Samsung PS50A556S2F User Manual [bg]
Contact SAMSUNG WORLD-WIDE
If you have any questions or comments relating to Samsung products, please contact the SAMSUNG
customer care centre.
Country
AUSTRIA 0800-SAMSUNG(726-7864) www.samsung.com/at
BELGIUM 0032 (0)2 201 24 18 www.samsung.com/be
CZECH REPUBLIC
DENMARK 70 70 19 70 www.samsung.com/dk
EIRE 0818 717 100 www.samsung.com/ie
ESTONIA 800-7267 www.samsung.ee
FINLAND 030-6227 515 www.samsung.com/fi
FRANCE
GERMANY 01805 - SAMSUNG(726-7864 € 0,14/Min) www.samsung.com
HUNGARY 06-80-SAMSUNG(726-7864) www.samsung.com
ITALIA 800-SAMSUNG(726-7864) www.samsung.com
KAZAKHSTAN 8-10-800-500-55-500 www.samsung.kz
KYRGYZSTAN 00-800-500-55-500 LATVIA 800-7267 www.samsung.com/lv
LITHUANIA 8-800-77777 www.samsung.lt
LUXEMBURG 0035 (0)2 261 03 710 www.samsung.com/be
NETHERLANDS 0900-SAMSUNG (726-7864 € 0,10/Min) www.samsung.com/nl
NORWAY 815-56 480 www.samsung.com/no
POLAND
PORTUGAL 80820-SAMSUNG(726-7864) www.samsung.com/pt
RUSSIA 8-800-555-55-55 www.samsung.com
SLOVAKIA 0800-SAMSUNG(726-7864) www.samsung.com/sk
SPAIN 902 10 11 30 www.samsung.com
SWEDEN 0771-400 200 www.samsung.com/se
SWITZERLAND 0800-SAMSUNG(726-7864) www.samsung.com/ch
TURKEY 444 77 11 www.samsung.com
TADJIKISTAN 8-10-800-500-55-500 U.K 0845 SAMSUNG (7267864) www.samsung.com
UKRAINE 8-800-502-0000 www.samsung.com
UZBEKISTAN 8-10-800-500-55-500 www.samsung.uz
Customer Care Centre
844 000 844 www.samsung.com/cz
Distributor pro Českou republiku:
Samsung Zrt., česka organizační složka Vyskočilova 4, 14000 Praha 4
"3260 SAMSUNG (€ 0,15/Min)
08 25 08 65 65 (€ 0,15/Min)"
"0 801 801 881
022-607-93-33"
Web Site
www.samsung.com
www.samsung.com/pl
Plasma TV
user manual
imagine the possibilities
Thank you for purchasing this Samsung product.
To receive more complete service, please
register your product at
www.samsung.com/global/register
Model Serial No.
BN68-01427B-00
User Instructions
Screen Image retention
Do not display a still image (such as on a video game or when hooking up a PC to this PDP) on the
plasma monitor panel for more than 2 hours as it can cause screen image retention. This image
retention is also known as “screen burn”. To avoid such image retention, reduce the degree of
brightness and contrast of the screen when displaying a still image.
Height
The PDP can normally operate only under 2000m in height. It might abnormally function at a place
over 2000m in height so do not install and operate there.
Heat on the top of the PDP TV
The top side of the product may be hot after long period of use as heat dissipates from the panel
through the vent hole in the upper part of the product. This is normal and does not indicate any defect
or operation failure of the product. However, children should be prevented from touching the upper
part of the product.
The product is making a ‘cracking’ noise.
A ‘cracking’ noise may occur when the product contracts or expands due to a change of surrounding
environment such as temperature or humidity. This is normal and not a defect of the unit.
Cell Defects
The PDP uses a panel consisting of 1,230,000(SD-level) to 3,150,000(HD-level) pixels which require
sophisticated technology to produce. However, there may be few bright or dark pixels on the screen.
These pixels will have no impact on the performance of the product.
Avoid operating the TV at temperatures below 5°C(41°F)
A still image displayed too long may cause permanent damage to the PDP Panel.
Afterimage on the Screen.
Displaying still images from Video games and PC for longer than a certain period of time may
produce partial afterimages. To prevent this effect, reduce the ‘brightness’ and ‘contrast’ when
displaying still images.
Warranty
- Warranty does not cover any damage caused by image retention.
- Burn-in is not covered by the warranty.
Installation
Be sure to contact an authorized service centre, when installing your set in a location with heavy
dust, high or low temperatures, high humidity, chemical substance and where it operates continually
such as the airport, the train station etc. Failure to do so may cause a serious damage to your set.
Watching the PDP TV in 4:3 format for a long period of time may leave traces
of borders displayed on the left, right and centre of the screen caused by the
difference of light emission on the screen. Playing a DVD or a game console
may cause similar effect to the screen. Damages caused by the above effect are
not covered by the Warranty.
Any functions related to Digital TV (DVB) will only work in countries or areas where DVB-T (MPEG2)
digital terrestrial signals are broadcasted. Please confirm with your local dealer if you can receive
DVB-T signals. Although this TV set follows the DVB-T specification, maintaining compatibility with
the future coming DVB-T digital terrestrial broadcasts is not guaranteed. Several functions may not be
available in some countries.
Contact SAMSUNG WORLDWIDE
If you have any questions or comments relating to Samsung products, please contact the SAMSUNG
customer care centre. (See back cover for more informations.)
© 2008 Samsung Electronics Co., Ltd. All rights reserved.
English - 2
Contents
English
General Information
User Instructions ............................................. 2
Checking Parts ................................................ 4
Using the Stand-Base ..................................... 4
Control Panel .................................................5
Connection Panel ............................................ 6
Viewing the Remote Control ...........................8
Operation
Switching Your Television On and Off .............9
Viewing the Menus .......................................... 9
Plug & Play Feature ...................................... 10
Using the TOOLS Button ..............................12
Viewing External Signal Sources .................. 12
Editing Device Names ................................... 13
Channel Control
Storing Channels Automatically .................... 13
Storing Channels Manually ........................... 14
Adding / Locking Channels ...........................15
Sorting the Stored Channels ......................... 16
Assigning Names to Channels ...................... 16
Fine Tuning Channel Reception ....................17
LNA (Low Noise Amplier) ............................ 17
Picture Control
Changing the Picture Standard ..................... 18
Customizing the Picture Settings .................. 18
Conguring Detailed Settings on the Picture
Picture Options ............................................. 20
Resetting the Picture Settings to the Factory
Defaults ......................................................... 22
.... 19
Sound Control
Sound Features ............................................ 23
Selecting the Sound Mode
(depending on the model) ............................. 24
Connecting Headphones (Sold separately) ..24
PC Display
Setting up Your PC Software
(Based on Windows XP) ............................... 28
Input Mode (PC) ............................................ 29
Setting the PC ............................................... 30
Using the DTV Feature
Previewing the DTV Menu System ...............31
Displaying Programme Information ............... 32
Operating the DTV Menu .............................. 33
WISELINK
Using the WISELINK Function ...................... 43
Using the WISELINK Menu ........................... 44
Using the PHOTO (JPEG) List ...................... 45
Using the MP3 List ........................................ 48
Using the Setup Menu .................................. 49
About Anynet
What is Anynet+? .......................................... 51
Connecting Anynet+ Devices ........................ 51
Setting Up Anynet
Scanning and Switching between
Anynet+ Devices ........................................... 52
Recording ...................................................... 53
Listening through a Receiver ........................54
Check Points before Requesting Service ..... 54
+
+ ....................................... 52
Appendix
Teletext Feature (depending on the model) .. 55
Wall Mount Kit Specications (VESA) ........... 57
Wall- mount adjustment (Sold separately) .... 58
How to assemble the Stand-Base
(depending on the model) ............................. 59
Troubleshooting ............................................60
Specications ................................................ 61
Function Description
Time Features ............................................... 25
Language / Light Effect / Melody /
Entertainment / Energy Saving / PIP ............26
Symbols
Press
English - 3
Important
Note
Checking Parts
Owner’s Instructions Remote Control/
Cover-Bottom / Screws (2ea)
(Refer to page 59)
Antenna Cable Component Cables Audio Cables PC Cable
Scart Cable PC Audio Cable HDMI Cable HDMI/DVI Cable
Ferrite Core (Power Cord, S-Video, Component)
The ferrite cores are used to shield the cables from
interference.
When connecting a cable, open the ferrite core and clip it
around the cable near the plug.
AAA Batteries
Ferrite Core for
Power Cord
Power Cord Cloth-Clean Warranty Card/
Ferrite Core for
S-Video
Sold Separately
Ferrite Core for
Component
Registration Card/
Safety Guide Manual
Using the Stand-Base
Two or more people should carry
the PDP. Never lay the PDP on the
floor because of possible damage
to the screen. Always keep the
PDP upright.
The PDP can rotate 20 degrees in
right and left directions.
-20° ~ 20°
English - 4
Control Panel
Front Panel
The product colour and shape may vary depending on the model.
1
SOURCE
Toggles between all the available input sources
(TV, Ext.1, Ext.2, AV, S-Video, Component, PC,
HDMI1, HDMI2, HDMI3, DTV).
In the on-screen menu, use this button as
you would use the ENTER button on the
remote control.
2
MENU
Press to see an on-screen menu of your TV’s
features.
3
– +
Press to increase or decrease the volume. In
the on-screen menu, use the – + buttons
as you would use the ◄ and ► buttons on the
remote control.
4
Press to change channels.
In the on-screen menu, use the
buttons as you would use the ▲ and ▼ buttons
on the remote control.
5
Power Indicator
Blinks and turns off when the power is on and
lights up in stand-by mode.
6
POWER
Press to turn the TV on and off.
7
Remote Control Sensor
Aim the remote control towards this spot on the
TV.
8
Speakers
English - 5
Connection Panel
Rear Panel
1
9
or
Cable Television
Network
or
432 6 85
The product colour and shape may vary depending on the model.
Whenever you connect an audio or video system to your set, ensure that all elements are
switched off.
When connecting an external device, match the colour of the connection terminal to the cable.
1
POWER IN
Connect the supplied power cord.
2
COMPONENT IN
Audio (AUDIO L/R) and video (Y/P
for Component.
3
PC IN(PC) / (AUDIO)
Connect to the video and audio output jack on
your PC.
4
EXT 1, EXT 2
Inputs or outputs for external devices, such as
VCR, DVD, video game device or video disc
players.
Input/Output Specification
Connector
EXT 1
EXT 2
Input Output
Video Audio(L/R) RGB
B/PR) inputs
Video + Audio(L/R)
Only TV or DTV
output is available.
Output you can
choose.
5
DIGITAL AUDIO OUT (OPTICAL)
Connect to a Digital Audio Component.
6
Connecting external Audio Devices
Connect RCA audio signals from the TV to an
external source, such as Audio equipment.
7
SERVICE
− Connector for service.
− Connect the serial jack between the
electro-motion wall mount bracket and your
TV when you want to adjust the TV viewing
angle using your remote control.
7
English - 6
Continued...
8
HDMI IN 1,2
− No additional Audio connection is needed
for an HDMI to HDMI connection.
- When using an HDMI/DVI cable connection,
you must use the HDMI IN 2 jack.
What is HDMI?
- “High Definition Multimedia interface”
allows the ansmission of high definition
digital video data and multiple channels
of digital audio.
- The HDMI/DVI terminal supports DVI
connection to an extended device with
the appropriate cable (not supplied).
The difference between HDMI and DVI
is that the HDMI device is smaller in
size, has the HDCP (High Bandwidth
Digital Copy Protection) coding feature
installed, and supports multi - channel
digital audio.
Side Panel
2
4
DVI IN (HDMI 2) AUDIO R/L
DVI audio outputs for external devices.
9
ANT IN
75Ω Coaxial connector for Aerial/Cable
Network.
Supported modes for HDMI/DVI and Component
HDMI/DVI 50Hz X X X O O O O
HDMI/DVI 60Hz X O X X O O O
Component O O O O O O O
3
or
480i 480p 576i 576p 720p 1080i
1
1080p
The product colour and shape may vary depending on the model.
1
COMMON INTERFACE Slot
Insert CI (Common Interface) card into the slot.
(refer to page 42)
−
When ‘CI Card’ isn’t inserted in some
channels, “Scramble Signal” is displayed on
the screen.
− Th e pa i r ing infor m a t ion conta i n i ng a
telephone number, CI CARD ID, Host ID,
and other information will be displayed in
about 2~3 minutes. If an error message
is displayed, please contact your service
provider.
− When the channel information configuration
has fi n i s hed, th e mes s a g e “Upda t i n g
Completed” is displayed, indicating that the
channel list is now updated.
Insert the CI-Card in the direction marked
on it.
English - 7
2
HDMI IN 3
Connect to the HDMI jack of a device with
HDMI output.
3
WISELINK
Connect a USB mass storage device to view
photo files (JPEG) and play audio files (MP3).
4
S-VIDEO or VIDEO / AUDIO L/R
Video (S-Video or Video) and audio inputs
for external devices, such as a camcorder or
VCR.
5
Headphones jack
You can connect a set of headphones if you
wish to watch a television programme without
disturbing the other people in the room.
Prolonged use of headphones at a high
volume may damage your hearing.
5
Viewing the Remote Control
The performance of the remote control may be affected by bright light.
1
POWER button
(turns the TV on and off)
2
Selects the TV and DTV
mode directly
3
Number buttons for direct
channel access
4
One/Two-digit channel
selection
5
Temporary sound switch-off
6
Volume increase
Volume decrease
7
Electronic Program Guide
(EPG) display
8
Use to quickly select
frequently used functions.
9
Control the cursor in the
menu
0
Use to see information on
the current broadcast
#
Press to select the optional
display and sound modes for
sports, cinema and games.
$
VCR/DVD Function (Rewind,
Stop, Play/Pause, Fast/
Forward)
%
Available source selection
^
Previous channel
&
Next channel
Previous channel
*
Displays the main on-screen
menu
(
This function enables you to
view and play photo (JPEG)
and audio files (MP3) from
an external device. (See
page 45 (JPEG), 48 (MP3))
)
Returns to the previous
menu
a
Exit the on-screen menu
b
Picture size selection
c Use this when connecting
a SAMSUNG DMA (Digital
Media Adapter) device
through an HDMI interface
and switching to DMA mode.
(The DMA button is optional.)
For more information on the
operating procedures, refer
to the user manual of the
DMA. This button is available
when “Anynet+(HDMI-CEC)"
is “On” (see page 52)
d
Digital subtitle display
e
Channel control button
(Refer to page 15)
Teletext Functions
(Refer to page 55)
2
Exit from the teletext display
(depending on the model)
7
Teletext store
8
Teletext size
0
Teletext reveal
!
Fastext topic selection
@
Teletext display/mix both
teletext information and the
normal broadcast
%
Teletext mode selection
(LIST/FLOF)
^
Teletext sub page
&
P :Teletext next page
P :Teletext previous page
*
Teletext index
)
Teletext hold
a
Teletext cancel
English - 8
Continued...
Installing Batteries in the Remote Control
1 Lift the cover at the back of the remote control upward as
shown in the figure.
2 Install two AAA size batteries.
Make sure to match the “+” and “–” ends of the
batteries with the diagram inside the compartment.
Do not mix battery types, i.e. alkaline and manganese.
3 Close the cover as shown in the figure.
Remove the batteries and store them in a cool and dry
place if you won’t be using the remote control for a long
time. The remote control can be used up to about 23 feet
from the TV. (Assuming typical TV usage, the batteries last
for about one year.)
If the remote control doesn’t work! Check the following:
1. Is the TV power on?
2. Are the plus and minus ends of the batteries reversed?
3. Are the batteries drained?
4. Is there a power cut, or is the power cord unplugged?
5. Is there a special fluorescent light or a neon sign nearby?
Switching Your Television On and Off
The mains lead is attached to the rear of the television.
1 Plug the mains lead into an appropriate socket.
The main voltage is indicated on the rear of the television and the frequency is 50 or 60Hz.
2 Press the (Power) button (On/Off) on the front of the television or press the POWER button on
the remote control to switch the television on. The channel that you were watching last is re-selected
automatically. If you have not yet stored any channels, no clear picture appears. Refer to “Storing
Channels Automatically” on page 13 or “Storing Channels Manually” on page 14.
If the television is initially powered on, several basic customer settings proceed automatically.
Refer to “Plug & Play Feature” on page 10.
3 To switch the television off, press the (Power) button (On/Off) on the front of the television or press
the POWER button on the remote control.
4 To switch the TV on, press the (Power) button (On/Off) on the front of the TV or press the POWER
button or number buttons on the remote control.
Viewing the Menus
1 Press the MENU button.
The main menu is displayed on the screen.
Its left side has six icons: Picture, Sound, Channel, Setup,
Input, and Digital Menu.
2 Press the ▲ or ▼ button to select one of the icons.
Press the ENTER button to access the icon’s sub-menu.
3 Press the ▲ or ▼ button to move to items in the menu.
Press the ENTER button to enter items in the menu.
4 Press the ▲/▼/◄/► button to change the selected items.
Press the RETURN button to return to the previous menu.
5 Press the EXIT button to exit from the menu.
English - 9
T V
Mode : Standard
Cell Light 7
Contrast 80
Brightness 45
Sharpness 50
Colour 50
Tint G50 R50
Detailed Settings
More
Move
Picture
Enter
Exit
Plug & Play Feature
When the television is initially powered on, several basic
customer settings proceed automatically and subsequently.
The following settings are available.
If you accidentally select the wrong country for your TV, the
characters on the screen may be wrongly displayed.
Any functions related to Digital TV (DVB) will only work in
countries or areas where DVB-T (MPEG2) digital terrestrial
signals are broadcasted. Please confirm with your local
dealer if you can receive DVB-T signals. Although this TV set
follows the DVB-T specification, maintaining compatibility with
the future coming DVB-T digital terrestrial broadcasts is not
guaranteed. Several functions may not be available in some
countries.
1 If the television is in standby mode, press the POWER button
on the remote control. The message Start Plug & Play is
displayed. Press the ENTER button.
2 The Language menu will automatically appear after several
seconds.
3 Select the appropriate language by pressing the ▲ or ▼
button.
Press the ENTER button. The message Select ‘Home Use’
when installing this TV in your home. is displayed.
4 Press the ◄ or ► button to select Store Demo or Home Use,
then press the ENTER button. The message to check the
connected status of the antenna is displayed.
The default selection is Home Use.
We recommend setting the TV to Home Use mode for the
best picture in your home environment.
Store Demo mode is only intended for use in retail
environments.
If the unit is accidentally set to Store Demo mode and you
want to return to Home Use (Standard): Press the Volume
button. When the volume OSD is displayed, press and
hold the MENU button for 5 seconds.
5 Make sure that the antenna is connected to the TV.
Press the ENTER button. The Country menu is displayed.
6 Select your country or area by pressing the ▲ or ▼ button.
Press the ENTER button.
The message Some DTV functions may not be available.
Digital Scan? is displayed.
This function is supported for all countries except for the
following countries: France, Germany, Italy, Netherlands,
Spain, Switzerland, United Kingdom, Austria.
If your country supports the DTV functions, the message is
not displayed. Then you can follow the instructions from step
12
. When the local service provider does not support DTV
broadcasting but you choose a DTV supporting country, it
enters the DTV Plug & Play but DTV functions may not work
properly.When No is selected, follow the instructions from step
7 to 10. When Yes is selected, follow the instructions from
step 11.
Plug & Play
Start Plug & Play.
OK
Enter
Plug & Play
Language
Move
when installing this TV in your home.
Move
Enter
Country
Move
Some DTV functions may not be available.
Digital Scan?
Move
P 1 C -- 40 MHz
0 %
Enter
English
Deutsch
Français
Italiano
▼
Enter
Plug & Play
Select ‘Home Use’
Store Demo Home Use
Enter
Plug & Play
Check antenna input.
OK
Plug & Play
▲
United Kingdom
Austria
Eastern Europe
Others
Enter
Plug & Play
Yes No
Enter
Plug & Play
Start
Skip
Skip
English - 10
Continued...
7 Select No pressing the ◄ or ► button, then press the ENTER
button. Auto Store menu is displayed.
8 Press the ENTER button to start search the channels. The
channel search will start and end automatically. After all the
available channels are stored, Clock Set menu is automatically
displayed. Press the ENTER button.
To stop the search before it has finished, press the
ENTER button with Stop selected.
9 Press the ◄ or ► button to select Month, Day, Year, Hour, or
Minute. Set these by pressing the ▲ or ▼ button.
You can set the Month, Day, Year, Hour, or Minute
directly by pressing the numeric buttons on the remote
control.
10 Press the ENTER button to confirm your setting. The message
Enjoy your viewing is displayed. When you have finished,
press the ENTER button.
Even if the ENTER button is not pressed, the message will
automatically disappear after several seconds.
11 Select Yes pressing the ◄ or ► button, then press the
ENTER button. Auto Store menu is displayed.
12 Press the
ENTER button to start search the analog channels.
The analog channel search will start and end automatically.
After all the available analog channels are stored, the screen
for searching digital channels is automatically displayed.
To stop the search before it has finished, press the
ENTER button with Stop selected.
13 Press the
ENTER button to start search the digital channels.
The digital channel search will start and end automatically.
After all the available digital channels are stored, the screen to
select a time zone is displayed depending on the country.
To stop the search before it has finished, press the
ENTER button with Stop selected.
If the DTV channel is updated, the Source in the source
list of the Input menu is automatically changed to DTV.
For detailed descriptions about DTV channel update, refer
to page 33 of this manual.
14 Press the ▲ or ▼ button to select required time zone, then
press the ENTER button. The screen for setting the time is
displayed. Press the ENTER button.
15 Press the ◄ or ► button to select Month, Day, Year, Hour, or
Min. Set these by pressing the ▲ or ▼ button.
You can set the Month, Day, Year, Hour, or Min directly
by pressing the numeric buttons on the remote control.
16 Press the
ENTER button to confirm your setting. The message
Enjoy your viewing is displayed. When you have finished,
press the ENTER button.
Even if the ENTER button is not pressed, the message will
automatically disappear after several seconds.
If you want to reset this feature …
Press the MENU button to display the menu.
1
2 Press the ▲ or ▼ button to select Setup, then press the
ENTER button.
3 Press the ENTER button again to select Plug & Play.
The message Start Plug & Play is displayed.
Month Day Year
01
Hour Min
12 00
Move
Enter
Enter
Plug & Play
15
Adjust
Plug & Play
Start
Skip
Plug & Play
Stop
Skip
Plug & Play
2008
-
Enter
Skip
Clock Set
0%
Services found: 0 Channel:
Scanning for digital services...
29%
Services found: 6 Channel: 35
The Iberian Peninsula and Balears Islands
Canarian Islands
Move Select
<Spain only>
Set the current time.
Adjust Move
T V
Plug & Play
Month Day Year
15
OK
Setup
:
: Off
2008
Enter
In Watching TV
Off
01
Hour Min
12 00
Enjoy your viewing
Plug & Play
Language : English
Time
Light Effect
Auto Wall-Mount
Melody : Off
Entertainment
Energy Saving :
PIP
Skip
English - 11
Move
Enter
Return
Using the TOOLS Button
You can use the TOOLS button to select your frequently used functions quickly and easily. The
“Tools” menu changes depending on which external input mode you are viewing.
1 Press the TOOLS button.
The Tools menu will appear.
2 Press the ▲ or ▼ button to select a menu, then press the
ENTER button.
3 Press the ▲/▼/◄/►/ENTER buttons to display, change, or
use the selected items.
For a more detailed description of each function, refer to the
Anynet+ (HDMI-CEC)
Picture Mode : Standard
Sound Mode : Custom
Sleep Timer : Off
SRS TS XT : Off
Energy Saving : Off
Dual I-II : Mono
Move
Tools
Enter
Exit
corresponding page.
• Anynet+(HDMI-CEC), see page 52
• Picture Mode, see page 18
• Sound Mode, see page 23
• Sleep Timer, see page 25
• SRS TS XT, see page 23
• Energy Saving, see page 27
• Dual I-II, see page 24
Viewing External Signal Sources
You can switch between viewing signals from connected
equipment, such as a VCR, DVD, Set-Top Box, and the TV
T V
source (broadcast or cable).
1 Press the MENU button to display the menu.
2 Press the ▲ or ▼ button to select Input, then press the ENTER
button.
3 Press the ENTER button again to select Source List.
4 Press the ▲ or ▼ button to select the signal source, then press
the ENTER button.
Available signal sources:
Component, PC, HDMI1, HDMI2, HDMI3, DTV
You can choose only those external devices that are connected
to the TV.
You can select these options simply by pressing the SOURCE
button on the remote control.
To watch television programme again, press the TV/DTV button
and select the channel number required.
TV, Ext.1, Ext.2, AV, S-Video,
English - 12
T V
Input
Source List
TV
Enter
Enter
Return
Return
Source List :
Edit Name
Anynet + (HDMI-CEC)
WISELINK
Move
TV
Ext.1 :−−−−
Ext.2 :−−−−
AV :−−−−
S-Video :−−−−
Component :−−−−
PC :−−−−
More
Move
Editing Device Names
You can give a name to the external source.
T V
1 Press the MENU button to display the menu.
2 Press the ▲ or ▼ button to select Input, then press the
ENTER button.
3 Press the ▲ or ▼ button to select Edit Name, then press the
ENTER button.
4 Press the ▲ or ▼ button to select the external source to be
edited, then press the ENTER button.
5 Select the required device by pressing ▲ or ▼, then press the
ENTER button.
Available device names:
VCR, DVD, Cable STB, Satellite
T V
STB, PVR STB, AV Receiver, Game, Camcorder, PC, TV,
IPTV, Blu-Ray, HD DVD, DMA.
6 Press the EXIT button to exit.
Storing Channels Automatically
Not available in DTV or external input mode.
You can scan for the frequency ranges available to you
(availability depends on your country).
Automatically allocated programme numbers may not
correspond to actual or desired programme numbers.
However you can sort numbers manually and clear any
channels you do not wish to watch.
1 Press the MENU button to display the menu.
2 Press the ▲ or ▼ button to select Channel, then press the
ENTER button.
3 Press the ENTER button again. The available countries are
listed.
4 Select your country by pressing the ▲ or ▼ button, then press
the ENTER button.
Even though you have changed the country setting in this
menu, the country setting for DTV is not changed. Use the
Plug & Play function to change the country setting for DTV.
(Refer to pages 10 to 11)
5 Press the ▲ or ▼ button to select Auto Store, then press the
ENTER button.
6 Press the ENTER button again to start the search.
The search will end automatically.
To stop the search before it has finished, press the MENU
or the ENTER button.
T V
T V
Input
Edit Name
Channel
Channel
Auto Store
Start
Return
TV
Enter
−−−−
VCR
DVD
Cable STB
Satellite STB
PVR STB
AV Receiver
−−−−
Enter
▲
United Kingdom
Switzerland
United Kingdom
Austria
Eastern Europe
Others
Off
Enter
United Kingdom
Off
Enter
Return
Return
Return
Return
Source List :
Edit Name
Anynet + (HDMI-CEC)
WISELINK
Move
Ext.1 :−−−−
Ext.2 : −−−−
AV :
S-Video :
Component : −−−−
PC : −−−−
HDMI1 :
HDMI2 : −−−−
HDMI3 :
Move
Country :
Auto Store
Manual Store
Channel Manager
Sort
Name
Fine Tune
LNA :
Move
Country :
Auto Store
Manual Store
Channel Manager
Sort
Name
Fine Tune
LNA :
Move
P 1 C -- 40 MHz
0 %
Enter
English - 13
Storing Channels Manually
Not available in DTV or external input mode.
You can store television channels, including those received via
cable networks.
When storing channels manually, you can choose:
Whether or not to store each of the channels found.
The programme number of each stored channel which you wish
to identify.
T V
Country :
Auto Store
Manual Store
Channel Manager
Sort
Name
Fine Tune
LNA :
Channel
1 Press the MENU button to display the menu.
2 Press the ▲ or ▼ button to select Channel, then press the
ENTER button.
3 Press the ▲ or ▼ button to select Manual Store, then press
T V
the ENTER button.
4 Select the required option by pressing the ▲ or ▼ button, then
press the ENTER button.
5 When you are satisfied with your setting, press the ENTER
Move
Programme :
Colour System : Auto
Sound System : BG
Channel : C
Search : 175 MHz
Store : ?
Enter
Manual Store
P 1
button.
6 Press the EXIT button to exit.
Move
Programme (Programme number to be assigned to a channel)
Enter
− Press the ▲ or ▼ button until you find the correct number.
You can also select the channel number directly by pressing the numeric buttons (0~9).
Colour System: Auto/PAL/SECAM/NTSC4.43
− Press the ▲ or ▼ button to select the required colour standard.
Sound System: BG/DK/I/L
− Press the ▲ or ▼ button to select the required sound standard.
Channel (When you know the number of the channel to be stored)
− Press the ▲ or ▼ button to select
C (Air channel) or S (Cable channel).
− Press the ► button, then press the ▲ or ▼ button to select the required number.
You can also select the channel number directly by pressing the numeric buttons (0~9).
If there is abnormal sound or no sound, re-select the sound standard required.
Search (When you do not know the channel numbers)
− Press the ▲ or ▼ button to start the search.
− The tuner scans the frequency range until the first channel or the channel that you selected is
received on the screen.
Store (When you store the channel and associated programme number)
− Set to
OK by pressing the ENTER button.
Channel mode
P (Programme mode): When completing tuning, the broadcasting stations in your area have
been assigned to position numbers from P00 to P99. You can select a channel by entering the
position number in this mode.
C (Air channel mode): You can select a channel by entering the assigned number to each air
broadcasting station in this mode.
S (Cable channel mode): You can select a channel by entering the assigned number for each
cable channel in this mode.
United Kingdom
Off
Return
Return
English - 14
Adding / Locking Channels
Not available in DTV or external input mode.
Using the Channel Manager, you can conveniently lock or add
T V
channels.
1 Press the MENU button to display the menu.
2 Press the ▲ or ▼ button to select Channel, then press the
ENTER button.
3 Press the ▲ or ▼ button to select Channel Manager, then
press the ENTER button.
Adding channels
Using the Channel List, you can add channels.
T V
4 Select Channel List by pressing the ENTER button.
5 Move to the ( ) field by pressing the ▲/▼/◄/► buttons,
select a channel to be added, and press the ENTER button to
add the channel.
If you press the ENTER button again, the ( ) symbol next
to the channel disappears and the channel is not added.
Locking channels
This feature allows you to prevent unauthorized users, such as
children, from watching unsuitable programmes by muting out video
and audio.
6 Press the ▲ or ▼ button to select Child Lock, then press the ENTER
button.
7 Select On by pressing the ▲ or ▼ button, then press the ENTER
button.
8 Press the ▲ or ▼ button to select Channel List, then press the
ENTER button.
9 Move to the ( ) field by pressing the ▲/▼/◄/► buttons, select a
channel to be locked, and press the ENTER button.
If you press the ENTER button again, the ( ) symbol next to the
channel disappears and the channel lock is canceled.
A blue screen is displayed when Child Lock is activated.
10 Press the EXIT button to exit.
You can select these options simply by pressing the CH LIST
button on the remote control.
Channel
Country :
Auto Store
Manual Store
Channel Manager
Sort
Name
Fine Tune
LNA :
Move
Channel List
Child Lock : Off
Move
P 1 C 6
Prog.
0
1 C 6
2 C 5
3 C 8
4 C 11
5 C 22
6 C 26
7 C 36
8 C 52
9 C 24
Add Lock
Move Enter
Page Return
United Kingdom
Off
Enter
Channel Manager
Enter
Channel List
C 1
Return
Return
1 / 10
▲
▼
English - 15
Sorting the Stored Channels
Not available in DTV or external input mode.
This operation allows you to change the programme numbers
T V
of the stored channels.
This operation may be necessary after using the auto store.
1 Press the MENU button to display the menu.
2 Press the ▲ or ▼ button to select Channel, then press the
ENTER button.
3 Press the ▲ or ▼ button to select Sort, then press the
ENTER button.
4 Select the channel that you wish to move by pressing the
▲ or ▼ button, then press the ENTER button.
T V
5 Select the number of the programme to which the channel is to
be moved by pressing the ▲ or ▼ button.
Press the ENTER button. The channel is moved to its new
position and all other channels are shifted accordingly.
6 Repeat steps 4 to 5 until you have moved all the channels to
the required programme numbers.
7 Press the EXIT button to exit.
Assigning Names to Channels
Not available in DTV or external input mode.
Channel names will be assigned automatically when channel
information is broadcast. These names can be changed,
allowing you to assign new names.
1 Press the MENU button to display the menu.
2 Press the ▲ or ▼ button to select Channel, then press the
ENTER button.
3 Press the ▲ or ▼ button to select Name, then press the
ENTER button.
4 Press the ▲ or ▼ button to select the channel to be assigned
to a new name, then press the ENTER button.
5 Press the ▲ or ▼ button to select a letter, a number, or a
symbol (Results in this sequence: A~Z, 0~9, +, -, *, /, blank).
Move on to the previous or next letter by pressing the ◄ or ►
button, then press the ENTER button.
6 Repeat steps 4 to 5 for each channel to be assigned to a new
name.
7 Press the EXIT button to exit.
T V
T V
Channel
United Kingdom
Off
Enter
Sort
Enter
Channel
United Kingdom
Off
Enter
Name
Enter
Return
Return
Return
Return
Country :
Auto Store
Manual Store
Channel Manager
Sort
Name
Fine Tune
LNA :
Move
Prog. Ch. Name
0 C- -
1 C04
2 C05
3 C08
4 C09
Move
Country :
Auto Store
Manual Store
Channel Manager
Sort
Name
Fine Tune
LNA :
Move
Prog. Ch. Name
0 C-- −−−−−
1 C04 −−−−−
2 C05 −−−−−
3 C08 −−−−−
4 C09 −−−−−
Move
English - 16
Fine Tuning Channel Reception
Not available in DTV or external input mode.
If the reception is clear, you do not have to fine tune the
T V
channel, as this is done automatically during the search and
store operation.
If the signal is weak or distorted, you may have to fine tune the
channel manually.
1 Press the MENU button to display the menu.
2 Press the ▲ or ▼ button to select Channel, then press the
ENTER button.
3 Press the ▲ or ▼ button to select Fine Tune, then press the
ENTER button.
4 To obtain a sharp, and clear picture and good sound quality,
press the ◄ or ► button until you reach the optimal setting.
Press the ENTER button.
Fine Tune Store will change the colour of the Channel
OSD (On Screen Display) from White to Red and add the
“*” mark.
To reset the fine tuning to 0, select Reset by pressing the
▲ or ▼ button. Press the ENTER button.
5 Press the EXIT button to exit.
P 1 *
Mono
Picture : Dynamic
Sound : Custom
SRS TS XT : Off
−−
Move
Channel
Fine Tune
Reset
Save
Enter
Country :
Auto Store
Manual Store
Channel Manager
Sort
Name
Fine Tune
LNA :
P 1
Adjust
:
−−
United Kingdom
Off
Return
+ 3
Return
LNA (Low Noise Amplifier)
This function is very useful in the situation that the TV is used in weak signal.
LNA amplifies the TV signal in the weak signal area, a low-noise preamplifier boosts the incoming
signal.
1 Press the MENU button to display the menu.
2 Press the ▲ or ▼ button to select Channel, then press the
ENTER button.
3 Press the ▲ or ▼ button to select LNA, then press the ENTER
button.
4 Select Off or On by pressing the ▲ or ▼ button, then press
the ENTER button.
5 Press the EXIT button to exit.
Depending on areas, factory mode of LNA, will be set up as
On or Off.
English - 17
T V
Country :
Auto Store
Manual Store
Channel Manager
Sort
Name
Fine Tune
LNA :
Move
Channel
United Kingdom
Off
Enter
Return
Changing the Picture Standard
You can select the type of picture which best corresponds to
your viewing requirements.
1 Press the MENU button to display the menu.
2 Press the ENTER button to select Picture.
3 Press the ENTER button again to select Mode.
4 Select the required mode by pressing the ▲ or ▼ button, then
press the ENTER button.
Available modes:
The settings values may vary depending on the input
source.
5 Press the EXIT button to exit.
Choose Dynamic for viewing the TV during the day or
when there is bright light in the room.
Choose Standard for general TV watching mode.
Choose Movie when viewing the movie.
Dynamic, Standard, Movie
T V
Mode : Standard
Cell Light 7
Contrast 80
Brightness 45
Sharpness 50
Colour 50
Tint G50 R50
Detailed Settings
More
Move
T V
Mode : Standard
Cell Light 7
Contrast 80
Brightness 45
Sharpness 50
Colour 50
Tint G50 R50
Detailed Settings
More
Move
Picture
Enter
Picture
Enter
Dynamic
Standard
Movie
Return
Return
Easy Setting
1 Press the TOOLS button on the remote control.
2 Press the ▲ or ▼ button to select Picture Mode.
3 Press the ◄ or ► button to select the required option.
Anynet+ (HDMI-CEC)
PictureMode ◄ Standard ►
Sound Mode : Custom
Sleep Timer : Off
SRS TS XT : Off
Energy Saving : Off
Dual I-II : Mono
Move Adjust
Customizing the Picture Settings
Your television has several setting options that allow you to
control the picture quality.
1 Press the MENU button to display the menu.
2 Press the ENTER button to select Picture.
3 Press the ENTER button again to select Mode.
4 Select the required mode by pressing the ▲ or ▼ button, then
press the ENTER button.
Available modes:
Dynamic, Standard, Movie
5 Select the required option by pressing the ▲ or ▼ button, then
press the ENTER button.
6 When you are satisfied with your setting, press the ENTER button.
7 Press the EXIT button to exit.
Cell Light - Contrast – Brightness – Sharpness – Colour – Tint
In Analog TV, Ext., AV, S-Video modes of the PAL system, you cannot use the Tint Function.
In PC mode, you can only make changes to Cell Light, Contrast, and Brightness.
Press the ◄ or ► button until you reach the optimal setting.
T V
Mode : Standard
Cell Light 7
Contrast 80
Brightness 45
Sharpness 50
Colour 50
Tint G50 R50
Detailed Settings
More
Move
Tools
Picture
Enter
Exit
Return
English - 18
Configuring Detailed Settings on the Picture
You can set detailed picture settings.
1 Press the MENU button to display the menu.
2 Press the ENTER button to select Picture.
3 Press the ▲ or ▼ button to select Detailed Settings, then
press the ENTER button.
4 Select the required option by pressing the ▲ or ▼ button, then
press the ENTER button.
Available options:
Black Adjust, Dynamic Contrast,
Gamma, Colour Space, White Balance, Flesh Tone, Edge
Enhancement, xvYCC
5 When you are satisfied with your setting, press the ENTER
button.
6 Press the EXIT button to exit.
Detailed Settings is available in Standard or Movie mode.
In PC mode, you can only make changes to Dynamic
Contrast, Gamma and White Balance from among the
Detailed Settings items.
Black Adjust: Off/Low/Medium/High
You can directly select the black level on the screen to adjust the screen depth.
Dynamic Contrast: Off/Low/Medium/High
You can adjust the screen contrast so that the optimal contrast is provided.
Gamma: -3 ~ +3
You can adjust the middle brightness of pictures.
Press the ◄ or ► button until you reach the optimal setting.
Colour Space : Auto/Native/Custom
Colour space is a colour matrix composed of red, green and blue colours.
Select your favorite colour space to experience the most natural colour.
− Auto: Auto Colour Space automatically adjusts to the most natural colour tone based on program
sources.
− Native: Native Colour Space offers deep and rich colour tone.
− Custom: Adjusts the colour range to suit your preference. (see “Customizing the Colour Space”)
Customizing the Colour Space
Colour: Red/Green/Blue/Yellow/Cyan/Magenta
Adjusts the Colour range to suit your preference.
Colour is available when Colour Space is set to Custom.
Press the ▲ or ▼ button to select Red, Green, Blue, Yellow, Cyan or Magenta.
Press the ENTER button.
− Red/Green/Blue: In Colour, you can adjust the RGB values for the selected colour.
Press the ▲ or ▼ button to select Red, Green or Blue to change it. Press the ENTER button.
Press the ◄ or ► button to decrease or increase the value of a particular item.
Press the ENTER button.
− Reset: Resets the colour space to the default values.
White Balance: R-Offset/G-Offset/B-Offset/R-Gain/G-Gain/B-Gain/Reset
You can adjust the colour temperature for more natural picture colours.
R-Offset/G-Offset/B-Offset/R-Gain/G-Gain/B-Gain: Changing the adjustment value will refresh the
adjusted screen.
Select the required option by pressing the ▲ or ▼ button, then press the ENTER button.
Press the ◄ or ► button until you reach the optimal setting.
Reset: The previously adjusted white balance will be reset to the factory defaults.
T V
Mode : Standard
Cell Light 7
Contrast 80
Brightness 45
Sharpness 50
Colour 50
Tint G50 R50
Detailed Settings
More
Move
T V
Detailed Settings
Black Adjust :
Dynamic Contrast : Low
Gamma : 0
Colour Space : Native
White Balance
Flesh Tone : 0
Edge Enhancement
xvYCC : Off
Move
Picture
Enter
Off
: On
Enter
Return
Return
English - 19
Continued...
Flesh Tone:-15~+15
You can emphasize the pink tone in the picture.
Press the ◄ or ► button until you reach the optimal setting.
Changing the adjustment value will refresh the adjusted screen.
Edge Enhancement: Off/On
You can emphasize object boundaries.
xvYCC: Off/On
Setting the xvYCC mode to On increases detail and colour space when watching movies from an
external device (ie. DVD player) connected to the HDMI or Component IN jacks. You must set the
Picture Mode to Movie to enjoy this feature.
The xvYCC function works only in Component or HDMI(Y, Cb, Cr) mode.
Picture Options
You can set detailed picture settings.
1 Press the MENU button to display the menu.
2 Press the ENTER button to select Picture.
3 Press the ▲ or ▼ button to select Picture Options, then
press the ENTER button.
4 Select the required option by pressing the ▲ or ▼ button,
then press the ENTER button.
5 When you are satisfied with your setting, press the
ENTER button.
6 Press the EXIT button to exit.
In PC mode, you can only make changes to the Colour Tone,
Size and Screen Burn Protection from among the items in
Picture Options.
Colour Tone: Cool2/Cool1/Normal/Warm1/Warm2
When the picture mode is set to Dynamic or Standard,
Warm1 and Warm2 cannot be selected.
Size: Auto Wide/16:9/Wide Zoom/Zoom/4:3/Just Scan
You can select the picture size which best corresponds to your
viewing requirements.
−
Auto Wide: Expanding and pulling up the picture from 4:3 to
16:9 ratio.
− 16:9
: Sets the picture to 16:9 wide mode.
−
Wide Zoom: Magnify the size of the picture more than 4:3.
Move the screen up/down using the ▲ or ▼ button after
T V
Mode : Standard
Cell Light 7
Contrast 80
Brightness 45
Sharpness 50
Colour 50
Tint G50 R50
Detailed Settings
More
T V
Colour Tone : Normal
Size : Auto Wide
Screen Mode : 16:9
Digital NR : Auto
DNle : On
HDMI Black Level : Normal
Movie Plus : Low
Blue only mode : Off
Screen Burn Protection
T V
Auto Wide
16:9
Wide Zoom
Zoom
4:3
Just Scan
selecting the by pressing the ► or ENTER button.
−
Zoom: Magnify the size of the picture vertically on screen.
− 4:3
: Sets the picture to 4:3 normal mode.
−
Just Scan: Use this function to see the full image
without any cutoff when HDMI(720p/1080i/1080p),
Component(1080i/1080p) or DTV(1080i) signals are input.
After selecting Just Scan in HDMI (1080i/1080p) or
Component (1080i/1080p) mode: Press the ◄ or ► button
to select , then press the ENTER button. Press the ▲, ▼, ◄ or ► button to move the picture
up, down, left and right. Reset: Press the ◄ or ► button to select Reset, then press the ENTER
button. You can initialize the setting.
With the HDMI Just Scan picture size, depending on the AV devices, the screen may be cut off
or a specific colour appears on the screen.
For an HDMI (1080p) connection of 24, 25, 30, 50, and 60 Hz, and for a Component (1080p)
connection of 50 and 60Hz, only the input source is supported.
You can change the picture size simply by pressing the P.SIZE button on the remote control.
Depending on the input source, the picture size options may vary.
The items available may differ depending on the selected mode.
When Double ( , ) mode has been set in PIP, the Picture Size cannot be set.
In PC Mode, only "16:9" and "4:3" mode can be adjusted.
English - 20
Move
Picture Options
Move
Move
Picture
Enter
Enter
Size
Enter
Continued...
Exit
Return
Return
Positioning and Sizing the screen using Zoom
− Resizing the screen using the Zoom enables the positioning and sizing of the screen to up/down direction
using the ▲ or ▼ button as well as the screen size.
− Move the screen up/down using the ▲ or ▼ button after selecting the by pressing the ◄ or ► button.
− Resize the screen vertically using the ▲ or ▼ button after selecting the by pressing the ◄ or ► button.
Screen Mode: 16:9/Wide Zoom/Zoom/4:3
When setting the picture size to Auto Wide in a 16:9 wide TV,
you can determine the picture size you want to see the 4:3
WSS (Wide Screen Service) image or nothing. Each individual
European country requires different picture size so this function
is intended for users to select it.
− 16:9
: Sets the picture to 16:9 wide mode.
−
Wide Zoom: Magnify the size of the picture more than 4:3.
−
Zoom: Magnify the size of the picture vertically on screen.
− 4:3
: Sets the picture to 4:3 normal mode.
This function is available in Auto Wide mode.
This function is not available in PC,Component or HDMI mode.
Digital NR: Off/Low/Medium/High/Auto
T V
Colour Tone : Normal
Size : Auto Wide
Screen Mode : 16:9
Digital NR :
DNle :
HDMI Black Level :
Movie Plus : Low
Blue only mode : Off
Screen Burn Protection
Move
Picture Options
Enter
16:9
Wide Zoom
Zoom
4:3
If the signal received by the television is weak, you can activate this feature to reduce any static and
ghosting that may appear on the screen.
This function is not available in PC mode.
When the signal is weak, select one of the other options until the best picture is displayed.
DNIe: Off/Demo/On
This TV includes the DNIe function so as to provide a high visual quality. If you set DNIe to on, you
can view the screen with the DNIe feature activated. If you set the DNIe to Demo, you can view the
applied DNIe and normal pictures on the screen, for demonstration purposes. Using this function, you
can view the difference in the visual quality.
DNIeTM (Digital Natural Image engine)
This feature brings you more detailed image with 3D noise reduction, detail enhancement, contrast
enhancement and white enhancement. New image compensation Algorithm gives brighter, clearer, more
detailed image to you. DNIeTM technology will fit every signal into your eyes.
This function is not available in PC mode.
This function is available only in Dynamic mode.
HDMI Black Level: Normal/Low
Using this function, you can adjust the image quality when the screen burn (appearance of black
level, low contrast, low colour, etc.) is encountered by the HDMI input for RGB limited range (16 to
235).
This function is active only when the external input connects to HDMI(RGB signals).
Movie Plus: Off/Low/Medium/High/Demo
You can view more natural skin and clear text even in fast moving scenes.
This function is not available in PC mode.
The Wide Zoom, Zoom and Just Scan mode are not supported.
Blue Only Mode: Off/On
This function is for AV device measurement experts. This function displays the blue signal only by
removing the red and green signals from the video signal so as to provide a Blue Filter effect that is
used to adjust the Colour and Tint of video equipment such as DVD players, Home Theaters, etc.
Using this function, you can adjust the Colour and Tint to preferred values appropriate to the signal
level of each video device using the Red/Green/Blue/ Cyan/Magenta/ Yellow Colour Bar Patterns,
without using an additional Blue Filter.
Blue Only Mode is available when the picture mode is set to Movie or Standard.
Screen Burn Protection
To reduce the possibility of screen burn, this unit is equipped
with screen burn prevention technology. This technology
enables you to set picture movement up/down (Vertical Line)
and side to side (Horizontal Dot). The Time setting allows
you to program the time between movement of the picture in
T V
Screen Burn Protection
Pixel Shift
White
Scrolling
Side Gray : Dark
minutes.
Return
English - 21
Move
Enter
Return
Continued...
− Pixel Shift: Using this function, you can minutely move
pixels on the PDP in horizontal or vertical direction to
minimize after image on the screen.
− Set
Pixel Shift to On by pressing the ▲ or ▼ button,
then press the ENTER button.
T V
Pixel Shift
Pixel Shift :
Horizontal Dot : 2
Vertical Line : 2
Timer : 2 min
On
− Select the required option by pressing the ▲ or ▼
button, then press the ENTER button.
Available options:
Optimum condition for pixel shift;
Horizontal Dot, Vertical Line, Time
TV/Ext/AV/Component/
PC
HDMI/DTV
Move
Enter
Horizontal Dot 4 4
Vertical Line 4 4
Timer (minute) 4 4 min
The Pixel Shift value may differ depending on the monitor size (inches) and mode.
−
White: This function helps remove after images on the screen by changing the colour of pixels
to white. Use this function when there are remaining after images or symbols on the screen
especially when you displayed a still image on the screen for a long time.
−
Scrolling: This function helps remove after images on the screen by moving all the pixels on the
PDP according to a pattern. Use this function when there are remaining after images or symbols
on the screen especially when you displayed a still image on the screen for a long time.
−
Side Gray: When you watch TV with the screen ratio of 4:3, the screen is prevented from any
damage by adjusting the white balance on both extreme left and right sides.
Dark: When you set the screen ratio to 4:3, it darkens the left and right sides.
Light: When you set the screen ratio to 4:3, it brightens the left and right sides.
To remove after images on the screen, use either White or Scrolling function. Although both of
the two functions remove after images on the screen, Scrolling is more effective.
The after image removal function has to be executed for a long time (approximately 1 hour) to
effectively remove after images on the screen. If after image is not improved after the execution
of the function, repeat the function again.
Press any button on the remote control to cancel this feature.
Return
Resetting the Picture Settings to the Factory Defaults
You can set detailed picture settings.
1 Press the MENU button to display the menu.
2 Press the ENTER button to select Picture.
3 Press the ▲ or ▼ button to select Reset, then press the
ENTER button.
4 Press the ▲ or ▼ button to select OK or Cancel then press
the ENTER button.
Each mode can be reset.
English - 22
T V
More
Picture Options
Reset : OK
Move
Picture
Enter
OK
Cancel
Return
Sound Features
1 Press the MENU button to display the menu.
T V
2 Press the ▲ or ▼ button to select Sound, then press the
ENTER button.
3 Select the required option by pressing the ▲ or ▼ button, then
press the ENTER button.
Available options:
Mode, Equalizer, SRS TS XT, Auto Volume,
Mode :
Equalizer
SRS TS XT : Off
Auto Volume : Off
TV Speaker : Off
Sound Select : Main
Sound
TV Speaker, Sound Select
4 When you are satisfied with your setting, press the ENTER
button.
5 Press the EXIT button to exit.
Mode: Standard/Music/Movie/Speech/Custom
You can select the type of special sound effect to be used
when watching a given broadcast.
Easy Setting
1 Press the TOOLS button on the remote control.
Anynet+ (HDMI-CEC)
Picture Mode : Standard
SoundMode ◄ Custom ►
Sleep Timer : Off
SRS TS XT : Off
Energy Saving : Off
Dual I-II : Mono
Move
Tools
Move Adjust
Enter
2 Press the ▲ or ▼ button to select Sound Mode.
3 Press the ◄ or ► button to select the required option.
Equalizer: Balance/100Hz/300Hz/1kHz/3kHz/10kHz
The television has several settings which allow you to control
the sound quality.
If you make any changes to these settings, the sound
mode is automatically switched to Custom.
T V
R
L
Balance 100Hz 300Hz 1kHz 3kHz 10kHz
Equalizer
+
0
-
SRS TS XT: Off/On
TruSurround XT is a patented SRS technology that solves the
problem of playing 5.1 multichannel content over two speakers.
Move Adjust
TruSurround delivers a compelling, virtual surround sound experience through any two-speaker
playback system, including internal television speakers. It is fully compatible with all multichannel
formats.
TruSurround XT, SRS and Symbol are trademarks of SRS Labs, Inc.
TruSurround XT technology is incorporated under license from SRS Labs, Inc.
Custom
Return
Exit
Return
+
0
-
Easy Setting
1 Press the TOOLS button on the remote control.
2 Press the ▲ or ▼ button to select SRS TS XT.
3 Press the ◄ or ► button to select Off or On.
Anynet+ (HDMI-CEC)
Picture Mode : Standard
Sound Mode : Custom
Sleep Timer : Off
SRSTSXT ◄ Off ►
Energy Saving : Off
Dual I-II : Mono
Move Adjust
Tools
Auto Volume: Off/On
Each broadcasting station has its own signal conditions, and so it is not easy to adjust the volume
every time the channel is changed. This feature lets you automatically adjust the volume of the
desired channel by lowering the sound output when the modulation signal is high or by raising the
sound output when the modulation signal is low.
TV Speaker: Off/On
If you want to hear the sound through separate speakers, cancel the internal amplifier.
The – +, MUTE buttons do not operate when the TV Speaker is set to Off.
When TV Speaker is set to Off, you can operate only Sound Select (in PIP mode) in Sound
menu.
Sound Select: Main/Sub
When the PIP feature is activated, you can listen to you can operate only Sound Select (in PIP mode)
in Sound menu.
− Main: Used to listen to the sound of the main picture.
− Sub: Used to listen to the sound of the sub picture.
English - 23
Exit
Selecting the Sound Mode (depending on the model)
The DUAL I-II button displays/controls the processing and output of the audio signal. When power
is switched on, the mode is automatically preset to either “DUAL-I” or “Stereo”, depending on the
current transmission.
Easy Setting
1 Press the TOOLS button on the remote control.
2 Press the ▲ or ▼ button to select Dual I-II.
3 Press the ◄ or ► button to select the required option.
Type of broadcast On-screen indication
Regular broadcast
(Standard audio)
Regular + NICAM Mono NICAM
NICAM
Stereo
NICAM Stereo
Mono (Normal use)
NICAM
stereo
Mono
(Normal)
Mono
(Normal)
Anynet+ (HDMI-CEC)
Picture Mode : Standard
Sound Mode : Custom
Sleep Timer : Off
SRS TS XT : Off
Energy Saving : Off
DualI-II ◄ Mono ►
Move Adjust
Tools
Exit
NICAM DUAL-I/II
Regular broadcast
A2
Stereo
If the stereo signal is weak and automatic switching occurs, switch to Mono.
(Standard audio)
Bilingual or DUAL-I/II Dual I Dual II
Stereo Stereo
If the receiving conditions deteriorate, listening will be easier if the mode is set to Mono.
NICAM
dual-1
NICAM
dual-2
Mono (Normal use)
(Forced mono)
Mono
(Normal)
Mono
This function is only available in Analog TV mode.
Connecting Headphones (Sold separately)
You can connect a set of headphones to your set if you wish to watch a TV program without
disturbing other people in the room.
When you insert the head set jack into the corresponding
port, you can operate only “Auto Volume” and Sound
Select(in PIP mode) in Sound menu.
Prolonged use of headphones at a high volume may
damage your hearing.
You will not hear sound from the speakers when you
connect headphones to the TV.
The headphone volume and TV volume are adjusted
separately.
TV Side Panel
15
English - 24
Time Features
1 Press the MENU button to display the menu.
T V
2 Press the ▲ or ▼ button to select Setup, then press the
ENTER button.
3 Press the ▲ or ▼ button to select Time, then press the
ENTER button.
4 Select the required option by pressing the ▲ or ▼ button, then
press the ENTER button.
Available options:
Clock Set, Sleep Timer, Timer 1, Timer 2,
Timer 3
5 When you are satisfied with your setting, press the ENTER
T V
button.
6 Press the EXIT button to exit.
Clock Set
You can set the television clock so that the current time is
Plug & Play
Language : English
Time
Light Effect
Auto Wall-Mount
Melody : Off
Entertainment
Energy Saving :
PIP
Clock Set : 00 : 00
Sleep Timer : Off
Timer 1 : Inactivated
Timer 2 : Inactivated
Timer 3 : Inactivated
Move
:
: Off
Setup
In Standby
Off
Enter
Time
displayed when pressing the INFO button on the remote control.
You must also set the time if you wish to use the automatic on
or off timers.
− Press the ◄ or ► button to select
Month, Day, Year, Hour,
or Minute. Set these by pressing the ▲ or ▼ button.
You can set the Month, Day, Year, Hour, or Minute
directly by pressing the numeric buttons on the remote
control.
In the event of a power interruption or the set being turned
off at the supply, the settings for the Clock will be lost.
Sleep Timer
Anynet+ (HDMI-CEC)
Picture Mode : Standard
Sound Mode : Custom
SleepTimer ◄ Off ►
SRS TS XT : Off
Energy Saving : Off
Dual I-II : Mono
You can select a time period of between 30 and 180 minutes
after which the television automatically switches to standby
mode.
− Select the preset time interval (
180
) for staying on by pressing the ▲ or ▼ button.
Off, 30, 60, 90, 120, 150, or
T V
Easy Setting
1 Press the TOOLS button on the remote control.
2 Press the ▲ or ▼ button to select Sleep Timer.
3 Press the ◄ or ► button to select the minute, then press the
ENTER button.
Move
Tools
Move Adjust
On Time
:
00 00 Inactivate
Off Time
:
00 00 Inactivate
Volume
10
Repeat
Once
Move Adjust
Enter
Timer 1
Timer 1 / Timer 2 / Timer 3
You can set the On/Off timers so that the television will switch
on or off automatically at the time you select.
You must set the clock first.
− Press the ◄ or ► button to select the required item below.
Press the ▲ or ▼ button to adjust to the setting satisfied.
On Timer : Select hour, minute, and Inactivate/Activate. (To activate timer with the setting
satisfied, set to Activate.)
Off Timer : Select hour, minute, and Inactivate/Activate. (To activate timer with the setting
satisfied, set to Activate.)
Repeat : Select Once, Everyday, Mon~Fri, Mon~Sat, or Sat~Sun.
Volume : Select the required volume level.
You can set the hour, minute, directly by pressing the number buttons on the remote control.
Auto Power Off
When you set the timer “On”, the TV will eventually turn off, if no controls are operated for 3 hours
after the TV was turned on by timer. This function is only available in timer “On” mode and prevents
overheating, which may occur if a TV is on for too long time.
Return
Return
Exit
Return
English - 25
Language / Light Effect / Melody / Entertainment /
Energy Saving / PIP
1 Press the MENU button to display the menu.
T V
2 Press the ▲ or ▼ button to select Setup, then press the
ENTER button.
3 Select the required option by pressing the ▲ or ▼ button, then
press the ENTER button.
Available options:
Language, Melody, Light Effect,
Entertainment, Energy Saving, PIP
4 When you are satisfied with your setting, press the ENTER
button.
Plug & Play
Language : English
Time
Light Effect
Auto Wall-Mount
Melody : Off
Entertainment
Energy Saving :
PIP
Move
:
: Off
Setup
In Standby
Off
Enter
5 Press the EXIT button to exit.
Language
It is variable depending on the model. When you start using the television for the first time, you must
select the language which will be used for displaying menus and indications.
Light Effect: Off/In Standby/In Watching TV/Always
You can turn on/off the blue LED on the front of TV according to the situation. Use it for saving power
or when the LED dazzles your eyes.
−
Off: The blue LED is always off.
−
In Standby: The blue LED lights while in Standby mode and it turns off when your TV is turned on.
−
In Watching TV: The blue LED lights when watching TV and it turns off when your TV is turned off.
−
Always: The blue LED always lights.
Set the Light Effect to Off to reduce the power consumption.
Melody: Off/Low/Medium/High
The TV power on/off melody sound can be adjusted.
When the Melody does not play
When no sound is output from the TV because the MUTE button has been pressed.
When no sound is output from the TV because the – (Volume) button has been pressed.
When the TV is turned off by Timer function.
Manufactured under license from Dolby Laboratories.
Dolby and the double-D symbol are trademarks of Dolby Laboratories.
Return
Entertainment: Off/Sports/Cinema/Game
Entertainment mode enables you to select the optimal display and sound for sports, cinema and
games.
−
Off: Switches the Entertainment function off.
−
Sports: Provides the optimal picture and sound quality for sports.
− Cinema:
Provides the optimal picture and sound quality for movie watching.
You can experience a richer picture and enhanced sound.
− Game:
Provides the optimal picture and sound quality for games. This mode accelerates the
playing speed when using an external game console connected to the TV.
If you set any of the three Entertainment modes to On, the settings will be locked and can not
be adjusted. If you want to make Picture and Sound mode adjustments, the Entertainment mode
must be turned off.
The Entertainment settings are saved for each input source.
English - 26
Continued...
Energy Saving: Off/Low/Medium/High
This feature adjusts the screen brightness depending on the
surrounding lighting conditions.
−
Off: Switches off the Energy Saving mode.
−
Low: Operates in standa r d mode re g ardless of the
surrounding illumination.
−
Medium: Enters Medium power saving mode regardless of
the surrounding illumination.
−
High: Enters maximum power saving mode regardless of
the surrounding illumination.
Easy Setting
1 Press the TOOLS button on the remote control.
2 Press the ▲ or ▼ button to select Energy Saving.
3 Press the ◄ or ► button to select the required option.
PIP (Picture in Picture): PIP(On/Off)/Source/Size/Position/
Programme
You can display a sub picture within the main picture. In this
way you can watch TV programme or monitor the video input
from any connected devices.
−
PIP: On/Off
You can activate or deactivate the PIP function.
Table of PIP Settings
Anynet+ (HDMI-CEC)
Picture Mode : Standard
Sound Mode : Custom
Sleep Timer : Off
SRS TS XT : Off
EnergySaving ◄ Off ►
Dual I-II : Mono
Move Adjust
T V
T V
Tools
Exit
Move
:
: Off
Setup
In Standby
Off
Enter
PIP
Return
Plug & Play
Language : English
Time
Light Effect
Auto Wall-Mount
Melody : Off
Entertainment
Energy Saving :
PIP
PIP : On
Source : DTV
Size :
Position :
Programme : P 1
Main Picture Sub Picture
Move
Component
HDMI1, 2, 3
PC
TV, DTV, Ext1, Ext2, AV
− Source
You can select a source of the sub-picture.
−
Size: / /
You can select a size of the sub-picture.
If main picture is in PC and Component mode, Size is not available.
−
Position: / / /
You can select a position of the sub-picture.
In Double( , ) mode, Position cannot be selected.
−
Programme
You can select a channel of the sub-picture only when the Source is set to TV and DTV.
Enter
Return
English - 27
Setting up Your PC Software (Based on Windows XP)
The Windows display-settings for a typical computer
are shown below. But the actual screens on your PC will
probably be different, depending upon your particular
version of Windows and your particular video card. But even
if your actual screens look different, the same, basic set-up
information will apply in almost all cases. (If not, contact your
computer manufacturer or Samsung Dealer.)
1 Right click the mouse on the Windows Desktop, then click on
Properties.
The Display Properties will be displayed.
2 Clic k on Sett ings tab, then set the Disp lay Mode with
reference to the Display Modes Table. You do not need to
change the Colours settings.
3 Click on Advanced. A new settings dialog box will be displayed.
4 Click on the Monitor tab, then set the Screen refresh rate with reference to the Display Modes
Table. Set the Vertical Frequency and Horizontal Frequency individually if you can do so instead of
setting the Screen refresh rate.
5 Click on OK to close the window, then Click on OK button to the Display Properties window.
Automatic re-booting may commence at this moment.
English - 28
Input Mode (PC)
Both screen position and size will vary depending on the type of PC monitor and its resolution.
The table below shows all of the display modes that are supported:
D-Sub Input
Mode Resolution
IBM
VESA
CVT 1920 x 1080RB 66.587 59.934 138.500 + / -
640 x 350
720 x 400
640 x 480
640 x 480
640 x 480
800 x 600
800 x 600
800 x 600
1024 x 768
1024 x 768
1024 x 768
1280 x 1024
1280 x 1024
1360 x 768
1600 x 1200
Horizontal
Frequency
(kHz)
31.469
31.469
31.469
37.861
37.500
37.879
48.077
46.875
48.363
56.476
60.023
63.981
79.976
47.712
75.000
HDMI/DVI Input
Mode Resolution
640 x 480
800 x 600
VESA
CEA 1920 x 1080p 67.500 60.000 148.500 + / +
1024 x 768
1280 x 1024
1360 x 768
1600 x 1200
Horizontal
Frequency
(kHz)
31.469
37.879
48.363
63.981
47.712
75.000
Vertical
Frequency
(Hz)
70.086
70.087
59.940
72.809
75.000
60.317
72.188
75.000
60.004
70.069
75.029
60.020
75.025
60.015
60.000
Vertical
Frequency
(Hz)
59.940
60.317
60.004
60.020
60.015
60.000
Pixel Clock
Frequency
(MHz)
25.175
28.322
25.175
31.500
31.500
40.000
50.000
49.500
65.000
75.000
78.750
108.000
135.000
85.500
162.000
Pixel Clock
Frequency
(MHz)
25.175
40.000
65.000
108.000
85.500
162.000
Sync Polarity
(H/V)
+ / -
- / +
- / -
- / -
- / + / +
+ / +
+ / +
- / -
- / + / +
+ / +
+ / +
+ / +
+ / +
Sync Polarity
(H/V)
- / + / +
- / + / +
+ / +
+ / +
When using an HDMI/DVI cable connection, you must use the HDMI IN 2 jack.
The interlace mode is not supported.
The set might operate abnormally if a non-standard video format is selected.
Separate and Composite modes are supported. SOG is not supported.
English - 29
Setting the PC
Preset to the PC mode by pressing the SOURCE button.
1 Press the MENU button to display the menu.
2 Press the ▲ or ▼ button to select Picture, then press the
ENTER button.
3 Select the required option by pressing the ▲ or ▼ button,
then press the ENTER button.
4 When you are satisfied with your setting, press the ENTER
button.
5 Press the EXIT button to exit.
Auto Adjustment :
Auto adjustment allows the PC screen to self-adjust to the
incoming PC video signal.
The values of fine, coarse and position are adjusted
automatically.
Easy Setting
1 Press the TOOLS button on the remote control.
2 Press the ▲ or ▼ button to select Auto Adjustment, then
press the ENTER button.
Screen: Coarse/Fine/Position/Image Reset
-Coarse/Fine
The purpose of picture quality adjustment is to remove or
reduce picture noise.
If the noise is not removed by Fine-tuning alone, then adjust
the frequency as best as possible (coarse) and Fine-tune
again.
After the noise has been reduced, re-adjust the picture so that
it is aligned on the center of screen.
1 Press the ▲ or ▼ button to select Coarse or Fine, then
press the ENTER button.
2 Press the ◄ or ► button to adjust the screen quality,
vertical stripes may appear or the picture may be blurry.
Press the ENTER button.
-Position
Adjust the PC’s screen positioning if it does not fit the TV
screen.
1 Adjust the position by pressing the ▲/▼/◄/► button.
2 Press the ENTER button.
-Image Reset
You can replace all image settings with the factory default
values.
T V
Mode : Standard
Cell Light 7
Contrast 80
Brightness 45
Sharpness 50
Auto Adjustment
Screen
Detailed Settings
More
Auto Adjustment in Progress
Anynet+ (HDMI-CEC)
Picture Mode Standard
Sound Mode Custom
Sleep Timer Off
SRS TS XT Off
Energy Saving Off
PIP
Auto Adjustment
Move
T V
Coarse 50
Fine 63
Position
Image Reset
T V
Move
Please wait.
Tools
Enter
Move
Move
Picture
Enter
Screen
Enter
Position
Enter
Return
Exit
Return
Return
English - 30
Image Reset is completed.
OK
Loading...