Samsung PPM42S3 Owner’s Manual

PPM42S3 PPM50H3 PPM63H3

Owner's instructions

Before operating the unit,

please read this manual thoroughly,

and retain it for future reference.

Intended for ¢ommerclal Useand Operation

ON-SCREEN MENUS

PICTURE IN PICTURE (PIP)

VIDEO WALL

MDC (MULTIPLE DISPLAY CONTROL)

Thank You for Choosing Samsung!

Thank you for choosing Samsung! Your new Samsung product represents the latest in PDP

technology. We designed it with easy-to-use on-screen menus, making it one of the best

products in its class. We are proud to offer you a product that will provide convenient,

dependable service and enjoyment for years to come.

Warning[ important Safety instructions ]

The lightning flash and arrow

head within the triangle is a warning sign alerting you of "dangerous voltage" inside the product.

CAUTION:TO PREVENTELECTRICALSHOCK,DONOT [he exclamation point within /_

REMOVEREARCOVER,NO USERSERVICEABLEPARTS tile triangle is a warning sign iNSiDE. REFERSERViCiNGTO QUALiFiEDSERVICE alerting you of important PERSONNEL. instru(tions accompanying

the product.

Note to CATV system installer: This reminder is provided to call CATV system installer's attention to Article 820-

40 of the National Electrical Code (Section 54 of Canadian Electrical Code, Part I), that provides guidelines for

proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of

the building as close to the point of cable entry as practical.

Caution: FCC/CSA regulations state that any unauthorized changes or modifications to this equipment may void the user's authority to operate it.

Caution: To prevent electric shock, match the wide blade of plug to the wide slot, and fully insert the plug.

Attention: pour eviter tes chocs electriques, introduire la tame te plus large de la fiche dans ta borne correspondante de ta prise et pousser jusqu'au fond.

Important: One Federal Court has held that unauthorized recording of copyrighted TV programs is an infringement of U.S. copyright laws.Certain Canadian programs may also be copyrighted and any unauthorized recording in whole or in part may be in violation of these rights.

TO PREVENT DAMAGE WH[cH MAY RESULT iN FiRE OR ELEcTRiC SHOCK HAZARD, DO NOT

EXPOSE THiS APPLiANcE TO RAIN OR MOISTURE.

ili!i!!i,,

important Safety inforrnations (UL1492)

• Read all safety and operating instructions before operating your PDP.

• Keep the safety and operating instructions for future reference.

• Heed all warnings on the PDP and in the operating instructions.

Follow all operating and use instructions.

• Unplug the PDP from the wall outlet before cleaning. Use a damp cloth; do not use liquid or aerosol cleaners.

Never add any attachments and/or equil)ment without apl)roval of the manufacturer. Such additions

can increase the risk of fire, electric shock, or other i)ersonal injury.

[Do not use the PDP where contact with or immersion in water is a possibility, such as near bath tubs,

sinks, washing machines, swimming pools, etc.

Do not place the PDP on an unstable cart, stand, tripod, bracket, table, or floor where it can fall. A falling PDP can cause serious injury to a child or adult, and serious damage to the appliance. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer or sold with the PDP. Follow the manufacturer's instructions when mounting the unit, and use a mounting accessory recommended by the manufacturer. Move the PDP and cart with care. Quick stops, excessive force, and uneven surfaces can make the unit and cart unsteady and likely to overturn.

Provide ventilation for the PDP. The unit is designed with slots in the cabinet for ventilation to protect

it from overheating. 1_)onot block these openings with any object, and do not place the PDP on a bed, sofa, rug, or other similar surface. [Do not place it near a radiator or heat register. If you place the

PDP on a rack or bookcase, ensure that there is adequate ventilation and that you've followed the

manufacturer's instructions for mounting.

• Operate },our PDP only from the type of power source indicated on the marking labeh If you are not sure of the type of power supplied to },our home, consult },our appliance dealer or local power corn

pany.

Use only a grounded or polarized outlet. For your safety, this PDP is equipped with a polarized alternating current line plug having one blade wider than the other. This plug will fit into the power outlet only one way. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug still does not fit, contact your electrician to replace your outlet.

• Protect the power cord. Power supply cords should be routed so that they won't be walked on or pinched by objects placed on or against them. Pay particular attention to cords at plugs, convenience

receptacles, and the point where the}, exit from the unit.

_' Unplug the PDP from the wall outlet and disconnect the antenna or cable system during a lightning

storm or when left unattended and unused for long periods of time. This will prevent damage to the

unit due to lightning and power-line surges.

important Safety informations (UL1492)(continued

Avoid overhead power lines. An outside antenna system should not be placed in the vicinity of

overhead power lines or other electric light or power circuits or where it can fall into such power

lines or circuits. When installing an outside antenna system, be extremely careful to keep from

touching the power lines or circuits. Contact with such lines can be fatal.

Do not overload the wall outlet or extension cords. Overloading can result in fire or electric shock.

Do not insert anything through the openings in the unit, where they can touch dangerous voltage points or damage parts. Never spill liquid of any kind on the PDP.

Ground outdoor antennas. If an outside antenna or cable system is connected to the PDP, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Section 810 of the National Electrical Code, ANSI/NFPA No.70-1984, provides information about proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.

_' Do not attempt to service the PDP yourself. Refer all servicing to qualified service personneh Unplug

the unit from the wall outlet and refer servicing to qualified service personnel under the following

conditions:

- when the power-supply cord or plug is damaged

- if liquid has been spilled on the unit or if objects have fallen into the unit

- if the PDP has been exposed to rain or water

- if the PDP does not operate normally by following the operating instructions

- if the PDP has been dropped or the cabinet has been damaged

- when the PDP exhibits a distinct change in performance

'_ If you make adjustments yourself, adjust only those controls that are covered by the operating

instructions. Adjusting other controls may result in damage and will often require extensive work by a qualified technician to restore the PDP to normah

When replacement parts are required, be sure the service technician uses replacement parts specified

by the manufacturer or those that have the same characteristics as the original part. Unauthorized substitutions may result in additional damage to the unit.

Upon completion of any service or repairs to this PDP, ask the service technician to perform safety checks to determine that the PDP is in a safe operating condition.

The PDP can properly operate in a temperature range of 32-104°F(0-40°C) and 80% humidity. Do not use in a hot and humid place.

Before moving the PDP equipped with speakers, separate the speakers from the PDP. If you move the PDP with the speakers attached, it may result in damage or injury.

important Safety instructions (UL6500}

• Read these instructions.

• Keep these instructions.

• Heed all wan'tings.

• Follow all instructions.

• Do not use this apparatus near water.

• Clean only with dry cloth.

• Do not block any, ventilation openings, Install in accordance with the manufacturer's instructions.

• [Do not install neat" any, heat sources such as radiators, heat registers, or other apparatus (including amplifiers) that produce heat.

4!,

Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit

into your outlet, consult an elec trician for replacement of the obsolete outlet.

'0' Protect the power cord from being walked on or pinched particularly at

plugs, convenience receptacles, and the point where they, exit from the apparatus.

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii_i

t Only, use attachments/accessories specified by the manufacturer.

'0' Use only with cart, stand, tripod, bracket, or table specified by the

manufacturer, or sold with the apparatus. When a used, caution when

moving the cart/apparatus combination to avoid injury from tip-over.

• Unplug this apparatus during lightning storms or when unused for long periods of time.

Refer all servicing to qualified service personneh Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or

objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

iiiiiiiiiiiiiiiiiiiiiiiiiiiiii iiiiiiiiiiiiiiiiiiiiiiiiiiiiii iiiiiiiiiiiiiiiiiiiiiiiiiiiiii iiiiiiiiiiiiiiiiiiiiiiiiiiiiii

iiiiiiiiiiiiiiiiiiiiiiiiiiiiii iiiiiiiiiiiiiiiiiiiiiiiiiiiiii iiiiiiiiiiiiiiiiiiiiiiiiiiiiii iiiiiiiiiiiiiiiiiiiiiiiiiiiiii iiiiiiiiiiiiiiiiiiiiiiiiiiiiii

iiiiiiiiiiiiiiiiiiiiiiiiiiiiii iiiiiiiiiiiiiiiiiiiiiiiiiiiiii iiiiiiiiiiiiiiiiiiiiiiiiiiiiii iiiiiiiiiiiiiiiiiiiiiiiiiiiiii iiiiiiiiiiiiiiiiiiiiiiiiiiiiii iiiiiiiiiiiiiiiiiiiiiiiiiiiiii

iiiiiiiiiiiiiiiiiiiiiiiiiiiiii iiiiiiiiiiiiiiiiiiiiiiiiiiiiii iiiiiiiiiiiiiiiiiiiiiiiiiiiiii iiiiiiiiiiiiiiiiiiiiiiiiiiiiii iiiiiiiiiiiiiiiiiiiiiiiiiiiiii

iiiiiiiiiiiiiiiiiiiiiiiiiiiiii iiiiiiiiiiiiiiiiiiiiiiiiiiiiii iiiiiiiiiiiiiiiiiiiiiiiiiiiiii iiiiiiiiiiiiiiiiiiiiiiiiiiiiii iiiiiiiiiiiiiiiiiiiiiiiiiiiiii iiiiiiiiiiiiiiiiiiiiiiiiiiiiii

iiiiiiiiiiiiiiiiiiiiiiiiiiiiii iiiiiiiiiiiiiiiiiiiiiiiiiiiiii iiiiiiiiiiiiiiiiiiiiiiiiiiiiii iiiiiiiiiiiiiiiiiiiiiiiiiiiiii iiiiiiiiiiiiiiiiiiiiiiiiiiiiii

iiiiiiiiiiiiiiiiiiiiiiiiiiiiii iiiiiiiiiiiiiiiiiiiiiiiiiiiiii iiiiiiiiiiiiiiiiiiiiiiiiiiiiii iiiiiiiiiiiiiiiiiiiiiiiiiiiiii iiiiiiiiiiiiiiiiiiiiiiiiiiiiii iiiiiiiiiiiiiiiiiiiiiiiiiiiiii

iiiiiiiiiiiiiiiiiiiiiiiiiiiiii iiiiiiiiiiiiiiiiiiiiiiiiiiiiii iiiiiiiiiiiiiiiiiiiiiiiiiiiiii iiiiiiiiiiiiiiiiiiiiiiiiiiiiii iiiiiiiiiiiiiiiiiiiiiiiiiiiiii

iiiiiiiiiiiiiiiiiiiiiiiiiiiiii iiiiiiiiiiiiiiiiiiiiiiiiiiiiii iiiiiiiiiiiiiiiiiiiiiiiiiiiiii iiiiiiiiiiiiiiiiiiiiiiiiiiiiii

FCC information

User instructions

The Federal Communications Commission Radio

Frequency interference Statement includes the

following wan'ring:

NOTE: This equipment has been tested and found to

comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against

harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful

nterferencetoradiocommunications.However,there

is no guarantee that interference will not occur in a

particu,ar, sta,lat,on

If this equipment does cause harmful interference to

radio or PDP receptions, which can he determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or

more of the following measures:

• Reorient or relocate the receiving antenna,

• Increase the separation between the equipment

and receiver.

• Connect the equipment into an outlet on a circuit

different from that to which the receiver is connected,

• Consult the dealer or an experienced radio/PDP

technician for help.

Warnh_g

User must use shielded signal interface cables to maintain FCCcompliance for the product. Provided with this monitor is a detachable power supply cord with IEC320 style terminations, It may be suitable for connection to any LJI.Listed personal computer with

similar configuration. Before making the connection, make sure the voltage rating of the computer convenience outlet is the same as the monitor and that

the ampere rating of the computer convenience outlet is equal to or exceeds the monitor voltage rating,

For 120 Volt applications, use only LJI. Listed detachable power cord with NEMA configuration 5- 15P type (parallel blades) plug cap. For 240 Volt applications use only LJI.Listed Detachable power supply cord with NEMA configuration 6015P type /tandem blades) plug cap.

IC Compliance Notice

This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations of ICES-003.

Cet appareil Num6,rique de classe B respecte routes les exigences du R_glemont NMB-03 sur les 6,quipements

produisant des interf6rences au Canada,

User Informat_on Notice de Conformlt_ IC

Changes or modifications not expressly approved by the party responsible for compliance could void the

user's authority to operate the equipment, if necessary, consult your dealer or an experienced radio/PDP

technician for additional suggestions. You may find the booklet called. How to Identify and Resolve

Radio/PDP Interference Problems helpful, This booklet was prepared by the Federal Communications Commission, it is available from the U,S. Government

Printing Office, Washington, DC 20402, Stock

Number 004-000-00345-4.

The party responsible for product compliance: SAMSUNG ELECTRONICS CO., LTD

America QA Lab of Samsung 3351 Michelson Drive,

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiil;Suite#290,1rvine, CA92612 USA I CetappareiInum_rifluedeladasseBest

Cet appareil num_rique de classe B respecte routes les exigences du R&glement ICES-O03 sur les &quipements

produisant des interf&rences au Canada.

VCCl

[his is a Class Bproduct based on the standard of the Voluntary Control Council for Interference by

Information Technology Equipment (VCCI). If this is used near a radio or PDP receiver in a domestic

environment, it may cause radio interference. Install and use the equipment according to the instruction

manual.

] This Class B digital apparatus complies with ]

: Canadian ICES-OO3. ]

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii: ......................................................................

]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]ii, _ conformealanormeNMB-003dnCananda, i iiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]i This device complies with Part 15 of the FCC Rules. Operation _ssubjectto thefollow_ng two conditions: -' iiiiiiiiiiiiiiiiiiiiiiiiiiiiiii_I (1) This device may not cause harmful interference, and -'

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiilli (2) Thisdevicemustacceptanyinterferencereceived_inc_udi_gi_terferencethatmayca_se_desired_perad_. i

important Warranty information Regarding PDP Format Viewing

Wide screen format PDP Displays (16:9,the aspect ratio of the screen width to height) are primarily designed to view wide screen format full-motion video. The images displayed on them should primarily be in the wide screen 16:9 ratio format, or expanded to fill the screen if your model offers this feature and constantly moving. Displaying stationary graphics and images on screen, such as the dark side-bars on

non-expanded standard format PDP video and programming, should be limited to no more than 5% of

the total PDP viewing per week.

Additionally, viewing other stationary images and text such as stock market reports, video game displays, station Iogos, web sites or computer graphics and patterns, should be limited as described above for all

PDP displays. Displaying stationary images that exceed the above guidelines can cause uneven aging of

PDP Displays that leave subtle, but permanent burned-ln ghost images in the PDP plcture. To avoid this, vary the programming and images, and prlmarily display full screen moving images, not stationary

patterns or dark bars. On PDP models that offer picture sizing features, use these controls to view different formats as a full screen picture.

Be careful in the selection and duration of PDP formats used for viewing. Uneven PDP aging as a result

of format selection and use, as well as burned-in images, are not covered by your Samsung limited warranty.

iiiiiiiii!iiiiiiiiiiiiiiiiiiiiiii

User instructions

• Screen Image retention

Do not display a still image/such as on a video game or when hooking up a PC to this PDP) on the

plasma display panel for more than 2 h_,_,ursas it can cause screen image retention. This image retention is also known as "screen burn '. To avoid such image retention, reduce the degree of

brightness and contrast of this screen when displaying a still image.

Cell Defect

The plasma display panel consists of fine cells. Although the panels are produced with more than

99.9 percent active cells, there may be some cells that do not produce light or remain lit.

"_ Height

The PDP can normally operate only under 2000m in height. It might abnormally function at a place

over 2000m in height and do not install and operate there.

Warranty

- Warranty does not cover any damage caused by image retention.

- Burn-in is not covered by the warranty.

iiiiiiiiiiiiiiiiil iiiiiiiiiiiiiiiiii_iiii

iiiiiiiiiiiiiiiiiiiiiiiiil iiiiiiiiiiiiiiiiiiiiiiiiii_iiii

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii_iiii

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii_iiii

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiil

_'- EUROPEAN NOTICE

Products with the CE marking comply with the EMC Directive

(89/336/EEC), (92/31/EEC), (93/68/EEC) and the I.ow Voltage

Directive (73/23/EEC) issued by the Commission of the European Community. Compliance with these directives

implies conformity to the following European Norms:

[] EN55022:1998

Radio Frequency, interference

[] EN55024:1998

Electromagnetic Immunity

[] EN61000-3-2:2000

Power [ine Harmonics

[] EN61000-3-3:1995

Voltage Fluctuations

[] EN60065

Product Safety,

Wiring the Mains Power Supply Plug (UK Only)

IMPORTANT NOTICE The mains lead on this equipment is supplied with a moulded plug incorporating a fuse. The value of the fuse is indicated onthe

pin face of the plug and, if it requires replaoing_a fuse approved to BSI1362 ofthe same rating must be used. Never use the plug with the fuse cover omitted ifthe cover is detachable. If a replacement fuse cover is required, it must be of the same colour as the

pin face of the plug. Replacement covers are available from your dealer. Ifthe fitted plug is not suitable for the power points in your house or the cable is not tong enough to reach a power point, you should obtain a suitable safety approved extension lead

or consult your dealer for assistance. However, if there is no alternative to cut off the plug, remove the fuse and then safely dispose of the plug. Do NOT connect the plug tea mains socket as there is a risk of shock hazard from the bared flexible cord.

iiiiiiiiiiiiiiiiiiiiiiiiiiiiii

mMPORTANT

The wires in the mains lead are coloured inaccordance with the following code:

BLUE- NEUTRAL BROWN- LIVE

AS these co,ours may not correspond to the co,cured markings identifying the termina,s in your p,ug, proceed as fol,ows[

The wire cotoured BLUE must be connected to the terminal marked with the letter Nor coloured BLUE or BLACK. The wire coloured BROWN must be connected tothe terminal marked with the letter L or coloured BROWN or RED.

WARNING: DO NOT CONNECT EITHER WIRE TO THE EARTH TERMINAL, wHICH IS MARKED wITH THE LETTER E OR BY

............................................................................................................... _ iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

! i_i

i i_i

THE EARTH SYMBOLs, OR COLOURED GREEN OR GREEN AND YELLOw.

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii_ HHHHHHHHHHHHHHHH_

PPM42S3 & _ iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

PPM5OH3 i iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

= HHHHHHHHHHHHHHHH_

HHHHHHHHHHHHHHHH_ HHHHHHHHHHHHHHHH_

: iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

owner's Instructions

Remote Control/

AAA Batteries

Power Cord

Speaker Wires

(2EA)

Stand-Base iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

(2EA) iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

HHHHHHHHHHHHHHHH_

m iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

2 Install CD

i - MDC Software (RS232C) Ferrite Cores for

- Pivot software Speaker Wire

PC Cable

Sorews i iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

MDCCable (4EA) ; iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

(RS232C) _

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

I iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

..................................................................................................................iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

This feature bring you more detailed image with 3D noise reduction, detail enhancement, contrast iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

enhancement and white enhancemenL New image compensation Algorithm gives brighter, clearer, iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

muchdetai/edimage,o ou. le 'technolog wi/l i,ever signalsinto oure es, iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

Contents

O FOREWORD

[] Warning! Important Safety Instructions ......................................................... 2

[] Important Safety Informations (UL1492) ....................................................... 3

[] Important Safety Informations (UL6500) ....................................................... 5

[] FCC Information ............................................................................................ 6

[] Important Warranty Information Regarding PDP Format Viewing ................. 7

[] User Instructions ............................................................................................ 8

[] Wiring the Mains Power Supply Plug (UK Only) ............................................ 9

CONNECTING AND PREPARING YOUR DISPLAY

[] Your New Plasma Display Panel ................................................................... 12

[] Becoming Familiar with the Remote Control ................................................. 14

[] Inserting the Batteries in the Remote Control ................................................ 15

[] Assembling the Stand-Base .......................................................................... 15

[] Installing the Display on the Wall Attachment Panel ..................................... 16

[] Installing the Display Vertically ...................................................................... 18

[] Before Using the Video Wall and the Multiple Display Contol function ......... 18

[] Connecting Speakers .................................................................................... 19

[] Switching On and Off ..................................................................................... 21

[] Choosing Your Language .............................................................................. 21

• USING

[] [] [] [] [] [] [] [] [] []

YOUR DISPLAY

Selecting the Color System (Video or S-Video Mode) ................................... 22

Changing the Picture Mode ........................................................................... 22

Adjusting the Picture Settings ........................................................................ 23

Adjusting the Picture Settings (PC or DVI Mode) .......................................... 24

Selecting the Picture Size .............................................................................. 25

Activating/Deactivating the Digital Noise Reduction Feature ........................ 25

Freezing the Current Picture ......................................................................... 26

Changing the Sound Mode ............................................................................ 26

Adjusting the Sound Settings ........................................................................ 27

Extra Sound Settings ..................................................................................... 28

- Auto Volume

- Melody

- Pseudo Stereo / Virtual Surround

Adjusting the Screen Position and Scale ....................................................... 29

Adjusting the Image Preferences (PC Mode) ................................................ 30

Contents (continued)

_" USING YOUr DISPLAY (CONTINUED)

m Locking the Control buttons ........................................................................... 31

m Setting the MDC (Multiple Display control) ................................................... 31

[] Protecting the Screen Burning ....................................................................... 32

[] Setting the Multiple Screen ............................................................................ 33

[] Displaying the Pc Information ....................................................................... 34

[] Displaying the Setting Information ................................................................. 34

[] Setting and Displaying the Current Time ....................................................... 35

[] Switching On and Off Automatically .............................................................. 36

[] Turning On the Fan ....................................................................................... 37

[] Setting the Film Mode .................................................................................... 37

[] Viewing the Picture In Picture (PIP) .............................................................. 38

[] Listening to the Sound of the Sub Picture ..................................................... 40

• ADDITIONAL INFORMATION AND CONNECTIONS

[] Viewing Pictures From External Sources ...................................................... 40

[] Connecting to the Audio/Video Input ............................................................. 41

[] Connecting to the S-Video Input .................................................................... 42

[] Connecting to the DVD/DTV RECEIVER Input ............................................. 42

[] Connecting to the DVI Input .......................................................................... 43

[] Connecting to the RGB(PC) Input ................................................................. 43

[] Setting up Your PC Software (Windows only) ............................................... 44

[] Pin Configurations ......................................................................................... 45

[] Input Mode (PC/DVI) ..................................................................................... 46

[] Power Saver (PC1 mode only) ...................................................................... 47

• RECOMMENDATIONS FOR USE

[] Troubleshooting: Before Contacting Service Personnel ................................ 48

[] Care and Maintenance .................................................................................. 48

[] Technical Specifications ................................................................................ 49

Symbols A

Press Important Note

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

iii)

Your New Plasma Display Panel

The actual configuration on your PDP may be different, depending on your model.

PPM42S3/PPM50H3

Speaker Speaker

PPM63H3

111111111111111111111111171:O

SOURCE

- External input selection.

- Store your settings in the menu.

- When the Main menu is displayed on screen,

>[heM</in Fflenu is not operated with source key.

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiill MENU

iiiiiiiiiiiiiiiiiiiiiiiiiiiiTiMenudisphy_,ndeX_t•

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii:- VOL+

7777777[[[_ ! -W,lumeadiustment.

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! ; - Ad ust an o ?tlon value resF)ectlvelv.

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii m

1 (VOIL + : Enter to the selected menu•

I SEjL A

i Control the cursor in the menu.

i I ! 0

l Press to turn the PDP on and off.

O .................................................

i Power Indicator

- Power Off; Red [

! - Powel" On; Off _1 [ - Timer On; Green l

.................................................

: remote Control signal receiver !

i Aim the remote control towards this spot on the I l PDP. ;

Your New Plasma Display Panel

_,_ The actual configuration on your PDP may be different,

depending on your model.

For further details about connection, refer to pages 41 ~43.

RS232C

- IN : Used for the MDC function when connecting PC or RS232C output of another PDP.

- OUT : Used for the MDC fundion when

connecting with RS232C input of another

PDP.

b) DVI IN

Connect to the video output ja(k for device with DVI output.

c) AUDIO

Connect to the audio OUtl)ut jack on your PC or any device with DVI output. (It is audio input for b, d, and e.)

d) RGBI(Pcl) IN

Connect to the video output jack on your PC.

e) COMPONENT2!RGB2(PC2) IN

Connect for input of an Analog RGB or Y/Pb/Pr video signal from in PC, DVD, or HD devices.

_;_ "PC Mode" from this page onward means

PC1/PC2 mode using RGBI(PCI) and RGB2(PC2).

VIDEO IN Video and audio inputs for external devices, such as

VCR, DVD, video ganle device or video disc players

(or for external devices with an S-Video output;

S-VIDEO).

COMPONENT1 IN Video (¥/Pb/Pr) and audio (UIR) inputs for cornponel_t.

VIDEO OUT (VIDEO / L-AUDIO-R)

Used to output screen of Video or S-Video in PDP

when connecting video and/or audio input of external devices.

EXT SPEAKER (8£-2)

Connect external speakers.

POWER IN

Conne{ t the supplied power cord.

iiiiiiiii!iiiiiiiiiiiiiiiiiiiiiiii

Becoming Familiar with the Remote Control 1

* _et up the PD, ,sing the of*_-,creen me.u ,_,tem

ON OFF

PDPON

PDPOFF

............................BOUNDMODOBELECT,ONI I _oii_,_o_,,D_p_

PICTUREMODEBELECTION O0RRENTTIMEDIBPLAY

[ :: : ]

NUMERIC BUTTONS _1 _ _ _ I

PICTURE STILL N _ ZOOM/PANNING MENU DISPLAY

J I V0L CH I I (ONLY PC MODE)

URCEI

TEMPORARYBOUNDB_ITCN-O_F EXTERNAL,NPOTBELECT,ON

_P.....o0o1.....,+botto°

tO turn the sound back On.

VOLUME DECREASE

SETTING THE TIMER

DISPLAY AND CLOSE THE MENU/ EXIT FROM ANY DISPLAY

I I .... .....

RETURNTOTHEPREV,OOBMENU

NEXT CHANNEL

{NOT AVAILABLE FOR THIS MONITOR)

I I PREVIOUS CHANNEL

,NFORMAT,ONDIBPLAY

MOVE TO TNE REQUIRED MENU

ADJUST AN OPTION VALUE

OPTION/

RESPECTIVELY

SCREENOPFECTBELECTIONM0CII CNANGECONF,RMAT,ON

AUTO ADJUSTMENT(BURNINGPROTECTION)INPC MODE [ I ;.EFFECT P.SIZE MULTIPLE DISPLAY CONTROL

P,CTUREB,ZEBELECT,ON

SWAP S;SEL PiPFUNCTIONS;

I _L_ _¢_. /-_ _ " PiP ON/OFF

II............ J - SIZE SELECTION (SIZE)

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiii - INPUT SOURCE SELECTION

rh_p_o_m_,,_eo__h__.,o_ _o,._o;maybea_,,_te,__ b_i_h_;;_h_.

- LOCATION SELECTION (LOCATE)

(souRcE)

- INTERCHANGE THE MAIN AND THE SUB PICTURE (SWAP)

" SOUND SELECTION (S,SEL)

inserting the Batteries in the Remote ControJ

You must insert or replace the batteries in the remote control when

you:

0 Purchase the PDP

0 Find that the remote control is no longer operating

correctly

1 Remove the cover on the rear of the remote control by pressing

the symbol downwards and then pulling firmly to remove it.

2 insert two R03, UM4, "AAA" 1.5V or equivalent batteries taking

care to respect the polarities:

• = on the battery against = on the remote control _i, + on the battery against + on the remote control

3 Replace the cover by aligning it with the base of the remote

control and pressing it back into place.

Assembling the Stand-Base

Fit the Stand-Base into the guide hole on the bottom of the monitor and tighten the left and right sides using

four screws for each side.

Two or more people should carry the PDP. Never lay the PDP on the floor because of possible damage to the screen. Always store the PDP upright.

For the PPM63H3 model, please see the instruction for the SMM6330 stand.

+ 35 hidden pages