Samsung PN63B590T5F, PN50B550T2F, PN58B550T2F, PN58B560T5F, PN50B560T5F User Manual

...

Contact SAMSUNG WORLD-WIDE If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care center.

Comment contacter Samsung dans le monde Si vous avez des suggestions ou des questions concernant les produits Samsung, veuillez contacter le Service Consommateurs Samsung.

Country

U.S.A 1-800-SAMSUNG(726-7864) www.samsung.com/us

CANADA 1-800-SAMSUNG(726-7864) www.samsung.com/ca

Customer Care Center 

Web Site Address

Samsung Electronics America, Inc. 105 Challenger Road Ridgefield Park, NJ 07660-0511

Samsung Electronics Canada Inc., Customer Service 55 Standish Court Mississauga, Ontario L5R 4B2 Canada

Samsung Electronique Canada Inc., Service à la Clientèle 55 Standish Court Mississauga, Ontario L5R 4B2 Canada

Plasma TV

user manual

BN68-02221A-00

imagine the possibilities

Thank you for purchasing this Samsung product. To receive more complete service, please

www.samsung.com/register

Model Serial No.

Important Warranty Information Regarding Television Format Viewing

Wide screen format PDP Displays (16:9, the aspect ratio of the screen width to height) are primarily designed to view wide screen format full-motion video. The images displayed on them should primarily be in the wide screen 16:9 ratio format, or expanded to fill the screen if your model offers this feature and the images are constantly moving. Displaying stationary graphics and images on screen, such as the dark side-bars on nonexpanded standard format television video and programming, should be limited to no more than 5% of the total television viewing per week.

Additionally, viewing other stationary images and text such as stock market reports, video game displays, station logos, web sites or computer graphics and patterns, should be limited as described above for all televisions. Displaying stationary

images that exceed the above guidelines can cause uneven aging of PDP Displays that leave subtle, but permanent burned-in ghost images in the PDP picture. To avoid this, vary the programming and images, and primarily display full screen moving images, not stationary patterns or dark bars.

On PDP models that offer picture sizing features, use these controls to view different formats as a full screen picture. Be careful in the selection and duration of television formats used for viewing. Uneven PDP aging as a result of format selection and use, as well as burned-in images, are not covered by your Samsung limited warranty.

U.S.A Only

The product unit accompanying this user manual is licensed under certain intellectual property rights of certain third parties. In particular, this product is licensed under the following US patents: 5,991,715, 5,740,317, 4,972,484, 5,214,678, 5,323,396, 5,539,829, 5,606,618, 5,530,655, 5,777,992, 6,289,308, 5,610,985, 5,481,643, 5,544,247, 5,960,037, 6,023,490, 5,878,080, and under US Published Patent Application No. 2001-44713-A1.

This license is limited to private non-commercial use by end-user consumers for licensed contents. No rights are granted for commercial use. The license does not cover any product unit other than this product unit and the license does not extend to any unlicensed product unit or process conforming to ISO/IEC 11172-3 or ISO/IEC 13818-3 used or sold in combination with this product unit. The license only covers the use of this product unit to encode and/or decode audio files conforming to the ISO/IEC 11172-3 or ISO/IEC 13818-3. No rights are granted under this license for product features or functions that do not conform to the ISO/IEC 11172-3 or ISO/IEC 13818-3.

Other countries

The product unit accompanying this user manual is licensed under certain intellectual property rights of certain third parties. This license is limited to private non-commercial use by end-user consumers for licensed contents. No rights are granted for commercial use. The license does not cover any product unit other than this product unit and the license does not extend to any unlicensed product unit or process conforming to ISO/IEC 11172-3 or ISO/IEC 13818-3 used or sold in combination with this product unit. The license only covers the use of this product unit to encode and/or decode audio files conforming to the ISO/IEC 11172-3 or ISO/IEC 13818-3. No rights are granted under this license for product features or functions that do not conform to the ISO/IEC 11172-3 or ISO/IEC 13818-3.

English - 2

User Instructions

English - 3

Screen Image retention

Do not display a still image (such as on a video game) on the plasma display panel for more than several minutes as it can cause screen image retention. This image retention is also known as “screen burn”. To avoid such image retention, refer to page 25 of this manual to reduce the degree of brightness and contrast of the screen when displaying a still image.

Altitude

The PDP can only operate normally at heights under 6500ft.

Heat on the top of the Plasma TV

The top side of the product may be hot after long periods of use as heat dissipates from the panel through the vent hole in the upper part of the product. This is normal and does not indicate any defect or operation failure of the product. However, children should be prevented from touching the upper part of the product.

The product is making a ‘cracking’ noise.

A ‘cracking’ noise may occur when the product contracts or expands due to a change in the surrounding environment such as temperature or humidity. This is normal and not a defect of the unit.

Cell Defects

The PDP uses a panel consisting of 2,360,000(HD-level) to 6,221,000(FHD-level) pixels which require sophisticated technology to produce. However, there may be a few bright or dark pixels on the screen. These pixels will have no impact on the performance of the product.

Avoid operating the TV at temperatures below 41°F (5°C)

A still image displayed too long may cause permanent damage to the PDP Panel.

Watching the Plasma TV in 4:3 format for a long period of time may leave traces of borders displayed on the left, right and center of the screen caused by the difference of light emission on the screen. Playing a DVD or a game console may cause similar effects to the screen. Damages caused by the above effect are not covered by the Warranty.

After-images on the Screen.

Displaying still images from Video games and PC for longer than a certain period of time may produce partial after-images. To prevent this effect, reduce the ‘brightness’ and ‘contrast’ when displaying still images for a long time.

Warranty

Warranty does not cover any damage caused by image retention. Burn-in is not covered by the warranty.

Contents

Connecting and Preparing Your TV

English

List of Features ..........................................................................5

■

Checking Parts ..........................................................................5

■

Assembling the Cables ..............................................................5

■

Viewing the Control Panel .........................................................6

■

Viewing the Connection Panel...................................................8

■

Remote Control .........................................................................9

■

Connections

Connecting VHF and UHF Antennas .......................................10

■

Connecting Cable TV ..............................................................10

■

Connecting a DVD / Blu-Ray Player or Cable Box /

■

Satellite receiver (Set-Top Box) via HDMI ............................... 12

Connecting a DVD /Blu-Ray Player or Cable Box /

■

Satellite receiver (Set-Top Box) via DVI .................................. 12

Connecting a DVD / Blu-Ray Player or Cable Box /

■

Satellite receiver (Set-Top Box) via Component cables .......... 13

Connecting a Camcorder ........................................................13

■

Connecting a VCR ...................................................................14

■

Connecting a Digital Audio System .........................................15

■

Connecting an Amplier / DVD Home Theater ........................15

■

Connecting a PC .....................................................................16

■

Operation

Turning the TV On and Off ......................................................17

■

Changing Channels ................................................................. 17

■

Adjusting the Volume ...............................................................17

■

Using the TOOLS Button .........................................................18

■

Using the Remote Control Backlight Buttons ..........................18

■

Viewing the Display .................................................................18

■

Viewing the Menus ..................................................................19

■

Plug & Play Feature ................................................................20

■

Channel Control

Storing Channels .................................................................... 21

■

Managing Channels ................................................................21

■

PC Display

Using Your TV as a Computer (PC) Display ............................27

■

Display Modes ......................................................................... 27

■

Setting up the TV with your PC ...............................................28

■

Sound Control

Changing the Sound Settings ..................................................29

■

Function Description

Conguring the Setup Menu ....................................................30

■

Setting the Time ......................................................................34

■

Source List / Edit Name ...........................................................35

■

Support .................................................................................... 35

■

Media Play

Using the Media Play Function ................................................37

■

Using the PHOTO (JPEG) List ................................................38

■

Using the MP3 List ..................................................................41

■

Using the Setup Menu ............................................................. 42

■

Anynet

Connecting Anynet+ Devices ..................................................43

■

Troubleshooting for Anynet

■

+ ...................................................46

Appendix

Troubleshooting .......................................................................47

■

Preparation before installing the Wall-Mount ...........................48

■

How to attach the Stand-Base .................................................48

■

Securing the TV to the Wall .....................................................49

■

Wall Mount Kit Specications (VESA) .....................................50

■

Specications ..........................................................................51

■

Dimensions (PN50B550T2F/PN50B560T5F) ..........................52

■

Dimensions (PN58B550T2F/PN58B560T5F) ..........................53

■

Dimensions (PN63B550T2F/PN63B590T5F) ..........................54

■

Picture Control

Changing the Picture Settings ................................................. 23

■

Symbol

Press Note One-Touch Button TOOLS

N O T

English - 4

Connecting and Preparing Your TV

English - 5

List of Features

Adjustable picture settings that can be stored in the TV’s memory.

• Automatic timer to turn the TV on and off.

• A special sleep timer.

• V-Chip function.

• Excellent Digital Interface & Networking :

• With a built-in HD digital tuner, non-subscription HD broadcasts can be viewed with no Cable Box/Satellite receiver (Set-Top Box) needed.

You can listen to music les and view pictures on USB Mass Storage Class (MSC) devices.

• HDMI/DVI connection of your PC to this TV.

• SRS TruSurround HD provides a virtual surround system.

•

Checking Parts

Please make sure the following items are included with your TV. If any items are missing, contact your dealer.

The items' color and shape may vary depending on the model.

Remote Control

(BN59-00852A) /

AAA Batteries

(4301-000103)

Ferrite Core for Power

Cord

(3301-001305)

Ferrite Core

Power Cord

(3903-000144)

Ferrite Core for Side-

(3301-001201)

PN58B550T2F/

PN58B560T5F only

Owner’s Instructions /

Quick Setup Guide

Warranty Card /

Safety Guide Manual

(Not available in all

Cover-Bottom (Refer to page 48) PN50B550T2F/

PN50B560T5F only

Cleaning Cloth

(BN63-01798B)

locations)

Cover-Bottom /

PN58B550T2F/PN58B560T5F/

PN63B550T2F/PN63B590T5F

Screw (2ea)

(Refer to page 48)

only

The ferrite cores are used to shield the cables from interference. When connecting a cable, open the ferrite core and clip it around the cable near the plug.

Assembling the Cables

Enclose the cables in the Holder-Wire Cable so that the cables are not visible through the transparent stand.

Holder-Wire

Cable

Holder-Ring (4ea) (Refer to page 48)

Power Cord

TV-Holder / Screw

(BN96-10788A)

(Refer to page 49)

Screw (4ea)

PN50B550T2F/

PN50B560T5F only

Audio Cable / Video Cable

(PN58B550T2F/

PN58B560T5F only)

Viewing the Control Panel

The buttons on the lower-right panel control your TV’s basic features, including the on-screen menu. To use the more advanced features, you must use the remote control.

The product color and shape may vary depending on the model.

If you touch the front panel button, the each button will be operated.

PN50B550T2F/PN58B550T2F/PN63B550T2F

SOURCEE

Toggles between all the available input sources (TV, AV1, AV2, Component1, Conponent2, PC, HDMI1, HDMI2/DVI, HDMI3, HDMI4). In the on-screen menu, use this button as you use the ENTERE button on the remote control.

Press to see an on-screen menu of your TV’s features.

+ VOL –

Press to increase or decrease the volume. In the on-screen menu, use the + VOL – buttons as you would use the

◄ and ► buttons on the remote control.

< CH >

Press to change channels. In the on-screen menu, use the < CH > buttons as you would use the ▲ and ▼ buttons on the remote control.

POWER INDICATOR

Blinks and turns off when the power is on and lights up in stand-by mode.

P (POWER)

Press to turn the TV on and off.

REMOTE CONTROL SENSOR

Aim the remote control towards this spot on the TV.

SPEAKERS

English - 6

English - 7

PN50B560T5F/PN58B560T5F/PN63B590T5F

SOURCEE

Press to see an on-screen menu of your TV’s features.

+ VOL –

Press to increase or decrease the volume. In the on-screen menu, use the + VOL – buttons as you would use the

◄ and ► buttons on the remote control.

< CH >

Press to change channels. In the on-screen menu, use the < CH > buttons as you would use the ▲ and ▼ buttons on the remote control.

POWER INDICATOR

Blinks and turns off when the power is on and lights up in stand-by mode.

REMOTE CONTROL SENSOR

Aim the remote control towards this spot on the TV.

SPEAKERS

P POWER

Touch the silver sensor below the (P) mark to turn the TV on and off.

Viewing the Connection Panel

Use the connection panel jacks to connect A/V components that will be connected continuously, such as Blu-Ray/DVD players or a VCR.

The product color and shape may vary depending on the model.

TV Rear Panel TV Side Panel

POWER IN

Connects the supplied power cord.

AUDIO OUT

Connect to a Digital Audio component.

PC IN [PC] / [AUDIO]

Connects to the video and audio output jacks on your PC.

DVI AUDIO IN (AUDIO-R/L)

Connect to the DVI audio output jack of an external device.

HDMI IN 1, 2(DVI), 3, 4

Connect to the HDMI jack of a device with an HDMI output. (HDMI 2 supports HDMI-DVI IN and connection from a PC.)

HDMI 2 can also be used as a DVI connection with

separate analog audio inputs. An optional HDMI/DVI cable will be necessary to make this connection.

When using an optional HDMI/DVI adapter, the DVI

analog audio inputs on your TV allow you to receive left and right audio from your DVI device.

ANT IN

Uses a 75Ω Coaxial connector for an Air/Cable Network.

DIGITAL AUDIO OUT (OPTICAL)

Connects to a Digital Audio component.

COMPONENT IN 1, 2 / AV IN 1

Connects Component video / audio. The COMPONENT IN 1 jack is also used as the AV IN 1 jack.

Connect the video cable to the COMPONENT IN 1

[Y/VIDEO] jack and the audio cable to the COMPONENT IN 1 [R-AUDIO-L] jacks.

EX-LINK

Used for service only.

USB

Connect a USB mass storage device to view photo les and play audio les.

AV IN 2

Video and audio inputs for external devices.

English - 8

Remote Control

English - 9

You can use the remote control up to a distance of about 23 feet from the TV.

The product color and shape may vary depending on the model.

The performance of the remote control may be affected by bright light.

POWER

Turns the TV on and off.

Selects the TV mode directly.

NUMERIC BUTTONS

Press to change the channel.

Press to select additional channels (digital and analog) being broadcast by the same station. For example, to select channel “54-3”, press “54”, then press “ ” and “3”.

MMUTE

Press to temporarily cut off the sound.

VOL

Press to increase or decrease the volume.

SOURCE

Press to display and select the available video sources.

CH LIST

Used to display Channel Lists on the screen.

TOOLS

Use to quickly select frequently used functions.

UP▲/DOWN▼/LEFT◄/

RIGHT►/ENTER Use to select on-screen menu items and change menu values.

INFO

Press to display information on the TV screen.

COLOR BUTTONS

Use these buttons in the Channel list and Media Play function.

MEDIA.P (Media play)

This function enables you to view and play

photo and music les from an external

device. (Refer to pages 38 (Photo) and 41 (Music))

P.MODE

Press to select the picture mode.

Use these buttons in the DMA, Media Play

and Anynet+ modes. ( : This remote can be used to control recording on Samsung recorders with the Anynet+ feature)

ON/OFF

Press to backlight the buttons on the remote. This function is convenient for using at night or when the room is dark. (Using the remote control with the light button set to On will reduce the battery usage time.)

PRE-CH

Tunes to the previous channel.

Press to change channels.

(

Displays the on-screen menu.

FAV.CH

)

Press to switch to your favorite channels.

RETURN

Returns to the previous menu.

EXIT

Press to exit the menu.

P.SIZE

Picture size selection.

SRS

Selects SRS TruSurround HD mode.

Controls the caption decoder.

MTS

Press to choose stereo, mono or Separate Audio Program (SAP broadcast).

Installing Batteries in the Remote Control

❑

1. Lift the cover at the back of the remote control upward as shown in the gure.

2. Install two AAA size batteries.

Make sure to match the “+” and “–” ends of the batteries with the diagram inside the compartment.

3. Close the cover as shown in the gure.

Remove the batteries and store them in a cool, dry place if you won’t be using the remote control for a

long time. (Assuming typical TV usage, the batteries should last for about one year.) Using the remote control with the ON/OFF( ) light button set to On will reduce the battery usage

time.

If the remote control doesn’t work, check the following

1. Is the TV power on?

2. Are the plus and minus ends of the batteries reversed?

3. Are the batteries drained?

4. Is there a power outage or is the power cord unplugged?

5. Is there a special uorescent light or neon sign nearby?

Connections

Connecting VHF and UHF Antennas

If your antenna has a set of leads that look like this, see “Antennaswith300ΩFlatTwin Leads” below.

If your antenna has one lead that looks like this, see “Antennaswith75ΩRoundLeads”. If you have two antennas, see “Separate VHF and UHF Antennas”.

Antennaswith300ΩFlatTwinLeads

❑

Ifyouareusinganoff-airantenna(suchasaroofantennaorrabbitears)thathas300Ω

twin flat leads, follow the directions below.

1. Place the wires from the twin leads under the screws on a 300-75 Ω adapter (not supplied).

Use a screwdriver to tighten the screws.

2. Plug the adaptor into the ANT IN terminal on the back of the TV.

Antennaswith75ΩRoundLeads

❑

Plug the antenna lead into the ANT IN terminal on the back of the TV.

Separate VHF and UHF Antennas

❑

If you have two separate antennas for your TV (one VHF and one UHF), you must combine the two antenna signals before connecting the antennas to the TV. This procedure requires an optional combiner-adaptor (available at most electronics shops).

1. Connect both antenna leads to the combiner.

2. Plug the combiner into the ANT IN terminal on the bottom of the back panel.

ANT IN

UHF

VHF

ANT IN

UHF

VHF

Connecting Cable TV

To connect to a cable TV system, follow the instructions below.

Cable without a Cable Box

❑

Plug the incoming cable into the ANT IN terminal on the back of the TV.

Because this TV is cable-ready, you do not need a cable box to view unscrambled cable channels.

Connecting to a Cable Box that Descrambles All Channels

❑

1. Find the cable that is connected to the ANT OUT terminal on your cable box.

This terminal might be labeled “ANT OUT”, “VHF OUT” or simply, “OUT”.

2. Connect the other end of this cable to the ANT IN terminal on the back of the TV.

English - 10

ANT IN

ANT OUT

ANT IN

Continued...

Connecting to a Cable Box that Descrambles Some Channels

English - 11

❑

If your cable box descrambles only some channels (such as premium channels), follow the instructions below. You will need a two-way splitter, an RF (A/B) switch, and four lengths of Antenna cable. (These items are available at most electronics stores.)

1. Find and disconnect the cable that is

connected to the ANT IN terminal on your cable box.

This terminal might be labeled “ANT IN”,

ANT IN

“VHF IN” or simply, “IN”.

2. Connect this cable to a two-way splitter.

Incoming

cable

Splitter

3. Connect an Antenna cable between the

OUTPUT terminal on the splitter and the IN terminal on the cable box.

Incoming

cable

Splitter

IN CABLE OUT

Cable Box

4. Connect an Antenna cable between the ANT

OUT terminal on the cable box and the B–IN terminal on the RF(A/B) switch.

Incoming

cable

Splitter

IN CABLE OUT

Cable Box

A B

RF (A/B)

Switch

5. Connect another cable between the other

OUT terminal on the splitter and the A–IN terminal on the RF (A/B) switch.

Incoming

cable

IN CABLE OUT

Splitter

Cable Box

A B

RF (A/B)

Switch

6. Connect the last Antenna cable between the

OUT terminal on the RF (A/B) switch and the ANT IN terminal on the rear of the TV.

Incoming

cable

Splitter

IN CABLE OUT

A B

RF (A/B)

Switch

TV Rear

ANT IN

After you have made this connection, set the A/B switch to the “A” position for normal viewing. Set the A/B switch to the “B” position to view scrambled channels. (When you set the A/B switch to “B”, you will need to tune your TV to the cable box’s output channel, which is usually channel 3 or 4.)

Connecting a DVD / Blu-Ray Player or Cable Box / Satellite receiver (Set-Top Box) via HDMI

This connection can only be made if there is an HDMI Output jack on the external device. This connection will provide the highest quality picture.

1. Connect an HDMI Cable between the HDMI IN (1, 2(DVI), 3, or 4) jack on the TV and the HDMI jack on the DVD / Blu-Ray Player or

Cable Box / Satellite receiver (Set-Top Box).

DVD/Blu-Ray Player or Cable

Box / Satellite receiver

HDMI Cable (Not supplied)1

What is HDMI?

HDMI, or high-denition multimedia interface, is an interface that enables the transmission of digital audio and video signals

•

TV Rear Panel TV Side Panel

using a single cable. The difference between HDMI and DVI is that the HDMI device is smaller in size and has the HDCP (High Bandwidth Digital

•

Copy Protection) coding feature installed.

Each DVD Player or Cable Box / Satellite receiver (Set-Top Box) has a different back panel conguration.

The TV may not output sound and pictures may be displayed with abnormal color when DVD / Blu-Ray Player or Cable Box /

Satellite receiver supporting HDMI versions older than 1.3 are connected. When connecting an older HDMI cable and there is no sound, connect the HDMI cable to the HDMI IN 2(DVI) jack and the audio cables to the DVI AUDIO IN [R-AUDIO-L] jacks on the back of the TV. If this happens, contact the company that provided the DVD / Blu-Ray Player or Cable Box / Satellite receiver to Player or Cable Box / Satellite receiver to receiver to

conrm the HDMI version, then request an upgrade. HDMI cables that are not 1.3 may cause annoying icker or no screen display.

Connecting a DVD /Blu-Ray Player or Cable Box / Satellite receiver (Set-Top Box) via DVI

This connection can only be made if there is a DVI Output jack on the external device.

1. Connect a HDMI/DVI Cable or DVI-HDMI Adapter between the HDMI IN 2(DVI) jack on the TV and the DVI jack on the DVD / Blu-

Ray Player or Cable Box/Satellite receiver (Set-Top Box).

2. Connect Audio Cables between the DVI AUDIO IN [R-AUDIO-L] jack on the TV and the DVD/Blu-Ray Player or Cable Box / Satellite

receiver.

DVD/Blu-Ray Player or Cable Box /

Satellite receiver

Audio Cable (Not supplied)

HDMI/DVI Cable (Not supplied)1

Each DVD / Blu-Ray Player or Cable Box / Satellite receiver (Set-Top Box) has a different back panel conguration.

When connecting a DVD Player or Cable Box / Satellite receiver (Set-Top Box), match the color of the connection terminal to the

TV Rear Panel

cable.

When using an HDMI / DVI cable connection, you must use the HDMI IN 2(DVI) jack.

English - 12

Connecting a DVD / Blu-Ray Player or Cable Box / Satellite receiver

English - 13

(Set-Top Box) via Component cables

The rear panel jacks on your TV make it easy to connect a DVD/Blu-Ray Player or Cable Box / Satellite receiver (Set-Top Box) to your TV.

1. Connect Component Cable between theConnect Component Cable between the COMPONENT IN (1 or 2) [Y, PB, PR] jacks on the TV and the COMPONENT [Y, PB, PR]

jacks on the DVD / Blu-Ray Player or Cable Box / Satellite receiver(Set-Top Box).

2. Connect Audio Cables between the COMPONENT IN (1 or 2) [R-AUDIO-L] jacks on the TV and the AUDIO OUT jacks on the DVD /

Blu-Ray Player or Cable Box / Satellite receiver (Set-Top Box).

TV Rear Panel

DVD / Blu-Ray Player or Cable Box

/ Satellite receiver

Audio Cable (Not supplied)

Component Cable (Not supplied)1

Component video separates the video into Y (Luminance (brightness)), PB (Blue) and PR (Red) for enhanced video quality. Be sure

to match the component video and audio connections. For example, if connecting the video cable to COMPONENT IN 1, connectent video and audio connections. For example, if connecting the video cable to COMPONENT IN 1, connect the audio cable to COMPONENT IN 1 also.

Each DVD / Blu-Ray Player or Cable Box / Satellite receiver (Set-Top Box) has a different back panel conguration.

When connecting a DVD / Blu-Ray Player or Cable Box / Satellite receiver (Set-Top Box), match the color of the connection terminal (Set-Top Box), match the color of the connection terminal

to the cable.

Connecting a Camcorder

The side and rear panel jacks on your TV make it easy to connect a camcorder to your TV.

Using an Video / Audio Cable

❑

1. Connect a Video Cable between the AV IN 2 [VIDEO] jack on the TV and the VIDEO OUT jack on the camcorder.

2. Connect Audio Cables between the AV IN 2 [L-AUDIO-R] jacks on the TV and the AUDIO OUT jacks on the Camcorder.

Each Camcorder has a different back panel conguration.

TV Side Panel

Video Cable (Not supplied)

Camcorder

When connecting a Camcorder, match the color of the connection terminal to the cable.

Audio Cable (Not supplied)2

Using an HDMI Cable

❑

1. Connect an HDMI Cable between the HDMI IN (1, 2(DVI), 3, or 4) jack on the TV and the HDMI jack on the camcorder.

Camcorder

HDMI Cable (Not supplied)1

Each Camcorder has a different back panel conguration.

TV Rear Panel

TV Side Panel

Connecting a VCR

Video Connection

❑

These instructions assume that you have already connected your TV to an antenna or a cable TV system (according to the instructions on pages 10~11). Skip step 1 if you have not yet connected to an antenna or a cable system.

1. Unplug the cable or antenna from the back of the TV.

2. Connect the cable or antenna to the ANT IN terminal on the back of the VCR.

3. Connect an Antenna Cable between the ANT OUT terminal on the VCR and the ANT IN terminal on the TV.

4. Connect a Video Cable between the AV IN 1 [Y/VIDEO] or AV IN 2 [VIDEO] jack on the TV and the VIDEO OUT jack on the

VCR.

5. Connect Audio Cables between the AV IN 1 (or AV IN 2) [R-AUDIO-L] jacks on the TV and the AUDIO OUT jacks on the VCR

TV Rear Panel

VCR Rear Panel

Audio Cable(Not supplied)

If you have a “mono” (non-stereo) VCR, use a Y-connector (not supplied) to connect to the right and left audio input jacks of the

Video Cable(Not supplied)

Antenna cable(Not supplied)3

TV Side Panel

TV. Alternatively, connect the cable to the “R” jack. If your VCR is stereo, you must connect two cables.

Each VCR has a different back panel conguration.

When connecting a VCR, match the color of the connection terminal to the cable.

When connecting to AV IN 1, the color of the AV IN 1 [Y/VIDEO] jack (Green) does not match the color of the video cable (Yellow).

English - 14

Connecting a Digital Audio System

English - 15

The rear panel jacks on your TV make it easy to connect a Digital Audio System(Home theater/Receiver) to your TV.

1. Connect an Optical Cable between the DIGITAL AUDIO OUT (OPTICAL) jacks on the TV and the Digital Audio Input (OPTICAL)

jacks on the Digital Audio System.

When a Digital Audio System is connected to the DIGITAL AUDIO OUT (OPTICAL) jack : Decrease the volume of the TV, and adjust the volume level with the system’s volume control.

TV Rear Panel

Digital Audio System

Optical Cable (Not supplied)

5.1CH audio is possible when the TV is connected to an external device supporting 5.1CH.

Each Digital Audio System has a different back panel conguration.

When the receiver (home theater) is set to On, you can hear sound output from the TV’s Optical jack. When the TV is displaying a

DTV(air) signal, the TV will send out 5.1 channel sound to the Home theater receiver. When the source is a digital component such as a DVD and is connected to the TV via HDMI, only 2 channel sound will be heard from the Home Theater receiver. If you want to hear 5.1 channel audio, connect the DIGITAL AUDIO OUT (OPTICAL) jack on the DVD / Blu-Ray player or Cable/

Satellite Box directly to an Amplier or Home Theater, not the TV.

Connecting an Amplifier / DVD Home Theater

1. Connect Audio Cables between the AUDIO OUT [R-AUDIO-L] jacks on the TV and AUDIO IN [L-AUDIO-R] jacks on the Amplier/

DVD Home Theater.

When an audio amplier is connected to the AUDIO OUT [R-AUDIO-L] jacks terminals : Decrease the volume of the TV, and adjust the volume level with the Amplier’s volume control.

TV Rear Panel

Amplifier / DVD Home Theater

Audio Cable (Not supplied)

Each Amplier / DVD Home Theater has a different back panel conguration.

When connecting an Amplier / DVD Home Theater, match the color of the connection terminal to the cable.

Connecting a PC

Using a D-Sub Cable

❑

1. Connect a D-Sub Cable between PC IN [PC] jack on the TV and the PC output jack on your computer.

2. Connect a PC Audio Cable between the PC IN [AUDIO] jack on the TV and the Audio Out jack of the sound card on your

computer.

TV Rear Panel

PC Audio Cable (Not supplied)

D-Sub Cable (Not supplied)1

Using an HDMI/DVI Cable

❑

1. Connect an HDMI/DVI cable between the HDMI IN 2(DVI) jack on the TV and the PC output jack on your computer.

2. Connect a 3.5 mm Stereo plug to 2RC

the sound card on your computer.

A cable between the DVI AUDIO IN [R-AUDIO-L] jack on the TV and the Audio Out jack of

TV Rear Panel

3.5 mm Stereo plug to 2 RCA Cable (Not supplied)

HDMI/DVI Cable (Not supplied)1

Each PC has a different back panel conguration.

When connecting a PC, match the color of the connection terminal to the cable.

When using an HDMI/DVI cable connection, you must use the HDMI IN 2(DVI) terminal.

English - 16

Operation

English - 17

Turning the TV On and Off

Press the POWER button on the remote control. You can also use the POWER button on the TV.

It may take a while for your TV to power on.

Changing Channels

Using the Channel Buttons

❑

Press the CH or CH button to change channels.

When you press the CH or CH button, the TV changes channels in sequence. You will see all the channels that the TV has memorized. (The TV must have memorized at least three channels). You will not see channels that were either erased or not memorized. See page 21 to memorize channels.

Using the Number Buttons

❑

Press the number buttons to go directly to a channel. For example, to select channel “27”, press “2”, then “7”.

For quick channel change, press the number buttons, then press the ENTERE button.

Using the “ ” Button

❑

The “ ” button is used to select stations that broadcast a digital signal.

1. For example, for Channel "7-1", press "7", then " ”, then ", then "1".

HD indicates the TV is receiving a Digital High Denition signal. SD indicates the TV is receiving a Standard Denition signal.

For quick channel change, press the number buttons, then press the ENTERE button.

Using the PRE-CH Button to select the Previous Channel

❑

1. Press the PRE-CH button. The TV will switch to the last channel viewed.

To quickly switch between two channels that are far apart, tune to one channel, then use the number button to select the second channel. Then use the PRE-CH button to quickly alternate between them.

Adjusting the Volume

Using the Volume Buttons

❑

1. Press the VOL or VOL button to increase or decrease the volume.

❑

Using the M MUTE Button

At any time, you can cut off the sound using the MMUTE button.

1. Press MMUTE button and the sound cuts off.

The M will displayed on the screen.

2. To turn mute off, press the MMUTE button again, or simply press the VOL or VOL button.

Using the TOOLS Button

You can use the TOOLS button to select your frequently used functions quickly and easily. The Tools menu changes depending on which external input mode you are viewing.

1. Press the TOOLS button. The Tools menu will appear.

2. Press the ▲/▼ button to select a menu, then press the ENTERE button.

3. Press the ▲/▼/◄/►/ENTERE buttons to display, change, or use the selected items.

For a more detailed description of each function, refer to the corresponding page.

Anynet+ (HDMI-CEC), see page 44

• Sound Mode, see page 29

• Sleep Timer, see page 34

• Add to Favorite (or Delete from Favorite), see page 20

• Switch to Cable (or Air), see page 21

• Auto Adjustment, see page 28

•

Anynet+ (HDMI-CEC)

Sound Mode : Custom

Sleep Timer : Off

Add to Favorite

Switch to Cable

Tools

U Move

Enter

Using the Remote Control Backlight Buttons

Use this feature in dark surroundings and when you are unable to see the remote control buttons clearly.

1. Press the ON/OFF( ) light button When ON, the button backlight is turned on for a moment.

Pressing a remote control button when the remote control is on turns the button backlight on for a moment.

If you touch or move the remote control and the motion is detected by the sensor of the remote control, the button backlight will be turned on for a moment.

The button backlight will not be turned on when the remote control is turned off.

Exit

Viewing the Display

The display identifies the current channel and the status of certain audio-video settings.

1. Press the INFO button on the remote control. The TV will display the channel, the type of

sound, and the status of certain picture and sound settings.

Press the INFO button once more or wait approximately 10 seconds and it disappears

automatically.

English - 18

TV #1

DTV Air

13-1

Dolby Digital

Next Program

Fri, Dec 19 2:05 am

M. Spillane’s Mike Hammer

Bonocrunch

Prison Break

1:55 am - 2:55 am

1080i 16:9 English

2:55 am - 3:55 am

Viewing the Menus

English - 19

Before using the TV, follow the steps below to learn how to navigate the menu in order to select and adjust different functions.

1. Press the MENU button.

The main menu is displayed on the screen. Its left side has the following icons: Picture, Sound, Channel , Setup, Input, Application, Support.

2. Press the ▲ or ▼ button to select one of the icons.

Press the ◄ or ► button to access the icon’s sub-menu.

3. Press the ▲ or ▼ button to move to items in the menu.

Press the ENTERE button to enter items in the menu.

4. Press the ▲/▼/◄/► button to change the selected items.

Press the RETURN button to return to the previous menu.

5. Press the EXIT button to exit from the menu.

Using the remote control buttons

Button Operations Button Operations

MENU Display the main on-screen menu.

RETURN Return to the previous menu.

EXIT Exit the on-screen menu.

Example: Setting the TV’s Brightness in the Picture Menu

❑

Adjusting the Brightness to 80



1. Press the MENU button to display the menu.

▲/▼/◄/►/

ENTERE

Move the cursor and select an item.

Select the currently selected item.

Confirm the setting.

Picture

Mode : Standard

Cell Light : 4

Contrast : 95

Brightness : 45

Sharpness : 50

Color : 50

Tint (G/R) : G50/R50

2. Press the ENTERE button to select Picture.

3. Press the ▲ or ▼ button to select Brightness.

4. Press the ENTERE button.

5. Press the ◄ or ► button until the Brightness changes to 80.

6. Press the ENTERE button.

Press the EXIT button to exit from the menu.

Picture

Mode

Cell Light : 4

Contrast : 95

Brightness : 45

Sharpness : 50

Color : 50

Tint (G/R) : G50/R50

Cell Light : 4

Picture

Contrast : 95

Brightness : 45

Sharpness : 50

Color : 50

Tint (G/R) : G50/R50

Advanced Settings

Picture Options

Picture Reset

Brightness

Move

Brightness

Move

Adjust

Standard

Enter

►

Return

Plug & Play Feature

When the TV is initially powered on, basic settings proceed automatically and subsequently.

The Screen Saver is activated if there is no remote control key input for longer than 1 minute while Plug & Play is running.

The Screen Saver is activated if there is no operating signal for longer than 15 minutes.

1. Press the POWER button on the remote control.

The message Menu Language, Store Demo, Channels, and Time will be set. is displayed.

Menu Language, Store Demo, Channels, and Time will be set.

2. Press the ENTERE button, then Sets the menu language. menu is automatically

displayed. Press the ENTERE button.

Press the ▲ or ▼ button to select language, then press the ENTERE button. The

message Select ‘Home Use’ when installing this TV in your home. is displayed.

3. Press the ◄ or ► button to select Store Demo or Home Use, then press the ENTERE

button. We recommend setting the TV to Home Use mode for the best picture in your home environment.

Store Demo mode is only intended for use in retail environments.

Select the Antenna source to memorize.

Air

Cable

Auto

If the unit is accidentally set to Store Demo mode and you want to return toreturn to Home Use (Standard): Press the Volume button on the TV. When the volume OSD is displayed, press and hold the MENU button on the TV for 5 seconds.

4. The message Select the Antenna source to memorize. is displayed.

Press the ▲ or ▼ button to memorize the channels of the selected connection. Press

Auto Program in Progress.

DTV Air : -- Air : -DTV Cable : -- Cable : --

the ENTERE button to select Start.

Air: Air antenna signal.

•

Cable: Cable antenna signal.

•

Auto: Air and Cable antenna signals.

•

In Cable mode, you can select the correct signal source among STD, HRC, and

IRC by pressing the ▲, ▼, ◄ or ► button, then press the ENTERE button. If you have Digital cable, select the cable system signal source for both Analog and Digital. Contact your local cable company to identify the type of cable system that exists in your particular area.

5. The TV will begin memorizing all of the available channels.

To stop the search before it has nished, press the ENTERE button with Stop selected.

After all the available channels are stored, it starts to remove scrambled channels. The Auto program menu then reappears.

Press the ENTERE button when channel memorization is complete.

6. The message Set the Clock Mode. is displayed. Press the ENTERE button.

Press the ▲ or ▼ button to select Auto, then Press the ENTERE button. The message Set to daylight saving time. is displayed. If you select Manual, Set current date and time is displayed. For detailed descriptions about the Manual, refer to page 34.

7. Press the ▲ or ▼ button to select Off, On, or Auto, then press the ENTERE button.

The image to select time zone in which you live is automatically displayed.

8. Press the ▲ or ▼ button to Select the time zone, then press the ENTERE button.

If you have received a digital signal, the time will be set automatically. If not, see page 34 to set the clock.

9. The brief instruction on How to get the best performance from your new HDTV is displayed.

Press the ENTERE button.

You can access the HD Connection Guide in the Support menu.

10. Press the ENTERE button. The message Enjoy your TV. is displayed.

When you have nished, press the ENTERE button.

Plug & Play

Start

Plug & Play

U Move

Plug & Play

Stop

Plug & Play

Enjoy your TV.

Enter

Air 4

Enter

Start

Skip

If you want to reset this feature...

1. Press the MENU button to display the menu. Press the ▲ or ▼ button to select Setup,

then press the ENTERE button.

2. Press the ENTERE button again to select Plug & Play. For further details on setting

up options, press the ENTERE button again.

The Plug & Play feature is only available in the TV mode.

English - 20

Setup

Plug & Play

Language : English

Time

Game Mode : Off

V-Chip

Caption

Melody : Medium

►

Channel Control

English - 21

Storing Channels

Antenna→Air/Cable

❑

Before your television can begin memorizing the available channels, you must specify the type of signal source that is connected to the TV (i.e. an Air or a Cable system).

Press the TOOLS button to display Tools menu.

You can also switch the antenna by selecting Tools → Switch to Cable (or Air)

Auto Program

❑

Air: Air antenna signal.

•

Cable: Cable antenna signal.

•

Auto: Air and Cable antenna signals

•

STD, HRC and IRC identify various types of cable TV systems. Contact your local cable company to identify the type of cable

system that exists in your particular area. At this point the signal source has been selected. After all the available channels are stored, it starts to remove scrambled channels.

The Auto program menu then reappears. If you want to stop Auto Programming, press the ENTERE button.

The Stop Auto Program? message will be displayed. Select Yes by pressing the

◄ or ► button, then press the ENTERE button.

Clearing Scrambled Channel (Digital)

❑

The Clear Scrambled Channel function is used to lter out scrambled channels after Auto Program is completed.

This process may take up to 20~30 minutes.

To stop searching scrambled channels: Press the ENTERE button to select Stop.

Press the ◄ button to select Yes, then press the ENTERE button. This function is only available in Cable mode.

Channel

Antenna : Air

Auto Program

Clear Scrambled Channel

Channel List

Fine Tune

Clear Scrambled Channel

Removing scrambled channel.

Stop

DTV Cable 122 3%

Return

Enter

►

Fine Tune (Analog)

❑

Use ne tuning to manually adjust a particular channel for optimal reception.

If you do not store the ne-tuned channel in memory, adjustments are not saved.

“*” will appear next to the name of ne-tuned channels.

To reset the ne tuning setting, press the ▼ button to select Reset, then press the

ENTERE button.

Air 8*

UMove

Fine Tune

Reset

L Adjust

Managing Channels

Channel List

❑

Using this menu, you can Add / Delete or set Favorite channels and use the program guide for digital broadcasts.

Press the CH LIST button on the remote control to bring up the channel lists.

All Channels: Shows all currently available channels.

•

Added Channels: Shows all added channels.

•

Favorite: Shows all favorite channels.

•

Programmed: Shows all current reserved programs.

•

Using the Color buttons with the Channel List



Green (Zoom): Enlarges or shrinks a channel number.

•

Yellow (Select): Selects multiple channel lists.

•

TTOOLS (Tools): Displays the Add (or Delete), Add to Favorite (or Delete from Favorite), Timer Viewing, Channel Name

•

Edit, Select All, Deselect All, and Auto Program menus (The Options menus may differ depending on the situation.) Channel Status Display Icons

A channel set as a Favorite.

♥

)

A reserved program

A channel selected by pressing the yellow button.

(

A program currently being broadcast.

Fine Tuned

Save

Return

Continued...

Channel List Option Menu (in All Channels / Added Channels / Favorite)

❑

Press the TOOLS button to use the option menu.

Option menu items may differ depending on the channel status.

Add / Delete



You can delete or add a channel to display the channels you want.

All deleted channels will be shown on All Channels menu.

A gray-colored channel indicates the channel has been deleted.

The Add menu only appears for deleted channels.

You can also delete a channel to the Added Channels or Favorite menu in the same

manner.

Add to Favorite / Delete from Favorite



You can set channels you watch frequently as favorites.

Press the TOOLS button to display Tools menu. You can also set the favorite channel by selecting Tools

→ Add to Favorite (or Delete from Favorite)

The “♥” symbol will be displayed and the channel will be set as a favorite.

All favorite channels will be shown on Favorite menu.

N O

To select the favorite channels you have set up, press the FAV.CH button on the remote control.

Timer Viewing



If you reserve a program you want to watch, the channel is automatically switched to the reserved channel in the Channel List; even when you are watching another channel.

To reserve a program , set the current time rst.

Only memorized channels can be reserved.

You can set the channel, day, month, year, hour and minute directly by pressing the

number buttons on the remote control. Reserving a program will be shown on Programmed menu.

Digital Program Guide and Viewing Reservation: When a digital channel is

selected, and you press the ► button, the Program Guide for the channel appears. You can reserve a program according to the procedures described above.

All Channels

Air Zoom

All Channels

Air Zoom

All Channels

Air Zoom

6 Air

6-1 ♥ TV #6

7 Air

7-1 ♥ TV #7

9 Air

9-1 ♥ TV #9

10 Air

10-1 ♥ TV #10 11-1 ♥ TV #11

19 Air

Select T Tools

6 Air

6-1 ♥ TV #6

7 Air

7-1 ♥ TV #7

9 Air

9-1 ♥ TV #9

10 Air

10-1 ♥ TV #10 11-1 ♥ TV #11

19 Air

Select T Tools

6 Air

6-1 ♥ TV #6

7 Air

7-1 ♥ TV #7

9 Air

9-1 ♥ TV #9

10 Air

10-1 ♥ TV #10 11-1 ♥ TV #11

19 Air

Select T Tools

Delete Add to Favorite Timer Viewing Channel Name Edit Select All Auto Program

Select All / Deselect All



Select All: You can select all the channels in the channel list.

•

Deselect All: You can deselect all the selected channels in the channel list.

• You can perform the add / delete, add to Favorite / delete from Favorite function for multiple channels at the same time. Select

the required channels and press the yellow button to set all the selected channels at the same time. The c mark appears to the left of the selected channels.

You can only select Deselect All when there is a selected channel.

Channel Name Edit (Analog)



Channels can labeled so that their call letters appear whenever the channel is selected.

The names of digital broadcasting channels are automatically assigned and cannot be labeled.

Channel List Option Menu (in Programmed)

❑

You can view, modify or delete a reservation.

Press the TOOLS button to use the option menu.

Change Info



Programmed

9/20/2009

5:02 pm 3

9/19/2009

5:20 pm

Change Info Cancel Schedules Information Select All

Select to change a viewing reservation.

Cancel Schedules



Air Zoom

Select T Tools E Information

Select to cancel a viewing reservation.

Information



Select to view a viewing reservation. (You can also change the reservation information.)

Select All / Deselect All



You can select (or deselect) all channels in the channel list.

English - 22

Picture Control

English - 23

Changing the Picture Settings

Mode

❑

You can select the type of picture which best corresponds to your viewing requirements.

Dynamic: Select a high-definition picture for bright environments.

• Standard: Selects the optimal picture display for normal environments.

• This setting is convenient for most situations.

Movie: Selects a comfortable picture display for dark environments.

•

Cell Light / Contrast / Brightness / Sharpness / Color / Tint (G/R)

❑

Your television has several setting options that allow you to control the picture quality.

Cell Light: Adjusts the pixel brightness. 10 is the brightest setting.

• Contrast: Adjusts the contrast level.

• Brightness: Adjusts the brightness level.

• Sharpness: Adjusts the sharpness.

• Color: Adjusts the color saturation of the picture using the bar on the screen.

• Tint (G/R): The closer to Red 100, the more saturated the red color becomes.

• When you make changes to Cell Light, Contrast, Brightness, Sharpness, Color, or

Tint (G/R), the OSD will be adjusted accordingly. When in PC mode, Tint (G/R), Sharpness and Color are not available.

Settings can be adjusted and stored for each external device you have connected to

an input of the TV.

The energy consumed during use can be signicantly reduced if the brightness level

is lowered, which will reduce the overall running cost.

Picture

Mode

Cell Light : 4

Contrast : 95

Brightness : 45

Sharpness : 50

Color : 50

Tint (G/R) : G50/R50

Mode : Standard

Picture

Cell Light : 4

Contrast : 95

Brightness : 45

Sharpness : 50

Color : 50

Tint (G/R) : G50/R50

Advanced Settings

Standard

►

Advanced Settings

❑

You can adjust the detailed settings for your screen including the color and contrast.

Advanced Settings is available in Standard or Movie mode.

In PC mode, you can only make changes to Gamma and

White Balance from among the Advanced Settings items.

Black Tone



You can select the black level on the screen to adjust the screen depth.

Off: Turns the Black Adjust function off.

• Dark: Sets the black color depth to dark.

• Darker: Sets the black color depth to darker.

• Darkest : Sets the black color depth to darkest.

•

Dynamic Contrast



Black Tone : Off ►

Dynamic Contrast : Medium

Gamma : 0

Color Space : Native

White Balance

Flesh Tone : 0

Edge Enhancement : On

Advanced Settings

Move

You can adjust the screen contrast so that the optimal contrast is provided.

Off: Turns the Dynamic Contrast function off.

• Low: Sets Dynamic Contrast to low.

• Medium: Sets Dynamic Contrast to medium.

• High: Sets Dynamic Contrast to high.

•

Gamma



You can adjust the Primary Color (Red, Green, Blue) Intensity.

Color Space



Color Space is a color matrix composed of red, green and blue colors. Select your favorite color space to experience the most natural color.

Native: Sets the color range wider than that of the input video source.

• Auto: Automatically sets the color range depending on the input video source.

•

ReturnEnter

Continued...

White Balance



You can adjust the color temperature for more natural picture colors.

R-Offset: Adjust the low level red intensity.

• G-Offset: Adjust the low level green intensity.

• B-Offset: Adjust the low level blue intensity.

• R-Gain: Adjusts the high level red intensity.

• G-Gain: Adjusts the high level green intensity.

• B-Gain: Adjusts the high level blue intensity.

• Reset: Resets the default white balance.

• Changing the adjustment value will refresh the adjusted screen.

Flesh Tone



You can emphasize the pink esh tone in the picture.

Changing the adjustment value will refresh the adjusted screen.

EdgeEnhancement→Off/On



You can emphasize object boundaries in the picture.

Advanced Settings

Black Tone : Off

Dynamic Contrast : Medium

Gamma : 0

Color Space : Native

White Balance ►

Flesh Tone : 0

Edge Enhancement : On

Move

ReturnEnter

Picture Options

❑

In PC mode, you can only make changes to the Color Tone, Size and Screen Burn

Protection from among the items in Picture Options.

ColorTone→Cool/Normal/Warm1/Warm2



You can select the most comfortable color tone for viewing.

Warm1 or Warm2 is only activated when the picture mode is Movie.

Settings can be adjusted and stored for each external device you have connected to

an input of the TV.

Size



Occasionally, you may want to change the size of the image on your screen. Your TV

comes with six screen size options, each designed to work best with specic types

of video input. Your satellite receiver may have its own set of screen sizes as well. In general, though, you should view the TV in 16:9 mode as much as possible.

16:9 : Sets the picture to the 16:9 aspect ratio.

• Zoom1: Stretches the 16:9 aspect ratio picture vertically.

• Zoom2: Stretches the Zoom 1 picture vertically.

• Wide Fit: Stretches the picture both horizontally and vertically to display the optimal

• picture.

4:3: Sets the picture to the 4:3 aspect ratio.

• Screen Fit: Displays the full native HD signal that cannot be viewed using a normal TV.

•

Alternately, you can press the P.SIZE button on the remote control repeatedly to change the picture size.

Tint (G/R) : G50/R50

Advanced Settings

Picture

Picture Options

Picture Reset

Picture Options

Color Tone : Normal ►

Size : 16:9

Digital NR : Auto

HDMI Black Level : Normal

Film Mode : Off

Screen Burn Protection

Move

►

ReturnEnter

16:9 Zoom1 Zoom2

Wide Fit 4:3 Screen Fit

Temporary image retention may occur when viewing a static image on the set for more than two hours.

After selecting Zoom1, Zoom2 or Wide Fit:

Press the ◄ or ► button to select Position, then press the ENTERE button. Press the ▲ or ▼ button to move the picture up and down.

After selecting Screen Fit in HDMI (1080i/1080p) or Component (1080i/1080p) mode, you may made need to center the picture:

Press the ◄ or ► button to select Position, then press the ENTERE button. Press the ▲, ▼, ◄ or ►button to move the picture. Reset: Press the ◄ or ► button to select Reset, then press the ENTERE button. The TV will be reset to 16:9.

HD (High Denition): 16:9 - 1080i/1080p (1920x1080), 720p (1280x720)

English - 24

Continued...

Settings can be adjusted and stored for each external device you have connected to an input of the TV.

English - 25

In PC Mode, only 16:9 and 4:3 mode can be adjusted. Settings can be adjusted and stored for each external device you have connected to an input of the TV.

Input Source Picture Size

ATV, Video, Component (480i, 480p) 16:9, Zoom1, Zoom2, 4:3

Component (720p)

16:9, Wide Fit, 4:3

DTV(1080i), Component (1080i, 1080p), HDMI (720p, 1080i, 1080p) 16:9, 4:3, Wide Fit, Screen Fit PC 16:9, 4:3

Digital NR



If the broadcast signal received by your TV is weak, you can activate the Digital Noise Reduction feature to help reduce any static and ghosting that may appear on the screen.

Off: Turns the Digital NR function off.

•

Low: Sets Digital NR to low.

•

Medium: Sets Digital NR to medium.

•

High: Sets Digital NR to high.

•

Auto: Sets Digital NR to Auto.

•

HDMI Black Level



You can directly select the black level on the screen to adjust the screen depth.

Normal: The screen gets brighter.

•

Low: The screen gets darker.

• This function is active only when an external device is connected to the TV via HDMI.

HDMI Black Level function may not be compatible with all external devices.

Film Mode



The TV can be set to automatically sense and process lm signals from all sources and

Tint (G/R) : G50/R50

Advanced Settings

Picture

Picture Options

Picture Reset

Picture Options

Color Tone : Normal

Size : 16:9

Digital NR : Auto ►

HDMI Black Level : Normal

Film Mode : Off

Screen Burn Protection

adjust the picture for optimum quality.

Off: Basic video image processing applied and No auto-detection for lm-based

• programs.

Auto: Automatically adjusts for the best image quality between lm and video programs.

•

Cinema Smooth: Cinema Smooth reproduces lm cinema video with greatly reduced or without visible motion judder, as you

•

Move

see it in the movie theater. (PN50B560T5F/PN58B560T5F/PN63B590T5F only) Only if HDMI 1080p 24Hz signal is input, Cinema Smooth function is activated and you can set ON/OFF.

Film mode is supported in TV, Video, Component (480i / 1080i) and HDMI (1080i).

Screen Burn Protection



Congures the Screen Burn Protection options to prevent and reduce pixel burn. When an image remains in one position too long, it may cause a permanent burn on the screen.

Preventing Screen Burn-in

Screen Burn Protection

Pixel Shift ► Scrolling Side Gray : Dark

Move

To reduce the possibility of screen burn, this unit is equipped with screen burn prevention technology. This technology enables you to set picture movement up/down (Vertical Line) and side to side (Horizontal Dot). The Time setting allows you to program the time between movement of the picture in minutes.

Pixel Shift : Using this function, you can minutely move pixels on the PDP in horizontal or vertical direction to prevent after-

• images on the screen.

Optimum condition for pixel shift;

Item TV/AV/Component/HDMI/PC

Horizontal 0~4 4

Vertical 0~4 4

Time(min) 1~4min. 2 min

►

ReturnEnter

Side Gray : When you watch TV with the screen ratio of 4:3, the screen is prevented from any damage by adjusting the white

• balance on both extreme left and right sides. To prevent the screen burn from happening, select Dark or Light.

Dark: When you set the screen ratio to 4:3, it darkens the left and right sides.

Light: When you set the screen ratio to 4:3, it brightens the left and right sides.

Reducing the Effects of Screen Burn

If screen burn has occurred, you can select Scrolling to help remove screen burn artifacts.

Scrolling : This function removes after-images on the screen by moving all the pixels on the PDP according to a pattern. Use

• this function when there are remaining after-images or symbols on the screen, especially when you displayed a still image on the screen for a long time.

The after-image removal function has to be executed for a long time (approximately 1 hour) to effectively remove afterimages on the screen. If the after-image is not removed after performing the function, repeat the function again.

Press any key on the remote control to cancel this feature.

PictureReset→ResetPictureMode/Cancel

❑

Resets all picture settings to the default values.

Select a picture mode to be reset. The reset is performed for each picture mode.

Picture

Advanced Settings

Picture Options

Picture Reset

►

English - 26

PC Display

English - 27

Using Your TV as a Computer (PC) Display

Setting Up Your PC Software (Based on Windows XP)



The Windows display-settings for a typical computer are shown below. The actual screens on your PC will probably be different, depending upon your particular version of Windows and your particular video card. However, even if your actual screens look different, the same basic set-up information will apply in almost all cases. (If not, contact your computer manufacturer or Samsung Dealer.)

1. First, click on Control Panel on the Windows start menu.the Windows start menu.

2. When the control panel window appears, click on Appearance and Themes and a display

dialog-box will appear.

3. When the control panel window appears, click on Display and a display dialog-box will

appear.

4. Navigate to the Settings tab on the display dialog-box. The correct size setting (resolution)

Optimum : 1920 X 1080 pixels. If a vertical frequency option exists on your display settings dialog box, the correct value is 60 or 60 Hz. Otherwise, just click OK and exit the dialog box.

Display Modes

If the signal from the system equals the standard signal mode, the screen is adjusted automatically. If the signal from the system doesn’t equal the standard signal mode, adjust the mode by referring to your videocard user guide; otherwise there may be no video. For the display modes listed below, the screen image has been optimized during manufacturing.



D-Sub and HDMI/DVI Input

Mode Resolution Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Clock Frequency (MHz) Sync Polarity (H/V)

IBM

MAC

VESA CVT

VESA DMT

VESA GTF

VESA DMT /

DTV CEA

When using an HDMI/DVI cable connection, you must use the HDMI IN 2(DVI) terminal.

640 x 350 720 x 400

640 x 480 832 x 624

1152 x 870

720 x 576 1152 x 864 1280 x 720 1280 x 720 1280 x 960

640 x 480

800 x 600

800 x 600 1024 x 768 1024 x 768 1024 x 768 1152 x 864 1280 x 800 1280 x 800 1280 x 960

1280 x 1024 1280 x 1024

1360 x 768 1440 x 900 1440 x 900

1680 x 1050

1280 x 720

1280 x 1024

1920 x 1080p 67.500 60.000 148.500 + / +

31.469

35.000

49.726

68.681

35.910

53.783

44.772

56.456

75.231

31.469

37.861

37.500

37.879

48.077

46.875

48.363

56.476

60.023

67.500

49.702

62.795

60.000

63.981

79.976

47.712

55.935

70.635

65.290

52.500

74.620

70.086

70.087

66.667

74.551

75.062

59.950

59.959

59.855

74.777

74.857

59.940

72.809

75.000

60.317

72.188

75.000

60.004

70.069

75.029

75.000

59.810

74.934

60.000

60.020

75.025

60.015

59.887

74.984

59.954

70.000

25.175

28.322

30.240

57.284

100.000

32.750

81.750

74.500

95.750

130.000

25.175

31.500

40.000

50.000

49.500

65.000

75.000

78.750

108.000

83.500

106.500

108.000

135.000

85.500

106.500

136.750

146.250

89.040

128.943

+ / -

- / +

- / -

- / +

- / -

- / + / + + / + + / +

- / -

- / + / + + / +

- / +

- / + + / + + / + + / + + / +

- / +

- / -

Setting up the TV with your PC

Auto Adjustment

❑

Use the Auto Adjust function to have the TV set automatically adjust the video signals

it receives. The function also automatically ne-tunes the settings and adjusts the

frequency values and positions.

Press the TOOLS button to display Tools menu.

You can also set the Auto Adjustment by selecting Tools → Auto Adjustment.

Preset: Press the SOURCE button to select PC mode.

This function does not work in DVI-Digital mode.

❑

Screen

The purpose of the picture quality adjustment is to remove or reduce picture noise. If the

noise is not removed by ne tuning alone, then make the vertical frequency adjustments on your PC and ne tune again.

After the noise has been reduced, re-adjust the picture so that it is aligned on the center of the screen.

Preset: Press the SOURCE button to select PC mode.

Coarse



Adjusts the frequency when vertical noise appears on the screen.

Fine



Adjusts the screen to be clearer.

PC Position



Adjust the PC’s screen positioning if it does not t the TV screen. Press the ▲ or ▼ button to adjusting the Vertical-Position. Press the ◄ or ►button to adjust the

Horizontal-Position.

Image Reset



You can replace all image settings with the factory default values.

Picture

Coarse

Fine

PC Position

Image Reset

Brightness : 45

Sharpness : 50

Auto Adjustment

Screen

Advanced Settings

Picture Options

Picture Reset

Screen

Move

PC Position

Move

50 ►

ReturnEnter

►

English - 28

Sound Control

English - 29

Changing the Sound Settings

Mode

❑

You can select the sound mode to best suit the programming you’re watching.

Standard: This sound mode is for general purposes.

•

Music: Music mode enables you to listen to music as if you are sitting in a concert

• hall.

Movie: Movie mode enables you to experience live and full movie sound as if you are

• sitting in a movie theater.

Clear Voice: Emphasizes voice over other sounds. Select this sound mode when

• watching news, soap operas, or documentaries.

Custom: You can customize the sound settings to suit your personal preferences.

•

Press the TOOLS button to display Tools menu. You can also set the sound mods by selecting Tools → Sound Mode

Equalizer

❑

The sound settings can be adjusted to suit your personal preferences.

Mode: Selects the sound mode among the predened settings.

• Balance L/R: Adjusts the balance between the right and left speaker.

• 100Hz, 300Hz, 1kHz, 3kHz, 10kHz (Bandwidth Adjustment): Adjusts the level of

• different bandwidth frequencies.

Reset: Resets the equalizer settings to the default values.

•

SRSTruSurroundHD→Off/On

❑

SRS TruSurround HD enables you to enjoy a virtual 5.1 Surround Sound effect over the TV's two speakers. This function provides not only rich deep bass also improves high frequency resolution.

You can select these options simply by pressing the SRS button on the remote

control.

Sound

Mode

: Custom

Equalizer

SRS TruSurround HD : Off

Preferred Language : English

Multi-Track Sound : Stereo

Auto Volume : Off

Speaker Select : TV Speaker

Equalizer

Mode : Custom

Balance L R

100Hz - +

300Hz - +

1kHz - +

3kHz - +

10kHz - +

▼

AdjustMove

►

ReturnEnter

TruSurround HD, SRS and the symbol are trademarks of SRS Labs, Inc. TruSurround HD technology is incorporated under license from SRS Labs, Inc.

Preferred Language (Digital)

❑

Digital-TV broadcasts are capable of simultaneous transmission of many audio tracks (for example, simultaneous translations of the program into foreign languages).

You can only select the language from among the actual languages being broadcast.

You can listen in a language other than the Preferred Language by pressing the MTS button on the remote control.

Multi-Track Sound (MTS) (Analog)

❑

Mono: Choose for channels that are broadcasting in mono or if you are having difculty receiving a stereo signal.

• Stereo: Choose for channels that are broadcasting in stereo.

• SAP: Choose to listen to the Separate Audio Program, which is usually

• a foreign-language translation.

Depending on the particular program being broadcast, you can listen to Mono,

Stereo, or SAP.

Press the MTS button on the remote control repeatedly to select Mono, Stereo, or SAP.

AutoVolume→Off/On

❑

Each broadcasting station has its own signal conditions, and so it is not easy to adjust the volume every time the channel is changed. This feature lets you automatically adjust the volume of the desired channel by lowering the sound output when the modulation signal is high or by raising the sound output when the modulation signal is low.

Continued...

❑

Speaker Select

When you watch TV with it connecting to a Home theater, turn the TV speakers off so you can listen to sound from the Home theater’s (external) speakers.

External Speaker: Uses the external speakers(Home Theater) to output sound.

• TV Speaker: Uses the TV speakers to output sound.

•

If you select External Speaker in the Speaker Select menu, the sound settings will be limited.

The volume buttons and MMUTE buttons do not operate when the Speaker Select is set to External Speaker. Please set the volume on your Home theater.

TV's Internal Speakers Audio Out (Optical, L / R Out) to Sound System

TV / AV / Component / PC / HDMI TV / AV / Component / PC / HDMI

TV Speaker Speaker Output Sound Output

External Speaker Mute Sound Output

Video No Signal Mute Mute

Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby Laboratories.

Sound Reset

❑

You can restore the Sound settings to the factory defaults.

Reset All: All the sound values return to default settings.

• Reset Sound Mode: Current sound values return to default settings.

• Cancel: Select the sound reset options.

•

Multi-Track Sound : Stereo

Auto Volume : Off

Sound

Speaker Select : TV Speaker

Sound Reset

►

Function Description

Configuring the Setup Menu

Language

❑

You can set the menu language.

GameMode→Off/On

❑

When connecting to a game console such as PlayStationTM or XboxTM, you can enjoy a more realistic gaming experience by selecting the game menu.



When the Game Mode is On

Picture mode is automatically changed to Standard and cannot be changed.

• Sound mode is automatically changed to Custom and cannot be changed. Adjust the

• sound using the equalizer.

The Reset in the Sound menu is activated. Reset function initializes the Equalizer settings to the factory default setting.

•

Game Mode is not available in regular TV mode or Game Mode set to Off.

If the picture is poor when an external device is connected to the TV, check if Game Mode is On.

If you display the TV menu in Game mode, the screen shakes slightly.

The mark ( ) appears on the screen which means that Game Mode is on with the selected source.

This function supports only game function.

Game mode is not available in PC mode.

Setup

Plug & Play

Language : English

Time

Game Mode : Off

V-Chip

Caption

Melody : Medium

Energy Saving : Off

►

English - 30

Continued...

+ 77 hidden pages