Page 1
¦¦ Connecting¦a¦AV¦device
W
R
HD¦connection
Using an HDMI Cable
HDMI OUT
HD¦connection
DVD / Blu-ray player
/ HD Cable Box / HD
STB (Set-Top-Box)
satellite receiver
Using an HDMI to DVI Cable
DVI OUT
DVD /
R
W
AUDIO OUT
Blu-ray player
EXT
VCR / DVD
Using a Scart Cable
Y
W
R
Y
W
R
Component connection
Using a Component Cable
AUDIO OUTVIDEO OUT
VCR
Using an Audio/Video Cable
W
B
AUDIO OUTCOMPONENT OUT
RRG
RGB
W
R
DVD, Blu-ray
player, cable
box, STB satellite
receiver, VCR
English -4
Page 2
Plasma TV
QUICK SETUP GUIDE
¦¦ The¦Supplied¦Accessories
yRemote Control & Batteries (AAA x 2)
y Owner’s Instructions
y Warranty Card / Safety Guide (Not available in some locations)
yBlanking Bracket yFerrite Core (3EA)
See separate guide for installing the stand.
yStand (1EA) yGuide Stand (1EA) yScrews (10EA)
Ferrite Core: The ferrite cores are used to shield the cables from interference. When connecting a cable, open the ferrite core
✎
and clip it around the cable near the plug as shown in the figure.
yDistance between the ferrite core and one end of the cord put into the TV set
yA : below 50 mm
yB : below 20 mm
A
B
C
yCleaning Cloth
y Power Cord
(depending on the country)
(M4 X L16)
yC : 100 ~ 150 mm
yD : below 15 mm
D
(Switzerland only)
English - 1
BN68-02789A-01
Page 3
¦¦ Installing¦the¦Stand
INFO
S
OURC
E
C
H LI
ST
TTX/MIX
Preset Step¦1 Step¦2
Front
s
s
s
s
Front
s
s
s
s
Back
✎
Preset: Place the Guide Stand and Cover Neck onto the stand and fasten it using the screws. Applicable to models
Back
(Depending on the model)
Step¦1.¦ Attach your PDP TV to the stand.
✎
Two or more people should carry the TV.
✎
Make sure to distinguish between the front and back of the stand when assembling them.
✎
To make sure the TV is installed on the stand at a proper level, do not apply excess downward pressure to the upper
left of right sides of the TV.
Step¦2.¦ Fasten two screws at position 1 and then fasten two screw at position 2.
✎
Stand the product up and fasten the screws. If you fasten the screws with the PDP TV placed down, it may lean to
one side.
¦¦ Using¦the¦remote¦control¦buttons
ENTER
E
/ DIRECTION Buttons
Move the cursor and select an
item. Select the currently selected
item. Confirm the setting.
RETURN Button
Return to the previous menu.
.
RETURN
ΕΧΙΤ
MENU Button
Display the main on-screen menu.
EXIT
Exit the on-screen menu.
¦¦ Installing¦Batteries¦in¦the¦Remote¦Control
English - 2
Page 4
¦¦ Plug¦&¦Play
Plug & Play
Plug & Play
Plug & Play
Plug & Play
Plug & Play
Plug & Play
Plug & Play
Plug & Play
How to get the best perfotmance from your new HDTV
1/2
Step 1. Connect the HD Box to the using HDMI or Component
cables.
TV rear view ►
HDMI Cable
HDMI Cable
When the TV is initially powered on, basic settings proceed automatically and subsequently.
If you want to reset this feature, press the MENU button to display menu.
You can set the Plug & Play by selecting ‘Setup → Plug & Play’.
VHF/UHF Antenna
or
Power Input
On the screen, you can set as follows.
✎
The each step may vary depending on the Antenna source.
Step 1
Step¦2 Step¦3
Cable
ANT OUT
Select the OSD Language.
Menu Language : : English
Nederlands
English
Eesti
U
▲
▼
Move E Enter
Step¦4 Step¦5 Step¦6
Antenna Source : Air ►
Channel Source : Digital & Analogue
Serch
Previous Skip U Move E Enter
Step¦7 Step¦8
Select the usage mode.
Store Demo
Previous U Move E Enter
Auto Store in progress.
Channels : 7
Digital
Analogue 0
TV:2 Radio:0 Data/Other: 0
Stop
Enjoy your TV.
Home Use
2
Select Country.
Country :
▲
Turkey
United Kingdom
Estonia
▼
U
Move E Enter
Set the Clock Mode.
15%
E
Enter
Clock Mode : Manual ►
Auto
Manual
U
Move E Enter
OK
Previous Skip ► Next
English - 3
Loading...