Samsung PN58C8000YFXZA User Manual

Quick Setup Guide

Congratulations on the purchase of your new Samsung TV. Read this setup guide to get your TV up and running quickly.

STOP

Please do not return this unit.

If you have problems operating your

1-800-SAMSUNG (1-800-726-7864)

TV, call:

For web support please visit:

www.samsung.com/support

Step 1: Install the Stand

Follow the steps below to connect the TV to the stand. (50 inch model only)

✎

NOTE

Make sure to distinguish between the front and back of the Stand and

Guide Stand when assembling them.

Make sure that at least two persons lift and move the PDP T V.

Stand the product up and fasten the screws. If you fasten the screws with

the PDP TV placed down, it may lean to one side.

1 Connect the Guide Stand to the

Stand using ﬁve screws (M4 X L12) as shown.

2 With your TV upright, connect the

TV to the Stand.

Rear

Step 2: Install the Batteries into the Remote

To install batteries into your remote control, follow these steps:

1. Lift the cover on the back of the remote

upward as shown in the ﬁgure to the right.

2. Install two AAA batteries.

✎

Make sure to match the + and ends of the batteries to the diagram in the battery compartment.

3. Replace the cover.

Step 3: Connect Power and Antenna or Cable

1-800-SAMSUNG (1-800-726-7864) Samsung Electronics America, Inc. 85 Challenger Road Ridgeﬁeld Park, NJ 07660-2112 Samsung Electronics Canada Inc. 55 Standish Court Mississauga, Ontario L5R 4B2 Call Center hours of operation: Mon-Sun, 9:00 AM -12 AM EST. To register this product, visit: www.samsung.com/ register.

Screws (M4 X L12)

Guide Stand

Stand

Rear

3 Fasten two screws (M4 X L10) at

position 1, and then fasten three screws (M4 X L10) at position 2.

Screws (M4 X L10)

VHF/UHF Antenna

Antenna Cable (Not Supplied)

Use a 75 ohm (round) cable.

Connect Ant In to

• Wall cable jack

• VHF/UHF Antenna

• Cable or Satellite box Ant or Cable Out

Top view

Front

Rear

Step 4: Connect External Devices

Connecting an AV device (DVD/Blu-ray player, cable/satellite box, etc.)

Use one of the connections below to connect your TV to an external A/V device.

We recommend using HDMI for the highest picture quality.

✎

When connecting to AV IN, the color of the

AV IN [Y/VIDEO] jack (green) will not match the

video cable (yellow).

Lowest Quality Connection

Audio/Video connection (480i only)

Audio Cable (Not Supplied)

Video Cable (Not Supplied)

Step 5: Run Plug & Play

When you turn on your TV for the ﬁrst time, it automatically launches the Plug & Play function. With Plug & Play, you can select the On Screen Display language, set the clock mode, and launch the TV’s channel memorizing process.

It also displays connection instructions similar to those in this guide. To navigate while Plug & Play is running, press the Up, Down, Left or Right arrow

buttons on your remote. To make a selection, press the ENTER To skip a screen, press the MENU button. To turn on your TV, press the POWER

button on the remote or on the TV. To run Plug & Play, follow these steps:

1 Using your remote control,

select the language for the On Screen Display (OSD), and then press the ENTERE button.

Select Language of the OSD.

Menu Language :

2 Select Home Use, and then

press the ENTER If you select Store Demo, the TV will reset your picture and audio settings every 30 minutes.

button.

Using an Audio/Video Cable

AUDIO OUT

VIDEO OUT

DVD, Blu-ray player, cable box, STB satellite receiver, VCR

Device

button.

Plug & Play

English

Español

Français

Move

Enter

6 Select the Daylight savings time setting: Off or On, and then press the

7 Select the time zone in which you live, and then press the ENTER 8 After the time zone screen, The connection method for best HD screen

9 The Enjoy your TV. screen appears. Then press the ENTER

Changing the Screen Size

Your TV has several screen size options, each designed to work best with speciﬁc types of video input. If you have a cable box or satellite receiver, it may have its own set of screen sizes as well.

To change the screen size, press the P.SIZE button on your remote. The ﬁrst time you press it, your TV displays the current setting. Thereafter, each time you press the P.SIZE button, you change the size of the picture on the screen.

The following sizes are available:

3 Select Antenna Source and Channel Source. If Antenna Source is

Cable or Auto, you must select Channel Source to same type as your cable system type. After selecting source, select Search; then press the

ENTERE button on your remote.

✎

Most cable systems are Standard (STD) systems, If you are not sure about what kind of cable system you have, contact your cable company.

✎

If your TV is attached to a cable or satellite box, skip Steps 3 through 5. After Plug & Play is complete, set your T V to Channel 3 or 4, according to the directions for your cable or satellite box.

4 The TV memorizes the available channels. This process can take up to 45

minutes.

5 After the TV has memorized the channels, choose the Clock Mode. Select

Auto if you have a digital channel in your area. Select Manual if you don’t, or

if you have a cable or satellite box. When done, press the ENTERE button.

✎

If you select Manual, the clock setting screen appears.

✎

Screen Fit: Displays the full image without any cut-off when HDMI (720p / 1080i / 1080p) or Component (1080i / 1080p) signals are inputted.

Best Connection

HD connection (up to 1080p)

HDMI Cable (Not Supplied)

Using an HDMI Cable

HDMI OUT

DVD, Blu-ray player, HD cable box,

HD STB (Set-Top-Box) satellite

Device

receiver

Very Good Connection

HD connection (up to 1080p)

HDMI to DVI Cable (Not Supplied)

Audio Cable (Not Supplied)

Using an HDMI to DVI Cable

DVI OUT

AUDIO OUT

Device

Good Connection

Component connection (up to 1080p)

Component Cable (Not Supplied)

Audio Cable (Not Supplied)

Using a Component Cable

COMPONENT OUT

AUDIO OUT

DVD, Blu-ray player, cable box,

STB satellite receiver, VCR

Device

ENTERE button.

button.

quality is displayed. Press the Right arrow button on your remote to view each screen in succession. Press the Blue button to skip this section.

button.

16:9 Widescreen 4:3 Standard screen Wide Fit

Zoom 1 Zoom 2 Screen Fit

Connecting an audio device (Home Theater, etc.)

Connect your TV to your Home Theater or other audio device to enjoy enhanced Sound quality.

Audio Cable (Not Supplied)

Optical Cable (Not Supplied)

Analog Audio connection

Using an Audio Cable

Ampliﬁer / DVD home theater

AUDIO IN

Digital Audio connection

Using an Optical Cable

Digital Audio System

OPTICAL

Connecting a PC

Connect your TV to a PC to use it as a Monitor.

HD connection

Using an HDMI to DVI Cable

DVI OUT

AUDIO OUT

Using a D-Sub Cable

AUDIO OUT

PC OUT

Audio Cable (Not Supplied)

D-Sub Cable (Not Supplied)

HDMI to DVI Cable

(Not Supplied)

Audio Cable (Not Supplied)

Changing the Picture Mode

Your TV has four preset Picture Modes with factory adjusted settings, each designed to give you an excellent picture under speciﬁc conditions.

The Picture Modes are listed and described in the table below:

Mode

Dynamic

Description

Brightens picture. For a vibrant, enhanced image in brightly lit or sunny room.

Standard

Relax

Movie

CAL-NIGHT

CAL-DAY

For a bright, detailed picture in a normally lit room. For a comfortable, easy-on-the-eyes picture in a normally lit room.

For a studio quality cinema picture in a dimly lit or dark room.

Selects a custom calibrated picture for lights off theater experience.

Selects a custom calibrated picture for daylight viewing.

To change the Picture Mode, follow these steps:

1. Turn on your TV, press the TOOLS button on your remote. The Tools menu appears.

2. Using the ▲ or ▼ on your remote, select Picture Mode.

3. On the Picture Mode menu, use the ◄ or ► button on your remote to select the Picture Mode you want.

4. Press the EXIT button to exit the menu.

Setting the Clock

Before you can use your TV’s On/Off Timer, you must set the clock. To set the clock, follow these steps:

1. Turn on your TV, press the MENU button on your remote, then select Setup → Time.

2. Select Clock Mode, and then press the ENTER

3. Choose Auto or Manual.

If you select Auto, the current time will be set automatically using the time

from a digital channel.

If you select Manual, you can set the Month, Day, Year, Hour, Minute

and am/pm directly by pressing up, down, left and right arrow button on your remote.

4. Press the RETURN button on your remote when done.

button.

SUM

Step 6: Remote Control

PRE-CH

MUTE

CH LIST

SOURCE

PRE-CH

SOURCE

Remote Control Buttons and Functions

Turns the TV on and off.

Displays and selects the available video sources.

Press to directly access channels.

Press to select additional channels (digital) being

broadcasted by the same station. For example, to select

channel “54-3”, press “54”, then press “–” and “3”.

Adjusts the volume.

Brings up the OSD.

Displays the Content View, which includes Channel

List, Internet@TV, Media Play, AllShare and 3D.

Quickly select frequently used functions.

Returns to the previous menu.

These buttons are for the Channel List, Internet@TV,

Media Play menu, etc.

Use these buttons in Media Play and

Anynet+ (HDMI-CEC) modes. (�: Controls recording

for Samsung recorders that have the Anynet+ feature)

Changing Channels and Adjusting the Volume

Adjust the volume by pressing the Volume button

✎

You can also change the channels by pressing the

on the remote.

Viewing the On Screen Menus

To view the On Screen Menus, follow these steps:

1. Turn on your TV, press the MENU button on your

remote. The main menu appears. The menu’s left side has the following menu options: Picture, Sound, Channel, Setup, Input, Application, and Support.

2. Press the ▲ or ▼ button on your remote to select a menu option, and then press the ENTER

button.

3. When done using the menu, press the EXIT button on your remote to exit.

CONTENT

TOOLS

Selecting a Source

To watch a movie on your Blu-ray player or watch your favorite TV show, you must select the correct source. A source is a device, such as a Blu-ray/DVD player, a cable/satellite box, antenna or a cable TV input. Sources can be connected to your TV through the HDMI, DVI, Component, Composite, or D-sub connections, or through the Antenna or Cable In connections.

To view the signal from a source connected to the HDMI, DVI, Component, Composite, or D-sub jack, press the SOURCE button on your remote. Each time you press the SOURCE button, you change to a different source.

POWER ON/OFF

CONTENT

TOOLS

RETURN

A C DB

MEDIA.P YAHOO!

MUTE

CH LIST

button on the front panel of your TV and adjust the volume by pressing the y button.

INTERNET

INFO

SOURCE

Turns the remote control light on or off. When on, the buttons become illuminated for a moment when pressed. (Using the remote control with this button set to off will reduce the battery usage time.)

PRE-CH

MUTE

CH LIST

Returns to the previous channel.

Cuts off the sound temporarily.

Changes channels.

Displays the channel list on the screen.

INTERNET

@ TV

INFO

Link to various internet services.

Displays information on the TV screen.

Selects the on-screen menu items and changes the values

EXIT

seen on the menu.

Exits the menu.

MEDIA.P: Displays Media Play. YAHOO!: Runs the Yahoo widget.

P.SIZEFAV.CH

3D: Sets the 3D mode. FAV.CH: Displays Favorite Channel Lists on the screen. P.SIZE: Selects the picture size. CC: Controls the caption decoder.

Change the channels by pressing the Channel button on the remote.

✎

If your TV is attached to a cable or satellite box, change the channel using the box’s remote.

Using Motion Judder Canceller

Motion Judder Canceller technology virtually eliminates any blur in video that contains fast motion, such as sports and action movies. To activate Motion Judder Canceller, follow these steps:

1. Turn on your TV, press the MENU button on your remote, then select Picture Options → Motion Judder Canceller.

2. Select the Motion Judder Canceller setting you want.

✎

If Motion Judder Canceller is Demo, you can compare the difference of on and off modes.

3. Press the RETURN button on your remote when done.

Step 7: The Internet@TV and Media Play Features

Your TV’s Internet@TV feature (IPTV) lets you connect to an ever-expanding portal of your favorite on-line digital content. Customizable widgets give you access to Blockbuster, Facebook, YouTube, Flickr, Netﬂix* and more - all on your HDTV. The Media Play feature lets you connect to your PC through your home network and stream PC audio and video ﬁles to your HDTV using your remote. To use IPTV or Samsung PC Share Manager, you must connect your TV to your network. You can attach the TV to your network in two ways, by cable, using CAT 5 cable, or wirelessly, using a Samsung Wireless LAN Adapter. Instructions for both connection methods are below.

Network Connection - Wired

There are two main ways to connect your TV to your network using cable, depending on your network setup. They are illustrated below:

The Modem Port on the Wall

Modem Cable (Not Supplied)

The LAN Port on the Wall

External Modem

(ADSL / VDSL / Cable TV)

LAN Cable (Not Supplied)

Conﬁguring the Network Connection - Wired

Most home networks use the Dynamic Host Conﬁguration Protocol (DHCP) to conﬁgure network connections. Home networks that support DHCP automatically provide the IP address, subnet mask, gateway, and DNS values your TV needs to access the Internet so you don’t have to enter them manually.

Internet Protocol Setup : Auto

IP Address :

Subnet Mask :

Gateway :

DNS : Auto

DNS Server :

To conﬁgure your network connection for a network that uses DHCP, follow these steps:

1. Connect your TV to your network as shown in one of the illustrations above.

2. Turn on your TV, press the MENU button on your remote, and then select Setup → Network.

3. Set the Network Type to Wired if it is not already set to Wired.

4. Select Network Setup. The Network Setup screen appears.

5. On the Network Setup menu, set Internet Protocol Setup and DNS to Auto. Auto acquires and enters the necessary internet values automatically.

6. Select Network Test to check Internet connectivity.

✎

Some networks are Static IP networks. If your network is a Static IP network, you can not use DHCP to configure the network connection. Instead, you must enter the IP Address, Subnet Mask, Gateway, and DNS Server manually. For instructions explaining how to configure a Static IP network, see your user’s manual.

Starting Internet@TV

To view the On Screen Menus, follow these steps:

1. Turn on your TV, press the MENU button on your remote, then select Application →

Content View.

2. Press the ◄ or ►

button to select Internet@TV, then press the ENTER

button. The USER TERMS and PRIVACY POLICY windows appears, then select Yes.

3. Follow the directions on your screen to set up Internet@TV. For detailed instructions, see your Owner’s Manual.

✎

For best Internet@TV results, your broadband company should provide sustained download speeds of 3.5 mb/sec or more.

Recommended

My Applications

SettingsSamsung Apps

TV Rear Panel

Network Setup

Move

Enter

Return

by Date 1/1

Return

Network Connection - Wireless

You can connect your TV to your LAN through a standard wireless router or modem. To connect wirelessly, you must ﬁrst attach a “Samsung Wireless LAN Adapter” (WIS09ABGN, WIS09ABGN2,WIS10ABGN - sold separately) to either the

USB 1 (HDD) or USB 2 port on the back of your TV. See the illustration below.

The LAN Port on the Wall

LAN Cable (Not Supplied)

Wireless IP sharer

(AP having DHCP server)

TV Rear Panel

Samsung Wireless

LAN Adapter

Samsung’s Wireless LAN adapter is sold separately and is offered by select retailers, Ecommerce sites and Samsungparts.com. Samsung’s Wireless LAN adapter supports the IEEE 802.11A/B/G and N communication protocols. Samsung recommends using IEEE 802.11N. When you play the video over a IEEE

802.11B/G connection, the video may not play smoothly. Most wireless network systems incorporate a security system that requires devices

that access the network through an access point or AP (typically a wireless IP Sharer) to transmit an encrypted security code called an access key.

If Pure High-throughput (Greenﬁeld) 802.11n mode is selected and the Encryption type is set to WEP, TKIP or TKIPAES (WPS2Mixed) for your AP, Samsung TVs will not support a connection in compliance with new Wi-Fi certiﬁcation speciﬁcations.

Conﬁguring the Network Connection - Wireless

The instructions below are for networks that use the Dynamic Host Conﬁguration Protocol (DHCP) to conﬁgure network connections automatically. If your have a Static IP network, see your user’s manual for conﬁguration instructions. To conﬁgure your network connection for a network that uses DHCP, follow these steps:

1. Connect your TV to your network as shown in the illustrations above.

2. Turn on your TV, press the MENU button on your remote, and the select Setup → Network.

3. Set the Network Type to Wireless if it is not already set to Wireless.

4. Select Network Setup. The Network Setup screen appears.

5. On the Network Setup menu,

select an AP (Access Point) or ad hoc network. If you have selected a network with a security key, the

Security Key screen appears.

6. Enter the security key using the

numbers on the remote, and then press the Blue button on your remote.

✎

If your network uses WEP

Select a network : Not Selected

Internet Protocol Setup : Auto

IP Address :

Subnet Mask :

Gateway :

DNS : Auto

DNS Server :

Network Setup

PBC(WPS)

Move

Enter

Return

security encryption, 0~9 and A~F will be available on the Security Key screen. Use the Direction button on your remote to move to the characters and the enter key to select them.

7. On the Network Setup menu, set Internet Protocol Setup and DNS to Auto. The Auto acquires and enters the necessary internet values automatically.

8. Select Network Test to check internet connectivity.

✎

For more information, see your user’s manual.

Connecting a USB Device for Media Play

You can enjoy photo, music, and movie ﬁles stored on a USB device by connecting it to the TV and using the Media Play feature. For Media Play operating instructions, please see your Owner’s Manual.

MediaPlay

Videos

Change Device

View Devices

Enter

BN68-02619A-03

Return