entrée pour rendre la sélection des sources d’entrée plus facile.
Lorsqu’un PC d’une résolution de 1 920 x 1 080 à 60 Hz est branché sur le port HDMI IN2, vous devez régler le mode
HDMI
2/DVI sur PC dans Modif. Nom du mode Entrée.
❑
N
N
-
-
O
❑
N
Liste Source
Modif. Nom
Entrée
Guide Produit
Le Guide de produit vous donne des informations sur les fonctions les plus
importantes de ce téléviseur.
1.
Appuyez sur le bouton MENU pour afcher le menu. Appuyez sur le bouton ▲ ou
▼ pour sélectionner Application, puis appuyez sur le bouton ENTER
E
.
2. Appuyez sur le bouton ▲ ou ▼ pour sélectionner Guide Produit, puis appuyez
sur le bouton ENTER
E
.
3. Appuyez sur le bouton ◄ ou ► pour sélectionner un Guide (Picture Quality,
Entertainment ou Connectivity) et appuyez ensuite sur le bouton ENTER
E
.
4. Vous pouvez parcourir l’écran r Guide Produit à l’aide des boutons ◄ et ►.
Picture QualityFull HD 1080p
Ultra FilterBright
Real 100Hz(50") / 100Hz Dual Scan(63")
EntertainmentContent Library
Entertainment Mode
ConnectivityWISELINK Pro
DLNA
4HDMI
Anynet+
5.
Appuyez sur le bouton EXIT pour quitter le menu.
Application
Anynet+ (HDMI-CEC)
Content Library
Guide Produit ►
Page 95
Français - 32
Utilisation de la télécommande dans le menu Guide Produit
BoutonDescription
Bouton jauneAfche le contenu du menu Guide Produit dans l’ordre. (Exécution automatique)
▲/▼/◄/►
(cercle)
Déplace le curseur et sélectionne un élément.
ENTER
E
Valide l’élément actuellement sélectionné.
RETURNRevient au menu précédent.
EXITArrête la fonction en cours et revient au menu principal Guide Produit.
P
, PRE-CH
Arrête le mode Product Guide et revient au mode TV.
WISELINK Pro
Connexion d’un périphérique USB
1. Appuyez sur le bouton POWER pour allumer le téléviseur.
2. Connectez un périphérique USB contenant des chiers photo, musicaux et/ou
lm à la prise WISELINK Pro (prise USB) située sur le côté du téléviseur.
Si vous entrez dans le mode WISELINK Pro alors qu’aucun périphérique
USB n’est connecté, le message “Auc. app. branché. Vérier branchement.”
s’afche. Dans ce cas, insérez le périphérique USB, quittez l’écran en appuyant
sur le bouton W.LINK de la télécommande et entrez de nouveau dans l’écran
WISELINK Pro.
Le protocole MTP (Media Transfer Protocol) n’est pas pris en charge.
Le système de chiers ne prend en charge que le format FAT16/32 (le système de chiers NTFS n’est pas pris en charge).
Il est possible que certains types d’appareils photo numériques et de périphériques audio USB ne soient pas compatibles
avec ce téléviseur.
WISELINK Pro ne prend en charge que les périphériques de stockage de masse USB de la classe MSC. La classe de
stockage de masse MSC est dédiée aux périphériques de transport de masse uniquement. Il s’agit notamment des clés USB
et des lecteurs de cartes Flash (les concentrateurs et les disques durs USB ne sont pas pris en charge).
Connectez-vous directement au port USB de votre téléviseur. Si vous utilisez une connexion par câble séparée, un problème
de compatibilité USB risque de se poser.
Avant de connecter l’appareil au téléviseur, sauvegardez vos chiers an d’éviter qu’ils ne soient endommagés ou que des
données ne soient perdues. SAMSUNG ne saurait, en aucun cas, être tenu responsable de la perte de données ou de
l’endommagement d’un chier de données.
Ne déconnectez pas le périphérique USB en cours de chargement.
MSC prend en charge les chiers MP3 et JPEG, alors qu’un périphérique PTP prend uniquement en charge les chiers JPEG.
Le format JPEG séquentiel est pris en charge.
Plus la résolution de l’image est élevée, plus le temps d’afchage à l’écran sera long.
La résolution JPEG maximale prise en charge est 15
360 x 8 640 pixels.
Pour les chiers non pris en charge ou endommagés, le message Format chier non compatible s’afche.
Si le nombre de chiers photo est supérieur à 4
000 (ou à 3 000 dans le cas des chiers musicaux), il se peut que les chiers
situés au-delà de cette limite ne soient pas afchés dans la Liste des photos (ou dans la Liste musicale).
Les chiers MP3 avec gestion des droits numériques (DRM) téléchargés à partir d’un site payant ne peuvent pas être lus.
La technologie DRM (Gestion des droits numériques) prend en charge la création de contenu, la distribution et la gestion
intégrales du contenu (par exemple, la protection des droits et des intérêts des fournisseurs de contenu, la prévention de la
copie illégale du contenu), ainsi que la gestion de la facturation et des règlements.
Si vous passez à une photo, son chargement peut prendre quelques secondes. A ce stade, l’icône de chargement apparaît.
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
4
Panneau latéral du
téléviseur
Lecteur USB
Page 96
Français - 33
Utilisation de la fonction WISELINK Pro
Cette fonction vous permet de lire des photos, de la musique et/ou des lms enregistrés sur un périphérique de stockage de
masse USB (MSC).
Accès au menu WISELINK Pro
1. Appuyez sur le bouton MENU. Appuyez sur le bouton ▲ ou ▼ pour sélectionner Application, puis appuyez sur le bouton ENTERE.
2. Appuyez sur le bouton ▲ ou ▼ pour sélectionner WISELINK Pro, puis appuyez sur le bouton ENTER
E
.
Le menu WISELINK Pro s’afche.
Appuyez sur le bouton W.LINK de la télécommande pour afcher le menu
WISELINK Pro.
Appuyez plusieurs fois sur le bouton SOURCE de la télécommande pour
sélectionner USB ou DLNA, puis appuyez sur le bouton ENTER
E
.
3. Appuyez sur le bouton rouge, puis sur le bouton ▲ ou ▼ pour sélectionner
l’unité de stockage USB correspondante (si elle est connectée par le biais d’un
concentrateur). Appuyez sur le bouton ENTER
E
.
Cette fonction diffère selon l’unité de stockage USB connectée au
téléviseur.
Le nom du périphérique USB sélectionné s’afche dans le coin inférieur
gauche de l’écran.
4.
Appuyez sur le bouton ◄ ou ► pour sélectionner une icône (Photo, Music,
Movie, Setup), puis appuyez sur le bouton ENTER
E
. Pour quitter le mode
WISELINK Pro, appuyez sur le bouton W.LINK de la télécommande.
Les jeux vidéo sont pris en charge (pas de programmes de jeu).
Retrait d’une unité de stockage USB en toute sécurité
Vous pouvez retirer le périphérique du téléviseur en toute sécurité.
1.Appuyez sur le bouton TOOLS dans l'écran de la liste des chiers WISELINK
Pro ou pendant la lecture d'un chier musical ou d'un diaporama.
2
. Appuyez sur le bouton ▲ ou ▼ pour sélectionner Retrait sécurisé, puis
Lire gp act.
Supprimer
Information
Retrait sécurisé
Page 97
Français - 34
Afchage
1. Fichier sélectionné: le chier actuellement sélectionné est mis en surbrillance. Les chiers photo et lm sont afchés sous la
forme de miniatures.
2. Fenêtre d’informations: afche des informations sur le chier actuellement sélectionné. Il existe une fenêtre d’informations
distincte destinée uniquement aux chiers photo et lm. Dans le cas des chiers musicaux, les informations apparaissent
également à l’endroit où sont afchés les chiers.
3.
Ordre de tri actuel: ce champ afche l’ordre de tri actuel des chiers. Appuyez su
r le bouton ▲ ou ▼ pour modier l’ordre de
tri des chiers.
4. Groupes: afche les groupes de tri. Le groupe de tri contenant la photo actuellement sélectionnée est mis en surbrillance.
5.
Périphérique actuel: indique le nom du périphérique actuellement sélectionné. Appuyez sur le bouton rouge pour sélectionner
un périphérique.
6
. Informations de sélection: indique le nombre de photos sélectionnées en appuyant sur le bouton Jaune.
7
. Options d’aide
Bouton Rouge (Périph.): sélectionne un appareil connecté.
Bouton Vert (Favoris): modie le réglage des favoris pour le chier sélectionné. Appuyez plus
ieurs fois sur ce bouton
jusqu’à ce que la valeur voulue apparaisse.
Bouton Jaune (Sélection): sélectionne le chier dans la liste. Les chiers musicaux sélectionnés sont marqués du
symbole c. Appuyez une nouvelle fois sur le bouton jaune pour annuler la sélection d’un chier.
Bouton πµ (Passer): passe au groupe de tri précédent / suivant.
Bouton
TOOLS (Option): afche les menus d’options. (Le menu varie en fonction de l’état actuel.)
•
•
•
•
•
Utilisation de la télécommande dans le menu WISELINK Pro
BoutonDescription
▲/▼/◄/►
(cercle)
Déplace le curseur et sélectionne un élément.
ENTER
E
Valide l’élément actuellement sélectionné.
Lors de lecture d’un diaporama, d’un chier musical ou d’un lm :
- Appuyer sur le bouton ENTER
E
pendant la lecture suspend celle-ci.
- Appuyer sur le bouton ENTER
E
en mode Pause relance la lecture.
Lance la lecture d'un diaporama ou d'un chier musical, ou le met en pause.
RETURN
Revient au menu précédent.
TOOLS
Exécute diverses fonctions dans les menus Photo, Musique et Film.
Arrête la lecture du diaporama, du chier musical ou du lm.
Passe au groupe précédent / suivant.
INFO
Afche des informations sur le chier.
W.LINK
Quitte le mode WISELINK Pro.
P
,
PRE-CH
Arrête le mode WISELINK Pro et revient au mode TV.
EXIT
Arrête la fonction en cours et revient au menu principal WISELINK Pro.
Trie les photos par composition. Vous pouvez modier les informations de composition des photos.
Options Compo.:
(horizontal), (vertical), (objet), (perspective), (motif), Non classés.
Do
ssie
r
Trie les photos par dossier. Si le périphérique USB contient de nombreux dossiers, les chiers photo sont afchés dans l’ordre
dans chaque dossier. Le chier photo dans le dossier racine est afché en premier, suivi des autres par ordre alphabétique.
Préférence
Trie les photos par préférence (Favori). Vous pouvez modier les préférences des photos.
Modication du réglage favori
Sélectionnez la photo de votre choix dans la Liste des photos, puis appuyez plusieurs fois sur le bouton vert jusqu’à ce
que le réglage voulu apparaisse.
OptionsFavori:
★ ★ ★, ★ ★ ★, ★ ★ ★, ★ ★ ★
Menu d’options de la Liste des photos
Diaporama
Ce menu vous permet de lire un diaporama à l’aide des chiers photo situés
sur l’unité de stockage USB.
Lire gp act.
Ce menu vous permet de lire un diaporama portant uniquement sur les
chiers photo du groupe de tri sélectionné.
Supprimer
Ce menu vous permet de supprimer les chiers photo sélectionnés.
Changer gp
Vous pouvez modier les informations Couleur et
Compo.
des chiers photo.
Les informations de groupe du chier actuel sont mises à jour et le chier est déplacé vers le nouveau groupe.
Pour modier les informations de plusieurs chiers, sélectionnez ceux de votre choix en appuyant sur le bouton jaune.
Afche des informations sur les chiers photo, dont l’ordre du chier dans le répertoire actuel, le nom, la taille, la résolution, la
date de modication et le chemin d’accès.
Vous pouvez appliquer les mêmes procédures pour afcher les informations des chiers photo pendant un diaporama.
Une autre solution consiste à sélectionner une photo dans la liste et à
appuyer ensuite sur le bouton INFO pour visualiser les informations.
Retrait sécurisé
Vous pouvez retirer le périphérique du téléviseur en toute sécurité.
N
O
Visualisation d’une photo ou d’un diaporama
Visualisation d’un diaporama
1. Appuyez sur le bouton ◄ ou ► pour sélectionner la photo voulue dans la
Liste des photos.
2. Appuyez sur le bouton TOOLS.
3.
Appuyez sur le bouton ▲ ou ▼ pour sélectionner Diaporama, puis appuyez
sur le bouton ENTER
E
.
Tous les chiers contenus dans la liste des photos seront utilisés pour
le diaporama.
Durant le diaporama, les chiers s’afchent dans l’ordre à partir du chier à
l’écran.
Le diaporama progresse dans l’ordre de tri choisi dans la Liste des photos.
Des chiers musicaux peuvent être lus automatiquement pendant le
diaporama, si l’option Fond musical est dénie sur Marche. (V
oir page 37.)
Lorsqu’une liste de photos est afchée, appuyez sur le bouton
∂
(Lecture)/ENTERE de la télécommande pour lancer le diaporama.
Boutons de commande du diaporama
ENTER
E
Lance/Interrompt la lecture du
diaporama.
∫
Permet de quitter le mode diaporama et de revenir
à la liste des photos.
∂
Lance la lecture du diaporama.
TOOLS
Exécute diverses fonctions dans les menus Photo
.
∑
Interrompt la lecture du diaporama.
π/µ
Modie la vitesse de lecture du diaporama.
Lecture du groupe courant
1. Appuyez sur le bouton ▲ ou ▼ pour sélectionner un ordre de tri. (Mois, Date, Couleur, Compo., Dossier, Préférence)
2. Appuyez sur le bouton
π
(Retour arrière) ou µ (Avance rapide) pour sélectionner le groupe de votre choix.
3. Appuyez sur le bouton TOOLS.
4.
Appuyez sur le bouton ▲ ou ▼ pour sélectionner Lire gp act., puis appuyez sur le bouton ENTER
E
.
Seules les photos du groupe contenant les chiers sélectionnés seront utilisées pour le diaporama.
Pour exécuter un diaporama avec uniquement les chiers sélectionnés
1. Appuyez sur le bouton ◄ ou ► pour sélectionner la photo voulue dans la Liste des photos.
2. Appuyez sur le bouton jaune. Répétez l’opération ci-dessus pour sélectionner plusieurs photos.
La marque
c
s’afche à gauche de la photo sélectionnée.
Si vous sélectionnez un seul chier, le diaporama ne s’exécute pas.
Pour désélectionner tous les chiers, appuyez sur le bouton TOOLS et sélectionnez Désélect. tout.
3.
Appuyez sur le bouton
∂
(Lecture)/ENTERE.
Les chiers sélectionnés seront utilisés pour le diaporama.
N
N
N
N
O
N
N
N
N
N
O
SUM
E Pause Préc. Suivant Option Retour
►
Normal20/22 image_1.jpg 440x440 2.0KB 2008/1/1
Page 100
Français - 37
Menu d’options du diaporama
Arrêter le diaporama/Lancer le diaporama
Vous pouvez lancer ou arrêter un diaporama.
Rotat.
Vous pouvez faire pivoter les photos enregistrées sur une unité de stockage
USB.
Chaque fois que vous appuyez sur le bouton ◄, la photo pivote
successivement à 270˚, 180˚, 90˚ et 0˚.
Chaque fois que vous appuyez sur le bouton ►, la photo pivote
successivement à 90˚, 180˚, 270˚ et 0˚.
Zoom
Vous pouvez faire agrandir les photos enregistrées sur une unité de
stockage USB. (x1 → x2 → x4)
Pour déplacer l’image agrandie, appuyez sur le bouton ENTER
E
, puis sur ▲/▼/◄/►. Notez que lorsque la taille de
l’image agrandie est inférieure à celle de l’écran, la fonction de déplacement est inopérante.
Le chier agrandi n’est pas enregistré.
Si vous avez sélectionné Rotat., l'option Zoom est désactivée.
Vit. diaporama
Sélectionnez cette option pour modier la vitesse de délement du diaporama.
Vous ne pouvez sélectionner la vitesse du diaporama que pendant sa diffusion.
Vous pouvez également modier la vitesse du diaporama en appuyant sur la touche
π
(Retour arrière) ou µ (Avance
rapide) pendant la lecture.
Fond musical → Marche / Arrêt
Si vous dénissez Fond musical sur Marche, la musique de fond sera lue lors de l’afchage de photos individuelles ou sous
la forme d’un diaporama.
Si vous dénissez Fond musical sur Marche, un écran s’afche pour vous permettre de dénir le fond musical.
Pour utiliser cette fonction, de la musique et des photos doivent être stockées sur l’unité USB.
Paramètres de musique de fond
Vous pouvez sélectionner la musique de fond d’un diaporama.
Si vous désactivez la fonction Fond musical, aucune musique ne sera diffusée, même si les réglages Paramètres de musique de fond ont été effectués.
Le changement du Mode mus. de fond exige le chargement de chiers musicaux. Lisez des chiers musicaux dans la
catégorie voulue.
Mode musicale → Humeur/Fichier sélectionné/Aléatoire
Fond musical → Energique/Rhytmique/Triste/Enivrante/Calme
Si vous dénissez Fond musical sur Humeur, vous pouvez sélectionner une ambiance.
Vous ne pouvez pas sélectionner une ambiance qui ne fait pas partie des chiers musicaux stockés sur l’unité USB.
Sél. ch. music.
Si vous dénissez Fond musical sur Fichier sélectionné, vous pouvez choisir un chier musical.
Réglage de l’image/Text du son
Reportez-vous à la page 43.
Information
Les informations relatives au chier photo sont afchées.
Retrait sécurisé
Vous pouvez retirer le périphérique du téléviseur en toute sécurité.
N
N
N
N
N
N
N
N
N
•
•
N
N
•
N
Outils
Arrêter le diaporama
Rotat.
Zoom
Vit. diaporama : Normal
Fond musicall : Arrêt
Paramètres de musique de fond
Réglage de l’image
Text du son
Information
U
Déplacer E Entrer e Quitter
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.