Samsung P42H-2, P50H, SYNCMASTER P42H, SYNCMASTER P50H, P50HN User Manual
...
P42H, P50H, P42Hn, P50Hn
PDP MONITOR
quick start guide
ii
Introduction
Package Contents
Note
Please make sure the following items are included with your PDP Display.
If any items are missing, contact your dealer.
Contact a local dealer to buy optional items.
Note
This stand is not for the Floor Standing Type.
Unpacking
Manuals
Quick Setup Guide Warranty Card
(Not available in all loca-
Cables
D-Sub Cable Power Cord
Others
PDP Display
User's Guide
tions)
Introduction
Others
Remote Control Batteries (AAA X 2)
Ferrite Core for Power Cord
Sold separately
DVI Cable Wall Mount KIT LAN Cable
TV tuner box NetWork Box
Note
(Not available in all loca-
tions)
(Applicable to the P42H /
P50H model only)
(3301-001110)
(Applicable to the P42HN /
P50HN model only)
Semi Stand KIT
• You can purchase and connect a separate network box or TV tuner box. For information on how
to use these, refer to their respective user manuals.
• You can only connect one external box.
Ferrite Core (Power Cord)
• The ferrite cores are used to shield the cables from interference.
• When connecting a cable, open the ferrite core and clip it around the
cable near the plug.
Your PDP Display
Front
Introduction
SOURCE button [SOURCE]
Switches from PC mode to Video mode. Changing the source is only allowed for
external devices that are connected to the PDP Display at the time.
[PC] → [DVI] → [AV] → [HDMI] → [MagicInfo]
Note
• The TV menu is available when a TV tuner box is installed.
• The MagicInfo menu is available when a network box is installed in the HN
or H model.
Enter button [ ]
Activates a highlighted menu item.
MENU button [MENU]
Opens the on-screen menu and exits from the menu. Also use to exit the OSD menu
or return to the previous menu.
- VOL+
Moves from one menu item to another horizontally or adjusts selected menu values. When OSD is not on the screen, push the button to adjust volume.
SEL
Moves from one menu item to another vertically or adjusts selected menu values.
/ When OSD is not on the screen, push the button to adjust channel.
Power button [ ]
Use this button for turning the PDP Display on and off.
Power indicator
Shows PowerSaver mode by blinking green
Rear
Introduction
Note
See PowerSaver described in the manual for further information regarding power
saving functions. For energy conservation, turn your PDP Display OFF when it is
not needed or when leaving it unattended for long periods.
Remote Control Sensor
Aim the remote control towards this spot on the PDP Display.
Note
For detailed information concerning cable connections, refer to Connecting Cables under Setup. The
PDP Display 's configuration at the back may vary slightly depending on the PDP Display model.
POWER IN
The power cord plugs into the PDP Display and
the wall plug.
LAN (LAN Connection Terminal)
(Applicable to the P42HN / P50HN model only)
USB(USB Connection Terminal)
Keyboard / Mouse, Mass Storage Device Compatible.
(Applicable to the P42HN / P50HN model only)
Introduction
Note
The number of PDP Displays that can be connected to loopout may differ depending on the cables,
signal source etc. With cables where there is no
degradation or signal source, up to ten PDP Displays can be connected.
RS232C OUT/IN (RS232C Serial PORT)
MDC(Multiple Display Control) Program Port
DVI / PC / HDMI IN [DVI/PC/HDMI AUDIO
IN] (PC/DVI/HDMI Audio Connection Terminal
(Input))
DVI / PC / HDMI IN [HDMI]
Connect the HDMI terminal at the back of your
PDP Display to the HDMI terminal of your digital
output device using a HDMI cable.
DVI / PC / HDMI IN [RGB](PC Video Connection Terminal)
Using a D-Sub Cable (15 pin D-Sub) - PC mode
(Analog PC)
DVI / PC / HDMI IN [DVI] (PC Video Connection Terminal)
Using a DVI Cable (DVI-D to DVI-D) - DVI
mode (Digital PC)
DC Power [OUT]
Connect this to the POWER connector of a TV
tuner box or network box.
AV IN [VIDEO]
Connect the [ VIDEO ] terminal of your monitor
to the video output terminal of the external device
using a VIDEO cable.
AV AUDIO IN [L- AUDIO - R]
Connect the port of the DVD, VCR (DVD / DTV
Set-Top Box) to the [ L- AUDIO - R ] port of the
PDP Display.
Introduction
AUDIO OUT [L- AUDIO - R]
Headphone output terminal.
Kensington Lock
The Kensington Lock is a device used to physically fix the system when using it in a public
place. The locking device has to be purchased
separately. The appearance and locking method
may differ from the illustration depending on the
manufacturer. Refer to the manual provided with
the Kensington Lock for proper use. The locking
device has to be purchased separately.
Note
The location of the Kensington Lock may be different depending on its model.
Note
See Connecting Cables for further information regarding cable connections.
Remote Control
Note
The performance of the remote control may be affected by a TV or other electronic device operating
near the PDP Display , causing a malfunction due to interference with the frequency.
Using the Anti-Theft Kensington Lock
1. Insert the locking device into the Kensington
slot on the Monitor and turn it in the
locking direction .
2. Connect the Kensington Lock cable.
3. Fix the Kensington Lock to a desk or a heavy
stationary object.
Loading...