Samsung PPM50M7HB, PPM42M7HB User Manual

Contact SAMSUNG WORLD-WIDE

If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care centre.

聯聯絡絡全全球球三三星星若舅有任何與三星産品相關的問題或建議, 請聯絡三星客戶服務中心0

Professional PDP Display (PLASMA

PPM42M7H

DISPLAY PANEL)

Country

AUSTRALIA CHINA HONG KONG INDIA INDONESIA JAPAN MALAYSIA PHILIPPINES SINGAPORE SOUTH AFRICA TAIWAN THAILAND U.A.E VIETNAM

Customer Care Centre

1300 362 603 800-810-5858, 010- 6475 1880 2862 6001 3030 8282, 1600 1100 11 0800-112-8888 0120-327-527 1800-88-9999 1800-10-SAMSUNG (7267864) 1800-SAMSUNG (7267864) 0860 7267864 (SAMSUNG) 0800-329-999 1800-29-3232, 02-689-3232 800SAMSUNG (7267864) 1 800 588 889



www.samsung.com/au www.samsung.com.cn www.samsung.com/hk www.samsung.com/in www.samsung.com/id www.samsung.com/jp www.samsung.com/my www.samsung.com/ph www.samsung.com/sg www.samsung.com/za www.samsung.com/tw www.samsung.com/th www.samsung.com/mea www.samsung.com/vn

Web Site

PPM50M7H

Owner’s Instructions

Before operating the unit,

please read this manual thoroughly,

and retain it for future reference.

Intended for Commercial Use and Operation

BN68-01304E-00

ON-SCREEN MENUS

Picture In Picture (PIP)

VIDEO WALL

MDC (Multiple Display Control)

Screen Burn Protection

SRS TruSurroundXT

■

Model ________________ ■Serial No. ________________

User Instructions

◆ Screen Image retention

Do not display a still image (such as on a video game or when hooking up a PC to this PDP Display) on the plasma PDP Display panel for more than 2 hours as it can cause screen image retention. This image retention is also known as “screen burn”. To avoid such image retention, reduce the degree of brightness and contrast of the screen when displaying a still image.

◆ Height

The PDP Display can normally operate only under 2000m in height. It might abnormally function at a place over 2000m in height, so do not install and operate there.

◆ Heat on the top of the PDP Display

The top side of the product may be hot after long periods of use as heat dissipates from the panel through the vent hole in the upper part of the product. This is normal and does not indicate any defect or operation failure of the product. However, children should be prevented from touching the upper part of the product.

◆ The product is making a ‘cracking’ noise.

A ‘cracking’ noise may occur when the product contracts or expands due to a change of surrounding environment such as temperature or humidity. This is normal and not a defect of the unit.

◆ Cell Defects

The PDP Display uses a panel consisting of 1,230,000(SD-level) to 3,150,000(HD-level) pixels which require sophisticated technology to produce. However, there may be a few bright or dark pixels on the screen. These pixels will have no impact on the performance of the product.

◆ Avoid operating the PDP Display at temperatures below 5°C(41°F)

◆ A still image displayed too long may cause permanent damage to the PDP Display Panel

Watching the PDP Display in 4:3 format for a long period of time may leave traces of borders displayed on the left, right and center of the screen caused by the difference of light emission on the screen. Playing a DVD or a game console may cause similar effect to the screen. Damage caused by the above effect are not covered by the Warranty.

◆ Afterimage on the Screen.

Displaying still images from Video games and PC for longer than a certain period of time may

produce partial afterimages.

To prevent this effect, reduce the ‘brightness’ and ‘contrast’ when displaying still images for a

long time.

◆ Warranty

- Warranty does not cover any damage caused by image retention.

- Burn-in is not covered by the warranty.

◆ Installation

Be sure to contact an authorized service center, when installing your PDP Display in a location with heavy dust, high or low temperatures, high humidity, chemical substance and where it operates for 24 hours such as the airport, the train station or etc. Failure to do so may cause a serious damage to your PDP Display. Installing the product in an airtight place may shorten the lifetime of the product.

English - 2

Checking Parts

Owner’s Instructions

Remote Control/

AAA Batteries

Ferrite Cores for

Speaker Wire (2EA)

(Refer to page 14)

Ferrite Core (Power Cord, Speaker Wire)

➢

The ferrite cores are used to shield the cables from interference. When connecting a cable, open the ferrite core and clip it around the cable near the plug.

Ferrite Core for

Power Cord

PC Cable

Stand-Base

(2EA)

Screws

(4EA)

English - 3

◆ FOREWORD

■ User Instructions............................................................................................ 2

◆ CONNECTING AND PREPARING YOUR DISPLAY

■ Control Panel................................................................................................. 6

■ Infrared Remote Control ................................................................................ 8

■ Inserting the Batteries in the Remote Control................................................ 9

■ Assembling the Stand-Base .......................................................................... 9

■ Installing the Display on the Wall Attachment Panel ..................................... 10

■ Installing the Display Vertically ...................................................................... 12

■ Before Using the Video Wall and the Multiple Display Control function ........ 12

■ Connecting Speakers .................................................................................... 13

■ Switching Your PDP Display On and Off....................................................... 15

■ Choosing Your Language.............................................................................. 15

◆ USING YOUR DISPLAY

■ Changing the Picture Standard ..................................................................... 16

■ Customizing the Picture Settings................................................................... 17

■ Adjusting the RGB Color (PC Mode) ............................................................. 18

■ Setting the Picture (PC Mode)....................................................................... 18

■ Using Zoom function (PC Mode) ................................................................... 20

■ Selecting the Picture Size.............................................................................. 21

■ Freezing the Current Picture ......................................................................... 22

■ Changing the Sound Standard ...................................................................... 22

■ Customizing the Sound Settings ................................................................... 23

■ Setting the TruSurround XT........................................................................... 24

■ Activating Panel Button Lock......................................................................... 25

■ Activating Remote Control Button Lock......................................................... 26

■ Setting Up Your Personal ID Number............................................................ 27

English - 4

Continued...

Contents

◆ USING YOUR DISPLAY (CONTINUED)

■ Setting the MDC (Multiple Display Control) ................................................... 28

■ Preventing Screen Burn-in ............................................................................ 29

■ Reducing the Effects of Screen Burn ............................................................ 30

■ Setting the Screen Burn Protection Timer ..................................................... 31

■ Setting the Multiple Screen............................................................................ 32

■ Displaying the Setting Information................................................................. 33

■ Setting and Displaying the Current Time....................................................... 33

■ Switching the PDP Display On and Off Automatically ................................... 34

■ Selecting the Fan........................................................................................... 36

■ Viewing the Picture in Picture (PIP)............................................................... 37

■ Viewing an External Signal Source ............................................................... 38

◆ ADDITIONAL INFORMATION AND CONNECTIONS

■ Connecting to the Audio/Video Input............................................................. 39

■ Connecting to the S-Video Input.................................................................... 40

■ Connecting to the Component Input.............................................................. 40

■ Connecting to the DVD/DTV Receiver Input ................................................. 41

■ Connecting to the DVI Input .......................................................................... 41

■ Connecting to the PC Input ........................................................................... 42

■ Setting up Your PC Software (Windows only) ............................................... 43

■ Input Mode (PC/DVI) ..................................................................................... 44

■ Power Saver (PC1 mode only) ...................................................................... 45

◆ RECOMMENDATIONS FOR USE

■ Troubleshooting: Before Contacting Service Personnel................................ 46

■ Technical Specifications ................................................................................ 47

Symbols

Press Important Note

☛

➢

English - 5

Control Panel

➢

Front of the PDP Display

The actual configuration of your PDP Display may be different, depending on your model.

Speaker

(Optional)

SOURCE

- Select the external input source.

- Store your settings in the menu.

- When the Main menu is displayed on screen, the Main menu is not operated with source key.

Display the on-screen menu.

VOL +

- Adjust the volume.

- Adjust an option value respectively.

VOL + : Enter to the selected menu.)

(

SEL

Control the cursor in the menu.

I /

Press to turn the PDP Display on and off.

Speaker

(Optional)

a b c

Power Indicator

- Power Off; Black

- Power On; Green

Remote Control Sensor

Aim the remote control towards this spot on the PDP Display.

➢

English - 6

◆ You can use the mode depending on the model.

◆ The VOL on the remote control.

◆ If the remote control no longer works or you have misplaced it, you can use the controls on the panel of the PDP Display.

-,+ and

SEL ,

buttons to switch on the PDP Display when it is in standby

buttons have the same function as the ▲/▼/œ/√ buttons

Continued...

Rear Panel

a) POWER IN

Connect the supplied power cord.

b) EXT SPEAKER (8Ω)

Connect external speakers.

c) DVI/PC AUDIO IN

Connect to the audio output jack on your PC or DVI.

AUDIO is an audio input jack for PC1 and PC2

➢

modes.

d) DVI IN

Connect to the video output jack for device with DVI output.

e) PC IN1/PC OUT1

PC IN1 : Connect to the video output jack on

your PC.

PC OUT1 : Connect to the video input jack on

external devices.

f) PC IN2 (BNC)

Connect for RGB HV video signal input from the PC.

“PC Mode” from this page onward means

➢

PC1/PC2 mode using

RGB2(PC2).

RGB1(PC1) and

g) RS-232C

IN : Used for the MDC function when connecting

PC or RS-232C output of another PDP Display.

OUT : Used for the MDC function when

connecting with RS-232C input of another PDP Display.

For further details about connections, refer to

➢

Page 12.

h) COMPONENT IN

Video (Y/PB/PR) and audio (L/R) inputs for component.

i) AV (VIDEO/AUDIO L/R)

IN : Video and audio inputs for external devices,

such as a camcorder or VCR.

OUT : Outputs for external devices.

j) S-VIDEO IN

Video input for external devices with an S-Video output, such as a camcorder or VCR.

For further details about connection, refer to pages 39~42.

➢

Whenever you connect an audio or video system to your PDP Display, ensure that all elements are

➢

switched off. Refer to the documentation supplied with your equipment for detailed connection instructions and associated safety precautions.

English - 7

Infrared Remote Control

PDP DISPLAY ON

DIRECT CHANNEL SELECTION

PDP DISPLAY OFF

NOT AVAILABLE

VOLUME INCREASE

TEMPORARY SOUND SWITCH-OFF

VOLUME DECREASE

SETTING THE TIMER

MENU DISPLAY

MOVE TO THE REQUIRED MENU

ADJUST AN OPTION VALUE

PICTURE EFFECT SELECTION

AUTO ADJUSTMENT IN PC MODE

- PIP ACTIVATION OR DEACTIVATION

- SOURCE SELECTION (SOURCE)

OPTION/

RESPECTIVELY

PIP FUNCTIONS:

(PIP)

PICTURE STILL

NEXT CHANNEL

EXTERNAL INPUT SELECTION

PREVIOUS CHANNEL

INFORMATION DISPLAY

EXIT FROM ANY DISPLAY

CONFIRM YOUR CHOICE (STORE OR ENTER)

SOUND EFFECT SELECTION

PICTURE SIZE

ULTIPLE DISPLAY CONTROL

SCREEN EFFECT SELECTION (BURNING PROTECTION)

English - 8

The performance of the remote control may be affected by bright light.

➢

Inserting the Batteries in the Remote Control

You must insert or replace the batteries in the remote control when you:

◆ Purchase the PDP Display

◆ Find that the remote control is no longer operating

correctly

1 Remove the cover on the rear of the remote control by pressing

the symbol ( ) downwards and then pulling firmly to remove it.

2 Insert two R03, UM4, “AAA” 1.5V or equivalent batteries taking

care to respect the polarities:

◆-on the battery against -on the remote control

◆+on the battery against +on the remote control

3 Replace the cover by aligning it with the base of the remote

control and pressing it back into place. Do not mix battery types, i.e. alkaline and manganese.

Assembling the Stand-Base

1 Assemble the PDP Display with the stand and firmly

secure the PDP Display using 4 screws provided.

Two or more people should carry the PDP Display.

➢

Never lay the PDP Display on the floor because of possible damage to the screen. Always store the PDP Display upright.

English - 9

Installing the Display on the Wall Attachment Panel

Refer to the correct installation guide according to your wall bracket.

➢

Installation Notes

◆

Contact a technician for installing the wall bracket.

◆

Samsung Electronics is not responsible for any damages to the product or harm to customers when the installation is done by the customer.

◆

This product is for installing on cement walls. The product may not stay in place when installed on plaster or wood.

Components

◆

Only use the components and accessories shipped with the product.

Wall Bracket

1 Left: 1 Right: 1

Hinge

Wall Bracket Assembly

1 Insert and tighten the Captive Screw in

the direction of the arrow. When done, mount the wall bracket on the wall.

Captive Screw

Hinge (Left)

There are two hinges (left and right). Use the correct one.

Wall Bracket

Hinge (Right)

Accessories

Plastic Hanger: 4 Screw : 11

Screw : 4

Anchor : 11

2 Before drilling into the wall, check if the length

between the two locking holes at the back of the product is correct. If the length is too short or long, loosen all or some of the 4 screws on the wall bracket to adjust the length.

Length between the two locking holes

3 Check the installation diagram and mark the drill

points on the wall. Use the 5.0 mm bit to drill holes deeper than 35 mm. Fix each anchor in the corresponding hole. Match each of the brackets and hinge holes to the corresponding anchor holes and insert and tighten the 11 screws .

Continued...

English - 10

To mount the product on the wall bracket

◆ The shape of the product may vary depending on the model. (The assemblies of the plastic hanger and the screw are the same)

1 Remove the 4 screws on the back of the product.

3 Tighten the 4 screws in step 2 (plastic hanger

+ screw ) to the rear holes of the product.

2 Insert the screw into the plastic hanger.

(See the figure below)

◆ Mount the product on the wall bracket

☛

Remove safety pin (#) and insert the 4 product holders into the corresponding bracket holes ( place the product ( bracket. Make sure to reinsert and tighten the safety pin (

PDP Display

and make sure it is properly fixed to the left and right plastic hangers.

◆ Be careful when installing the product on the bracket as fingers can be caught in the holes.

◆ Make sure the wall bracket is securely fixed to the wall, or the product may not stay in place after installation.

!). Then

@) so that it is firmly fixed to the

#) to securely hold the product to the bracket.

Wall Bracket Angle Adjustment

Adjust the bracket angle to -

➢

1 Fix the product to the wall bracket.

2 Hold the product at the top in the center and pull it

forward (direction of the arrow) to adjust the angle. (See the figure to the right)

3 You can adjust the bracket angle between -2° and 15°.

2obefore installing it on the wall.

Wall Bracket

Make sure to use the top center, and not the left or the right side of the product to adjust the angle.

Wall

English - 11

Installing the Display Vertically

❋

Samsung shall not be liable for damages caused by installing the product at the different direction from the figure below.

Before Using the Video Wall and the Multiple Display Control function

1 Please create ID for each PDP Display before

installing them close together. It may be difficult to create IDs when operating the remote control for PDPs that are installed close to each other.

You can install the PDP Display vertically. In this case, the fan automatically works. If you wish to stop the fan, position the PDP Display horizontally and then set “ in the “

Function” menu.

Please use the wall attachment panel exclusively when installing vertically. And you have to put the bottom of the PDP Display with menu buttons on the left when viewed from front.

Example for 2x2 Video Wall function

Fan” to “Off ”

2 For details about Video Wall configuration and

operation, refer to “Setting the Multiple Screen” on page 32.

Example for 2x2 Video Wall connections

Rear of the PDP Display Rear of the PDP Display

②

①

◆ You can connect a Composite (Video) without

➢

a distributor as you would connect a PC.

◆ Select ID input on the menu. Use the numeric buttons to enter the ID for PDP Display adjustment. You can operate the remote control only for the PDP Display that has been selected.

◆ For details about Multiple Display Control, refer to “Setting the MDC (M on page 28.

ultiple Display Control)”

Example for Multiple Display Control connections

English - 12

Connecting Speakers

Speakers are optional. You have to purchase the speakers

➢

additionally.

1 Remove the screws on the rear of the PDP Display.

PPM42M7H PPM50M7H

2 Hang the two “T” shaped hangers

on the square holes on the rear of the PDP Display.

3 Tighten the PDP Display and the speaker bracket using the screws removed from the PDP Display.

PPM42M7H PPM50M7H

When moving your PDP Display, do NOT hold the speaker connected to your PDP Display. It may

➢

damage the bracket clamping the speaker and your PDP Display together and result in a drop of your PDP Display and a risk of personal damage and injury.

Continued...

English - 13

Connect the speaker audio cable to the external speaker output jack on the rear of the PDP Display matching the “+” and “

◆ The speakers MUST have a power handling capability of 10 watts minimum (impedance 8Ω).

➢

◆ When you connect the speaker wire to the external speaker out connector, first bind the

” ends of the cable with the diagram on the PDP Display.

speaker wire round the ferrite core to secure it.

English - 14

Ferrite Cores

The ferrite cores are used to attenuate undesired signals. When connecting cables, attach one of these ferrite cores to the cable near the connector.

Switching Your PDP Display On and Off

The mains lead is attached to the rear of your PDP Display.

1 Plug the mains lead into an appropriate socket.

Result

: The Standby indicator on the front of the PDP Display

lights up.

The main voltage is indicated on the rear of the PDP

➢

Display and the frequency is 50 or 60Hz.

2 Press the “ ” button on the front of the PDP Display (or the ON

() button on the remote control) to switch the PDP Display on.

3 To switch your PDP Display off, press the “ ” button again (or

the

OFF () button on the remote control).

Choosing Your Language

Front of the PDP Display

When you start using your PDP Display for the first time, you must select the language which will be used for displaying menus and indications.

1 Press the MENU ()button.

: The main menu is displayed.

Result

2 Press the … or † button to select Setup.

: The Setup menu is displayed.

Result

3 Press the ENTER () button.

4 Press the … or † button to select Language.

Press the Result

ENTER () button.

: The available languages are listed.

5 Select the appropriate language by pressing the … or † button.

Press the

ENTER () button.

6 Press the EXIT button to exit.

Setup

Time

Language : English

Move Enter Return

Setup

Time

Language : English

Move Enter Return

English - 15

English

Français

Deutsch

Italiano

Español

Português

††

Changing the Picture Standard

You can select the type of picture which best corresponds to your

Picture

Mode : Dynamic

Color Control

Size : 16:9

PIP

Move Enter Return

viewing requirements.

1 Press the MENU ()button.

: The main menu is displayed.

Result

2 Press the … or † button to select Picture.

Result

3 Press the ENTER () button.

Result

The

Picture menu is displayed.

The

Mode is selected.

Mode

Mode : Dynamic Contrast 100 Brightness 50 Sharpness 75 Color 55

Tint G 50 R 50

Color Tone : Cool1 Reset

Move Enter Return

Mode

Mode : Dynamic

Contrast 100 Brightness 50 Sharpness 75 Color 55

Tint G 50 R 50

Color Tone : Cool1 Reset

Move Enter Return

Dynamic

Standard

Movie

Custom

4 Press the ENTER () button again.

Result

The

Mode menu is displayed.

5 Press the ENTER () button.

Result

: The following

options

are available.

Dynamic - Standard - Movie - Custom

6 Select the required option by pressing the … or † button.

7 Press the ENTER () button.

8 Press the EXIT button to exit.

You can also set these options simply by pressing the

➢

P.MODE (Picture Mode) button on the remote control.

English - 16

Customizing the Picture Settings

Your PDP Display has several setting options that allow you to control the picture quality.

1 Press the MENU ()button.

Result

: The main menu is displayed.

2 Press the … or † button to select Picture.

Result

The

Picture menu is displayed.

Picture

Mode : Dynamic

Color Control

Size : 16:9

PIP

3 Press the ENTER () button.

Result

The

Mode is selected.

4 Press the ENTER () button again.

Result

The

Mode menu is displayed.

5 Press the ENTER () button.

Result

: The following

options

are available.

Dynamic - Standard - Movie - Custom

6 Select the required option by pressing the … or † button.

7 Press the ENTER () button.

8 Select the required option by pressing the … or † button.

Result

: The following

options

are available.

◆ Contrast - Brightness - Sharpness - Color Tint (NTSC only)

◆ Contrast - Brightness - Color : PC or DVI Mode.

9 Press the ENTER () button.

Result

: The horizontal bar is displayed.

Press the setting.

◆ Press the … or † button to select other option(s).

➢

◆ The settings values may vary depending on the input

source. (ex. AV, Component, PC, or DVI.)

œ or √ button until you reach the optimal

Move Enter Return

Mode

Mode : Dynamic Contrast 100 Brightness 50 Sharpness 75 Color 55

Tint G 50 R 50

Color Tone : Cool1 Reset

Move Enter Return

Contrast 100

Mode

Mode : Dynamic Contrast 100 Brightness 50 Sharpness 75 Color 55

Tint G 50 R 50

Color Tone : Cool 1

Reset

Move Enter Return

Cool2

Cool1

Normal

Warm1

Warm2

10 Press the MENU () button to return to Mode menu.

Press the Press the

… or † button to select Color Tone.

ENTER () button.

11 Select the required option by pressing the … or † button.

Result

: The following

options

are available.

Cool2 - Cool1 - Normal - Warm1 - Warm2

12 Press the ENTER () button.

13 To return the factory defaults, select Reset by pressing the … or

† button. Press the ENTER () button. Result

: The previously adjusted settings will be reset to the

factory defaults.

The reset function is set for each mode (Dynamic,

➢

Standard, Movie, or Custom).

The reset function is also set for each Color Tone (Cool2,

➢

Cool1, Normal, Warm1, or Warm2).

14 Press the EXIT button to exit.

Mode

Mode : Dynamic Contrast 100 Brightness 50 Sharpness 75 Color 55

Tint G 50 R 50

Color Tone : Cool1 Reset

Move Enter Return

English - 17

Adjusting the RGB Color (PC Mode)

Preset to the PC mode by pressing the SOURCE button.

➢

Picture

Mode : Dynamic

Color Control

Size : 16:9

PIP

Move Enter Return

Color Control

Red 50

Green 50

Blue 50

Move Enter Return

Red 50

1 Press the MENU ()button.

Result

: The main menu is displayed.

2 Press the … or † button to select Picture.

Result

: The Picture menu is displayed.

3 Press the ENTER () button.

4 Press the … or † button to select Color Control.

Press the

ENTER () button.

5 Select the required option (Red, Green, or Blue) by pressing the

… or † button.

6 Press the ENTER () button.

Result

: The horizontal bar is displayed.

Press the

œ or √ button until you reach the optimal

setting.

Press the … or † button to select other option(s).

➢

7 Press the ENTER () button.

8 Press the EXIT button to exit.

Setting the Picture (PC Mode)

Preset to the PC mode by pressing the SOURCE button.

➢

Setup

Time

Language : English

Move Enter Return

Image Lock

Position

Auto Adjustment Image Reset Zoom

Move Enter Return

English - 18

1 Press the MENU ()button.

2 Press the … or † button to select Setup.

3 Press the ENTER () button.

4 Press the … or † button to select PC.

5 Press the ENTER () button to select Image Lock.

Result

: The main menu is displayed.

Result

: The Setup menu is displayed.

Press the

Result

ENTER () button.

: The PC menu is displayed.

Continued...

6 Press the … or † button to select the option (Coarse or Fine) to

be adjusted. Press the

Result

: The horizontal bar is displayed.

Press the setting.

Press the … or † button to select other option(s).

➢

ENTER () button.

œ or √ button until you reach the optimal

Image Lock

Coarse 50

Fine 30

7 Press the ENTER () button.

8 Press the MENU ()button.

: The PC menu is displayed again.

Result

9 Press the … or † button to select Position.

Press the

ENTER () button.

10 Adjust the position by pressing the …, †, œ, or √ button.

11 Press the ENTER () button.

12 Press the … or † button to select Auto Adjustment.

Press the

Result

ENTER () button.

: The screen quality and position are automatically reset.

The settings are all finished, and the PDP Display will automatically return to the previous picture.

13 To return the factory defaults, select Image Reset by pressing

the

… or † button. Press the ENTER () button.

Result

: The previously adjusted settings will be reset to the

factory defaults.

14 Press the EXIT button to exit.

Move Enter Return

Coarse 50

Position

Move Enter Return

Auto Adjustment in Progress

Please wait.

Image Reset is completed.

Return

English - 19

Using Zoom function (PC Mode)

Preset to the PC mode by pressing the SOURCE button.

➢

Setup

Time

Language : English

1 Press the MENU ()button.

Result

2 Press the … or † button to select Setup.

Result

3 Press the ENTER () button.

: The main menu is displayed.

: The Setup menu is displayed.

Move Enter Return

Image Lock

Position

Auto Adjustment Image Reset Zoom

Move Enter Return

Zoom

Zoom : 0

Position

Reset

Move Enter Return

Zoom : 1

Position

Reset

Zoom

4 Press the … or † button to select PC.

Press the

Result

ENTER () button.

: The PC menu is displayed.

5 Press the … or † button to select Zoom.

Press the

ENTER () button.

6 Press the ENTER () button again.

Select the required option by pressing the

Result

: The following options are available.

0 - 1 - 2 - 3 - 4 - 5 - 6

◆ Option 0 represents a normal screen.

➢

The greater the number, the more magnified the screen.

◆ You can select the position and reset functions by selecting options 1 through 6. (If you select option 0, the position and reset functions are not selected.)

◆ If you have selected the Zoom function as between 1~6, you will not be able to select the Auto Adjustment function.

… or † button.

7 Press the ENTER () button.

8 Press the … or † button to select Position.

Press the

ENTER () button.

9 Adjust the position by pressing the …, †, œ, or √ button.

10 Press the MENU () button.

Result

: The Zoom menu is displayed again.

Move Enter Return

Zoom

Zoom : 1

Position

Reset

Move Enter Return

English - 20

11 To return the factory defaults, select Reset by pressing the … or

† button. Press the ENTER () button.

Result

: The previously adjusted settings will be reset to the

factory defaults.

12 Press the EXIT button to exit.

Selecting the Picture Size

You can select the picture size which best corresponds to your viewing requirements.

1 Press the MENU ()button.

Result

: The main menu is displayed.

2 Press the … or † button to select Picture.

Result

: The Picture menu is displayed.

3 Press the ENTER () button.

4 Press the … or † button to select Size.

Press the

5 Select the required option by pressing the … or † button.

Result

◆ 16:9 : Sets the picture to 16:9 wide mode.

◆ Wide 4:3 : Magnify the size of the picture more than 4:3.

◆ Zoom : Magnify the size of the picture vertically on

◆ 4:3 : Sets the picture to 4:3 normal mode.

6 Press the ENTER () button.

7 Press the EXIT button to exit.

ENTER () button.

: The following options are available.

Move the screen up/down using the button after selecting the by pressing the √ or ENTER ()button.

screen.

… or †

Picture

Mode : Dynamic

Color Control

Size : 16:9

PIP

Move Enter Return

Size

16:9

Wide 4:3

Zoom

4:3

Move Enter Return

PC to DVI Mode

Size

16:9

Wide 4:3

Zoom

4:3

◆ You can select these options simply by pressing the P.SIZE

➢

button on the remote control.

◆ If you change the picture size when PIP is On, PIP will automatically be turned Off.

◆ Depending on the input source, the P.SIZE options may vary.

◆ PC and DVI modes, only 16:9 & 4:3 modes can be selected.

Positioning and Sizing the screen using Zoom

◆ Resizing the screen using the Zoom enables the positioning

➢

and sizing of the screen to up/down direction using the † button as well as the screen size.

◆ Move the screen up/down using the … or † button after selecting the by pressing the

œ or √ button.

◆ Resize the screen vertically using the … or † button after selecting the by pressing the (Pressing the

… button extends it upward and pressing the

œ or √ button.

† button extends it downward.)

◆ Screen enlargement operates only in Video/S-Video/ Component input modes.

◆ PC/DVI modes prevent the screen enlargement function.

Move Enter Return

… or

English - 21

Freezing the Current Picture

You can freeze the picture when watching a moving picture simply by pressing the “STILL” button. To return to normal viewing, press it again.

In PIP mode, Still function will be applied to the main and

➢

sub picture at the same time.

Changing the Sound Standard

You can select the type of special sound effect to be used when

Sound

Mode : Custom

Equalizer

SRS TS XT : Off

watching a given broadcast.

1 Press the MENU ()button.

Result

: The main menu is displayed.

Move Enter Return

Sound

Mode : Custom

Equalizer

SRS TS XT : Off

Move Enter Return

Standard

Music

Movie

Speech

Custom

2 Press the ▲ or ▼ button to select Sound.

Result

: The Sound menu is displayed.

3 Press the ENTER () button.

Result

: The Mode is selected.

4 Press the ENTER () button again.

Select the required option by pressing the

Result

: The following options are available.

Standard - Music - Movie - Speech - Custom

5 Press the ENTER () button.

6 Press the EXIT button to exit.

You can select these options by simply pressing the

➢

S.MODE (Sound Mode) button on the remote control.

▲ or ▼ button.

English - 22

Customizing the Sound Settings

Your PDP Display has several settings which allow you to control the sound quality.

1 Press the MENU ()button.

Result

: The main menu is displayed.

2 Press the … or † button to select Sound.

Result

The

Sound menu is

3 Press the ENTER () button.

displayed.

Sound

Mode : Custom

Equalizer

SRS TS XT : Off

Move Enter Return

4 Press the … or † button to select Equalizer.

Press the

Result

ENTER () button.

The

Equalizer menu is

displayed.

5 Select the required option (balance or equalizer) by pressing the

œ or √ button.

6 Press the … or † button until you reach the

Press the

ENTER () button.

optimal

setting.

7 Press the EXIT button to exit.

If you make any changes to the sound settings, the sound

➢

standard is automatically switched to

Custom.

Equalizer

Balance

100Hz 300Hz 1KHz 3KHz 10KHz

Move Adjust Return

English - 23

Setting the TruSurround XT

TruSurround XT is a patented SRS technology that solves the

Sound

Mode : Custom

Equalizer

SRS TS XT : Off

Move Enter Return

Sound

Mode : Custom

Equalizer

SRS TS XT : Off

Move Enter Return

Off

problem of playing 5.1 multichannel content over two speakers. TruSurround delivers a compelling, virtual surround sound experience through any two-speaker playback system, including internal PDP Display speakers. It is fully compatible with all multichannel formats.

1 Press the MENU ()button.

2 Press the … or † button to select Sound.

3 Press the ENTER () button.

4 Press the … or † button to select SRS TS XT.

5 Select Off or On by pressing the … or † button.

6 Press the EXIT button to exit.

Result

: The main menu is displayed.

Result

The

Sound menu is

Press the ENTER () button.

Press the

ENTER () button.

displayed.

English - 24

Activating Panel Button Lock

This feature allows you to lock the PDP Display panel buttons so that it cannot be operated via the PDP Display panel. It can, however, still be operated via the remote control. Only remote control can release the panel lock setting, so keep the remote control away from unauthorized users.

1 Press the MENU ()button.

Result

: The main menu is displayed.

2 Press the ▲ or ▼ button to select Function.

Result

The

Function

3 Press the ENTER () button.

4 Press the ▲ or ▼ button to select Safety Lock.

Press the

ENTER () button.

5 Press the ENTER () button again to select Key Lock.

6 Select Off or On by pressing the ▲ or ▼ button.

Press the

ENTER () button.

7 Press the EXIT button to exit.

menu is

displayed.

Function

Screen Burn Protection

Safety Lock

Multi Control

Video Wall

Fan : Off

Move Enter Return

Safety Lock

Key Lock : Off

IR Lock

Change PIN

Move Enter Return

Safety Lock

Key Lock : Off

IR Lock

Change PIN

Off

Move Enter Return

English - 25

Activating Remote Control Button Lock

This feature allows you to lock the remote control so that it cannot

Function

Screen Burn Protection

Safety Lock

Multi Control

Video Wall

Fan : Off

be operated via the remote control. It can, however, still be operated via the PDP Display Panel buttons.

1 Press the MENU ()button.

Result

: The main menu is displayed.

Move Enter Return

Safety Lock

Key Lock : Off

IR Lock

Change PIN

Move Enter Return

IR Lock : On

2 Press the ▲ or ▼ button to select Function.

Result

The

Function

menu is

displayed.

3 Press the ENTER () button.

4 Press the ▲ or ▼ button to select Safety Lock.

Press the

ENTER () button.

5 Press the ▲ or ▼ button to select IR Lock.

Press the

ENTER () button.

6 Press the EXIT button to exit.

When IR Lock is set to On, you will not be able to use the

➢

remote control even if the remote control button is pressed. To unlock the Remote Control Button Lock, enter the PIN using the numeric keys on the remote control. ‘IR LOCK : OFF’ will appear. The default PIN is “0000”. You can set the PIN in the “Change PIN” menu.

English - 26

Setting Up Your Personal ID Number

This feature sets viewing restrictions and prevents unauthorized access to your PDP Display through the PIN (Personal Identification Number), which is a 4 digit number.

1 Press the MENU ()button.

Result

: The main menu is displayed.

Function

Screen Burn Protection

Safety Lock

Multi Control

Video Wall

Fan : Off

2 Press the ▲ or ▼ button to select Function.

Result

The

Function

menu is

displayed.

3 Press the ENTER () button.

4 Press the ▲ or ▼ button to select Safety Lock.

Press the

ENTER () button.

5 Press the ▲ or ▼ button to select Change PIN.

Press the

ENTER () button.

6 Press the number buttons to enter your current 4-digit pin number.

The default pin number for a new PDP Display set is “0000”.

➢

7 Press the numeric buttons to enter your new 4-digit pin number.

Re-enter your new pin number to confirm.

8 Press the EXIT button to exit.

If you forget the pin number, press the remote control

➢

buttons in the following sequence, which resets the pin to 0-0-0-0: MUTE, 1, 8, 6.

Move Enter Return

Safety Lock

Key Lock : Off

IR Lock

Change PIN

Move Enter Return

Change PIN

Enter PIN

Enter New PIN

0 .. 9: Enter PIN Return

Change PIN

Enter PIN

****

Enter New PIN

0 .. 9: Enter PIN Return

English - 27

Setting the MDC (Multiple Display Control)

This function enables you to easily control the connected PDP

Function

Screen Burn Protection

Safety Lock

Multi Control

Video Wall

Fan : Off

Move Enter Return

Displays on the PC by specifying IDs to connected PDP Displays.

1 Press the MENU ()button.

Result

: The main menu is displayed.

2 Press the ▲ or ▼ button to select Function.

Result

The

Function

3 Press the ENTER () button.

menu is displayed.

Multi Control

ID Setup : 00

ID Input :

Move Enter Return

ID Setup :

ID Input :

Move Enter Return

ID Setup : 00

ID Input :

0 .. 9: Enter ID Input Number

Multi Control

4 Press the ▲ or ▼ button to select Multi Control.

5 Press the ENTER () button.

Result

: The Multi Control menu is displayed with t

Setup

selected.

6 Press the ENTER () button again.

Select the ID setup number by using the numeric buttons. Press the

ENTER () button.

7 Press the ▲ or ▼ button to select ID Input.

Press the

ENTER () button.

8 Enter ID input number by using the numeric buttons.

9 Press the EXIT button to exit.

To operate the multi control function, PDP1 and PDP2

➢

should be set in the ID Setup mode. When entering the ID Input number of PDP1 while the PDP Display is set in the ID Input mode, only PDP1 is switched to the Menu screen and you can operate the remote control. At this time, PDP2 doesn't operate with the remote control and displays the standby mode of ID Input.

For further details, refer to the MDC program guide.

➢

You can select these options by simply pressing the MDC

➢

(Multiple Display Control) button on the remote control.

English - 28

Preventing Screen Burn-in

To reduce the possibility of screen burn, this unit is equipped with screen burn prevention technology. This technology enables you to set picture movement up/down (Vertical Line) and side to side (Horizontal Dot). The Time setting allows you to program the time between movement of the picture in minutes.

1 Press the MENU ()button.

Result

: The main menu is displayed.

2 Press the … or † button to select Function.

Result

: The Function menu is displayed.

3 Press the ENTER () button.

4 Press the … or † button to select Screen Burn Protection.

Press the

Result

5 Press the ENTER () button again.

Result

➢

6 Press the ENTER () button.

Select move per regular hour and preventing the residual image. Press the

➢

7 Select the required option (Horizontal Dot, Vertical Line, or

Time) by pressing the … or † button.

Press the ENTER () button.

8 Press the … or † button until you reach the optimal setting.

Press the ENTER () button.

➢

ENTER () button.

: The Screen Burn Protection menu is displayed

with the

Pixel Shift selected.

: The Pixel Shift menu is selected.

You can select these options by simply pressing the S.EFFECT button on the remote control.

On by pressing the … or † button for making the screen

ENTER () button.

Pixel Shift: Using this function, you can minutely move pixels on the PDP in horizontal or vertical direction to prevent after image on the screen.

Optimum condition for pixel shift;

Function

Screen Burn Protection

Safety Lock

Multi Control

Video Wall

Fan : Off

Move Enter Return

Screen Burn Protection

Pixel Shift

All White

Signal Pattern

Inverse

Bar

Bar & Inverse

Timer

Move Enter Return

Pixel Shift

Pixel Shift : Off

Horizontal Dot : 4

Vertical Line : 4

Time : 4 min.

Move Enter Return

Pixel Shift : On

Horizontal Dot : 4

Vertical Line : 4

Time : 4 min.

Move Enter Return

Off

Pixel Shift

PPM42M7H

Horizontal Dot

Vertical Line

Time

4 min.

9 Press the EXIT button to exit.

PPM50M7H

4 min.

English - 29

+ 66 hidden pages